Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Hindawi Publishing CorporationJournal of Applied MathematicsVolume 2009, Article ID 604695, 18 pagesdoi:10.1155/2009/604695
Research ArticleAnalytical Solution of the Hyperbolic HeatConduction Equation for Moving Semi-InfiniteMedium under the Effect of Time-DependentLaser Heat Source
R. T. Al-Khairy and Z. M. AL-Ofey
Department of Mathematics, King Faisal University, P.O. Box 1982, Dammam 31413, Saudi Arabia
Correspondence should be addressed to Z. M. AL-Ofey, [email protected]
Received 28 June 2008; Revised 2 March 2009; Accepted 12 May 2009
Recommended by George Jaiani
This paper presents an analytical solution of the hyperbolic heat conduction equation for movingsemi-infinite medium under the effect of time dependent laser heat source. Laser heating ismodeled as an internal heat source, whose capacity is given by g(x, t) = I(t)(1 − R)μe−μx whilethe semi-infinite body has insulated boundary. The solution is obtained by Laplace transformsmethod, and the discussion of solutions for different time characteristics of heat sources capacity(constant, instantaneous, and exponential) is presented. The effect of absorption coefficients on thetemperature profiles is examined in detail. It is found that the closed form solution derived fromthe present study reduces to the previously obtained analytical solution when the medium velocityis set to zero in the closed form solution.
Copyright q 2009 R. T. Al-Khairy and Z. M. AL-Ofey. This is an open access article distributedunder the Creative Commons Attribution License, which permits unrestricted use, distribution,and reproduction in any medium, provided the original work is properly cited.
1. Introduction
An increasing interest has arisen recently in the use of heat sources such as lasers andmicrowaves, which have found numerous applications related to material processing(e.g., surface annealing, welding and drilling of metals, and sintering of ceramics) andscientific research (e.g., measuring physical properties of thin films, exhibiting microscopicheat transport dynamics). Lasers are also routinely used in medicine. In literature, manyresearchers have investigated the heat transfer for moving medium under the effect of theclassical Fourier heat conduction model [1, 3–6].
In applications involving high heating rates induced by a short-pulse laser, the typicalresponse time is in the order of picoseconds [7–10]. In such application, the classical Fourierheat conduction model fails, and the use of Cattaneo-Vernotte constitution is essential [11,12].
2 Journal of Applied Mathematics
In this constitution, it is assumed that there is a phaselag between the heat flux vector(q) and the temperature gradient (∇T). As a result, this constitution is given as
q + τ∂q
∂t= −κ∇T, (1.1)
where κ is the thermal conductivity and τ is the relaxation time (phase lag in heat flux). Theenergy equation under this constitution is written as
ρCpτ∂2T
∂t2+ ρCp
∂T
∂t= κ∇2T +
(τ∂g
∂t+ g). (1.2)
In the literature, numerous works have been conducted using the microscopichyperbolic heat conduction model [10, 13–18]. To the authors’ knowledge, the thermalbehavior of moving semi-infinite medium subject to Time-Dependent laser heat source,under the effect of the hyperbolic heat conduction model, has not been investigated yet. Inthe present work, the thermal behavior of moving semi-infinite medium subject to Time-Dependent laser heat source, under the effect of the hyperbolic heat conduction model, isinvestigated.
2. Mathematical Model
In this paper heat distribution in a moving semi-infinite medium due to internal laser heatsource is considered. Our medium at t = 0 is occupying the region x ≥ 0 with insulatedsurface at x = 0. Moreover, at time t = 0, the temperature field within the medium is uniformwith a value T0 and stationary.
We consider first a semi-infinite medium moving with a constant velocity u in thedirection of the x-axis, if heat generation is present within the material, the balance law forthe internal energy can be expressed in terms of T as
ρCpDT
Dt+∂q
∂x= g(x, t), (2.1)
where
D
Dt≡ ∂
∂t+ u
∂
∂x, (2.2)
which denotes the material derivative.If the body is in motion, the Maxwell-Cattaneo law (1.1) leads to a paradoxical result so
that by replacing the partial time derivative in (1.1) with the material derivative operator, theparadox is removed, and the material form of the Maxwell-Cattaneo law is strictly Galileaninvariant. Therefore, (1.1) is replaced by [19]
q + τ(∂q
∂t+ u
∂q
∂x
)= −κ∂T
∂x. (2.3)
Journal of Applied Mathematics 3
Elimination of q between (2.1) and (2.3) yields the heat transport equation
τ∂2T
∂t2+∂T
∂t+ u
∂T
∂x+ 2τu
∂2T
∂x∂t+ τ(u2 − c2
)∂2T
∂x2=
1ρCp
[g + τ
∂g
∂t+ τu
∂g
∂x
], (2.4)
where the initial and boundary conditions are given by
T(x, 0) = T0,∂T
∂t
∣∣∣∣t=0
=g
ρCp, x ≥ 0, (2.5)
∂T
∂x(0, t)c = 0,
∂T
∂x(∞, t) = 0, t > 0. (2.6)
The relaxation time is related to the speed of propagation of thermal wave in the medium, c,by
τ =α
c2. (2.7)
The heat source term in (2.4) which describes the absorption of laser radiation is modeled as[20]
g(x, t) = I(t)(1 − R)μ exp(−μx), (2.8)
where I(t) is the laser incident intensity, R is the surface reflectance of the body, and μ is theabsorption coefficient.
