Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
A11.15
A11
TURN-TILT WINDOWS
HANDLES ANDLOCKCASES
01.11.2019
Waregemstraat 5 - 9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - [email protected] - www.sobinco.com
CONTENTS
1. Lockcases n° 35000-720 and 35300-720 .......................... A11.15.031.1. Characteristics A11.15.031.2. Assembly A11.15.041.3. Milling A11.15.06
2. Handles without base ......................................................... A11.15.072.1. General A11.15.072.2. Edge handles A11.15.072.3. Horizon handles A11.15.082.4. Covers n° 30000-670-3 and 30000-670-4 A11.15.08
3. Lockcases n° 35000-721 and 35300-721 .......................... A11.15.093.1. Characteristics A11.15.093.2. Assembly and milling A11.15.10
4. Handles with square spindle of 7 mm .................................A11.15.114.1. Edge handles A11.15.114.2. Horizon handles A11.15.154.3. Sobinox handles A11.15.16
5. Connection piece sets ..........................................................A11.15.195.1. Connection piece set n° 35000-700 A11.15.195.2. Connection piece set n° 35300-701 (Chrono Safe) A11.15.19
6. Handles with fork ................................................................ A11.15.206.1. Standard handles A11.15.206.2. Handles with cylinder (CYL version) A11.15.226.3. Fireman’s axe handle (V version) and loose grip A11.15.246.4. Handles with key (W version) A11.15.256.5. Handles with long fork A11.15.266.6. Handles with sloping base A11.15.276.7. Standard and ‘S’ handle A11.15.296.8. Handle preparations for handles with fork A11.15.296.9. Reinforcement piece n° 30000-691 and -692 A11.15.30
7. Edge* Polaris handles ......................................................... A11.15.31
A11.15.02 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
1. Lockcases n° 35000-720 and 35300-7201.1. Characteristics
• Lockcases n° 35000-720 and 35300-720 can be used with the handles without base.
• The lockcases are made entirely of non-corroding materials.
• The installation is only possible for vents over 685 mm high.
• Lockcase n° 35000-720 can be used for Chrono Standard and Chrono Plus.
• The set n° 35300-720 for Chrono Safe consists of a lockcase n° 35000-720 and a thickness piece n° 30340-632-1.
Profile dimensions
N° 35000-72035000-720
Lockcase n° 35000-7201 35000-720 lockcase
N° 35300-720(Chrono Safe)
30340-632-1
35000-720
Set n° 35300-7201 30340-632-1 thickness piece1 35000-720 lockcase
CHRONO TURN-TILT WINDOWS A11.15.03
HANDLES AND LOCKCASES
A11.15
1.2. Assembly
Check: has the milling been deburred?
Tilt the lockcase behind the last tooth of the profile.
Click in the handle without base.
1
Mount the base with the 2 enclosed screws.2
Connection withthe Chrono rods
3
Check this position
Handle n° 30000-67x
CLICK
4 Check:Check the tightness of the grip within 8 hours after clicking in the grip.Therefore turn the handle to all positions several times and move the grip firmly from front to back in each position.In case of wrong assembly internal damage can occur after 8 hours.
A11.15.04 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
Assembly in closed position
Use of a temporary handle n° 30000-957 or n° 30000-670-5
• The building site handle is assembled awaiting the final handle.
• The handle is assembled and disassembled in the same way as the final handle.
• The handle can be used for the assembly of the fittings with the intention to transport the window afterwards without the final handle.
• The use of the assembly handle should be restricted to maximum 8 hours because otherwise internal damage can occur.
Check this positionCLICK
Assembly handlen° 30000-670-5
Building site handlen° 30000-957
OR
CHRONO TURN-TILT WINDOWS A11.15.05
HANDLES AND LOCKCASES
A11.15
1.3. Milling
1st milling 2nd milling
Minimum 6 mm deep With width B + 1 mm at distance 5.5 mm
1.3.1. Disassembly
Turn the handle in the horizontal position (90°).
Press with a small tool in the cavity.
L=21.5 mm → C=16.2 mmL=22 mm → C=16.7 mm
1 2
A11.15.06 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
2. Handles without base2.1. General
• The Edge handles n° 30000-673 (CYL), -674 and the Horizon handles n° 30000-670 (CYL), -671 have the same design as the corresponding door handles. So these handles can be used next to one another with the advantage of having the same appearance.
• The high security system Chrono Safe must always be operated by cylinder locking handles. The cylinder locking handle can be locked in closed position.
