)PCS t

1s1

2nd3rd

Alkyd Primer /Red OxidePrimer QDPilot ll

Pilot ll

40

4040

Alkyd Prlmer

Alkyd GlosAlkyd Gloss

St 3 or 5a ZtpSteel Exposed toMild Environment 5-14

Alkyd Primer does not contenlzinc chromate or red leadwhich is health hazardous.Better surface preparation willensure better performance.

\

{--)e,ru|)r

#\s

JPCS 2

1st

2nd

3rd

or3rd

Jotaguard 82

Jotaguard 82

PenguardTopcoat

Hardtop AS /Hardtop XP

100

100

50

50

GeneralPurpose EpoxyGeneralPurpose EpoxyEpoxy GlossTopcoat

AliphaticPolyurethane

5t 3 or Sa 2rrz

For steelworkexposed to mild andmoderate corrosivityenvironment

8-17

It is a natural characteristic forPenguard Topcoat epoxy glossto chalk when exposed toultra-violet, HardtopAS/Hardtop XP should beadopted for better weather;ngresistance.

JPCS 3

1st

lnd3rd

lotaguard 82

Plot llPlot ll

100

4040

General PurposeEpoxyAlkyd Gloss FinishAlkyd Gloss Finish

St 3 or Sa 21aFor steelwork exposedto mild and moderatecorrosivity environment

8- 10

Topcoating Jotaguard 82 withPilot ll will help to improveweatherrng resistance of thesystem,however chemicalresistance of the system dependlargely on Jotaguard 82

JPCS 4

1st

2nd

3rd

or3rd

Jotamastic 80

Jotamastic 80

PenguardTopcoat

Hardtop AS /Hardlop XP

7E

75

50

50

SuriaceTolerant EpoxySurfaceTolerant EpoxyEpoxy GlossTopcoat

AliphaticPolyurethane

5t 3 or 5a 2irzSteel Exposed toMild and ModerateCorrosivity Environment

8- 12

It is a natural characteristicfor Penguard Topcoat epoxygloss to chalk when exposedUV, Hardtop As/Hardtop XPshould be adopted for betterweathering resistance.

JPCS 5

*l

lst

2nd

3rd

or3rd

Bar(ier ZP /Sarrier 77PenguardExpressFenguardTopcoat

Hardtop AS /Hardtop XP

65

175

50

50

€poxy Zinc Pn'mer

Fast Drying Epoxy

Epoxy GlossTopcoat

AliphaticPolyurethane

Sa2ln Moderate to HighCorrosivity Environment 10-15

Zinc based coating are notrecommended for high alkalineand acidic environment as thesemay further speed up larlureSPreactrvrty ot zrnc.

lb9,^ lE'J_-

JPCS 6

I St

2nd3rd

E?Eflch

Pilot ll

Pilot ll

-1A

4040

ffiffrffiepo;--f-Etch PrimerAlkyd GlossAlkyd Gloss

ContaminantFree

Galvanised, Stainlesssteel, Aluminrum &Mild steel

5- 10

.v tz_tThickness of JotaEtch shJltEA.

il'i[lfii:].i' ts m cr\Q

JPCS 7

1st

2nd

3rd

lotaEtch

PenguardExpressHardtop As/Hardtop xP

10

75

50

Modiiied EpoxyEtch PrimerFast Drying Epoxy

AliphaticPolyurethane

ContaminanlFree

Galvanised, Stainlesssteel ,Aluminium &Mild steel

8- 10Thickness of JotaEtch shall bemaintained at 10-15 micronsto avoid failure.

JPCS 8

1st

2nd

Tankguard HB

Tankguard HB

150

150

Amine AdduciEpoxyAmine AdductEpoxy

Sa21nWater, Refined &Crude Palm Oil Tanklnterior

10-12For more details on chemicalresistance please refer to Jotun.

JPCS 9

lsl

2nd

3rd

2nd

Re5isl t6

SolvalittAluminiumSolvalittAluminiumorResist 78

SolvalittMidtherm

2\

75

75

30

lnorganic ZrncSilicateSiliconeAluminiumSiliconeAluminium

lnorganic ZincSilicateSilicone Acrylics

Sa 2tn

Steel Operatinqbetween 120'C -400"C

Steel Operating upto 250"C

8-1 0

Solvalitt is also available in Redand White but temperatureresist is up to 350'C only.