We consider semi-infinite domains, which have initial temperature equal to theambient one. The following dimensionless variables are defined:
X =x
2cτ, η =
t
2τ, θ =
(T − T0)(Tm − T0)
, U =u
c, S =
τg
ρCp(Tm − T0). (2.9)
Equation (2.4) is expressed in terms of the dimensionless variables (2.9) as
2∂θ
∂η+ 2U
∂θ
∂X+∂2θ
∂η2+ 2U
∂2θ
∂η∂X−(
1 −U2) ∂2θ
∂X2=[
4S + 2∂S
∂η+ 2U
∂S
∂X
]. (2.10)
The dimensionless heat source capacity according to (2.8) is
S = ψ0φ(η)
exp(−βX), (2.11)
where
ψ0 =τIr(1 − R)μρCpT0
, φ(η)=I(2τη
)Ir
, β = 2cτμ. (2.12)
4 Journal of Applied Mathematics
The dimensionless initial conditions for the present problem are
θ(X, 0) = 0, (2.13)
∂θ
∂η(X, 0) = 2ψ0φ(0) exp
(−βX). (2.14)
The results from the assumption are that there is no heat flow in the body at the initialmoment [21], that is,
q(X, 0) = 0. (2.15)
The dimensionless boundary conditions are
∂θ
∂X
(0, η
)= 0, (2.16)
∂θ
∂X
(∞, η)= 0, η > 0. (2.17)
We substitute (2.11) for S in (2.10) to obtain
2∂θ
∂η+ 2U
∂θ
∂X+∂2θ
∂η2+ 2U
∂2θ
∂X∂η−(
1 −U2) ∂2θ
∂X2= 2ψ0
[(2 −Uβ)φ(η) + ∂φ
∂η
]exp
(−βX).(2.18)
3. Analytical Solution
Taking the Laplace transform of (2.18), using the initial conditions given by (2.13) and (2.14),yields
(1 −U2
) ∂2θ
∂X2− 2U(1 + s)
∂θ
∂X− s(2 + s)θ = −2ψ0
(2 + s −Uβ)φ exp
(−βX), (3.1)
where
θ(X, s) = L[θ(X, η
)], (3.2)
φ(s) = L[φ(η)]. (3.3)
The transformed boundary conditions given by (2.16) and (2.17) are
dθ
dX(0, s) = 0, (3.4)
dθ
dX(∞, s) = 0. (3.5)
Journal of Applied Mathematics 5
Equation (3.1) has homogeneous (θh) and particular (θp) solutions. Therefore, θ yields
θ = θh + θp. (3.6)
The mathematical arrangement of the solution of (3.1) is given in Appendix A.Consequently, (3.1) for X > 0 yields
θ(X, η
)=
⎧⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎨⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎩
2ψ0 exp(−βX)f(η), for η ≤ X
1 +U,
2ψ0 exp(−βX)f(η) − 2βψ0
∫ηX/1+U
exp(−y)I0
⎛⎝√
a
√(y +
UX
a
)2
− X2
a2
⎞⎠
×h8(η − y)dy − 2βψ0(1 +U)
∫ηX/1+U
exp(−y)I0
⎛⎝√a
√(y+
UX
a
)2
− X2
a2
⎞⎠
×h7(η − y)dy, for η >
X
1 +U,
(3.7)
where
0 < U < 1, (3.8)
f(η)=
12γ
∫η0φ(r)
{(γp −Uβ
)exp
[γm(η − r)] + (γm +Uβ
)exp
[−γp(η − r)]}dr, (3.9)
h7(η)= f
(η)+U2
∫η0φ(r)
[D1 exp
(−2(η − r)) +D2
+D3 exp(γm(η − r)) +D4 exp
(−γp(η − r))]dr,(3.10)
h8(η)= U
√a
∫η0
exp(−v)I1(√
av)h7(η − v)dv, (3.11)
γ =√
1 + β2, (3.12)
γm = γ − (1 −Uβ), (3.13)
γp = γ +(1 −Uβ), (3.14)
D1 =−Uβ
2(2 + γm
)(−2 + γp) , D2 =
−2 +Uβ2γmγp
,
D3 =
(γ + 1
)2γγm
(2 + γm
) , D4 =
(γ − 1
)2γγp
(−2 + γp) .
