A.1.10 - ATI OutdoorsBenelli M4 Raven Deluxe Stock and Forend Package 70.0592.01 B Raven Stock Installation Flip your M4 upside down and with the trigger guard pin still out, take

70.0592.01

Benelli M4 Raven Deluxe Stock and Forend Package

A.1.10.1430

Benelli M4 Raven Stock

Benelli M4 Raven Heatshield

Benelli M4 Raven Mag Tube Picatinny Rail Shroud

Benelli M4 Raven Magazine Cap

Benelli M4 Raven Magazine Tube Extension

Benelli M4 Raven Magazine Follower

Benelli M4 Forend

2

1 3

45

6

7

1

2

3

4

5

6

7


Warning: When handling a firearm, always follow the proper handling procedures at all times. Failure to follow these procedures could result in serious damage, injury, or death. ATI is not responsible for damage to property,

injury, or death resulting from improper installation, misuse or modification of products. If you are not comfortable completing any of the following steps, or do not have the proper tools enlist the help of your

local gunsmith. ATI is not responsible for components that are damaged due to improper installation.

A Stock Removal

!

70.0592.01

[2] 8-32 x 1/4" Button Cap Screw[1] M8 x 1.0 x 25mm Flat Head Socket Cap Screw[1] 6-32 x 7/8" Socket Head Cap Screw[4] 6-32 x 1/4" Socket Head Cap Screw

[1] Benelli Lock Nut

[1] #6 Washer

Allen Set

Torx Set

Punch Set

Benelli 1" Open Face WrenchRaven Lock Nut Tool

Point the shotgun in a safe direction and place the saftey in the "on" position. Next pull back the slide, and carefully inspect the chamber to be sure the shotgun is unloaded.

Begin by pushing the tigger guard take down pin as seen in Figure 1A, (which will come out almost all of the way as seen in Figure 1A) using a small punch.

Next, remove the trigger guard assembly by pulling down on the trigger guard as seen in Figure 2.

Next, unscrew the stock by turning it counterclockwise and remove from the receiver as seen in Figure 3.

1A

1B

3

2

!

1

2

3

1


70.0592.01

B Raven Stock Installation

Flip your M4 upside down and with the trigger guard pin still out, take the trigger assembly and reinstall it into the firearm as seen in Figure 1. To reinstall you will have to hold in the bolt release button and then seat the assembly.

Before installing the ATI Raven Stock to your M4 you will have to remove the buffer tube and the LOP lever from the buttstock. To do this you will unscrew the orange 8/32 x 1/4" button cap screw using a 3/32" allen wrench as seen in Figure 2. Once you have unscrewed the LOP lever you may discard the orange screw.

After unscrewing the LOP lever, pull down and remove the latch from the buttstock as seen in Figure 3 .

Next, remove the buffer tube from the buttstock by sliding it out of the stock body as seen in Figure 4.

3

2

4

1

2

3

4

Bolt Release Button1

2


70.0592.01

Take the pistol grip and place the single point sling adapter as seen in Figure 5A into the front of the pistol grip as seen in Figure 5B. You may place the single point sling adapter into the grip with the sling loop facing out to the right or left side of the pistol grip.

Slide the ATI pistol grip over the bolt spring housing until it is flush with the receiver as seen in Figure 6.

Next, take the provided castle nut and slide it over the bolt spring housing (with the teeth out) all the way into the rear of the pistol grip as seen in Figure 7.

Take the provided castle nut spanner wrench and slide it onto the castle nut as seen in Figure 8A. Engage the teeth with the slots in the castle nut. Next, take the 1" open face wrench provided and tighten the castle nut by turning the castle nut spanner wrench clockwise until tight as seen in Figure 8B.

B Raven Stock Installation -Continued

6

7

5

6

7

8

8A 8B

5A

5B

3


70.0592.01


Next, slide the buffer tube onto the bolt spring housing as seen in Figure 9A and into the rear of the pistol grip as seen in Figure 9B

Take the buffer tube end cap and slide it into the end of the buffer tube as seen in Figure 10A. Make sure that the cap lines up with the groves of the buffer tube and fits snug into the end of the buffer tube as seen in Figure 10B.

Using a 5mm allen wrench, tighten the supplied M8-1.0 x 25mm Flat Head Socket Cap Screw into the end of the buffer tube as seen in Figure 11.

NOTE: Before tightening the M8-1 x 25mm flat head socket cap screw to the buffer tube, apply the provided locktite to the bolt threads and then tighten.

Slide the stockbody onto the buffer tube as seen in Figure 12.

Next, you will reinstall the buttstock LOP lever by snapping it into the bottom of the stock body as seen in Figure 13. The locking pin will need to be aligned with one of the six position adjustment holes when snapping into place.

12

13

9

10

11

12

13

10A 10B

4

9A 9B

11


70.0592.01

Using (2) 8/32 x 1/4" button cap screws and a 3/32" allen wrench tighten the buttstock LOP lever to the bottom of the stock body.

NOTE: One screw will be placed in the front of the LOP lever as seen in Figure 14A and one will be placed in the middle of the LOP lever as seen in Figure 14B.

To adjust the height of the cheekrest, turn the adjustment dial clockwise to raise and counter clockwise to lower until the cheekrest is at the desired height as seen in Figure 15.

To adjust the tension of the slide adjustment of the stock body on the buffer tube, begin by using a T20 torx driver and unscrew the screw under the front of the cheekrest as seen in Figure 16A. Make sure that the stock is extended and the cheekrest is raised fully before unscrewing as seen in Figure 16B.

