Amipox at Asl

5/19/2018 Amipox at Asl

1/8

AMIPOX GRE Fiberglass SystemsSeries AT - ASL - AP


2/8

Performance

Hydrostatic Design Basis

The pipe wall design uses a 122 MPa (17.600 psi)HDB with a 0.5-service factor for static design

(ASTM D-2992 Procedure B). The laminate meets

the requirements of API 15LR Specification, ANSI/

AWWA-C950 and ISO Standard. Classification as per

ASTM D-2310 / ASTM D-2996: RTRP-11FW (Static).

Design Pressure

The series are designed for the following pressure

ratings:

AT series up to 100 bar (1450 psi)

ASL series up to 70 bar (1015 psi)

AP series up to 20* bar (290 psi)

* for higher pressure, consult Amipox Engineering

The systems are designed to provide a minimal 3:1

safety factor in accordance with ASTM D-1599.

Maximum Operating Temperature

The maximum operating temperature is 120C (250F).Between 90C and 120C values must be degraded

linearly. For detailed specifications please contact us.

Pipe Description

Amipox GRE pipe Series AT, ASL and AP are produced

by a filament winding process. These pipes are RTR

(Reinforced Thermosetting Resin). The pipe structural

wall consists of continuous glass fibers (E-glass) wound

at a 54 2 helical angle in a matrix of amine-cured

epoxy resin. The resin-rich liner 0.5 mm (20 mills)consists of C-glass (C-veil) and the same resin system

as used in the pipe wall. Conductive pipes can be

produced on request.

Fittings

Amipox fittings are either filament-wound or mitered

made of segments. They are made from the same glass

and resin materials as the pipe.

Uses and Applications

Brackish water

Brine

Crude oil transmission

Electrical conduits

Fire fighting systems

Oilfield injection

Potable water

Saltwater and seawater

Sewage, draining systems

General Industrial Services for corrosive liquides

Other applications on request

2


3/8

Pipe Properties

Dimensions

Our Amipox GRE Pipes Series AT, ASL and APare produced from DN 80 (3) up to DN 1200 (48).

The standard random length supplied is 9 m (30 ft) for

DN 80 up to DN 600 and 12 m (40 ft) for DN 200 up to

DN 1200.

Conversions

1 bar = 105Pa = 14.5 Psi = 1.02 kg/cm2

1 MPa = 1 N/mm2 = 145 Psi = 10.2 kg/cm2

1 inch = 25.4 mm

1 lb.in = 0.113 Nm

1 Btu (int.)

in/hr.sqft.F = 0.1442 W (mK)

Thermal Conductivity 0.33 W/(mK)

(ASTM C-177)

Thermal linear Expansion 18.0x10-6mm/mm C

(ASTM D-696)

Flow Coefficient 150

(Hazen-Williams)

Absolute Roughness 5.3x10-6m

Density 1.8 g/cm3

Physical properties

Method Value Value Unit

at 21C at 93C

Bi-Axial

Hoop stress at weeping ASTM D-1599 200 - N/mm2

Circumferential

Hoop tensile stress ASTM D-2290 220 - N/mm2

Hooptensile modulus ASTM D-2290 25200 22100 N/mm

2

Poissons ratio: axial/hoop 0.56 0.70

Longitudinal

Axial tensile strength ASTM D-2105 80.0 65 N/mm2

Tensile modulus ASTM D-2105 12500 9700 N/mm2

Poissons ratio: hoop/axial ASTM D-2105 0.37 0.41

Axial bending strength 85 - N/mm2

Beam

Apparent elastic modulus ASTM D-2925 12500 8000 N/mm2

Hydrostatic Design Basis

Static HDB ASTM D-2992 - 122* (20 years) N/mm2

procedure B 114* (50 years)

* at 65C (150F)

Mechanical properties

3


4/8

Wall Thickness

Empty Pipe Weight

Filled Pipe Weight

4

Nominalsize

IDMinimum wall thickness in mm

Pressure class (bar)

mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 2.5 2.5 2.5 2.5 2.5 2.5 2.7 3.2 3.9 4.7 5.4

