Upload
flipeside67
View
226
Download
0
Embed Size (px)
Citation preview
8/3/2019 Analysis of Sound Waves
1/33
Occupational Health & SafetyPractitioner
Reading
ANALYSIS OF SOUND WAVES
January 2009
8/3/2019 Analysis of Sound Waves
2/33
Contents
OVERVIEW.....................................................................................................................1
SECTION 1: INTRODUCTION.......................................................................................2
SECTION 2: DECIBELS.................................................................................................3
SECTION 3: TYPICAL SOUND PRESSURE LEVELS..................................................6
SECTION 4: RELATIONSHIP BETWEEN SOUND INTENSITY LEVEL, SOUNDPOWER LEVEL AND SOUND PRESSURE LEVEL.......................................................8
SECTION 5: ADDITION OF DECIBELS ......................................................................10
SECTION 6: SUBTRACTION OF DECIBELS..............................................................12
SECTION 7: FREQUENCY SPECTRUM OF A SOUND .............................................13
SECTION 8: FREQUENCY ANALYSIS .......................................................................15
SECTION 9: FREQUENCY WEIGHTING NETWORKS ..............................................18
APPENDICIES AND REVIEW EXERCISE ANSWERS................................................22
CONCLUSION ..............................................................................................................28
REFERENCES & FURTHER READING.......................................................................28
8/3/2019 Analysis of Sound Waves
3/33
8/3/2019 Analysis of Sound Waves
4/33
8/3/2019 Analysis of Sound Waves
5/33
READING ANALYSIS OF SOUND WAVES
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 1
OVERVIEW
This reading covers the analysis of sound waves and includes thedecibel scale, how to add and subtract decibels, sound spectra -octave and one-third octave frequency analysis, and A- and C-frequency weighting networks.
ObjectivesAfter reading this information you should be able to explain:
the decibel scale;
how to add and subtract decibels;
the terms sound power level, sound intensity level and soundpressure level and the relationship between them;
the relationship between sound pressure, sound intensity andsound power;
sound spectra - octave and one-third octave frequencyanalysis; and
A- and C- frequency weighting networks.
Pre-requisitesTo successfully undertake this reading learners need to:
have completed the reading on Basic Acoustics;
have an understanding of algebra (integration and logarithmic
functions); andhave access to a scientific calculator.
AuthorPamela Gunn B.Sc.(Hons Physics) University of Western AustraliaM.Sc.(Occupational Hygiene) London University
8/3/2019 Analysis of Sound Waves
6/33
READING ANALYSIS OF SOUND WAVES
Section 1: INTRODUCTION
In the first reading on Basic Acoustics you learnt about some of theterms used to describe sound waves. In this reading you will beintroduced to further terms we use in the measurement of themagnitude of sound waves and their frequency content.
Before you progress to actual measurement and assessment ofnoise, you need to understand the decibel scale of measurementand how to do decibel addition and subtraction .
For those of you not used to calculations, this may look a little
heavy going - but tables have been given to help you work throughthe examples. Give the mathematical option a try as, with the aidof a scientific calculator, you will find this method much quickeronce you get the hang of it.
Frequency analysis is another concept covered in the reading.This is an important area to understand, as many noise controlmeasures work to a different extent depending on the frequencycontent of the noise.
An explanation of A- and C- frequency weighting networks isalso given, along with exercises so that you can practice bothweighting and decibel addition.
PAGE 2 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
7/33
READING ANALYSIS OF SOUND WAVES
Section 2: DECIBELS
You have probably all heard of the term decibel (or dB for short)in connection with sound. We will now see how this relates to thequantities discussed in the first reading.
2.1 Large range of sound intensitiesThe human ear responds to sounds over a very large range ofsound intensities:
the sound intensity ofthe threshold ofhearing (the quietestsound we can hear) is0.00000000001watts/m 2 (often written10 -12 watts/m 2 );
whilst the sound intensityat the threshold of pain isabout 10 watts/m.
2.2 Decibel scale is used to cover therange of sound intensitiesTo handle this large range we make use of a logarithmic ratioscale called the decibel scale .
In general, a decibel scale for any quantity, q, is defined as:
ref
qqq
log10L dB (Equation 2.1)
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 3
8/3/2019 Analysis of Sound Waves
8/33
READING ANALYSIS OF SOUND WAVES
Note that the decibel is not an absolute measure but is referencedto a selected quantity, q ref .
