Embed Size (px)
Citation preview
![Page 1: AC-DC Power Supplies Open Frame/Enclosed Type LDC15F LD C … · 2019. 10. 13. · VOLTAGE[V] AC85 - 264 1f or DC110 - 370 CURRENT[A] ACIN 100V 0.4typ (Io=100%) FREQUENCY[Hz] 47 -](https://reader035.pdfslide.net/reader035/viewer/2022071507/61284e363257da4ad2729b74/html5/thumbnails/1.jpg)
LDC-2
LDC
MODEL LDC15F-1 LDC15F-2
DC OUTPUTV1 +5V 2.0(Peak 3.0)A +5V 2.0(Peak 3.0)AV2 +12V 0.3(Peak 0.6)A +15V 0.3(Peak 0.6)AV3 -12V 0.2(Peak 0.3)A -15V 0.2(Peak 0.3)A
SPECIFICATIONSMODEL LDC15F-1 LDC15F-2
INPUT
VOLTAGE[V] AC85 - 264 1f or DC110 - 370CURRENT[A] ACIN 100V 0.4typ (Io=100%)
FREQUENCY[Hz] 47 - 440 or DCEFFICIENCY[%] ACIN 100V 70typ (Io=100%)
INRUSH CURRENT[A]ACIN 100V 25typ (Io=100%)
ACIN 200V 50typ (Io=100%)
LEAKAGE CURRENT[mA] 0.75max (60Hz, According to UL, CSA, VDE and DEN-AN)
OUTPUT
VOLTAGE[V] +5 +12 -12 +5 +15 -15CURRENT[A] *1 0 - 2.0 (Peak 3.0) 0 - 0.3 (Peak 0.6) 0 - 0.2 (Peak 0.3) 0 - 2.0 (Peak 3.0) 0 - 0.3 (Peak 0.6) 0 - 0.2 (Peak 0.3)
LINE REGULATION[mV] 20max 48max 48max 20max 60max 60maxLOAD REGULATION[mV] 100max 120max 120max 100max 150max 150max
RIPPLE[mVp-p]0 to +50C*2 100max 120max 120max 100max 120max 120max-10 - 0C*2 140max 160max 160max 140max 160max 160max
RIPPLE NOISE[mVp-p]0 to +50C*2 120max 150max 150max 120max 150max 150max-10 - 0C*2 160max 180max 180max 160max 180max 180max
TEMPERATURE REGULATION[mV]0 to +50C 50max 350max 350max 50max 350max 350max-10 to +50C 60max 420max 420max 60max 420max 420max
DRIFT[mV] *3 20max xx xx 20max xx xxSTART-UP TIME[ms] 100max (ACIN 85V, Io=100%)
HOLD-UP TIME[ms] 10typ (ACIN 85V, Io=100%), 20typ (ACIN 100V, Io=100%), 100typ (ACIN 200V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] Fixed Fixed Fixed Fixed Fixed FixedOUTPUT VOLTAGE SETTING[V] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75
PROTECTIONCIRCUIT ANDOTHERS
OVERCURRENT PROTECTION Works over 105% of rating and recovers automaticallyOVERVOLTAGE PROTECTION Works over 115% of rating by zener diode clamping (+5V only)
OPERATING INDICATION Not providedREMOTE SENSING Not providedREMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature)
OUTPUT-OUTPUT(V1-V2,V3) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature)
ENVIRONMENT
OPERATING TEMP.,HUMID.AND ALTITUDE -10 to +60C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet)
STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet)
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axisIMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY ANDNOISEREGULATIONS
AGENCY APPROVALS UL60950-1, EN60950-1, EN50178, CSA C22.2 No.60950-1 Complies with DEN-AN and IEC60950-1CONDUCTED NOISE Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B
OTHERSCASE SIZE/WEIGHT 50X26X127mm [1.97X1.02X5 inches] (WXHXD) /150g max (with chassis & cover : 300g max)
COOLING METHOD Convection
*1 Peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 16W, -2: 17.5W).When the load of +5V is OA, other output can be drawn by 80% of rated current.*2 Measured by 20MHz oscilloscope or Ripple-Noise meter (equivalent to KEISOKU-GIKEN:RM101).*3 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C with the input voltage held constant at the rated input/output.*4 Please contact us about safety approvals for the model with option.* Avoid prolonged use under over-load.* Derating is required when operated with chassis and cover.
