a Nexans company - BOR ENERJİrubber connectors, terminations and joints for cables and epoxy bushings for transformers and switch gear, as well as a large range of cold-shrinkable

Catalogue 2007

a Nexans company

�

0�/2

007

EUROMOLDCOMPANY PRESENTATION

While every care is taken to ensure that the information contained in this publication is correct, no legal responsibility can be accepted for any inaccuracy. Nexans Network Solutions N.V. - Div. Euromold reserves the right to alter or modify the characteristics of its products

described in this catalogue as standards and technology evolve.

EUROMOLDEuromold is the leading European specialised designer, manufacturer and distributor of prefabricated cable accessories for medium voltage energy distribution. Euromold provides a complete range of acces-sories for underground cables: pre-moulded EPDM or silicone rubber connectors, terminationsand joints for cables and epoxy bushings for transformers and switch gear, as well as a large range of cold-shrinkable terminations and joints from �2 to 42 kV.Euromold is also the manufac-turer of electrical components for the high voltage accessories of the Nexans group.

ISO 9001 CertificateSince �992, Euromold’s commitment to quality is demonstrated by its ISO 900� certification.

Laboratory accreditationSince June 2000, Euromold’s independent ELAB laboratory obtained the BELTEST accredi-tation no.�92-T-ISO �7025 conform with the European standards for laboratories ISO �7025 for electrical testing of medium voltage cable acces-sories according to the Inter-national standards IEC 6�442 and HD 629.

International standardsAll our products meet the International standards like CENELEC HD 629.�, CENELEC EN 50�80, IEC �37, IEEE 386 & 404… or country specifica-tions. Official certificates, CESI, KEMA, ATEX… prove the con-formity of our products. Long duration tests of existing or new products are continuously performed in our test fields.

2

0�/2

007

SEPARABLE CONNECTORSAND BUSHINGS

INTERFACE C

Interface CDimensions according to European CENELEC EN 50�80 and 50�8� (in mm).

M16 x 2 - 6H

11 min.

Dia. 56± 0,2

Dia. 46± 0,2

Dia. 22min.

1,5 0 - 0,5

29min.

90± 0,2

Dia. 70± 0,2

Table of contents400LB - elbow connector430TB-630A - tee connector400TB - tee connector440TB - tee connector300PB-630A - coupling connector400AR-3 - equipment bushing400A-24B - in-air bushingFixings for equipment bushings400PB-XSA - surge arrester400TR & 400TR-LB - test rod400TK-400SW installation toolsAccessoriesPossible arrangements

3

Connecting possibilities

BUSHINGS /ACCESSORIES

CONNECTION CONNECTORS /ACCESSORIES

cable

earthing

tap-off

630/250A

cable

isolation

in-line

junction

one cable to

equipment

dead-ending

of equipment (K)(M)400DR-BDead-end receptacle

in-line

junction

(K)430TB-630ATee connector

(K)400LBElbow connector

(K)(M)(P)400TB/GTee connector

(K)(M)440TB/GTee connector

Equipmentinterface

400GP-BEarthing plug

(K)400RTPAReducing tap plug

(K)(M)400SOP-BStand-off plug

(K)(M)440CPConnecting plug

(K)(M)400AR-3Equipment bushing

400A-24BIn-air bushing

(K)(M)400CP-SCConnecting plug

6

0�/2

007

ApplicationSeparable tee shape connector (bolted type) designed to connect polymeric insulated cable to equipment (transformers, switch gear, motors, ...).Also connects cable to cable when using the appropriate mating parts.

Technical characteristics• A thick conductive EPDM

jacket provides a total safe to touch screen.

• Each separable connector is tested for AC withstand and partial discharge prior to leaving the factory.

Specifications and standardsThe separable connector 430TB-630A meets the requirements of CENELEC HD 629.�.

Up to 24 kV - 630 A

Separableconnector

type

VoltageUm(kV)

CurrentIr

(A)

Conductor sizes (mm2)

min. max.430TB-630A

K430TB-630A

�2

24

630

630

35

35

300

300

Design �. Type C - 630 A interface as described by CENELEC EN 50�80 and 50�8�. 2. Clamping screw. 3. Conductive EPDM insert. 4. Insulating EPDM layer moulded between the insert and the jacket. 5. Conductive EPDM jacket. 6. Conductive rubber cap. 7. Basic insulating plug (standard version without voltage detection point). 8. Conductor connector 9. Cable reducer. �0. Earthing lead.

