A318/A319/A320/A321 31700 BLAGNAC

A318/A319/A320/A321SERVICE BULLETIN

CONFIG 001

REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19 Page 1

CONF 001AIRBUS2, ROND POINT EMILE DEWOITINE31700 BLAGNACFRANCE The content of this document is the property of Airbus.It is supplied in confidence and commercial security on its contents must be maintained.It must not be used for any purpose other than that for which it is supplied, nor may informationcontained in it be disclosed to unauthorized persons.It must not be reproduced in whole or in part without permission in writing from the owners of thecopyright. Requests for reproduction of any data in this document and the media authorized for it mustbe addressed to Airbus.

ATA SYSTEM: 25

TITLE: EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGE COMPARTMENTS -REVISE BIN BASE FOR PIVOTING OHSC

MODIFICATION No.:162563K30846


CONFIG 001 REVISION TRANSMITTAL SHEET


ATA SYSTEM: 25


REVISION TRANSMITTAL SHEETThis page transmits Revision No. 01 of Service Bulletin No. A320-25-1BPV.A. ADDITIONAL WORK

No additional work is required by this revision.B. REASON

Revision No. 01 issued to amend a PN in KIT D01.C. CHANGES

MATERIAL INFORMATIONLIST OF NEW PARTS

Part kit 251BPVD01R03 Part Number amended to enable kit deliveryACCOMPLISHMENT INSTRUCTIONSTask set A320-A-25-XX-1BPV-01000-93AA-A Replacement of the Bin in the PivotingOverhead Stowage Compartment

PROCEDUREA320-A-25-XX-1BPV-01001-920A-A Replace the Bin ofthe Pivoting OverheadStowage Compartment(OHSC)

Bin 2FR EE STIFF added

D. FILING INSTRUCTIONSThis Service Bulletin has been generated electronically and is reissued as a completedocument. Replace the complete document.Put this Revision Transmittal Sheet in front of the Service Bulletin.

E. HISTORY OF PREVIOUS REVISIONSNo previous revision

F. REVISION SEQUENCEORIGINAL: May 27/19REVISION No. : 01 - Jun 27/19


CONFIG 001 SUMMARY


ATA SYSTEM: 25


SUMMARYThis summary is for information only and is not approved for modification of the aircraft.A. MODIFICATIONS

MODIFICATION CLASSIFICATIONMAJOR NoneMINOR 162563K30846

NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on themass, balance, structural strength, reliability, operational characteristics affectingthe airworthiness of the product. All other changes are major changes.

B. REASON

(1) HistorySeveral damages to the pivoting bins of the Overhead Stowage Compartments (OHSC)have been reported in-service leading to unscheduled and additional maintenance.

(2) Objective/ActionThis Service Bulletin is published to advise the operators of the affected MSNs toinstall new pivoting bins which provide a more robust bonding design.

(3) AdvantagesThe accomplishment of this Service Bulletin will improve the robustness and increasethe lifetime of the pivoting OHSCs leading to a reduction in unscheduled maintenance.

(4) Operational/Maintenance ConsequencesNone

C. GENERAL EVALUATION

EVALUATION TABLECOMPLIANCE RECOMMENDED COST SAVING NOA/C OPERATIONAFFECTED

NO VENDOR SB NO

CANCELS INSPECTION SB NO ETOPS AFFECTED NOPAX COMFORT AFFECTED YES POTENTIAL AD NORELIABILITY AFFECTED NO STRUCTURAL LIFE EXTENSION NOLIFE LIMIT NO LINE MAINTENANCE AFFECTED NO

NOTE: Service Bulletin recommended to be accomplished to prevent significantoperational disruptions.

D. MAINTENANCE CONFIGURATIONNo specific aircraft maintenance configuration required.

E. MATERIAL PRICE INFORMATION


CONFIG 001 SUMMARY


(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment(a) Task set A320-A-25-XX-1BPV-01000-93AA-A Replacement of the Bin in the

Pivoting Overhead Stowage Compartment

MATERIAL PRICE INFORMATION TABLE

MATERIAL SET QTYPER A/C PRICE PER A/C MAIN PARTS

Part kit 251BPVD01R03 1 539000.00 USD Bin assembliesPart kit 251BPVD05R01 1 60.00 USD Washers and screwsTOTAL 539060.00 USD Components See SB See Note Brackets

NOTE: Price information to be obtained from the given supplier.

F. APPLICABILITYThis Service Bulletin is applicable to this (these) operator(s):ACA DAL LAN TCX

G. CONCURRENT REQUIREMENTSAccomplishment of this Service Bulletin requires the prior or simultaneous accomplishmentof the following Service Bulletin:

Service Bulletin(s) Modification(s)Ref. SB A320-25-1BPW

NOTE: Ref. SB A320-25-1BPW (EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGECOMPARTMENTS - REVISE INSTALLATION OF DAMPENER FOR POHSC BINS).

H. NATURE OF THE WORK



AIRCRAFT NOEQUIPMENT YES

I. MANPOWER



MANPOWERTOTAL MAN-HOURS 35.50 hELAPSED TIME (HOURS) 21.00 h


CONFIG 001 SUMMARY

Figure ICN-A320-A-25XX1BPV-A-FAPE3-00YY5-A-001-01 SHEET 1/1REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19

General overviewPage 5

J. GENERAL OVERVIEWCONF 001

Z200

A

TYPICAL

OVERHEAD STOWAGE COMPARTMENTTO BE MODIFIED

A

ICN-A320-A-25XX1BPV-A-FAPE3-00YY5-A-001-01


CONFIG 001


ATA SYSTEM: 25


1. PLANNING INFORMATIONA. APPLICABILITY

NOTE: An accomplishment Overhead Stowage Compartment (OHSC) per OHSC is allowed.

(1) ModelsON A/C 06923, 07031, 07061, 07112, 07149, 07165, 07214, 07233, 07268, 07281, 07293,07304, 07327, 07364, 07373, 07381, 07436, 07441, 07479, 07546, 07592, 07672, 07707,07709, 07765, 07777, 07840, 07845, 07885, 07896, 07943, 07973, 08026, 08036, 08040,08063, 08078, 08080, 08128, 08134, 08159, 08171, 08180, 08191, 08200, 08207, 08227,08233, 08250, 08251, 08258, 08279, 08283, 08316, 08322, 08332, 08339, 08359, 08370,08388, 08423, 08447, 08502, 08530, 08536, 08694, 08695, 08697, 08713, 08734, 08763,08765, 08809, 08810, 08812, 08822, 08854, 08856, 08858, 08859, 08914-08916, 08974,08975, 09025, 09027, 09028, 09066

321-211CONF 001

(2) MSN by configuration

MSN CONFIGURATION06923 07031 07061 07112 07149 07165 07214 07233 0726807281 07293 07304 07327 07364 07373 07381 07436 0744107479 07546 07592 07672 07707 07709 07765 07777 0784007845 07885 07896 07943 07973 08026 08036 08040 0806308078 08080 08128 08134 08159 08171 08180 08191 0820008207 08227 08233 08250 08251 08258 08279 08283 0831608322 08332 08339 08359 08370 08388 08423 08447 0850208530 08536 08694 08695 08697 08713 08734 08763 0876508809 08810 08812 08822 08854 08856 08858 08859 0891408915 08916 08974 08975 09025 09027 09028 09066

001

(3) Configuration definitionConfiguration 001

CONF 001 is applicable for all DAL01 aircraft affected by this Service Bulletin.CONF 001 retrofits following modifications: 162563K30846.

