Upload
vuongtu
View
214
Download
0
Embed Size (px)
Citation preview
The best way to control airborne contaminants, fume and smoke in the workplace is to remove them right at source of their creation. Nederman FX2 arms offer unbeatable flexibility in combination with optimal efficiency and can be used in every type of environment. Multiple mounting options are available and the arms can be easily integrated with a complete Nederman filtration system.
Articulated extraction arms are the best and most cost-efficient solution for places where small extraction volumes are required within a limited area.
The handy solution for at-source extraction
A wide range of applicationsNederman FX2 extraction arms are especially suitable for applications where small, flexible and easy-to-use arms are required to eliminate smoke fumes, gases, dust, and particles. They capture the pollutants as close to the source as possible, so that a high capture rate is achieved with minimum energy use. Any hazardous airborne sub-stances are removed before they reach the breathing zone or contaminate premises and goods.
Nederman’s FX2 arms are available in three different models to cover a wide spectrum of needs. Common ap-plication areas are, for example: laboratories, electronics industry, 3D printing, health service and pharmacies, glu-ing stations, museums and hair and nail salons. Our team of air filtration experts will gladly help you select the right configuration to suit your particular requirements.
Clean air is a cornerstone of sustainable production. With more than 70 years of experience in extraction and filtra-tion of various air contaminants, Nederman is the global leader in industrial air filtration. Our goal is to protect people, planet and products from harmful effects of indus-trial processes. By doing that, we contribute to efficient production, environmental benefits and a safer workplace.
We deliver complete solutions that can easily be adapt-ed to your particular needs. Our services cover everything from initial analysis and planning to installation, training, service and maintenance. We aim to continually develop our offer by adding new products and services, expanding our geographic presence and helping our customers devel-op their processes for sustainable production.
People, planet and products
A sideways-positioned hood close to the bench gives you the best capture efficiency.
Did you know?
• Effective fume and dust extraction
• Low noise level and high energy efficiency
• Stable positioning with easy maneuverability
• Wide range available
• Aesthetic design
• Complete freedom when planning installation
• Maximum installation flexibility
Nederman FX2 in short
Scan the QR code to read our
whitepaper “Improve Air Quality
and Energy Efficiency by Optimizing
Capture Efficiency with Nederman
Articulated Extraction Arms (AEA)”.
Flexible. Energy-efficient. Quiet.
Nederman FX2 arms are made of lightweight anodized aluminium sections, with two or three adjustable, composite friction joints. Offering strength and durability combined with easy handling, they can be used in many types of environments. They are especially suitable for applications where small, flexible and easy-to-use arms are required.
Unique maneuverability Nederman FX2 arms are highly flexible, and simple to po-sition, extend and retract. The two outermost arm joints can rotate 360°. This makes it possible to position the hood exactly where required. Once correctly positioned, the hood can be locked in place using two friction devices in the arm joints.
Aesthetic designThe lean, smooth and aesthetic design allows Nederman FX2 arms to fit well in any environment without compromis-ing durability and reliability. The swivel design is optimized to ensure a slim profile and clear sight.
Thanks to the long upper arm section, the FX2 PLUS swivel and accessories can be placed high up or above a false ceiling. It creates a modern design that easily blends in and prevents dust accumulation.
Optimal efficiency and low noiseThe FX2 arms were developed using computerized simula-tions, and the resulting highly improved airflows mean that smaller fans that consume less energy are required. Anoth-er user benefit is the reduced noise level. Depending on the airflow, this means a reduction of about 5 dB or more, when compared with similar arms on the market. Complementary Nederman products such as fans, ducting and control units can further increase energy efficiency.
360°
360°
360°
Did you know?
Connection Up-PLUSMounting options: ceiling, wall
Connection DownMounting options: bench edge, floor, or any other horizontal surface
Connection UpMounting options: ceiling, wall, shelf edge, etc.
Connection Down-ThroughMounting options: through bench
Nederman FX2 arms for maximum flexibilityThe Nederman FX2 arms allow complete freedom when planning installation points. They can be mounted on ceilings, walls and floors or fixed to worktops.
Nederman FX2 arms are supplied with a mini hood
as standard – no extra extraction nozzle is required.
The mini hood is also a universal interface for con-
necting to other hoods: the ergonomically designed
combi hood, the dome hood, the flange hood and the
metal hood. All of them can be attached directly to the
mini hood, irrespective of arm size.
The FX 32 armA compact 32 mm one-piece, self-supporting, flexible arm for low-volume bench top extraction purposes. Made of acryloni-trile butadiene styrene (ABS) with no joints.
Adapt your installationNederman offers you a unique possibility to adapt the arm installation to your facilities. Cut2fit extension is an aluminium profile, which can be cut at any length and assembled together with the classic bracket for mount-ing arms to the ceiling or wall. With our cut2fit extension profile you are free to cut the profile length, which gives you unparalleled flexibility. In addition, we also provide complementary products such as filters, fans and control equipment that further let you adapt your installation.
Nederman FX2 arms are available in self-assembly kits, which include a fan, a filter, a fan speed controller, hoses, table bracket and connectors. No duct is needed. These kits provide a quick and conventient solution for creating a fume-free workplace.
A full rangeNederman FX2 arms present the most complete offering on the market. All arms are supplied with a mounted duct connector to facilitate coupling of external ductwork to the arm. The duct connector is made of rubber and fully leak-proof. All arms are equipped with a mini hood. No extra extraction nozzle is required when working close to the source.
The CHEM modelProfiles in anodized aluminium with a white electrophoretic deposition coating make the arm ideal for fume extraction in aggressive environ-ments where corrosion resistance must be assured.
Available in 2 diameters: 75 and 100 mm.
The Original modelA robust and reliable all-round arm for general applications where there is little risk of electrical discharges or attack by aggressive chemicals.
Available in 3 diameters: 50, 75 and 100 mm.
The ESD/EX modelThe arm is made of conductive ma-terials, eliminating the risk of static electricity and sparks. Designed for use in electronic environments where there is a risk of electrostatic dis-charges, the ESD/EX can also be used for certain applications in potentially explosive atmospheres.
Available in 3 diameters: 50, 75 and 100 mm.
Complete solutions that protect your workplace
Comprehensive product rangeNederman is a world-leading environmental technology company with solutions that take their origin in “capture-at-source”, i.e. extraction of contaminants right at the point of creation. We filter, clean and recycle to create eco-efficient production in demanding industrial surroundings. Our offer includes individual products, engineering design, installation, commissioning and service. By continually adding new skills and solutions and expanding our geographic presence, we help our customers to develop their businesses both economically and ecologically.
Worldwide presenceNederman has a strong global presence in both sales and production. We have our own sales companies in 25 countries and distributors in more than 30 countries. Production is performed in 12 countries on five continents. In many coun-tries, we also have a well-established service organization. By offering advanced service with high availability, Nederman helps customers to secure continuous, optimized production.
Extensive experienceFor more than 70 years, Nederman has developed prod-ucts and solutions to reduce the strain on the environ-ment and protect people from harmful particles, fibres, dust, gas, smoke and oil mist. We have extensive expe-rience in how to create a safe working environment. Our accumulated know-how is easily accessible when you plan a new facility or need to modernize existing operations.
All laboratory work during which gases, fumes and particles are handled in potentially hazardous quantities and concentrations must ensure efficient extraction and filtration. A well-designed and installed extraction system will not only increase safety, performance and efficiency, but will also minimize running costs and noise levels.
Articulated extraction arms are the best and most cost-efficient solution for places where small extraction volumes are required within a limited area. They can also be used when the pollution source is too large to be reasonably enclosed in a cupboard and has distinct points where the pollution might appear.
Maximize capture efficiencyThere are many parameters that affect the articulated ex-traction arm’s capture efficiency. Some of them are cross-draught caused by background ventilation, placement of other equipment, operator position and movement, and arm position. It is not always possible to control all of these parameters.
However, the optimized shape of Nederman’s FX2 joints helps maximize airflow while minimizing pressure drop. The integrated mini hood enlarges the capture zone significantly when working close to the source. If the pollution source is located further away, Nederman offers extended capture hoods for maximum performance.
The handy solution for at-source extraction
Clean air is a cornerstone of sustainable production. With more than 70 years of experience in extraction and filtra-tion of various air contaminants, Nederman is the global leader in industrial air filtration. Our goal is to protect people, planet and products from harmful effects of indus-trial processes. By doing that, we contribute to efficient production, environmental benefits and a safer workplace.
We deliver complete solutions that can easily be adapt-ed to your particular needs. Our services cover everything from initial analysis and planning to installation, training, service and maintenance. We aim to continually develop our offer by adding new products and services, expanding our geographic presence and helping our customers devel-op their processes for sustainable production.