(3.15)
6 Journal of Applied Mathematics
4. Solutions for Special Cases of Heat Source Capacity
The temperature distributions resulting from any specified time characteristics of the heatsource φ(η) are available using the general hyperbolic solution (3.7)–(3.14). However, forsome particular φ(η) the general solution can be considerably simplified. Some of such casesare discussed below.
4.1. Source of Constant Strength: φ(η) = 1
This case may serve as a model of a continuously operated laser source. It may be also usedas a model of a long duration laser pulse when the short times (of the order of few or tens τ)are considered. For φ(η) = 1, (3.9) and (3.10) are reduced, respectively, to
f1(η)
=γp(γp +Uβ
)exp
(γmη
) − γm(γm −Uβ) exp(−γpη) − 2γ
(2 −Uβ)
2γγmγp, (4.1)
h7(1)(η)= f1
(η)+U2
{D1 exp
(−η) sinh(η)+D2η +
D3
γm
[exp
(γmη
) − 1]
+D4
γp
[1 − exp
(−γpη)]}.
(4.2)
4.2. Instantaneous Source: φ(η) = δ(η)
In this case, (3.9) and (3.10) take the form, respectively,
f2(η)=
12γ[(γp +Uβ
)exp
(γmη
)+(γm −Uβ) exp
(−γpη)], (4.3)
h7(2)(η)= f2
(η)+U2[D1 exp
(−2η)+D2 +D3 exp
(γmη
)+D4 exp
(−γPη)]. (4.4)
4.3. Exponential Source: φ(η) = exp(−νη)In this case (3.9) and (3.10) are as follows, respectively,
f3(η)=
12γ(ν − γp
)(ν + γm
) [(ν + γm)(γm −Uβ) exp
(−γpη) + (ν − γp)(γp +Uβ) exp(γmη
)
+2γ(2 − ν −Uβ) exp
(−νη)],(4.5)
h7(3)(η)= f3
(η)+U2
{D1
(−2 + ν)exp
(−2η)+D2
ν+
D3(ν + γm
) exp(γmη
)
+D4(
ν − γp) exp
(−γpη) +D5 exp(−νη)
},
(4.6)
Journal of Applied Mathematics 7
0
0.5
1
1.5
2
2.5
3
3.5
θ U = 0.7
U = 0
HyperbolicParabolic
0 2 4 6 8
X
Figure 1: Dimensionless temperature distributions resulting from the hyperbolic and parabolic modelswith dimensionless velocity of the medium for the heat source of constant strength; φ(η) = 1, ψ0 =1, and β = 1, η = 3.
0
2
4
6
θ X = 0
X = 3
X = 5
HyperbolicParabolic
0 2 4 6 8 10
η
Figure 2: Variation of dimensionless temperature with dimensionless time at different points of the bodyfor the heat source of constant strength; φ(η) = 1, ψ0 = 1, and U = 0.1.
where
D5 =D1
(2 − ν) −D2
ν− D3(
ν + γm) − D4(
ν − γp) . (4.7)
5. Results and Discussion
Using the solutions for arbitrary φ(η) and the solutions for the special cases we calculated,with the aid of the program Mathematica 5.0, and we performed calculations for metalsputting ψ0 = 1 and β = 0.5 or 1, since we assumed that typical values of the model parameters
8 Journal of Applied Mathematics
0
0.25
0.5
0.75
1
1.25
1.5
1.75
θ
β = 0.3
β = 1
β = 3
HyperbolicParabolic
0 1 2 3 4 5
X
Figure 3: Dimensionless temperature distributions at η = 1 for the heat source of constant strength andvarious values of β; φ(η) = 1, ψ0 = 1, and U = 0.1.
0
0.1
0.2
0.3
0.4
0.5
0.6
θU = 0
U = 0.5
HyperbolicParabolic
0 1 2 3 4
X
Figure 4: Dimensionless temperature distributions resulting from the hyperbolic and parabolic modelswith dimensionless velocity of the medium for the instantaneous heat source; φ(η) = δ(η), ψ0 = 1, β =3, and η = 2.
for metals are: μ of the order of 107–108 m−1,R of the order of 0.9, τ of the order of 10−13–10−11 s,and c of the order of 103–104 m/s [22–25]. Some solutions for other values of β are alsopresented to set off the specific features of our model. The results of calculations for varioustime characteristics of the heat source capacity are shown in Figures 1–9. Moreover, thevelocity of the medium was assumed not to exceed the speed of heat propagation.
