ABB-Welcome IP · Plan x to input project structure picture. 1. 2. ... Slide 29. 1. IP Camera monitor via management software. ... input programming password

ABB-Welcome IP

01 KNX

02 IP camera

03 Alarm

04 Lift control

05 Card reader

06 Property management

August 23, 2017 Slide 2

Agenda

01 KNX


01 KNXCommissioning

1. Select KNX as a smart home control frame

3. Set IP address for KNX/NET IP interface

2. Import floor plan

4. Add device on floor plan

5. Edit device property. 6. Edit scene property

August 23, 2017 Remark: Pls refer to online manual.Slide 5

01 KNX1. Select KNX as a smart home control frame

1. Press “Arm for away” and input password* to enter the engineering mode.

2. Choose ‘function’ page, focus on “Smart Home” item, and choose “i-bus@KNX”.

1

2


01 KNX2. Import floor plan


2. Choose ‘Picture’ page and choose Floor Plan x to input project structure picture.

1

2

Remark: Pls refer to online manual.


01 KNX


1. Press to enter smart home functionality.

2. Press “Setting” and input password* to enter the setting.

3. Choose KNX INTERFACE, then Choose “IP type”

1) If the IPS and the IS are in the same network, choose “IS Network“, and the “IP Address” input the IS address.

2) If the IPS and the IS are not in the same network, choose “Not IS Network“, and the “IP Address” input the IS address, and give “local IP Address” a virtual network segment address.

Without IP Gateway

1

2

3

4



01 KNX

August 23, 2017 Remark: if IS is under Slide 8

1. Login in IP Gateway.

2. Select “KNX setting”.

3. Input IP address.

With IP Gateway

4. Add device on floor plan

01 KNX


1. Choose ‘Position’

2. Add devices on floor plan

1

2

5. Edit device property

01 KNX


1. Choose ‘Attribute’

2. Choose the device in the floor plan, which needs to be set parameters.

3. Choose device type

4. Set the parameter.

5. Set “Alarm Linkage”.

1

2

3

4

5

6. Edit scene property

01 KNX


1. Select ‘Scene’.

2. Choose one of the icon.

3. Set its parameter.

1

2

3


01 KNXSwitching

Single device control

Scene control

Timer setting

1. Single Device control

01 KNX


1. Press to enter smart home functionality.

2. Press one of the icon to activate or deactivate the device.

1

2

2. Scene control

01 KNX


1. Press ‘Scene’

2. Press the Scene icon.

1

2

3. Time control

01 KNX


1. Press ‘Timer’ to set activate during time.

2. Choose “Single device”.

3. Choose the device which needs to set time.

4. Set two periods of time, and activate them.

1. Single device time control 1

2

3

4

3. Time control

01 KNX


1. Press ‘Timer’ to set activate during time.

2. Choose “Scene Timer”.

3. Choose the Scene which needs to set time.

4. Set period of time, and activate it.

2. Scene time control 1

2

3

4

02 IP camera / monitor


02 Private IP CameraCommissioning

1. Search IP Camera via indoor station

2. Authenticate to access IP Camera via indoor station

3. Set visible IP Camera list

1

2

Commissioning

02 Private IP Camera


Pre-conditions:

IP camera and indoor station or management software should be in the same network segment.

Initiate surveillance

Press and choose one type of monitor (take Home Monitor ad an example)

1. Search IP camera

3

45

Commissioning



2. Authenticate to access IP Camera

1

2

3Input user name and password of the camera to authorize indoor station to surveil the camera.

4

Commissioning



3. Set visible IP Camera list1

2

Select the IP camera which wants to use. Put them in to the IP-camera list.


02 Public IP CameraCommissioning

1. Search IP Camera via management software

3. Download list

2. Authenticate to access IP Camera via management software

4. Set visible IP Camera list

Commissioning

02 Public IP camera


1. Select “Surveillance device”

2. Press “Refresh” button to fresh the camera list.

1. Search IP camera

Commissioning

02 Public IP Camera


2. Authenticate to access IP Camera

1. Press “authentication” button.

Commissioning

02 Public IP Camera


3. Download list

If there are authorized cameras added on PC management software. The resident can download the camera list to their own indoor station.