LDC15FAC-DC Power Supplies Open Frame/Enclosed Type
LD C 15 F -1 -O
Ordering information
1Series name2Multiple output3Output wattage4Universal input5Output voltage combina-
tion6Optional *4
C :with CoatingG :Low leakage currentS :with ChassisSN :with Chassis & coverY :with Potentiometer
R
1 2 3 4 5 6
LDC
LDC-2
¡DERATING CURVE¡OVERCURRENT CHARACTERISTICS (LDC15F-1)
¡RISE TIME & FALL TIME (LDC15F-1)¡STATIC CHARACTERISTICS (LDC15F-1)
LDC
LDC-3
LDC15F
External view
¶ Weight: 150g max(with chassis & cover : 300g max)¶ Tolerance: t1[t0.04]¶ Dimensions in mm,[ ]=inches¶ PCB Material: Glass composite(CEM3)¶ Chassis and cover is optional.¶ Mounting torque: 0.6N·m(6.3kgf·cm)max
4- f3.5 [0.14]
f3.5 [0.14]
50 [ 1
.97]
57 [ 2
.24]28
.5 [ 1
.12]
23 [ 0
.91]
127 [5]
147 [5.79]
19 [0.95]
PCB t=1.6 [0.06]
3.5
[ 0.1
4]
3.5
[ 0.1
4]3.
5 [ 0
.14]
3max
[ 0.1
2]
3.5 [0.14]
10 [ 0.3
9]19
[ 0.7
5]
38 [ 1.5
0]
6 [0.24]
6 [0.24]
15 [ 0
.59]
f3.5 [0.14]
4.75
[ 0.1
9]43±0
.5 [ 1
.69]
120±0.5 [4.72]
135±0.5 [5.31]
135±0.5 [5.31]
25±0
.5 [ 0
.98]
Performance data
LDC_E.indd 2 15.6.18 5:11:43 PM
![Page 2: AC-DC Power Supplies Open Frame/Enclosed Type LDC15F LD C … · 2019. 10. 13. · VOLTAGE[V] AC85 - 264 1f or DC110 - 370 CURRENT[A] ACIN 100V 0.4typ (Io=100%) FREQUENCY[Hz] 47 -](https://reader035.pdfslide.net/reader035/viewer/2022071507/61284e363257da4ad2729b74/html5/thumbnails/2.jpg)
LDC-3
LDC
MODEL LDC15F-1 LDC15F-2
DC OUTPUTV1 +5V 2.0(Peak 3.0)A +5V 2.0(Peak 3.0)AV2 +12V 0.3(Peak 0.6)A +15V 0.3(Peak 0.6)AV3 -12V 0.2(Peak 0.3)A -15V 0.2(Peak 0.3)A
SPECIFICATIONSMODEL LDC15F-1 LDC15F-2
INPUT
VOLTAGE[V] AC85 - 264 1f or DC110 - 370CURRENT[A] ACIN 100V 0.4typ (Io=100%)
FREQUENCY[Hz] 47 - 440 or DCEFFICIENCY[%] ACIN 100V 70typ (Io=100%)
INRUSH CURRENT[A]ACIN 100V 25typ (Io=100%)
ACIN 200V 50typ (Io=100%)
LEAKAGE CURRENT[mA] 0.75max (60Hz, According to UL, CSA, VDE and DEN-AN)
OUTPUT
VOLTAGE[V] +5 +12 -12 +5 +15 -15CURRENT[A] *1 0 - 2.0 (Peak 3.0) 0 - 0.3 (Peak 0.6) 0 - 0.2 (Peak 0.3) 0 - 2.0 (Peak 3.0) 0 - 0.3 (Peak 0.6) 0 - 0.2 (Peak 0.3)
LINE REGULATION[mV] 20max 48max 48max 20max 60max 60maxLOAD REGULATION[mV] 100max 120max 120max 100max 150max 150max
RIPPLE[mVp-p]0 to +50C*2 100max 120max 120max 100max 120max 120max-10 - 0C*2 140max 160max 160max 140max 160max 160max
RIPPLE NOISE[mVp-p]0 to +50C*2 120max 150max 150max 120max 150max 150max-10 - 0C*2 160max 180max 180max 160max 180max 180max
TEMPERATURE REGULATION[mV]0 to +50C 50max 350max 350max 50max 350max 350max-10 to +50C 60max 420max 420max 60max 420max 420max
DRIFT[mV] *3 20max xx xx 20max xx xxSTART-UP TIME[ms] 100max (ACIN 85V, Io=100%)
HOLD-UP TIME[ms] 10typ (ACIN 85V, Io=100%), 20typ (ACIN 100V, Io=100%), 100typ (ACIN 200V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] Fixed Fixed Fixed Fixed Fixed FixedOUTPUT VOLTAGE SETTING[V] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75
PROTECTIONCIRCUIT ANDOTHERS
OVERCURRENT PROTECTION Works over 105% of rating and recovers automaticallyOVERVOLTAGE PROTECTION Works over 115% of rating by zener diode clamping (+5V only)
OPERATING INDICATION Not providedREMOTE SENSING Not providedREMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature)
OUTPUT-OUTPUT(V1-V2,V3) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature)
ENVIRONMENT
OPERATING TEMP.,HUMID.AND ALTITUDE -10 to +60C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet)
STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet)
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axisIMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY ANDNOISEREGULATIONS
AGENCY APPROVALS UL60950-1, EN60950-1, EN50178, CSA C22.2 No.60950-1 Complies with DEN-AN and IEC60950-1CONDUCTED NOISE Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B
OTHERSCASE SIZE/WEIGHT 50X26X127mm [1.97X1.02X5 inches] (WXHXD) /150g max (with chassis & cover : 300g max)
COOLING METHOD Convection
*1 Peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 16W, -2: 17.5W).When the load of +5V is OA, other output can be drawn by 80% of rated current.*2 Measured by 20MHz oscilloscope or Ripple-Noise meter (equivalent to KEISOKU-GIKEN:RM101).*3 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C with the input voltage held constant at the rated input/output.*4 Please contact us about safety approvals for the model with option.* Avoid prolonged use under over-load.* Derating is required when operated with chassis and cover.
