Upload
hoangdien
View
219
Download
0
Embed Size (px)
Citation preview
IMPORTANTCarefully examine the carton(s) for damage. If the cartonis damaged, immediately notify the shipping company.
DOOR WIDTH DOOR HEIGHT
PLEASE READ ALL INSTRUCTIONS BEFOREPROCEEDING WITH INSTALLATION.
❏ Wall Mount❏ Header Mount
Overhead Bracket Mount
❏ 12'' ❏ 18'' ❏ 24''– Projection –
Opens to:
❏ One Side
❏ Bi-Parting
800•888•9750
5350 Campbells Run Road • Pittsburgh, PA 15205-9738 • 412.787.9750 Fax: 412.787.3665 • Web Site: www.tmi-pvc.com • E-Mail: [email protected]
OTHER TMI PRODUCTS
MEGA-PRO™SWINGING DOORS
BULK PVCFILM • STRIP • SHEET • PANEL
SCREENS, CURTAINSand ENCLOSURES
DOCK ACCESSORIES
STRIP DOORS
AIR DOORS
Copyright © 2007 TMI, LLC Catalog No. II-TMIASD 06-07
INSTALLATION INSTRUCTIONS
Your Accordion Strip Door has been custom built to your specifica-tions. Those specifications should be clearly marked on the cover ofthese installation instructions.
We highly recommend that the unit be mounted on the interior side of thedoorway opening, basically to keep the mechanism out of the weather.
There are 3 different mounting methodsthat can be used: Wall Mount, HeaderMount and Overhead Bracket Mount . . . . and each of
these allowsthe door tobe pulled toOne Side orBi-Part.
WallMount
Pages2 - 5
Pages6 - 9
Pages10 - 13
HeaderMount
OverheadDoor Mount
One Side
Bi-Parting
MOUNTING METHODS
WALL MOUNTING Opening to One Side and Bi-Parting
With Multiple Sliding Tracks:Loosely place the supplied set screwsinto the splice connector. Place eachsliding track into the ends of the connec-tor and tighten the set screws. Now thecombined track can be treated as a sin-gle sliding track.
With a Single Sliding Track:First, place all of the wall hangers on thetrack. The two end hangers should beapproximately 8'' in from either end of thetrack and the remaining hangers shouldbe evenly spaced across the entire lengthof the track.
SLIDING TRACK
WALL SPLICECONNECTOR
SET SCREWS
SLIDING TRACK
2
8''
8''
Do not remove protective wrap from linkage assemblyuntil it is installed into the sliding track. The assemblyopens and closes in a scissorlike fashion. Serious injurymay result from failure to follow directions.
WARNING :
11
NOTES
First, remove each Retaining Bar from theeach Mounting Strip by unscrewing thenuts from the studs. NOTE: There are 2nut /bolt combinations in the center of eachstrip.
Then place the PVC Strips onto the studs.Replace the Retaining Strips and fastenwith the nuts.
With all the PVC Strips in place, yourSave-T Accordion Strip Door is complete.
After the assembled unit has been mounted using one of the3 mounting methods, the PVC strips must be attached to theAccordion Assembly.
PVC STRIP PLACEMENT
A Velcro® strip should already be attachedto the top of the Support Tube. However,the supplied pressure sensitive Velcro®
will have to be attached to the top of eachBracket and the Back Brace Tube, as wellas the corresponding areas on the coveritself.
Measure and cut both sides of thePVC cover accordingly, to accommo-date the overhead door rail andinside brace plate on the Bracket.Use a utility knife.
Once the Overhead Door Bracket, Accordion Assembly and Side Strips arein place and secured, the PVC cover should be placed over the top of theentire unit to create a substantial ambient air barrier.
NOTE: The method of applying the cover, described here, is quitegeneral since each overhead door and door rail configuration isdifferent for each manufacturer.
10
MOUNTING OVERHEAD DOOR COVER
DOORRAIL
PVC COVER
PVCCOVER
SUPPORTTUBE
BRACKETS andSUPPORT TUBES
VELCRO PLACEMENT
PVC COVERS
VELCROSTRIPS
BACKBRACE
TUBE
INSIDEBRACEPLATE
VELCRO
VELCRO
First, you must determine which side ofthe mechanism will be anchored to thesliding track and to which side the stripdoor will be drawn. If there are noobstructions, either side can be used.However, if there is an obstruction closeto the edge of the doorway opening,such as a wall or shelving, it would bebest to anchor the mechanism to thatside.
