www.enverid.com

Air Purifier Installation Guide

enVerid Technical Documentat ion

SEPTEMBER 2020

V1.0

enverid.com

1. enVerid Air Purifier Installation View

BELOW THE CEILING (UNCONCEALED INSTALLATION) SIDE VIEW

AIR PURIFIER TOP VIEW

IN THE CEILING (CONCEALED INSTALLATION) SIDE VIEW

Floor Slab

Ceiling

Floor Slab

Air PurifierReturn Grille Supply Grille

3/8” Threaded Rod

Air PurifierDuctworkReturn Grille Supply Diffuser

Pre Filter

High Efficiency Filter

3/8” Threaded Rod

Blower UVC LampsSilencer

Floor Slab

Ceiling

Ceiling

Air PurifierDuctworkReturn Grille

Duct Clamp

Supply Diffuser

FilterAccessDoor

Control Box

Pre Filter

High Efficiency Filter

Air Muffler Box

3/8” Threaded Rod

Blower UVC LampsSilencer

3/8" Threaded Rod

Floor Slab

Ceiling

Floor Slab

Air PurifierReturn Grille Supply Grille

3/8” Threaded Rod

Air PurifierDuctworkReturn Grille Supply Diffuser

Pre Filter

High Efficiency Filter

3/8” Threaded Rod

Blower UVC LampsSilencer

enVerid Installation Guide

enverid.com

enVerid Installation Guide

2. enVerid Air Purifier Installation BOM List (not included in packaging)

NO.

1

5

11

3

9

7

13

2

6

12

4

10

8

14

IMAGENAME

Isolation Hangers

Suspension Rubber Washer

Duct Collar

Expansion Bolt

Spiral Duct

Return Air Box

485 Communication Wires

Hanging Bar

Return Air Grille

Power Line

Washer

Duct Clamp

Duct Silencer

Mccb Circuit Breaker

QTY.

4

4

3

4

2

1

Multiple

Multiple

1

Multiple

4

4

2

1

REMARK

TD-65lbs only for Purifier

3/8” Rubber Washer

8” Flexible collar

3/8” Expansion bolt NOTE: Beam clamps may be used in case where

air purifier is supported by building framing.

8” x 60” NOTE: For use in hard duct applications.

20”x20”x14” – 1” liner for sound attenuation or confirm on site

18 gauge, 2 wire, stranded and shielded wire

3/8” Threaded Rod

20”x20” minimum or to be confirmed by PM

See power requirements and local code

3/8” Fender Washer

8” Duct Clamp

8” x 40” NOTE: For use with flexible duct for sound attenuation.

MOCP 15 Amp – Do not exceed code requirements and guidelines for number of units per circuit

enverid.com

enVerid Installation Guide

3. enVerid Air Purifier Installation Method

NO.

1

5

3

7

2

6

4

8

IMAGENAME

Equipment Body

Screws

Operation and Maintenance Guide

Pre-Filter

Controller

Flange

Angle Bracket

High Efficiency Filter

QTY.

1

Multiple

1

1

1

3

4

1

REMARK

Individually packed

Included in accessories bag

Included in data packet

Included in equipment body

Individually packed

Included in equipment body NOTE: 2-Supply

1-Return

Included in accessories bag

Included in equipment body

STEP 1 Open package and check parts/documents. Assemble angle bracket (item 4) to unit (item 1) as below.

STEP 2 Install expansion bolts and threaded rod into slab. Use 3/8” expansion bolt drill depth of minimum 2”, as below.

NOTE: Minimum recommended installation height 7.5ft above the floor. Maximum recommended installation height 16ft above the floor.

Floor Slab

Air PurifierReturn Grille Arc GrilleAir Muffler Box

Expansion Bolt

2” Min. Into the SlabNuts

3/8” Threaded Rod

enverid.com

enVerid Installation Guide

STEP 3 Use four threaded rods to hang the unit, fixed with screws, and install appropriate vibration isolation devices.

The equipment location must allow access to the filter for replacement and the control board for service (A).

STEP 5 Install ductwork per local code and SMACNA guidelines. 40” minimum of hard duct silencers is suggested for flexible duct installations and 60” minimum for hard duct installations.

Both supply and return should be insulated or lined to dampen system sound.

Floor Slab

Filters Silencing Section

3/8” Threaded RodIsolation Hangers

STEP 4 Install the Air Purifier box to the slab with 3/8” standard threaded rod at the corresponding position.

NOTE: UVC lamps can be removed prior to installing the Air Purifier box if the UVC lamps will not be used.

A

enverid.com

enVerid Installation Guide

STEP 6 Power supply wiring: cabling should be contained within conduit, and connected to PCB board as shown.

STEP 7 Control panel wiring: The position of the control switch panel shall be decided and confirmed with client and/or main contractor.

Cabling should be contained within conduit and controller connected to panel board with RVSP line as shown.

STEP 8 Installation of filter: Please note that the arrow on the filter is the direction of air flow as below. Filters should be installed after cleaning work has been completed on-site.

The reset button on the Controller should be pressed once the filters are installed to reset the maintenance schedule for the filters. Once reset, the Filter Life counter in the Notification Center under the speed display will say 365 or 182 days to indicate a 12 or 6 month filter life. The high efficiency filter should be replaced every 6 months when the UVC lamp is used and every 12 months if the UVC lamp is not used by removing the UVC lamps from the unit. If the filter life shows 182 days and you are operating the system without the UVC lamp, then one maintenance schedule can be skipped each cycle. The counter is hard-coded to either 365 or 182 days.

NOTE: Filters should only be installed once the building is completely clean of construction debris and dust.

www.enverid.com

enVerid Installation Guide

enverid.com · 1.617.795.4000 · info@enverid.com Energy Savings. Air Quality.

©2020 enVerid Systems, Inc. All rights reserved. Third-party trademarks mentioned are the property of their respective owners. | 2020-09-02_AP_Install_v1

enVerid helps buildings achieve ESG (Environmental, Social, and Governance), healthy building, and cost saving goals by improving indoor air quality while saving money and reducing energy consumption and carbon emissions. For new HVAC systems, enVerid’s award-winning HVAC Load Reduction (HLR) Modules enable immediate capital cost savings. HLR Modules also deliver up to 30% energy savings and superior indoor air quality in new and existing buildings. enVerid’s air filtration products remove particulate and microorganism contamination from indoor air without the significant cost of upgrading mechanical systems and increasing mechanical ventilation rates. enVerid’s products are deployed in commercial, academic and government buildings globally. enVerid’s HLR Modules are ASHRAE Standard 62.1, LEED, and WELL compliant and eligible for utility rebates. For more information visit https://enverid.com.

4. enVerid Air Purifier Wiring Diagram