The screen break designenables cable outer sheathtesting without removing ordismantling the connector.

430TB-630AINTERFACE C

TEE CONNECTOR

6/10 (12) kV6.35/11 (12) kV

8.7/15 (17.5) kV12/20 (24) kV

12.7/22 (24) kV

183 mm

Non-size sensitive:290 mm

Size sensitive:350 mm

3

4

5

7

6

8

9

2

1

10

7

Kit contentsThe complete (K)430TB-630A tee connector kit comprises 3 x the following components:

The kit also comprises lubricant, wipers, water sealing mastic, installation rod, installation instructions and crimp chart.

Ordering instructionsTo order the tee connector, use the tables beside to substitute for W1/W2 and X in the formulas.

�. From table W1 or W2: select the symbol which gives the best centring of your core insulation diameter.

2. From table X: according to your conductor size and type, select the designation which completes the part number.

Example:The cable is 24 kV, �50 mm2 compact stranded copper with a diameter over core insulation of 27.5 mm.Order 3 x K430TB-�8-95.240-�4-5 for a non-size sensitive application or 3 x K430TB-22-�50(K)M-��-2 for a size sensitive application.

Clamping screw

430TCS

Basic insu-lating plug + rubber

cap 300BIPRConnector housing

430BT-630A

Cable reducer430CA-W1

Cable reducer4��CA-W2

Conductorcontact TMBC-X

Conductor contact TBC-X

+ + +

+

+

= 3 x (K)430TB-W1-X connector kit for non-size sensitive

application

3 x (K)430TB-W2-X connector kit for

size sensitiveapplication

=

non-sizesensitive

sizesensitive

Table W1 Table W2

Dia. over coreinsulation (mm) W2

min. max.

�2.0

�6.0

20.0

23.5

26.5

28.5

�7.5

22.0

26.5

3�.0

32.5

37.5

��

�5

�9

22

25

27

For use witheasy strip semi-conductive screened cables. Order: Field control mastic

(type MFC).

Basic insulating plug also available with a voltage

detection point.Order : - /VD.

Table X

For use withother cable types.

Please contact our representative.

For outdoorapplications.

Order: +MWS.

For use withcopper tape

screened cables. Order: Kit MT.

For use with Alupe orC 33-226 cables.


VoltageUm (kV) Non-size sensitive Size sensitive

�2

243 x 430TB-W1-X

3 x K430TB-W1-X3 x 430TB-W2-X

3 x K430TB-W2-X


min. max.

�2.0

�7.0

�9.0

�7.5

23.5

32.6

��

�6

�8

Conduc-tor sizes (mm2)

Aluminium conductor Copper conductor

DINhexagonal

Deepindent

BoltedDIN

hexagonalBolted

35

50

70

95

�20

�50

�85

240

300

35(K)M-�0-2

50(K)M-�0-2

70(K)M-�0-2

95(K)M-�0-2

�20(K)M-�0-2

�50(K)M-�0-2

�85(K)M-�0-2

240(K)M-�0-2

300(K)M-�0-2

35KM-�0-�

50(K)M-�0-�

70(K)M-�0-�

95(K)M-�0-�

�20(K)M-�0-�

�50(K)M-�0-�

�85(K)M-�0-�

240(K)M-�0-�

–

35(K)M-��-2

50(K)M-��-2

70(K)M-��-2

95(K)M-��-2

�20(K)M-��-2

�50(K)M-��-2

�85(K)M-��-2

240(K)M-��-2

300(K)M-��-2– –

8

0�/2

007

Up to 41.5 kV - 630 A

400TBINTERFACE C

TEE CONNECTOR

6/10 (12) kV6.35/11 (12) kV

8.7/15 (17.5) kV12/20 (24) kV

12.7/22 (24) kV18/30 (36) kV19/33 (36) kV

20.8/36 (41.5) kV

Technical characteristics • The thick conductive EPDM

jacket provides a total safe to touch screen which ensures safety for personnel.


Separable connector

type

VoltageUm(kV)

CurrentIr

(A)

Conductor size (mm2)

min. max.

