ANNUAL REPAIR AND MAINTENANCE OF (CIVIL …esichennai.org/rochennai/Financial Bid-170317.pdfHalf brick masonry with common burnt clay F.P.S ... universal hydraulic door closer (having

ANNEXURE 'D'

In Figures In Words

1 1.1 Carriage of materials

1.11.1.2 Lead 15 Km earth

Cum 99.46

2

2.8

Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means in foundation trenches or drains (not

exceeding 1.5 m in width or 10 sqm on plan), including dressing of

sides and ramming of bottoms, lift upto 1.5 m, including getting out

the excavated soil and disposal of surplus excavated soil as directed,

within a lead of 50 m.

2.12.8.1 All kinds of soil

Cum 122.5

32.1

Excavating trenches of required width

for pipes, cables etc3.1 2.10.1 All kinds of soil

3.1.12.10.1.2

Pipes cables tec. Exceeding 80mm dia

but not exceeding 300mm dia Mtr 200

4

2.27Supplying and filling in plinth with river sand under floors,

including watering, ramming consolidating and dressing complete.Cum 10

5

2.31

Clearing jungle including uprooting of rank vegetation, grass, brush

wood, trees and saplings of girth up to 30 cm measured at a height

of 1 m above ground level and removal of rubbish up to a distance

of 50 m outside the periphery of the area cleared.Sqm 34740

6

2.33

Felling trees of the girth (measured at a height of 1 m above ground

level) including cutting of trunks and branches, removing the roots

and stacking of serviceable material and disposal of unserviceable

material.

6.1.12.33.2 Beyond 60 cm girth up to and including 120 cm girth

Each 25

ANNUAL REPAIR AND MAINTENANCE OF (CIVIL AND ELECTRICAL) WORKS, SUPPLY OF DIESEL TO 2000 KVA DG SET OF ESI HOSPITAL &

STAFF QUARTERS AT VARADARAJAPURAM, COIMBATORE AND DISPENSARIES AND STAFF QUARTERS AT SOWRIPALAYAM, UPPILIPALAYAM

AND VELLALORE FOR THE YEAR 2017-18FINANCIAL BID

Item

No

DSR Item

No.Description Qty Units

RateTotal

Page 1 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

7

2.35

Diluting and injecting chemical emulsion for

POSTCONSTRUCTIONAL

anti-termite treatment (excluding the cost of chemical emulsion)

7.1.1

2.35.5

Treatment at points of contact of wood work by chemical

emulsion Chlorpyriphos/ Lindane (in oil or kerosene based

solution) @ 0.5 litres per hole by drilling 6 mm dia holes at

downward angle of 45 degree at 150 mm centre to centre and

sealing the same. Mtr 60

8

4.1

Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering - All work up to

plinth level:

8.14.1.3

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) Cum 6.885

94.1.8


nominal size) Cum 10

9.1 4.1.8 For Plinth protection

10

4.5

Providing and fixing up to floor five level precast cement concrete

string or lacing courses, copings, bed plates, anchor blocks, plain

window sills, shelves, louvers, steps, stair cases, etc. including

hoisting and setting in position with cement mortar

10.14.5.1

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm


11

5.1

Providing and laying in position specified grade of reinforced

cement concrete, excluding the cost of centering, shuttering,

finishing and reinforcement - All work up to plinth level :

11.15.1.3



125.9

Centering and shuttering including strutting, propping etc. and

removal of form for :

12.15.9.3 Suspended floors, roofs, landings, balconies and access platform

Sqm 20

13

5.9.15

Small lintels not exceeding 1.5 m clear span, moulding as in

cornices, window sills, string courses, bands, copings, bed plates,

anchor blocks and the like Sqm 10

Page 2 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

13.1 5.9.15 Hospital and Dispensaries

13.15.9.19 Weather shade, Chajjas, corbels etc., including edges

Sqm 10

14

5.22

Steel reinforcement for R.C.C. work including straightening,

cutting, bending, placing in position and binding all complete upto

plinth level

14.15.22.6 Thermo-Mechanically Treated bars

Kgs 490.4

15

6.1Brick work with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundation and plinth in :

15.16.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

Cum 20

16

6.4

Brick work with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in superstructure above plinth level up to floor

V level in all shapes and sizes in :

16.16.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

Cum 30

17

6.12Half brick masonry with common burnt clay F.P.S (non modular

bricks) of class designation 7.5 in foundation and plinth

17.16.12.2 Cement mortor 1:4 (1 cement: 4 coarse sand)

Sqm 30

18

6.13

Half brick masonry with common burnt clay F.P.S. (non modular)

bricks of class designation 7.5 in superstructure above plinth level

up to floor V level.

18.16.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)

Sqm 30

19

8.2

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms,

vanity counters, window sills, facias and similar locations, of

required size, approved shade, colour and texture laid over 20 m

Page 3 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

19.18.2.1

Raj Nagar Plain white marble / Udaipur green marble / Zebra black

marble

19.1.18.2.1.2 Area of slab over 0.50 sqm

Sqm 20

20 8.2.2 Granite of any colour and shade

20.18.2.2.2 Area of slab over 0.50 sqm

Sqm 10

21

9.1

Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required dia & length (

hold fast lugs or dash fastener shall be paid for separately).

21.19.1.2 Sal wood

Cum 0.1

22

9.5

Providing and fixing panelled or panelled and glazed shutters for

doors, windows and clerestory windows, including ISI marked

M.S.pressed butt hinges bright finished of required size with

necessery screws, excluding panelling which will be paid for separa

22.1 9.5.1 Second class teak wood

9.5.1.1 35 mm thick shuttersSqm 4

23

9.18

Providing and fixing Pre-laminated flat pressed 3 layer (medium

density) particle board or graded wood particle board IS : 3087

marked, with one side decorative and other side balancing

lamination Grade I, Type II exterior grade IS : 12823 marked, in

shel

23.19.18.2 25 mm thick

Sqm 2

24

9.20

Providing and fixing ISI marked flush door shutters conforming to

IS : 2202 (Part I) decorative type, core of block board construction

with frame of 1 st class hard wood and well matched teak 3 ply

veneering with vertical grains or cross bands and face ve

Page 4 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

24.19.20.2

30 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws Sqm 21

25

9.46

Providing and fixing curtain rods of 1.25 mm thick chromium

plated brass plate, with two chromium plated brass brackets fixed

with C.P. brass screws and wooden plugs, etc., wherever necessary

complete:

25.19.46.2 20 mm dia

Mtr 10

26

9.48

Providing and fixing M.S. grills of required pattern in frames of

windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete.