B. CONCURRENT REQUIREMENTSAccomplishment of this Service Bulletin requires the prior or simultaneous accomplishmentof the following Service Bulletin:

Service Bulletin(s) Modification(s)Ref. SB A320-25-1BPW

NOTE: Ref. SB A320-25-1BPW (EQUIPMENT/FURNISHINGS - OVERHEAD STOWAGECOMPARTMENTS - REVISE INSTALLATION OF DAMPENER FOR POHSC BINS).

C. REASON


CONFIG 001


(1) HistorySeveral damages to the pivoting bins of the Overhead Stowage Compartments (OHSC)have been reported in-service leading to unscheduled and additional maintenance.

(2) Objective/ActionThis Service Bulletin is published to advise the operators of the affected MSNs toinstall new pivoting bins which provide a more robust bonding design.

(3) AdvantagesThe accomplishment of this Service Bulletin will improve the robustness and increasethe lifetime of the pivoting OHSCs leading to a reduction in unscheduled maintenance.

(4) Operational/Maintenance ConsequencesNone

D. DESCRIPTIONTo accomplish this Service Bulletin it is necessary to:(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPV-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment1 Replace the Bin of the Pivoting Overhead Stowage Compartment (OHSC)2 Reidentify the Overhead Stowage Compartment Assemblies

E. COMPLIANCE

(1) ClassificationRECOMMENDED: Service Bulletin recommended to be accomplished to preventsignificant operational disruptions.

(2) Accomplishment TimescaleAccomplishment of this Service Bulletin is recommended at the earliest opportunitywhere manpower and facilities are available.

F. APPROVALThe technical content of this document is approved under the authority of DesignOrganisation Approval No. EASA.21J.031.If an aircraft listed in the applicability has a modification or repair embodied that is notof AIRBUS origin, and which affects the content of this Service Bulletin, the operatoris responsible for obtaining approval by its airworthiness authority for any adaptationnecessary before incorporation of the Service Bulletin.

G. MANPOWERThe manpower estimates given in this Service Bulletin are based on the direct labor cost todo the work. These estimates assume that the work will be done by experienced personnel,and may need to be revised upwards to suit operator’s circumstances. The estimates do notinclude the time to prepare, plan or inspect the work. Manufacture and procurement of partsand tools, drying times for paints, sealants, etc., and general administration work are alsonot included.(1) Replacement of the Bin in the Pivoting Overhead Stowage Compartment

(a) Task set A320-A-25-XX-1BPV-01000-93AA-A Replacement of the Bin in thePivoting Overhead Stowage Compartment

PREPARATION


CONFIG 001


Job Set-up 0.25 hPROCEDURE

Replace the Bin of the Pivoting Overhead StowageCompartment (OHSC)

29.00 h

Reidentify the Overhead Stowage CompartmentAssemblies

3.00 h

PREPARATION FOR TESTNone

TESTOperational Test 3.00 h

CLOSE-UPClose-up 0.25 h

TOTAL MAN-HOURS 35.50 hELAPSED TIME (HOURS) 21.00 h

H. WEIGHT AND BALANCEThe weight and balance estimates given in this Service Bulletin are based on theManufacturer's Empty Weight (MEW) and do not include operator's items. The definition ofMEW and operator's items is given in the Weight and Balance Manual (WBM), Ref. WBM.Manufacturer's Empty Weight +41.5 kg (+91.491 lb)Effect on Balance +962.7 kg.m (+6963.209 lb.ft)

I. ELECTRICAL LOAD DATANot changed

J. REFERENCES

CONCURRENT SERVICE BULLETIN (SB)A320-25-1BPW



AIRCRAFT MAINTENANCE MANUAL (AMM)06-20-00, Page Block 001 Task 12-34-24-869-802Task 24-42-00-861-001 Task 25-24-00-710-002Task 25-24-41-000-802Task 25-24-41-400-802

ELECTRICAL STANDARD PRACTICES MANUAL (ESPM)20-55-00

WEIGHT AND BALANCE MANUAL (WBM)STANDARDS MANUAL (SM)CONSUMABLE MATERIAL LIST (CML)

K. PUBLICATION AFFECTED


CONFIG 001


AIRCRAFT MAINTENANCE MANUAL (AMM)ILLUSTRATED PART CATALOG (IPC)

L. INDUSTRY SUPPORT INFORMATIONAIRBUS will share the costs of accomplishment of this Service Bulletin by providing the kitsat no charge for orders placed before May 30/22.AIRBUS will credit the man-hours indicated in this Service Bulletin at the agreed in-housewarranty labor rate for claims received no later than 90 days after completion of the lastaffected aircraft of your fleet, for the accomplishment of this Service Bulletin before May30/22.


CONFIG 001


2. MATERIAL INFORMATIONA. MATERIAL APPLICABILITY

Material for task set A320-A-25-XX-1BPV-01000-93AA-A Replacement of the Bin inthe Pivoting Overhead Stowage Compartment

MATERIAL QTY SEE NOTESConsumables See SBPart kit 251BPVD01R03 1Part kit 251BPVD05R01 1Components See SBInterchangeable parts See SBSpare parts See SB

B. TOOLINGNo tools

C. CONSUMABLESConsumables for task set A320-A-25-XX-1BPV-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

ITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

D. LIST OF NEW PARTSPart kit 251BPVD01R03

Cost 539000.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected] availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.

Procurement address D4296

AIRBUSMaterial, Logistics and Suppliers ATP II B,Hein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.


CONFIG 001


They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTESE2529795000000 6 CMPRTMNTE2529795000100 5 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 7 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 3 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 1 CMPRTMNTE2529795000800 2 CMPRTMNTE2529795000900 1 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795001800 1 CMPRTMNTE2529795300000 1 CMPRTMNTE2529795300100 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNTE2529795700000 1 CMPRTMNTE2529795700200 1 CMPRTMNTE2529795700500 1 CMPRTMNTE2529796300100 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796600000 1 CMPRTMNTE2529796600100 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529796600300 2 CMPRTMNTE2529797000000 1 CMPRTMNTE2529797000400 1 CMPRTMNTE2529797000600 2 CMPRTMNT

Part kit 251BPVD05R01

Cost 60.00 USDAvailability 150 d (calendar days from receipt of order)NOTE(S)

The sales terms (costs and availability) are estimated in relation to economicconditions. The latest valid price and lead-time for ordering purposes shall beobtained through the AirbusSpares portal or through a request for quotation [email protected].


