A Test Lab Techno Corp. - APC · A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, ... The above equipment has been tested by A Test Lab Techno Corp., …

FCC 47 CFR PART 15 SUBPART B Product Type ： Power Filter

Applicant ： Schneider Electric IT (China) Co., LTD

Address ： Sec A2, 3F, No. 25 building of New Zone, 30 Fute Dongsan Road, Waigaoqiao Bonded Area, Shanghai, China

Trade Name ： APC

Model Number ： C25B

Test Specification

： FCC 47 CFR PART 15 SUBPART B: Oct., 2010 ANSI C63.4: 2009 CISPR 22: 1997 ICES-003: Issue 4

Receive Date ： Dec. 06, 2011

Issue Date ： Dec. 14, 2011

Issue by

A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Tel：+886-3-2710188 / Fax：+886-3-2710190 Taiwan Accreditation Foundation accreditation number: 1330

Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample.

A Test Lab Techno Corp. Report Number: 1112FE14

1/28

Revision History

Rev. Issue Date Revisions Revised By

00 Dec. 14, 2011 Initial Issue


2/28

Verif ication of Compliance

Issued Date: 2011/12/14

Product Type : Power Filter

Applicant : Schneider Electric IT (China) Co., LTD

Address : Sec A2, 3F, No. 25 building of New Zone, 30 Fute Dongsan Road, Waigaoqiao Bonded Area, Shanghai, China

Trade Name : APC

Model Number : C25B

EUT Rated Voltage : AC 120V~, 50/60Hz, 15A

Test Voltage : 120 Vac / 60 Hz

Applicable

Standard

: FCC 47 CFR PART 15 SUBPART B: Oct., 2010

ANSI C63.4: 2009

CISPR 22: 1997

ICES-003: Issue 4

Test Result : Complied

Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Tel：+886-3-2710188 / Fax：+886-3-2710190 Taiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm

The above equipment has been tested by A Test Lab Techno Corp., and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties.

Approved By ：

Reviewed By ：

(Manager) (Murphy Wang) (Testing Engineer) (Charlie Chang)


3/28

TABLE OF CONTENTS

1 General Information .......................................................................................................................5

2 EUT Description .............................................................................................................................6

3 Test Methodology...........................................................................................................................7

3.1. Decision of Test Mode ............................................................................................................7

3.2. EUT System Operation...........................................................................................................7

3.3. Configuration of Test System Details......................................................................................8

3.4. Test Site Environment.............................................................................................................9

4 Emission Test ...............................................................................................................................10

4.1. Conducted Emission Measurement .....................................................................................10

4.2. Radiated Interference Measurement....................................................................................15

5 EUT Photograph ...........................................................................................................................25


4/28

1 General Information

1.1 Summary of Test Result

Emission

Standard Item Result Remark

FCC 47 CFR PART 15 SUBPART B: Oct., 2010ANSI C63.4: 2009 ICES-003: Issue 4

15.107: Conducted Emission PASS Meet Class B limit

FCC 47 CFR PART 15 SUBPART B: Oct., 2010ANSI C63.4: 2009 ICES-003: Issue 4

15.109: Radiated Emission PASS Meet Class B limit

The test results of this report relate only to the tested sample(s) identified in this report. Manufacturer or whom it

may concern should recognize the pass or fail of the test result.

1.2 Measurement Uncertainty

Conducted Emission

The measurement uncertainty is evaluated as ± 2.24 dB.

Conducted Emissions (Telecommunication Ports)

The measurement uncertainty is evaluated as ± 2.24 dB.

Radiated Emission

The measurement uncertainty of 30 MHz - 1GHz is evaluated as ± 3.072dB.

The measurement uncertainty of 1GHz - 40GHz is evaluated as ± 3.072dB.


5/28

2 EUT Description

Product ： Power Filter

Trade Name ： APC

Model Number ： C25B

Applicant ： Schneider Electric IT (China) Co., LTD Sec A2, 3F, No. 25 building of New Zone, 30 Fute Dongsan Road, Waigaoqiao BondeArea, Shanghai, China

Manufacturer ： Schneider Electric IT (China) Co., LTD Sec A2, 3F, No. 25 building of New Zone, 30 Fute Dongsan Road, Waigaoqiao BondeArea, Shanghai, China

I/O Port Description：

I/O PORT TYPES Q’TY Test Description

1). AC Power Port 1 Connected to Lamp Load

2). AC Power Port 9 Connected to Terminal

3). Telecom Port 1 Connected to Telephone

4). Telecom Port 1 Connected to Exchange Network

5). Coaxial 1 Connected to Terminal

6). Coaxial 1 Connected to DTV SG


6/28

3 Test Methodology

3.1. Decision of Test Mode

3.1.1 The following test mode(s) were scanned during the preliminary test:

Pre-Test Mode

Mode 1: Normal Operation Mode

3.1.2 After the preliminary scan, the following test mode was found to produce the highest emission

level.