Another reason for using this scale is that the ear itself 'hears'logarithmically and humans judge the relative loudness of twosounds by the ratio of their intensities, a logarithmic behaviour.
The Bel was named after Alexander Graham Bell (1847-1922), theScottish/American inventor of the telephone and worker for thedeaf.
As this unit is rather large it has been divided into ten smaller unitscalled decibels or dB . (deci = one tenth of).
A brief tutorial refresher on logarithms is available fromwww.comdis.wisc.edu/vcd202/Logs.html
When sound intensity is expressed as a decibel it is referred to assound intensity level and is given the symbol L I .
To convert sound intensity, I , to sound intensity level L I thefollowing relationship is used:
ref I
IIlog10L dB re I ref (Equation 2.2)
where I = sound intensity whose level is being specified, inwatts/m 2
and I ref = reference intensity = 10 -12 watts/m 2 (the threshold ofhearing)
Sound power, W , can also be expressed in decibels and is thenreferred to as the sound power level, L w .
ref W
WW
log10L dB re W ref (Equation 2.3)
where W = sound power of the source in watts
W ref = reference sound power = 10 -12 watts
PAGE 4 SAFETYLINE INSTITUTE JANUARY 2009
http://www.comdis.wisc.edu/vcd202/Logs.htmlhttp://www.comdis.wisc.edu/vcd202/Logs.htmlhttp://www.comdis.wisc.edu/vcd202/Logs.html8/3/2019 Analysis of Sound Waves
9/33
READING ANALYSIS OF SOUND WAVES
For sound pressure, p , we use the relationship:
Sound pressure level 2ref
2
p
p
plog10L
=ref p
plog20 dB re p ref (Equation 2.4)
where p = rms sound pressure in Pa
p ref = 2 x 10 -5 Pa
(sometimes written as 20 Pa = 20 x 10 -6 Pa, which is the soundpressure at the threshold of hearing at 1000 Hz)
The sound pressure level at the threshold of hearing is thus:
01log20102102
log20L 5--5
p dB
Review exercise 2.1Answers are at the end of this reading.
Using equation 2.4, calculate the sound pressure level of a soundwith a sound pressure of 2 Pa.
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 5
8/3/2019 Analysis of Sound Waves
10/33
READING ANALYSIS OF SOUND WAVES
Section 3: TYPICAL SOUND PRESSURE LEVELS
To get a feel for decibels, look at the table below which gives values for thesound pressure levels of common sounds in our environment. Also shown are thecorresponding sound pressures and sound intensities. From these you can seethat the decibel scale gives numbers in a much more manageable range.
Table of Sound Pressure Levels and Corresponding Sound Pressure and Sound Intensity
Examples Sound
Pressure
Level dB
SoundPressure
Pa
Sound Intensity watts/m
30m from jet aircraft 140 200 100
Threshold of pain 130 10
120 20 1
Chainsaw 110 0.1
Disco 100 2 0.01
90 0.001
Kerbside of busy road 80 0.2 0.0001
70 0.00001
Conversational speech 60 0.02 0.000001
50 0.0000001
40 0.002 0.00000001
Quiet bedroom at night 30 0.000000001
Background in TV studio 20 0.0002 0.0000000001
10 0.00000000001
Threshold of hearing 0 0.00002 0.000000000001
PAGE 6 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
11/33
READING ANALYSIS OF SOUND WAVES
From the above table you can see that a sound which has a soundpressure level 10 dB more than another has a sound intensity 10times as much which, as we saw in the first reading, means thatthe sound contains 10 times the energy.
A sound 20 dB more than another, has a sound intensity 100 timesas much and contains 100 times the energy.
A sound which is 3 dB more than another contains twice theenergy.
This is an important concept to remember when we come toassessing people's noise exposures, for if someone is receivingnoise 3 dB above the exposure standard, they are not merely 'justabove' the standard, but are receiving twice as much potentiallydamaging sound to their ears.
A different concept is that of loudness, a psychophysical sensationcaused by sound. Here an increase of 10 dB in sound pressurelevel causes the sound to be perceived as twice as loud. Adecrease of 10 dB is perceived as half as loud. So, if you are ableto introduce noise controls which make the sound half as loud, youhave actually reduced the energy getting to the ear by a factor of
10 - a very worthwhile effort.
The decibel scale some typical soundlevels
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 7
8/3/2019 Analysis of Sound Waves
12/33
READING ANALYSIS OF SOUND WAVES
Section 4: RELATIONSHIP BETWEEN SOUNDINTENSITY LEVEL, SOUND POWER LEVEL AND
SOUND PRESSURE LEVEL
The relationship between sound intensity level, sound power leveland sound pressure level for a point source in a free field (i.e. onewhere there are no reflecting surfaces) can now be considered.