CONFIG 001


The availability given above is the standard lead-time from the date of your purchaseorder. If items are required before this time, please include a retrofit planningschedule with your order so that we can try to comply with your requirements.


AIRBUSMaterial, Logistics and Suppliers ATP II B,Hein-Sass-Weg 2421129 HAMBURGGERMANYPhone: +49 40 743 51660E-mail: [email protected]: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.Parts listed below can be delivered as a complete and certified kit from Airbus.They can be also delivered as single part items with single part certification directlyfrom the supplier.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 216 SCREW3 NAS1149CN832R 216 WASHERNOTE(S)

Refer to the AIRBUS Ref. SM if you find part numbers of hardware components whichyou cannot identify. The SM will give you the correct part number to part numberrelationship.

Components for task set A320-A-25-XX-1BPV-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment


AIRBUS Material, Logistics and SuppliersCustomer Order FulfilmentWeg beim Jaeger 15022335 HAMBURGGERMANYPhone: +49 (0) 40 5076 4002E-mail: Please contact your Single Point Of Contact(SPOC)Internet: http://spares.airbus.com

NOTE(S)Customers with aircraft shown in the applicability of this Service Bulletin should senda purchase order to AIRBUS at the address given above and quote the number of thisService Bulletin.

ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

1 606A00306-000(D4296) 54 BRACKET (1)

NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.


CONFIG 001


E. LIST OF EXISTING PARTSInterchangeable parts for task set A320-A-25-XX-1BPV-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESBRACKET 606A00305-000 606A00306-000 01 (1) (2)BRACKET 606A00305-001 606A00306-000 01 (1) (2)COMPARTMENTASSY-OVHD STWG E2529795100600 E2529795300000 01 (1) (2)

COMPARTMENTASSY-OVHD STWG E2529795100700 E2529795300100 01 (1) (2)



















COMPARTMENTASSY-OVHD STWG E2529796000500 E2529796300100 01


CONFIG 001


DESCRIPTION OLD PART No. NEW PART No. INT SEE NOTESCOMPARTMENTASSY-OVHD STWG E2529796100600 E2529796500000 01 (1) (2)









NOTE(S)For definitions of interchangeability codes in column INT. refer to ATA (CSDD Chapter2).Only the mixability configuration(s) and condition(s) stated in this Service Bulletin areapproved.

(1): An accomplishment Overhead Stowage Compartment (OHSC) per OHSC isallowed leading to a mixed configuration until the Service Bulletin is completelyaccomplished.

(2): The interchangeability possibilities are for new or modified parts introduced by theaccomplishment of this Service Bulletin.

Spare parts for task set A320-A-25-XX-1BPV-01000-93AA-A Replacement of theBin in the Pivoting Overhead Stowage Compartment

DESCRIPTION OLD PART No. SEE NOTESBRACKET 606A00305-000 (1)BRACKET 606A00305-001 (1)COMPARTMENT ASSY-OVHD STWG E2529795100600 (1)COMPARTMENT ASSY-OVHD STWG E2529795100700 (1)COMPARTMENT ASSY-OVHD STWG E2529795200000 (1)COMPARTMENT ASSY-OVHD STWG E2529795200100 (1)COMPARTMENT ASSY-OVHD STWG E2529795200200 (1)COMPARTMENT ASSY-OVHD STWG E2529795200300 (1)COMPARTMENT ASSY-OVHD STWG E2529795200400 (1)COMPARTMENT ASSY-OVHD STWG E2529795200500 (1)COMPARTMENT ASSY-OVHD STWG E2529795200600 (1)COMPARTMENT ASSY-OVHD STWG E2529795200700 (1)COMPARTMENT ASSY-OVHD STWG E2529795200800 (1)COMPARTMENT ASSY-OVHD STWG E2529795200900 (1)


CONFIG 001


DESCRIPTION OLD PART No. SEE NOTESCOMPARTMENT ASSY-OVHD STWG E2529795201100 (1)COMPARTMENT ASSY-OVHD STWG E2529795201200 (1)COMPARTMENT ASSY-OVHD STWG E2529795201800 (1)COMPARTMENT ASSY-OVHD STWG E2529795400600 (1)COMPARTMENT ASSY-OVHD STWG E2529795400700 (1)COMPARTMENT ASSY-OVHD STWG E2529795500000 (1)COMPARTMENT ASSY-OVHD STWG E2529795500600 (1)COMPARTMENT ASSY-OVHD STWG E2529795500700 (1)COMPARTMENT ASSY-OVHD STWG E2529796000500COMPARTMENT ASSY-OVHD STWG E2529796100600 (1)COMPARTMENT ASSY-OVHD STWG E2529796100700 (1)COMPARTMENT ASSY-OVHD STWG E2529796200000 (1)COMPARTMENT ASSY-OVHD STWG E2529796200100 (1)COMPARTMENT ASSY-OVHD STWG E2529796200400 (1)COMPARTMENT ASSY-OVHD STWG E2529796200500 (1)COMPARTMENT ASSY-OVHD STWG E2529797200600 (1)COMPARTMENT ASSY-OVHD STWG E2529797201000 (1)NOTE(S)(1): The parts listed here must not be installed anymore on aircraft which have

accomplished this Service Bulletin or which have the equivalent productionmodification embodied.


CONFIG 001


3. ACCOMPLISHMENT INSTRUCTIONSTask set A320-A-25-XX-1BPV-01000-93AA-AReplacement of the Bin in the Pivoting Overhead Stowage Compartment

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONSINCLUDED IN THE REFERENCED PROCEDURES.

CAUTION: ALWAYS OBEY THE PRECAUTIONS THAT FOLLOW TO KEEP ELECTRICALWIRING IN A SATISFACTORY CONDITION (ELECTRICALLY AND MECHANICALLYSERVICEABLE). WHEN YOU DO A MAINTENANCE WORK, REPAIRS ORMODIFICATIONS, ALWAYS KEEP ELECTRICAL WIRING, COMPONENTS ANDTHE WORK AREA AS CLEAN AS POSSIBLE. TO DO THIS:- PUT PROTECTION, SUCH AS PLASTIC SHEETING, CLOTHS, ETC., AS

NECESSARY ON WIRING AND COMPONENTS.- REGULARLY REMOVE ALL SHAVINGS, UNWANTED MATERIAL AND

OTHER CONTAMINATION.THESE PRECAUTIONS WILL DECREASE THE RISK OF CONTAMINATION ANDDAMAGE TO THE ELECTRICAL WIRING INSTALLATION.IF THERE IS CONTAMINATION, REFER TO Ref. ESPM 20-55-00.