LDC15FAC-DC Power Supplies Open Frame/Enclosed Type
LD C 15 F -1 -O
Ordering information
1Series name2Multiple output3Output wattage4Universal input5Output voltage combina-
tion6Optional *4
C :with CoatingG :Low leakage currentS :with ChassisSN :with Chassis & coverY :with Potentiometer
R
1 2 3 4 5 6
LDC
LDC-2
¡DERATING CURVE¡OVERCURRENT CHARACTERISTICS (LDC15F-1)
¡RISE TIME & FALL TIME (LDC15F-1)¡STATIC CHARACTERISTICS (LDC15F-1)
LDC
LDC-3
LDC15F
External view
¶ Weight: 150g max(with chassis & cover : 300g max)¶ Tolerance: t1[t0.04]¶ Dimensions in mm,[ ]=inches¶ PCB Material: Glass composite(CEM3)¶ Chassis and cover is optional.¶ Mounting torque: 0.6N·m(6.3kgf·cm)max
4- f3.5 [0.14]
f3.5 [0.14]
50 [ 1
.97]
57 [ 2
.24]28
.5 [ 1
.12]
23 [ 0
.91]
127 [5]
147 [5.79]
19 [0.95]
PCB t=1.6 [0.06]
3.5
[ 0.1
4]
3.5
[ 0.1
4]3.
5 [ 0
.14]
3max
[ 0.1
2]
3.5 [0.14]
10 [ 0.3
9]19
[ 0.7
5]
38 [ 1.5
0]
6 [0.24]
6 [0.24]
15 [ 0
.59]
f3.5 [0.14]
4.75
[ 0.1
9]43±0
.5 [ 1
.69]
120±0.5 [4.72]
135±0.5 [5.31]
135±0.5 [5.31]
25±0
.5 [ 0
.98]
Performance data
LDC_E.indd 3 15.6.18 5:11:43 PM
![Page 3: AC-DC Power Supplies Open Frame/Enclosed Type LDC15F LD C … · 2019. 10. 13. · VOLTAGE[V] AC85 - 264 1f or DC110 - 370 CURRENT[A] ACIN 100V 0.4typ (Io=100%) FREQUENCY[Hz] 47 -](https://reader035.pdfslide.net/reader035/viewer/2022071507/61284e363257da4ad2729b74/html5/thumbnails/3.jpg)
LDC-4
LDC
MODEL LDC30F-1 LDC30F-2
DC OUTPUTV1 +5V 3.0(Peak 4.5)A +5V 3.0(Peak 4.5)AV2 +12V 1.2(Peak 2.0)A +15V 1.0(Peak 2.0)AV3 -12V 0.3(Peak 0.45)A -15V 0.3(Peak 0.45)A
SPECIFICATIONSMODEL LDC30F-1 LDC30F-2
INPUT
VOLTAGE[V] AC85 - 264 1f or DC110 - 370CURRENT[A] ACIN 100V 0.8typ (Io=100%)
FREQUENCY[Hz] 47 - 440 or DCEFFICIENCY[%] ACIN 100V 72typ (Io=100%)
INRUSH CURRENT[A]ACIN 100V 25typ (Io=100%) (At cold start)
ACIN 200V 50typ (Io=100%) (At cold start)
LEAKAGE CURRENT[mA] 0.75max (60Hz, According to UL, CSA, VDE and DEN-AN)
OUTPUT
VOLTAGE[V] +5 +12 -12 +5 +15 -15CURRENT[A] *1 0 - 3.0 (Peak 4.5) 0 - 1.2 (Peak 2.0) 0 - 0.3 (Peak 0.45) 0 - 3.0 (Peak 4.5) 0 - 1.0 (Peak 2.0) 0 - 0.3 (Peak 0.45)
LINE REGULATION[mV] 20max 48max 48max 20max 60max 60maxLOAD REGULATION[mV] 100max 120max 150max 100max 120max 150max
RIPPLE[mVp-p]0 to +50C*2 100max 120max 120max 100max 120max 120max-10 - 0C*2 150max 160max 160max 150max 160max 160max
RIPPLE NOISE[mVp-p]0 to +50C*2 120max 150max 150max 120max 150max 150max-10 - 0C*2 170max 180max 180max 170max 180max 180max
TEMPERATURE REGULATION[mV]0 to +50C 50max 350max 350max 50max 350max 350max-10 to +50C 60max 420max 420max 60max 420max 420max
DRIFT[mV] *3 20max xx xx 20max xx xxSTART-UP TIME[ms] 100max (ACIN 85V, Io=100%)
HOLD-UP TIME[ms] 10typ (ACIN 85V, Io=100%), 20typ (ACIN 100V, Io=100%), 100typ (ACIN 200V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] Fixed Fixed Fixed Fixed Fixed FixedOUTPUT VOLTAGE SETTING[V] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75
PROTECTIONCIRCUIT ANDOTHERS
OVERCURRENT PROTECTION Works over 105% of rating and recovers automaticallyOVERVOLTAGE PROTECTION Works at 115 - 140% of rating (+5V only)
OPERATING INDICATION Not providedREMOTE SENSING Not providedREMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature)
OUTPUT-OUTPUT(V1-V2,V3) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature)
