AGC01039140302 Page 1 of 43 RF Test Report Test Report.pdfPage 1 of 43 RF Test Report ... Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive

Report No. AGC01039140302EE02

Page 1 of 43

RF Test Report

Report No.: AGC01039140302EE02

TEST NAME : 1999/5/EC R&TTE Directive Art.3.2

PRODUCT DESIGNATION

: Mobile radio

BRAND NAME : TYT

MODEL NAME : TH‐9800, TH‐9800D, TH‐7800,TH‐7900

CLIENT : TYT ELECTRONICS CO., LTD

DATE OF ISSUE : Apr. 18, 2014

STANDARD(S) : ETSI EN 301 783‐1 V1.2.1 2010‐07 ETSI EN 301 783‐2 V1.2.1 2010‐07

Attestation of Global Compliance (Shenzhen) Co., Ltd.

CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.


Page 2 of 43 REPORT REVISE RECORD

Report Version Revise Time Issued Date Valid Version Notes

V1.0 / Apr.18, 2014 Valid Original Report


Page 3 of 43TABLE OF CONTENTS

1. TEST RESULT CERTIFICATION ............................................................................................................................................ 4

2 EUT DESCRIPTION ......................................................................................................................................................................... 5

3 TEST METHODOLOGY .................................................................................................................................................................. 6

3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS .................................................................................................... 6 3.2 DESCRIPTION OF TEST MODES ......................................................................................................................................... 6

4 FACILITIES AND ACCREDITATIONS ...................................................................................................................................... 6

4.1 FACILITIES ................................................................................................................................................................................ 6

5 SETUP OF EQUIPMENT UNDER TEST ................................................................................................................................... 6

5.1 SETUP CONFIGURATION OF EUT ...................................................................................................................................... 6 5.2 SUPPORT EQUIPMENT .......................................................................................................................................................... 6

6. CONFORMANCE REQUIREMENT .............................................................................................................................................. 6

6.1 MAXIMUM POWER (PX) (CONDUCTED) .................................................................................................................. 7 6.2 CONDUCTED SPURIOUS EMISSION IN TRANSIMIT MODE .................................................................................. 9 6.3 CONDUCTED SPURIOUS EMISSION IN RECEIVE OR TRANSIMIT STANDBY MODE ....................................... 17 6.4 RADIATED SPURIOUS EMISSION.......................................................................................................................... 20 6.5 RADIATED SPURIOUS EMISSION.......................................................................................................................... 27 6.6 CONDUCTED RF IMMUNITY ................................................................................................................................... 32

APPENDIX 1 ....................................................................................................................................................................................... 35

PHOTOGRAPHS OF TEST SETUP ............................................................................................................................................... 35

APPENDIX 2 ....................................................................................................................................................................................... 36

PHOTOGRAPHS OF EUT ................................................................................................................................................................ 36


Page 4 of 43

1. TEST RESULT CERTIFICATION

APPLICABLE STANDARD

STANDARD TEST RESULT

ETSI EN 301 783-1V1.2.1:2010-07 ETSI EN 301 783-2V1.2.1:2010-07 Complied

The above equipment was tested by Attestation of Global Compliance Co., Ltd. for compliance with the requirements set forth in the European Standard ETSI EN 301 783-1/-2 The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties.

Tested by

Bart Xie Apr. 18, 2014

Checked By

Kidd Yang Apr. 18, 2014

Authorized By

Solger Zhang Apr. 18, 2014

Applicant: TYT ELECTRONICS CO., LTD Block 39-1, Optoelectronics-information industry base, Nan’an, quanzhou, Fujian

Manufacturer: TYT ELECTRONICS CO., LTD Block 39-1, Optoelectronics-information industry base, Nan’an, quanzhou, Fujian

Product Designation : Mobile radio

Brand Name: TYT

Model Name: TH-9800

Series Model: TH-9800D, TH-7800,TH-7900

Model Difference: All the same except for model name.