People, planet and products
Scan the QR code to read our
whitepaper “Improve Air Quality
and Energy Efficiency by Optimizing
Capture Efficiency with Nederman
Articulated Extraction Arms (AEA)”.
• Effective fume and dust extraction
• Low noise level and high energy efficiency
• Stable positioning with easy maneuverability
• Wide range available
• Aesthetic design
• Complete freedom when planning installation
• Maximum installation flexibility
Nederman FX2 in short
A sideways-positioned hood close to the bench gives you the best capture efficiency.
Did you know?
Clean. Energy-efficient. Quiet.
Nederman FX2 arms are made of lightweight anodized aluminium sections, with two or three adjustable, composite friction joints. Offering strength and durability combined with easy handling, they can be used in many types of environments. They are especially suitable for applications where small, flexible and easy-to-use arms are required.
Unique maneuverability Nederman FX2 arms are highly flexible, and simple to po-sition, extend and retract. The two outermost arm joints can rotate 360°. This makes it possible to position the hood exactly where required. Once correctly positioned, the hood can be locked in place using two friction devices in the arm joints.
Aesthetic designThe lean, smooth and aesthetic design allows Nederman FX2 arms to fit in well in a laboratory environment without compromising its durability and reliability. The swivel design is optimized to ensure a slim profile and clear sight.
Thanks to the long upper arm section, the FX2 PLUS swivel and accessories can be placed high up or above a false ceiling. It creates a modern design that easily blends in and prevents dust accumulation.
Optimal efficiency and low noiseThe FX2 arms were developed using computerized simula-tions, and the resulting highly improved airflows mean that smaller fans that consume less energy are required. Anoth-er user benefit is the reduced noise level. Depending on the airflow, this means a reduction of about 5 dB or more, when compared with similar arms on the market. Complementary Nederman products such as fans, ducting and control units can further increase energy efficiency.
360°
360°
360°
The CHEM modelProfiles in anodized aluminium with a white electrophoretic deposition coating make the arm ideal for fume extraction in aggressive environ-ments where corrosion resistance must be assured.
Available in 2 diameters: 75 and 100 mm.
Did you know?Nederman FX2 arms are supplied with a mini hood
as standard – no extra extraction nozzle is required.
The mini hood is also a universal interface for con-
necting to other hoods: the ergonomically designed
combi hood, the dome hood, the flange hood and the
metal hood. All of them can be attached directly to the
mini hood, irrespective of arm size.
The FX2 range
The Original modelA robust and reliable all-round arm for general applications where there is little risk of electrical discharges or attack by aggressive chemicals.
Available in 3 diameters: 50, 75 and 100 mm.
The ESD/EX modelThe arm is made of conductive ma-terials, eliminating the risk of static electricity and sparks. Designed for use in electronic environments where there is a risk of electrostatic dis-charges, the ESD/EX can also be used for certain applications in potentially explosive atmospheres.
Available in 3 diameters: 50, 75 and 100 mm.
Nederman FX2 arms present the most complete offering on the market. All arms are supplied with a mounted duct connector to facilitate coupling of external ductwork to the arm. The duct connector is made of rubber and fully
leak-proof. All arms are equipped with a mini hood. No ex-tra extraction nozzle is required when working close to the source.
Adapt your installationNederman offers you a unique possibility to adapt the arm installation to your facilities. Cut2fit extension is an alu-minium profile, which can be cut at any length and assem-bled together with the classic bracket for mounting arms to the ceiling or wall. With our cut2fit extension profile you are free to cut the profile length, which gives you unparal-leled flexibility. In addition, we also provide complementary products such as filters, fans and control equipment that further let you adapt your installation.
Nederman FX2 arms are available in self-assembly kits, which include a fan, a filter, a fan speed controller, hoses, table bracket and connectors. No duct is needed. These kits provide a quick and conventient solution for creating a fume-free workplace.
Nederman FX2 arms for maximum flexibilityThe Nederman FX2 arms allow complete freedom when planning installation points. They can be mounted on ceilings, walls and floors or fixed to worktops.
Connection Up-PLUSMounting options: ceiling, wall
Connection DownMounting options: bench edge, floor, or any other horizontal surface
Connection UpMounting options: ceiling, wall, shelf edge, etc.
Connection Down-ThroughMounting options: through bench
Complete solutions that protect your workplace
Comprehensive product rangeNederman is a world-leading environmental technology company with solutions that take their origin in “capture-at-source”, i.e. extraction of contaminants right at the point of creation. We filter, clean and recycle to create eco-efficient production in demanding industrial surroundings. Our offer includes individual products, engineering design, installation, commissioning and service. By continually adding new skills and solutions and expanding our geographic presence, we help our customers to develop their businesses both economically and ecologically.
Worldwide presenceNederman has a strong global presence in both sales and production. We have our own sales companies in 25 countries and distributors in more than 30 countries. Production is performed in 12 countries on five continents. In many coun-tries, we also have a well-established service organization. By offering advanced service with high availability, Nederman helps customers to secure continuous, optimized production.
Extensive experienceFor more than 70 years, Nederman has developed prod-ucts and solutions to reduce the strain on the environ-ment and protect people from harmful particles, fibres, dust, gas, smoke and oil mist. We have extensive expe-rience in how to create a safe working environment. Our accumulated know-how is easily accessible when you plan a new facility or need to modernize existing operations.
nederman.com
Nederman is a world-leading environmental technology company. We filter, clean and recycle to create eco-efficient production in demanding industrial surroundings.
For more than 70 years, Nederman has developed, manufactured, and installed products and solutions to reduce the strain on the environment and improve working conditions in numerous industries. Our products and systems have been ground-breaking in industries such as machining, metal fabrication, mining, auto motive, composite manufacturing, food, pharmaceuticals, wood-working, and many others.
BenchTop Extraction Arm FX2 50 OriginalThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with two or three adjustable, composite friction joints.Offering strength and durability combined with easy handling, theycan be used in many types of environment. They are especiallysuitable for applications where small, flexible and easy-to-use armsare required.A robust and reliable all-round arm for general applications wherethere is little risk of electrical discharges or attack by aggressivechemicals.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX250 Original
Noise level (dB(A)) 60 dB(A) at 110 m3/hInstallation IndoorMaterial Tubes in anodizied aluminium.
Joints in PP plastic.Duct connectors in EPDMrubber.Minihood in PP plastic.
Fume temperature max 70°CExtraction arm diameter (mm) 50Airflow (m3/h) 50-110Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 1 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Image Description Weight (kg) Model
FX2-ORIG-D50-L700-Up/Down-Low 1,7 70600144
FX2-ORIG-D50-L700-Up-PLUS 2,7 70600244
FX2-ORIG-D50-L700-Up/Down-Through 1,2 70600344
FX2-ORIG-D50-L1100-Up-Low 2,3 70600444
FX2-ORIG-D50-L1100-Up-PLUS 3,3 70600544
FX2-ORIG-D50-L1100-Down-Low 2,3 70600644
FX2-ORIG-D50-L1100-Down-Through 1,8 70600744
FX2-ORIG-D50-L1500-Up-Low 2,6 70600844
FX2-ORIG-D50-L1500-Up-PLUS 3,6 70600944
FX2-ORIG-D50-L1500-Down-Low 2,6 70601044
FX2-ORIG-D50-L1500-Down-Through 2,1 70601144
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 2 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Wall BRKT kit-Flat-L190-White.Complete mounting kit, with flat wall bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall.
70377043
FX2-Wall-P BRKT kit-D50/75/100-L190.Complete mounting kit for mounting FX2 50/75/100 plus arms with 250 mm (9.84 inch)from the vertical centre line of the arm to the wall.
70377046
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX-Combi hood-ORIGINAL-D50/75/100.Transparant combi hood, made of PET-G plastic, arms is designed to capturecontaminants with low energy. It can be attached directly on minihood, irrespective of armsize. The ergonomics of handle design on both sides of the hood make it easier tomaneuver.
70500144
FX-Dome hood-ORIGINAL-D50/75/100.Transparent dome hood, made of PET-G plastic, is designed to capture high dispersioncontaminants. It can be attached directly on minihood, irrespective of arm size. Theergonomics of handle design on both sides of the hood make it easier to maneuver.
70376982
FX-Metal hood-ORIG/CHEM-D50/75/100.Powder coated white metal hood, made of aluminum, is designed to capturecontaminants in high temperature, aggressive fume where corrosion resistance must beassured or dust splatter. It can be attached directly on minihood, irrespective of arm size.
70500444
FX-Flange hood-ORIGINAL-D50/75/100.Transparent flange hood, made of PET-G plastic, is designed to maximize the capturezone without hinder objects on the bench or the user. It can be attached directly onminihood, irrespective of arm size.