400TB/G

K400TB/G

M400TB/G

P400TB/G

�2

24

36

4�.5

630

630

630

630

35

35

35

35

300

300

240

240


DesignSeparable connector comprising: �. Conductive EPDM insert. 2. Conductive EPDM jacket. 3. Insulating EPDM layer. 4. Type C - 630 A interface as described by CENELEC EN 50�80 and 50�8�. 5. Conductor connector. 6. Basic insulating plug (with VD point). 7. Cable reducer. 8. Conductive rubber cap. 9. Clamping screw. �0. Earthing lead.


Specifications and standardsThe separable connector 400TB meets the requirements of CENELEC HD 629.� S�.

255 mm

220 mm

390 mm

3

2

1

4

56

7

8

10

9

9




Order: +MWS.

Components can be ordered individually.



For use with Alupe orC 33-226 cables.


For use in potentially explosive atmospheres

(for �2 kV max.). Order: -/ATEX.

Kit contentsThe complete (K)(M)(P)400TB/G tee connector kit comprises the following components:

The kit also comprises lubricant, wipers,

installation instructions and crimp chart.

Ordering instructionsTo order the tee connector, select the ordering part number which gives you the best centring of your core insula-tion diameter and substitute X using table X, according to your conductor size and type.Add a 'K' for use up to 24 kV, an 'M' for use up to 36 kV or add a 'P' for use up to 4�.5 kV.

Orderingpart number

Dia. over core insulation (mm)

min. max.

400TB/G-��-X400TB/G-�5-X400TB/G-�9-X400TB/G-22-X400TB/G-25-X400TB/G-27-X

�2.0

�6.0

20.0

23.5

26.5

28.5

�7.5

22.0

26.5

3�.0

32.5

37.5

Example:The copper wire screened cable is 36 kV, �50 mm2 stranded copper with a diameter over core insulation of 32.5 mm.Order a M400TB/G-27-�50(K)M-��-2 tee connector kit.

Connector housing

(K)(M)(P)400BT/G

Clamping

screw

400TCS

Conductor

contact

TBC-X

Basic insulating

plug +

rubber cap

(K)(M)(P)400BIPA

Cable reducer

4��CA-W

(K)(M)(P)400TB/G-W-Xconnector kit

Table W

Table X

Conductor size (mm2)


DINhexagonal

Deepindent

DINhexagonal

35

50

70

95

�20

�50

�85

240

300

35(K)M-�2-2

50(K)M-�2-2

70(K)M-�2-2

95(K)M-�2-2

�20(K)M-�2-2

�50(K)M-�2-2

�85(K)M-�2-2

240(K)M-�2-2

300(K)M-�2-2

35KM-�2-�

50KM-�2-�

70KM-�2-�

95KM-�2-�

�20KM-�2-�

�50KM-�2-�

�85KM-�2-�

240KM-�2-�

300KM-�2-�

35(K)M-��-2

50(K)M-��-2

70(K)M-��-2

95(K)M-��-2

�20(K)M-��-2

�50(K)M-��-2

�85(K)M-��-2

240(K)M-��-2

300(K)M-��-2

+ + + + =

�0

0�/2

007

6/10 (12) kV6.35/11 (12) kV

8.7/15 (17.5) kV12/20 (24) kV

12.7/22 (24) kV18/30 (36) kV

Up to 36 kV - 630 A

440TBINTERFACE C

TEE CONNECTOR

Technical characteristics • The thick conductive EPDM

jacket provides a total safe to touch screen which ensures safety for personnel.



DesignSeparable connector comprising: �. Conductive EPDM insert. 2. Conductive EPDM jacket. 3. Insulating EPDM layer moulded between the insert and the jacket. 4. Type C - 630 A interface as described by CENELEC EN 50�80 and 50�8�. 5. Conductor connector. 6. Basic insulating plug (with VD point). 7. Cable reducer. 8. Conductive rubber cap. 9. Clamping screw. �0. Earthing lead.


Specifications and standardsThe separable connector 440TB meets the requirements of CENELEC HD 629.�.