ENVIRONMENT
OPERATING TEMP.,HUMID.AND ALTITUDE -10 to +60C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet)
STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet)
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axisIMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY ANDNOISEREGULATIONS
AGENCY APPROVALS UL60950-1, EN60950-1, EN50178, CSA C22.2 No.60950-1 Complies with DEN-AN and IEC60950-1CONDUCTED NOISE Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B
OTHERSCASE SIZE/WEIGHT 65X26X140mm [2.56X1.02X5.51 inches] (WXHXD) / 220g max (with chassis & cover : 400g max)
COOLING METHOD Convection
*1 Peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 33W, -2: 34.5W).When the load of +5V is OA, other output can be drawn by 80% of rated current.*2 Measured by 20MHz oscilloscope or Ripple-Noise meter (equivalent to KEISOKU-GIKEN:RM101).*3 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C with the input voltage held constant at the rated input/output.*4 Please contact us about safety approvals for the model with option.* Avoid prolonged use under over-load.* Derating is required when operated with chassis and cover.
LDC30FAC-DC Power Supplies Open Frame/Enclosed Type
LD C 30 F -1 -O
Ordering information
1Series name2Multiple output3Output wattage4Universal input5Output voltage combina-
tion6Optional *4
C :with CoatingG :Low leakage currentS :with ChassisSN :with Chassis & coverY :with Potentiometer
R
1 2 3 4 5 6
LDC
LDC-4
¡DERATING CURVE¡OVERCURRENT CHARACTERISTICS (LDC30F-1)
¡RISE TIME & FALL TIME (LDC30F-1)¡STATIC CHARACTERISTICS (LDC30F-1)
LDC
LDC-5
LDC30F
External view
¶ Weight: 220g max(with chassis & cover : 400g max)¶ Tolerance: t1[t0.04]¶ Dimensions in mm,[ ]=inches¶ PCB Material: Glass composite(CEM3)¶ Chassis and cover is optional.¶ Mounting torque: 0.6N·m(6.3kgf·cm)max
4- f3.5 [0.14]
f3.5 [0.14]
65 [ 2
.56]
72 [ 2
.83]36
[ 1.4
2]
23 [ 0
.91]
140 [5.51]160 [6.30]
57.5 [2.26]
PCB t=1.6 [0.06]
4 [ 0
.16]
3.5
[ 0.1
4]3.
5 [ 0
.14]
3max
[ 0.1
2]
4 [0.16]
10 [ 0.3
9]19
[ 0.7
5]38 [ 1.5
0]
5 [0.20]
5 [0.20]
26 [ 1
.02]
2-f3.5 [0.14]
9.25
[ 0.3
6]57±0
.5 [ 2
.24]
132±0.5 [5.20]
150±0.5 [5.91]
150±0.5 [5.91]
20±0
.5[ 0
.79]
16 [ 0
.63]
40±0
.5[ 1
.57]
Performance data
LDC_E.indd 4 15.6.18 5:11:45 PM
![Page 4: AC-DC Power Supplies Open Frame/Enclosed Type LDC15F LD C … · 2019. 10. 13. · VOLTAGE[V] AC85 - 264 1f or DC110 - 370 CURRENT[A] ACIN 100V 0.4typ (Io=100%) FREQUENCY[Hz] 47 -](https://reader035.pdfslide.net/reader035/viewer/2022071507/61284e363257da4ad2729b74/html5/thumbnails/4.jpg)
LDC-5
LDC
MODEL LDC30F-1 LDC30F-2
DC OUTPUTV1 +5V 3.0(Peak 4.5)A +5V 3.0(Peak 4.5)AV2 +12V 1.2(Peak 2.0)A +15V 1.0(Peak 2.0)AV3 -12V 0.3(Peak 0.45)A -15V 0.3(Peak 0.45)A
SPECIFICATIONSMODEL LDC30F-1 LDC30F-2
INPUT
VOLTAGE[V] AC85 - 264 1f or DC110 - 370CURRENT[A] ACIN 100V 0.8typ (Io=100%)
FREQUENCY[Hz] 47 - 440 or DCEFFICIENCY[%] ACIN 100V 72typ (Io=100%)
INRUSH CURRENT[A]ACIN 100V 25typ (Io=100%) (At cold start)
ACIN 200V 50typ (Io=100%) (At cold start)
LEAKAGE CURRENT[mA] 0.75max (60Hz, According to UL, CSA, VDE and DEN-AN)
OUTPUT
VOLTAGE[V] +5 +12 -12 +5 +15 -15CURRENT[A] *1 0 - 3.0 (Peak 4.5) 0 - 1.2 (Peak 2.0) 0 - 0.3 (Peak 0.45) 0 - 3.0 (Peak 4.5) 0 - 1.0 (Peak 2.0) 0 - 0.3 (Peak 0.45)