NOTE: The accomplishment instructions of this Service Bulletin include procedures given inother documents or in other sections of the Service Bulletin. When the words “refer to”are used and the operator has a procedure accepted by the local authority he belongs to,the accepted alternative procedure can be used. When the words “in accordance with”are used then the given procedure must be followed.

NOTE: The access and close-up instructions, not comprising return to service tests, in thisService Bulletin do not constitute or affect the technical intent of the Service Bulletin.Operators can therefore, as deemed necessary, omit or add access and/or close-up stepsto add flexibility to their maintenance operations as long as the technical intent of theService Bulletin is met within the set parameters.

NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms. Referto paragraph 1.J., References, for the definition of acronyms.

NOTE: Discarded parts must be managed at the operator's discretion.

A. TASK SET ASSOCIATED INFORMATIONTask Manpower

TOTAL MAN-HOURS 35.50 hELAPSED TIME (HOURS) 21.00 h

B. PREPARATION(1) Task A320-A-25-XX-1BPV-01001-540A-A - Job Set-up

Job Set-Up InformationManpower/Resources/Skills

Man-hours 0.25 hMinimum Number of person 1Elapsed Time 0.25 hSkills Utility


CONFIG 001


Referenced Information

Manuals/Drawings References/Sheets

AMM Task 12-34-24-869-802Task 24-42-00-861-001

Procedure

NOTE: For the basic Aircraft configuration, refer to AMM Chapter “Introduction -Aircraft status for maintenance" in Manual Front Matter section.

(a) Make sure that the aircraft is electrically grounded, refer to Ref. AMM Task12-34-24-869-802.

(b) Energize the ground service network, refer to Ref. AMM Task 24-42-00-861-001.(c) Make sure that the bin of the Overhead Stowage Compartment (OHSC) is empty.

If necessary:- Remove, identify and retain any installed equipment.- Remove, identify and retain any attachment assemblies from the bin.

NOTE: Items will be re-installed in the new bins.

C. PROCEDURE(1) Task A320-A-25-XX-1BPV-01001-920A-A - Replace the Bin of the Pivoting

Overhead Stowage Compartment (OHSC)Job Set-Up Information

Manpower/Resources/Skills

Man-hours 29.00 hMinimum Number of person 3Elapsed Time 14.50 hSkills Cabin

Material necessary to do the job

ConsumablesITEM REFERENCE CML DESCRIPTION DRAWING SEE NOTES

08BAA9 Non Aqueous Cleaner -General

14SBA1 Textile - Lint free Cotton

Part kit 251BPVD01R03ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000000 6 CMPRTMNTE2529795000100 5 CMPRTMNTE2529795000200 7 CMPRTMNTE2529795000300 7 CMPRTMNTE2529795000400 2 CMPRTMNTE2529795000500 3 CMPRTMNTE2529795000600 1 CMPRTMNTE2529795000700 1 CMPRTMNT


CONFIG 001


Part kit 251BPVD01R03ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES

E2529795000800 2 CMPRTMNTE2529795000900 1 CMPRTMNTE2529795001000 1 CMPRTMNTE2529795001300 2 CMPRTMNTE2529795001800 1 CMPRTMNTE2529795300000 1 CMPRTMNTE2529795300100 1 CMPRTMNTE2529795600000 1 CMPRTMNTE2529795600100 1 CMPRTMNTE2529795700000 1 CMPRTMNTE2529795700200 1 CMPRTMNTE2529795700500 1 CMPRTMNTE2529796300100 1 CMPRTMNTE2529796500000 1 CMPRTMNTE2529796500100 1 CMPRTMNTE2529796600000 1 CMPRTMNTE2529796600100 1 CMPRTMNTE2529796600200 1 CMPRTMNTE2529796600300 2 CMPRTMNTE2529797000000 1 CMPRTMNTE2529797000400 1 CMPRTMNTE2529797000600 2 CMPRTMNT

Part kit 251BPVD05R01ITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES2 NAS1801-08-5 216 SCREW3 NAS1149CN832R 216 WASHER

ComponentsITEM PART No. QTY (UM) KEYWORD DRAWING SEE NOTES1 606A00306-000 54 BRACKET (1)NOTE(S)(1): The components listed above are not an AIRBUS Kit, the required parts must be

ordered as necessary through the given channel.


Manuals/Drawings References/Sheets

AMM06-20-00, Page Block 001Task 25-24-41-000-802Task 25-24-41-400-802

CML CONSUMABLE MATERIAL LIST (CML)

Procedure


CONFIG 001


(a) Standard Practices1 For the removal of the bin, refer to Ref. AMM Task 25-24-41-000-802.2 For the installation of the bin, refer to Ref. AMM Task 25-24-41-400-802.3 For the specification of Material application codes, refer to Ref. CML.4 For the identification of zones, refer to Ref. AMM 06-20-00, Page Block 001.5 For a typical installation of the bin, refer to Ref. Fig. Bin Installation - Typical6 For the replacement of the X-Fixation bracket, refer to Ref. Fig. Fixation

Bracket Replacement.(b) Replace bin assembly 1F FL EE

1 Remove:

1 COMPARTMENT ASSY-OVHD STWG

E2529795100600 Discard

2 Replace the X-fixation bracket in the housing.a Remove:

4 SCREW Item (2) Discard

4 WASHER Item (3) Discard

1 BRACKET 606A00305-000 Item (1) Discardb Clean the work area with:

Non Aqueous Cleaner -General

08BAA9

and

Textile - Lint free Cotton 14SBA1 c Install:

1 BRACKET 606A00306-000 Item 1

4 WASHER NAS1149CN832R Item 3

4 SCREW NAS1801-08-5 Item 23 Reidentify the OHSC housing.

a To find the correct PN for the placard to be installed, refer to Ref.Appendix PART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUSMaterial, Logistics and Suppliers, Customer Order Fulfilment.

b Install the OHSC housing placard, refer to Ref. Fig. Housing PlacardLocation.