• To use with Chrono lockcase n° 35000-720 and n° 35300-720 (only CYL version).
• Finish: - N° 30000-670, n° 30000-673: Grip in aluminium and base in zinc alloy, always polyester powder coated in more than 450 RAL colours.
- N° 30000-670CYL, n° 30000-671, n° 30000-673CYL, n° 30000-674: Grip in aluminium and base in zinc alloy, grip anodised or grip and base polyester powder coated in more than 450 RAL colours.
2.2. Edge handles
N° 30000-673 N° 30000-674 N° 30000-673CYL
Spindle length 24.5 mm
Spindle length 24.5 mm
Spindle length 24.5 mm
CHRONO TURN-TILT WINDOWS A11.15.07
HANDLES AND LOCKCASES
A11.15
2.3. Horizon handles
2.4. Covers n° 30000-670-3 and 30000-670-4• Covers to click on the base to protect the windows during
transport.
• Suitable for each handle without base.
• The cover can be removed by turning it with a screwdriver.
• Versions: - N° 30000-670-3: standard version in black synthetic material - N° 30000-670-4: coated version in synthetic material
N° 30000-670 N° 30000-671 N° 30000-670CYL
Spindle length 24.5 mm
Spindle length 24.5 mm
Spindle length 24.5 mm
A11.15.08 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
3. Lockcases n° 35000-721 and 35300-7213.1. Characteristics
• Lockcases n° 35000-721 and 35300-721 can be used by a handle with square spindle of 7 mm. The lockcases can be operated by the Edge, Horizon and Sobinox handles.
• The lockcases are made entirely of non-corroding materials.• The installation is only possible for vents over 685 mm high.
• Lockcase n° 35000-721 can be used for Chrono Standard and Chrono Plus.
• The set n° 35300-721 for Chrono Safe consists of a lockcase n° 35000-721 and a thickness piece n° 30340-632-1.
Profile dimensions
Lockcase n° 35000-7211 35000-721 lockcase
N° 35000-72135000-721
Set n° 35300-7211 30340-632-1 thickness piece1 35000-721 lockcase
N° 35300-721(Chrono Safe)
30340-632-1
35000-721
CHRONO TURN-TILT WINDOWS A11.15.09
HANDLES AND LOCKCASES
A11.15
3.2. Assembly and milling
a) Press the clamping plate and the lockcase together.b) Tilt the lockcase behind the last tooth of the profile.c) Release the clamping plate. The locking rollers at front
side are clicking into the holes.
3
(1) Not included
L = 22 → B = 16L = 21.5 → B = 15.5
1
One milling up to depth A
Connection with Chrono rods
2
A11.15.10 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
4. Handles with square spindle of 7 mm4.1. Edge handles
General• To use with Chrono lockcase n° 35000-721 and n° 35300-721 (only lockable versions).
• Versions: - standard handle - handle, lockable by cylinder (CYL) - handle, lockable by push button (KNOB)
• All handles are non-handed.
• Suitable for aluminium, wood and PVC.
• The Edge handles have the same design as the Edge door handles. So these handles can be used next to one another with the advantage of having the same appearance.
• Finish: - N° 35000-682-xx, 35300-682-xxCYL, 35300-682-xxKNOB: grip and base plate cover in aluminium, base in zinc alloy, always polyester powder coated in more than 450 RAL colours.
- N° 30000-682-..: grip and base in aluminium, anodised or polyester powder coated in more than 450 RAL colours.
Standard handle n° 35000-682-xx
• The handle has been tested in accordance with the European standard EN13126-3:2012 and obtained the following classification code:
Order code Spindle length L35000-682-25 25 mm35000-682-38 38 mm
Categoryof use
Durability MassFire
resistanceSafety
Corrosionresistance
SecurityApplication
partTestsizes
1 4/180 - 0 1 4 0 3/C1 -
CHRONO TURN-TILT WINDOWS A11.15.11
HANDLES AND LOCKCASES
A11.15
Handle with cylinder n° 35300-682-xxCYL• The handle can be locked in closed position (0°) and in tilt position (180°).
• The handle has been tested by SKG, 3 stars. Attention: the certificate expires when you order in mill finish!
• The handle has been tested in accordance with the European standard for anti-burglary windows EN1627-1630 (class RC1-6) and has a tested break moment of 100 Nm.
• The handle has been tested in accordance with the European standard EN13126-3:2012 and obtained the following classification code:
Order code Spindle length L35300-682-25CYL 25 mm35300-682-38CYL 38 mm
Categoryof use
Durability MassFire
resistanceSafety
Corrosionresistance
SecurityApplication
partTestsizes
1 4/180 - 0 1 4 2/2 3/C1 -
A11.15.12 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
Handle with push button n° 35300-682-xxKNOB• The handle locks automatically in closed position (0°) and in tilt position (180°) by means of a push button
operated cylinder.
• The handle is unlocked by pushing the button. Then the handle can be turned.
• The handle has been tested in accordance with the European standard for anti-burglary windows EN1627-1630 (class RC1-6) and has a tested break moment of 100 Nm.
• The handle has been tested in accordance with the European standard EN13126-3:2012 and obtained the following classification code:
Order code Spindle length L35300-682-25KNOB 25 mm35300-682-38KNOB 38 mm
Categoryof use
Durability MassFire
resistanceSafety
Corrosionresistance
SecurityApplication
partTestsizes
1 4/180 - 0 1 4 2/1 3/C1 -
CHRONO TURN-TILT WINDOWS A11.15.13
HANDLES AND LOCKCASES
A11.15
Variant handle n° 30000-682• Only available as standard version.
Profile preparations• See drawing:
• In combination with the lockcase n° 35000-721 or n° 35300-721: see profile preparations for lockcase.
Installation order1. Put the handle in turn position.2. Pull the base plate cover and turn it 90°.3. Fix the handle with screws M5.4. Turn the cover 90° and clip it on the base.
Order code Spindle length L30000-682 25 mm30000-682-38 38 mm
A11.15.14 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
4.2. Horizon handles
Horizon handle n° 30000-680• The Horizon handles have the same design as the Horizon door handles. So these handles can be used
next to one another with the advantage of having the same appearance.
• Only available as standard version.
• To use with Chrono lockcase n° 35000-721.
• Finish: grip and base in aluminium, anodised or polyester powder coated in more than 450 RAL colours.
Profile preparations and installation order• Similar to the Edge handles.
Order code Spindle length L30000-680 25 mm30000-680-38 38 mm
CHRONO TURN-TILT WINDOWS A11.15.15
HANDLES AND LOCKCASES
A11.15
4.3. Sobinox handles
General• The Sobinox handles are manufactured from high-grade stainless steel AISI 304 and are supplied with
a satin finish.• These door handles can be used in many different sectors due to their aesthetic, practical, maintenance
friendly and hygienic properties: e.g. private houses, hospitals, catering, industry, ... .• The grips are available in different types and can be supplied with an oval or rectangular short backplate. • The window handles are supplied with a steel zinc plated square spindle of 7 mm. Available in lengths of
25 and 38 mm.• Window handles with cylinder (1852CYL and 1857CYL) are also available. When ordering please add CYL
at the order code.• The following stainless steel window handles are also available in an aluminium version (AL).
Finish aluminium version: anodised or polyester powder coated in more than 450 RAL colours. - 1850AL - 1852AL - 1855AL - 1857AL
• To be used in combination with: - Chrono lockcase n° 35000-721: see page A11.15.09. - Chrono Safe lockcase n° 35300-721: see page A11.15.09. - for turn-tilt, tilt-turn, side hung open in as well as for tilt windows.
Maintenance instructions• Maintenance should be carried out at suitable intervals to prevent surface corrosion and for reasons of
hygiene.• Normal maintenance:
- Clean the stainless steel parts regularly. - Treat the surface with soapy water or with a mild detergent. - Rinse of the detergent with clean water. - Polish with a soft cloth or sponge.
• Never use: - Scouring powders. - Steel wool or steel brushes. - Highly abrasive materials.
Fixing backplate with cover
A11.15.16 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
Handles with oval backplate
n° 1850(AL)-25 n° 1851-25n° 1850(AL)-38 n° 1851-38
n° 1852(AL)-25 n° 1752-25n° 1852(AL)-38 n° 1752-38
n° 1853-25 n° 1852CYL-25n° 1853-38 n° 1852CYL-38
• Handles n° 1852CYL-25 and 1852CYL-38 are suitable for turn-tilt, tilt-turn, side hung open in and tilt windows.
CHRONO TURN-TILT WINDOWS A11.15.17
HANDLES AND LOCKCASES
A11.15
Handles with rectangular backplate
n° 1855(AL)-25 n° 1856-25n° 1855(AL)-38 n° 1856-38
n° 1857(AL)-25 n° 1757-25n° 1857(AL)-38 n° 1757-38
n° 1858-25 n° 1857CYL-25n° 1858-38 n° 1857CYL-38
• Handles n° 1857CYL-25 and 1857CYL-38 are suitable for turn-tilt, tilt-turn, side hung open in and tilt windows.