We saw in the first reading that 2r 4W
I was the relationship of
intensity, I, to power, W
(where r = distance from the source).
Changing to levels
)r 4log(10WW
log10II
log10 2
ref ref
L I = L w - 10 log( r 2) - 10 log (4 )
= L w - 20 log r - 11 (Equation 2.5)
For air at 21 oC, we saw in the first reading that:
I = 0.0024 p2
So
12
2
ref I
10 p0024.0log10
IIlog10L
102
104 p
log10
= 2ref
2
p p
log10
= L p
The sign means approximately equal to. That is, the soundintensity level and the sound pressure level are approximatelynumerically equal.
PAGE 8 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
13/33
READING ANALYSIS OF SOUND WAVES
So using equation 2.5
L p L w - 20 log r - 11 (Equation 2.6)
From this you can see that if the distance from the source ( r ) isdoubled, the sound pressure level is decreased by (20 log 2),which is 6 dB - a relationship that was depicted in the first reading.
Review exercise 2.2Answers are at the end of this reading
If the sound power level of a machine is 102 dB what are thesound pressure levels:
at 2 m.at 4 m
assuming the source is in a free field?
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 9
8/3/2019 Analysis of Sound Waves
14/33
8/3/2019 Analysis of Sound Waves
15/33
READING ANALYSIS OF SOUND WAVES
If more than 2 sounds are to be added you need to do it two at atime.
Example: Add 4 sounds of 90, 91, 86 and 88 dB
First place in numerically increasing order i.e. 86, 88, 90, 91 dB.Add 86 and 88 dB using the table. This gives 90.1 dB. Now add90 dB to 90.1 dB. This gives 93.1 dB. Next add 91 to 93.1 dB. Thisgives 95.2 dB. Always remember to round to the nearest wholedecibel. So the total is 95 dB.
Review exercise 2.3Answers are at the end of this reading.
1. Add together two sounds of 94 dB and 99 dB.2. Add together 3 sounds of 96, 89 and 92 dB.
If you want to learn how to do the calculations mathematically (withthe aid of your electronic calculator or computer) and how toaverage decibels, go to Appendix A of this reading. This isoptional, but you will find this method much quicker when you are
adding more than 2 levels, once you get the hang of it.
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 11
8/3/2019 Analysis of Sound Waves
16/33
READING ANALYSIS OF SOUND WAVES
Section 6: SUBTRACTION OF DECIBELS
L total - L p1 Amount to be Subtracted
from L total to get L p2
0 greater than 10
1 6.8
2 4.5
3 3.0
4 2.2
5 1.6
6 1.2
7 1.0
8 0.7
9 0.6
10 0.5
Example: If the total soundpressure level is 96 dB and
source 1produces 89 dB by itself, thesound pressure level of source2 is:L p2 = 96 - 1 = 95 dB.
Review exercise 2.4Answers are at the end of this reading
If the sound pressure level at a worker's location is 93 dB with onemachine and the ventilation system operating and it is 87 dB withthe machine switched off and the ventilation still on, what is thesound pressure level due to the machine by itself?
PAGE 12 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
17/33
READING ANALYSIS OF SOUND WAVES
Section 7: FREQUENCY SPECTRUM OF A SOUND
A sound that consists of a single frequency is called a pure tone.
Nearly all sound sources emit sounds of more than one frequency.
Musical sounds contain a fundamental frequency plus severalharmonics (i.e. sounds with frequencies that are integral multiplesof the fundamental frequency). This combination tends to soundpleasant to the ear.
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 13
8/3/2019 Analysis of Sound Waves
18/33
READING ANALYSIS OF SOUND WAVES
Noise produced by most mechanical sources, such as machines,is made up of many different unrelated frequencies (wide bandnoise), and tends to sound unpleasant.
The above graph of the magnitude of the sound pressure level ateach frequency is called the frequency spectrum of the sound.
PAGE 14 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
19/33
READING ANALYSIS OF SOUND WAVES
Section 8: FREQUENCY ANALYSIS
It is often necessary to obtain information about the frequencyspectrum of a sound to design effective noise control and to selectappropriate personal hearing protectors.
