Abis Data Configuration

8/8/2019 Abis Data Configuration

1/17

Abis data configuration


2/17

Contents:

I- BSC side(data configuration)

I-1 IP address planning

I-2 steps of data configuration I-3 Commissioning

II- BTS side (data configuration)

II-1 Steps of the configuration

II-2 Commissioning


3/17

I-BSC side

In this step according to the RNP planning

we choose the subrack where is locate the

BTS. The PEUB and the SPU (XPU)should be locate on this subrack.


4/17


PEUB/ BCIM address:

For this bords we use 168 networksegment.the second digit calculated by thefollowing formula:subrackNo*20+unit ofslot No. Set the third digit to 0 for thePEUB and to the link group number for the

BCIM. Set the fourth digit to 1 for thePEUB and 2 for the BCIM.


5/17


MLPPP Local and Peer ADDR :

Set the ip addresses in the 172 network

segment. the second digit calculated bythe following formula:subrackNo*20+unit

of slot No. Set the third digit to the link

group number. Set the fourth to 1 for the

BSC and 2 for the BTS


6/17

I-2 stepsofdata configuration

Abis interface link mode:ADD MLPPPLNK: FN=2, SN=27, MLPPPGRP=1, LNKLST="1", E1T1LST=0",E1T1MODE=E1,

E1TSBITMAP=TS_1&TS_2&TS_3&TS_4&TS_5&TS_6&TS_7&TS_8&TS_9&TS_10&TS_11&T

S_12&TS_13&TS_14&TS_15&TS_16&TS_17&TS_18&TS_19&TS_20&TS_21&TS_22&TS_23&

TS_24&TS_25&TS_26&TS_27&TS_28&TS_29&TS_30&TS_31,LIPADDR="172.47.0.1",

PIPADDR="172.47.0.2", LQR=NO, PFC=YES, ACFC=YES, HCMP=YES, HCMPTYP=UDP+IP,

MCTYPE=LONG, PPPMUXEN=ON, AUTHMODE=NO, BEARTYP=BOTHSIGTRF;

BTS basic information:ADD BSCBTSINF:BTSTP=IBSC, BTSID=1003, BTSNM="BTS1003", FN=2, SN=4, SSN=1,ABISCAPOPTMSW=OFF, ABISOPTMCRCSW=OFF, ABISREVFRAMEPERIOD=3,

HIGHPW=NOHIGHPW, ABISREDUNDANCESW=OFF, INTRAFADAPFILTER=OFF;


7/17


OML link:ADD BTSOMLNK: BTSID=1003, SPUFN=2, IFBSN=27, LM=MLPPP,

BCIMIP="168.47.0.2", MLPPPGRP=0;

Signaling link:ADD BTSSIGLNK: BTSID=1003, SPUFN=2, IFBSN=27, LM=MLPPP,

BCIMIP="168.47.0.2", MLPPPGRP=0;

Traffic link:ADD BTSTRFLNK: BTSID=1003, SPUFN=2, IFBSN=27, LM=MLPPP,

BCIMIP="168.47.0.2", TRFLNKFLG=0, MLPPPGRP=0;


8/17


Cell and Sector:ADDCELL: BTSID=1003, FN=2, CN=1003, SCTIDLST="0", PNLST="88", SID=8704, NID=1,

PZID=1, LAC="0x102", LCN=1003, LSCTID="0", ASSALW1X=NO, ASSALWDO=NO,

IFBORDCELL=NO, REVRSSICARRASSNSW=OFF, DOAREVRSSICARRASSNSW=OFF,

DOAPRVPRIASSSW=OFF, DOMULTIBANDASSIGNSW=OFF,

AUTODWNFWDEQLCHANTHD=20, AUTODWNCOUNTTHD=600,UNBLKFWDEQLCHANTHD=40, DOUSERCOUNTTHD=20, DOAUTODWNCOUNTTHD=600,

DOUNBLKUSERCOUNTTHD=40, CTLAC="0xFFF";

NB:Weshould add cell for 1x and EVDO services. TheCell No

forthe EVDO start by 15xx.You mustseparatethe Sector ID Lists and Pseudo NoiseCode Lists

entered by commas.