Remove the unit and drill the markedholes with the proper size drill. This is
determined by the material used in theconstruction of the header. If it’s wood, lag
screws can be used. If it’s concrete or concreteblocks, anchored lag screws will be necessary.
If the header is a steel plate, the hangers can beattached by welding.
Move each ofthe hangersslightly left orright, so thehanger will beattached to afirm portion ofthe wall. Markall the hangerplate holes.
Then, place the looselyassembled unit on the walljust above the header. Thebottom edge of the hangerplate should line up with theedge or lip of the header.
MARKHOLES
After the holes are drilled, attach the unit to the wall.
ANCHORBAR
ANCHOR
PULL DOORCLOSED TOTHIS SIDE
LIP OFHEADER
LIP OFHEADER
HANGERPLATE
MAGNETIC BRAKE ROLLERwith PULL ROPE
The next step is placing the Accordion Assembly into the sliding track.
6
5
43
3
For Bi-Parting Doors, skip to “WALL MOUNTING - Bi-Parting”, page 5)
CONCRETE orCONCRETE
BLOCK
STEEL
WOOD
To complete the installation, attach the flexible PVC strips tothe Accordion Assembly, see page 11.
With the unit compressed,slide each roller into thesliding track.
IMPORTANT: Be sure theanchor bar is facing theanchor side.
Attach the anchor bar to the slidingtrack using the end stop, anchorbolt and 3 anchor nuts.
NOTE: The Magnetic Brake & Pull RopeRoller is attached to the second cross-
member, opposite of the Anchor Bar. At thispoint, if you want to place the magnetic brake
roller at a different cross-member, exchange the rollermechanisms now.
IMPORTANT: The closer the Pull Rope is to the center of the accordionassembly, the more difficult it will be to completely close the door.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
CAUTION: Do notremove the protectivewrapping before placingassembly into slidingtrack.
ANCHORSIDE
ANCHORBOLT
ANCHORBAR
END STOP
NUTS
SLIDINGTRACK
4 9
For Closing to One Side usingSingle Accordion Assembly
With the assembly compressed, slide each rollerinto the sliding track.
NOTE: The anchor barcan be on either side . . .it’s your preference
For Bi-Parting Doors usingTwo Accordion Assemblies
With both assemblies compressed,slide each roller into thesliding track.
NOTE: The anchorbar for eachassemblyshould be on theoutside.
Attach each anchor bar to thesliding track using the end stop,anchor bolt and 3 anchor nuts.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
ANCHORBOLT
ANCHORBAR
END STOP
NUTS
SLIDINGTRACK
NOTE: The Magnetic Brake Roller & Pull Rope isattached to the second cross-member, opposite of
the Anchor Bar. At this point, if you want to place themagnetic brake roller at a different cross-member,exchange the roller mechanisms now.
IMPORTANT: The closer the Pull Rope is to the center of the accordionassembly, the more difficult it will be to completely close the door.
MAGNETIC BRAKE ROLLERwith PULL ROPE
CAUTION: Do not remove the protectivewrapping before placing assembly into
sliding track.
MAGNETICBRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
ANCHORBAR
OVERHEAD DOOR MOUNTINGOpening to One Side and Bi-Parting
Your Overhead Door Brackethas been shipped with theSliding Track Hangers alreadyattached to the Support Tube.
First, bolt the Support Tube to theMounting Brackets using themounting bolts, washers and nuts.
IMPORTANT: The hangers must be face down.
Next, attach the back Brace Tube to the MountingBrackets. The method of attachment is your choice.One way is to drill holes and use nuts, bolt & wash-ers; another is welding. We have given you thisoption because each door rail placement is different.
Next, place the assembled unit against the wallabove the doorway opening. With the bottom of eachPVC End Strip approximately 1/ 2” from the floor, levelthe unit and mark the mounting holes on the 2Mounting Brackets.
Then, mount the End Strips of PVC to the brackets.
NOTE: There are left andright brackets.