The hyperbolic and parabolic solutions for the heat source of constant strength [φ(η) =1] are presented in Figures 1–3. Figure 1 shows the temperature distribution in the body forthe two values of dimensionless velocity of the medium, U = 0, 0.7. Figure 2 displays thetime variation of temperature at the three points of the body, X = 0, 3, 5. It is clearly seenthat for small X the temperatures predicted by the hyperbolic model are greater than thecorresponding values for the Fourier model, whereas in the region of intermediate valuesof X, the situation is just the opposite. For large X (X � η) the hyperbolic and parabolic
Journal of Applied Mathematics 9
0
0.2
0.4
0.6
0.8
1
1.2
θ
U = 0
U = 0.6
HyperbolicParabolic
0 2 4 6 8
X
Figure 5: Dimensionless temperature distributions with dimensionless velocity of the medium for theinstantaneous heat source; φ(η) = δ(η), ψ0 = 1, β = 1, and η = 2.
0
0.1
0.2
0.3
0.4
θ
η = 1
η = 2
η = 4η = 3
0 1 2 3 4 5
X
Figure 6: Dimensionless temperature distributions resulting from the hyperbolic model for theinstantaneous heat source; φ(η) = δ(η), ψ0 = 1, β = 5, and U = 0.1.
solutions tend to overlap. This behaviour can be explained as follows. In both models, theheat production is concentrated at the edge of the body. The same amounts of energy aregenerated continuously in both models, but in the case of hyperbolic models, because of thefinite speed of heat conduction, more energy is concentrated at the origin of X axis. Thisresults in the higher “hyperbolic” temperature in this region and the lower in the regionof intermediate X values. In Figure 3, we compare the temperature distributions at η = 1resulting from the hyberbolic and parabolic for the three values of β (β = 0.3, 1, and 3).For large β, that is, when the slope of the space characteristics of the heat source capacityincreases, in the hyperbolic solution, a blunt wave front can be observed. Figures 4–7 depictthe results of calculations for the instantaneous heat source [φ(η) = δ(η)]. A striking featureof the hyperbolic solutions is that the instantaneous heat source gives rise to a thermal pulsewhich travels along the medium and decays exponentially with time while dissipating itsenergy. During a period η, the maximum of the pulse moves over a distance X = η(1 + U).These effects are shown pictorially in Figures 4 and 6. Figure 4 presents the temperature
10 Journal of Applied Mathematics
0
0.2
0.4
0.6
0.8
1
θ
β = 1
β = 2
β = 5
0 1 2 3 4 5
X
HyperbolicParabolic
Figure 7: Dimensionless temperature distributions at η = 1 for the instantaneous heat source and variousvalues of β; φ(η) = δ(η), ψ0 = 1, and U = 0.1.
0
0.5
1
1.5
θ
U = 0.8
U = 0.4
U = 0.2
U = 0
0 2 4 6 8
X
Figure 8: Dimensionless temperature distributions with dimensionless velocity of the medium from thehyperbolic model for the exponential heat source ; φ(η) = exp(−0.4η), ψ0 = 1, β = 1, and η = 3.
distributions in the body for β = 5 and U = 0, 0.5, but Figure 6 presents the temperaturedistributions in the body for β = 5 and η = 1, 2, 3, 4. It is seen that the pulse is notsharp but blunt exponentially, which results from the fact that in our model the heat sourcecapacity decays exponentially along the x-axis. Figure 5 gives the hyperbolic and parabolictemperature distribution in the body at time η = 2 for the two values of dimensionlessvelocity of the medium, U = 0, 0.6. Figure 7 gives the hyperbolic and parabolic temperaturedistribution in the body at time η = 1 and velocity of the medium U = 0.1 for various valuesof β. As shown in Figure 7, the smaller β is, the more blunt the pulse and the shorter is thetime of its decay is . After the decay of the pulse, the differences between the hyperbolic andparabolic solutions become only quantitative, and they vanish in short time. Figures 8 and 9depict the results of calculations for the exponential heat source [φ(η) = exp(−νη)]. Figure 8gives the hyperbolic temperature distribution in the body at time η = 3 for the four valuesof dimensionless velocity of the medium, U = 0, 0.2, 0.4, 0.8. Figure 9 shows the temperaturedistribution in the body for the three values of dimensionless β (β = 0.3, 1, 3). The results are
Journal of Applied Mathematics 11
0
0.2
0.4
0.6
0.8
1
1.2
1.4
θ
β = 0.3
β = 1
β = 3
HyperbolicParabolic
0 1 2 3 4 5
X
Figure 9: Dimensionless temperature distributions at η = 1 for the exponential heat source and variousvalues of β; φ(η) = exp(−0.4η), ψ0 = 1, and U = 0.1.
compared with those obtained from an analytical model by Lewendowska [21]. For U = 0,our results are the same as those reported by Lewendowska [21].