100 4 100 2.5 2.5 2.5 2.5 2.5 2.6 3.2 3.9 4.8 5.7 6.6

150 6 150 2.5 2.5 2.5 2.5 3.0 3.6 4.6 5.6 6.9 8.3 9.7

200 8 200 2.5 2.5 2.5 3.2 3.8 4.7 5.9 7.3 9.1 10.9 12.7

250 10 250 2.5 3.0 3.4 3.8 4.7 5.7 7.3 9.0 11.2 13.5 15.8

300 12 300 3.0 3.5 4.0 4.5 5.5 6.8 8.6 10.7 13.4 16.1 18.8

350 14 350 3.4 4.0 4.6 5.2 6.4 7.8 10.0 12.4 15.5 18.7 21.9400 16 400 3.8 4.5 5.2 5.8 7.2 8.9 11.3 14.1 17.7

450 18 450 4.2 5.0 5.7 6.5 8.0 9.9 12.7 15.8 19.8

500 20 500 4.6 5.5 6.3 7.2 8.9 11.0 14.0 17.5

600 24 600 5.5 6.5 7.5 8.5 10.5 13.1 16.7 20.9

700 28 700 6.3 7.5 8.7 9.8 12.2 15.2 19.4

750 30 750 6.7 8.0 9.2 10.5 13.0 16.2 20.8

800 32 800 7.1 8.5 9.8 11.2 13.9 17.3 22.1

900 36 900 8.0 9.5 11.0 12.5 15.6 19.4 24.8

1000 40 1000 8.8 10.5 12.1 13.8 17.2 21.5 27.5

1050 42 1050 9.2 11.0 12.7 14.5 18.1 22.5

1100 44 1100 9.6 11.5 13.3 15.2 18.9 23.6

1200 48 1200 10.5 12.5 14.5 16.5 20.6 25.7

Indicated wall thickness includes 0.5 mm liner.

Nominalsize

IDApproximate weight of pipe excluding joints in kg/m


mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.4 1.8 2.2 2.5

100 4 100 1.7 1.7 1.7 1.7 1.7 1.7 1.8 2.2 2.7 3.3 3.9

150 6 150 2.5 2.5 2.5 2.5 2.5 3.0 3.8 4.8 6.0 7.3 8.6

200 8 200 3.3 3.3 3.3 3.4 4.2 5.2 6.7 8.4 10.5 12.8 15.1

250 10 250 4.1 4.1 4.7 5.3 6.5 8.1 10.3 13.0 16.3 19.8 23.5300 12 300 4.9 5.7 6.6 7.5 9.2 11.5 14.7 18.5 23.4 28.4 33.7

350 14 350 6.5 7.7 8.8 10.0 12.5 15.5 19.9 25.1 31.7 38.6 45.7

400 16 400 8.3 9.9 11.4 13.0 16.2 20.2 25.9 32.7 41.3

450 18 450 10.4 12.4 14.4 16.4 20.4 25.4 32.7 41.2 52.2

500 20 500 12.8 15.2 17.6 20.1 25.0 31.3 40.3 50.8

600 24 600 18.2 21.7 25.2 28.7 35.8 44.8 57.7 72.8

700 28 700 24.5 29.3 34.0 38.8 48.5 60.8 78.3

750 30 750 28.0 33.5 38.9 44.4 55.6 69.7 89.8

800 32 800 31.8 38.0 44.2 50.5 63.1 79.2 102.1

900 36 900 40.0 47.9 55.7 63.7 79.7 100.0 129.0

1000 40 1000 49.2 58.9 68.6 78.4 98.1 123.2 159.0

1050 42 1050 54.2 64.8 75.5 86.3 108.1 135.7

1100 44 1100 59.3 71.0 82.8 94.6 118.5 148.8

1200 48 1200 70.4 84.3 98.3 112.4 140.8 176.9

Nominalsize

IDFilled pipe weight (kg/m), fluid density (1000 kg/m3)


mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 6.4 6.4 6.4 6.4 6.4 6.4 6.4 6.5 6.8 7.2 7.6