26.19.48.2 Fixed to openings/ wooden frames with rawl plugs screws etc

Kgs 750

27

9.83

Providing and fixing aluminium die cast body tubular type

universal hydraulic door closer (having brand logo with ISI, IS :

3564, embossed on the body, door weight upto 35 kg and door

width upto 700 mm), with necessary accessories and screws etc.

complet Each 5

28

9.95

Providing and fixing ISI marked aluminium butt hinges anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade with necessary

screws etc. complete :

28.19.95.1 125x75x4 mm

Each 40

28.1.19.95.3 100x63x4 mm

Each 40

28.1.29.95.6 75x63x4 mm

Each 40

29

9.96

Providing and fixing aluminium sliding door bolts, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS : 1868),

transparent or dyed to required colour or shade, with nuts and

screws etc. complete:

Page 5 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

29.19.96.1 300x16 mm

Each 40

29.1.19.96.2 250x16 mm

Each 40

30

9.97

Providing and fixing aluminium tower bolts, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868 ),

transparent or dyed to required colour or shade, with necessary


30.19.97.2 250x10 mm

Each 40

30.1.19.97.4 150x10 mm

Each 40

30.1.29.97.5 100x10 mm

Each 40

31

9.100

Providing and fixing aluminium handles, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade, with necessary


31.19.100.2 100 mm

Each 40

31.1.19.100.3 75 mm

Each 40

32

9.101

Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised (anodic coating not less than grade AC 10 as per

IS : 1868) transparent or dyed to required colour and shade, with

necessary screws etc. complete.

32.19.101.1 Single rubber stopper

Each 40

32.1.19.101.2 Twin rubber stopper

Each 10

Page 6 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

33

9.113

Providing and fixing bright finished 100 mm mortice lock with 6

levers without pair of handles of approved quality for aluminium

door, with necessary screws etc complete as per direction of

Engineer-in-charge. Each 2

34

9.117

Providing and fixing factory made uPVC door frame made of uPVC

extruded sections having an overall dimension as below (tolerance

±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door

frame to be Jointed with galvanized brackets and stainless steel

screws, joints mitred and plastic welded. The hinge side vertical of

the frames reinforced by galvanized M.S. tube of size 19 X 19 mm

and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges

fixed to the frame complete as per manufacturer's specification and

direction of Engineer-in-charge

34.19.117.2 Extruded section profile size 42x50 mm

RM 260.1

35

9.120

Providing and fixing factory made panel PVC door shutter

consisting of frame made out of M.S. tubes of 19 gauge thickness

and size of 19 mm x 19 mm for styles and 15x15 mm for top &

bottom rails. M.S. frame shall have a coat of steel primers of

approved make and manufacture . M.S. frame covered with 5 mm

thick heat moulded PVC 'C' channel of size 30 mm thickness, 70

mm width out of which 50 mm shall be flat and 20 mm shall be

tapered in 45 degree angle on both side forming styles and 5 mm

thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and

20 mm shall be tapered in 45 degree on the inner side to form top

and bottom rail and 115 mm wide PVC sheet out of which 75 mm

shall be flat and 20 mm shall be tapered on both sides to form lock

rail. Top, bottom and lock rails shall be provided both side of the

panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be

provided as gap insert for top rail & bottom rail. paneling of 5 mm

thick both side PVC sheet to be fitted in the M.S. frame welded/

sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm

wide PVC sheet beading on inner side, and joined together with

solvent cement adhesive. An additional 5 mm thick PVC strip of 20

Page 7 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

35.1 9.120.1 30 mm thick plain PVC door shutters Sqm 81.6

36

9.128

Providing and fixing factory made Fiberglass Reinforced plastics

(F.R.P.)

chajja 4 mm thick of required colour, size and design made by Resin

Transfer Moulding (RTM) Machine Technology, resulting in void

free

compact laminate in single piece, having smooth gradual slope

curvature for easy drainage of water and duly reinforced by 2nos

vertically and 1nos horizontally 50x2 mm thick M.S. flat with 12

mm in built hole for grouting on the existing wall along with the 50

mm flanges duly inserted and sealed in the wall complete in one

single piece casted onolithically, including all necessary fittings .

The FRP Chajja should be manufactured using unsaturated

Polyester resin as per IS: 6746, duly reinforced with fibre glass

chopped strand mat (CSM) as per IS: 11551 complete with

protective Gel coat U/V coating on Top for complete resistance

from the extreme of temperature, weather & sunlight

Sqm 10

37

10.25

Steel work welded in built up sections / framed work, including

cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer using structural steel etc. as required.

37.110.25.2

In gratings, frames, guard bar, ladder, railings, brackets, gates and

similar works Kgs 789.6

38

11.2

Chequerred precast cement concrete tiles 22mm thick in footpath &

out yard jointed with neat cement slurry mixed with pigment to

match the shade of tiles including rubbing and cleaning etc.

complete on 20mm thick bed of cement mortar 1:4 (1 cement : 4

coarse sand)

38.111.20.3 Dark shade using ordinary cement

Sqm 10

Page 8 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

39

11.26

Kota stone slab flooring over 20 mm (average) thick base laid over

and jointed with grey cement slurry mixed with pigment to match

the shade of the slab, including rubbing and polishing complete

with base of cement mortar 1 : 4 (1 cement : 4 coarse sand)

39.1 11.26.1 25 mm thick Sqm 20

40

11.27

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and

pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement:

3

coarse sand) and jointed with grey cement slurry mixed with

pigment to

match the shade of the slabs, including rubbing and polishing

complete. Sqm 20

41

11.36

Providing and fixing 1st quality ceramic glazed wall tiles

conforming to IS : 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except

burgundy, bottle green, black of any size as approved by Engineer-

in-Charg Sqm 300

42

11.37

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer), of 1st quality

conforming to IS : 15622, of approved make, in colours such as

White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cemenSqm 200

4311.41.2 Vitrified tiles laid and pasted over existing floor tiles

Sqm 250

44

12.41

Providing and fixing on wall face unplasticised Rigid PVC rain

water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

44.112.41.1 75 mm diameter

RM 50

44.1.112.41.2 110 mm diameter

RM 175

Page 9 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

45

12.42

Providing and fixing on wall face unplasticised-PVC moulded

fittings / accessories for unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

45.112.42.1.2 Coupler 110 mm dia

Each 40

45.1.112.42.3.2 Single tee with door - 110x110x110 mm

Each 40

45.1.212.42.5.2 Bend 87.5° - 110 mm bend

Each 40

45.1.312.42.6.2 Shoe (Plain) 110 mm Shoe

Each 40

46

12.43

Providing and fixing unplasticised-PVC pipe clips of approved

design to unplasticised-PVC rain water pipes by means of 50x50x50

mm hard wood plugs, screwed with M.S. screws of required length,

including cutting brick work and fixing in cement mortar 1:4 (1

cement : 4 coarse sand) and making good the wall etc. complete.