Date of Test: Apr.10, 2014 to Apr. 17, 2014


Page 5 of 43

2 EUT DESCRIPTION

Product: Mobile radio

Brand Name: TYT

Model Name: TH-9800

Hardware Version: N/A

Software Version: N/A

Operation frequency: 28.000MHz- 29.700MHz,50MHz-52MHz, 144MHz-146MHz,430MHz-440MHz

Modulation: FM

Operation mode: Push to Talk

Channel Seperation 12.5KHz, 25 KHz

Rated Output Power 28-29.7MHz/50-52MHz/144-146MHz:50W 430-440MHz:40W

Power Supply DC12V by lead-acid battery or 13.8V DC source

Note: For more details, please refer the user’s manual

Test mode: 1, transmitting in FM modulation. Test channel: Low channel: 28.000MHz Middle channel: 28.900MHz High channel: 29.700MHz Low channel: 50.000MHz Middle channel: 51.000MHz High channel: 52.000MHz Low channel: 144.000MHz Middle channel: 145.000MHz High channel: 146.000MHz Low channel: 430.000MHz Middle channel: 435.000MHz High channel: 440.000MHz


Page 6 of 43 3 TEST METHODOLOGY 3.1 GENERAL DESCRIPTION OF APPLIED STANDARDS According to its specifications, the EUT must comply with the requirements of the following standards: ETSI EN 301 783-1 2010-07: Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Commercially available amateur radio equipment; Part 1: Technical characteristics and methods of measurement ETSI EN 301 783-2 2010-07: Electromagnetic compatibility and Radio spectrum Matters (ERM);Land Mobile Service; Commercially available amateur radio equipment; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive 3.2 DESCRIPTION OF TEST MODES The EUT has been tested under typical operating condition. No software used to control the EUT for staying in transmitting and receiving mode for testing. 4 . FACILITIES AND ACCREDITATIONS 4.1 FACILITIES Attestation of Global Compliance (Shenzhen) Co., Ltd. 2/F., Building 2, No.1-No.4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang, Bao'an District, Shenzhen, Guangdong, China 5 SETUP OF EQUIPMENT UNDER TEST 5.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 5.2 SUPPORT EQUIPMENT No available support equipment during the testing. Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 5.3 Measurement uncertainty： Radio frequency: 1×10-7

RF Power(up to 160W): ±0.5dB Radiated RF power: ±4dB Conducted spurious emission of transmitter valid up to 12.75 GHz: ±2.75dB Conducted spurious emission of receiver, valid up to 12.75 GHz: ±4.2dB Two-signal measurement, valid up to 4 GHz: ±2dB Radiated emission of the transmitter, valid up to 4GHz: ±3dB Radiated emission of the receiver, valid up to 4 GHz: ±3dB 6. CONFORMANCE REQUIREMENT


Page 7 of 436.1 MAXIMUM POWER (PX) (CONDUCTED)

TEST CONFIGURATION

Note: The impedance of attenuator is 50ohm. TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1 (V.1.4.1) Sub-clause 4.2 for the test conditions. 2. Please refer to ETSI EN 301 783-1 (V1.2.1) Sub-clause 5.1.2 for the measurement method. Test result:

12.5 KHz Channel Separation

Operation frequency Channel Output power

28MHz-29.7MHz Low 46.75

Middle 46.56 high 46.77

50MHz-52MHz Low 46.55


144MHz-146MHz Low 46.43


430MHz-440MHz Low 45.58


SG


Page 8 of 4325 KHz Channel Separation

Operation frequency Channel Output power

28MHz-29.7MHz Low 46.83




144MHz-146MHz Low 46.82


430MHz-440MHz Low 45.37



Page 9 of 436.2 CONDUCTED SPURIOUS EMISSION IN TRANSIMIT MODE LIMIT EN 301 783-1 [1], clause 5.2.3, table 4:

The rated output power is 50W, -(43+10*log(PEP))= -60 dBc, refer to table 4, the limit for VHF should be:

-50dBc (-3dBm) below 30MHz, and -60dBc (-13dBm) above 30MHz.