SLIDINGTRACK
PVC ENDSTRIPS
BACK BRACE TUBE
Remove the unit and drill the marked holes with theproper size drill. This is determined by the materialused in the construction of the wall. If it’s wood, lagscrews can be used. If it’s concrete or concreteblocks, anchored lag screws will be necessary. If theheader is a steel plate, the hangers can beattached by welding.
8
CONCRETE orCONCRETE BLOCK
STEEL
WOOD
To complete the installation, attach the flexible PVC strips tothe Accordion Assembly, see page 11.
Placeeach unit
so theAnchor Bar is
toward the end of thetrack and the Magnetic
Brake & Pull Rope Roller is toward the centerof the rail. Attach each anchor bar to the sliding track
using the end stops, anchor bolts and anchor nuts. (Seepage 4 ) Once the Anchor Bars are fastened to either end ofthe track, the assembly now can be attached to the wall.
With Multiple Sliding Tracks or SingleSliding Track: To begin mounting, refer tosteps 1 through 5 on pages 2 & 3.
IMPORTANT: After the holes are drilledand before attaching the unit to the wall,both Accordion Assemblies should beplaced into the sliding track.
WALL MOUNTING Bi-Parting Door
MAGNETIC BRAKE ROLLERwith PULL ROPE
CAUTION: Do not remove the protectivewrapping before placing assembly intosliding track.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
With this method the strip door isattached to the wall just above thedoorway opening. A Bi-PartingDoor is generally used becausethere are obstructions on bothsides of the doorway opening orthere is a desire to keep one halfof the doorway closed while trafficmoves through the opening.
ANCHORBAR
ANCHORBAR
ANCHOR
SHELVING
or WALL
SHELVING
or WALL
PULLLEFT
TOCLOSE
PULLRIGHT
TOCLOSE
ANCHOR
5
Remove the unit and drill the marked holes withthe proper size drill. This is determined by thematerial used in the construction of the header.If it’s wood, lag screws can be used. If it’s con-crete or concrete blocks, anchored lag screwswill be necessary. If the header is a steel plate,the hangers can be attached by welding.
Then place the assembled unitonto the header, between thedoor jambs. The hangershould be centered on thewidth of the header.
Mark the mounting holes on each of thehangers.
Finally, attach the assembled unit to theheader. To complete the installation, attachthe flexible PVC strips to the AccordionAssembly, see page 11.
HEADER MOUNTINGOpening to One Side and Bi-Parting
With Multiple Sliding Tracks:Turn the splice connector so the backing platefaces down. Loosen (do not remove) the 4clamp nuts. Place each sliding track (opengroove up) into the ends of the connectorand tighten the nuts. Now the com-bined track can be treated as asingle sliding track.
For Single Accordion Assembly – Closing to One Side:
With the assembly compressed, slide each rollerinto the sliding track.
NOTE: The anchor barcan be on either side . . .it’s your preference
For Two Accordion Assemblies –Bi-Parting
With both assemblies compressed,slide each roller into the slidingtrack.
NOTE: The anchorbar for eachassemblyshould be onthe outside.
With a Single Sliding Track:Loosen the 4 clamp nuts on allof the header hangers. Placeall the hangers on the slidingtrack. The two end hangers should be approximately 8'' in from eitherend of the track. The remaining hangers should be evenly spaced acrossthe entire length of the track. After positioning, tighten all the clamp nuts.
MARKHOLES
NOTE: Do not attach the unit to the headeruntil the Accordion Assembly is in place.
Attach each anchor bar to thesliding track using the end stop,anchor bolt and 3 anchor nuts.
CAUTION: The accordionassembly must be in thesliding track, completely
anchored, before it iswelded into place.
LOOSENCLAMP NUTS
LOOSENCLAMP NUTS
8''
8''
OPENGROOVE
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
6 7
OPENGROOVE
ANCHORBOLT
ANCHORBAR
END STOP
NUTS
SLIDINGTRACK
CAUTION: Do not remove the protectivewrapping before placing assembly into
sliding track.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORSIDE
ANCHORBAR
ANCHORBAR
CLAMPNUTS CLAMP
NUTS
CONCRETE orCONCRETE
BLOCK
STEEL
WOOD
Remove the unit and drill the marked holes withthe proper size drill. This is determined by thematerial used in the construction of the header.If it’s wood, lag screws can be used. If it’s con-crete or concrete blocks, anchored lag screwswill be necessary. If the header is a steel plate,the hangers can be attached by welding.