9/17


carrierof local BSC:ADDCDMACH: CN=1003, SCTID=0, CRRIDLST="11", BNDCLS=BC800,

ARFCNLST="185", TYP=CDMA2000, IFBCDMACH=NO, CCLMFLG=NO,

ECCLMFLG=NO, IFTCDMACH=NO, AUTODWNCDMACH=NO;

ADDCDMACH: CN=1503, SCTID=0, CRRIDLST="18", BNDCLS=BC800,

ARFCNLST="308", TYP=EVDO, COLORCODE=1, SECTORID24="0x001007",

EVDOPROVER=RELEASEA, AUTODWNCDMACH=NO;

Add BTS:ADD BTS: BTSID=1003, OMCIP=129.11.99.235, BTSTP=DBS3900_CDMA;


10/17

I-3 Commissioning

Check the basic information:

LST BSCBTSINF

Check the BTS link:LST BTSLNK

LST BTS

Query the Cell and carrierr information:

LST CELL

LST CDMACH


11/17

II- BTS side (data configuration)

To achieve this step the transmission

between BSC and BTS must be up and

the BTS also must be power on. So it very

import to cooperate with the transmission

and site engineer.


12/17

II-1 Stepsofthe configuration

Basic information cfgCLR CBTSCFG: BTSID=1003;

SET CBTSINFO: BTSID=1003, BTSTP=CBTS, BTSCLASS=DBS3900_CDMA, CONFIRM=Y;

NB: BTS ID must be consistent withthe ID whichis already

configured in BSCside. (ADD BSCBTSINF).

UseCLR CBTSCFG to clearthe current configuration data of

the BTS .


13/17


Cell cfg:ADDCBTSCELL: BTSID=1003,LOCALCELLID=1003,LOCALSECTORID=0;

Basebande bord cfg:ADDCBTSCMPT: BTSID=1003,BRDID=0,CONFIRM=Y;

ADDCBTSUTRP:BTSID=1003,BRDID=4,CONFIRM=Y;

NB:CMPT correspond to BCKM onthe BTS 3606 and the UTRP to BCIM.

CE pool CE board cfg:ADDCBTSCPL:BTSID=1003,CPLID=0,CPLMODE=STATIC,CELLMODE=NORMAL;

ADDCBTSCPL:BTSID=1003,CPLID=1,CPLMODE=STATIC,CELLMODE=NORMAL;ADDCBTSCPL:BTSID=1003,CPLID=2,CPLMODE=STATIC,CELLMODE=NORMAL;ADDCBTSCPM: BTSID=1003,BRDID=2,CPLID=0;

ADDCBTSCPM: BTSID=1003,BRDID=3,CPLID=1;

ADDCBTSECM:BTSID=1003,BRDID=0,CPLID=2,WORKINGMODE=CHANNEL3_MODE;


14/17


MLPP transnission link cfg:ADDCBTSLNKGRP:BTSID=1003,BRDTP=UTRP,BRDID=4,LNKGRPID=0,LNKGRPTP=MLPPP;

ADDCBTSLNK:BTSID=1003,BRDTP=UTRP,BRDID=4,LNKID=0,LNKGRPID=0;


15/17


Signaling link and traffic link cfg:ADDCBTSTERSIGLNK:BTSID=1003,IPVER=IPV4,BSCIP="80.144.16.131",BTSIP="80.126.4.17

",BTSSNM="255.255.0.0",BRDTP=UTRP,BRDID=4,ABISLNKTP=CDMA1XONLY,BEARERTP=IP,P

ERIP="168.47.0.1",PROTOCOLTP=TCP;

ADDCBTSTERSIGLNK:BTSID=1003,IPVER=IPV4,BSCIP="80.144.16.131",BTSIP="80.126.4.17",BTSSNM="255.255.0.0",BRDTP=UTRP,BRDID=4,ABISLNKTP=CDMADOONLY,BEARERTP=IP,PE

ERIP="168.47.0.1",PROTOCOLTP=TCP;

ADDCBTSIPTERTRFLNK:BTSID=1041,IPLNKID=0,SVCTP=ALL,BRDTP=UTRP,BRDID=4,BUFFM

NUM=3,LNKLAYERTP=PPP,LNKGRPID=0;

NB: for each service we should configure a signaling link. One traffic link is used the both service.

Use LST BTSLNK to query BTSIP address for signaling link and LST SUBSYSTEM to query

BSCIP address.


16/17


RF module cfg:ADDCBTSTRM:BTSID=1003,TRMID=0,RCKTP=RRU,TRMDES="RRU0",MASTERBRD=CPM2,F

IBPN=0,FIBTS=0;

ADDCBTSSECTORCARRIER:BTSID=1003, LOCALCELLID=1, LOCALSECTORID=0, CRRID=0,

TRMID=0,CPLID=0,HPBFLG=NO;

NB: wehavethree RRUsto configure and eachoneis connecttooneoptical portofthe HCPM.

Start the BTS:STR CBTS: BTSID=1003;

Save the current configuration:SAV CBTSCFG: BTSID=1003;


17/17

II-2 Commissioning

Check the signaling link status

DSP SIGLNKSTAT

Check the resources status:DSP RES

unblock the resources:

UBL RES

Query CE information:

LST BSCBTSINF

Documents

Abis Data Configuration