70502844
FX2-Al duct-L1000-D50toD77.Aluminum duct with 77 mm ( 3 inch) diameter and 1000 mm (39.37 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 50 arm. This is agood looking alternative to standard, ventilation duct.
70377056
FX-Hose-D75-L3000-Grey-Flexible hose in grey PVC with 75 mm (3 inch) diameter and 3000 mm (118.11 inch)length. It shall be used with hose support ring to connect hose to arm.
70377098
FX2-Hose support ring-D75.Place into the 75 mm (3 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377067
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 3 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 4 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Material:1) Flange: PP
2) Tubes: Aluminum, anodized 10 µm
3) Damper adjustment handle: Aluminum, anodized 10 µm Internal spring: Staineless steel Damper blade: Conductive TP & PP plastic
4) Joints: PP with glass fibre reinforcement Plastic rings: PP with glass fibre reinforcement Axial locking rings: PP with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: EPDM Rubber
6) Swivel: Aluminum, powder coating Rivets: Aluminum Bearings swivel: PP plastic with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 5 9/22/2017
BenchTop Extraction Arm FX2 50 Original
• FX2-ORIG-D50-L700-Up/Down-LowPart number: 70600144Max. working radius: 630 mm (24,8 in)A: 400 mm (15,7 in)
• FX2-ORIG-D50-L1100-Up-LowPart number: 70600444Max. working radius: 1030 mm (40,5 in)A: 400 mm (15,7 in)B: 400 mm (15,7 in)
•FX2-ORIG-D50-L1500-Up-LowPart number: 70600844Max. working radius: 1430 mm (56,3 in)A: 500 mm (19,7 in)B: 700 mm (27,6 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 6 9/22/2017
BenchTop Extraction Arm FX2 50 Original
• FX2-ORIG-D50-L700-Up/Down-LowPart number: 70600144Max. working radius: 630 mm (24,8 in)A: 400 mm (15,7 in)
• FX2-ORIG-D50-L1100-Down-LowPart number: 70600644Max. working radius: 1030 mm (40,5 in)A: 400 mm (15,7 in)B: 400 mm (15,7 in)
• FX2-ORIG-D50-L1500-Down-LowPart number: 70601044Max. working radius: 1430 mm (56,3 in)A: 500 mm (19,7 in)B: 700 mm (27,6 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 7 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Part number: 70600344Max. working radius: 630 mm (24,8 in)A: 400 mm (15,7 in)
• FX2-ORIG-D50-L1100-Down-ThroughPart number: 70600744Max. working radius: 1030 mm (40,5 in)A: 400 mm (15,7 in)B: 400 mm (15,7 in)
• FX2-ORIG-D50-L1500-Down-ThroughPart number: 70601144Max. working radius: 1430 mm (56,3 in)A: 500 mm (19,7 in)B: 700 mm (27,6 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 8 9/22/2017
BenchTop Extraction Arm FX2 50 Original
• FX2-ORIG-D50-L700-Up-PLUSPart number: 70600244Max. working radius: 630 mm (24,8 inch)A: 400 mm (15,7 in)
• FX2-ORIG-D50-L1100-Up-PLUSPart number: 70600544Max. working radius: 1030 mm (40,5 in)A: 400 mm (15,75in)B: 400 mm (15,7 in)
• FX2-ORIG-D50-L1500-Up-PLUSPart number: 70600944Max. working radius: 1430 mm (56,3 in)A: 500 mm (19,7 in)B: 700 mm (27,6 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 9 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Wall mounting examples:Left: FX2-Up-PLUS arm with following accessories:-FX2-Wall-P BRKT kit-D50/75/100-L190-FX2-Ceiling cover plate-PLUS
Middle: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D75
Right: Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-White-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D75
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 10 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 11 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Ceiling mounting example:Left: FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D75-FX-Ceiling cover plate
Right: FX2-Up-PLUS arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 12 9/22/2017
BenchTop Extraction Arm FX2 50 Original
Other mounting examples:Left: Over bench cabinet mounting with FX2-Up/Down-Through arm
Middle: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
Right: Floor mounting with FX2-Up-Low arm and following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © 2016 Nederman Holding AB
www.nederman.com 13 9/22/2017
BenchTop Extraction Arm FX2 75 OriginalThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with three adjustable, composite friction joints. Offeringstrength and durability combined with easy handling, they can beused in many types of environment. They are especially suitable forapplications where small, flexible and easy-to-use arms arerequired.A robust and reliable all-round arm for general applications wherethere is little risk of electrical discharges or attack by aggressivechemicals.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX275 Original
Noise level (dB(A)) 58 dB(A) at 240 m3/hInstallation IndoorMaterial Tubes in anodizied aluminium.
Joints in PP plastic.Duct connectors in EPDMrubber.Minihood in PP plastic.
Fume temperature max 70°CExtraction arm diameter (mm) 75Airflow (m3/h) 110-240Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 1 1/26/2018
BenchTop Extraction Arm FX2 75 Original
Image Description Weight (kg) Model
FX2-ORIG-D75-L1100-Up-Low 3,2 70602344
FX2-ORIG-D75-L1100-Up-PLUS 4,5 70602444
FX2-ORIG-D75-L1100-Down-Low 3,2 70602544
FX2-ORIG-D75-L1100-Down-Through 2,6 70602644
FX2-ORIG-D75-L1500-Up-Low 3,4 70602744
FX2-ORIG-D75-L1500-Up-PLUS 4,7 70602844
FX2-ORIG-D75-L1500-Down-Low 3,4 70602944
FX2-ORIG-D75-L1500-Down-Through 2,8 70603044
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 2 1/26/2018
BenchTop Extraction Arm FX2 75 Original
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Wall BRKT kit-Flat-L190-White.Complete mounting kit, with flat wall bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall.
70377043
FX2-Wall-P BRKT kit-D50/75/100-L190.Complete mounting kit for mounting FX2 50/75/100 plus arms with 250 mm (9.84 inch)from the vertical centre line of the arm to the wall.
70377046
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX-Combi hood-ORIGINAL-D50/75/100.Transparant combi hood, made of PET-G plastic, arms is designed to capturecontaminants with low energy. It can be attached directly on minihood, irrespective of armsize. The ergonomics of handle design on both sides of the hood make it easier tomaneuver.
70500144
FX-Dome hood-ORIGINAL-D50/75/100.Transparent dome hood, made of PET-G plastic, is designed to capture high dispersioncontaminants. It can be attached directly on minihood, irrespective of arm size. Theergonomics of handle design on both sides of the hood make it easier to maneuver.
70376982
FX-Metal hood-ORIG/CHEM-D50/75/100.Powder coated white metal hood, made of aluminum, is designed to capturecontaminants in high temperature, aggressive fume where corrosion resistance must beassured or dust splatter. It can be attached directly on minihood, irrespective of arm size.
70500444
FX-Flange hood-ORIGINAL-D50/75/100.Transparent flange hood, made of PET-G plastic, is designed to maximize the capturezone without hinder objects on the bench or the user. It can be attached directly onminihood, irrespective of arm size.
70502844
FX2-Duct connector-ORIG/CHEM-D100.Grey duct connector to ease the coupling of 100mm (4 inch) Alu duct to external 125mm(5 inch) ductwork. Please note all arms are already supplied with a duct connector asstandard.
70377040
FX2-Al duct-L1000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 1000 mm (39.37 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377058
FX2-Al duct-L2000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 2000 mm (78.74 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377059
FX-Hose-D75-L3000-Grey-Flexible hose in grey PVC with 75 mm (3 inch) diameter and 3000 mm (118.11 inch)length. It shall be used with hose support ring to connect hose to arm.
70377098
FX-Hose-D100-L3000-Grey-Flexible hose in grey PVC with 100 mm (4 inch) diameter and 3000 mm (118.11 inch)length. It shall be used with hose support ring to connect hose to arm.