Then place the assembled unitonto the header, between thedoor jambs. The hangershould be centered on thewidth of the header.
Mark the mounting holes on each of thehangers.
Finally, attach the assembled unit to theheader. To complete the installation, attachthe flexible PVC strips to the AccordionAssembly, see page 11.
HEADER MOUNTINGOpening to One Side and Bi-Parting
With Multiple Sliding Tracks:Turn the splice connector so the backing platefaces down. Loosen (do not remove) the 4clamp nuts. Place each sliding track (opengroove up) into the ends of the connectorand tighten the nuts. Now the com-bined track can be treated as asingle sliding track.
For Single Accordion Assembly – Closing to One Side:
With the assembly compressed, slide each rollerinto the sliding track.
NOTE: The anchor barcan be on either side . . .it’s your preference
For Two Accordion Assemblies –Bi-Parting
With both assemblies compressed,slide each roller into the slidingtrack.
NOTE: The anchorbar for eachassemblyshould be onthe outside.
With a Single Sliding Track:Loosen the 4 clamp nuts on allof the header hangers. Placeall the hangers on the slidingtrack. The two end hangers should be approximately 8'' in from eitherend of the track. The remaining hangers should be evenly spaced acrossthe entire length of the track. After positioning, tighten all the clamp nuts.
MARKHOLES
NOTE: Do not attach the unit to the headeruntil the Accordion Assembly is in place.
Attach each anchor bar to thesliding track using the end stop,anchor bolt and 3 anchor nuts.
CAUTION: The accordionassembly must be in thesliding track, completely
anchored, before it iswelded into place.
LOOSENCLAMP NUTS
LOOSENCLAMP NUTS
8''
8''
OPENGROOVE
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
6 7
OPENGROOVE
ANCHORBOLT
ANCHORBAR
END STOP
NUTS
SLIDINGTRACK
CAUTION: Do not remove the protectivewrapping before placing assembly into
sliding track.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORSIDE
ANCHORBAR
ANCHORBAR
CLAMPNUTS CLAMP
NUTS
CONCRETE orCONCRETE
BLOCK
STEEL
WOOD
OVERHEAD DOOR MOUNTINGOpening to One Side and Bi-Parting
Your Overhead Door Brackethas been shipped with theSliding Track Hangers alreadyattached to the Support Tube.
First, bolt the Support Tube to theMounting Brackets using themounting bolts, washers and nuts.
IMPORTANT: The hangers must be face down.
Next, attach the back Brace Tube to the MountingBrackets. The method of attachment is your choice.One way is to drill holes and use nuts, bolt & wash-ers; another is welding. We have given you thisoption because each door rail placement is different.
Next, place the assembled unit against the wallabove the doorway opening. With the bottom of eachPVC End Strip approximately 1/ 2” from the floor, levelthe unit and mark the mounting holes on the 2Mounting Brackets.
Then, mount the End Strips of PVC to the brackets.
NOTE: There are left andright brackets.
SLIDINGTRACK
PVC ENDSTRIPS
BACK BRACE TUBE
Remove the unit and drill the marked holes with theproper size drill. This is determined by the materialused in the construction of the wall. If it’s wood, lagscrews can be used. If it’s concrete or concreteblocks, anchored lag screws will be necessary. If theheader is a steel plate, the hangers can beattached by welding.
8
CONCRETE orCONCRETE BLOCK
STEEL
WOOD
To complete the installation, attach the flexible PVC strips tothe Accordion Assembly, see page 11.
Placeeach unit
so theAnchor Bar is
toward the end of thetrack and the Magnetic
Brake & Pull Rope Roller is toward the centerof the rail. Attach each anchor bar to the sliding track
using the end stops, anchor bolts and anchor nuts. (Seepage 4 ) Once the Anchor Bars are fastened to either end ofthe track, the assembly now can be attached to the wall.
With Multiple Sliding Tracks or SingleSliding Track: To begin mounting, refer tosteps 1 through 5 on pages 2 & 3.