4 Install:


E2529795300000

(c) Replace bin assembly 1F FR EE


CONFIG 001


1 Remove:


E2529795100700 Discard






08BAA9

and








4 Install:


E2529795300100

(d) Replace bin assembly 2F AL ST1 Remove:


E2529795200000 Discard




6 BRACKET 606A00305-000 Item (1) Discard


CONFIG 001


b Clean the work area with:


08BAA9

and








4 Install:


E2529795000000

(e) Replace bin assembly 2F AR STD1 Remove:


E2529795200100 Discard






08BAA9

and






CONFIG 001





4 Install:


E2529795000100

(f) Replace bin assembly 2F FL ST1 Remove:


E2529795200200 Discard






08BAA9

and








4 Install:


E2529795000200

(g) Replace bin assembly 2F FR STD


CONFIG 001


1 Remove:


E2529795200300 Discard






08BAA9

and








4 Install:


E2529795000300

(h) Replace bin assembly 2F AL EE1 Remove:


E2529795200400 Discard






CONFIG 001




08BAA9

and








4 Install:


E2529795000400

(i) Replace bin assembly 2F AR EE1 Remove:


E2529795200500 Discard






08BAA9

and






CONFIG 001





4 Install:


E2529795000500

(j) Replace bin assembly 2F FL EE1 Remove:


E2529795200600 Discard






08BAA9

and








4 Install:


E2529795000600

(k) Replace bin assembly 2F FR EE


CONFIG 001


1 Remove:


E2529795200700 Discard






08BAA9

and








4 Install:


E2529795000700

(l) Replace bin assembly 2F LH SYM1 Remove:


E2529795200800 Discard






CONFIG 001




08BAA9

and








4 Install:


E2529795000800

(m) Replace bin assembly 2F RH SYM1 Remove:


E2529795200900 Discard






08BAA9

and






CONFIG 001





4 Install:


E2529795000900

(n) Replace bin assembly 2F LH 3FS1 Remove:


E2529795201100 Discard






08BAA9

and








4 Install:


E2529795001000

(o) Replace bin assembly 2F AR MCU


CONFIG 001


1 Remove:


E2529795201200 Discard






08BAA9

and








4 Install:


E2529795001300

(p) Replace bin assembly 2F AL LOCK1 Remove:


E2529795201800 Discard






CONFIG 001




08BAA9

and








4 Install:


E2529795001800

(q) Replace bin assembly 2FP FL EE1 Remove:


E2529795400600 Discard






08BAA9

and






CONFIG 001





4 Install:


E2529795600000

(r) Replace bin assembly 2FP FR EE1 Remove:


E2529795400700 Discard






08BAA9

and








4 Install:


E2529795600100

(s) Replace bin assembly US1 AL STD


CONFIG 001


1 Remove:


E2529795500000 Discard






08BAA9

and








4 Install:


E2529795700000

(t) Replace bin assembly US3 FL EE1 Remove:


E2529795500600 Discard






CONFIG 001




08BAA9

and








4 Install:


E2529795700200

(u) Replace bin assembly US4 FR EE1 Remove:


E2529795500700 Discard






08BAA9

and






CONFIG 001





4 Install:


E2529795700500

(v) Replace bin assembly 1FPC RH EE1 Remove:


E2529796000500 Discard






08BAA9

and








4 Install:


E2529796300100

(w) Replace bin assembly 1FC LH


CONFIG 001


1 Remove:


E2529796100600 Discard






08BAA9

and








4 Install:


E2529796500000

(x) Replace bin assembly 1FC EE RH1 Remove:


E2529796100700 Discard






CONFIG 001




08BAA9

and








4 Install:


E2529796500100

(y) Replace bin assembly 2FC LH STD1 Remove:


E2529796200000 Discard






08BAA9

and






CONFIG 001





4 Install:


E2529796600000

(z) Replace bin assembly 2FC RH STD1 Remove:


E2529796200100 Discard






08BAA9

and








4 Install:


E2529796600100

(aa) Replace bin assembly 2FC LH EE


CONFIG 001


1 Remove:


E2529796200400 Discard






08BAA9

and








4 Install:


E2529796600200

(ab) Replace bin assembly 2FC RH EE1 Remove:


E2529796200500 Discard






CONFIG 001




08BAA9

and








4 Install:


E2529796600300

(ac) Replace bin assembly 2FR LH EE1 Remove:


E2529797200600 Discard

2 Reidentify the OHSC housing.a To find the correct PN for the placard to be installed, refer to Ref.

Appendix PART NUMBER ROLL INFORMATION.



3 Install:


E2529797000000

(ad) Replace bin assembly 2FRS EE1 Remove:


E2529797201000 Discard

2 Reidentify the OHSC housing.


CONFIG 001





3 Install:


E2529797000400

(ae) Replace bin assembly 2FR EE STIFF1 Remove:


E2529797200600 Discard

2 Reidentify the OHSC housing.a To find the correct PN for the placard to be installed, refer to Ref.

Appendix PART NUMBER ROLL INFORMATION.



3 Install:


E2529797000600


CONFIG 001

Figure ICN-A320-A-25XX1BPV-A-FAPE3-00YY4-A-001-01 SHEET 1/1REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19

Bin Installation - TypicalPage 41

CONF 001

Z200

A

TYPICAL

TYPICAL

A

B

B

ICN-A320-A-25XX1BPV-A-FAPE3-00YY4-A-001-01


CONFIG 001

Figure ICN-A320-A-25XX1BPV-A-FAPE3-01AOL-A-001-01 SHEET 1/2REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19

Fixation Bracket ReplacementPage 42

CONF 001

Z200

A

TYPICAL

A

B

C D

C D

B

VIEW SHOWN WITHOUT BINSTYPICAL

ICN-A320-A-25XX1BPV-A-FAPE3-01AOL-A-001-01


CONFIG 001

Figure ICN-A320-A-25XX1BPV-A-FAPE3-01AOV-A-002-01 SHEET 2/2REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19

Fixation Bracket ReplacementPage 43

CONF 001

(1)

(3)(2)

1

32

BEFORE

AFTER

C

D

TYPICAL

TYPICAL

ICN-A320-A-25XX1BPV-A-FAPE3-01AOV-A-002-01


CONFIG 001

Figure ICN-A320-A-25XX1BPV-A-FAPE3-01HXF-A-001-01 SHEET 1/1REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19

Housing Placard LocationPage 44

CONF 001

Z200

A

TYPICAL

A

B

B

VIEW SHOWN WITHOUT BINSTYPICAL

SB25-1BPV IMPLEMENTED

NEW P/N: E25297XXXXXXXX02 03

NOTE:MAKE EXISTING P/N UNREADABLE01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

01

ICN-A320-A-25XX1BPV-A-FAPE3-01HXF-A-001-01


CONFIG 001


(2) Task A320-A-25-XX-1BPV-01001-900A-A - Reidentify the Overhead StowageCompartment AssembliesJob Set-Up Information



Procedure(a) Reidentify the OHSC assembly.

1 To find the correct PN for the placard to be installed, refer to Ref. AppendixPART NUMBER ROLL INFORMATION.

NOTE: Placards shall be ordered as necessary through AIRBUS Material,Logistics and Suppliers, Customer Order Fulfilment.