Commissioning

02 Public IP Camera


4. Set visible IP Camera list 1

2

Select the IP camera which wants to use. Put them in to the IP-camera list.


02 IP camera / monitorApplication

IP Camera monitor

Picture capture

Application



1. IP Camera monitor via indoor station

Choose one camera you want to monitor from “IP-camera list”

1

2

Application



1. IP Camera monitor via management software

Choose one camera you want to monitor from “IP-camera list”

Application



2. Picture capture

During the surveillance, click " " to take a snapshot by manual.

03 Alarm


03 Alarm / Floor planCommissioning

1. Select Alarm control frame mode

3. Add alarm zone


4. Edit alarm zone property.

5. Set system parameter

Commissioning

03 Alarm / Floor plan


1. Select alarm control frame mode


2. Choose ‘Function’ page and choose to choose the “Floor Plan” mode or “Simple Mode”.

1

2


Commissioning




1. Press “setting button " on indoor station.

2. Click "Advanced setting" then input programming password and click "OK".

3. Choose “Picture” from the top bar.

4. Click “floor plan 1”, and choose one photo from SD card.

5. Click active.

1

2

3


Commissioning



3. Add alarm zone

1. Press “setting button " on indoor station.

2. Click "Advanced setting" then input 6-digit password to enter the Alarm system and click "OK".

3. Click “Alarm zone position” and then click “select”. Click on the floor plan picture to build a zone, there will be an icon for each zone, gray icon means unset. Click “save” to save.

1

2

3

Commissioning



4. Edit alarm zone property

1. Click “Alarm zone attribute” and “select”.

2. And then you can choose “zone”, “doormagnetic”, “instant”.

3. Click “zone details” to choose “location”, “mornitoringgroup”, “linked with zone”, and then click “OK” to save.

4. After editing alarm zone property, the icon will turn to green.

1

2

3

4

Commissioning



5. Set system parameter

1. Click “Alarm system timer” --“Select” to entering setting.

2. Choose a “time template” and click “Edit Timer”

3. Choose “Days”, “Start time”, “end time”, “function” and then click “OK”.4. Stick time template finishing setting, and then click “OK” to active.

1

2

3

4


03 Alarm/ Simple modeCommissioning

1. Select Alarm control frame mode

2. Add alarm zone


Commissioning

03 Alarm/ Simple mode


1. Select alarm control frame mode


2. Choose ‘Function’ page and choose to choose “Simple Mode”.

1

2

Commissioning



2. Add alarm zone

1. Press “setting button" on indoor station.

2. Click "Advanced setting" then input 6-digit password* to enter the Alarm system and click "OK“.

3. Set On/Off to enable/disable different alarm zone.

1

2


Commissioning




1. Select “Alarm Zone Setup”

2. Choose Sensor, Type, and which alarm zone.

1

2


03 AlarmApplication

Arming

Disarming

Check alarm history

Timer setting

Password management

Alarm report

Application

03 Alarm


1. Arming

2. Press to enter alarm system.

① Press “Arm all” and input password* to enable arming.

② Press “Arm for night” and input password* to enable arm for night.

③ Press “Arm for stay” and input password* to enable arm for stay.

④ Press “Arm for away” and input password* to enable arm for away.

1

2


Application

03 Alarm


2. Disarming

1. Press “Disarming” and input password* to disable arming.


Application

03 Alarm


3. Check alarm history

1. At alarm system surface, you can click “Alarm history”

2. Also, you can check alarm history via menu bar.

3. And press message icon.

1

2

3

Application

03 Alarm


4. Timer setting

1. Click “Alarm system timer” --“Select” to entering setting.

2. Choose a “time template” and click “Edit Timer”

3. Choose “Days”, “Start time”, “end time”, “function” and then click “OK”.4. Stick time template finishing setting, and then click “OK” to active.

1

2

34

Application

03 Alarm


5. Password management

Press , select “Alarm System”, and click “Adjust”.

Input programming password* and click “OK”.

You can adjust Exit delays, Entry delays and Alarm duration.