100 4 100 9.5 9.5 9.5 9.5 9.5 9.5 9.6 10.1 10.6 11.2 11.7

150 6 150 20.1 20.1 20.1 20.1 20.1 20.7 21.5 22.5 23.7 24.9 26.3

200 8 200 34.7 34.7 34.7 34.9 35.7 36.7 38.1 39.8 42.0 44.2 46.5

250 10 250 53.1 53.1 53.7 54.4 55.6 57.2 59.4 62.0 65.4 68.9 72.6

300 12 300 75.5 76.4 77.3 78.2 79.9 82.2 85.4 89.2 94.1 99.1 104.3

350 14 350 102.7 103.9 105.1 106.3 108.7 111.8 116.2 121.3 127.9 134.8 141.9

400 16 400 134.0 135.5 137.1 138.7 141.8 145.9 151.6 158.3 167.0

450 18 450 169.5 171.4 173.4 175.4 179.4 184.5 191.7 200.3 211.2

500 20 500 209.1 211.6 214.0 216.4 221.4 227.7 236.6 247.1

600 24 600 300.9 304.4 307.9 311.4 318.5 327.6 340.5 355.6

700 28 700 409.4 414.1 418.9 423.7 433.3 445.6 463.2

750 30 750 469.8 475.3 480.7 486.2 497.4 511.5 531.6800 32 800 534.5 540.6 546.9 553.1 565.8 581.8 604.7

900 36 900 676.2 684.0 691.9 699.8 715.8 736.1 765.1

1000 40 1000 834.6 844.3 854.0 863.8 883.5 908.6 944.4

1050 42 1050 920.1 930.7 941.4 952.2 974.0 1 ,001.6

1100 44 1100 1,009.7 1,021.3 1,033.1 1,044.9 1,068.8 1,099.2

1200 48 1200 1,201.4 1,215.3 1,229.3 1,243.3 1,271.8 1,307.9


5/8

External Pressure Performance

Surge Pressure

The maximum allowable surge pressure is 1.5 times the

rated pressure.

Field Testing

The pipe system is designed for field testing with waterat 1.5 times the rated design pressure.

5

Nominalsize

IDAllowable collapse pressure (bar) at 21C


mm in mm 10 12 14 16 20 25 32 40 50 60 7080 3 80 19.40 19.40 19.40 19.40 19.40 19.40 19.40 25.02 50.13 88.89 144.88

100 4 100 9.93 9.93 9.93 9.93 9.93 9.93 12.55 25.02 50.13 88.89 144.88

150 6 150 2.94 2.94 2.94 2.94 2.97 5.88 12.55 25.02 50.13 88.89 144.88

200 8 200 1.24 1.24 1.24 1.51 2.97 5.88 12.55 25.02 50.13 88.89 144.88

250 10 250 0.64 0.64 1.00 1.51 2.97 5.88 12.55 25.02 50.13 88.89 144.88

300 12 300 0.37 0.63 1.00 1.51 2.97 5.88 12.55 25.02 50.13 88.89 144.88

350 14 350 0.36 0.63 1.00 1.51 2.97 5.88 12.55 25.02 50.13 88.89 144.88

400 16 400 0.36 0.63 1.00 1.51 2.97 5.88 12.55 25.02 50.13

450 18 450 0.36 0.63 1.00 1.51 2.97 5.88 12.55 25.02 50.13

500 20 500 0.36 0.63 1.00 1.51 2.97 5.88 12.55 25.02

600 24 600 0.36 0.63 1.00 1.51 2.97 5.88 12.55 25.02

700 28 700 0.36 0.63 1.00 1.51 2.97 5.88 12.55

750 30 750 0.36 0.63 1.00 1.51 2.97 5.88 12.55

800 32 800 0.36 0.63 1.00 1.51 2.97 5.88 12.55

900 36 900 0.36 0.63 1.00 1.51 2.97 5.88 12.55

1000 40 1000 0.36 0.63 1.00 1.51 2.97 5.88 12.551050 42 1050 0.36 0.63 1.00 1.51 2.97 5.88

1100 44 1100 0.36 0.63 1.00 1.51 2.97 5.88

1200 48 1200 0.36 0.63 1.00 1.51 2.97 5.88

Pressure ratings at 21C. Use 70% of the above values for industrial applications and 30% for marine applications.

Stiffness Factor (SF)

Nominalsize

IDSF per ASTM D-2412 in Nm at 21C


mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 32.8 32.8 32.8 32.8 32.8 32.8 41.3 70.2 127.5 211.5 328.2

100 4 100 32.8 32.8 32.8 32.8 32.8 36.9 69.0 124.7 230.5 386.9 606.0

150 6 150 32.8 32.8 32.8 32.8 57.2 102.0 198.3 369.2 699.6 1,194.5 1,894.4

200 8 200 32.8 32.8 32.8 66.7 119.3 217.8 432.5 817.8 1,570.2 2,705.1 4,318.3

250 10 250 32.8 56.7 83.4 118.3 215.3 398.7 802.5 1,532.6 2,966.5 5,139.0 8,236.8

