®

Agriair 2200PG & Agriair 2200PG-230Operation and Maintenance Manual

WARNINGDo not use with combustible or explosive material. Do not expose to water or rain. Connect only to grounded outlet with GFCI device. Disconnect power for cleaning and servicing. This equipment to be operated only by trained personnel. High intensity Ultraviolet light. Avoid eye and skin exposure.Do not operate without coverings. Do not look directly at UV light source. Wear UV eye protection.

Safety Warning Instructions:READ AND SAVE THESE INSTRUCTIONS

This equipment to be operated only by trained personnel.

Do not use with combustible or explosive material.

Do not expose to water or rain.

Connect only to grounded outlet with GFCI device.

Disconnect power for cleaning and servicing.

Do not operate if cord or plug is damaged. Contact a authorized service facility for examination and/or repair.

Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away

from traffic areas and where it is not a tripping hazard.

Disconnect power for cleaning and servicing.

High intensity Ultraviolet light inside. Avoid eye and skin exposure.

Do not look directly at UV light source. Wear UV eye protection.

Do not operate without coverings.

Avertissement de sécurité Instructions:LIRE ET CONSERVER CES INSTRUCTIONS

Cet équipement doit être utilisé que par un personnel formé.

Ne pas utiliser avec des matières combustibles ou explosives.

Ne pas exposer à l’eau ou à la pluie.

Connectez uniquement à une prise mise à la terre avec un dispositif GFCI.

Coupez l’alimentation électrique pour le nettoyage et l’entretien.

Ne pas utiliser si le cordon ou la fiche est endommagé. Contactez un centre de service autorisé pour examen et / ou

réparation.

Ne pas passer le cordon sous un tapis. Ne pas couvrir le cordon avec des carpettes, les coureurs, ou revêtements simi-

laires. Éloigner le cordon des endroits passants et où il n’est pas un risque de déclenchement.

Coupez l’alimentation électrique pour le nettoyage et l’entretien.

Haute intensité de lumière ultraviolette à l’intérieur. Évitez les yeux et l’exposition de la peau.

Ne pas regarder directement à la source de lumière UV. Porter des lunettes de protection UV.

Ne pas faire fonctionner sans revêtement.

The AgriAir 2200PG air purifier generates friendly oxidizer plasma which seeks and destroys odors and bio-contaminants at their source, in indoor commercial cultivation facilities. Our energy efficient purifier produces and distributes oxidizer plasma naturally generated from humidity and oxygen in the surrounding area. The 2200PG is sized to sanitize environments 3,000-8,000 cubic feet of flowering, drying and packaging rooms, without the use of chemicals or ozone. It’s portable, easy to install, scalable and ready to plug-in and go.

Agriair 2200PGAirflow: 300 – 1600 CFM Variable speed blower. Note: *Airflows based on blower manufacturer curves. Different HEPA filters may cause the flow to varyPower Requirements: 115 VAC/60 Hz/11.6 ampsPCO Generators: (2) 14” Photo-Catalytic Generators Filtration: 24” x 24” x 12” HEPA Filter 99.99%, 0.3μ, 24” x 24” x 1.5”MERV 8 prefilterRecessed Controls: High/OFF/Speed Control Switch, Variable Speed Controller, Filter Change Light, Generator On/Off Switches, Running Hour MetersMotor: 1 HP w/Thermal OverloadHousing: Aluminum and Steel with Epoxy Paint, 5” Casters, Rubber Grip Handles

Exhaust Collar: 12 ” DiameterSize/Weight with Filters: 34”L x 26”W x 31”H, 140 lbs

Receiving InstructionsVisually inspect the unit for damage. Ensure that the filters have not been dislodged during shipping. The unit must be operated with filters in place.

Operation of the Agriair 2200PGThe AgriAir 2200 PG is used to purify the air in highly sensitive environments at risk of bio-contamination such as cannabis drying, trimming and packaging areas. It provides HEPA filtration and PCO technology to distribute enough oxidizer plasma to maintain a high level of air sanitation and odor control in and odor control in 6,000-20,000 cubic feet of space. The oxidizer plasma provides bio-protection 24/7 without the use of chemicals. This unit is portable, easy to install and scalable to any size operation.

Operating Instructions1) Turn the blower on by selecting a setting on the fan power switch; ON (high), FAN, Speed Controller (low). 1a) Select the preferred airflow level, using the speed control knob.3) To turn on generator(s), switch the generator switch(es) to the ON position. 4) The orange LED turns on when the HEPA filter needs to be changed.

Prefilter Replacement1. Unplug the unit and remove the filter protection gate.2. Remove the used filter and install new one.3. Slide the gate in the track.

Generator Cell ReplacementThe generator cell’s output slowly degrades and should be replaced after 25,000 hours of running. 1) Unplug the machine.2) Remove the filters: primary/secondary filter & HEPA filter.3) Remove the first generator by unplugging, then remove the (4) screws holding it in place. (Once the first generator is removed, you will have access to the second generator.)