70377099
FX2-Hose support ring-D75.Place into the 75 mm (3 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377067
FX2-Hose support ring-D100.Place into the 100 mm (4 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377068
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 3 1/26/2018
BenchTop Extraction Arm FX2 75 Original
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 4 1/26/2018
BenchTop Extraction Arm FX2 75 Original
Material:1) Flange: PP
2) Tubes: Aluminum, anodized 10 µm
3) Damper adjustment handle: Aluminum, anodized 10 µm Internal spring: Staineless steel Damper blade: Conductive TP & PP plastic
4) Joints: PP with glass fibre reinforcement Plastic rings: PP with glass fibre reinforcement Axial locking rings: PP with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: EPDM Rubber
6) Swivel: Aluminum, powder coating Rivets: Aluminum Bearings swivel: PP plastic with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 5 1/26/2018
BenchTop Extraction Arm FX2 75 Original
• FX2-ORIG-D75-L1100-Up-LowPart number: 70602344Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 inch)B: 420 mm (16,5 inch)
• FX2-ORIG-D75-L1500-Up-LowPart number: 70602744Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 6 1/26/2018
BenchTop Extraction Arm FX2 75 Original
FX2-ORIG-D75-L1100-Up-PLUSPart number: 70602444Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-ORIG-D75-L1500-Up-PLUSPart number: 70602844Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 7 1/26/2018
BenchTop Extraction Arm FX2 75 Original
• FX2-ORIG-D75-L1100-Down-LowPart number: 70602544Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-ORIG-D75-L1500-Down-LowPart number: 70602944Max. working radius: 1450 (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 8 1/26/2018
BenchTop Extraction Arm FX2 75 Original
• FX2-ORIG-D75-L1100-Down-ThroughPart number: 70602644Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-ORIG-D75-L1500-Down-ThroughPart number: 70603044Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 9 1/26/2018
BenchTop Extraction Arm FX2 75 Original
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 10 1/26/2018
BenchTop Extraction Arm FX2 75 Original
Ceiling mounting example:Left: FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D100-FX-Ceiling cover plate
Right: FX2-Up-PLUS arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS
Other mounting examples:Left: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
Right: Floor mounting with FX2-Up-Low arm and following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 11 1/26/2018
BenchTop Extraction Arm FX2 75 Original
Wall mounting examples:Left: FX2-Up-PLUS arm with following accessories:-FX2-Wall-P BRKT kit-D50/75/100-L190-FX2-Ceiling cover plate-PLUS
Middle: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D100
Right: Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-White-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 12 1/26/2018
BenchTop Extraction Arm FX2 100 OriginalThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with three adjustable, composite friction joints. Offeringstrength and durability combined with easy handling, they can beused in many types of environment. They are especially suitable forapplications where small, flexible and easy-to-use arms arerequired.A robust and reliable all-round arm for general applications wherethere is little risk of electrical discharges or attack by aggressivechemicals.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX2100 Original
Noise level (dB(A)) 62 dB(A) at 450 m3/hInstallation IndoorMaterial Tubes in anodizied aluminium.
Joints in PP plastic.Duct connectors in EPDMrubber.Minihood in PP plastic.
Fume temperature max 70°CExtraction arm diameter (mm) 100Airflow (m3/h) 200-450Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 1 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Image Description Weight (kg) Model
FX2-ORIG-D100-L1200-Up/Down-Low 4,8 70604744
FX2-ORIG-D100-L1200-Up-PLUS 5,9 70604844
FX2-ORIG-D100-L1200-Up/Down-Thr 4,1 70604944
FX2-ORIG-D100-L1800-Up-Low 5,9 70605044
FX2-ORIG-D100-L1800-Up-PLUS 7,7 70605144
FX2-ORIG-D100-L1800-Down-Low 5,9 70605244
FX2-ORIG-D100-L1800-Down-Through 5,2 70605344
FX2-ORIG-D100-L2400-Up-Low 6,9 70605444
FX2-ORIG-D100-L2400-Up-PLUS 8,7 70605544
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 2 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Wall BRKT kit-Flat-L190-White.Complete mounting kit, with flat wall bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall.
70377043
FX2-Wall-P BRKT kit-D50/75/100-L190.Complete mounting kit for mounting FX2 50/75/100 plus arms with 250 mm (9.84 inch)from the vertical centre line of the arm to the wall.
70377046
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX-Combi hood-ORIGINAL-D50/75/100.Transparant combi hood, made of PET-G plastic, arms is designed to capturecontaminants with low energy. It can be attached directly on minihood, irrespective of armsize. The ergonomics of handle design on both sides of the hood make it easier tomaneuver.
70500144
FX-Dome hood-ORIGINAL-D50/75/100.Transparent dome hood, made of PET-G plastic, is designed to capture high dispersioncontaminants. It can be attached directly on minihood, irrespective of arm size. Theergonomics of handle design on both sides of the hood make it easier to maneuver.
70376982
FX-Metal hood-ORIG/CHEM-D50/75/100.Powder coated white metal hood, made of aluminum, is designed to capturecontaminants in high temperature, aggressive fume where corrosion resistance must beassured or dust splatter. It can be attached directly on minihood, irrespective of arm size.
70500444
FX-Flange hood-ORIGINAL-D50/75/100.Transparent flange hood, made of PET-G plastic, is designed to maximize the capturezone without hinder objects on the bench or the user. It can be attached directly onminihood, irrespective of arm size.
70502844
FX2-Duct connector-ORIG/CHEM-D100.Grey duct connector to ease the coupling of 100mm (4 inch) Alu duct to external 125mm(5 inch) ductwork. Please note all arms are already supplied with a duct connector asstandard.
70377040
FX2-Al duct-L1000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 1000 mm (39.37 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377058
FX2-Al duct-L2000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 2000 mm (78.74 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377059
FX-Hose-D100-L3000-Grey-Flexible hose in grey PVC with 100 mm (4 inch) diameter and 3000 mm (118.11 inch)length. It shall be used with hose support ring to connect hose to arm.
70377099
FX-Hose D125-L5000-Grey-Flexible hose in grey PVC with 125 mm (5 inch) diameter and 5000 mm (195.85 inch)length. It shall be used with hose support ring to connect hose to arm.
70377100
FX2-Hose support ring-D100.Place into the 100 mm (4 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377068
FX2-Hose support ring-D125.Place into the 125 mm ( 5 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377069
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 3 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 4 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Material:1) Flange: PP
2) Tubes: Aluminum, anodized 10 µm
3) Damper adjustment handle: Aluminum, anodized 10 µm Internal spring: Staineless steel Damper blade: Conductive TP & PP plastic
4) Joints: PP with glass fibre reinforcement Plastic rings: PP with glass fibre reinforcement Axial locking rings: PP with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: EPDM Rubber
6) Swivel: Aluminum, powder coating Rivets: Aluminum Bearings swivel: PP plastic with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 5 1/26/2018
BenchTop Extraction Arm FX2 100 Original
• FX2-ORIG-D100-L1200-Up/Down-LowPart number: 70604744Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-ORIG-D100-L1800-Down-LowPart number: 70605244Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 6 1/26/2018
BenchTop Extraction Arm FX2 100 Original
• FX2-ORIG-D100-L1200-Up/Down-ThroughPart number: 70604944Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-ORIG-D100-L1800-Down-ThroughPart number: 70605344Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 7 1/26/2018
BenchTop Extraction Arm FX2 100 Original
• FX2-ORIG-D100-L1200-Up/Down-LowPart number: 70604744Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-ORIG-D100-L1800-Up-LowPart number: 70605044Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
*• FX2-ORIG-D100-L2400-Up-LowPart number: 70605444Max. working radius: 2290 mm (90,2 in)A: 1010 mm (39,7 in)B: 1010 mm (39,7 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 8 1/26/2018
BenchTop Extraction Arm FX2 100 Original
FX2-ORIG-D100-L1200-Up-PLUSPart number: 70604844Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-ORIG-D100-L1800-Up-PLUSPart number: 70605144Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
• FX2-ORIG-D100-L2400-Up-PLUSPart number: 70605544Max. working radius: 2290 mm (90,2 in)A: 1010 mm (39,7 in)B: 1010 mm (39,7 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 9 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 10 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Ceiling mounting example:Left: FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D100-FX-Ceiling cover plate
Right: FX2-Up-PLUS arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 11 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Other mounting examples:Left: Overbench cabinet mounting with FX2-Up/Down-Through arm
Middle: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
Right: Floor mounting with FX2-Up-Low arm and following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 12 1/26/2018
BenchTop Extraction Arm FX2 100 Original
Wall mounting examples:Left: FX2-Up-PLUS arm with following accessories:-FX2-Wall-P BRKT kit-D50/75/100-L190-FX2-Ceiling cover plate-PLUS
Middle: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D100
Right: FX2-Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-White-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ORIG/CHEM-D100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 13 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EXThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with two or three adjustable, composite friction joints.Offering strength and durability combined with easy handling, theycan be used in many types of environment. They are especiallysuitable for applications where small, flexible and easy-to-use armsare required.The arm is designed for use in electronic environments where thereis a risk of electrostatic discharges. The ESD/EX can also be usedfor certain applications in potentially explosive atmospheres.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX250 ESD/EX
Noise level (dB(A)) 60 dB(A) at 110 m3/hInstallation IndoorMaterial Tubes in anodized aluminium.
Joints in conductive PP plastic.Duct connector in conductiveEPDM rubber.Minihood in conductive PPplastic.