8.1 Octave bandsIn most cases it is sufficient to measure the sound pressure levelin bands of frequencies, rather than at individual frequencies. Thewidth of the band usually chosen is the octave band - this is a
band where the upper frequency is twice that of the lower. Eachband is denoted by its centre frequency. Those usually measuredare the Internationally Preferred Frequencies of:
31.5Hz
63Hz
125Hz
250Hz
500Hz
1kHz
2kHz
4kHz
8kHz
16kHz
(k is a short way of writing kilo, which is 1000).and results are plotted on a graph like this:
This is a typical spectrum of a circular saw cutting aluminium.(Note that the line is simply a guide to move your eye from oneband to another and does not imply the magnitude at thefrequencies between the centre frequencies.)
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 15
8/3/2019 Analysis of Sound Waves
20/33
READING ANALYSIS OF SOUND WAVES
The limits of the octave bands are shown in the Table below:
Centre frequency, Hz Limits of band, Hz
31.5 22 - 4563 45 - 89
125 89 - 177
250 177 - 353
500 353 - 707
1000 707 - 1414
2000 1414 - 2828
4000 2828 - 5657
8000 5657 - 1131416000 11314 - 22627
Note that the centre frequency is the geometric mean and not theaverage of the band limit frequencies.
The lower and upper frequencies in the band can be found fromthe centre frequency by:
414.1f
2f f centrecentrelower (Equation 2.9)
and centrecentreupper f 414.12f f (Equation 2.10)
8.2 One-third octave bandsSometimes we want more detailed information than the octave
band analysis will give. This can be provided by selecting narrowerbands, such as one-third octave bands .
See Appendix B of this reading if you want more information onone-third octave bands. This is optional.
PAGE 16 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
21/33
READING ANALYSIS OF SOUND WAVES
8.3 Narrow band analysisFor even more detailed examination, narrow band analysis ispossible. This is used to pick up tonal noises with very narrowfrequency bandwidths that would be missed by octave or one-thirdoctave band analysis.
Note that in this example of noise from a fan the bandwidths areonly one-eighth of a hertz wide and we are only looking at therange 70 Hz to 80 Hz.
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 17
8/3/2019 Analysis of Sound Waves
22/33
READING ANALYSIS OF SOUND WAVES
Section 9: FREQUENCY WEIGHTING NETWORKS
9.1 A & C weighting networksSince the ear does not have an equal response to sounds ofdifferent frequencies we need to take this into account when wemeasure sound in relation to its effect on people. This is done bybuilding into sound measuring equipment an electrical networkwhich gives less weight to the frequencies to which the ear is lesssensitive. Several different weighting networks have beendeveloped over the years. The one which has been found to bestdescribe the damaging effect of noise is the A-weighting
network . This reduces the low frequency response and some ofthe high frequencies as shown in the diagram below.
Another weighting, which is useful when measuring peak noise orwhen estimating the attenuated noise when personal hearingprotectors are used, is the C-weighting network .
When the A- and C-weighting networks have been used in ameasurement, we denote this by writing the unit dB(A) or dB(C )respectively. When no weighting network is used we can denotethis by dB or dB(lin).
PAGE 18 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
23/33
READING ANALYSIS OF SOUND WAVES
9.2 Adjustments at octave bandcentre frequencies
From the weighting curves above, you can see that the followingare the adjustments at octave band centre frequencies:
Octave BandCentreFrequencies, Hz
31.5 63 125 250 500 1000 2000 4000 8000 16000
A-weightingadjustment, dB -39 -26 -16 -9 -3 0 +1 +1 -1 -7
C-weightingadjustment, dB -3 -1 0 0 0 0 0 -1 -3 -8
To obtain the overall A- or C-weighted sound pressure levels fromthe octave band sound pressure levels, the above adjustments aremade before adding, using one of the decibel addition methodsdescribed earlier.
EXAMPLE
What is the A-weighted sound pressure level in the cab of a diesellocomotive where the following octave band sound pressure levelswere measured?
Octave Band CentreFrequencies, Hz 31.5 63 125 250 500 1000 2000 4000 8000 16000
Diesel locomotiveoctave band levels, dB 104 102 92 90 87 82 80 68 60 57
A-weighting adjustment -39 -26 -16 -9 -3 0 +1 +1 -1 -7
A-weighted octave bandlevels, dB(A) 65 76 76 81 84 82 81 69 59 50
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 19
8/3/2019 Analysis of Sound Waves
24/33
READING ANALYSIS OF SOUND WAVES
Using the mathematical addition method or adding two at a timeusing the Table gives an A-weighted sound pressure level of88.7 dB(A), which we round to the nearest whole decibel giving89 dB(A).