Ordering Info Part # AgriAir 2200PG AA2200PG

HEPA Filter 99.99%, 0.3μ (metal frame) OAH2424G

Vapor Trap V-bank Filter OCVT2424

OdorGuard 600 Carbon Filter OG2424D

ABS Plastic Intake Manifold, 12” Dia. OAIM2200-12

Quick Clamp, 12”-16” Dia. QCW14

Flexible Duct, 12” Dia. x 25’ L OAD12

Flexible Duct, Wire & Fiber Reinforced OAD12R

Flexible Duct, Wire & Fiber Reinforced, 12” Dia. x 25’ L OAD12D

Agriair 14” Replacement Generator Cell EHPG-4

4640 Campus Place, Suite 100T. 425.290.3922 | F. 425.290.3964

Wiring DiagramDRAWN BY: REV

SCALE DATE SHEET

A. Briceno A

Not to Scale Nobember 9, 2018

MODEL

Diagram Legend

Terminated (Capped) Wire

Wiring Connector

Red LED LightR

Green LED LightG

Amber LED LightA

115VAC60hz

BLUE

WHITE

BLACK

GREEN

WHITE

BLACK

GREEN

LED

R

1 HPMOTOR

SPEEDCONTROLLER

GREEN

ON/OFFSWITCH

PRESSURESWITCH

ELEMENTSWITCH

ELEMENTHOURMETER

ELEMENT

AA2200PG

1 of 1

OMNITEC DESIGN LIMITED WARRANTY

Omnitec Design warrants, for a period of twelve (12) months from the date of purchase, that all Products, component parts and accessories, excluding filters, will be free from defects in material and workmanship under normal use and service.

THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS F.O.B., Omnitec Design 4640 Campus Place Ste. 100, Mukilteo, WA 98275 Phone: 425-290-3922

In order to keep this warranty in effect for the aforementioned twelve-month period, the purchaser must (i) promptly, i.e., immediately upon discovery, inform Omnitec Design’s customer service of any defects, and (ii) properly use and maintain the Product prior to the discovery of any defect.

This warranty does not cover normal wear and tear or defects caused by (i) improper or negligent handling or unauthorized modifications; (ii) defective or improper premises, chemical, or electrical influences; or (iii) weather or other forces of nature.

In order to provide the best customer service possible, Omnitec Design requests that purchaser completes the enclosed LIMITED WARRANTY REGISTRATION FORM and returns it to Omnitec Design within 30 days of purchase date.

LIMITATIONS OF WARRANTYTHIS WARRANTY IS EXPRESSLY IN LIEU OF ANY AND ALL OTHER WARRANTIES AND OBLIGATIONS OF Omnitec Design OR ITS SUPPLIERS, EXPRESS OR IMPLIED, AND Omnitec Design EXPRESSLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

LIMITATION OF REMEDYUnder no circumstances shall Omnitec Design or any supplier of Omnitec Design be liable for any loss or damage, including, but not limited to, loss or damage arising out of the failure of the Products to operate for any period of time, inconvenience, the use of rental or replacement equipment, loss of profits or other economic loss, or general, direct, special, indirect, incidental or consequential damages or property damages.

PRODUCT SUITABILITYMany states and localities have their own varied codes and regulations governing sales, construction, installation, and/or use of Products for certain purposes. While Omnitec Design attempts to assure that its Products comply with such codes, it cannot guarantee compliance, and cannot be responsible for how the Products are installed or used. Omnitec Design recommends that, before purchasing and using a Product, purchasers review the Product application, and federal, state and local regulations, to be sure that the Products, installation, and use will comply with them.

Agriair® RETURN POLICY

Omnitec Design, the manufacturer of the Agriair® , guaranties that the equipment will function properly, to our specifications and will be repaired if necessary at no charge for a period of 1 year (See our warranty policy for details). All equipment returned to us for repairs or exchange requires an RMA number for processing and tracking.

All Agriair® & IO technology has been tested by independent labs and in several indoor grow facilities, proving the performance as described in our literature. Our air purification equipment is a powerful tool to help purify your environment yet, we cannot guaranty that under your operating conditions and procedures, the results will be the same as experienced by other growers.

If you are not satisfied with the purchase or the operation of our equipment, it can be returned under the following conditions:

If the equipment was un-used and was returned within 14 days. The customer will be charged return freight* and an additional 10% of the purchase price as a restocking fee.

Iftheequipmentwasusedandisworkingperourspecifications:Within the first 30 days of receipt, the customer will be charged return freight* and 20% of the purchase price for refurbishing. Within the first 31-60 days of receipt, the customer will be charged return freight* and 30% of the purchase price for refurbishing. Within the first 61-90 days of receipt, the customer will be charged return freight* and 40% of the purchase price for refurbishing.

After 90 days, returns will not accepted.

For returns, repairs or technical support please contact us via email at orders@agriairequipment.com or call (425) 290-3922 for further assistance.

*Please save the original packing to insure possible trouble-free returns and additional fees.

page 1

®