6. Conclusions
This paper presents an analytical solution of the hyperbolic heat conduction equation formoving semi-infinit medium under the effect of Time-Dependent laser heat source. Laserheating is modeled as an internal heat source, whose capacity is given by (2.8) while thesemi-infinit body was insulated boundary. The heat conduction equation together with itsboundary and initial conditions have been written in a dimensionless form. By employing theLaplace transform technique, an analytical solution has been found for an arbitrary velocityof the medium variation. The temperature of the semi-infinit body is found to increase at largevelocities of the medium. The results are compared with those obtained from an analyticalmodel by Lewendowska [21]. For U = 0, our results are the same as those reported byLewendowska [21]. A blunt heat wavefront can be observed when the slope of the spacecharacteristics of the heat source capacity (i.e., the value of β) is large.
Appendix
A. Solution of Heat Transfer Equation
The characteristic equation for the homogeneous solution can be written as
r2 − 2U(1 + s)1 −U2
r − s(2 + s)1 −U2
= 0, (A.1)
which yields the solution of
r1,2 =U(1 + s)1 −U2
± 11 −U2
√(1 + s)2 − (1 −U2), (A.2)
where 0 < U < 1.
12 Journal of Applied Mathematics
Therefore, the homogeneous solution (θh) yields
θh = c1 exp(r1X) + c2 exp(r2X), (A.3)
or
θh =[c1 exp
(U(1 + s)
a− 1a
√(1 + s)2 − a
)X + c2 exp
(U(1 + s)
a+
1a
√(1 + s)2 − a
)X
],
(A.4)
where a = 1 −U2.For the particular solution, one can propose θp = A0 exp(−βX).Consequently, substitution of θp into (3.1) results in
(1 −U2
)β2A0 exp
(−βX) + 2U(1 + s)βA0 exp(−βX) − s(2 + s)A0 exp
(−βX)
= −2ψ0(2 + s −Uβ)φ exp
(−βX),(A.5)
where
A0 =−2ψ0
(2 + s −Uβ)φ[
(1 −U2)β2 + 2U(1 + s)β − s(2 + s)] , (A.6)
or
θ = c1 exp(U(1 + s)
a− 1a
√(1 + s)2 − a
)X
+ c2 exp(U(1 + s)
a+
1a
√(1 + s)2 − a
)X
+2ψ0
(2 + s −Uβ)φ exp
(−βX)(s − γm
)(s + γp
) .
(A.7)
Since Re(s) > 0, 0 < U < 1 and dθ/dX(∞, s) = 0, then c2 = 0.Therefore,
θ = c1 exp(U(1 + s)
a− 1a
√(1 + s)2 − a
)X +
2ψ0(2 + s −Uβ)φ exp
(−βX)(s − γm
)(s + γp
) . (A.8)
Journal of Applied Mathematics 13
By applying the boundary condition (3.4), we can obtain c1, that is,
dθ
dX={c1
(U(1 + s)
a− 1a
√(1 + s)2 − a
)× exp
(U(1 + s)
a− 1a
√(1 + s)2 − a
)X
−2βψ0(2 + s −Uβ)φ exp
(−βX)(s − γm
)(s + γp
)}X=0
= 0,
(A.9)
or
c1 =2βψ0a
(2 + s −Uβ)φ(
U(1 + s) −√(1 + s)2 − a
)(s − γm
)(s + γp
) . (A.10)
Hence,
θ =2βψ0a
(2 + s −Uβ)φ exp
(U(1 + s)/a − (1/a)
√(1 + s)2 − a
)X
(U(1 + s) −
√(1 + s)2 − a
)(s − γm
)(s + γp
)
+2ψ0
(2 + s −Uβ)φ exp
(−βX)(s − γm
)(s + γp
) .
