Advanced Course of Aerospace Guidance and Control

Homework June 9, 2016

Student No. 15350940 Name: Pham Kim Cuong

Subject 1: Design the bank control law by root locus method and make numerial simulation

using the lateral/directional linearized equations of motion for the flight condition 3 of

Boeing 747.

Answer:

Use the MATLAB code as shown in appendix we have the Boeing 747 model during flight

condition 3 is:

A=[−0.12 0 −1 0.04−4.12 −0.98 0.29 01.62 −0.016 −0.232 0

0 1 0 0 ]B=[ 0 0

0.31 0.180.013 −0.92

0 0 ]A=[0 0 57.2958 0

0 0 0 57.2958]

B=[0 00 0 ]

The following commands specify this state-space model as an LTI object and attach names to

the states, inputs, and outputs:sys = ss(A,B,C,D);

set(sys, 'inputname', {'aileron' 'rudder'},...

'outputname', {'yaw rate' 'bank angle'},...

'statename', {'beta' 'roll' 'yaw' 'phi'});

We can display the LTI model system by typing sys in MATLAB command line. MATLAB

responds with:

The model has two inputs and two outputs. The units are radians for beta (sideslip angle) and

phi (bank angle) and radians/sec for yaw (yaw rate) and roll (roll rate). The rudder and

aileron deflections are in radians as well.

Compute the open-loop eigenvalues and plot them in the s-plane.

This model has one pair of lightly damped poles. They correspond to what is called the

“Dutch roll mode.”

Open-Loop Analysis

First perform some open-loop analysis to determine possible control strategies. Start with the

time response. Use impulse(sys) in MATLAB command line:

The impulse response confirms that the system is lightly damped. But the time frame is much

too long because the passengers and the pilot are more concerned about the behavior during

the first few seconds rather than the first few minutes. Next look at the response over a

smaller time frame of 40 seconds. Enter impulse(sys,40) command in MATLAB:

Look at the plot from aileron (input 1) to bank angle (output 2). The aircraft is oscillating

around a nonzero bank angle. Thus, the aircraft is turning in response to an aileron impulse.

The control from rudder has significant effect around the lightly damped Dutch roll mode.

To make the design easier, we will design feedback control for controlling from rudder to

yaw rate.

System12: control from rudder to yaw rate.

Root Locus Design:

Plot the root locus for the system12:

This is the root locus for negative feedback and shows that the system goes unstable almost

immediately. If, instead, we use positive feedback, we may be able to keep the system stable.

This looks better. Just using simple feedback, we can achieve a damping ratio of 0.7. Let

chose K=0.03. Plot the closed-loop impulse response for a duration of 20 seconds, and

compare it to the open-loop impulse response.

The closed-loop response settles quickly and does not oscillate much, particularly when

compared to the open-loop response. Now close the loop on the full MIMO model and see

how the response from the aileron looks.

The yaw rate response is now well damped. We can achieve damping of 0.7 and the stability

time is about 25s.

APPENDIX

%Create state space model of Boeing 474 in condition 3clc;clear all;g = 10;U0 = 250;q0 = 244420alpha0 = 0;gamma0 = 0;theta0 = (alpha0+gamma0)/180*pi();W0 = U0*alpha0; Yv = -0.12;Ydr = 0.014;L_b = -4.12;L_p = -0.98;L_r = 0.29;L_da = 0.31;L_dr = 0.18;N_b = 1.62;N_p = -0.016;N_r = -0.232;N_da = 0.013;N_dr = -0.92; Yb = U0*Yv; A = [Yb/U0 W0/U0 -1 g*cos(theta0)/U0; L_b L_p L_r 0; N_b N_p N_r 0; 0 1 tan(theta0) 0];B = [0 0; L_da L_dr; N_da N_dr; 0 0];C=[0 0 57.3 0; 0 0 0 57.3];D=[0 0; 0 0];sys = ss(A,B,C,D);set(sys, 'inputname', {'aileron' 'rudder'},... 'outputname', {'yaw rate' 'bank angle'},... 'statename', {'beta' 'roll' 'yaw' 'phi'});

Subject 2:

Survey the anomalies of satellite HITOMI and make consideration what should be done for

the next chance not to cause the accident from the point of engineering view.

Answer:

The anomalies of HITOMI:

1) On March 26th, attitude maneuver to orient toward an active galactic nucleus was

completed as planned.

2) After the maneuver, unexpected behavior of the ACS (Attitude Control System)

caused incorrect determination of its attitude as rotating, although the satellite was not

rotating actually. In the result, the Reaction Wheel (RW) to stop the rotation was

activated and lead to the rotation of satellite.

3) In addition, unloading (Unloading:Operation to decrease the momentum kept in RW

within the range of designed range) of angular velocity by Magnetic Torquer operated

by ACS did not work properly because of the attitude anomaly. The angular

momentum kept accumulating in RW.

4) Judging the satellite is in the critical situation, ACS switched to SH (Safe Hold) mode,

and the thrusters were used. At this time ACS provided atypical command to the

thrusters by the inappropriate thruster control parameters. As a result, it thrusted in an

unexpected manner, and it is estimated that the satellite rotation was accelerated.

5) Since the rotation speed of the satellite exceeded the designed speed, the satellites

parts that are vulnerable to the rotation such as SAP (Solar Array Paddles), EOB

(Extensible Optical Bench) and others separated off from the satellite.

The reasons cause anomalies:

In satellites, the STT typically gets a good fix and sends the data to the IRU. The IRU

uses the data to set its current reading and to measure how far it drifted since the last update.

After calculating the drift it uses drift adjustments to compensate for the future drift. Clearly

if the compensation calculation is wrong the future readings are going to be wrong. This

appears to have played a role since the ACS attempted to correct a rotation that didn’t exist.

The erroneous configuration information led the ACS to aggravate, not correct, the rotation.