300 12 300 56.7 89.3 133.8 191.4 352.6 659.5 1,339.5 2,575.5 5,012.8 8,716.5 14,008.7

350 14 350 82.5 133.2 201.3 289.6 538.4 1,014.6 2,074.6 4,008.5 7,833.1 13,657.8 21,993.0

400 16 400 115.2 189.7 288.3 416.8 780.2 1,478.6 3,038.8 5,893.6 11,551.8

450 18 450 155.6 260.2 397.4 576.7 1,085.3 2,066.1 4,263.3 8,292.7 16,293.0

500 20 500 204.4 346.2 531.0 773.0 1,461.2 2,791.6 5,779.1 11,267.8

600 24 600 349.4 571.4 881.8 1,289.7 2,454.3 4,715.0 9,809.2 19,194.1

700 28 700 525.1 877.7 1,360.6 1,996.7 3,818.6 7,365.4 15,377.8

750 30 750 631.6 1,065.2 1,654.2 2,431.0 4,658.4 8,999.6 18,816.8

800 32 800 751.6 1,277.6 1,987.3 2,924.1 5,613.0 10,859.3 22,733.7

900 36 900 1,075.2 1,783.5 2,781.8 4,101.6 7,896.3 15,313.2 32,125.6

1000 40 1000 1,431.1 2,408.0 3,764.0 5,559.0 10,727.6 20,843.7 43,802.3

1050 42 1050 1,635.2 2,768.6 4,331.8 6,402.1 12,367.1 24,049.1

1100 44 1100 1,857.9 3,163.5 4,953.9 7,326.4 14,165.6 27,567.3

1200 48 1200 2,431.0 4,062.4 6,371.3 9,433.5 18,269.4 35,600.5

Pipe Stiffness (PS)Nominal

sizeID

PS per ASTM D-2412 in bar 21C


mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 31.37 31.37 31.37 31.37 31.37 31.37 39.24 65.38 115.80 187.15 283.07

100 4 100 16.36 16.36 16.36 16.36 16.36 18.35 33.70 59.69 107.57 175.96 268.54

150 6 150 4.97 4.97 4.97 4.97 8.57 15.10 28.85 52.62 97.19 161.72 249.90

200 8 200 2.12 2.12 2.12 4.27 7.56 13.63 26.60 49.29 92.24 154.87 240.89

250 10 250 1.09 1.88 2.75 3.88 7.00 12.80 25.31 47.36 89.36 150.86 235.58

300 12 300 1.09 1.71 2.56 3.64 6.64 12.26 24.47 46.10 87.46 148.22 232.08

350 14 350 1.00 1.61 2.42 3.47 6.39 11.89 23.88 45.22 86.13 146.35 229.61

400 16 400 0.94 1.54 2.33 3.35 6.20 11.61 23.45 44.56 85.13

450 18 450 0.89 1.48 2.25 3.25 6.06 11.40 23.11 44.05 84.37

500 20 500 0.85 1.44 2.20 3.18 5.95 11.23 22.85 43.65

600 24 600 0.85 1.38 2.11 3.07 5.79 10.99 22.45 43.05

700 28 700 0.80 1.33 2.05 3.00 5.68 10.81 22.17

750 30 750 0.78 1.31 2.03 2.97 5.63 10.74 22.06800 32 800 0.77 1.30 2.01 2.94 5.59 10.68 21.97

900 36 900 0.77 1.27 1.98 2.90 5.52 10.58 21.81

1000 40 1000 0.75 1.25 1.95 2.86 5.47 10.50 21.68

1050 42 1050 0.74 1.24 1.94 2.85 5.45 10.47

1100 44 1100 0.73 1.24 1.93 2.84 5.43 10.43

1200 48 1200 0.74 1.22 1.91 2.81 5.39 10.38


6/8

Specific Tangential Stiffness (STIS)

6

Bending RadiusNominal

sizeID

Minimum allowable bending radius in meter 21C and standard pressure rating


mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 14.45 15.18 15.99 16.89 19.04 22.63 30.82 41.27 41.62 41.98 42.34

100 4 100 19.07 20.36 21.85 23.56 27.95 36.48 51.17 51.52 51.96 52.41 52.86

150 6 150 33.58 37.81 43.26 50.55 75.87 76.19 76.64 77.16 77.82 78.49 79.17

200 8 200 54.61 66.76 85.87 100.74 101.08 101.50 102.10 102.79 103.67 104.57 105.48