46.112.43.2 110 mm

Each 200

4813.5

15 mm cement plaster on rough side of single or half brick wall of

mix:

48.113.5.1 1:4 (1 cement : 4 coarse sand)

Sqm 100

49

13.26

Providing and applying plaster of paris putty of 2 mm thickness

over plastered surface to prepare the surface even and smooth

complete. Sqm 600

5014.66

Finishing walls with Acrylic Smooth exterior paint of required

shade:

50.114.66.1

Old work (Two or more coats applied @ 1.67 ltr/ 10 sqm) on

existing cement paint surface Sqm 24496

5113.60

Wall painting with plasters emulsion paint of approved brand and

manufacturer to gve an even shade.

Page 10 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

51.113.60.1 one or more coats on old work

Sqm 17359.7

52

14.1

Repairs to plaster of thickness 12 mm to 20 mm in patches of area

2.5 sq meters and under, including cutting the patch in proper

shape, raking out joints and preparing and plastering the surface of

the walls complete, including disposal of rubbish to the

52.114.1.1 With cement mortar 1:4 (1 cement : 4 fine sand)

Sqm 150

5314.6 Renewing glass panes, with wooden fillets wherever necessary :

53.114.6.1 Float glass panes of thickness 4 mm

Sqm 20

54

14.12

Providing and fixing 16 mm M.S. Fan clamps of standard shape and

size in existing R.C.C. slab, including cutting chase, anchoring

clamp to reinforcement bar, including cleaning, refilling, making

good the chase with matching concrete, plastering and paintEach 4

55 14.42 White washing with lime to give an even shade:

55.114.42.2 old work ( two or more coats)

Sqm 10

56

14.46

Removing dry or oil bound distemper, water proofing cement paint

and the like by scrapping, sand papering and preparing the surface

smooth including necessary repairs to scratches etc. complete.Sqm 15000

5714.45

Distempering with oil bound washable distemper of approved

brand and manufacture to give an even shade:

57.114.45.1 Old work (one or more coats)

Sqm 17420.5

5814.54

Painting with synthetic enamel paint of approved brand and

manufacture of required colour to give an even shade:

58.114.54.1 One or more coats on old work

Sqm 5414

5913.63

Painting with aluminium paint of approved brand and manufacture

to give an even shade

Page 11 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

59.113.63.1 Two or more coats on new work

Sqm 20

60

14.72

Providing and fixing double scaffolding system (cup lock type) on

the exterior side, up to seven story height made with 40 mm dia

M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining

with cup & lock system with M.S. tubes, M.S. tube challies, M.S.

clamps and M.S. staircase system in the scaffolding for working

platform etc. and maintaining it in a serviceable condition for the

required duration as approved and removing it there after .The

scaffolding system shall be stiffened with bracings, runners,

connection with the building etc wherever required for inspection

of work at required locations with essential safety features for the

workmen etc. complete as per directions and approval of

Engineerin- charge .The elevational area of the scaffolding shall be

measured for payment purpose .The payment will be made once

irrespective

of duration of scaffolding

Sqm 50

61

15.3

Demolishing R.C.C. work manually / by mechanical means

including stacking of steel bars and disposal of unserviceable

material within 50 metres lead as per direction of Engineer-in-

Charge. (as per qty 5.1.3) Cum 2

62

15.60

Disposal of building rubbish / malba / similar unserviceable,

dismantled or waste materials by mechanical means, including

loading, transporting, unloading to approved municipal dumping

ground or as approved by Engineer-in-charge, beyond 50 m initial

lead Cum 215.29

63

15.7

Demolishing brick work manually / by mechanical means including

stacking of serviceable material and disposal of unserviceable

material within 50 metres lead as per direction of Engineer-in-

Charge. 63.1 15.7.4 In cement mortar Cum 2

64

15.13Taking out doors, windows and clerestory window shutters (steel or

wood) including stacking within 50 metres lead:

Page 12 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

64.115.13.1 Of area 3 sq. metres and below

Sqm 20

6515.23

Dismantling tile work in floors and roofs laid in cement mortar

including stacking material within 50 metres lead.

65.115.23.2 For thickness of tiles above 25 mm and up to 40 mm

Sqm 900

66

17.1

Providing and fixing water closet squatting pan (Indian type W.C.

pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level

white P.V.C. flushing cistern, including flush pipe, manually

controlled device (handle lever) conforming to IS : 7231, with

66.117.1.1

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

with integral type foot rests Each 40

67

17.2

Providing and fixing white vitreous china pedestal type water closet

(European type W.C. pan) with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with manually

controlled device (handle lever), conforming to IS : 723

67.117.2.1 W.C. pan with ISI marked white solid plastic seat and lid

Each 30

68

17.23

Providing and fixing white vitrus china flat back or wall corner type

lipped front urinal basin of 430 x 260x 350 mm or 340 x 410 x 265

mm sizes respectively Each 20

6917.24

Providing and fixing white vitreous china squatting plate urinal

with integral rim longitudinal flush pipe. Each 5

70

17.7

Providing and fixing wash basin with C.I. brackets, 15 mm C.P.

brass pillar taps,32 mm C.P. brass waste of standard pattern,

including painting of fittings and brackets, cutting and making

good the walls wherever require:

70.117.7.1

White Vitreous China Wash basin size 630x450 mm with a pair of

15 mm C. P. brass pillar taps Each 50

71

17.10

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as

per IS 13983 with C.I. brackets and stainless steel plug 40 mm,

including painting of fittings and brackets, cutting and making

good the walls wherever required:

Page 13 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

71.1 17.10.2 Kitchen sink without drain board

71.1.117.10.2.1 610x510 mm bowl depth 200 mm (without drain board)