The rated output power is 40W, -(43+10*log(PEP))= -59 dBc, refer to table 4, the limit for UHF should be:


MEASUREMENT EQUIPMENT USED

Equipment Name Manufacture Model No. Dul.Date

spectrum analyzer Agilent E4440A 2014-07-17

H&T Chamber EXPERY TN-400 2014-07-17

Signal generator Aglient E4421B 2014-07-17 Remark: Each piece of equipment is scheduled for calibration once a year.


Page 10 of 43TEST CONFIGURATION

Note: The impedance of attenuator is 50ohm. TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V1.2.1) Sub-clause 5.2.2.1 for the measurement method. TEST RESULTS Note: 1.the EUT have been tested under DC 13.2V AND DC 13.8V, only result the worst case(DC 13.8V) in this part 2.only result the worst channel for each moudulation

SG


Page 11 of 43TEST RESULT OF12.5KHZ CHANNEL SEPARATION

(28-29.7MHz) Low channel, 150KHz-30MHz

Low channel, 30MHz – 1GHz


Page 12 of 43Low channel, 1GHz – 4GHz

TEST RESULT OF12.5KHZ CHANNEL SEPARATION FM Modulation (50-52MHz)

Low channel, 150KHz-30MHz


Page 13 of 43Low channel, 30MHz – 1GHz

Low channel, 1GHz – 4GHz


Page 14 of 43TEST RESULT OF12.5KHZ CHANNEL SEPARATION

FM Modulation (144-146MHz) High channel, 150KHz-30MHz

High channel, 30MHz – 1GHz


Page 15 of 43High channel, 1GHz – 4GHz

TEST RESULT OF12.5KHZ CHANNEL SEPARATION

FM Modulation (430-440MHz) High channel, 150KHz-30MHz


Page 16 of 43High channel, 30MHz – 1GHz

High channel, 1GHz – 5GHz


Page 17 of 43 6.3 CONDUCTED SPURIOUS EMISSION IN RECEIVE OR TRANSIMIT STANDBY MODE LIMIT EN 301 783-1 [1], clause 5.2.3,table 5:


Equipment Name Manufacture Model No. Dul.Date

spectrum analyzer Agilent E4440A 2014-07-17

H&T Chamber EXPERY TN-400 2014-07-17

Signal generator Agilent E4421B 2014-07-17 Remark: Each piece of equipment is scheduled for calibration once a year. TEST CONFIGURATION

SG


Page 18 of 43TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V1.2.1) Sub-clause 5.2.2.1 for the measurement method. TEST RESULTS

TEST RESULT OF 12.5KHZ CHANNEL SEPARATION FM Modulation (430MHz-440MHz)

150KHz-30MHz


Page 19 of 4330MHZ-1GHz

1GHz-12.75GHz

Note: 1.the EUT have been tested under DC 13.2V AND DC 13.8V,

only result the worst case(DC 13.8V) in this part 2.only result the worst case(FM moudulation 430MHz-440MHz) in this part.


Page 20 of 43

6.4 RADIATED SPURIOUS EMISSION -ENCLOSURE PORT IN TRANSMIT MODE LIMIT EN 301 783-1 [1], clause 5.2.3, table6:

For VHF the rated output power is 50W, -(43+10*log(PEP))= -60 dBc, refer to table 4, the limit for VHF should be:


For UHF the rated output power is 40W, -(43+10*log(PEP))= -59 dBc, refer to table 4, the limit for UHF should be:



Equipment Name Manufacture Model No. SERIAL NUMBER Dul.Date

Spectrum Analyzer Agilent E4440A N/A 2014-07-17

Amplifier EM EM30180 0607030 2014-07-17

Horn Antenna EM EM-AH-10180 N/A 2014-07-17

Horn Antenna A.H. Systems Inc. SAS-574 -- 2014-07-17 EMI Test Receiver Rohde & Schwarz ESCI N/A 2014-07-17

Amplifier EM EM30180 N/A 2014-07-17

Bilogical Antenna A.H. Systems Inc. SAS-521-4 N/A 2014-07-17

Loop Antenna A.H. SAS-562B SEL0097 2014-07-17

Isolation Transformer LETEAC LTBK -- 2014-07-17


Page 21 of 43TEST CONFIGURATION Below 1GHz


Page 22 of 43Above 1GHz

TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V 1.2.1) Sub-clause 5.2.2.2 for the measurement method. Test result Note: 1. the fundamental wave has been filtered by trap filter.