Review exercise 2.5Answers are at the end of this reading.
Question 11. What is the C-weighted sound pressure level in the above
case?2. Is it higher or lower than the A-weighted level?
Question 2Now try the following addition of octave band levels of noise from acircular saw:
Octave Band CentreFrequencies, Hz 31.5 63 125 250 500 1000 2000 4000 8000 16000
Circular saw octave bandlevels, dB 73 75 77 80 87 85 88 96 92 87
1. What is the A-weighted level?2. What is the C-weighted level?3. Which is the higher?
PAGE 20 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
25/33
READING ANALYSIS OF SOUND WAVES
Question 3Look at the answers to questions 1 and 2 above and the octaveband frequency spectra of the diesel locomotive and the saw anddecide if the following statements are True or False.
1. The C-weighted level of a sound is always greater than the A-weighted level.
2. If the C-weighted level of a sound is significantly greater thanthe A-weighted level, the sound contains high levels of lowfrequency components.
3. If the A-weighted level of a sound is greater than the C-weighted level, the sound contains high levels of componentsin the 1000 - 4000 Hz range.
Once you have understood the answers to this exercise you willhave learnt a quick way (i.e. without having to do a full octaveband analysis) of checking where the main frequency componentsof a sound lie - which is very important in considering the types ofnoise reduction strategies to apply, as we shall see in laterreadings.
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 21
8/3/2019 Analysis of Sound Waves
26/33
READING ANALYSIS OF SOUND WAVES
APPENDICIES AND REVIEW EXERCISE ANSWERS
Appendix A mathematical addition and averagingof decibels
Addition of decibelsThe sound pressure levels must first be converted back to p 2 andthen added.
2ref
21
1 p p p
log10L and 2ref
22
2 p p p
log10L
For L p1 = 100 dB and L p2 = 98 dB
101 p2ref
21 10110loganti
10100
loganti10
Lloganti
p p
102 p2ref
2
2 1063.08.9loganti1098
loganti10
Lloganti p
p
The total mean-square sound pressure ratio is 1.63 x 10 10.
The total sound pressure level is:
)total(L p = 10 log (1.63 x 10 10) = 10 log 1.63 + 10 log 10 10
= 2.1 + 100= 102.1 dB= 102 dB to the nearest whole dB.
Note: We did not actually need to find the pressures, but only theirratios to the reference pressure.
In general, if you want to add any number n of sound pressurelevels ( L p1 , L p2 to L pn ) the formula is
L p(total) = 10 log (10
Lloganti......
10
Lloganti
10
Lloganti pn2 p1 p )
(Equation 2.7)
PAGE 22 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
27/33
READING ANALYSIS OF SOUND WAVES
Review Exercise A1
Add together two sounds of 94 dB and 99 dB
Review Exercise A2
Add together 3 sounds of 96, 89 and 92 dB.
Averaging Decibels
The average sound pressure level is found using -
L p(av) = 10 log 10
Lloganti......10
Lloganti10
Lloganti(n
1 pn2 p1 p ) (Equation 2.8)
Review Exercise A3
(i) What is the average sound pressure level of the 4 sounds withthe following sound pressure levels: 82, 90, 88 and 80 dB?
(ii) What (erroneous) answer would you get if you just averagedthe decibel values arithmetically?
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 23
8/3/2019 Analysis of Sound Waves
28/33
READING ANALYSIS OF SOUND WAVES
Appendix B One-third octave bandsOne-third octave band centre frequencies in the audible range are:25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500,630, 800, 1k, 1.25k, 1.6k, 2k, 2.5k, 3.15k, 4k, 5k, 6.3k, 8k, 10k,12.5k, 16k, 20k Hz.
The lower and upper frequencies of the one-third octave bands aregiven by:
122.1f
2f
f centre61centre
lower (Equation 2.11)
f upper = f centre x 2 = 1.122 x f centre (Equation 2.12)
Review Exercise B1
What are the lower and upper frequencies of the one-third octaveband with a centre frequency of 500 Hz?
PAGE 24 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
29/33
READING ANALYSIS OF SOUND WAVES
Review exercise answers2.1
Using equation 2.4, calculate the sound pressure level of a soundwith a sound pressure of 2 Pa.
Answer100dB
2.2
If the sound power level of a machine is 102 dB what are the
sound pressure levels:
at 2m.at 4m
assuming the source is in a free field.