Each 45

7217.28

Providing and fixing P.V.C. waste pipe for sink or wash basin

including PVC. waste fittings complete. 72.1 17.28.2 Flexible pipe

72.1.117.28.2.1 Flexible pipe - 32 mm dia

Each 50

73

17.31

Providing and fixing 600x450 mm beveled edge mirror of superior

glass (of approved quality) complete with 6 mm thick hard board

ground fixed to wooden cleats with C.P. brass screws and washers

complete. Each 30

7417.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

74.1

17.70.2

Bottle trap 38 mm single piece moulded with height of 270 mm,

effective length of tail pipe 260 mm from the centre of the waste

coupling, 77 mm breadth with 25 mm minimum water seal,

weighing not less than 263 gms Each 40

75

18.7

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings including fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of p

75.1.118.7.2 20mm nominal outer dia pipes

Mtr 350

75.1.218.7.3 25 mm nominal outer dia pipes

Mtr 200

75.1.318.7.5 40 mm nominal outer dia Pipes

Mtr 200


Mtr 200

Page 14 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

76

18.9


having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings This includes jointing of pipes

& fittings with one step CPVC solvent cement ,trenching ,refilling

& testing of joints complete as per direction of Engineer in Charge.

76.118.9.7 62.50 mm nominal outer dia Pipes

Mtr 40


Mtr 60

77

18.8


having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings i/c fixing the pipe with clamps

at 1.00 m spacing. This includes jointing of pipes &

77.1

18.8.2 20 mm nominal outer dia pipes

Mtr 200

78

18.10

Providing and fixing G.I. pipes complete with G.I. fittings and

clamps, including cutting and making good the walls etc.

Internal work - Exposed on wall

78.1

18.10.3 25 mm dia nominal bore

Mtr 10

78.1.1


Mtr 10

78.1.2


Mtr 10

78.1.3


Mtr 10

Page 15 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

79

18.12

Providing and fixing G.I. pipes complete with G.I. fittings including

trenching and refilling etc.

External work

79.1


Mtr 20

79.1.2


Mtr 20

79.1.3


Mtr 20

79.1.4


Mtr 20

79.1.5


Mtr 20

79.1.6


Mtr 20

8018.18

Providing and fixing ball valve (brass) of approved quality, High or

low pressure, with plastic floats complete:

80.1

18.18.3 25 mm nominal bore

Each 100

81

18.47

Providing and fixing G.I. Union in existing G.I. pipe line, cutting

and threading the pipe and making long screws, including

excavation, refilling the earth or cutting of wall and making good

the same complete wherever required:

81.1


Each 10

81.1.1


Each 10

Page 16 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

81.1.2


Each 10

81.1.3


Each 10

81.1.4


Each 10

81.1.5


Each 5

83

19.1

Providing, laying and jointing glazed stoneware pipes class SP-1

with stiff mixture of cement mortar in the proportion of 1:1 (1

cement : 1 fine sand) including testing of joints etc. complete:

83.1

19.1.1 100 mm diameter

Mtr 200

83.1.1

19.1.3 200 mm diameter

Mtr 50

84

19.2

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

sand : 10 graded stone aggregate 40 mm nominal size) all-round

S.W. pipes including bed concrete as per standard design:

84.1

19.2.1 100 mm diameter S.W. pipe

Mtr 40

84.1.1

19.2.3 200 mm diameter S.W.Pipes

Mtr 50

85

19.5

Dismantling of old S.W. pipes including breaking of joints and bed

concrete stacking of useful materials near the site within 50 m lead

and disposal of unserviceable materials into municipal dumps:

Page 17 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

85.119.5.1 100 mm diameter

Mtr 200

85.1.119.5.3 200 mm diameter 19.1.3

Mtr 50

86

19.7

Constructing brick masonry manhole in cement mortar 1:4 ( 1

cement : 4

coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2

coarse

sand : 4 graded stone aggregate 20 mm nominal size), foundation

concrete

1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40

mm

nominal size), inside plastering 12 mm thick with cement mortar

1:3 (1

cement : 3 coarse sand) finished with floating coat of neat cement

and

making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand :

4 graded stone aggregate 20 mm nominal size) finished with a

floating coat

of neat cement complete as per standard design

86.1

19.7.2

Inside size 120x90 cm and 90 cm deep including C.I. cover with

frame (heavy duty) 500 mm internal diameter, total weight of

cover and frame to be not less than 116 kg (weight of cover 58

kg and weight of frame 58 kg) :

86.1.119.7.2.1 With FPS bricks class designation 7.5.

Each 9

88 19.8 Extra for depth for manholes

88.1 19.8.2 Size 120x80 cm

88.1.119.8.2.1

With common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 RM 3

Page 18 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

89

21.1

Providing and fixing aluminium work for doors, windows,

ventilators and partitions with extruded built up standard tubular

sections/ appropriate Z sections and other sections of approved

make conforming to IS: 733 and IS: 1285, fixing with dash fasteners

89.1 21.1.1 For fixed portion

89.1.2

21.1.1.1

Anodised aluminium (anodised transparent or dyed to required

shade according to IS: 1868, Minimum anodic coating of grade AC

15) Kgs 105

90

21.1.2

For shutters of doors, windows & ventilators including providing

and fixing hinges / pivots and making provision for fixing of fittings

wherever required including the cost of EPDM rubber / neoprene

gasket required (Fittings shall be paid for separately).

90.1

21.1.2.1

Anodised aluminium (anodised transparent or dyed to required

shade according to IS: 1868, Minimum anodic coating of grade AC

15) Kgs 90

91

21.2

Providing and fixing 12 mm thick prelaminated particle board flat

pressed three layer or graded wood particle board conforming to IS:

12823 Grade I Type II, in panelling fixed in aluminum doors,

windows shutters and partition frames with C.P. brass / stainless

steel screws etc. complete as per architectural drawings and

directions of Engineer-in-Charge.