2. the EUT have been tested under DC 13.2V AND DC 13.8V, only result the worst case(DC 13.8V) in this part

3. No emission found below 30MHz, only result the worst case (FM modulation 144-146MHz) in this part.


Page 23 of 43TEST RESULT OF 12.5 KHZ CHANNEL SEPARATION

EUT: TH-9800 Voltage: DC 13.8V

Test Mode: FM Modulation transmitting in High Channel Temperature: 25°C

Polarity: Horizontal Atmosphere Pressure 101.2Kpa

No. Freq.(MHZ) Reading

(dBuV) Substitution Power(dBm)

Factor(dB)

Measurement Power(dBm)

Limit (dBm)

Margin

1 38.0833 10.46 -55.12 -10.23 -65.35 -57 -8.35

2 112.4500 8.76 -54.26 -6.45 -60.71 -57 -3.71

Note: Measurement Power= Substitution Power + Factor Margin=Measurement Power - Limit


Page 24 of 43



Polarity: Vertical Atmosphere Pressure 101.2Kpa



Factor(dB)


Limit (dBm)

Margin

1 34.8500 11.32 -56.79 -10.23 -67.02 -57 -10.02

2 88.2000 8.41 -53.24 -6.45 -59.69 -57 -2.69



Page 25 of 43



Polarity: Horizontal Atmosphere Pressure 101.2Kpa



Factor(dB)


Limit (dBm)

Margin

1 2683.333 25.06 -47.16 -4.97 -52.13 -13 -39.13

2 3725.000 26.47 -45.12 -5.34 -50.46 -13 -37.46



Page 26 of 43



Polarity: Vertical Atmosphere Pressure 101.2Kpa

No. Freq.(MHZ) Reading (dBuV)

Substitution Power(dBm)

Factor(dB)


Limit (dBm)

Margin

1 1600.000 39.41 -35.75 -5.45 -41.2 -13 -28.2

2 1870.000 32.88 -41.26 -7.12 -48.38 -13 -35.38



Page 27 of 436.5 RADIATED SPURIOUS EMISSION -ENCLOSURE PORT IN RECEIVE OR STANDBY MODE LIMIT EN 301 783-1 [1], clause 5.2.3,table7:

MEASUREMENT EQUIPMENT USED The same with mesasurement equipment used of section 6.3 TEST CONFIGURATION The same with test configuration of section 6.3 TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V 1.2.1) Sub-clause 5.2.2.2 for the measurement method. TEST RESULTS Note: 1. the EUT have been tested under DC 13.2V AND DC 13.8V,

only result the worst case(DC 13.8V) in this part. 2. only result the worst case(FM moudulation 144-146MHz) in the part.


Page 28 of 43TEST RESULT OF 12.5KHZ CHANNEL SEPARATION

Below 1G

EUT: TH-9800 Voltage: DC 13.8V Test Mode: FM Modulation in idle mode Temperature: 25°C Polarity: Horizontal Atmosphere Pressure 101.2Kpa



Factor(dB)


Limit (dBm)

Margin

1 38.0833 11.75 -55.12 -10.23 -65.35 -57 -8.35

2 76.8833 6.41 -54.26 -6.45 -60.71 -57 -3.71


Page 29 of 43

EUT: TH-9800 Voltage: DC 13.8V Test Mode: FM Modulation in idle mode Temperature: 25°C Polarity: Vertical Atmosphere Pressure 101.2Kpa



Factor(dB)


Limit (dBm)

Margin

1 31.6167 7.48 -56.79 -10.23 -67.02 -57 -10.02

2 88.2000 2.64 -53.24 -6.45 -59.69 -57 -2.69


Page 30 of 43Above 1G

EUT: TH-9800 Voltage: DC 13.8V Test Mode: FM Modulation in idle mode Temperature: 25°C Polarity: Horizontal Atmosphere Pressure 101.2Kpa