Next, slide the cheekrest forward and remove it from the stockbody as seen in Figure 17.


14

15

16

17

14A

14B

15

16A 16B

17

5


70.0592.01


Using a 3/8" open face wrench, loosen the two nuts on each side of the stockbody as seen in Figure 18.

Next, use a 3/32"" allen wrench to loosen or tighten the (2) set screws on each side of the stockbody as seen in Figure 19. By loosening or tightening these set screws you will be able to set the tension of the stock on the buffer tube. Adjust all (4) set screws in small increments, testing the tension in between each adjustment of the (4) set screws until the desired tension is achived to insure that the stock slides uniformally on the buffer tube.

After you have the tension of the slide adjustment of the stock set, tighten the 2 nuts on each side of the stockbody using a 3/8" open face wrench, to insure the tension is locked in place as seen in Figure 20. Apply 10 ft/lbs. of torque to the nuts to ensure they do not come loose.

18

19

18

19

20

20

6


70.0592.01

Next, slide the cheekrest back onto the stockbody as seen in Figure 21.

Use a T20 torx driver and tighten the screw in the front of the cheekrest to secure the cheekrest to the stockbody as seen in Figure 22.


21

22

21

22

7


70.0592.01

C Magazine Follower Installation

Begin by unscrewing the magazine end cap and removing from the mag extension as seen in Figure 1.

Next, slide the barrel forward as seen in Figure 2A and remove the barrel from the receiver as seen in Figure 2B. (The forend will detach once the barrel is slid forward).

Unscrew the mag tube and remove it from the firearm as seen in Figure 3.

Using a snap ring pliers, remove the magazine spring retainer as seen in Figure 4A. Be sure to hold onto the spring retainer as the spring is under pressure and will shoot out as seen in Figure 4B.

Remove the magazine spring by pulling it out of the magazine tube. Next, turn the firearm over and remove the stock magazine follower as seen in Figure 5.

1

2B

3

2A

4A 4B

5

1

2

3

4

5

8


70.0592.01

C Magazine Follower Installation -Continued

Place the new magazine follower into the magazine tube as shown in Figure 6A.

Take the magazine spring retainer (removed in step C4) and place in the Raven Mag Tube Extension as seen in Figure 1.

Using a punch, lightly tap the spring retainer as seen in Figure 2A so that the front of the retainer lines up with the shelf in the mag tube extension as seen in Figure 2B.

Place the spring back into the tube as seen in Figure 3.

Take the mag tube extension as seen in Figure 4A and place over the spring. The spring will be under tension as you begin to move the spring back into the tube as seen in Figure 4B.

Tighten the mag tube extension as seen in Figure 5.

6

6

D

1

Mag Tube Extension and Shroud Installation

2

9

1

2A

3

4A

4B

3

4

2B

5

5


70.0592.01

D Mag Tube and Shroud Installation -Continued

Next, slide the barrel over the mag tube extensions leaving as seen in Figure 6.

After re-installing the barrel, slide the mag tube shroud into place as seen in Figure 7A making sure to leave about 1/2" gap between the barrel and receiver as seen in Figure 7B.

Using the provided 6-32 x 7/8 Socket Head Cap Screw and a 7/64" allen wrench turn the screw 3-4 rotations but do not tighten all the way as seen in Figure 8.

Begin by seating the left forend rim against the barrel as seen in Figure 1A, making sure that the barrel lug is behind the rim as seen in Figure 1B. Repeat this process for the right forend rim.

7A

8

E Forend Installation

1

1A

1B

10

7B

6

6

7

8


70.0592.01

E Forend Installation -Continued

Slide the forend body into the front of the left and right forend rims as seen in Figure 2.

Next, take the forend rims and spread the rear forend rims apart as seen in Figure 3A and seat the forend down against the barrel. You can now press the forend rims together around the forend as seen in Figure 3B.

Take the magazine tube cap and tighten onto the mag tube extension as seen in Figure 4A. Once the cap is tight, the forend should seat to the receiver as seen in Figure 4B.

2

3A

3B

4A

4B

2

3

4

11


70.0592.01

E Forend Installation -Continued

Once the barrel is seated into the receiver you can than tighten the mag tube shroud ( that you began to tighten in Step D4 ) the rest of the way as seen in Figure 5.

Begin by placing the (4) provided 6-32 x 1/4" Socket Head Cap Screws into the feet of the heatshied as seen in Figure 1A and place the heatshield onto the top of forend making sure to line up the feet of the heatshield with the slots on the forend as seen in Figure 1B.

Using a 7/64 allen wrench tighen the 6-32 x 1/4" Socket Head Cap Screws to the forend as seen in Figure 2 .

5

5

F Heatshield Installation

1A

1B

2

1

2

12


70.0592.01

F Heatshield Installation -Continued

Take the rubber forend inserts as seen in Figure 3A and install into the slots as seen in Figure 3B.NOTE: The two front plugs have a straight front as seen and may be installed in either side. The two rear plugs will be tappered and will be installed in the appropriate side with the tappered side facing the rear .

Your Benelli M4 Raven Deluxe Stock and Forend Package is now complete.

REAR PLUGS3

FRONT PLUGS

RIGHT SIDE LEFT SIDE

13

Documents

A.1.10 - ATI OutdoorsBenelli M4 Raven Deluxe Stock and Forend Package 70.0592.01 B Raven Stock Installation Flip your M4 upside down and with the trigger guard pin still out, take