91.121.2.1

Pre-laminated particle board with decorative lamination on one

side and balancing lamination on other side Sqm 6

92

21.3

Providing and fixing glazing in aluminium door, window,

ventilator shutters and partitions etc. with EPDM rubber / neoprene

gasket etc. complete as per the architectural drawings and the

directions of Engineer-in-Charge. (Cost of aluminium snap beading

sh

92.121.3.2 With float glass panes of 5.50 mm thickness

Sqm 6

Page 19 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

93

22.2

Providing and laying APP (Atactic Polypropylene Polymer)

modified prefabricated five layer 3 mm thick water proofing

membrane, black finished reinforced with non-woven polyester

matt consisting of a coat of bitumen primer for bitumen membrane

@ 0.40 litre / sqm by the same membrane manufacture of density at

25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer

coat the layer of membrane shall be laid using Butane Torch and

sealing all joints etc., and preparing the surface complete. The vital

physical and chemical parameters of the membrane shall be as

under : Joint strength in longitudinal and transverse direction at

23°C as 650/450N/5 cm. Tear strength in longitudinal and

transverse direction as 300/250N. Softening point of membrane not

less than 150°C. Cold flexibility shall be upto -2°C when tested in

accordance with ASTM, D - 5147. The laying of membrane shall be

got done through the authorised applicator of the Manufacturer of

membrane :

93.122.20.1 3 mm thick

Sqm 50

94

22.5

Providing and laying water proofing treatment in sunken portion

of WCs, bathroom etc., by applying cement slurry mixed with

water proofing cement compound consisting of applying : a) First

layer of slurry of cement @ 0.488 kg /sqm mixed with water proofinSqm 25

95

23.1

Boring/drilling bore well of required dia for casing/ strainer pipe, by

suitable method prescribed in IS: 2800 (part I), including collecting

samples from different strata, preparing and submitting strata

chart/ bore log, including hire & running charges of all equipments,

tools, plants & machineries required for the job, all complete as per

direction of Engineer -in-charge, upto 90 metre depth below

ground level.

95.123.1.1.1 300 mm dia

Mtr 100

Page 20 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

96

23.2

Boring/drilling bore well of required dia for casing/ strainer pipe, by

suitable method prescribed in IS: 2800 (part I), including collecting

samples from different strata, preparing and submitting strata

chart/ bore log, including hire & running charges of all equipments,

tools, plants & machineries required for the job, all complete as per

direction of Engineer -in-charge, beyond 90 metre & upto 150

metre depth below ground level.

96.123.2.1.1 300 mm dia

Mtr 100

97

23.3

Supplying, assembling, lowering and fixing in vertical position in

bore well, unplasticized PVC medium well casing (CM) pipe of

required dia, conforming to IS: 12818, including required hire and

labour charges, fittings & accessories etc. all complete, for all

depths, as per direction of Engineer -in-charge.

97.123.3.3 200 mm nominal size dia (For Dispensaries where ever required)

Mtr 100

98

23.4

Supplying, assembling, lowering and fixing in vertical position in

bore well unplasticized PVC medium well screen (RMS) pipes with

ribs, conforming to IS: 12818, including hire & labour charges,

fittings

& accessories etc. all complete, for all depths, as per direction of

Engineer-in-charge.

98.123.4.3 200 mm nominal size dia(For Dispensaries where ever required)

Mtr 100

991214 Welding by gas plant

cm 1

1001215 Welding by electric plant

cm 1

1011366 CI Grating 150x150mm

Each 20

1021927

Supply of brass way valve with C.I. wheel of approved quality

(screwed end) 25mm dia: Each 20

Page 21 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

1031928


(screwed end) 32 mm dia: Each 2

1041929



1051930



1061931



1071932



1087257 Supply of CP Brass bib cock 15mm dia

Each 150

1097259 Supply of CP Brass long body bib cock 15mm dia

Each 50

1107260 Supply of CP Brass stop cock 15mm dia

Each 50

1117261 Supply of C.P. Brass angle valve 15 mm

Each 100

112

DSR

Labour

rates

Labour charges for maintaining day to day maintenance works at

Offices, Dispensaries and residential quarters and attending to

repairs with the maintenance staff with all helpers, tools and plants

as directed the Engineer-in-charge as below :

0122 Plumber 4 NosMonth 48

0115 Plumber Helper 4 NosMonth 48

0122 Sewerman 4 NosMonth 36

0115 Sewerman Helper 4 NosMonth 36

0111 Carpenter 1 NoMonth 12

115 Carpenter Helper 1 NoMonth 12

Page 22 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

122 Mason 1 NoMonth 12

115 Mason Helper 1 NoMonth 12

MR SupervisorMonth 12

113 120 Suppying and fixing of gun metal check valve

120 (vi) 20mmEach 1

120 (v) 25mmEach 1

120 (iv) 32mmEach 1

120 (iii) 40mmEach 1

120 (ii) 50mmEach 1

120 (i) 65mmEach 1

114 SSR 119 Supplying and fixing of GI Tee

D-VI 15mm diaEach 1

D-V 20mm diaEach 1

D-IV 25mm diaEach 1

D-III 32mm diaEach 1

D-II 40mm dia Each 1

D-I 50mm dia Each 1

115 SSR 119 Supplying and fixing GI Bend

C-VI 15mm Each 1

Page 23 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

C-V 20mmEach 1

C-IV 25mm Each 1

C-III 32mmEach 1

C-II 40mm dia Each 1

C-I 50mm dia Each 1

116 SSR 119 Supplying and fixing GI elbow

B-IV 15mm dia Each 1

B-V 20mm diaEach 1

B-IV 25mm dia Each 1

B-III 32mm dia Each 1

B-II 40mm dia Each 1

B-I 50mm dia Each 1

117 SSR 119 Supplying and fixing reducer

F-I 50x40mm diaEach 1

F-II 40x32mm diaEach 1

F-III 32x25mm diaEach 1

F-IV 25x20mm diaEach 1

118 SSR 119 Supplying and fixing of hex nipple

Page 24 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

I-I 50 mm diaEach 1

I-II 40 mm diaEach 1

I-III 32 mm dia Each 1

I-IV 25 mm dia Each 1

I-V 20 mm dia Each 1

I-VI 15 mm diaEach 1

119

SSR

143/P51

Supply and Fixing of C.I Nahani / Floor trap with Stainless Steel

grating 100 x 75 mm Each 25

120MR Jaquar make continental series code no. 037 bibcock

Each 20

121MR Jaquar make continental series code no. 053 angular cock

Each 20

122MR Jaquar make continental series Bottle Trap

Each 20

123

MR

Cleaning of septic tanks, manholes, pipe lines by pumping

out/removal of the sludge and sewage with mechanically operated

vaccum based septic tank cleaner including disposal of sludge far

away from the ESIC campus by mechanical transporation using

covered tanks without disturbing the public life etc. complete as per

the direction of the Engineer-in-charge. Cum 651.2

124

MRCleaning the storm water drain around the office campus by using

necessary tools and plants as directed etc. complete.Mtr 400

125

MR

Cleaning the over head tank of various sizes in terrace by using

pressure air jet method, with required detergent etc. complete (3

times) Liter 16000

Page 25 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

126

MRCleaning the over head tank of higher capacity by using pressure

air jet method, with required staging detergent etc. complete Liter 800000

127

MRCleaning the under ground sump of various sizes by pressure air jet

method with required detergents etc. completeLiter 400000

128

MR

Providing and fixing square-mouth S.W. gully trap grade 'A'' water

tight of 300x300mm : 100x100 mm size P type With F.P.S. Bricks

class designation 75 Each 20

129

MR

Providing and fixing fly proof wire gauze mesh to windows using

Saint-Gobian wire gauze With 2nd class teak wood beading alround

of 40x19 mm etc. complete as per the directions of Engineer-in-

Charge Sqm 50

130

MR

Pressure grouting to concrete members after making 12mm dia.