2 Install the OHSC assembly placard, refer to Ref. Fig. OHSC AssemblyPlacard Location.


CONFIG 001

Figure ICN-A320-A-25XX1BPV-A-FAPE3-01DPM-A-001-01 SHEET 1/1REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19

OHSC Assembly Placard LocationPage 46

CONF 001

Z200

A

TYPICAL

TYPICAL

A

B

B

SB25-1BPV IMPLEMENTED

NEW P/N: E25294XXXXXXXX

NOTE:MAKE EXISTING P/N UNREADABLE01

01

BOND SB-PLACARD NEAR TO EXISTING IDENTIFICATION PLACARD02

REFER TO TABLE ON APPENDIX FOR AFFECTED PART NUMBER03

02 03

C

C

ICN-A320-A-25XX1BPV-A-FAPE3-01DPM-A-001-01


CONFIG 001


D. PREPARATION FOR TESTNone

E. TEST(1) Task A320-A-25-XX-1BPV-01001-320A-A - Operational Test

Job Set-Up InformationManpower/Resources/Skills



Manuals/Drawings References/SheetsAMM Task 25-24-00-710-002

Procedure(a) Open and close the bin to check the correct operation.(b) If necessary do the adjustment of the bin, refer to Ref. AMM Task

25-24-00-710-002.F. CLOSE-UP

(1) Task A320-A-25-XX-1BPV-01001-740A-A - Close-upJob Set-Up Information


Man-hours 0.25 hMinimum Number of person 1Elapsed Time 0.25 hSkills Utility

Procedure(a) Make sure that the OHSC bins are clean and clear of tools and other items of

equipment.1 Open the OHSC bin.2 Install, where necessary, the identified removed equipment in the OHSC

bin.3 Close the OHSC bin.

(b) Put the aircraft back to its initial configuration.G. ADMINISTRATIVE

(1) Task A320-A-25-XX-1BPV-01001-90AA-A - Administrative

ProcedureConfirm in the applicable aircraft records that you have completed all the work definedin this Service Bulletin task set as required.


CONFIG 001 APPENDIX


APPENDIXA. PART NUMBER ROLL INFORMATION

PART NUMBER ROLL INFORMATIONThis Appendix gives information about the Part Number roll after accomplishment of thisService Bulletin.


CONFIG 001 APPENDIX

Figure ICN-A320-A-25XX1BPV-A-FAPE3-01DPJ-A-002-01 SHEET 1/3REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19

Part Number Roll InformationPage 49

CONF 001

PART NUMBER ROLL

TOP OHSC 4F E252-94000-000-00 E252-94000-006-00D252-93571-000-00

E252-94000-002-00 E252-94000-008-00D252-93571-002-00

E252-94001-000-00 E252-94001-006-00D252-93571-006-00

E252-94001-002-00 E252-94001-012-00D252-93571-008-00

E252-94002-002-00 E252-94002-024-00D252-93571-020-00

E252-94002-004-00 E252-94002-026-00D252-93571-022-00

TOP OHSC 4F TS E252-94003-002-00 E252-94003-020-00D252-93571-036-00

TOP OHSC 4F TS E252-94003-004-00 E252-94003-022-00D252-93571-038-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

E252-94014-002-00 E252-94014-020-00

E252-94014-004-00 E252-94014-032-00

E252-94015-002-00 E252-94015-020-00

E252-94015-004-00 E252-94015-022-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F TS

TOP OHSC 4F TS

E252-94016-002-00 E252-94016-010-00

E252-94016-004-00 E252-94016-012-00

E252-94017-002-00 E252-94017-018-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

D252-93571-102-00

D252-93571-104-00

D252-93571-118-00

D252-93571-120-00

D252-93571-132-00

D252-93571-134-00

D252-93571-138-00

E252-94017-004-00 E252-94017-020-00

E252-94018-000-00 E252-94018-012-00

E252-94018-002-00 E252-94018-018-00

E252-94018-004-00 E252-94018-020-00

E252-94019-000-00 E252-94019-010-00

E252-94019-002-00 E252-94019-012-00

E252-94020-002-00 E252-94020-018-00

E252-94020-004-00 E252-94020-020-00

E252-94021-002-00 E252-94021-018-00

E252-94021-004-00 E252-94021-020-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

E252-94022-002-00 E252-94022-020-00

E252-94022-004-00 E252-94022-022-00

E252-94022-006-00 E252-94022-024-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

D252-93571-140-00

D252-93571-150-00

D252-93571-152-00

D252-93571-154-00

D252-93571-162-00

D252-93571-164-00

D252-93571-174-00

D252-93571-176-00

D252-93571-188-00

D252-93571-190-00

D252-93572-002-00

D252-93572-004-00

D252-93572-006-00

E252-94023-002-00 E252-94023-020-00

E252-94023-004-00 E252-94023-022-00

E252-94023-006-00 E252-94023-024-00

E252-94024-000-00 E252-94024-008-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