Fume temperature max 70°CExtraction arm diameter (mm) 50Airflow (m3/h) 50 - 110Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 1 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Image Description Weight (kg) Model
FX2-ESD/EX-D50-L700-Up/Down-Low 1,7 70601244
FX2-ESD/EX-D50-L700-Up/Dow-Through 1,2 70601444
FX2-ESD/EX-D50-L1100-Up-Low 2,3 70601544
FX2-ESD/EX-D50-L1100-Down-Low 2,3 70601744
FX2-ESD/EX-D50-L1100-Down-Through 1,8 70601844
FX2-ESD/EX-D50-L1500-Up-Low 2,6 70601944
FX2-ESD/EX-D50-L1500-Down-Low 2,6 70602144
FX2-ESD/EX-D50-L1500-Down-Through 2,1 70602244
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 2 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Wall BRKT kit-Flat-L190-Black.Complete mounting kit, with flat wall bracke,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250 mm (9.84 inch) from thevertical centre line of the arm to the wall.
70377044
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX-Combi hood-ESD/EX-D50/75/100.Black combi hood, made of conductive ABS plastic, is designed to capture low energycontamiants which is explosive or has a risk of electrostatic discharges. It can beattached directly on minihood, irrespective of arm size.The ergonomics of handle designon both sides of the hood make it easier to maneuver.
70500244
FX-Dome hood-ESD/EX-D50/75/100.Black dome hood, made of conductive ABS plastic,is designed to capture high dispersioncontaminants, which is explosive or has a risk of electrostatic discharges. It can beattached directly on minihood, irrespective of arm size. The ergonomics of handle designon both sides of the hood make it easier to maneuver.
70376983
FX-Metal hood-ESD/EX-D50/75/100.ESD conductive black metal hood, made of anodized aluminum, is designed to capturecontamiants in high temperature, aggressive fume where corrosion resistance must beassured or explosive dust splatter. It can be attached directly on minihood, irrespective ofarm size.
70500544
FX-Flange hood-ESD/EX-D50/75/100.Black flange hood, made of conductive ABS plastic, is designed to maximize the capturezone without hinder objects on the bench or the user. It can be attached directly onminihood, irrespective of arm size.
70502944
FX2-Duct connector-ESD/EX-D50.Conductive black duct connector to ease the coupling of 77mm Alu duct to external80mm ductwork. Please note all arms are already supplied with a duct connector asstandard.
70377037
FX2-Al duct-L1000-D50toD77.Aluminum duct with 77 mm ( 3 inch) diameter and 1000 mm (39.37 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 50 arm. This is agood looking alternative to standard, ventilation duct.
70377056
FX2-Al duct-L2000-D50toD77.Aluminum duct with 77 mm (3 inch) diameter and 2000 mm (78.74 inch) length isdesigned to replace vertical ventilation duct abovethe swivel of FX2 50 arm. This is agood looking alternative to standard, ventilation duct.
70377057
FX-Hose-ESD-D75-L3000-Black-Flexible hose in black conductive PE with 75 mm (3 inch) diameter and 3000 mm (118.11inch) length. It shall be used with hose support ring to connect hose to arm.
70377101
FX2-Hose support ring-D75.Place into the 75 mm (3 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377067
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 3 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 4 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Material:1) Flange: Conductive PP plastic
2) Tubes: Aluminum, anodized 10 µm
3) Damper adjustment handle: Aluminum: anodized 10 µm Internal spring: Stainless steel Damper blade: Conductive TP & PP plastic
4) Joints conductive: PP plastic with glass fibre reinforcement Plastic rings conductive: PP plastic with glass fibre reinforcement Axial locking rings conductive: PP plastic with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: conductive EPDM Rubber
6) Swivel: Aluminum, conductive powder coating Rivets: Aluminum Bearings swivel condutive: PP plastic with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 5 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
• FX2-ESD/EX-D50-L700-Up/Down-LowPart number: (70601244)Max. working radius: 630 mm (24,8 in)A: 400 mm (15,7 in)
• FX2-ESD/EX-D50-L1100-Down-LowPart number: 70601744Max. working radius: 1030 mm (40,5 in)A: 400 mm (15,7 in)B: 400 mm (15,7 in)
• FX2-ESD/EX-D50-L1500-Down-LowPart number: 70602144Max. working radius: 1430 mm (56,3 in)A: 500 mm (19,7 in)B: 700 mm (27,6 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 6 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
• FX2-ESD/EX-D50-L700-Up/Dow-ThroughPart number: 70601444Max. working radius: 630 mm (24,8 in)A: 400 mm (15,7 in)
• FX2-ESD/EX-D50-L1100-Down-ThroughPart number: 70601844Max. working radius: 1030 mm (40,5 in)A: 400 mm (15,7 in)B: 400 mm (15,7 in)
• FX2-ESD/EX-D50-L1500-Down-ThroughPart number: 70602244Max. working radius: 1430 mm (56,3 in)A: 500 mm (19,7 in)B: 700 mm (27,6 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 7 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
• FX2-ESD/EX-D50-L700-Up/Down-LowPart number: (70601244)Max. working radius: 630 mm (24,8 in)A: 400 mm (15,7 in)
• FX2-ESD/EX-D50-L1100-Up-LowPart number: 70601544Max. working radius: 1030 mm (40,5 in)A: 400 mm (15,7 in)B: 400 mm (15,7 in)
• FX2-ESD/EX-D50-L1500-Up-LowPart number: 70601944Max. working radius: 1430 mm (56,3 in)A: 500 mm (19,7 in)B: 700 mm (27,6 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 8 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Wall mounting examples:Left: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ESD/EX-D75
Right: Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-Black-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ESD/EX-D75
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 9 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Other mounting examples:Left: Overbench cabinet mounting with FX2-Up/Down-Through arm
Middle: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
Right: Floor mounting with FX2-Up-Low arm and following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 10 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 11 1/26/2018
BenchTop Extraction Arm FX2 50 ESD/EX
Ceiling mounting example:Left: FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-FX2-Duct connector-ESD/EX-D75-FX-Ceiling cover plate
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 12 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EXThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with two or three adjustable, composite friction joints.Offering strength and durability combined with easy handling, theycan be used in many types of environment. They are especiallysuitable for applications where small, flexible and easy-to-use armsare required.The arm is designed for use in electronic environments where thereis a risk of electrostatic discharges. The ESD/EX can also be usedfor certain applications in potentially explosive atmospheres.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX275 ESD/EX
Noise level (dB(A)) 58 dB(A) at 240 m3/hInstallation IndoorMaterial Tubes in anodized aluminium.
Joints in conductive PP plastic.Duct connector in conductiveEPDM rubber.Minihood in conductive PPplastic.
Fume temperature max 70°CExtraction arm diameter (mm) 75Airflow (m3/h) 110 - 240Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 1 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
Image Description Weight (kg) Model
FX2-ESD/EX-D75-L1100-Up-Low 3,2 70603944
FX2-ESD/EX-D75-L1100-Down-Low 3,2 70604144
FX2-ESD/EX-D75-L1100-Down-Through 2,6 70604244
FX2-ESD/EX-D75-L1500-Up-Low 3,4 70604344
FX2-ESD/EX-D75-L1500-Down-Low 3,4 70604544
FX2-ESD/EX-D75-L1500-Down-Through 2,8 70604644
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 2 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Wall BRKT kit-Flat-L190-Black.Complete mounting kit, with flat wall bracke,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250 mm (9.84 inch) from thevertical centre line of the arm to the wall.
70377044
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX-Combi hood-ESD/EX-D50/75/100.Black combi hood, made of conductive ABS plastic, is designed to capture low energycontamiants which is explosive or has a risk of electrostatic discharges. It can beattached directly on minihood, irrespective of arm size.The ergonomics of handle designon both sides of the hood make it easier to maneuver.
70500244
FX-Dome hood-ESD/EX-D50/75/100.Black dome hood, made of conductive ABS plastic,is designed to capture high dispersioncontaminants, which is explosive or has a risk of electrostatic discharges. It can beattached directly on minihood, irrespective of arm size. The ergonomics of handle designon both sides of the hood make it easier to maneuver.
70376983
FX-Metal hood-ESD/EX-D50/75/100.ESD conductive black metal hood, made of anodized aluminum, is designed to capturecontamiants in high temperature, aggressive fume where corrosion resistance must beassured or explosive dust splatter. It can be attached directly on minihood, irrespective ofarm size.
70500544
FX-Flange hood-ESD/EX-D50/75/100.Black flange hood, made of conductive ABS plastic, is designed to maximize the capturezone without hinder objects on the bench or the user. It can be attached directly onminihood, irrespective of arm size.