Separable connector

type

VoltageUm(kV)

CurrentIr

(A)


min. max.440TB/G

K440TB/G

M440TB/G

�2

24

36

630

630

630

�85

�85

�85

630

630

630

400 mm

3

2

1

4

5

7

6 8

10

9

255 mm220 mm

��

Kit contentsThe complete (K)(M)440TB/G tee connector kit comprises the following components:

The kit also comprises lubricant, wipers,


Ordering instructionsTo order the tee connector, select the ordering part number which gives you the best centring of your core insula-tion diameter and substitute X using table X, according to your conductor size and type.Add a 'K' for use up to 24 kV and add an 'M' for use up to 36 kV.

Orderingpart number

Dia. over core insulation (mm)

min. max.

440TB/G-22-X440TB/G-27-X440TB/G-32-X440TB/G-37-X440TB/G-43-X

23.5

28.5

34.0

39.0

45.5

3�.0

37.5

42.5

48.5

56.0

Example:The copper wire screened cable is 36 kV, 240 mm2 stranded aluminium with a diameter over core insulation of 37.0 mm.Order a M440TB/G-32-240(K)M-�2-2 tee connector kit.

When installed on an appropriate equipment

bushing: �250 A continuously



+ + +

Connector housing

(K)(M)440BT/G

Clamping

screw

400TCS

Conductor

contact

TBC-X

Basic

insulating

plug +

rubber cap

(K)(M)400BIPA

+

Cable reducer

6��CA-W

= (K)(M)440TB/G-W-Xconnector kit

Table W

Table X



DINhexagonal

Deepindent

DINhexagonal

�85

240

300

400

500

630

�85(K)M-�2-2

240(K)M-�2-2

300(K)M-�2-2

400(K)M-�2-2

500(K)M-�2-2–

�85KM-�2-�

240KM-�2-�

300KM-�2-�

400KM-�2-�

500KM-�2-�

630KM-�2-�

�85(K)M-��-2

240(K)M-��-2

300(K)M-��-2

400(K)M-��-2

500(K)M-��-2

630(K)M-��-2




Order: +MWS.

Components can be ordered individually.

For use in potentially explosive atmospheres

(for �2 kV max.). Order: -/ATEX.

�2

0�/2

007

ApplicationSeparable coupling connector (bolted type) for dual cable arrangement. It has been designed to be used with separable Tee connector 430TB-630A. Total maximum current is 630 A.

Technical characteristics• A thick conductive EPDM

jacket provides a total safe to touch screen.


Up to 24 kV - 630 A

300PB-630ACOUPLING CONNECTOR

FOR 430TB-630A

Separableconnector

type

VoltageUm(kV)

CurrentIr

(A)


min. max.300PB-630A

K300PB-630A

�2

24

630

630

35

35

300

300

6/10 (12) kV6.35/11 (12) kV

8.7/15 (17.5) kV12/20 (24) kV

12.7/22 (24) kV

3

2

1

4

5

7

8

10

9

Non-size sensitive:290 mm

Size sensitive:350 mm

105 mm

290 mm

11

6

Specifications and standardsThe 300PB-630A coupling connector meets the requirements of CENELEC HD 629.� for �0 and 20 kV levels.

Design �. Interface designed to fit 430TB-630A connector. 2. Bus for 300PB. 3. Conductive EPDM insert. 4. Insulating EPDM layer moulded between the insert and the jacket. 5. Conductive EPDM jacket. 6. Conductive EPDM cap. 7. Basic insulating plug. 8. Conductor connector (hexagonal crimping, deep indent crimping or bolted). 9. Cable reducer. �0. Clamping screw. ��. Earth lead.


�3

Kit contentsThe complete (K)300PB-630Acoupling connector kit comprises 3 x the following components:

The kit also comprises silicone grease,

water sealing mastic, installation rod,


Ordering instructionsTo order the Tee connector, use the tables beside to substitute for W1/W2 and X in the formulas.

�. From table W1 or W2: select the symbol which gives the best centring of your core insulation diameter.

2. From table X: according to your conductor size and type, select the designation which completes the part number.

Example:The cable is 24 kV, �50 mm2 compact stranded copper with a diameter over core insulation of 27.5 mm.Order 3 x K300PB-�8-95.240-�4-5 for a non-size sensitive application or 3 x K300PB-22-�50(K)M-��-2 for a size sensitive application.

Clamping screw

300PB-CS

Connector housing300BPB-630A

+



For use witheasy strip semi-conductive screened cables. Order: Field control mastic

(type MFC).