250 10 250 87.83 124.43 125.66 125.87 126.29 126.82 127.57 128.43 129.53 130.65 131.79

300 12 300 148.41 150.49 150.74 150.99 151.50 152.13 153.03 154.07 155.39 156.73 158.09

350 14 350 175.24 175.53 175.82 176.12 176.70 177.44 178.49 179.70 181.24 182.81 184.40

400 16 400 200.23 200.57 200.91 201.24 201.91 202.76 203.96 205.34 207.10

450 18 450 225.22 225.61 225.99 226.36 227.12 228.07 229.42 230.98 232.96

500 20 500 250.21 250.65 251.07 251.49 252.33 253.39 254.88 256.61

600 24 600 300.25 300.73 301.23 301.74 302.74 304.01 305.81 307.89

700 28 700 350.23 350.81 351.40 351.98 353.16 354.64 356.74

750 30 750 375.22 375.86 376.48 377.11 378.37 379.96 382.20

800 32 800 400.21 400.90 401.56 402.23 403.58 405.27 407.66

900 36 900 450.25 450.98 451.73 452.48 453.99 455.90 458.59

1000 40 1000 500.23 501.06 501.89 502.73 504.41 506.52 509.52

1050 42 1050 525.22 526.10 526.97 527.85 529.62 531.84

1100 44 1100 550.21 551.14 552.06 552.98 554.82 557.15

1200 48 1200 600.25 601.22 602.22 603.22 605.24 607.78

Note:Do not bend the pipe until the adhesive is cured. Sharper bends may create excessive stress concentration.

Nominalsize

IDSTIS in N/m221C


mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 58,436 58,436 58,436 58,436 58,436 58,436 73,079 121,766 2 15,682 3 48,572 5 27,212

100 4 100 30,470 30,470 30,470 30,470 30,470 34,174 62,762 111,174 200,350 327,734 500,147

150 6 150 9,252 9,252 9,252 9,252 15,961 28,120 53,725 97,997 181,011 301,195 465,430

200 8 200 3,952 3,952 3,952 7,952 14,088 25,390 49,541 91,803 171,805 288,450 448,652

250 10 250 2,038 3,501 5,125 7,233 13,036 23,838 47,135 88,211 166,427 280,969 438,769

300 12 300 2,038 3,194 4,763 6,778 12,364 22,838 45,574 85,867 162,902 276,051 432,257

350 14 350 1,870 3,004 4,515 6,465 11,898 22,141 44,480 84,218 160,414 272,571 427,642400 16 400 1,750 2,866 4,335 6,236 11,557 21,628 43,671 82,994 158,564