D252-93572-018-00

D252-93572-020-00

D252-93572-022-00

D252-93572-032-00

TOP OHSC

D252-93646-000-00

D252-93646-002-00

D252-93646-006-00

D252-93646-008-00

D252-93646-020-00

D252-93646-022-00

D252-93646-034-00

D252-93646-036-00

D252-93646-094-00

D252-93646-096-00

D252-93646-110-00

D252-93646-112-00

D252-93646-124-00

D252-93646-126-00

D252-93646-130-00

D252-93646-132-00

D252-93646-142-00

D252-93646-144-00

D252-93646-146-00

D252-93646-152-00

D252-93646-154-00

D252-93646-160-00

D252-93646-162-00

D252-93646-170-00

D252-93646-172-00

D252-93646-180-00

D252-93646-182-00

D252-93646-184-00

D252-93646-192-00

D252-93646-194-00

D252-93646-196-00

D252-93647-004-00

OHSC NAMEAFTER SB25-1BPW

PRE PN TOP OHSCBEFORE SB25-1BPW

E252-97904-018-00

E252-97905-000-00

E252-97914-000-00

E252-97915-000-00

E252-97904-000-00

E252-97904-000-00

E252-97914-015-00

E252-97914-015-00

E252-97904-021-00

E252-97904-021-00

E252-97914-026-00

E252-97914-026-00

E252-97904-024-00

E252-97904-024-00

E252-97914-024-00

E252-97914-024-00

E252-97904-008-00

E252-97904-008-00

E252-97904-008-00

E252-97914-027-00

E252-97914-027-00

E252-97904-031-00

E252-97904-016-00

E252-97914-008-00

E252-97914-008-00

E252-97904-010-00

E252-97904-037-00

E252-97904-037-00

E252-97914-010-00

E252-97914-037-00

E252-97914-037-00

E252-97906-000-00

PRE PNHOUSING

E252-97924-010-00

E252-97925-000-00

E252-97934-000-00

E252-97935-000-00

E252-97924-000-00

E252-97924-000-00

E252-97934-012-00

E252-97934-012-00

E252-97924-012-00

E252-97924-012-00

E252-97934-017-00

E252-97934-017-00

E252-97924-013-00

E252-97924-013-00

E252-97934-015-00

E252-97934-015-00

E252-97924-006-00

E252-97924-006-00

E252-97924-006-00

E252-97934-018-00

E252-97934-018-00

E252-97924-016-00

E252-97924-008-00

E252-97934-008-00

E252-97934-008-00

E252-97924-007-00

E252-97924-017-00

E252-97924-017-00

E252-97934-009-00

E252-97934-022-00

E252-97934-022-00

E252-97926-000-00

POST PNHOUSING

PRE PN TOP OHSC PLACARD PNTOP OHSCPOST PN

HOUSING

D252-93648-044-00

PLACARD PN

D252-93648-060-00

D252-93648-108-00

D252-93648-146-00

D252-93648-024-00

D252-93648-024-00

D252-93648-130-00

D252-93648-130-00

D252-93648-048-00

D252-93648-048-00

D252-93648-136-00

D252-93648-136-00

D252-93648-050-00

D252-93648-050-00

D252-93648-132-00

D252-93648-132-00

D252-93648-036-00

D252-93648-036-00

D252-93648-036-00

D252-93648-138-00

D252-93648-138-00

D252-93648-056-00

D252-93648-040-00

D252-93648-122-00

D252-93648-122-00

D252-93648-038-00

D252-93648-058-00

D252-93648-058-00

D252-93648-124-00

D252-93648-144-00

D252-93648-144-00

D252-93648-064-00

ICN-A320-A-25XX1BPV-A-FAPE3-01DPJ-A-002-01


CONFIG 001 APPENDIX

Figure ICN-A320-A-25XX1BPV-A-FAPE3-01DPK-A-002-01 SHEET 2/3REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19