LINE REGULATION[mV] 20max 48max 48max 20max 60max 60maxLOAD REGULATION[mV] 100max 120max 150max 100max 120max 150max
RIPPLE[mVp-p]0 to +50C*2 100max 120max 120max 100max 120max 120max-10 - 0C*2 150max 160max 160max 150max 160max 160max
RIPPLE NOISE[mVp-p]0 to +50C*2 120max 150max 150max 120max 150max 150max-10 - 0C*2 170max 180max 180max 170max 180max 180max
TEMPERATURE REGULATION[mV]0 to +50C 50max 350max 350max 50max 350max 350max-10 to +50C 60max 420max 420max 60max 420max 420max
DRIFT[mV] *3 20max xx xx 20max xx xxSTART-UP TIME[ms] 100max (ACIN 85V, Io=100%)
HOLD-UP TIME[ms] 10typ (ACIN 85V, Io=100%), 20typ (ACIN 100V, Io=100%), 100typ (ACIN 200V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] Fixed Fixed Fixed Fixed Fixed FixedOUTPUT VOLTAGE SETTING[V] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75
PROTECTIONCIRCUIT ANDOTHERS
OVERCURRENT PROTECTION Works over 105% of rating and recovers automaticallyOVERVOLTAGE PROTECTION Works at 115 - 140% of rating (+5V only)
OPERATING INDICATION Not providedREMOTE SENSING Not providedREMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature)
OUTPUT-OUTPUT(V1-V2,V3) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature)
ENVIRONMENT
OPERATING TEMP.,HUMID.AND ALTITUDE -10 to +60C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet)
STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet)
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axisIMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY ANDNOISEREGULATIONS
AGENCY APPROVALS UL60950-1, EN60950-1, EN50178, CSA C22.2 No.60950-1 Complies with DEN-AN and IEC60950-1CONDUCTED NOISE Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B
OTHERSCASE SIZE/WEIGHT 65X26X140mm [2.56X1.02X5.51 inches] (WXHXD) / 220g max (with chassis & cover : 400g max)
COOLING METHOD Convection
*1 Peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 33W, -2: 34.5W).When the load of +5V is OA, other output can be drawn by 80% of rated current.*2 Measured by 20MHz oscilloscope or Ripple-Noise meter (equivalent to KEISOKU-GIKEN:RM101).*3 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C with the input voltage held constant at the rated input/output.*4 Please contact us about safety approvals for the model with option.* Avoid prolonged use under over-load.* Derating is required when operated with chassis and cover.
LDC30FAC-DC Power Supplies Open Frame/Enclosed Type
LD C 30 F -1 -O
Ordering information
1Series name2Multiple output3Output wattage4Universal input5Output voltage combina-
tion6Optional *4
C :with CoatingG :Low leakage currentS :with ChassisSN :with Chassis & coverY :with Potentiometer
R
1 2 3 4 5 6
LDC
LDC-4
¡DERATING CURVE¡OVERCURRENT CHARACTERISTICS (LDC30F-1)
¡RISE TIME & FALL TIME (LDC30F-1)¡STATIC CHARACTERISTICS (LDC30F-1)
LDC
LDC-5
LDC30F
External view
¶ Weight: 220g max(with chassis & cover : 400g max)¶ Tolerance: t1[t0.04]¶ Dimensions in mm,[ ]=inches¶ PCB Material: Glass composite(CEM3)¶ Chassis and cover is optional.¶ Mounting torque: 0.6N·m(6.3kgf·cm)max
4- f3.5 [0.14]
f3.5 [0.14]
65 [ 2
.56]
72 [ 2
.83]36
[ 1.4
2]
23 [ 0
.91]
140 [5.51]160 [6.30]
57.5 [2.26]
PCB t=1.6 [0.06]
4 [ 0
.16]
3.5
[ 0.1
4]3.