(A.11)
Let H1 and H2 be
H1 =a(2 + s −Uβ)φ exp
(U(1 + s)/a − (1/a)
√(1 + s)2 − a
)X
(U(1 + s) −
√(1 + s)2 − a
)(s − γm
)(s + γp
)
−
⎡⎢⎢⎣
exp(−(X(1 + s))/(1 +U)) exp(−(X/a)
(√(1 + s)2 − a − (1 + s)
))√(1 + s)2 − a
×U
[(1 + s) −
√(1 + s)2 − a
]√(1 + s)2 − a
×
((1 + s)2 − a
)(2 + s −Uβ)φ(
(1 + s)2 − 1)(s − γm
)(s + γp
)⎤⎥⎥⎦
14 Journal of Applied Mathematics
− (1 +U)
⎡⎢⎢⎣
exp(−X(1 + s)/(1 +U)) exp(−(X/a)
(√(1 + s)2 − a − (1 + s)
))√(1 + s)2 − a
×
((1 + s)2 − a
)(2 + s −Uβ)φ(
(1 + s)2 − 1)(s − γm
)(s + γp
)⎤⎥⎦
= −H3 − (1 +U)H4,
(A.12)
H2 =
(2 + s −Uβ)φ(s − γm
)(s + γp
) , (A.13)
Consequently,
θ(X, η
)= £−1θ = 2βψ0£−1H1 + 2ψ0 exp
(−βX)£−1H2
= −2βψ0£−1H3 − 2βψ0(1 +U)£−1H4 + 2ψ0 exp(−βX)£−1H2.
(A.14)
To obtain the inverse Laplace transformation of functions H2,H3, and H4, we use theconvolution for Laplace transforms.
The Laplace inverse of H2 can be obtained as
£−1H2 =1
2γ
∫η0φ(r)
[(γp +Uβ
)exp
(γm(η − r)) + (γm −Uβ) exp
(−γp(η − r))]dr= f
(η).
(A.15)
To obtain the inverse Laplace transformation of function H3, we use the convolutionfor Laplace transforms:
£−1H3 = £−1[H5(s)H6(s)H7(s)] =∫η
0h5(y)∫η−y
0h6(v)h7
(η − y − v)dv dy, (A.16)
where
h5(η)= £−1H5 = £−1
⎧⎪⎪⎨⎪⎪⎩
exp(−(X(1 + s)/(1 +U))) exp(−(X/a)
(√(1 + s)2 − a − (1 + s)
))√(1 + s)2 − a
⎫⎪⎪⎬⎪⎪⎭
= exp(−η)£−1
⎧⎨⎩
exp(−(X/(1 +U))s) exp(−(X/a)
(√s2 − a − s
))√s2 − a
⎫⎬⎭.
(A.17)
Journal of Applied Mathematics 15
It is noted from the Laplace inversion that [26]
£−1{H(s − b)} = exp(bη)h(η), (A.18)
£−1
⎧⎨⎩
exp(−k(√
s2 − c2 − s))
√s2 − c2
⎫⎬⎭ = I0
(c√η2 + 2kη
), k ≥ 0, (A.19)
£−1{exp(−bs)H(s)}=
⎧⎨⎩h(η − b) at η > b,
0 at η < b,b > 0. (A.20)
Therefore,
h5(η)= £−1H5 = exp
(−η)I0
⎛⎝√
a
√(η +
UX
a
)2
− X2
a2
⎞⎠, η >
X
1 +U. (A.21)
Similarly, £−1H6 can be obtained, that is,
h6(η)= £−1H6 = £−1
⎧⎪⎪⎨⎪⎪⎩U
[(1 + s) −
√(1 + s)2 − a
]√(1 + s)2 − a
⎫⎪⎪⎬⎪⎪⎭
= U exp(−η)£−1
⎧⎨⎩[s −
√s2 − a
]√s2 − a
⎫⎬⎭.
(A.22)
It is noted from the Laplace inversion that [26]
£−1
⎧⎪⎨⎪⎩
[s −
√s2 − c2
]ν√s2 − c2
⎫⎪⎬⎪⎭ = cνIν
(cη), ν > −1. (A.23)
Therefore,
h6(η)= £−1H6 =
√aU exp
(−η)I1(√
aη). (A.24)
16 Journal of Applied Mathematics
To obtain the inverse transformation of function H7, we use the convolution forLaplace transforms:
h7(η)= £−1H7 = £−1
⎧⎨⎩
((1 + s)2 − a
)(2 + s −Uβ)φ(
(1 + s)2 − 1)(s − γm
)(s + γp
)⎫⎬⎭
= f(η)+U2
∫η0φ(r)
[D1 exp
(−2(η − r)) +D2 +D3 exp
(γm(η − r))
+D4 exp(−γp(η − r))]dr.