A11.15.18 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
5. Connection piece sets5.1. Connection piece set n° 35000-700
5.2. Connection piece set n° 35300-701 (Chrono Safe)
• Note: use of fixing holes 84 mm, 98 mm and 104 mm. In this case the fixing blocks for the connection piece must be mounted after fixing the handle because it must still be possible to slide the connection piece to fix the handle.
Connection piece set n° 35000-7002 30000-690 screw1 30000-700 connection piece
Connection piece set n° 35300-7012 30000-690 screw1 30300-701-1 connection piece2 30300-701-2 block connection piece1 30340-631-1 thickness piece
CHRONO TURN-TILT WINDOWS A11.15.19
HANDLES AND LOCKCASES
A11.15
6. Handles with fork• The non-locking handles (without cylinder) have been tested in accordance with the
European standard EN13126-3:2012 and obtained the following classification code:
• The cylinder locking handles (CYL) have been tested in accordance with the European standard EN13126-3:2012 and obtained the following classification code:
6.1. Standard handles• The same handles can be used for tilt-turn, side hung and bottom hung open in windows. So these
windows can be used next to one another with the advantage of having the same appearance.
• Finish: - n° 30000-662, n° 30000-659 and n° 30000-657: grip in aluminium and base in zinc alloy, always polyester powder coated.
- n° 30000-655 and n° 30000-654: grip and base in aluminium anodised or polyester powder coated. - more than 450 RAL colours.
• Fixing holes: see page A11.15.29.
Categoryof use
Durability MassFire
resistanceSafety
Corrosionresistance
SecurityApplication
partTestsizes
1 5/180 - 0 1 4 0 3/C2 -
Categoryof use
Durability MassFire
resistanceSafety
Corrosionresistance
SecurityApplication
partTestsizes
1 5/180 - 0 1 4 2/2 3/C2 -
N° 30000-662
Throw X = 34 mm
N° 30000-659
Throw X = 34 mm
A11.15.20 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
N° 30000-655
Koers X = 34 mm
N° 30000-657
Throw X = 34 mm
N° 30000-654
Throw X = 34 mm
CHRONO TURN-TILT WINDOWS A11.15.21
HANDLES AND LOCKCASES
A11.15
6.2. Handles with cylinder (CYL version)• The high security system Chrono Safe must always be operated by cylinder locking handles n° 30000-...CYL.
• The cylinder locking handle can be locked in closed and tilt position.
• The same handles can be used for tilt-turn, side hung and bottom hung open in windows. So these windows can be used next to one another with the advantage of having the same appearance.
• Finish: - n° 30000-662CYL, n° 30000-659CYL and n° 30000-657CYL: grip in aluminium and base in zinc alloy, always polyester powder coated.
- n° 30000-655CYL and n° 30000-654CYL: grip and base in aluminium anodised or polyester powder coated.
- more than 450 RAL colours.
• Fixing holes: see page A11.15.29.
Throw X = 34 mm
N° 30000-662CYL N° 30000-659CYL
Throw X = 34 mm
A11.15.22 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
N° 30000-657CYL
Throw X = 34 mm
N° 30000-655CYL
Throw X = 34 mm
N° 30000-654CYL
Throw X = 34 mm
CHRONO TURN-TILT WINDOWS A11.15.23
HANDLES AND LOCKCASES
A11.15
6.3. Fireman’s axe handle (V version) and loose grip
N° 30000-659V N° 30000-657V
• The same handles can be used for tilt-turn, side hung and bottom hung open in windows. So these windows can be used next to one another with the advantage of having the same appearance.
• Finish: - handle n° 30000-659V and -657V in zinc alloy, always polyester powder coated. - handle n° 30000-655V and loose grip n° 505 in aluminium anodised or polyester powder coated. - more than 450 RAL colours.
• Fixing holes: see page A11.15.29.
• This version is especially suitable in places where only authorized persons can open the windows (by means of the loose grip n° 505), but in case of fire the square pointed end of a fireman’s axe can also operate the handle.
N° 30000-655V N° 505
Throw X = 34 mm Throw X = 34 mm
Throw X = 34 mm
A11.15.24 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
6.4. Handles with key (W version)
N° 30000-659W N° 30000-657W
• The same handles can be used for tilt-turn, side hung and bottom hung open in windows. So these windows can be used next to one another with the advantage of having the same appearance.
