INSTALLATION

CUSTOMER SERVICE 877.370.3604 (toll free)

INSTALLATION QUESTIONS

techsupport@kuryakyn.com or call 715.247.2983

LIMITED WARRANTY

Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in

materials and workmanship for a period of one (1) year from the date of purchase by the

consumer excepting the following provisions:

● Küryakyn shall have no obligation in the event the customer is unable to provide a receipt

showing the date the customer purchased the product(s).

●The product must be properly installed,

maintained and operated under normal conditions.

●Küryakyn makes no warranty, expressed or

implied, with respect to any gold plated products.

●Küryakyn shall not be liable for any

consequential and incidental damages, including labor and paint, resulting from failure of a

Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or

for any breech of contract or duty between Küryakyn and a customer.

●Küryakyn products are often intended for use in

specific applications. Küryakyn makes no warranty if a Küryakyn product is used in

applications other than intended.

●Küryakyn electrical products are warranted for one (1) year from the date of purchase by the

consumer. L.E.D.’S contained in components of Küryakyn products will be warranted for defects in materials and workmanship for 3 years from

the date of purchase where as all other components shall be warranted for one(1) year.

This includes, but is not limited to; control modules, wiring, chrome & other components.

●Küryakyn makes no warranty of any kind in

regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on

all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies

with the manufacturer.

ABOUT OUR CATALOG For purchasing Küryakyn® products, you

can receive a complete catalog free of charge. Send the Proof-of-Purchase below with

your address to: Küryakyn, P.O. Box 339, Somerset, WI 54025.

Please indicate either Accessories Catalog for Harley-Davidson® or GL & Metric Cruisers.

Be sure to ask your local dealer about other

Küryakyn® products, the motorcycle parts and accessories designed for riders by riders.

©2005 Küryakyn USA® All Rights reserved.

PARTS INCLUDED 2 Offset/Clevis Assemblies 1 Right Plate 1 Left Plate 2 Thick Spacers 4 Thin Spacers 1 Hardware Kit Including: 4 M6 x 1.0 x 25mm Button Socket Cap Screws (BSCS) 2 M6 x 1.0 x 30mm Button Socket Cap Screws (BSCS) 2 M6 Nylon Insert Locknuts 8 1/4” Flat Washers 4 1/4” Split Lock Washers 2 5/16”-18 x 3/4” Socket Head Cap Screws (SHCS) 4 Self-Tapping Screws 2 Anti-Seize Packets 2 3/8” Hot Spots 2 5/16” Hot Spots 1 Installation Instructions Please read and understand entire instructions before starting installation.

THANK YOU FOR CHOOSING KϋRYAKYN! IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT. WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY. ATTENTION! This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality. CAUTION! This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage. TOOLS SUGGESTED Set of Hex Wrenches, Combination Wrenches, Pliers, Power Drill, Drill bits STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS. STEP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the ignition. WARNING! YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION. ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY.

ADJUSTABLE CRUISE PEG MOUNTS 4579

4579-24MC-0811 -cont.-

PAGE

2

ATTENTION! Be sure to use the supplied anti-seize on all threaded fasteners

before installation. This will reduce galling and make future removal of the fasteners easier.

ATTENTION! This procedure requires making permanent modifications to the floorboard; this may void your warranty. Consult your dealer for more information. STEP 2 Remove the floorboard pads from both boards by gently pulling up on the rubber pad, and simultaneously pushing on the rubber darts protruding from the underside of the floorboard assembly as shown in PIC 1. STEP 3 Remove the left and right floorboard assemblies from the bike by removing the e-clip, pin and spring as shown in PIC 2; this hardware will be used again. For Vulcan 1700 and Voyager models: Label the left and right side (sitting on bike) boards. STEP 4 and STEP 5 For Vulcan 1700 and Voyager Models Only—All others proceed to STEP 6 STEP 4 Remove the wear pads from the floorboard bases by removing the two screws securing them in place. NOTE: The left floorboard base will be used on the right side of the bike, the right side floorboard base will be used on the left side. STEP 5 Locate the two un-used stand-offs (PIC 3) located on the underside of the floorboard. Clamp the wear pad in place over these stand-offs lining up the holes and drill using a 13/64 drill bit and secure the wear pad (removed in Step 4) in this location using the included self-tapping screws. Repeat for the other board. STEP 6 Remove the adhesive backing from two thin spacers and one thick spacer; install the spacers on the right plate as shown in PIC 4. STEP 7 Install the right plate on the bottom side of the floorboard, securing with two M6 x 1.0 x 25mm BSCS screws, 1/4” lock washers and 1/4” flat washers as shown in PIC 5 STEP 8 Place the floorboard assembly on a workbench and drill a hole through the footboard assembly from the bottom, using a 1/4” drill bit in the third hole. PIC 5 STEP 9 From the top of the floorboard, place a M6 x 1.0 x 30mm BSCS screw, and 1/4” flat washer through the hole that was just drilled and secure from the underside using a 1/4” flat washer and M6 nylon-locking nut. PIC 6

ADJUSTABLE CRUISE PEG MOUNTS INSTALLATION

-cont.-

PIC 1

PIC 2

PIC 3

PIC 4

PUSH THESE RUBBER DARTS THROUGH

E-CLIP

PIN

SPRING

THICK SPACERS

LEFT RIGHT

THIN SPACERS

CLAMP WEAR PAD AND DRILL HERE

PAGE

3

STEP 10 Reinstall the floorboard on the motorcycle using the pin, spring and e-clip that were removed in STEP 3. STEP 11 Install the offset on the splined shaft of the mount plate and secure with the 5/16”-18 x 3/4” SHCS screw. STEP 12 Reinstall the floorboard rubber pad removed in STEP 2. STEP 13 Repeat STEP 6 through STEP 12 for the left side.

STEP 14 Loosen and rotate the clevis clamps to the desired position.

NOTE: Position the clevis so the peg mount stop is on the topside as shown in PIC 7. You may need to remove the clevis and switch them to the other side. STEP 15 Install the foot pegs (sold separately) into the clevis; sit on the bike and adjust the arms and clevis to their desired position and tighten the screws. STEP 16 Install the 5/16” hot spots in the head of the screws that secures the arms to the mounts and the 3/8” hot spots in the head of the screws that secure the pegs to the clevis. PIC 8 WARNING! THE INSTALLATION OF AFTERMARKET PEGS MAY AFFECT GROUND CLEARANCE WHEN CORNERING.

CAUTION! Ensure that the installation of this product does not interfere with the proper operation of the motorcycle before riding. ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners (including pre-assembled) are tightened before operation of the motorcycle. Küryakyn will not warranty components lost due to improper installation. Periodic maintenance may be required.

Ride On!

ADJUSTABLE CRUISE PEG MOUNTS INSTALLATION

PIC 5

PIC 6

PIC 7

PIC 8

DRILL 1/4” HOLE STEP 8

M6 X 1.0 X 30MM BSCS AND WASHERS

BOTTOM SIDE OF BOARD

M6 X 1.0 X 30MM BSCS AND WASHER FROM TOP SIDE IN DRILLED HOLE

MAKE SURE THE TALL LIP IS IN THE UP POSITION. IT PREVENTS THE PEG FROM INTERFERING WITH THE BRAKE AND SHIFT LEVER WHEN FOLDED UP

INSERT 5/16”HOT SPOT HERE

INSERT 3/8” HOT SPOT HERE