(A.25)
Substituting (A.21), (A.24), and (A.25) into (A.16), it yields
£−1H3 =∫ηX/(1+U)
exp(−y)I0
⎛⎝√
a
√(y +
UX
a
)2
− X2
a2
⎞⎠ × h8
(η − y)dy, (A.26)
where
h8(η)=∫η
0
√aU exp(−v)I1
(√av) × h7
(η − v)dv. (A.27)
Similarly, £−1H4 can be obtained, after using the convolution for Laplace transformsand (A.21) and (A.25):
£−1H4 = £−1[H5(s)H7(s)]
=∫ηX/(1+U)
exp(−y)I0
⎛⎝√
a
√(y +
UX
a
)2
− X2
a2
⎞⎠ × h7
(η − y)dy. (A.28)
Substituting (A.15), (A.26), and (A.28) into (A.14), it yields
θ(X, η
)=
⎧⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎨⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎪⎩
2ψ0 exp(−βX)f(η), for η ≤ X
1 +U,
2ψ0 exp(−βX)f(η) − 2βψ0
∫ηX/(1+U)
exp(−y)I0
⎛⎝√
a
√(y +
UX
a
)2
− X2
a2
⎞⎠
×h8(η − y)dy − 2βψ0(1 +U)
∫ηX/(1+U)
exp(−y)I0
⎛⎝√
a
√(y+
UX
a
)2
−X2
a2
⎞⎠
×h7(η − y)dy, for η >
X
1 +U.
(A.29)
Journal of Applied Mathematics 17
Nomenclature
Cp: Specific heat at constant pressure, J/(kg K)g: Capacity of internal heat source, W/m3
I: Laser incident intensity, W/m2
Ir : Arbitrary reference laser intensityI0: Modified Bessel function, 0th orderI1: Modified Bessel function, 1th orderL: Laplace operatorR: Surfase reflectances: Laplace variableq: Heat flux vector, W/m2
t: Time, sT : Temperature, KTm, T0: Arbitrary reference temperatures, Kc: Speed of heat propagation = (α/τ)1/2, m/sx, y, z: Cartesian coordinates, mX,Y,Z: Dimensionless cartesian coordinatesS: Dimensionless capacity of internal heat sourceu: Velocity of the medium, m/sU: Dimensionless velocity of the medium, u/c.
Greek symbols
α: Thermal diffusivity = κ/(ρCp), m2/sκ: Thermal conductivity, W/(mK)τ : Relaxation time of heat flux, sβ: Dimensionless absorption coefficientγ, γm, γp: Auxiliary coefficients defined by (3.12), (3.13), (3.14), respectivelyφ: Dimensionless rate of energy absorbed in the mediumμ: Absorption coefficientθ: Dimensionless temperaturesρ: Densityη: dimensionless timeψ0: Internal heat sourceθ: Laplace transformation of dimensionless temperature.
References
[1] J. C. Jaeger, “Moving source of heat and the temperature at sliding contacts,” Proceedings of the RoyalSociety of NSW, vol. 76, pp. 203–224, 1942.
[2] J. C. Jaeger and H. S. Carslaw, Conduction of Heat in Solids, Oxford University Press, Oxford, UK, 1959.[3] M. Kalyon and B. S. Yilbas, “Exact solution for time exponentially varying pulsed laser heating:
convective boundary condition case,” Proceedings of the Institution of Mechanical Engineers, Part C, vol.215, no. 5, pp. 591–602, 2001.
[4] M. N. Ozisik, Heat Conduction, Wiley, New York, NY, USA, 2nd edition, 1993.[5] D. Rosenthal, “The theory of moving sources of heat and its application to metal treatments,”
Transaction of the American Society of Mechanical Engineers, vol. 68, pp. 849–866, 1946.
18 Journal of Applied Mathematics
[6] B. S. Yilbas and M. Kalyon, “Parametric variation of the maximum surface temperature during laserheating with convective boundary conditions,” Journal of Mechanical Engineering Science, vol. 216, no.6, pp. 691–699, 2002.
[7] M. A. Al-Nimr and V. S. Arpaci, “Picosecond thermal pulses in thin metal films,” Journal of AppliedPhysics, vol. 85, no. 5, pp. 2517–2521, 1999.
[8] M. A. Al-Nimr, “Heat transfer mechanisms during short-duration laser heating of thin metal films,”International Journal of Thermophysics, vol. 18, no. 5, pp. 1257–1268, 1997.
[9] T. Q. Qiu and C. L. Tien, “Short-pulse laser heating on metals,” International Journal of Heat and MassTransfer, vol. 35, no. 3, pp. 719–726, 1992.