5 [ 0
.14]
3max
[ 0.1
2]
4 [0.16]
10 [ 0.3
9]19
[ 0.7
5]38 [ 1.5
0]
5 [0.20]
5 [0.20]
26 [ 1
.02]
2-f3.5 [0.14]
9.25
[ 0.3
6]57±0
.5 [ 2
.24]
132±0.5 [5.20]
150±0.5 [5.91]
150±0.5 [5.91]
20±0
.5[ 0
.79]
16 [ 0
.63]
40±0
.5[ 1
.57]
Performance data
LDC_E.indd 5 15.6.18 5:11:46 PM
![Page 5: AC-DC Power Supplies Open Frame/Enclosed Type LDC15F LD C … · 2019. 10. 13. · VOLTAGE[V] AC85 - 264 1f or DC110 - 370 CURRENT[A] ACIN 100V 0.4typ (Io=100%) FREQUENCY[Hz] 47 -](https://reader035.pdfslide.net/reader035/viewer/2022071507/61284e363257da4ad2729b74/html5/thumbnails/5.jpg)
LDC-6
LDC
MODEL LDC60F-1 LDC60F-2
DC OUTPUTV1 +5V 5.0(Peak 7.0)A +5V 5.0(Peak 7.0)AV2 +12V 2.5(Peak 3.5)A +15V 2.0(Peak 3.5)AV3 -12V 0.5(Peak 0.7)A -15V 0.5(Peak 0.7)A
SPECIFICATIONSMODEL LDC60F-1 LDC60F-2
INPUT
VOLTAGE[V] AC85 - 264 1f or DC110 - 370CURRENT[A] ACIN 100V 1.4typ (Io=100%)
FREQUENCY[Hz] 47 - 440 or DCEFFICIENCY[%] ACIN 100V 72typ (Io=100%)
INRUSH CURRENT[A]ACIN 100V 30typ (Io=100%) (At cold start)
ACIN 200V 60typ (Io=100%) (At cold start)
LEAKAGE CURRENT[mA] 0.75max (60Hz, According to UL, CSA, VDE and DEN-AN)
OUTPUT
VOLTAGE[V] +5 +12 -12 +5 +15 -15CURRENT[A] *1 0 - 5.0 (Peak 7.0) 0 - 2.5 (Peak 3.5) 0 - 0.5 (Peak 0.7) 0 - 5.0 (Peak 7.0) 0 - 2.0 (Peak 3.5) 0 - 0.5 (Peak 0.7)
LINE REGULATION[mV] 20max 48max 48max 20max 60max 60maxLOAD REGULATION[mV] 100max 150max 150max 100max 150max 150max
RIPPLE[mVp-p]0 to +50C*2 100max 120max 120max 100max 120max 120max-10 - 0C*2 150max 160max 160max 150max 160max 160max
RIPPLE NOISE[mVp-p]0 to +50C*2 120max 150max 150max 120max 150max 150max-10 - 0C*2 170max 180max 180max 170max 180max 180max
TEMPERATURE REGULATION[mV]0 to +50C 50max 350max 350max 50max 350max 350max-10 to +50C 60max 420max 420max 60max 420max 420max
DRIFT[mV] *3 20max xx xx 20max xx xxSTART-UP TIME[ms] 200max (ACIN 85V, Io=100%)
HOLD-UP TIME[ms] 10typ (ACIN 85V, Io=100%), 20typ (ACIN 100V, Io=100%), 100typ (ACIN 200V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] Fixed Fixed Fixed Fixed Fixed FixedOUTPUT VOLTAGE SETTING[V] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75
PROTECTIONCIRCUIT ANDOTHERS
OVERCURRENT PROTECTION Works over 105% of rating and recovers automaticallyOVERVOLTAGE PROTECTION Works over 115% of rating by zener diode clamping (only available with V1, V2)
OPERATING INDICATION Not providedREMOTE SENSING Not providedREMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature)
OUTPUT-OUTPUT(V1-V2,V3) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature)
ENVIRONMENT
OPERATING TEMP.,HUMID.AND ALTITUDE -10 to +60C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet)
STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet)
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axisIMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY ANDNOISEREGULATIONS
AGENCY APPROVALS UL60950-1, EN60950-1, EN50178, CSA C22.2 No.60950-1 Complies with DEN-AN and IEC60950-1CONDUCTED NOISE Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B
OTHERSCASE SIZE/WEIGHT 83X26X185mm [3.27X1.02X7.28 inches] (WXHXD) / 300g max (with chassis & cover : 550g max)
COOLING METHOD Convection
*1 Peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 61W, -2: 62.5W).When the load of +5V is OA, other output can be drawn by 80% of rated current.*2 Measured by 20MHz oscilloscope or Ripple-Noise meter (equivalent to KEISOKU-GIKEN:RM101).*3 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C with the input voltage held constant at the rated input/output.*4 Please contact us about safety approvals for the model with option.* Avoid prolonged use under over-load.* Derating is required when operated with chassis and cover.