70502944
FX2-Duct connector-ESD/EX-D75.Conductive black duct connector to ease the coupling of 77mm (3 inch) Alu duct toexternal 100mm (4 inch) ductwork. Please note all arms are already supplied with a ductconnector as standard.
70377039
FX2-Al duct-L1000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 1000 mm (39.37 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377058
FX2-Al duct-L2000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 2000 mm (78.74 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377059
FX-Hose-ESD-D75-L3000-Black-Flexible hose in black conductive PE with 75 mm (3 inch) diameter and 3000 mm (118.11inch) length. It shall be used with hose support ring to connect hose to arm.
70377101
FX-Hose-ESD-D100-L3000-Black-Flexible hose in black conductive PE with 100 mm (4 inch) diameter and 3000 mm(118.11 inch) length. It shall be used with hose support ring to connect hose to arm.
70377102
FX2-Hose support ring-D75.Place into the 75 mm (3 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377067
FX2-Hose support ring-D100.Place into the 100 mm (4 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377068
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 3 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 4 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
Material:1) Flange: Conductive PP plastic
2) Tubes: Aluminum, anodized 10 µm
3) Damper adjustment handle: Aluminum: anodized 10 µm Internal spring: Stainless steel Damper blade: Conductive TP & PP plastic
4) Joints conductive: PP plastic with glass fibre reinforcement Plastic rings conductive: PP plastic with glass fibre reinforcement Axial locking rings conductive: PP plastic with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: conductive EPDM Rubber
6) Swivel: Aluminum, conductive powder coating Rivets: Aluminum Bearings swivel condutive: PP plastic with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 5 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
• FX2-ESD/EX-D75-L1100-Down-ThroughPart number: 70604244Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-ESD/EX-D75-L1500-Down-ThroughPart number: 70604644Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 6 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
• FX2-ESD/EX-D75-L1100-Up-LowPart number: 70603944Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-ESD/EX-D75-L1500-Up-LowPart number: 70604344Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 7 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
• FX2-ESD/EX-D75-L1100-Down-LowPart number: 70604144Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-ESD/EX-D75-L1500-Down-LowPart number: 70604544Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 8 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
Wall mounting examples:Left: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ESD/EX-D100
Right: FX2-Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-Black-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ESD/EX-D100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 9 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 10 1/26/2018
BenchTop Extraction Arm FX2 75 ESD/EX
Ceiling mounting example:FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-FX2-Duct connector-ESD/EX-D100-FX-Ceiling cover plate
Other mounting examples:Left: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
Right: Floor mounting with FX2-Up-Low arm and following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 11 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EXThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with two or three adjustable, composite friction joints.Offering strength and durability combined with easy handling, theycan be used in many types of environment. They are especiallysuitable for applications where small, flexible and easy-to-use armsare required.The arm is designed for use in electronic environments where thereis a risk of electrostatic discharges. The ESD/EX can also be usedfor certain applications in potentially explosive atmospheres.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX2100 ESD/EX
Noise level (dB(A)) 62 dB(A) at 450 m3/hInstallation IndoorMaterial Tubes in anodized aluminium.
Joints in conductive PP plastic.Duct connector in conductiveEPDM rubber.Minihood in conductive PPplastic.
Fume temperature max 70°CExtraction arm diameter (mm) 100Airflow (m3/h) 200 - 450Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 1 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
Image Description Weight (kg) Model
FX2-ESD/EX-D100-L1200-Up/Down-Low 4,8 70606544
FX2-ESD/EX-D100-L1200-Up/Down-Thru 4,1 70606744
FX2-ESD/EX-D100-L1800-Up-Low 5,9 70606844
FX2-ESD/EX-D100-L1800-Down-Low 5,9 70607044
FX2-ESD/EX-D100-L1800-Down-Through 5,2 70607144
FX2-ESD/EX-D100-L2400-Up-Low 6,9 70607244
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 2 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX2-Wall BRKT kit-Flat-L190-Black.Complete mounting kit, with flat wall bracke,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250 mm (9.84 inch) from thevertical centre line of the arm to the wall.
70377044
FX-Dome hood-ESD/EX-D50/75/100.Black dome hood, made of conductive ABS plastic,is designed to capture high dispersioncontaminants, which is explosive or has a risk of electrostatic discharges. It can beattached directly on minihood, irrespective of arm size. The ergonomics of handle designon both sides of the hood make it easier to maneuver.
70376983
FX-Combi hood-ESD/EX-D50/75/100.Black combi hood, made of conductive ABS plastic, is designed to capture low energycontamiants which is explosive or has a risk of electrostatic discharges. It can beattached directly on minihood, irrespective of arm size.The ergonomics of handle designon both sides of the hood make it easier to maneuver.
70500244
FX-Metal hood-ESD/EX-D50/75/100.ESD conductive black metal hood, made of anodized aluminum, is designed to capturecontamiants in high temperature, aggressive fume where corrosion resistance must beassured or explosive dust splatter. It can be attached directly on minihood, irrespective ofarm size.
70500544
FX-Flange hood-ESD/EX-D50/75/100.Black flange hood, made of conductive ABS plastic, is designed to maximize the capturezone without hinder objects on the bench or the user. It can be attached directly onminihood, irrespective of arm size.
70502944
FX2-Duct connector-ESD/EX-D100.Conductive black duct connector to ease the coupling of 100mm (4 inch) Alu duct toexternal 125mm (5 inch) ductwork. Please note all arms are already supplied with a ductconnector as standard.
70377041
FX2-Al duct-L1000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 1000 mm (39.37 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377058
FX2-Al duct-L2000-D75/100toD100.Aluminum duct with 100 mm (4 inch) diameter and 2000 mm (78.74 inch) length isdesigned to replace vertical ventilation duct above the swivel of FX2 75/100 arm. This is agood looking alternative to standard, ventilation duct.
70377059
FX-Hose-ESD-D100-L3000-Black-Flexible hose in black conductive PE with 100 mm (4 inch) diameter and 3000 mm(118.11 inch) length. It shall be used with hose support ring to connect hose to arm.
70377102
FX-Hose-ESD-D125-L5000-Black-Flexible hose in black conductive PE with 125 mm (5 inch) diameter and 5000 mm(195.85 inch) length. It shall be used with hose support ring to connect hose to arm.
70377103
FX2-Hose support ring-D100.Place into the 100 mm (4 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377068
FX2-Hose support ring-D125.Place into the 125 mm ( 5 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377069
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 3 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 4 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
Material:1) Flange: Conductive PP plastic
2) Tubes: Aluminum, anodized 10 µm
3) Damper adjustment handle: Aluminum: anodized 10 µm Internal spring: Stainless steel Damper blade: Conductive TP & PP plastic
4) Joints conductive: PP plastic with glass fibre reinforcement Plastic rings conductive: PP plastic with glass fibre reinforcement Axial locking rings conductive: PP plastic with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: conductive EPDM Rubber
6) Swivel: Aluminum, conductive powder coating Rivets: Aluminum Bearings swivel condutive: PP plastic with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 5 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
• FX2-ESD/EX-D100-L1200-Up/Down-LowPart number: 70606544Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-ESD/EX-D100-L1800-Down-LowPart number: 70607044Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 6 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
• FX2-ESD/EX-D100-L1200-Up/Down-ThruPart number: 70606744Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-ESD/EX-D100-L1800-Down-ThroughPart number: 70607144Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 7 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
• FX2-ESD/EX-D100-L1200-Up/Down-LowPart number: 70606544Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-ESD/EX-D100-L1800-Up-LowPart number: 70606844Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
*• FX2-ESD/EX-D100-L2400-Up-LowPart number: 70607244Max. working radius: 2290 (90,16 in)A: 1010 mm (39,7 in)B: 1010 mm (39,7 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 8 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
Wall mounting examples:Left: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ESD/EX-D100
Right: FX2-Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-Black-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-FX2-Duct connector-ESD/EX-D100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 9 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 10 1/26/2018
BenchTop Extraction Arm FX2 100 ESD/EX
Ceiling mounting example:FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-FX2-Duct connector-ESD/EX-D100-FX-Ceiling cover plate
Other mounting examples:Left: Overbench cabinet mounting with FX2-Up/Down-Through arm
Middle: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
Right: Floor mounting with FX2-Up-Low arm and following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 11 1/26/2018
BenchTop Extraction Arm FX2 75 CHEMThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with three adjustable, composite friction joints. Offeringstrength and durability combined with easy handling, they can beused in many types of environment. They are especially suitable forapplications where small, flexible and easy-to-use arms arerequired.With the profiles made of anodized aluminum with a whiteelectrophoretic deposition coating, the arm is ideal for fumeextraction in aggressive environments where corrosion resistancemust be assured.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX275 CHEM
Noise level (dB(A)) 58 dB(A) at 240 m3/hInstallation IndoorMaterial Tubes in anodized aluminium
with a white electrophoreticdeposition coating.Joints in PP plastic.Duct connector in EPDM rubber.Minihood in PP plastic.