holes with power drill and fixing PVC nozzles in the hole made

with cement paste and dry for one day to set hard for injecting the

grouting compound i.e. void seal of M/S Pegasas or CEBEX 100 of

M/S Fosroc or Equivalent mixed with cement and wtaer.. The void

seal or Fosroc chemical compound to be added @ 125 gm per bag of

cement and mixed with water to make slurry ready to inject. The

prepared grouting compound to be injected with grouting

equipment at 140 psi pressure and cutting the PVC nozzles, sealing

holes and making good all the treated area etc. complete as per the

directions of Engineer-in-Charge Pt 10

131

MR

Removing loose concrete cover and cleaning the damaged RCC

portion such as beams, slabs, RCC wall, applying rust remover,

rusticide, Dr,fixit, Pidilite propduct or, equavalent, allow 24 hrs

time, apply chemical Zinchromite, Zincovit to harden the loose

portion, apply cement mortor 1:3 with nice sand adding super latex

at mixture neatly over the affected surface for finishing and allow

time 24 hours etc complete Sqm 10

132

MR

Relaying Cuddapah slab for cupboard slabs and medai etc.

including pointing with cement mortar 1:3 to the full depth of slab

etc. complete. Sqm 70.88

Page 26 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

133

MR

Providing Horticulture works with the specification ; 1. Clearing the

ground surface. 2.Fine dressing the ground. 3.Ternching the ground

by 30 to 40 C, earth filling with good earth including transport

charges 4. Uprooting the weeds and dispossing of from the site 5.

Supplying of mannure and seldge at site and mixing the same in the

ratio of 2 parts of earth to 1 part of mannure an spreding throughly

including necessary transporting charges and lift charges & planting

hedges and shurbs including watering and maintaining for a period

of 6 months Sqm 20

134MR

Supplying and fixing of Vertical blind of good quality as approved

by Enignner incharge for Windows Sqm 20

135MR Supplying and providing PVC Lids for Water storage tanks

Each 25

136MR

Supplying and providing Good quality of Steel Cupoard with

drawer arrangment for counters. Each 5

137MR Water meter (including testing charges) 80 mm

Each 1

138MR Water meter (including testing charges) 100mm

Each 1

139

MR

Provision for cleaning the sewage pump room wells using with

tripod, stand, pully, chain block, bucket coir split bamboos and

spurn yarn including removing the deposited silt and sediments

depositing in one place and convey away from the site as directed

by the departmental officers. Job 2

140

M.R

Repairs to Kulatheri main pipe line Removing existing pipe

line,aresting the leakages with required new pipe, specials, earth

work, dewatering, packing, packing materials, concrete cutting,

threading, shellac, thread ball, etc.,Job 2

Page 27 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

.

1.8

Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FR PVC insulated copper conductor single core

cable in surface / recessed medium class PVC conduit, with piano

type switch, phenolic laminated sheet, suitable size M.S. box and

earthing the point with 1.5 sq.mm. FR PVC insulated copper

conductor single core cable etc as required.

141.11.8.2 Group B

Point 341

142

1.9

Wiring for twin control light point with 1.5 sq.mm FR PVC

insulated copper conductor single core cable in surface / recessed

medium class PVC conduit, 2 way piano type switch, phenolic

laminated sheet, suitable size MS box and earthing the point with

1.5 sq.mm. FR PVC insulated copper conductor single core cable etc

as required. Point 100

142

1.11

Wiring for twin control light point with 1.5 sq.mm FR PVC

insulated copper conductor single core cable in surface / recessed

medium class PVC conduit, 2 way modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm. FR PVC

insulated copper conductor single core cable etc as required.Point 7

143

1.10

Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor single core

cable in surface / recessed medium class PVC conduit, with modular

switch, modular plate, suitable GI box and earthing the point with

1.5 sq.mm. FRLS PVC insulated copper conductor single core cable

etc. as required.

143.1 1.10.2 Group B Point 272

144

1.12

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated

copper conductor single core cable in surface/ recessed medium

class PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated

copper conductor single core cable for loop earthing as required.Mtr 1650

Page 28 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

145

1.13

Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated

copper conductor single core cable in surface/ recessed medium

class PVC conduit alongwith 2 Nos 4 sq. mm FR PVC insulated

copper conductor single core cable for loop earthing as required.Mtr 75

146

1.14

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FR PVC insulated copper conductor, single core

cable in surface/ recessed medium class PVC conduit as required

146.11.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Mtr 1650

146.21.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Mtr 2150

146.31.14.8 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Mtr 250

146.41.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Mtr 230

147

1.17

Supplying and drawing following sizes of FRLS PVC insulated

copper conductor, single core cable in the existing surface recessed

steel / PVC conduit as required

147.11.17.1 1 x 1.5 sq.mm

Mtr 10

147.21.17.11 2 x 2.5 sq.mm

Mtr 10

147.81.17.20 2 x 4 sq.mm

Mtr 10

148

1.18

Supplying and drawing following pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored telephone cable

in the existing surface / recessed steel / PVC conduit as required

148.11.18.1 1 pair

Mtr 10

148.21.18.2 2 pair

Mtr 10

148.31.18.3 4 pair

Mtr 10

Page 29 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

149

1.19

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the existing surface

recessed steel / PVC conduit as requiredMtr 20

150

1.21

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface / recess including cutting

the wall and making good the same in case of recessed conduit as

required

150.11.21.1 20 mm

Mtr 50

150.21.21.2 25 mm

Mtr 50

151

1.23Supplying and fixing following piano type switch/ socket on the

existing switch box/ cover including connections etc. as required.