IMPORTANT: After the holes are drilledand before attaching the unit to the wall,both Accordion Assemblies should beplaced into the sliding track.
WALL MOUNTING Bi-Parting Door
MAGNETIC BRAKE ROLLERwith PULL ROPE
CAUTION: Do not remove the protectivewrapping before placing assembly intosliding track.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
With this method the strip door isattached to the wall just above thedoorway opening. A Bi-PartingDoor is generally used becausethere are obstructions on bothsides of the doorway opening orthere is a desire to keep one halfof the doorway closed while trafficmoves through the opening.
ANCHORBAR
ANCHORBAR
ANCHOR
SHELVING
or WALL
SHELVING
or WALL
PULLLEFT
TOCLOSE
PULLRIGHT
TOCLOSE
ANCHOR
5
To complete the installation, attach the flexible PVC strips tothe Accordion Assembly, see page 11.
With the unit compressed,slide each roller into thesliding track.
IMPORTANT: Be sure theanchor bar is facing theanchor side.
Attach the anchor bar to the slidingtrack using the end stop, anchorbolt and 3 anchor nuts.
NOTE: The Magnetic Brake & Pull RopeRoller is attached to the second cross-
member, opposite of the Anchor Bar. At thispoint, if you want to place the magnetic brake
roller at a different cross-member, exchange the rollermechanisms now.
IMPORTANT: The closer the Pull Rope is to the center of the accordionassembly, the more difficult it will be to completely close the door.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
CAUTION: Do notremove the protectivewrapping before placingassembly into slidingtrack.
ANCHORSIDE
ANCHORBOLT
ANCHORBAR
END STOP
NUTS
SLIDINGTRACK
4 9
For Closing to One Side usingSingle Accordion Assembly
With the assembly compressed, slide each rollerinto the sliding track.
NOTE: The anchor barcan be on either side . . .it’s your preference
For Bi-Parting Doors usingTwo Accordion Assemblies
With both assemblies compressed,slide each roller into thesliding track.
NOTE: The anchorbar for eachassemblyshould be on theoutside.
Attach each anchor bar to thesliding track using the end stop,anchor bolt and 3 anchor nuts.
MAGNETIC BRAKE ROLLERwith PULL ROPE
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
MAGNETIC BRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
ANCHORBOLT
ANCHORBAR
END STOP
NUTS
SLIDINGTRACK
NOTE: The Magnetic Brake Roller & Pull Rope isattached to the second cross-member, opposite of
the Anchor Bar. At this point, if you want to place themagnetic brake roller at a different cross-member,exchange the roller mechanisms now.
IMPORTANT: The closer the Pull Rope is to the center of the accordionassembly, the more difficult it will be to completely close the door.
MAGNETIC BRAKE ROLLERwith PULL ROPE
CAUTION: Do not remove the protectivewrapping before placing assembly into
sliding track.
MAGNETICBRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
MAGNETICBRAKE ROLLERwith PULL ROPE
ANCHORBAR
ANCHORBAR
ANCHORBAR
A hook and loop fastener strip should already be attached to the top of the Support Tube. However, the supplied pressure sensitive hook and loop will have to be attached to the top of each Bracket and the Back Brace Tube, as well as the corresponding areas on the cover itself.
Measure and cut both sides of thePVC cover accordingly, to accommo-date the overhead door rail andinside brace plate on the Bracket.Use a utility knife.
Once the Overhead Door Bracket, Accordion Assembly and Side Strips arein place and secured, the PVC cover should be placed over the top of theentire unit to create a substantial ambient air barrier.
NOTE: The method of applying the cover, described here, is quitegeneral since each overhead door and door rail configuration isdifferent for each manufacturer.
10
MOUNTING OVERHEAD DOOR COVER
DOORRAIL
PVC COVER
PVCCOVER
SUPPORTTUBE
BRACKETS andSUPPORT TUBES
HOOK AND LOOP PLACEMENT
PVC COVERS
HOOK & LOOPSTRIPS
BACKBRACE
TUBE
INSIDEBRACEPLATE
H&L
H&L
First, you must determine which side ofthe mechanism will be anchored to thesliding track and to which side the stripdoor will be drawn. If there are noobstructions, either side can be used.However, if there is an obstruction closeto the edge of the doorway opening,such as a wall or shelving, it would bebest to anchor the mechanism to thatside.