CONF 001

E252-94024-002-00 E252-94024-010-00

E252-94025-000-00 E252-94025-008-00

E252-94025-002-00 E252-94025-010-00

E252-94026-004-00 E252-94026-020-00

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

TOP OHSC 4F

E252-94027-002-00 E252-94027-018-00TOP OHSC 4F

E252-94027-004-00 E252-94027-020-00TOP OHSC 4F

E252-94028-002-00 E252-94028-022-00TOP OHSC 4F

E252-94028-004-00 E252-94028-024-00TOP OHSC 4F

E252-94029-002-00 E252-94029-020-00TOP OHSC 4F

E252-94029-004-00 E252-94029-022-00TOP OHSC 4F

D252-93572-034-00

D252-93572-040-00

D252-93572-042-00

D252-93572-050-00

D252-93572-062-00

D252-93572-064-00

D252-93572-076-00

D252-93572-078-00

D252-93572-090-00

D252-93572-092-00

E252-94048-002-00 E252-94048-020-00TOP OHSC 3FC

E252-94048-004-00 E252-94048-022-00

E252-94048-006-00 E252-94048-024-00

E252-94049-002-00 E252-94049-016-00

E252-94049-004-00 E252-94049-018-00

E252-94052-002-00 E252-94052-010-00

E252-94052-004-00 E252-94052-012-00

E252-94053-002-00 E252-94053-012-00

E252-94053-004-00 E252-94053-014-00

TOP OHSC 2FR E252-94054-000-00 E252-94054-004-00

TOP OHSC 2FR E252-94054-002-00 E252-94054-006-00

TOP OHSC 2FR E252-94055-000-00 E252-94055-006-00

TOP OHSC 2FR E252-94055-002-00 E252-94055-008-00

TOP OHSC 2FC UP AIR

TOP OHSC 2FC UP AIR

TOP OHSC 2FC UP AIR

TOP OHSC 2FC UP AIR

TOP OHSC 3FC

TOP OHSC 3FC

TOP OHSC 3FC

TOP OHSC 3FC

D252-93572-136-00

D252-93572-138-00

D252-93572-140-00

D252-93572-150-00

D252-93572-152-00

D252-93572-162-00

D252-93572-164-00

D252-93572-170-00

D252-93572-172-00

D252-93572-176-00

D252-93572-178-00

D252-93572-182-00

D252-93572-184-00

E252-94056-000-00 E252-94056-004-00TOP OHSC 2FC

E252-94056-002-00 E252-94056-006-00TOP OHSC 2FC

E252-94057-000-00 E252-94057-004-00TOP OHSC 2FC

E252-94057-002-00 E252-94057-006-00TOP OHSC 2FC

E252-94058-002-00 E252-94058-010-00TOP OHSC 2F

E252-94058-004-00 E252-94058-012-00TOP OHSC 2F

E252-94059-002-00 E252-94059-010-00TOP OHSC 2F

E252-94059-004-00 E252-94059-012-00TOP OHSC 2F

E252-94060-000-00 E252-94060-008-00TOP OHSC 2FC

D252-93572-188-00

D252-93572-190-00

D252-93572-192-00

D252-93572-194-00

D252-93572-198-00

D252-93573-000-00

D252-93573-006-00

D252-93573-008-00

D252-93573-012-00

D252-93647-006-00

D252-93647-010-00

D252-93647-012-00

D252-93647-016-00

D252-93647-024-00

D252-93647-026-00

D252-93647-034-00

D252-93647-036-00

D252-93647-044-00

D252-93647-046-00

D252-93647-076-00

D252-93647-078-00

D252-93647-080-00

D252-93647-090-00

D252-93647-092-00

D252-93647-100-00

D252-93647-102-00

D252-93647-106-00

D252-93647-108-00

D252-93647-112-00

D252-93647-114-00

D252-93647-116-00

D252-93647-118-00

D252-93647-122-00

D252-93647-124-00

D252-93647-126-00

D252-93647-128-00

D252-93647-130-00

D252-93647-132-00

D252-93647-136-00

D252-93647-138-00

D252-93647-142-00

PART NUMBER ROLL

E252-97906-000-00

E252-97916-000-00

E252-97916-000-00

E252-97904-017-00

E252-97914-014-00

E252-97914-014-00

E252-97904-020-00

E252-97904-020-00

E252-97914-002-00

E252-97914-002-00

E252-97903-000-00

E252-97903-034-00

E252-97903-035-00

E252-97913-003-00

E252-97913-034-00

E252-97907-004-00

E252-97907-004-00

E252-97917-004-00

E252-97917-004-00

E252-97908-000-00

E252-97908-000-00

E252-97918-000-00

E252-97918-000-00

E252-97907-000-00

E252-97907-000-00

E252-97917-000-00

E252-97917-000-00

E252-97902-000-00

E252-97902-000-00

E252-97912-000-00

E252-97912-000-00

E252-97907-005-00

E252-97926-000-00

E252-97936-000-00

E252-97936-000-00

E252-97924-009-00

E252-97934-011-00

E252-97934-011-00

E252-97924-011-00

E252-97924-011-00

E252-97934-002-00

E252-97934-002-00

E252-97923-000-00

E252-97923-004-00

E252-97923-005-00

E252-97933-001-00

E252-97933-003-00

E252-97927-001-00

E252-97927-001-00

E252-97937-001-00

E252-97937-001-00

E252-97928-000-00

E252-97928-000-00

E252-97938-000-00

E252-97938-000-00

E252-97927-000-00

E252-97927-000-00

E252-97937-000-00

E252-97937-000-00

E252-97920-000-00

E252-97920-000-00

E252-97930-000-00

E252-97930-000-00

E252-97927-002-00

TOP OHSCOHSC NAME

AFTER SB25-1BPWPRE PN TOP OHSC

BEFORE SB25-1BPWPRE PN

HOUSINGPOST PN

HOUSINGPRE PN TOP OHSC PLACARD PN

TOP OHSCPOST PN

HOUSINGPLACARD PN

D252-93648-064-00

D252-93648-152-00

D252-93648-152-00

D252-93648-042-00

D252-93648-128-00

D252-93648-128-00

D252-93648-046-00

D252-93648-046-00

D252-93648-112-00

D252-93648-112-00

D252-93648-012-00

D252-93648-020-00

D252-93648-022-00

D252-93648-102-00

D252-93648-106-00

D252-93648-070-00

D252-93648-070-00

D252-93648-158-00

D252-93648-158-00

D252-93648-076-00

D252-93648-076-00

D252-93648-164-00

D252-93648-164-00

D252-93648-068-00

D252-93648-068-00

D252-93648-156-00

D252-93648-156-00

D252-93648-004-00

D252-93648-004-00

D252-93648-094-00

D252-93648-094-00

D252-93648-072-00

ICN-A320-A-25XX1BPV-A-FAPE3-01DPK-A-002-01


CONFIG 001 APPENDIX

Figure ICN-A320-A-25XX1BPV-A-FAPE3-01DPL-A-003-01 SHEET 3/3REV 00 May 27/19 A320-25-1BPVREV 01 Jun 27/19


CONF 001

E252-94061-000-00 E252-94061-010-00TOP OHSC 2FC

E252-94061-002-00 E252-94061-014-00TOP OHSC 2FC

E252-94062-000-00 E252-94062-012-00TOP OHSC 2FR

E252-94062-002-00 E252-94062-016-00

E252-94063-000-00 E252-94063-014-00

E252-94063-002-00 E252-94063-016-00

TOP OHSC 1FC E252-94068-000-00 E252-94068-008-00

TOP OHSC 2FR

TOP OHSC 2FR

TOP OHSC 2FR

E252-94068-002-00 E252-94068-010-00TOP OHSC 1FC

E252-94069-000-00 E252-94069-008-00TOP OHSC 1FC

E252-94069-002-00 E252-94069-010-00TOP OHSC 1FC

D252-93573-018-00

D252-93573-020-00

D252-93573-026-00

D252-93573-028-00

D252-93573-036-00

D252-93573-038-00

D252-93573-050-00

D252-93573-052-00

D252-93573-058-00

D252-93573-060-00

E252-94071-002-00 E252-94071-008-00TOP OHSC 3FM D252-93573-066-00

E252-94074-002-00 E252-94074-006-00TOP OHSC 2F

E252-94076-002-00 E252-94076-006-00TOP OHSC 3FM

D252-93573-072-00

D252-93573-078-00

D252-93647-146-00

D252-93647-148-00

D252-93647-152-00

D252-93647-154-00

D252-93647-160-00

D252-93647-162-00

D252-93647-170-00

D252-93647-172-00

D252-93647-176-00

D252-93647-178-00

D252-93577-006-00

D252-93647-184-00

D252-93647-188-00

PART NUMBER ROLL

E252-97917-005-00

E252-97917-005-00

E252-97908-023-00

E252-97908-003-00

E252-97918-008-00

E252-97018-008-00

E252-97900-012-00

E252-97900-012-00

E252-97910-013-00

E252-97910-013-00

E252-97910-001-00

E252-97902-006-00

E252-97905-011-00

E252-97937-002-00

E252-97937-002-00

E252-97928-002-00

E252-97928-001-00

E252-97938-003-00

E252-97938-003-00

E252-97901-001-00

E252-97901-001-00

E252-97911-003-00

E252-97911-003-00

E252-97911-001-00

E252-97920-002-00

E252-97925-001-00

TOP OHSCOHSC NAME

AFTER SB25-1BPWPRE PN TOP OHSC

BEFORE SB25-1BPWPRE PN

HOUSINGPOST PN

HOUSINGPRE PN TOP OHSC PLACARD PN

TOP OHSCPOST PN

HOUSINGPLACARD PN

D252-93648-160-00

D252-93648-160-00

D252-93648-080-00

D252-93648-078-00

D252-93648-170-00

D252-93648-170-00

D252-93648-002-00

D252-93648-002-00

D252-93648-092-00

D252-93648-092-00

D252-93648-088-00

D252-93648-008-00

D252-93648-062-00

ICN-A320-A-25XX1BPV-A-FAPE3-01DPL-A-003-01


CONFIG 001 APPENDIX


B. REPORTING SHEET


MODIFICATION No.: 162563K30846

(1) SB Reporting statusThis Service Bulletin will only be incorporated into affected customized Maintenanceand Flight Operations Products if it is duly reported to Airbus.

(2) GENERAL informationThe SB Reporting policy is published in ISI 00.00.00135. This document providesinformation regarding: the SB Reporting means and benefits, the update ofcustomized Maintenance Products and customized Flight Operations Products.If this Service Bulletin has an operational impact, refer to paragraph "Flight OperationsProducts" for further information on the update of affected Flight Operations Products.

(3) SB Reporting procedureStandard practice to report SB is to use the online reporting application onAirbusWorld.Refer to ISI 00.00.00179:

- For complete information on reporting means to Airbus, Question 2 "What arethe standard practices for SB Reporting?"

- If this SB requires previous or simultaneous accomplishment of other SBs,Question 3 "What about the reporting of prerequisite Service Bulletins?"

NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting.It is revised on a regular basis.


CONFIG 001 APPENDIX


C. QUALITY PERCEPTION FORMUse this form to tell us what is your perception of the quality of this Service Bulletin.The reported data that you provide us will be used to analyse areas of difficulties and totake corrective action to further improve the quality of our Service Bulletin.We thank you for the time you have taken in completing this form.

Quality rating of this SB 4 3 2 1Quality rating of the Accomplishment Instructions 4 3 2 1Quality rating of the Illustrations 4 3 2 1Is this SB easy to understand ? Y / N

NOTE: Please rate on a scale of 1 to 4, with 4 being the highest score

If you have difficulties in the accomplishment of this SB please quote below the area(s) andgive a short description of the issue.

Planning Material InstructionsX Applicability X Tooling X PreparationX Reason X List of Materials

Operator SuppliedX Mod/Inspection

X Manpower X Kit content X TestX References X Re-identification X Close-upX Publication X IllustrationsX Industry Support

Comments :

Operator : Date :Name/TitlePlease return this form to :AIRBUS2, ROND POINT EMILE DEWOITINE31700 BLAGNACFRANCEOr via your Resident Customer Support Office.

Documents

A318/A319/A320/A321 31700 BLAGNAC