• Finish: - handle n° 30000-659W and -657W in zinc alloy, always polyester powder coated. - handle n° 30000-655W in aluminium anodised or polyester powder coated. - more than 450 RAL colours.
• Fixing holes: see page A11.15.29.
• This version must to be operated with the special key n° 505W. With the key, the handle can be easily operated.
N° 30000-655W N° 505W
Throw X = 34 mm Throw X = 34 mm
Throw X = 34 mm
CHRONO TURN-TILT WINDOWS A11.15.25
HANDLES AND LOCKCASES
A11.15
6.5. Handles with long fork
• The handles with longer fork are available in 5 types:
• Besides the dimension X, the profiles must meet a number of profile requirements to obtain a good installation of the fittings. The required profile dimensions can be found on page A11.11.03.
• The same handles can be used for tilt-turn, side hung and bottom hung open in windows. So these windows can be used next to one another with the advantage of having the same appearance.
• The handles are also available in V-, W-, S- and CYL version.
• Fixing holes: see page A11.15.29.
Handles with long fork
Length forkL (mm)
Distance between
frame and ventX (mm)
30000-654 30000-655 30000-657 30000-659 30000-662 21.3 7-10
4000-214 4000-215 4000-217 4000-219 - 24.5 10-13
30000-654-26 30000-655-26 30000-657-26 30000-659-26 30000-662-26 26 12-15
30000-654-29 30000-655-29 30000-657-29 30000-659-29 30000-662-29 29 15-18
30000-654-32 30000-655-32 30000-657-32 30000-659-32 30000-662-32 32 18-21
30000-654-35 30000-655-35 30000-657-35 30000-659-35 30000-662-35 35 21-24
30000-654-38 30000-655-38 30000-657-38 30000-659-38 30000-662-38 38 24-27
A11.15.26 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
6.6. Handles with sloping base
Characteristics
• The handles with sloping base are used in situations where the frame profile obstructs the grabbing of the grip.
• General characteristics: see page A11.15.20.
• The base is provided with 2 hook-in pins which engage into the profile in order to have a solid fixing.
• Also available as cylinder locking handle (CYL).
• The handle is only available as type ‘S’ with the fixing holes at a distance of 98 mm.
• Handle preparations: see next page.
Handles n° 30000-663S and n° 30000-663SCYL
N° 30000-663S N° 30000-663SCYL
CHRONO TURN-TILT WINDOWS A11.15.27
HANDLES AND LOCKCASES
A11.15
Handles n° 30000-660S and n° 30000-660SCYL
Handle preparations
N° 30000-660S N° 30000-660SCYL
Drill holes forhook-in pins
A11.15.28 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
6.7. Standard and ‘S’ handle
6.8. Handle preparations for handles with fork
• A drilling jig n° 4000-396 is available for the handle cut-out.
Handle type ‘S’Standard version
Standard version Handle type ‘S’
CHRONO TURN-TILT WINDOWS A11.15.29
HANDLES AND LOCKCASES
A11.15
6.9. Reinforcement piece n° 30000-691 and -692
• The reinforcement pieces produce a more solid fixing of the handle.
• This piece serves as a clamping plate and prevents deformation of the profile wall or in extreme situations prevents the fixing screws being pulled through profiles with thin walls.
• Choice between 2 pieces depending on fixing hole configuration: - N° 30000-691: standard handle - N° 30000-692: handle type ‘S’
• Note: only the fixing holes at 82 mm and 84 mm are possible in combination with the Chrono Safe connection piece.
• Installation: see example.
N° 30000-692N° 30000-691
Reinforcement piece
A11.15.30 CHRONO TURN-TILT WINDOWS
HANDLES AND LOCKCASES
A11.15
7. Edge* Polaris handlesGeneral
• On request, a number of Edge handles can be provided with gemstones in 4 different patterns.
• The patterns apply to every Edge handle.
• Not possible for handles with cylinder.
• The gemstones are possible in white and blue.
• Example: handle without base.
Patterns
Encoding
Example: 30000-673-SW10
Pattern: - 0: 1 gemstone - 1: 3 gemstones (triangle) - 2: 3 gemstones - 3: 5 gemstones
Gemstone colour: - 1: white - 2: blue
Swarovski
Handle number
Pattern 0 Pattern 1 Pattern 2 Pattern 3
CHRONO TURN-TILT WINDOWS A11.15.31
HANDLES AND LOCKCASES
A11.15