Change private password*.

Change programming password*. Change duress password*.

Click “OK” to save your re-setting.

1

2

3


Application

03 Alarm


6. Alarm report

1. When there is a Alarm occurred, management software will show out which place has a alarm and alarm detailed information.

04 Lift control


04 Lift controlCommissioning

1. Activate lift control function.

3. Set Lift controller module parameter.

2. Set lift related device(OS, CR) parameter.

4. Set Lift relay module parameter.


04 Lift control1. Activate lift control function

1. On standby mode, press[#*] + system code + [#] to enter system setting.

2. Select “System setting”.

3. Select “Lift setting”.

4. Select “Enable”.

5. Select “On” option.

1. Building Outdoor station

Remark: Once lift control function has been activated , when registering card, other than inputting card number, it should also input floor number.

1

2

3

4

August 23, 2017

Remark: Once lift control function has been activated , when registering card, other than inputting card number, it should also input floor number. And Press “LIFT + 0 + ENTER” to disable lift function.

Slide 52

04 Lift control1. Activate lift control function

1. Using Remote, press “FN + password* + ENTER” to enter setting mode.

2. Press “LIFT + 1 + ENTER” to enable lift control function.

2. Standalone card reader

August 23, 2017 Remark: In setting mode, press “#” to confirm and “*” to cancelSlide 53

04 Lift control2. Set lift related device(OS, CR) parameter

1. On standby mode, press[#*] + system code + [#] to enter system setting.

2. Select “System setting”.


4. Select “Floor No.”.

5. Input Floor No. and confirm.

1. Building outdoor station1

2

3

4

August 23, 2017 Remark: floor number: range is from -7 - -1, 1 – 64, if floor number is minus, it should press “FN + floor number” to set.Slide 54

04 Lift control2. Set lift related device(OS, CR) parameter

1. Using Remote, press “FN + Password* + ENTER” to enter setting mode.

2. Press “FLOOR + floor number* + ENTER”.

2. Standalone card reader


04 Lift control3. Set Lift controller module parameter.

1. Connect building outdoor station directly to lift control module

2. On outdoor station standby mode, press[#*] + system code + [#] to enter “System setting”.


4. Select “Block No.”

5. Input “Block No.”

1

2

3

4


04 Lift control


1. Power indicator

Flash during standby

On for programming

2. Setting indicator

T1 setting, blinks once

T2 setting, blinks twice

T3 setting, blinks thrice

T4 setting, blinks quartic

3. Local power supply4. RS485 bus to lift control module5. 16x Relay output6. SW3 to set delay time and address7. SW1/SW2 to set delay time

Relay module

67


04 Lift control

August 23, 2017

Remark: T1 – delay time for activating departure floor relayT2 – action time for activating departure floor relayT3 – delay time for activating arrival floor relay.T4 – action time for activating arrival floor relay.

Slide 57

1. Press and hold SW1 until LED change to permanent on from flashing.

2. Adjust SW3 for T1 setting and press SW2, then setting LED flash one time.

3. Adjust SW3 for T2 setting and press SW2, then setting LED flash two times.

4. Adjust SW3 for T3 setting and press SW2, then setting LED flash three times.

5. Adjust SW3 for T4 setting and press SW2, then setting LED flash four times.

6. Adjust SW3 BIT1 to off and press SW2, then then setting LED flash five times.

7. Press and hold SW1 until LED change to flashing from permanent on.

Timing setting and mode selection

Time setting value:(Plus all the on bits value together)

Bit1: 1Bit2: 2Bit3: 4Bit4: 8Bit5: 16Bit6: 32Bit7: 64Bit8: 128


04 Lift control


1. Set Module identifier of relay module(1-4 bit).

2. Set floor number(5-7 bit).

3. Set start floor number polarity(8 bit).

Set module number and start floor

1234: Module identifier (0000~1111)1 is the low bit

567: Start floor number (000~111)5 is the low bit

8: Start floor number polarity (0/1)0: basement1: Above floor


04 Lift controlapplication

Unlock to activate lift control system during communication

Unlock to activate lift control system by swiping card

Unlock to activate lift control system by password

Authorization by indoor stations intercom


04 Lift control1. Unlock to activate lift control system during communication

1. Press calling code to reach any indoor station number.

2. Indoor station unlock the door.

3. Lift will go down to outdoor station floor.

4. And visitor can only press indoor station lift floor key.

1. Building outdoor station


04 Lift control2. Unlock to activate lift control system by swiping card

1. When swiping the card in outdoor station/card reader.

2. Lift will go down to outdoor station/card reader’s floor.

3. Visitor can only press lift floor key which related to this card.

Building outdoor station/card reader


04 Lift control3. Unlock to activate lift control system by password

1. When input the password and unlock the door.

2. Lift will go down to outdoor station floor.

3. Visitor can only press lift floor key which related to this password.

Building outdoor station


04 Lift control3. Unlock to activate lift control system by password

1. When departure floor indoor station do intercom, arrival floor indoor station presses “Elevator authorization”.

2. Lift will go to departure floor.

3. Visitor can only press lift floor key which related to arrival floor.

Authorization by indoor stations intercom

05 Card reader


05 Card readerCommissioning

1. Select working mode.

3. Parameter setting

2. Set identifier.

4. Wiring.


05 Card reader 1. Select working mode

1. Open the back cover of the card reader.2. Set the dip switch position 1:

OFF – Building card reader modeON – Public card reader mode.



05 Card reader 2. Set Identifier

1. Open the back cover of the card reader, address rotary switch.

2. Set the address of card reader:Building card reader: by setting the address rotary switch directly from 1 – 9.Public card reader:Address 1 – 9: Setting by address rotary switch. Address 10-32: Set address rotary switch as 0, and using remote to set from 10 - 32 (Press “FN + CLERA + xx+ ENTER”)


05 Card reader 3. Parameter setting

1. Set Building card reader’s Building No. (1-999):

Using a remote: FN + ENTER + (building No. 1-999) + ENTER.



05 Card reader 4. Wiring

1. Cable connection as below:LAN cable connect with card reader TX- ---- OrangeTX+ ---- Orange and whiteRX- ---- Green RX+ ---- Green and white

DC+, GND ---- Power supplyUNLOCK,GND ---- Door open buttonNO,NC,COM ---- LockGS, GND ---- Door status check


GS ASK NO COMULK GND NC

GND LA RX+ TX+DC+ LB RX- TX-


05 Card readerapplication

Enter setting status

Card management

Password Modification

05 Card reader


1. Point the infrared remote controller to card reader.

2. Enter ”FN”+”system password”+”Enter” to enter engineering mode.

Notes:

1. During setting, press EXIT button can return to the previous menu or exit the setting.

2. If the operation succeeds during setting, the card reader will sound a long beep and the green indicator will flicker slowly. If fails, there will be a three short beep.

Enter setting status

05 Card reader


Resident card registration

Register by Card No (lift control function disable): “FN”+”1”+Card No+”Enter”;

Register by Card reading (lift control function disable): “FN”+”2”+Reading cards continuously;

Register by Card No (lift control function enable): “FN”+”1”+Card No+”Lift”+*Floor No+”Enter”;

Register by Card reading (lift control function enable): “FN”+”2”+ Reading cards +”Lift”+*Floor No+”Enter”;

* If the floor No. is below zero, input “FN” +floor No.

RF card management

Delete single card by card No.:

“FN”+”5”+Card No+”CLEAR”

Delete multi cards by card reading:

“FN”+”6”+Reading cards continuously

Delete all resident cards:

“FN”+”8”+”CLEAR”

Notes: 1. The RF card No.shall within 10 digits;

2. If the operation succeeds, the Card Reader will sound a long beep.

RF card management

05 Card reader


Password modification:

“FN”+”9”+New password+”ENTER”+Newpassword+”Enter

Note: The password must be 6 digits.

Password Modification



05 Commissioning

1. Precondition setting.

Commissioning



Precondition: PC must be set to obtain IP address automatically.

Destination: To set static IP address with exist IP address information.

Double click network connection icon to enter the “Network Connection Status” window. Click “Detail”.

On “Network Connection status” window. It will show IP details got from the router. These IP information will be used later.

1. Precondition setting

1 2

Commissioning



Back to “Network Connection Status” window, click “Properties”.

On “Network Connection Properties” window, select “TCP/IPv4”, click “Properties”.

On “TCP/IPv4 Properties” window, please select “Use the following IP address”, then input IP information you recorded before.

At last, please click “Advance”, on the pop-up window, input new IP address and subnet mask.

IP address: 10.0.0.1


1 2 3 4

5

Commissioning



2. If IP connects to router by wireless network connection. Disable “Local Area Connection”.

If PC connects to router by cable. Disable “Wireless Network connection”.

3. Enable ports of PC firewall

Make sure the following ports are enabled by PC firewall (Window Firewall or 3rd-party anti-virus software):

TCP: 7000, 7005, 7006, 7070, 7554, 7660, 7777, 8554;

UDP: 3333, 3339, 4444, 6999.


1

2

Commissioning



Example of setting Window firewall.

Following is an example for setting Window firewall.

When starting the software the first time, Window firewall will pop up a notification. Confirm the path name includes “abb-welcome”, then click “Allow access”


Commissioning



It is recommend to check “Windows firewall inbound Rules” to see if the application is enable by Windows firewall successfully.



06 Property managementApplication

1. Text message

2. Communication

3. Surveillance

4. Alarm

5. Card registration and management

6. Indoor station remote picture setting

7. Emergency unlock

8. Staff management

9. Message management

Application



After login successfully, you can see “SMS” icon on the main page.

Click “SMS” on the main page.

There will be a list of SMS history, double click one piece of SMS to reply it.

1. Text message1

2

Application



1.1 Send message:

① Choose message type (bulletin of indoor station, private data, bulletin of outdoor station;

② Select receiver;

③ Fill in “title”, “content”, upload picture;

④ Click “submit”.

1. Text message

Application



1.2 Receive message

Click “detail” to read the message, and also can reply.

1. Text message

1

2

Application



After login successfully, you can see “Talking” icon on the main page.

Click “talking” on the main page.

This software can talking with other PC Guard unit, phone guard unit, indoor station.

2. Communication1

2

Application



2.1 initiate a call

Click “talking” on the main page.

1. Choose Device

2. Input device ID

3. Click to dial out.

4. During ringing or talking,

click to terminal.

Notes:

1. This software can talk with other PC Guard unit, phone guard unit, indoor station;

2. Device ID can input through computer keyboard, software keyboard, dial back via talk records.

2. Communication

1

2

Application



2.2 during communication

1. If there comes a call from outdoor station / gate station / indoor station / phone guard unit / other PC guard unit, click to answer the call.

2. During ringing or talking, click to terminal the call.

3. During ringing or talking, click to unlock the door.

2. Communication

Application



Click “survey” on the main page.

1. Input “device type” and “device ID” and then click to initiate surveillance.

2. During surveillance, click to terminal.

3. During surveillance, click to take snapshot.

4. Surveillance will end automatically after 15s.

Notes:

Device type can be door station, gate station.

3. Surveillance1

2

Application



4.1 Alarm dealing

After login successfully, you can see “Alarm” icon on the main page.

Click “alarm” on the main page.

There will be an alarm interface once comes a new alarm, click alarm notice to mute it, and double click alarm notice to enter alarm processing interface.

4. Alarm1

2

Application



5.1 Card registration

1. One by one;

2. From database;

3. From file;

Choose a file (only support txt, and only one card no in one line ), and click “submit”


1

23

Application



5.2 Card management

1. Card list;

2. Card read;


1

2

Application



6. Device remote upgrade1

Application



6. Indoor station remote picture setting

Application



Input password* click “confirm to unlock all doors.

7. Emergency unlock


Application



1. Department management;

2. Add new staff;

3. Staff list;

8. Staff management;1

2

3

Application



1. Info. Search;

2. Delete message;

9. Message management1

2

Documents

ABB-Welcome IP · Plan x to input project structure picture. 1. 2. ... Slide 29. 1. IP Camera monitor via management software. ... input programming password