Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Accessing
KEPServe
To configu
Select the
After sele
g Allen Bradle
rEX
ure EQ7000 f
e serial port th
ecting the righ
y DH+ PLC 5 a
irst start the
hat the USB o
ht serial port c
and SLC 504 w
EQ32 configu
occupies unde
click on Confi
with EQ7000
uration softwa
er your Devic
igure.
using Ethern
are, and sele
ce Manager.
et IP Driver fr
ct EQ7000.
rom Kepwaree
Click on N
Select you
Next
ur network MMode DH+ or DDH485.
Select a u
Select the
nique node a
e network spe
address for th
eed.
he EQ7000.
Click on N
Enter an I
Next.
P address forr the EQ7000,, and the Nett mask as well as the Gatew
way.
Click on fi
Press on t
Once you
on OK
nish.
the Configure
have downlo
e push button
oaded OK to t
n switch on th
the EQ7000 y
he right hand
you should ge
side of the u
et the Success
nit and click O
s message sho
OK.
own below click
Start KEPS
Add New
Name the
Server.
Channel.
e Channel.
From Dev
Click on N
Select Net
vice Driver sel
Next
twork adapte
lect Allen Bra
er and click N
dley ControlL
ext.
Logix Etherne
et.
Select opt
Choose ho
Click on N
timization me
ow to handle
Next.
ethod, Duty C
non‐normali
Cycle and click
ized floating p
k on Next.
point values.
Click on N
Click On F
Click on w
Next.
Finish.
where it says CClick to add a device.
Name the
To access
Click on N
e Device and c
PLC5 under D
Next.
click Next.
Device model select DH+ G
Gateway : PLC
C‐5
Enter <IP
(dec)> as
Select Sca
Click Next
or Hostname
s shown
an Mode.
t
e>,1,[<Option
<IP address
al Routing Pa
s of the EQ70
ath>],<DHRIO
000>,0,0.A.PLC
O Slot>.<DHRIO
C5 node addr
O Channel>.<
ress in decima
<DH+ Node ID
al
D
Enter Com
Click Next
Select Dat
mmunication
t.
tabase and ac
timing param
ction required
meters.
d.
Make sure
Make sure
Click to ad
e port is set t
e your setting
dd tags.
o 44818, and
gs are right an
d select maxim
nd click on fin
mum number
nish.
r of bytes per request, andd click Next.
In this exa
Click on A
Click to ad
ample we add
Apply
dd new Tag.
ded Integer file N7 to readd 10 words sta
arting from wword 0.
Repeating
Click on A
Repeat th
g the proced
Apply
he procedure
ure for Floati
for Binary file
ng point file F
e B3.
F8.
Click on Lunch OPC Quuick Client
Click on th
Below we
he device to r
e will repeat t
read the tag v
he procedure
values as show
e for the SLC 5
wn below.
504, add a neew device and
d name it.
From Dev
Click Next
Enter Dev
vice Model, se
t.
vice ID similar
elect DH+ Gat
r to previously
teway : SLC 5/
y done for PL
/04
LC5 except he
ere the node aaddress for our SLC5/04 iss 3.
Here we aadded same ttags for the SLLC 5/04, N7, F
F8, and B3.
Lunch OPC Quick Client.