[10] C. L. Tien and T. Q. Qiu, “Heat transfer mechanism during short pulse laser heating of metals,”American Society of Mechanical Engineers Journal of Heat Transfer, vol. 115, pp. 835–841, 1993.
[11] C. Catteneo, “A form of heat conduction equation which eliminates the paradox of instantaneouspropagation,” Compte Rendus, vol. 247, pp. 431–433, 1958.
[12] P. Vernotte, “Some possible complications in the phenomenon of thermal conduction,” Compte Rendus,vol. 252, pp. 2190–2191, 1961.
[13] M. A. Al-Nimr and V. S. Arpaci, “The thermal behavior of thin metal films in the hyperbolic two-stepmodel,” International Journal of Heat and Mass Transfer, vol. 43, no. 11, pp. 2021–2028, 2000.
[14] M. A. Al-Nimr, O. M. Haddad, and V. S. Arpaci, “Thermal behavior of metal films-A hyperbolic two-step model,” Heat and Mass Transfer, vol. 35, no. 6, pp. 459–464, 1999.
[15] M. A. Al-Nimr, B. A. Abu-Hijleh, and M. A. Hader, “Effect of thermal losses on the microscopichyperbolic heat conduction model,” Heat and Mass Transfer, vol. 39, no. 3, pp. 201–207, 2003.
[16] M. Naji, M.A. Al-Nimr, and M. Hader, “The validity of using the microscopic hyperbolic heatconduction model under a harmonic fluctuating boundary heating source,” International Journal ofThermophysics, vol. 24, no. 2, pp. 545–557, 2003.
[17] M. A. Al-Nimr and M. K. Alkam, “Overshooting phenomenon in the hyperbolic microscopic heatconduction model,” International Journal of Thermophysics, vol. 24, no. 2, pp. 577–583, 2003.
[18] D. Y. Tzou, Macro-to-Microscale Heat Transfers-The Lagging Behavior, Taylor & Francis, New York, NY,USA, 1997.
[19] C. I. Christov and P. M. Jordan, “Heat conduction paradox involving second-sound propagation inmoving media,” Physical Review Letters, vol. 94, no. 15, Article ID 154301, 4 pages, 2005.
[20] S. M. Zubair and M. A. Chaudhry, “Heat conduction in a semi-infinite solid due to time-dependentlaser source,” International Journal of Heat and Mass Transfer, vol. 39, no. 14, pp. 3067–3074, 1996.
[21] M. Lewandowska, “Hyperbolic heat conduction in the semi-infinite body with a time-dependent laserheat source,” Heat and Mass Transfer, vol. 37, no. 4-5, pp. 333–342, 2001.
[22] S. H. Chan, J. D. Low, and W. K. Mueller, “Hyperbolic heat conduction in catalytic supportedcrystallites,” AIChE Journal, vol. 17, pp. 1499–1501, 1971.
[23] L. G. Hector Jr., W. S. Kim, and M. N. Ozisik, “Propagation and reflection of thermal waves in a finitemedium due to axisymmetric surface sources,” International Journal of Heat and Mass Transfer, vol. 35,no. 4, pp. 897–912, 1992.
[24] D. Y. Tzou, “The thermal shock phenomena induced by a rapidly propagating crack tip: experimentalevidence,” International Journal of Heat and Mass Transfer, vol. 35, no. 10, pp. 2347–2356, 1992.
[25] A. Vedavarz, S. Kumar, and M. K. Moallemi, “Significance of non-Fourier heat waves in conduction,”Journal of Heat Transfer, vol. 116, no. 1, pp. 221–226, 1994.
[26] R. V. Churchill, Operational Mathematics, McGraw-Hill, New York, NY, USA, 1958.
Submit your manuscripts athttp://www.hindawi.com
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical Problems in Engineering
Hindawi Publishing Corporationhttp://www.hindawi.com
Differential EquationsInternational Journal of
Volume 2014
Applied MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Probability and StatisticsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Mathematical PhysicsAdvances in
Complex AnalysisJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
OptimizationJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
CombinatoricsHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Operations ResearchAdvances in
Journal of
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Function Spaces
Abstract and Applied AnalysisHindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
International Journal of Mathematics and Mathematical Sciences
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
The Scientific World JournalHindawi Publishing Corporation http://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Algebra
Discrete Dynamics in Nature and Society
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Decision SciencesAdvances in
Discrete MathematicsJournal of
Hindawi Publishing Corporationhttp://www.hindawi.com
Volume 2014 Hindawi Publishing Corporationhttp://www.hindawi.com Volume 2014
Stochastic AnalysisInternational Journal of