450 18 450 1,660 2,762 4,198 6,062 11,295 21,234 43,048 82,050 157,134

500 20 500 1,591 2,681 4,091 5,925 11,089 20,922 42,554 81,300

600 24 600 1,574 2,562 3,933 5,724 10,785 20,460 41,819 80,183

700 28 700 1,490 2,479 3,823 5,583 10,570 20,134 41,300

750 30 750 1,458 2,446 3,780 5,527 10,485 20,004 41,093

800 32 800 1,430 2,418 3,742 5,478 10,412 19,892 40,913

900 36 900 1,436 2,371 3,680 5,398 10,289 19,704 40,614

1000 40 1000 1,394 2,334 3,630 5,335 10,192 19,556 40,375

1050 42 1050 1,376 2,318 3,609 5,307 10,150 19,492

1100 44 1100 1,360 2,304 3,590 5,283 10,113 19,434

1200 48 1200 1,371 2,279 3,557 5,240 10,047 19,334

Nominalsize

IDPartial span recommendations in meters 21C for horizontal support arrangement


mm in mm 10 12 14 16 20 25 32 40 50 60 70

80 3 80 4.22 4.22 4.22 4.22 4.22 4.22 4.22 4.29 4.47 4.64 4.78

100 4 100 4.49 4.49 4.49 4.49 4.49 4.49 4.55 4.75 4.97 5.16 5.32

150 6 150 5.00 5.00 5.00 5.00 5.01 5.23 5.50 5.76 6.04 6.27 6.48

200 8 200 5.40 5.40 5.40 5.47 5.72 5.99 6.31 6.62 6.94 7.22 7.46

250 10 250 5.72 5.72 5.90 6.06 6.36 6.66 7.03 7.38 7.74 8.05 8.32

300 12 300 6.00 6.22 6.42 6.61 6.93 7.28 7.68 8.06 8.47 8.81 9.11

350 14 350 6.44 6.69 6.91 7.11 7.46 7.84 8.28 8.69 9.13 9.50 9.83

400 16 400 6.85 7.12 7.36 7.58 7.96 8.36 8.83 9.28 9.75

450 18 450 7.24 7.53 7.79 8.02 8.43 8.86 9.36 9.84 10.34

500 20 500 7.61 7.92 8.19 8.44 8.87 9.32 9.86 10.36

600 24 600 8.30 8.64 8.94 9.22 9.69 10.20 10.78 11.34

700 28 700 8.93 9.31 9.64 9.93 10.45 11.00 11.63

750 30 750 9.23 9.62 9.96 10.27 10.81 11.38 12.04

800 32 800 9.52 9.93 10.28 10.60 11.16 11.75 12.43

900 36 900 10.08 10.51 10.89 11.23 11.83 12.45 13.17

1000 40 1000 10.61 11.07 11.47 11.83 12.46 13.11 13.88

1050 42 1050 10.87 11.33 11.75 12.12 12.76 13.431100 44 1100 11.12 11.59 12.02 12.40 13.05 13.75

1200 48 1200 11.60 12.10 12.54 12.94 13.63 14.35

Note:For continuous span, use the given values plus 20%. For simple span, use the given values minus 20%. The span recommendations are

based on pipes filled with water with a specific gravity of 1000 kg/m3, and include no provision for additional weights caused by valves, flanges,

or other heavy objects. The span recommendations are calculated for a maximum long-time deflection of 13 mm. (1/2-inch) to ensure good

appearance and adequate drainage.

Span lengths


7/8

Fittings

Filament-wound Fittings

Filament-wound fittings are made on steel moulds.Sizes available are from 80-600 mm (3-24). The wall

construction consists of a reinforcement structure

(which is made of a combination of E-glass materials

impregnated with amine-cured epoxy resin) and an

inner liner (C-veil glass impregnated with the same resin

system as the reinforcement structure).

Available range:

90 and 45 Elbows

Tees and Laterals

Tapered-Body Reducers

Reducer Bushings and Plugs

Plugs and Pipe Caps

Nipples

Saddles

Coupling

Flanges and Reducing Flanges

Laminated segmented Fittings

Laminated segmented fittings are available in sizes

from DN 80 mm up to DN 1,200 mm (3-48).

They are made out of GRE pipe segments which are

cut, fitted and laminated to the required shape.

Available range:

90 and 45 Elbows

Equal and Reducing Tees

Equal and Reducing Laterals

Other non standard fittings

Flanges

The range includes DN 80-1200 mm (3-48) flanged

fittings which are in accordance with ANSI B16.1 andB16.5 drilling class.

Other flange drilling patterns such as DIN, ISO and

JIS are available on request.

Flanges could be Standard, Heavy Duty or Van Stone

type with O ring or flat gasket.

Joining Systems

We offer various different

joining systems

The AT series with taper-taper joints

The ASL series with traditional mechanical seal lock,

with O ring and with locking key

The AP series with plain ends laminated joints

ASL Seal-Lock Joint Key and O Ring Sealing

ASL series Seal-lock-joint is a connection with an

O ring and a locking key; max. pressure rates 70 bar.

Butt-And-Wrap (or Lamination) joint

This joint for plain ends is used generally for field

adjustments and for large diameter pipes and in case

other types of joints are not available.

Butt & Wrap Joints are available for all sizes.

AT Adhesive Taper-Taper Joint

AT series, adhesive bonded taper-taper joint, max.

pressure rating 100 bar.

7


8/8

Utmost care has been taken to

ensure that all contents of this

brochure are accurate. However,AMIANTITand its subsidiaries do

not accept responsibility for any

problems which may arise as a

result of errors in this publication.

Therefore customers should make

inquiries into the potential product

supplier and convince themselves

of the suitability of any products

supplied or manufactured by

AMIANTITand/or its subsidiaries

before using them.

AP-F2V401-13-ENG

Distributed by:

AMIPOX

First Industrial City

P.O. Box 589

Dammam, 31421Saudi Arabia

Tel.: + 966 (3) 847 1500

Fax: + 966 92 000 4070

[email protected]

www.amiantit.com

Documents

Amipox at Asl