For use with copperwire screened cables.

No earthingdevice is

necessary.




Order: +MWS.

Cable reducer430CA-W1

Cable reducer4��CA-W2

Conductorcontact TMBC-X

Conductor contact TBC-X

+

+

+

= 3 x (K)300PB-W1-X connector kit for non-size sensitive

application

3 x (K)300PB-W2-X connector kit for

size sensitiveapplication

=

non-sizesensitive

sizesensitive

For use with fabric tape (graphite) screened cables.

Order additionalsemi-conductive tape

(type TSC).

VoltageUm (kV) Non-size sensitive Size sensitive

�2

243 x 300PB-W1-X

3 x K300PB-W1-X3 x 300PB-W2-X

3 x K300PB-W2-X

Table W1 Table W2


min. max.

�2.0

�6.0

20.0

23.5

26.5

28.5

�7.5

22.0

26.5

3�.0

32.5

37.5

��

�5

�9

22

25

27

Table X


min. max.

�2.0

�7.0

�9.0

�7.5

23.5

32.6

��

�6

�8

Conduc-tor sizes (mm2)


DINhexagonal

Deepindent

BoltedDIN

hexagonalBolted

35

50

70

95

�20

�50

�85

240

300

35(K)M-�0-2

50(K)M-�0-2

70(K)M-�0-2

95(K)M-�0-2

�20(K)M-�0-2

�50(K)M-�0-2

�85(K)M-�0-2

240(K)M-�0-2

300(K)M-�0-2

35KM-�0-�

50(K)M-�0-�

70(K)M-�0-�

95(K)M-�0-�

�20(K)M-�0-�

�50(K)M-�0-�

�85(K)M-�0-�

240(K)M-�0-�

–

35(K)M-��-2

50(K)M-��-2

70(K)M-��-2

95(K)M-��-2

�20(K)M-��-2

�50(K)M-��-2

�85(K)M-��-2

240(K)M-��-2

300(K)M-��-2– –

�8

0�/2

007

ApplicationSurge arrester designed to protect �2 and 24 kV class components, including transformers, equipment, cable and accessories from high voltage surges resulting from lightning or switching.

Up to 36 kV

400PB-XSAINTERFACE C

SURGE ARRESTER

6/10 (12) kV6.35/11 (12) kV

8.7/15 (17.5) kV12/20 (24) kV

12.7/22 (24) kV18/30 (36) kV

Technical characteristics • This surge arrester is a metal

oxide varistor surge arrester in an elbow configuration.

• Each arrester is tested for AC withstand and partial discharge prior to leaving the factory.

Surgearrester

type

Nominal discharge

currentIn (kA)

Rated voltage

Ur(kV)

Max. continuousoperatingvoltageUc (kV)

Steep currentresidual

voltage @ 5 kA[1/20 µs] (kV)

Lightning currentresidual

voltage @ 5 kA[8/20 µs] (kV)

High currentimpulse

withstand(kA)

Dimensions(mm)

L1 L2

400PB-5SA-�5L400PB-5SA-�8L400PB-5SA-22L400PB-5SA-24L400PB-5SA-30L

400PB-�0SA-�5N400PB-�0SA-�8N400PB-�0SA-22N400PB-�0SA-24N400PB-�0SA-30N400PB-�0SA-36N400PB-�0SA-45N

55555�0�0�0�0�0�0�0

�5�8222430�5�82224303645

�2.0�4.4�7.6�9.224.0�2.0�4.0�7.6�9.224.028.836.0

42.452.765.770.087.346.256.068.974.492.7��.��38.2

40.048.059.064.080.040.248.659.864.580.496.4�20.0

6565656565�00�00�00�00�00�00�00

250250350350350250250350350350350450

290290390390390290290390390390390490

DesignSurge arrester comprising:�. Conductive EPDM insert.2. Conductive EPDM jacket.3. Insulating EPDM layer moulded between the insert and the jacket.4. Contact rod.5. Earth lead.6. Earth connection.7. Steel cap.8. Metal oxide valve elements.9. Type C - 630 A interface as described by CENELEC EN 50�80 and 50�8�.

6

9

5

4

3

2

1

252 mm

L2L1

150 mm

Dia.80 mm

7

Dia.70 mm

8

�9

Typical application anddimensions

Ordering instructionsTo order the surge arrester, specify the surge arrester type, as described on previous page.