Solvalitt Midtherm is alsoavailable in WhiteNote: The {unction of lnorganicZinc Primer is to improveCorrosion Protection

JPCS 1O

1st

2nd

l5t

2nd

SolvalittAluminiumSolvalittAluminiumofSolvalittMidthermSolvalittMidtherm

25

25

30

3&

SiliconeAluminrumSiliconeAluminium

Silicone Acrylics

Silicone Acrylics

Sa 2tn

Steel Surface Operatingabove 400"C - 600'C

Steel Operating upto 250"CSteel Operating upto 250'C

5-8

High temperature paint on itsown generally do not havegood corrosion protectionproperty and will normally havea shorter life span compared tothe system which uses anlnorganic Zinc Silicate Primer asthe 1st coat.

Note: Paint system pefiarmike depends an the degree of surtace preparation, better surface preparation wil! ensure be.tter pertormance.

6JOTUH

i;,

?TJ so'+6"co-sl

Surface preparation : Blast cleaning to ISO 8501-1 : 1988, Sa 2.5

6.2.1.3 Coating System No. 1C : Maintenance Painting for Power Tool Cleaned Surface

Surface preparation : Power tool cleaning to ISO 8501-1: 1988, St 3

I PA|NTING AND COATTNG SYSTEM SCHEDULES FOR EXTERNAL AppLtCATtON )Carbon Steel Design Temperature < 110 deg C NON INSULATED in the Atmospheric Zone

I Coating System No. 1A: lnitialPainting

Surface preparation : Blast Cleaning to ISO 8501-1 : 1988, Sa 2.5

Coatlng system DFT

1 stcoat lnorganic Znc Silicate / Epoxy Zinc Rich 75 tr

2 nd coat High Solid epory 150 tl3 rd coat Aliphatic polyurethane 50 v1< 11

Total 275 _MX ?_

-PS,,',/

.2 doatingsf ,s:tel-ntrl"rf:Mdifr tffi nceFbintingToTE-ldErcfeaE

Coating system DFT

1 st coat Epoxy zinc rich 75 u

2 nd coat High solid epoxy 150 p

3 rd coat Aliphatic polyurethane 50 u

Total 275 p

Coating system DFT

1 st coat Surface tolerant HIGH SOLID epoxy 125 p

2 nd coat Surface tolerant HIGH SOLID epoxy 125 p

3 rd coat Aliphatic polyurethane 50 uTotal 300 p

ld r*d

Techmical DataBARRIEF.-TT

Product descriptionBdrrier 77 is a two-pack zinc rich epaxy primer.

Reccmmended useAs a primer on blast cleanedt0 further improve protecti0n

steel. Barrier 77 is used in combination withagainst corrosi0n.

advanced coating systems

Film thickness and

Film thickness, dry (pm)Film thickness, wet (pm)Thcor€tical spreading rate{m"11}

spreading rateMinimum Maxirnum Typical

25 75 5045 140 952L,2 7 ,r 1"0,5

Physical prsBertiesColourSslids {vol t/o}*

Flash point

Glossrdlater resistanceAbrasion resistenee$olvent resistanceFlexibility*Measured according

.Grey53*2

25oC * 2 {Seraflash)

FlatExcellentVery goodVery qoodGood

to lSO 3233:199B (E)

Surface FreparationAll surfaces should be clean, dry and free from conlamination. The surface shouid be assessed andtreated in acccrdance with ISO 8504.

Bare steelcleanliness: Blast cleaning to min. sa 2lz (ISO 8501-1:1988) or for maintenance uHpw] to wl2{NACE No.S/SSPC-SP 12). Roughness: using abrasives suitable to achieve grade Fine to Mediilm G{30-85 pm, Ry5) (ISO 8503-2)

Shopprimed steelClean, dry and undamaEed approved shopprimer.

Other surfacesThe coating may be used on other substrates. Please contact your local Jotun office for moreinforrnation.