LDC60FAC-DC Power Supplies Open Frame/Enclosed Type
LD C 60 F -1 -O
Ordering information
1Series name2Multiple output3Output wattage4Universal input5Output voltage combina-
tion6Optional *4
C :with CoatingG :Low leakage currentS :with ChassisSN :with Chassis & coverY :with Potentiometer
R
1 2 3 4 5 6
LDC
LDC-6
¡DERATING CURVE¡OVERCURRENT CHARACTERISTICS (LDC60F-1)
¡RISE TIME & FALL TIME (LDC60F-1)¡STATIC CHARACTERISTICS (LDC60F-1)
LDC
LDC-7
LDC60F
External view
¶ Weight: 300g max(with chassis & cover : 550g max)¶ Tolerance: t1[t0.04]¶ Dimensions in mm,[ ]=inches¶ PCB Material: Glass composite(CEM3)¶ Chassis and cover is optional.¶ Mounting torque: 1.5N·m(16kgf·cm)max
5- f3.5 [0.14]
f4.5 [0.18]
83 [ 3
.27]
92 [ 3
.62]
46 [ 1
.81]
23 [ 0
.91]
185 [7.28]
210 [8.27]
40.75 [1.60]
PCB t=1.6 [0.06]
4 [ 0
.16]
4.5
[ 0.1
8]4.
5 [ 0
.18]
3max
[ 0.12
]
4 [0.16]
11 [ 0.4
3]
19 [ 0
.75] 38 [ 1
.50]
7 [0.28]
7 [0.28]
31 [ 1
.22]
2-f4.5 [0.18]
8 [ 0
.31]
39±0
.5 [ 1
.54]
75±0
.5 [ 2
.95]
111±0.5 [4.37]177±0.5 [6.97]
195±0.5 [7.68]
195±0.5 [7.68]
30±0
.5[ 1
.18]
21 [ 0
.83]
50±0
.5[ 1
.97]
Performance data
LDC_E.indd 6 15.6.18 5:11:47 PM
![Page 6: AC-DC Power Supplies Open Frame/Enclosed Type LDC15F LD C … · 2019. 10. 13. · VOLTAGE[V] AC85 - 264 1f or DC110 - 370 CURRENT[A] ACIN 100V 0.4typ (Io=100%) FREQUENCY[Hz] 47 -](https://reader035.pdfslide.net/reader035/viewer/2022071507/61284e363257da4ad2729b74/html5/thumbnails/6.jpg)
LDC-7
LDC
MODEL LDC60F-1 LDC60F-2
DC OUTPUTV1 +5V 5.0(Peak 7.0)A +5V 5.0(Peak 7.0)AV2 +12V 2.5(Peak 3.5)A +15V 2.0(Peak 3.5)AV3 -12V 0.5(Peak 0.7)A -15V 0.5(Peak 0.7)A
SPECIFICATIONSMODEL LDC60F-1 LDC60F-2
INPUT
VOLTAGE[V] AC85 - 264 1f or DC110 - 370CURRENT[A] ACIN 100V 1.4typ (Io=100%)
FREQUENCY[Hz] 47 - 440 or DCEFFICIENCY[%] ACIN 100V 72typ (Io=100%)
INRUSH CURRENT[A]ACIN 100V 30typ (Io=100%) (At cold start)
ACIN 200V 60typ (Io=100%) (At cold start)
LEAKAGE CURRENT[mA] 0.75max (60Hz, According to UL, CSA, VDE and DEN-AN)
OUTPUT
VOLTAGE[V] +5 +12 -12 +5 +15 -15CURRENT[A] *1 0 - 5.0 (Peak 7.0) 0 - 2.5 (Peak 3.5) 0 - 0.5 (Peak 0.7) 0 - 5.0 (Peak 7.0) 0 - 2.0 (Peak 3.5) 0 - 0.5 (Peak 0.7)
LINE REGULATION[mV] 20max 48max 48max 20max 60max 60maxLOAD REGULATION[mV] 100max 150max 150max 100max 150max 150max
RIPPLE[mVp-p]0 to +50C*2 100max 120max 120max 100max 120max 120max-10 - 0C*2 150max 160max 160max 150max 160max 160max
RIPPLE NOISE[mVp-p]0 to +50C*2 120max 150max 150max 120max 150max 150max-10 - 0C*2 170max 180max 180max 170max 180max 180max
TEMPERATURE REGULATION[mV]0 to +50C 50max 350max 350max 50max 350max 350max-10 to +50C 60max 420max 420max 60max 420max 420max
DRIFT[mV] *3 20max xx xx 20max xx xxSTART-UP TIME[ms] 200max (ACIN 85V, Io=100%)
HOLD-UP TIME[ms] 10typ (ACIN 85V, Io=100%), 20typ (ACIN 100V, Io=100%), 100typ (ACIN 200V, Io=100%)
OUTPUT VOLTAGE ADJUSTMENT RANGE[V] Fixed Fixed Fixed Fixed Fixed FixedOUTPUT VOLTAGE SETTING[V] 4.9 to 5.3 11.4 to 12.6 -11.4 to -12.6 4.9 to 5.3 14.25 to 15.75 -14.25 to -15.75
PROTECTIONCIRCUIT ANDOTHERS
OVERCURRENT PROTECTION Works over 105% of rating and recovers automaticallyOVERVOLTAGE PROTECTION Works over 115% of rating by zener diode clamping (only available with V1, V2)
OPERATING INDICATION Not providedREMOTE SENSING Not providedREMOTE ON/OFF Not provided