Example:For a maximum continuous operating voltage (rms) of 24 kV and a nominal discharge current of �0 kA.Order a 400PB-�0SA-24N surge arrester.

410 mm

220 mm 185 mm

Type 400PB-5SAor 400PB-10SAsurge arrester

Type 400TB/Gor K400TB/Gtee connector

355 mm

150 mm 202 mm

Type 400LBor K400LB

elbow connector


335 mm

150 mm 183 mm

Type 430TBor K430TBtee connector


20

0�/2

007

400TR and 400TR-LBINTERFACE C

TEST RODS

Application• The test rod can be used for: - cable fault location - cable testing - phasing checks, etc.• Connections may be made

with a cable lug, a 4 mm plug or spring clips.

InstallationThe test rod is mounted onto the clamping screw in the type C interface tee and coupling connectors. The test cable is connected to the threaded stem and the insulating shroud moved to its final position over the end of the test rod.

Design�. Insulating shroud.2. Threaded rod for test connection.3. Two nuts M�2.4. Insulation.5. Copper test rod stem.6. Wing nut.

An insulating shroud isprovided to allow theapplication of test voltageswhen bushings are closelyspaced.

Test rod type

Maximum A.C.test voltage

(50 Hz - 1 min.)

Maximum D.C.test voltage

(8 x U0 - 30 min.)

Impulse voltage (1.2 x 50 µs)

min.

400TR

400TR-LB

36 kV

36 kV

96 kV

96 kV

95 kV

95 kV

Technical characteristics • The 400TR test rod can

be used with 400TE, 430TB, 400TB and 440TB connectors.

• The 400TR-LB is for use with the 400LB connector.

480

4

5

2

288

40

1

3

M12

In mm.

400TR 400TR-LB

370

60

1

5

6

2

Dia.25

M10

4

Ordering instructionsSimply specify:400TR or 400TR-LB test rod.

22

0�/2

007

ACCESSORIESINTERFACE C

Up to 36 kVApplicationFor use with connectors and bushings with an interface C as described by CENELEC EN 50�80 and 50�8�.

Technical characteristics All these products, except theearthing plugs, are tested forAC withstand and partial discharge prior to leavingthe factory.

6/10 (12) kV6.35/11 (12) kV

8.7/15 (17.5) kV12/20 (24) kV

12.7/22 (24) kV18/30 (36) kV

400SOP-BStand-off plugIs designed to support and 'dead-end' connectors with a type C interface when removed from equipment.

Ordering instructionsOrder 400SOP-B for �2 kV,K400SOP-B for 24 kV orM400SOP-B for 36 kVapplications.

400GP-BEarthing plugIs designed to support and earth connectors with a type C interface when removed from equipment.

Ordering instructionsOrder 400GP-B for �2, 24 or 36 kV applications.

300GP-BEarthing plugIs designed to earth the 430TB-630A connectors when it is fixed-mounted to the equipment (maintenance earthing).

Ordering instructionsOrder 300GP-B for �2 or 24 kVapplications.

400DR-BDead-end receptacleFits over a bushing with a type C interface to provide 'dead-end' facility.

Ordering instructionsOrder 400DR-B for �2 kV,K400DR-B for 24 kV orM400DR-B for 36 kVapplications.The dead-end receptacle canbe supplied with an earth lead.Order: -/G.E.g. K400DR-B/G.

23

Kit MTEarthing kit for copper tape screened cablesContains a tinned copper braid (25 mm² - L = 500 mm), a tinned copper wire for cleating and some water sealing mastic.

Ordering instructionsOrder Kit MT for �2 kV, 24 kV 36 kV or 4�.5 kV applications.

440CPConnecting plugFor connecting two or more 440TB connectors, thus creating a separable cable joint or a multiple cable connection to equipment.For use up to �250 A.Only for use with 440TB.

400RTPAReducing tap plugProvides a type A interface to connectors with a type C interface.A 'C' spanner, 600SW, is used to tighten the reducing tap plug on to its mating part.

Ordering instructionsOrder 400RTPA for �2 kV or K400RTPA for 24 applications.Order 600SW for the 'C'spanner.

400CP-SCConnecting plugFor connecting two or more connectors with a type C interface together, thus creating a separable cable joint or a multiple cable connection to equipment.