SAARIER 7/ Page 1 af3

Ccnditisn during applicaticnThe temperature of the substrate should be minimum SoC and at least 3oC above the dew point ofthe air, temperature and relative humidity measured in the vicinity of the substrate. Good ventilationis required in confined areas to ensure correct drying.

Application methadsSpray Use airless sprayBrush Recommended for stripe coating and small areas, care must be taken to achieve the

specified dry film thickness.

Application dataIt'tixing ratio {volume}

It'lixingPot life {23"C}

Thinner/CleanerGuiding data airless sprayPr€ssur€ at nozzleNozzle tiBSpray angleFilter

3 part Comp. A (base) to be mixed thoroughly with 1 part Comp. B(curing agent)

Vz hour prior to use.24 hours {Reduced at higher temp.).

lotun Thinner No. 17

15 lvlPa min {150 kplcm2,2100 psi.).0.38 - 0.53 mm (0.015 - 0.021").40 - 800Check to ensure that filters are clean.

Drying timeDrying times are generally related ts air circulation, temperature, film thickness and number of coats,and will be affected correspondingly. The figures given in the table are typical with:* Good ventilation (Outdoor exposure or free circulation of air)* Typical film thickness* One codt on top of inerL substrate

Substrate temFeratureSurface dryThrcugh dryCuredDry to recoat, minimum 1

Dry to recoat, maximum 1'2

50c50 min

10d3h

100c2O min2h,tu2h

230C10 min1,5 h

sd1,5 h

400c4 min0,7 h

2d0,7 h

The given data must be considered as guidelines only. The actual drying time/times before recoatingmay be shorter or longer, depending on fiim ttrickness. ventilation/ humidity, underlying paint system,requirement for early handling and mechanical strength etc, Acomplete system can be described ona system sheet, where all parameters and special conditions could be included.

Typical paint systemBarrier 77 I x 25 - 75 Um (Dry Film Thickness)

Subsequent coating(s) by choice e.g.: Epcxy, Acrylic erVinyl.

Other systems may be specified, depending on area ef use

BARRIER 77 Page 2 of 3

StorageThe product must be stored in acccrdance with national regulations. Storage conditions are to keepthe containers in a dry, cool, well ventilated space and awa! from source oiheat andignition.Containers must be kept tightly closed.

HandIingHandle with care. Stirwell before use.Continuous stirring during application will prevent the h*avyzinc pigment frcrn settling.

For detailed information on ths health and safety hazards and precautions for use of thisprq{_u_-c,t-tsqr_ef Er!q_the_!tq!€rie_t_$,a&tr_g_qllsbeet.

DISCLAIMERThe iftformatian in this data sheet is given ro lhe besr cf our knawledge based on labaratory testing andp{a€tical experiefice. However, as fhe product is often used under caiditians beyond aur io'ntrol, w"ecannat guarantee anyttling but the quality of the product itself. t4le rese!-ye the'right to change the givendata without natice.

Packing size9 litre r"rnit: 6.75 litres Comp, A(base) in a 10 litre container and 2.25 litres Comp. B (curing agent) ina 3 litre container.

Pecking may vary from counlry l0 cOuntry according to l0cal i-equi:-ements.

Health and $afetyPlease observe the precautionary notices displayed on the container. Use under well ventilatedcondilions. Do not breathe or inhale mist. Avaid skin cantact. Spiliage on the skin shoutd i'-nmediatelybe removed with suitable cleanser, soap and water. Eyes should be weli flushed with water andmedical attention sought immediately.

Head Office & NordicJotun Paints

P.O. Box 2021N -3248 SandefFrdN orway

Phorle +47 33 45 70 00Fax +47 33 46 46 13

EuropeJotun Paints {Europe) Ltd.