Factor(dB)


Limit (dBm)

Margin

1 1870.000 29.88 -44.36 -7.65 -52.01 -47 -5.01

2 2880.000 31.39 -47.86 -5.98 -53.84 -47 -6.84


Page 31 of 43

EUT: TH-9800 Voltage: DC 13.8V Test Mode: FM Modulation in idle mode Temperature: 25°C Polarity: Vertical Atmosphere Pressure 101.2Kpa

No. Freq.(MHZ) Reading (dBuV)

Substitution Power(dBm)

Factor(dB)


Limit (dBm)

Margin

1 1600.000 29.11 -42.69 -8.65 -51.34 -47 -4.34

2 2470.000 30.55 -49.15 -6.18 -55.33 -47 -8.33


Page 32 of 43 6.6 CONDUCTED RF IMMUNITY LIMIT REFER TO 301 783-1 SUBPART 5.3.3 Application of the test signal shall not cause the demodulated receiver output to:

• be reduced to less than 12 dB SINAD for analogue speech equipment; or • be reduced to less than 80 % of the original data throughput for non-speech equipment; or • be degraded to a level declared by the manufacturer as appropriate for the type of signal conveyed. MEASUREMENT EQUIPMENT USED Name of Equipment Manufacturer Model Serial Number Calibration Due

Communication Test Set HP HP8920B US35010135 2014-07-17

Signal Generator Agilent E4421B 100059 2014-07-17

Signal Generator R&S SMT02 A0304261 2014-07-17 TEST CONFIGURATION

TEST PROCEDURE 1. Please refer to ETSI EN 301 783-1(V1.2.1), clause 4.2 for test condition. 2. Please refer to ETSI EN 301 783-1 (V 1.2.1) Sub-clause 5.3.2.1 for the measurement method. Singnal of signal generator 1:

Signal Generator 1

Communication Tester

Combination Network

(EUT)

Signal Generator 2


Page 33 of 43Singnal of signal generator 2:

TEST RESULTS

RESULT OF DC 13.2V POWER Frequency Operation frequency Channel SINAD

Below 30MHz

28MHz-29.7MHz

Low 18.75 Middle 17.97 High 16.48


Middle 14.45 High 14.96

144MHz-146MHz Low 14.38


430MHz-440MHz Low 14.75


30MHz to 1GHz

28MHz-29.7MHz

Low 17.28 Middle 18.97 High 18.55



144MHz-146MHz Low 14.37


430MHz-440MHz Low 14.77


RESULT OF DC 13.8V POWER Frequency Operation frequency Channel SINAD


Page 34 of 43

Below 30MHz

28MHz-29.7MHz

Low 18.46 Middle 17.86 High 17.26



144MHz-146MHz Low 14.63


430MHz-440MHz Low 14.56


30MHz to 1GHz

28MHz-29.7MHz

Low 16.75 Middle 16.75 High 16.46



144MHz-146MHz Low 14.65


430MHz-440MHz Low 14.25



Page 35 of 43APPENDIX 1

PHOTOGRAPHS OF TEST SETUP RADIATED SPURIOUS EMISSION TEST SETUP

CONDUCTED SPURIOUS EMISSION TEST SETUP


Page 36 of 43APPENDIX 2 PHOTOGRAPHS OF EUT

WHOLE VIEW OF EUT

TOP VIEW OF EUT


Page 37 of 43BOTTOM VIEW OF EUT

FRONT VIEW OF EUT


Page 38 of 43BACK VIEW OF EUT

LEFT VIEW OF EUT


Page 39 of 43RIGHT VIEW OF EUT

OPEN VIEW OF EUT


Page 40 of 43INTERNAL VIEW-1 OF EUT

INTERNAL VIEW-2 OF EUT





Page 42 of 43






---END OF REPORT---

Documents

AGC01039140302 Page 1 of 43 RF Test Report Test Report.pdfPage 1 of 43 RF Test Report ... Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive