Abbreviated TERMINAL commands for 4100ES (Press ENTER for prompt (-) before typing a commandHELP (shows a list of all the commands)

CT*IME CL*IST REV*ISION TERM*INAL T*IME A*CKS*ET BYP*ASS DIS*ABLE DISARM HELP LOG*INRES*TART SH*OW L*IST PRINT TYPE SELECTCLEAR DIAG*NOSTIC WALK*TEST CS*HOW TIC*MODE SWAPSYS*DIAG CHD*IAG SCC IMODE /P

An * denotes the minimum number of letters to be typed. In the help screens, anitem surrounded by square brackets "[ ]" is optional.REV*ISION (Show current Revision, CFIG Format, Filename, Rev and date of downloaded file)

SYS REV 11.03 CFIG Format: 6 Job: Testsys Rev:12 23-Jan-03 7:26

REV ALL (shows the revision status of every card)REV HW (shows the revision of all the hardware)

T*IME (Use to show time or set the time)

T -Display time/dateT 8:00 -Set time to 8:00am, todayT 25-DEC-06 -Set date to December 25, current timeT 8:00 25-DEC-06 -Set time to 8:00 and date to December 25, 2006

A*CK (Acknowledge a single point or a group of points)

A T (Acknowledge all Troubles if a Global System)A F (Ack all fires)A P (Ack all Pri2)A S (Ack all Supervisories)

LOG*IN (Allow logging in to the current port)

Enter your Passcode or ENTER to Logout(Password is not displayed as you type)

ACCESS GRANTED

S*ET (Change the status and/or priority of a point) (requires default access level 3)S SIG3 ON S SIG3 OFFS SIG3 PRI=7 (2-15)S M1-4 ROR=3 (3, 15, 20)S M1-5 SENS=3.0 (0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.7 for photo) (If ION use 0.5, 0.9, 1.3)

DIS*ABLE (Disable/enable points in the system) (requires default access level 3)DIS M1-5 ONDIS M1-5 OFF

IMODE (Install mode – adds or removes points or cards from Install mode (requires default access level 3) To add points: IMODE 3-8 (card address), IMODE M1-3, IMODE miss*ing devices, IMODE open* circuits To remove points: IMODE 3-8 off, IMODE M1-3 off, IMODE normal off, IMODE all off

(Use L I*MODE) to list all points in IMODE)

Silence = [CTL-S]Reset = [CTL-D]

International Trade Controls and RestrictionsThis material may contain information or technology the export or re-export of which is restricted by U.S. laws and regulations. By viewing this material, the recipient agrees to the following: (i) the recipient's use of the contents of this material shall comply with all applicable laws, rules and regulations, including, without limitation, U.S. international trade laws and regulations, and (ii) the recipient may not transfer or otherwise export or re-export any information or technology contained in this material except in full compliance with the export controls administered by the U.S. and other countries and any applicable import and use restrictions.

L*IST (Returns the current logical point status for the point ID requested)(default is ON state) L [<point>] [<qualifier>] (Qual: F=fire, P=PRI2, S=Supv, T=tbl, U=util, C=ctrl, D=disable, I=install) L (Returns all ON status points) L M1-4 (IF M1-4 IS IN ALARM ) L F (lists all fire); L S (lists all Supv), L T (lists all TBLs), L C (lists all control pts ON) L I*MODE (lists all points in IMODE)SH*OW (Shows ports, topology, nodes, counts or cards) SH M1-3 (shows all characteristics of a point) SH CARDS (Shows all cards in the system) SH CARDSTATUS [n] (Shows the detailed status of all the parameters of card [n] SH CARDSTATUS 4 (shows the XPS status) SH COUNTS (see example below)

FIRE = 2 PRIORITY2 = 0 SUPERVISORY = 0 TROUBLE = 5 SH PORTS (See example below)

Port 1 CRT80UPort 2 COMMAND*

SH SN (Shows the panel serial number)TYPE ALOG -Sends Alarm Historical Log out this port. TLOG -Sends Trouble Historical Log out this port. TASTAT*US -Sends TrueAlarm Status Report out this port. TASERV*ICE -Sends TrueAlarm Service Report out this port. IDNET CFIG -Sends IDNet+ configuration report out this port. TALTCD -Sends TrueAlert Candela Report out this port. TALTST*AT [<qual> (ALL, LAST)] -Sends TrueAlert Status Report out this port. TACO*SERV -Sends TrueAlarm CO Report out this port. ALMTALLY -Sends Alarm Verification TALLY out this port. (Rev 12.06.02, 14.01.05)CLEAR ALOG -Clears the Alarm Historical Log. TLOG -Clears the Trouble Historical Log. TALLY <PID> -Clears Alarm Verification Tally for point <PID>. PEAK <PID> -Clears Peak Analog Value for point <PID>.WALK*TEST (Starts or stops Walktest) (requires default access level 3) WALK 0 ON LOG NONE SIG WALK 0 OFFSYS*DIAG (Runs a system diagnostic function) (level 3)SYS NAC ALL (All NACs miswiring test)SYS NAC 1 (NAC miswiring test on address 1)

SYS DUP (For IDNet+ card) See other SYSSYS WEAK “SYS CFIG “

SYS PSIL ON – silences remote annunSYS PSIL OFF – turns off silence on remote annun

SYS EFS 1 E (Earth Fault Search on SPS)SYS EFS M1 (Earth Fault Search on IDNet M1)

SYS EFL (Turns ON Earth Fault Latch)SYS NOEFL (Turns OFF Earth Fault Latch)SYS EARTH (Shows Earth Fault status)

SYS IP (displays IP and MAC addresses in system)SYS PING <address> - network pings an address

SYS COALGO OFF/ON – disables IDNet CO algorhythmsSWAP (Swaps the alternate CFG for the primary CFG) (Must be at Level 4)

RES*TART (Warm or Cold start the panel) (Level 4) RES WARM RES COLDTIC*MODE (Disable or enable local mode operation) TIC NOLOCAL 11 (turns it OFF) TIC LOCAL 11 (turns it back ON)SMPL (used to view or log SMPL information) (added Rev 1.02.01) (Must be at level 3)

SMPL [LOG | NOLOG] <CHANGE | TRIG | DEFAULT> SMPL LOG – enables logging or viewing logging status (logging stays ON until you type “SMPL NOLOG” SMPL LOG CHANGE – shows equations that have undergone a status change SMPL LOG TRIG – shows equations to which a change in state has occurred to one of its inputs SMPL NOLOG – disables logging or viewing of logging status SMPL NOLOG DEFAULT – disables logging or viewing of default program equations (Prog 0 and Prog 1)

SMPL SHOW <PROG – EQ> <TRUE | FALSE> SMPL SHOW 0-16 shows status of the specified equation (TRUE or FALSE) and lists the equation contents SMPL SHOW *-* TRUE (*=wildcard) shows all equations that are TRUE at the moment of the command