Fume temperature max 70°CExtraction arm diameter (mm) 75Airflow (m3/h) 110 - 240Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 1 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Image Description Weight (kg) Model
FX2-CHEM-D75-L1100-Up-Low 3,2 70603144
FX2-CHEM-D75-L1100-Up-PLUS 4,5 70603244
FX2-CHEM-D75-L1100-Down-Low 3,2 70603344
FX2-CHEM-D75-L1100-Down-Through 2,6 70603444
FX2-CHEM-D75-L1500-Up-Low 3,4 70603544
FX2-CHEM-D75-L1500-Up-PLUS 4,7 70603644
FX2-CHEM-D75-L1500-Down-Low 3,4 70603744
FX2-CHEM-D75-L1500-Down-Through 2,8 70603844
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 2 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Wall BRKT kit-Flat-L190-White.Complete mounting kit, with flat wall bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall.
70377043
FX2-Wall-P BRKT kit-D50/75/100-L190.Complete mounting kit for mounting FX2 50/75/100 plus arms with 250 mm (9.84 inch)from the vertical centre line of the arm to the wall.
70377046
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX-Combi hood-CHEM-D50/75/100.Corrosion resistant combi dome hood, made of PE, for FX2 50/75/100 arms is designedto capture capture low energy and aggreesive contaminants . The ergonomics of handledesign on both sides of the hood make it easier to maneuver.
70500344
FX-Dome hood-CHEM-D50/75/100.Corrosion resistant white dome hood, made of PE plastic, is designed to capture highdispersion and aggreesive contaminants. It can be attached directly on minihood,irrespective of arm size. The ergonomics of handle design on both sides of the hoodmake it easier to maneuver.
70376984
FX-Metal hood-ORIG/CHEM-D50/75/100.Powder coated white metal hood, made of aluminum, is designed to capturecontaminants in high temperature, aggressive fume where corrosion resistance must beassured or dust splatter. It can be attached directly on minihood, irrespective of arm size.
70500444
FX-Flange hood-CHEM-D50/75/100.Corrosion resistant white flange hood, made of PE plastic, is designed to maximize thecapture zone without hinder objects on the bench or the user. It can be attached directlyon minihood, irrespective of arm size.
70503044
FX2-Duct connector-ORIG/CHEM-D100.Grey duct connector to ease the coupling of 100mm (4 inch) Alu duct to external 125mm(5 inch) ductwork. Please note all arms are already supplied with a duct connector asstandard.
70377040
FX2-Al duct-L1000-D75/100toD100-WHT.Corrosion resistant white duct with 100 mm (4 inch) diameter and 1000 mm (39.37 inch)length is designed to replace vertical ventilation duct above the swivel of FX2 75/100arms.The duct is made of anodized aluminum with a white electrophoretic deposition coatingwhich ensure good corrosion resistance. This is a good looking alternative to standard,ventilation duct.
70377054
FX2-Al duct-L2000-D75/100toD100-WHT. Corrosion resistant white duct with 100 mm (4inch) diameter and 2000 mm (78.74 inch) length is designed to replace vertical ventilationduct above the swivel of FX2 75/100 arms.The duct is made of anodized aluminum with a white electrophoretic deposition coatingwhich ensure good corrosion resistance.This is a good looking alternative to standard,ventilation duct.
70377055
FX-Hose-D75-L3000-Grey-Flexible hose in grey PVC with 75 mm (3 inch) diameter and 3000 mm (118.11 inch)length. It shall be used with hose support ring to connect hose to arm.
70377098
FX-Hose-D100-L3000-Grey-Flexible hose in grey PVC with 100 mm (4 inch) diameter and 3000 mm (118.11 inch)length. It shall be used with hose support ring to connect hose to arm.
70377099
FX2-Hose support ring-D75.Place into the 75 mm (3 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377067
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 3 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Accessory Part No
FX2-Hose support ring-D100.Place into the 100 mm (4 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377068
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 4 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 5 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Material:1) Flange: PP
2) Tubes: Aluminum: anodized 10 µm, with white electrophoretic deposition coating
3) Damper adjustment handle: Aluminum: anodized 10 µm Internal spring: Staineless steel Damper blade: Conductive TP & PP plastic
4) Joints: PP with glass fibre reinforcement Plastic rings: PP with glass fibre reinforcement Axial locking rings: PP with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: EPDM Rubber
6) Swivel: Aluminum, powder coating Rivets: Aluminum Bearings swivel: PP with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 6 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
• FX2-CHEM-D75-L1100-Up-PLUSPart number: 70603244Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-CHEM-D75-L1500-Up-PLUSPart number: 70603644Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 7 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
• FX2-CHEM-D75-L1100-Down-LowPart number: 70603344Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-CHEM-D75-L1500-Down-LowPart number: 70603744Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 8 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
• FX2-CHEM-D75-L1100-Down-ThroughPart number: 70603444Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-CHEM-D75-L1500-Down-ThroughPart number: 70603844Max. working radiD2:D5us: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 9 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
• FX2-CHEM-D75-L1100-Up-LowPart number: 70603144Max. working radius: 1090 mm (42,9 in)A: 420 mm (16,5 in)B: 420 mm (16,5 in)
• FX2-CHEM-D75-L1500-Up-LowPart number: 70603544Max. working radius: 1450 mm (57,1 in)A: 500 mm (19,7 in)B: 700 mm (27,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 10 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Ceiling mounting example:Left: FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-WHT-FX2-Duct connector-ORIG/CHEM-D100-FX-Ceiling cover plate
Right: FX2-Up-PLUS arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS
Other mounting examples:Left: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
Right: Floor mounting with FX2-Up-Low arm and following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 11 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Wall mounting examples:Left: FX2-Up-PLUS arm with following accessories:-FX2-Wall-P BRKT kit-D50/75/100-L190-FX2-Ceiling cover plate-PLUS
Middle: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-WHT-FX2-Duct connector-ORIG/CHEM-D100
Right: FX2-Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-White-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-WHT-FX2-Duct connector-ORIG/CHEM-D100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 12 1/26/2018
BenchTop Extraction Arm FX2 75 CHEM
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 13 1/26/2018
BenchTop Extraction Arm FX2 100 CHEMThe best and most cost-efficient solution for extraction of hazardous airborne contaminants,in applications where small, flexible and easy-to-use arms are required.
Nederman FX2 arms are made of lightweight anodized aluminiumsections, with three adjustable, composite friction joints. Offeringstrength and durability combined with easy handling, they can beused in many types of environment. They are especially suitable forapplications where small, flexible and easy-to-use arms arerequired.With the profiles made of anodized aluminum with a whiteelectrophoretic deposition coating, the arm is ideal for fumeextraction in aggressive environments where corrosion resistancemust be assured.
• Optimal efficiency and low noise provides safe and quietworking environment
• Ceilings, walls and floors or fixed to worktops mountings andcut2fit extension profile gives maximum installation flexibility
• The two outermost arm joints can rotate and swivel through360°, which gives the unique maneuverability
• The lean, smooth and aesthetic design allows arms to fit in wellin any environment without compromising its durability andreliability
• Highly integrated products that save customers’ time and costs,as well as providing the reliability and functionality to deliver abetter performance
Product name BenchTop Extraction Arm FX2100 CHEM
Noise level (dB(A)) 62 dB(A) at 450 m3/hInstallation IndoorMaterial Tubes in anodized aluminium
with a white electrophoreticdeposition coating.Joints in PP plastic.Duct connector in EPDM rubber.Minihood in PP plastic.
Fume temperature max 70°CExtraction arm diameter (mm) 100Airflow (m3/h) 200 - 450Arm length (m)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 1 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Image Description Weight (kg) Model
FX2-CHEM-D100-L1200-Up/Down-Low 4,8 70605644
FX2-CHEM-D100-L1200-Up-PLUS 5,9 70605744
FX2-CHEM-D100-L1200-Up/Down-Through 4,1 70605844
FX2-CHEM-D100-L1800-Up-Low 5,9 70605944
FX2-CHEM-D100-L1800-Up-PLUS 7,7 70606044
FX2-CHEM-D100-L1800-Down-Low 5,9 70606144
FX2-CHEM-D100-L1800-Down-Through 5,9 70606244
FX2-CHEM-D100-L2400-Up-Low 6,9 70606344
FX2-CHEM-D100-L2400-Up-PLUS 8,7 70606444
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 2 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Accessory Part No
FX-Bracket kit-D50/75/100-L190.Complete mounting kit, with the classic bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall
70501144
FX2-Bracket kit-D50/75/100-L500.Complete mounting kit, with the classic bracket, 500mm (19.68 inch) extension profileand associated parts, for mounting FFX2 50/75/100 arms on the ceiling .