ISOLATION
INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature)
OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature)
OUTPUT-OUTPUT(V1-V2,V3) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature)
ENVIRONMENT
OPERATING TEMP.,HUMID.AND ALTITUDE -10 to +60C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet)
STORAGE TEMP.,HUMID.AND ALTITUDE -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet)
VIBRATION 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axisIMPACT 196.1m/s2 (20G), 11ms, once each X, Y and Z axis
SAFETY ANDNOISEREGULATIONS
AGENCY APPROVALS UL60950-1, EN60950-1, EN50178, CSA C22.2 No.60950-1 Complies with DEN-AN and IEC60950-1CONDUCTED NOISE Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B
OTHERSCASE SIZE/WEIGHT 83X26X185mm [3.27X1.02X7.28 inches] (WXHXD) / 300g max (with chassis & cover : 550g max)
COOLING METHOD Convection
*1 Peak load for 10sec. or less is acceptable if the total wattage is less than the rated wattage(-1: 61W, -2: 62.5W).When the load of +5V is OA, other output can be drawn by 80% of rated current.*2 Measured by 20MHz oscilloscope or Ripple-Noise meter (equivalent to KEISOKU-GIKEN:RM101).*3 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C with the input voltage held constant at the rated input/output.*4 Please contact us about safety approvals for the model with option.* Avoid prolonged use under over-load.* Derating is required when operated with chassis and cover.
LDC60FAC-DC Power Supplies Open Frame/Enclosed Type
LD C 60 F -1 -O
Ordering information
1Series name2Multiple output3Output wattage4Universal input5Output voltage combina-
tion6Optional *4
C :with CoatingG :Low leakage currentS :with ChassisSN :with Chassis & coverY :with Potentiometer
R
1 2 3 4 5 6
LDC
LDC-6
¡DERATING CURVE¡OVERCURRENT CHARACTERISTICS (LDC60F-1)
¡RISE TIME & FALL TIME (LDC60F-1)¡STATIC CHARACTERISTICS (LDC60F-1)
LDC
LDC-7
LDC60F
External view
¶ Weight: 300g max(with chassis & cover : 550g max)¶ Tolerance: t1[t0.04]¶ Dimensions in mm,[ ]=inches¶ PCB Material: Glass composite(CEM3)¶ Chassis and cover is optional.¶ Mounting torque: 1.5N·m(16kgf·cm)max
5- f3.5 [0.14]
f4.5 [0.18]
83 [ 3
.27]
92 [ 3
.62]
46 [ 1
.81]
23 [ 0
.91]
185 [7.28]
210 [8.27]
40.75 [1.60]
PCB t=1.6 [0.06]
4 [ 0
.16]
4.5
[ 0.1
8]4.
5 [ 0
.18]
3max
[ 0.12
]
4 [0.16]
11 [ 0.4
3]
19 [ 0
.75] 38 [ 1
.50]
7 [0.28]
7 [0.28]
31 [ 1
.22]
2-f4.5 [0.18]
8 [ 0
.31]
39±0
.5 [ 1
.54]
75±0
.5 [ 2
.95]
111±0.5 [4.37]177±0.5 [6.97]
195±0.5 [7.68]
195±0.5 [7.68]
30±0
.5[ 1
.18]
21 [ 0
.83]
50±0
.5[ 1
.97]
Performance data
LDC_E.indd 7 15.6.18 5:11:48 PM
![AC/DC SWITCHING POWER SUPPLY INPUT: 85~132VAC TRIPLE OUTPUT 8 WATTS ERS … · 2014. 8. 11. · Input Voltage Vac AC 100 V[DC 130 V] Input Voltage Range Vdc AC85~132V [DC110-175V]](https://img.pdfslide.net/doc/110x75/5fc9742a355705549e03215c/acdc-switching-power-supply-input-85132vac-triple-output-8-watts-ers-2014-8.jpg)
![AC-DC Power Supplies Enclosed Type PBA10F PB A 10 FVOLTAGE[V] AC85 -2 64 1f or DC110-370 (AC50 or DC70 Please refer to the instruction manual 2.1 Inputv oltage *3) CURRENT[A] ACIN](https://img.pdfslide.net/doc/110x75/61285006db8f6b3ebb16ef3c/ac-dc-power-supplies-enclosed-type-pba10f-pb-a-10-f-voltagev-ac85-2-64-1f-or.jpg)