Final Test Mode

Conducted Emission Mode 1

Below 1GHz Mode 1 Emission Radiated Emission Above 1GHz Mode 1

Then, the above highest emission mode of the configuration of the EUT and cable was chosen for all final test

items.

3.2. EUT Exercise Software

1. Setup the EUT and simulators as shown on 3.3.

2. Turn on the power of all equipment.

3. Telecom signal was communicate between telephone and partner telephone through the telecom port of the EUT.

4. Repeat the above procedure (3).


7/28

AC Input

3.3. Configuration of Test System Details

Signal Cable Type Signal Cable Description

A Power Cable Non-Shielded, 1.8m

B Power Cable Non-Shielded, 1.8m

C Coaxial Cable Non-Shielded, 1.0m

D Telephone Cable Non-Shielded, 3.0m

E Telephone Cable Non-Shielded, 1.0m

F Telephone Cable Non-Shielded, 1.0m

G Coaxial Cable Non-Shielded, 3.0m

H AC Power Cable Non-Shielded, 2.5m

Devices Description

Product Manufacturer Model Number Serial Number Power Cord

1. Lamp Load N/A N/A N/A N/A

2. Telephone H.T.T. N/A N/A N/A

3. Telephone H.T.T. N/A N/A N/A

4. Exchange Network Smart UK-106 N/A N/A

5. DTV SG BSK DTV-550 N/A Non-Shielded, 1.8m

EUT

Terminal

(2) Telephone

(1) Lamp Load

(3) Telephone

(4) Exchange Network

A

B B B B B BH

BBB

E

(5) DTV SG

DG

F

C


8/28

3.4. Test Site Environment

Items Test Item Required (IEC 68-1) Actual

Temperature (°C) 15-35 26 Humidity (%RH) 25-75 60 Barometric pressure (mbar)

FCC part 15: 15.107

Conducted Emission 860-1060 950 Temperature (°C) 15-35 23 Humidity (%RH) 25-75 49 Barometric pressure (mbar)

FCC part 15: 15.109

Radiated Emission 860-1060 950


9/28

4 Emission Test 4.1. Conducted Emission Measurement

4.1.1. Limit

A.C. Mains Conducted Interference Limit： Class A (dBuV) Class B (dBuV)

Frequency (MHz) Quasi-peak Average Quasi-peak Average

0.15 - 0.5 79 66 66 - 56 56 - 46

0.50 - 5.0 73 60 56 46

5.0 - 30.0 73 60 60 50

NOTE: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range 0.15 to 0.50 MHz.

4.1.2. Test Instruments

Description Manufacturer Model Number Serial Number Cal. Date Remark

Test Receiver R&S ESCI 100367 06/30/2011 (1)

LISN R&S ENV216 101040 03/04/2011 (1)

LISN R&S ENV216 101041 03/04/2011 (1)

Test Site ATL TE02 TE02 N.C.R. -----

Remark: (1) Calibration period 1 year. (2) Calibration period 2 years.

NOTE: N.C.R. = No Calibration Request. 4.1.3. Test Setup

A.C. mains setup


10/28

4.1.4. Test Procedure

The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.).

This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also

connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm

termination.

For A.C. mains conducted interference, measured both sides of A.C. lines and carried out using quasi-peak and

average detector receivers of maximum conducted interference.

Conducted emissions were invested over the frequency range from 0.15 MHz to 30 MHz using a receiver

bandwidth of 9 kHz. The equipment under test (EUT) shall be meet the limits in section 4.1.1, as applicable,

including the average limit and the quasi-peak limit when using respectively, an average detector and quasi-peak

detector measured in accordance with the methods described of related standard. The voltage limits shall be met. If

the average limit is met when using a quasi-peak detector receiver, the EUT shall be deemed to meet both limits

and measurement with the average detector receiver is unnecessary.

If the reading of the measuring receiver shows fluctuations close to the limit, the reading shall be observed for at

least 15 s at each measurement frequency; the higher reading shall be recorded with the exception of any brief

isolated high reading which shall be ignored.


11/28

4.1.5. Test Result

Standard: FCC Part 15B Class B Line: L1

Test item: Conducted Emission Power: AC 120V/60Hz

Model: C25B Temp.(℃)/Hum.(%RH): 26(℃)/60%RH

Mode: Mode 1 Date: 12/13/2011

Test By: Charlie Chang

Description:

Frequency QP

readingAVG

reading Correction

factor QP

resultAVG result

QP limit

AVG limit

QP margin

AVG margin

No.

(MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)

Remark

1 0.1540 39.07 24.11 10.07 49.14 34.18 65.78 55.78 -16.64 -21.60 Pass

2 0.1780 35.77 22.17 10.06 45.83 32.23 64.58 54.58 -18.75 -22.35 Pass

3 0.1980 37.14 23.74 10.05 47.19 33.79 63.69 53.69 -16.50 -19.90 Pass

4 0.2180 30.53 17.74 10.04 40.57 27.78 62.89 52.89 -22.32 -25.11 Pass

5 0.2660 32.00 20.51 10.03 42.03 30.54 61.24 51.24 -19.21 -20.70 Pass

6 2.2380 29.98 19.82 9.71 39.69 29.53 56.00 46.00 -16.31 -16.47 Pass


12/28

Standard: FCC Part 15B Class B Line: N

Test item: Conducted Emission Power: AC 120V/60Hz



Test By: Charlie Chang

Description:

Frequency QP

readingAVG

reading Correction

factor QP

resultAVG result

QP limit

AVG limit

QP margin

AVG margin

No.

(MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB)

Remark

1 0.1540 37.24 22.00 10.15 47.39 32.15 65.78 55.78 -18.39 -23.63 Pass

2 0.1700 34.93 19.96 10.14 45.07 30.10 64.96 54.96 -19.89 -24.86 Pass

3 0.1940 37.08 24.08 10.13 47.21 34.21 63.86 53.86 -16.65 -19.65 Pass

4 0.2060 35.40 21.77 10.13 45.53 31.90 63.37 53.37 -17.84 -21.47 Pass

5 0.2700 30.71 20.11 10.10 40.81 30.21 61.12 51.12 -20.31 -20.91 Pass

6 2.2820 31.82 20.92 9.77 41.59 30.69 56.00 46.00 -14.41 -15.31 Pass


13/28

4.1.6. Test Photograph

A.C. Mains:

Test Mode : Mode 1

Description : Front View of Conducted Test

Test Mode : Mode 1

Description : Back View of Conducted Test


14/28

4.2. Radiated Interference Measurement

4.2.1. Limit

Under 1GHz test shall not exceed following value: FCC 47 CFR PART 15 SUBPART B

Class A Class B Frequency range

(MHz) Distance (m) dBuV/m Distance (m) dBuV/m

30 to 88 10 39 3 40

88 to 216 10 43.5 3 43.5

216 to 960 10 46.4 3 46

Above 960 10 49.5 3 54

CISPR 22

Class A Class B Frequency range

(MHz) Distance (m) dBuV/m Distance (m) dBuV/m

30 to 230 10 40 10 30

230 to 1000 10 47 10 37

Above 1GHz test shall not exceed following value:

dBuV/m (Distance 3m)

Class A Class B Frequency

(MHz) Average Peak Average Peak

1000 ~ 40000 49.5 69.5 54 74

Remark: 1. The tighter limit shall apply at the edge between two frequency bands. 2. Distance refers to the distance in meters between the measuring instrument antenna and the closed

point of any part of the device or system. 3. RF Voltage (dBuV/m) = 20 log RF Voltage (uV/m) 4. Peak detector limit is corresponding to 20 dB above the maximum permitted average limit.


15/28

4.2.2. Test Instruments

3 Meter Chamber

Equipment Manufacturer Model Number Serial Number Cal. Date Remark

Spectrum Analyzer Agilent E4445A MY46181986 06/16/2011 (1)

Amplifier Mini-Circuits ZKL-1R5+ N/A 05/30/2011 (1)

Amplifier Mini-Circuits ZVA-213-S+ N/A 05/30/2011 (1)

RF Pre-selector Agilent N9039A MY46520255 05/16/2011 (1)

Double-Ridged Waveguide Horn

ETS-Lindgren 3117 00128055 08/24/2010 (1)

Trilog-Broadband Antenna

Schwarzbeck Mess-Elektronik

SB AC VULB 9168-419 05/10/2011 (1)

Test Site ATL TE09 TE09 05/13/2011 (1)

Remark: (1) Calibration period 1 year. (2) Calibration period 2 years.

NOTE: N.C.R. = No Calibration Request.


16/28

4.2.3. Setup

Below 1GHz

Above 1GHz


17/28

4.2.4. Test Procedure

The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. When the EUT is floor-

standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the

EUT from the ground plane.