70377042
FX2-Wall BRKT kit-Flat-L190-White.Complete mounting kit, with flat wall bracket,190 mm (7.48 inch) extension profile andassociated parts, for mounting FX2 50/75/100 arms with 250mm from the vertical centreline of the arm to the wall.
70377043
FX2-Wall-P BRKT kit-D50/75/100-L190.Complete mounting kit for mounting FX2 50/75/100 plus arms with 250 mm (9.84 inch)from the vertical centre line of the arm to the wall.
70377046
FX2-Bench bracket kit-D50/75/100,Complete mounting kit for mounting FX2 50/75/100 arms on the bench edge. 70501444
FX-Classic bracket-D50/75/100.The classic bracket should be used together with Cut2fit extension profile for mountingFX2 50/75/100 arms on the ceiling, wall, floor or on top of other horizontal surface.
70501244
FX-Cut2fit extension-L1100.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70501344
FX-Cut2fit extension-L2200.Cut2fit extension could be cut at any length and should be assembled together with theclassic bracket for mounting FX2 50/75/100 arms on the ceiling or wall.
70374600
FX-Ceiling cover plate.Cover false/dropped ceiling openings caused by both extension profile and ducting. 70502644
FX2-Ceiling cover plate-PLUS,Cover false/dropped ceiling opening caused by tube. 70377045
FX-Combi hood-CHEM-D50/75/100.Corrosion resistant combi dome hood, made of PE, for FX2 50/75/100 arms is designedto capture capture low energy and aggreesive contaminants . The ergonomics of handledesign on both sides of the hood make it easier to maneuver.
70500344
FX-Dome hood-CHEM-D50/75/100.Corrosion resistant white dome hood, made of PE plastic, is designed to capture highdispersion and aggreesive contaminants. It can be attached directly on minihood,irrespective of arm size. The ergonomics of handle design on both sides of the hoodmake it easier to maneuver.
70376984
FX-Metal hood-ORIG/CHEM-D50/75/100.Powder coated white metal hood, made of aluminum, is designed to capturecontaminants in high temperature, aggressive fume where corrosion resistance must beassured or dust splatter. It can be attached directly on minihood, irrespective of arm size.
70500444
FX-Flange hood-CHEM-D50/75/100.Corrosion resistant white flange hood, made of PE plastic, is designed to maximize thecapture zone without hinder objects on the bench or the user. It can be attached directlyon minihood, irrespective of arm size.
70503044
FX2-Duct connector-ORIG/CHEM-D100.Grey duct connector to ease the coupling of 100mm (4 inch) Alu duct to external 125mm(5 inch) ductwork. Please note all arms are already supplied with a duct connector asstandard.
70377040
FX2-Al duct-L1000-D75/100toD100-WHT.Corrosion resistant white duct with 100 mm (4 inch) diameter and 1000 mm (39.37 inch)length is designed to replace vertical ventilation duct above the swivel of FX2 75/100arms.The duct is made of anodized aluminum with a white electrophoretic deposition coatingwhich ensure good corrosion resistance. This is a good looking alternative to standard,ventilation duct.
70377054
FX2-Al duct-L2000-D75/100toD100-WHT. Corrosion resistant white duct with 100 mm (4inch) diameter and 2000 mm (78.74 inch) length is designed to replace vertical ventilationduct above the swivel of FX2 75/100 arms.The duct is made of anodized aluminum with a white electrophoretic deposition coatingwhich ensure good corrosion resistance.This is a good looking alternative to standard,ventilation duct.
70377055
FX-Hose-D100-L3000-Grey-Flexible hose in grey PVC with 100 mm (4 inch) diameter and 3000 mm (118.11 inch)length. It shall be used with hose support ring to connect hose to arm.
70377099
FX-Hose D125-L5000-Grey-Flexible hose in grey PVC with 125 mm (5 inch) diameter and 5000 mm (195.85 inch)length. It shall be used with hose support ring to connect hose to arm.
70377100
FX2-Hose support ring-D100.Place into the 100 mm (4 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377068
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 3 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Accessory Part No
FX2-Hose support ring-D125.Place into the 125 mm ( 5 inch) hose to support the connection between the hose and theduct connector of the arm. A must to connect the hose to arm.
70377069
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 4 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Sound Level diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Sound Pressure Level (dB) (A))
Pressure Drop diagram:1) X- Axis: Air Flow Rate (cfm)2) X- Axis: Air Flow Rate (m/h)
3) Y-Axis: Static Pressure Drop (Pa)4) Y-Axis: Static Pressure Drop (in. wg.)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 5 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Material:1) Flange: PP
2) Tubes: Aluminum: anodized 10 µm, with white electrophoretic deposition coating
3) Damper adjustment handle: Aluminum: anodized 10 µm Internal spring: Staineless steel Damper blade: Conductive TP & PP plastic
4) Joints: PP with glass fibre reinforcement Plastic rings: PP with glass fibre reinforcement Axial locking rings: PP with glass fibre reinforcement Adjustment knobs: PA & EDS plastic Threaded shaft inside joints: Stainless Steel
5) Duct connector: EPDM Rubber
6) Swivel: Aluminum, powder coating Rivets: Aluminum Bearings swivel: PP with glass fibre reinforcement
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 6 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
• FX2-CHEM-D100-L1200-Up/Down-LowPart number: 70605644Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-CHEM-D100-L1800-Down-LowPart number: 70606144Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 7 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
• FX2-CHEM-D100-L1200-Up/Down-ThroughPart number: 70605844Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-CHEM-D100-L1800-Down-ThroughPart number: 70606244Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 8 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
• FX2-CHEM-D100-L1200-Up/Down-LowPart number: 70605644Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-CHEM-D100-L1800-Up-LowPart number: 70605944Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
• FX2-CHEM-D100-L2400-Up-LowPart number: 70606344Max. working radius: 2290 mm (90,2 in)A: 1010 mm (39,7 in)B: 1010 mm (39,7 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 9 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
• FX2-CHEM-D100-L1200-Up-PLUSPart number: 70605744Max. working radius: 1170 mm (46,1 in)A: 450 mm (17,7 in)B: 450 mm (17,7 in)
• FX2-CHEM-D100-L1800-Up-PLUSPart number: 70606044Max. working radius: 1770 mm (69,7 in)A: 750 mm (29,5 in)B: 750 mm (29,5 in)
• FX2-CHEM-D100-L2400-Up-PLUSPart number: 70606444Max. working radius: 2290 mm (90,2 in)A: 1010 mm (39,7 in)B: 1010 mm (39,7 in)
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 10 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Wall mounting examples:Left: FX2-Up-PLUS arm with following accessories:-FX2-Wall-P BRKT kit-D50/75/100-L190-FX2-Ceiling cover plate-PLUS
Middle: FX2-Up-Low arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-WHT-FX2-Duct connector-ORIG/CHEM-D100
Right: FX2-Up-Low arm with following accessories:-FX2-Wall BRKT kit-Flat-L190-White-FX2-Ceiling cover plate-PLUS-FX2-Alu duct-WHT-FX2-Duct connector-ORIG/CHEM-D100
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 11 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Bench mounting examples:Left: FX2-Down-Low arm with following accessories:-FX2-Bench bracket kit-D50/75/100
Right: FX2-Down-Through arm
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 12 1/26/2018
BenchTop Extraction Arm FX2 100 CHEM
Ceiling mounting example:Left: FX2-Up-Low arm with following accessories:-FX-Classic bracket-FX-Cut2fit extension-L1100-FX2-Alu duct-WHT-FX2-Duct connector-ORIG/CHEM-D100-FX-Ceiling cover plate
Right: FX2-Up-PLUS arm with following accessories:-FX2-Bracket kit-D50/75/100-L500-FX2-Ceiling cover plate-PLUS
Other mounting examples:Left: Overbench cabinet mounting with FX2-Up/Down-Through arm
Middle: Shelf mounting with FX2-Up-Low arm and following accessories:-FX2-Bench bracket kit
This content is protected under copyright law, furnished for informational use only, and subject to change without notice. © Nederman Holding AB
www.nederman.com 13 1/26/2018
nederman.com
Nederman is a world-leading environmental technology company. We filter, clean and recycle to create eco-efficient production in demanding industrial surroundings.
For more than 70 years, Nederman has developed, manufactured, and installed products and solutions to reduce the strain on the environment and improve working conditions in numerous industries. Our products and systems have been ground-breaking in industries such as machining, metal fabrication, mining, auto motive, composite manufacturing, food, pharmaceuticals, wood-working, and many others.