151.11.23.1 5/6 amps switch

Each 185

151.21.23.2 2 way 5/6 amps switch

Each 30

151.31.23.3 15/16 amp switch

Each 95

151.41.23.4 3 pin 5/6 amp socket outlet

Each 95


Each 55

151.61.23.8 Bell bush

Each 42

152

1.24

Supplying and fixing following modular switch/ socket on the

existing modular plate & switch box including connections but

excluding modular plate etc. as required.

152.11.24.1 5/6 amps switch

Each 190

152.21.24.3 15/16 amp switch

Each 55


Each 190

Page 30 of 40

In Figures In Words

Item

No

DSR Item


RateTotal


Each 95

152.51.24.8 Bell push

Each 11

153

1.25

Supplying and fixing stepped type electronic fan regulator on the

existing modular plate switch box including connections but

excluding modular plate etc. as required. Each 100

154

1.26Supplying and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as required.Each 155

155

1.27

Supplying and fixing following size/ modules, GI box alongwith

modular base & cover plate for modular switches in recess etc as

required.

155.11.27.1 1 or 2 Module (75mmX75mm)

Each 200

155.21.27.2 3 Module (100mmX75mm)

Each 226

155.31.27.3 4 Module (125mmX75mm)

Each 250

155.41.27.4 6 Module (200mmX75mm)

Each 110

155.51.27.5 8 Module (125mmX125mm)

Each 73

156.61.27.6 12 Module (200mmX150mm)

Each 58

1561.28

Supplying and fixing following modular base and cover plate on

existing modular metal box etc. as required.

156.11.28.1 1 or 2 Module

Each 190

156.21.28.2 3 Module

Each 190

156.31.28.3 4 module

Each 190

Page 31 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

156.41.28.4 6 module

Each 190

156.51.28.5 8 module

Each 190

156.61.28.6 12 module

Each 190

157

1.31

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing

3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch,

connection etc. as required. (For light plugs to be used in non

residential buildings). Each 170

158

1.32

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing

6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps

modular switch, connection etc. as required.Each 93

1591.38

Supplying and fixing call bell/ buzzer suitable for single phase, 230

volts, complete as required. Each 16

1601.53

Supplying and drawing of UTP 4 pair CAT 6 Lan cable in existing

surface / recessed steel / PVC conduit as required Mtr 300

161

2.18

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket

outlet, with 2 pole and earth, metal enclosed plug top alongwith 20

amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in

recess, with chained metal cover for the socket out let and complete

with connections, testing and commissioning etc. as required.Each 43

162

5.2

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including

accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. with charcoal/

coke and salt as required. Each 25

163

7.1

Laying of one number PVC insulated and PVC sheathed / XLPE

power cable of 1.1 KV grade of following size direct in ground

including excavation, sand cushioning, protective covering and

refiiling the trench etc as required

Page 32 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

163.17.1.1 Upto 35 sqmm

Mtr 50

163.27.1.2 Above 35 sqmm and Upto 95 sqmm

Mtr 50

163.32904 8 SWG copper wire (4.0 mm dia)

kg 38

164

9.1

Supplying and making end termination with brass compression

gland and aluminium lugs for following size of PVC insulated and

PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade

as required.

164.19.1.2 2 X 10 sq. mm (19mm)

Each 30

164.29.1.4 2x25 Sqmm

Each 8

164.39.1.7 3 x 10 Smm

Each 5

1651101

1.5 sq. mm ISI marked, FR PVC insulated, single core copper

conductor cable Mtr 50

1661102



1671103



1681104



1691110

32/0.20mm (1 sqmm) twin circular FRLS PVC sheathed, workshop

flexible copper cable Mtr 50

170 1436 Bell push, piano type Each 50

1711706

6 amps. to 32 amps. ratings , SP MCB, "C" curve, 10 KA breaking

capacity Each 150

1721708

6 amps. to 32 amps. ratings , DP MCB, "C" curve, 10 KA breaking

capacity Each 50

1731709

6 amps. to 32 amps. ratings , TP MCB, "C" curve, 10 KA breaking

capacity Each 14

Page 33 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

1741712 40 amps., 2 pole isolator

Each 50

1751740 12 way SPN Double door MCB DB

Each 20

176

2.12

Supplying and fixing following rating, double pole, 240 volts,

isolator in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

1762.12.1 40 Amps

Each 25

1772.12.2 63 amps

Each 20

178

2.13

Supplying and fixing following rating, four pole, 415 volts, isolator

in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

1782.13.1 40 Amps

Each 10

1792.13.2 63 amps

Each 20

1802.13.3 100 amps

Each 13

181

2.3

Supplying and fixing following way, single pole and neutral, sheet

steel, MCB distribution board, 240 volts, on surface/ recess complete

with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including arthing etc. as required.

(But without MCB/RCCB/Isolator)

181.12.3.1 2 + 4 way/ 6 way , Double door

Each 2

1822.3.2 2 + 6 way/ 8 way , Double door

Each 20

1832.3.3 2 + 10 way/ 12 way , Double door

Each 2

1842.3.4 2 + 14 way / 16 way, Double door

Each 10

Page 34 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

185

2.4

Supplying and fixing following way, horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 volts, on surface/

recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/Isolator)

2.4.4 4 way (4 + 12), Double doorEach 2

186

11.3

Erection of metallic pole of following length in cement concrete


nominal size) foundation including excavation and refilling etc. as

required.

11.3.1 Above 4.5 mtr and upto 6.5 mtrEach 25

188

1.17

Supplying and drawing following sizes of FRLS PVC insulated

copper conductor, single core cable in the existing surface/ recessed

steel/ PVC conduit as required.

1891.17.21 3 x 4 sq. mm

Mtr 25

1891.17.30 3 x 6 sqmm

Mtr 25

1911442 Brass batten/ angle holder

Each 50

192

Labour charges for day to day maintenance works at Hospital, Staff

Quarters and 3 dispensaries, staff quarters and attending to repairs

round the clock with maintenance staff with all helpers, tools, as

directed by the Engineer in charge.