Ordering instructionsOrder 400CP-SC for �2 kV, K400CP-SC for 24 kV orM400CP-SC for 36 kVapplications.

400BIPABasic insulating plugActs as a tightening nut for the 400TB and 440TB tee connector kits.The plug contains a voltage detection point.The conductive rubber protection cap is included.

Ordering instructionsOrder 400BIPA for �2 kV, K400BIPA for 24 kV orM400BIPA for 36 kVapplications.

Ordering instructionsOrder 440CP for �2 kV, K440CP for 24 kV orM440CP for 36 kVapplications.Order: -/ATEX for use in potentially explosive atmospheres (for �2 kV max.).

24

0�/2

007

POSSIBLE ARRANGEMENTSINTERFACE C

430TBSingle cable arrangement.Order 430TB for �2 kV or K430TB for 24 kV applications.

430TB+300PBDual cable arrangement.Order 430TB+300PB for �2 kV or K430TB+K300PB for 24 kV applications.

400TB/GSingle cable arrangement.Order 400TB/G for �2 kV, K400TB/G for 24 kV,M400TB/G for 36 kV or P400TB/G for 4�.5 kV applications.

In mm.

183

110

teeconnector

basicinsulatingplug

250

110

teeconnector

basicinsulatingplug

290

110 105

teeconnector

couplingconnector

basicinsulatingplug

400TB/G-P2Dual cable arrangement.Order 400TB/G-P2 for �2 kV, K400TB/G-P2 for 24 kV or M400TB/G-P2 for 36 kV applications.

connectingplug

500

110 245

basicinsulating

plug

25

In mm.

400TB/G-L4Disconnectable tap-off.Order 400TB/G-L4 for �2 kV, K400TB/G-L4 for 24 kV or M400TB/G-L4 for 36 kV applications.

1020

basicinsulating

plug

connectingplug

connectingplugs

basicinsulating

plug

400TB/G-L22-way connection.Order 400TB/G-L2 for �2 kV, K400TB/G-L2 for 24 kV or M400TB/G-L2 for 36 kV applications.

400TB/G-L52-way connection with tap-off.Order 400TB/G-L5 for �2 kV or K400TB/G-L5 for 24 kV applications.

connecting plug

530

basicinsulating

plug

basicinsulating

plug

505

type Aseparableconnector

reducingtap plugbasic

insulatingplug

400TB/G-L33-way connection.Order 400TB/G-L3 for �2 kV, K400TB/G-L3 for 24 kV or M400TB/G-L3 for 36 kV applications.

775

basicinsulating

plug

basicinsulating

plug

connectingplug

connectingplug

26

Connector on earthing plugOrder 400GP-B for �2 kV, 24 kV and 36 kV applications.

earthingplug

basicinsulating

plug

Earthing plug on connectorOrder 300GP-B for �2 kV and24 kV applications.

430TB teeconnector

300GPB earthing plug

Connector on stand-off plugOrder 400SOP-B for �2 kV, K400SOP-B for 24 kV or M400SOP-B for 36 kV applications.

stand-offplug

basicinsulating

plug

27

In mm.

110

600

insulatingshroud

400TRtest rod

400TB or 440TBtee connector

110

430TB teeconnector

600

insulatingshroud

400TRtest rod

Cable and equipment testing.

125

400LB elbowconnector

515

insulatingshroud

400TR-LBtest rod

Additional catalogue information on power cable accessoriesis available by contacting us at the address below:

Nexans Network Solutions N.V. - Div. Euromold • Zuid III, Industrielaan �2, B-9320 ErembodegemTel.: +32 (0)53 85 02 �� • Fax: +32 (0)53 83 �0 �3 • www.nexans.com • [email protected]

Catalogue also available on CD-ROM

Distributed by:

0�/2

007

CBIR

Textfeld

Nexans Power Accessories Germany GmbH • Aplerbecker Straße 456 • D-44287 Dortmund Tel.: +49 (0)231 945 13 0 • Fax: +49 (0)231 945 13 22 • www.euromold.de • [email protected]

Documents

a Nexans company - BOR ENERJİrubber connectors, terminations and joints for cables and epoxy bushings for transformers and switch gear, as well as a large range of cold-shrinkable