The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was

positioned such that the distance from antenna to the EUT was 10 meters for under 1GHz, and 3 meter for above

1GHz, the highest frequency performed according to internal source frequency of the EUT, the specification was

below:

Highest frequency generated or used in the device or on which the device operates or tunes (MHz)

Upper frequency of measurement range (MHz)

Below 1.705 30

1.705 - 108 1000

108 - 500 2000

500 - 1000 5000

Above 1000 5th harmonic of the highest frequency or 40 GHz,

whichever is lower

According to this standard paragraph 15.109, as an alternative to the radiated emission limits, digital devices may

be shown to comply with the standards contained in Third Edition of the International Special Committee on Radio

Interference (CISPR), Pub. 22, “Information Technology Equipment - Radio Disturbance Characteristics - Limits

and Methods of Measurement”.

The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both

horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission,

all of the interface cables must be manipulated on radiated measurement.

Radiated emissions were invested over the frequency range from 30MHz to1GHz using a receiver bandwidth of

120 kHz. Radiated was performed at an antenna to EUT distance of 10 meters.


18/28

4.2.5. Test Result

Standard: CISPR 22 Class B Test Distance: 3m

Test item: Radiated Emission Power: AC 120V/60Hz



Ant.Polar.: Horizontal Test By: Charlie Chang

Frequency Reading Correct Result Limit Margin Height DegreeNo. (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) (cm) ( ° )

Remark

1 64.0000 31.87 -17.80 14.07 40.00 -25.93 300 21 QP

2 187.0000 31.14 -18.37 12.77 43.50 -30.73 200 0 QP

3 315.0000 27.27 -14.71 12.56 46.00 -33.44 200 60 QP

4 423.0000 26.92 -11.69 15.23 46.00 -30.77 100 180 QP

5 875.5000 24.43 -3.10 21.33 46.00 -24.67 400 25 QP

6 940.0000 26.33 -2.36 23.97 46.00 -22.03 400 227 QP


19/28

Standard: CISPR 22 Class B Test Distance: 3m




Ant.Polar.: Vertical Test By: Charlie Chang

Frequency Reading Correct Result Limit Margin Height DegreeNo. (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB) (cm) ( ° )

Remark

1 64.0000 35.65 -17.80 17.85 40.00 -22.15 100 221 QP

2 167.0000 32.67 -16.58 16.09 43.50 -27.41 100 0 QP

3 187.0000 36.14 -18.37 17.77 43.50 -25.73 100 132 QP

4 824.0000 45.41 -4.12 41.29 46.00 -4.71 200 45 QP

5 875.5000 28.59 -3.10 25.49 46.00 -20.51 400 0 QP

6 940.0000 28.35 -2.36 25.99 46.00 -20.01 100 90 QP


20/28

Standard: FCC Part 15B Class B Test Distance: 3m



Mode: Mode 1 (1GHz~6GHz) Date: 12/13/2011

Ant.Polar.: Horizontal Test By: Charlie Chang

Frequency Reading Correct Result Limit Margin No. (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB)

Remark

1 1585.000 64.86 -25.59 39.27 74.00 -34.73 peak

2 3540.000 62.24 -20.48 41.76 74.00 -32.24 peak

3 5250.000 58.72 -14.84 43.88 74.00 -30.12 peak


21/28

Standard: FCC Part 15B Class B Test Distance: 3m



Mode: Mode 1 (1GHz~6GHz) Date: 12/13/2011

Ant.Polar.: Vertical Test By: Charlie Chang

Frequency Reading Correct Result Limit Margin No. (MHz) (dBuV) Factor(dB/m) (dBuV/m) (dBuV/m) (dB)

Remark

1 2245.000 64.47 -23.99 40.48 74.00 -33.52 peak

2 4610.000 60.02 -16.61 43.41 74.00 -30.59 peak

3 5700.000 58.78 -13.58 45.20 74.00 -28.80 peak


22/28

4.2.6. Test Photograph

Test Mode : Mode 1

Description : Front View of Radiated Emission Test _ Below 1GHz

Test Mode : Mode 1

Description : Back View of Radiated Emission Test _ Below 1GHz


23/28

Test Mode : Mode 1

Description : Front View of Radiated Emission Test _ Above 1GHz

Test Mode : Mode 1

Description : Back View of Radiated Emission Test _ Above 1GHz


24/28

5 EUT Photograph

(1) EUT Photo

(2) EUT Photo


25/28

(3) EUT Photo

(4) EUT Photo


26/28

(5) EUT Photo

(6) EUT Photo


27/28

(7) EUT Photo

(8) EUT Photo


28/28

Documents

A Test Lab Techno Corp. - APC · A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, ... The above equipment has been tested by A Test Lab Techno Corp., …