Answer:85dB79dB
2.3
1. Add together two sounds of 94 dB and 99 dB.Answer: 100 dB
2. Add together 3 sounds of 96, 89 and 92 dB.Answer: 98 dB
2.4
If the sound pressure level at a worker's location is 93 dB with onemachine and the ventilation system operating and it is 87 dB withthe machine switched off and the ventilation still on, what is thesound pressure level due to the machine by itself?
Answer: 92 dB
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 25
8/3/2019 Analysis of Sound Waves
30/33
READING ANALYSIS OF SOUND WAVES
2.5
Question 1105 dB(C)
Higher
Question 2 99 dB(A)98 dB(C)The A-weighted level is higher
Question 3FalseTrueTrue
A1
Add together two sounds of 94 dB and 99 dB.
Answer
100dB
A2
Add together 3 sounds of 96, 89 and 92 dB.
Answer
98dB
PAGE 26 SAFETYLINE INSTITUTE JANUARY 2009
8/3/2019 Analysis of Sound Waves
31/33
READING ANALYSIS OF SOUND WAVES
A3
(i) What is the average sound pressure level of the 4 sounds withthe following sound pressure levels? 82, 90, 88 and 80 dB?Answer87dB
(ii) What (erroneous) answer would you get if you just averagedthe decibel values arithmetically?Answer
85dB
B1
What are the lower and upper frequencies of the one-third octaveband with a centre frequency of 500 Hz?Answer
f lower = 446 Hz
f upper = 561 Hz
JANUARY 2009 SAFETYLINE INSTITUTE PAGE 27
8/3/2019 Analysis of Sound Waves
32/33
READING ANALYSIS OF SOUND WAVES
PAGE 28 SAFETYLINE INSTITUTE JANUARY 2009
CONCLUSION
Now you have completed this reading, you should be familiar withthe terms used to analyse the magnitude of sound waves and theirfrequency components.
The decibel scale a logarithmic ratio scale was introduced toyou, along with the terms for the magnitude of a sound (soundintensity level, L I, sound power level, L W and sound pressurelevel, L p,) and their relationships.
Examples of sound pressure levels of everyday sounds were given
for you to become accustomed to the decibel scale.
You have also learnt how to add and subtract decibels, which willbe useful in assessing people's noise exposures to multiplesources and working out the most cost effective way of reducingnoise exposure in these situations.
The frequency spectrum of a sound has been discussed, followedby what we mean by frequency analysis into octave bands, one-third octave bands and narrow bands.
Finally the concept of frequency weighting has been presented,along with the two weightings most used in occupational noisemeasurements the A-weighting and the C-weighting.
Your feedbackWorkSafe is committed to continuous improvement. If you takethe time to complete the online Feedback Form at the SafetyLineInstitute website you will assist us to maintain and improve ourhigh standards.
8/3/2019 Analysis of Sound Waves
33/33
READING ANALYSIS OF SOUND WAVES
REFERENCES & FURTHER READING
Beranek, L. L, Noise and Vibration Control, Revised Edition,Institute of Noise Control Engineering, Washington, 1988.
Bies, D.A. and Hansen, C.H., Engineering Noise Control: Theory and Practice, 3rd Edition, E & FN Spon, London, 2003.
Norton, M. P., Fundamentals of noise and vibration analysis for engineers, Cambridge University Press, Cambridge, 1989.
01dB, Mediacoustic - Teaching Acoustics by Computer, 01dB,
France 1996. (An interactive CD-ROM)
A brief tutorial refresher on logarithms at the University ofWisconsin:www.comdis.wisc.edu/vcd202/Logs.html
Information on Alexander Graham Bell (1847-1922), theScottish/American inventor of the telephone and worker for thedeaf:www.sjsu.edu/depts/Museum/bel.html
On-line calculator for addition of decibels:www.sengpielaudio.com/calculator-spl.htm
http://www.comdis.wisc.edu/vcd202/Logs.htmlhttp://www.comdis.wisc.edu/vcd202/Logs.htmlhttp://www.sjsu.edu/depts/Museum/bel.htmlhttp://www.sjsu.edu/depts/Museum/bel.htmlhttp://www.sengpielaudio.com/calculator-spl.htmhttp://www.sengpielaudio.com/calculator-spl.htmhttp://www.sengpielaudio.com/calculator-spl.htmhttp://www.sjsu.edu/depts/Museum/bel.htmlhttp://www.comdis.wisc.edu/vcd202/Logs.html