Remove the unit and drill the markedholes with the proper size drill. This is
determined by the material used in theconstruction of the header. If it’s wood, lag
screws can be used. If it’s concrete or concreteblocks, anchored lag screws will be necessary.
If the header is a steel plate, the hangers can beattached by welding.
Move each ofthe hangersslightly left orright, so thehanger will beattached to afirm portion ofthe wall. Markall the hangerplate holes.
Then, place the looselyassembled unit on the walljust above the header. Thebottom edge of the hangerplate should line up with theedge or lip of the header.
MARKHOLES
After the holes are drilled, attach the unit to the wall.
ANCHORBAR
ANCHOR
PULL DOORCLOSED TOTHIS SIDE
LIP OFHEADER
LIP OFHEADER
HANGERPLATE
MAGNETIC BRAKE ROLLERwith PULL ROPE
The next step is placing the Accordion Assembly into the sliding track.
6
5
43
3
For Bi-Parting Doors, skip to “WALL MOUNTING - Bi-Parting”, page 5)
CONCRETE orCONCRETE
BLOCK
STEEL
WOOD
Your Accordion Strip Door has been custom built to your specifica-tions. Those specifications should be clearly marked on the cover ofthese installation instructions.
We highly recommend that the unit be mounted on the interior side of thedoorway opening, basically to keep the mechanism out of the weather.
There are 3 different mounting methodsthat can be used: Wall Mount, HeaderMount and Overhead Bracket Mount . . . . and each of
these allowsthe door tobe pulled toOne Side orBi-Part.
WallMount
Pages2 - 5
Pages6 - 9
Pages10 - 13
HeaderMount
OverheadDoor Mount
One Side
Bi-Parting
MOUNTING METHODS
WALL MOUNTING Opening to One Side and Bi-Parting
With Multiple Sliding Tracks:Loosely place the supplied set screwsinto the splice connector. Place eachsliding track into the ends of the connec-tor and tighten the set screws. Now thecombined track can be treated as a sin-gle sliding track.
With a Single Sliding Track:First, place all of the wall hangers on thetrack. The two end hangers should beapproximately 8'' in from either end of thetrack and the remaining hangers shouldbe evenly spaced across the entire lengthof the track.
SLIDING TRACK
WALL SPLICECONNECTOR
SET SCREWS
SLIDING TRACK
2
8''
8''
Do not remove protective wrap from linkage assemblyuntil it is installed into the sliding track. The assemblyopens and closes in a scissorlike fashion. Serious injurymay result from failure to follow directions.
WARNING :
11
NOTES
First, remove each Retaining Bar from theeach Mounting Strip by unscrewing thenuts from the studs. NOTE: There are 2nut /bolt combinations in the center of eachstrip.
Then place the PVC Strips onto the studs.Replace the Retaining Strips and fastenwith the nuts.
With all the PVC Strips in place, yourSave-T Accordion Strip Door is complete.
After the assembled unit has been mounted using one of the3 mounting methods, the PVC strips must be attached to theAccordion Assembly.
PVC STRIP PLACEMENT
IMPORTANTCarefully examine the carton(s) for damage. If the cartonis damaged, immediately notify the shipping company.
DOOR WIDTH DOOR HEIGHT
PLEASE READ ALL INSTRUCTIONS BEFOREPROCEEDING WITH INSTALLATION.
❏ Wall Mount❏ Header Mount
Overhead Bracket Mount
❏ 12'' ❏ 18'' ❏ 24''– Projection –
Opens to:
❏ One Side
❏ Bi-Parting
800•888•9750
5350 Campbells Run Road • Pittsburgh, PA 15205-9738 • 412.787.9750 Fax: 412.787.3665 • Web Site: www.tmi-pvc.com • E-Mail: [email protected]
OTHER TMI PRODUCTS
MEGA-PRO™SWINGING DOORS
BULK PVCFILM • STRIP • SHEET • PANEL
SCREENS, CURTAINSand ENCLOSURES
DOCK ACCESSORIES
STRIP DOORS
AIR DOORS
Copyright © 2007 TMI, LLC Catalog No. II-TMIASD 06-07
INSTALLATION INSTRUCTIONS