1004 Electrician Grade I - 5 NosMonth 60

1005 Electrician Grade II- 5 NosMonth 60

Page 35 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

1004 Pump Driver- 2 NosMonth 24

1004 Lift Operator- 4 NosMonth 60

MR Supervisor "C" License HolderMonth 12

193

SD-125

Supply and fixing of TNEB meter Board suitable for 32A Single

Phase service connection with 32A Fuse unit (500V) 32A neutral

link and earth link (1" x 1/8" Copper flat) on TW plank of size

375mm x 300mm x 19mm with supporting TW reepers of 1" thick

an either side with painting with suitable bolt and nuts for fixing

the TW plank on wall with earth connection and inter connection

with 7/20 PVC insulated copper wire from EB meter to fuse unitEach 5

194

SD -127

Supply and fixing of TNEB meter Board suitable for 32A Three

Phase service connection with 3 Nos. 32A Fuse unit (500V) 32A

neutral link and earth link (1" x 1/8" Copper flat) on TW plank of

size 600mm x 450mm x 19mm with supporting TW reepers of 1"

thick an either side with painting with suitable bolt and nuts for

fixing the TW plank on wall with earth connection and inter

connection with 7/20 PVC insulated copper wire from EB meter to

fuse unit. Each 5

195

SD - 198

Supply and laying of 2x10 Sqmm PVC armoured LT UG Cable in a

trench to be excavated at a depth of 0.75 mtr putting 0.15 mtr layer

of sand and covering the cable completely with bricks and sand and

refiiling the earth to make goodMtr 460

196

SD-200

Supply and laying of 2x25 Sqmm PVC armoured LT UG Cable in a

trench to be excavated at a depth of 0.75 mtr putting 0.15 mtr layer

of sand and covering the cable completely with bricks and sand and

refiiling the earth to make goodMtr 1200

Page 36 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

197

SD 88

Supply and fixing of single box type 4'40 W flu fitting complete

with copper choke and condensor with TW round blocks on wall or

ceiling with flu tube with PVC unsheathed copper leads from

terminals to the fitting. Each 90

198B.1.a

A.C. ceiling fan complete 1200mm ( 48") sweep with 300mm down

rod (without regulator) ( crompton make) Each 110

199

SD 114

Supply and fixing of 300 mm ( 12" ) sweep (light duty) AC exhaust

fan complete with necessary wall opening and making good the

wall. Each 26

200 A-15 Polyster filled copper choke 250 V/50 Hz grade suitable

c 36/40 W Electronic ballast for flu typeEach 90

201 A-4 Fluorescent tubular lamps with ISI mark

b Cool day light 4 ft 40 Watts Each 340

202A-14-b Starter for flu tube 40 Watts

Each 180

203C.2.b 32AmpsDP switch with metal clad ( Front handle )

Each 7

204C.3.a 100 Amps TPN switch with HRC fuces sheet steel double break.

Each 7

205B.5.b 32 Amps porcelein fuce unit ( 500 V)

Each 7

206B.5.c 63 Amps porcelein fuce unit ( 500 V)

Each 16

207B.5.d 100 Amps porcelein fuce unit ( 500 V)

Each 16

208A.3.d 36Watts CFL Bulb

Each 100

209A.3.c 18Watts CFL Bulb

Each 100

Page 37 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

210J.1.a T.W Box conceiled type 12" x 8" x 3"

Each 70

211J.1.b T.W Box conceiled type 8" x 6" x 3"

Each 35

212J.1.c T.W Box conceiled type 6" x 4" x 3"

Each 60

213J.1.d T.W Box conceiled type 4" x 4" x 3"

Each 30

214I.8.a Insulation Tape roll

Each 60

215

SD 36

Wiring with 2 x 1.5 swmm ( 22/0.3) PVC insulated SC unsheathed

Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall

and ceiling with PVC accessories with 150 x 100 x 113 mm TW

switch box for 5 A 3 pin non inter locking CS plug with painting of

suitable colour with continious earth wire connection of 14 SWG TC

wire for open PVC plug point.Point 60

216

SD 39

Wiring with 2 x 4 sqmm (56/0.3 ) PVC insulated SC unsheathed Cu.

Conductor of 1100 V grade in suitable PVC rigid pipe conceiled in

wall and ceiling with PVC accessories. In flush with wall, with

150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem

sheet cover for 5 A 3 pin non inter locking CS plug with continious

earth wire connection of 14 SWG TC wire and making good of the

consealed portion with suitable colour for concealed PVC plug

point. Point 30

Total of SSR Items

217DATA

Supplying and fixing of 2 x 36 W CFL Street light fitting with 36W

CFL Each 50

218MR Supply of 400mm sweep wall bracket fan with push button switch

Each 25

219MR Supply of 2.5 MFD Fan condensor

Each 60

Page 38 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

220MR 400mm sweep pedestral fan

Each 8

221MR EBT2 18 W Choke

Each 80

222MR EBT 236 TLD 36W Choke

Each 40

223MR

Annual Maintenance to 1.5/2 ton window model/ Split type Air

Condition. Each 156

224MR

Charges for Breake down and Gas Charging to 1.5/2 ton window

model/ Split type Air Condition Unit. Kg 20

225MR Capacitor

Each 20

226

MR

GEM make starter (New) Panel with star delta starter, single phase

preventor, 4 pole MCB in corner / volt meter, pilot lamp with

switch complete with sheet steel enclosure and internal and earth

connections. Each 3

227MR Texmo 15 stage submersible pump.(15 Hp Bore well 250 ft depth)

Each 1

228MR Repairing of starter pannel including spares.

Each 4

229MR Repairing Various HP motor and rewinding including spares

a 5 - 7.5 HPEach 4

b 10 - 15HP Each 2

230MR

Monthly maintenance of 2000 KVA 440 V Diesel Generator

(caterpillar make) ( 1 No) Each 1

231MR Engine oil

Ltr 150

232MR Charges for supply of Oil filter

Each 10

233MR Charges for supply of Diesel filter

Each 10

234MR Charges for supply of Radiator coolent

ltr 20

Page 39 of 40

In Figures In Words

Item

No

DSR Item


RateTotal

235MR Charges for supply of distilled Water.

Ltr 20

236MR Supply of diesel for 2000 KVA DG Set

Ltr 18000

237MR OCB Servicing

Each 2

238MR 4 KVA Stabilizer

Each 3

239 MR Supply of following chemicals for the RO plant

a Sodium Metabi SulphiteKg 432

b Anti scalentLtr 432

TOTAL

Page 40 of 40

Documents

ANNUAL REPAIR AND MAINTENANCE OF (CIVIL …esichennai.org/rochennai/Financial Bid-170317.pdfHalf brick masonry with common burnt clay F.P.S ... universal hydraulic door closer (having