Stather Road, FlixboroughNodh Lincolnshire Dttl 158RR

United Kingdom

Phone +44 172 44 AA OOA

Fax +44 772 44 00 100

Ftfiddle Eastlotun U"A.E Ltd. LLC"

Al Quoz Industrial Area

P.{} Box 3671Dubai U.A.E

Phone +977Fax +97t

South East Asialotun (Singapore) pte. LtdN0 11-1 5, Sixth Lok Yang

Road

I u rong

Singapore 628 111

Phon€ +65 6265 47114 3 39 50 00 Fax +65 6?S5 74A443380665

Jotun is a world wide cornpany with factories, sales offices and stocks in rnore than s0 countries. For yourneerest local Jotun address please contact the nearest regional office or visit our website at w!.rw.jotun.com

ISSUED 28 AUGUST 2OO3 BY JOTUN PAINTSTHIS DATA SHEET SUPERSEDES THCISE PREVIOUSLY ISSUED

SARRIER ?7 Page 3 ol3

.J.}r'-d f no t

Technical DataPENGUARD HB

Product descriptionPenguard HB is a high build, two-pack epaxy coating based on epoxy resin with high nroiecularweight. This product is a part of a complete syste$l which is certified not to spread surface flames.

Recommended useAs an anti corrosive primer and intermediate coating for corrosisn protection of varisus substratesincluding steei. May be used in tanks far potable water. A suitable washing procedure depending onnatienal rules may be required.

Filrn thicknes$ and

Film thickness, dry {;rm}Film thickness, wet {pm}Theoretical spreading rate(m'/ll

spreading rateMinimum Maximum Typical

B0 150 100150 280 1S56,8 3,6 5,4

Physical propertEesColour$olids (vol o/o)*

Flash point

Glo*sGloss retentignWater resistanceAbrasian resistanceSolvent resistance€hemical resistanceFlexibility

Grey" Red, White54*2

250C + 2 {Setaflash)

flatFairVery goodVery goodExcelientExcellenlttlnnd

xMeaEUred according to lSO 3233:1998 {E)

Surface preparation

All surfaees should be clean, dry and free from contamination. The gurface should be assessed andtreated in accordance with I5O 8504.

Bare steelCleanliness: Blasl cleaning to Sa 2% (ISO8501-1:1988). Roughness: using abrasives suitable toachieve grade Fine to Medium G (30-85 prm, Ry5) (I5O 8503-2)

Shopprimed steelClean. dry and undamaged approved shopprimer.

Coated surfacesClean, dry and undamaged compatible primer. Contact yaur lacal lotun effice for more information.

PENGUARD ItB Page 1 of4

Gthsr surfacesFor aluminium and galvanized surface; degreesing, tight abrading cr sand slveeping.

The coating may be used on other substrales. Please €sntact your local lotun office for moreinformaticn.

Condition during applicationThe temperature of the substrate should be minimum 10oC and at ieasl 3oC above the ciew point ofthe air, temperature and relative hurmidity measured in the vicinity of the substrate. Good ventilationis usually required in confined areas to ensilre proper drying. The caating should not be exposed taoil, chemicals or mechanical stress until cured. If ne€essary. Penguard Slayer, Penguard Primer,Penguard l-lB, Penguard Special may be used down to 2oC, provided a special accelerator is added.

Applicatisn methodsSpray Use airless sprayBrush Recommended for stripe coating and small areas, care must be taken to achieve the

speeified dry film thickness.

Application dataItlixing ratio (volume) 4 oarts Comp. A (base) to be mixed thorauqhly with 1 part Comp. B

(curing ag€nt)

Hixing 1/z hour prior to use.pot lif€ {23oCi B hours. (Reduced at higher temp.)

ThinnerlCleaner Jotun Thinner No. 17Guiding data airless sprayPressure at nozzle 15 MPa (150 kp/cmz 2100 psi)Nszzle tip 0.46 - 0,69 mm (0.018-0.027"1Spray angle 40 - 80oFiltar Check to ensLlre that filters are clean.

Drylng timeDrying times are generally related to air.ircuiation, temperature, film thickness and number of coatsand will be affecled correspondingly. The figures given in the table are typical with:* Good ventilation (Outdoor exposure or free circulation of air)* Typicai film thickness* One ccat 0n top 0f inert substrate

Substrate temp€rature lOoC 23oC 4OoCSurfacedry 5h Z,5h thThrough dry 16 h I h 3,5 hCured 14d 7d 3dDry to re€oat, minimum 16 h g h 3,5 hDry t0 reccatr maximum r

The given data must be considered as guideiines only. The actual drying timeltimes before recoatingmay be shorter or longer, depending on film thickness" ventilation, humidity, underlying paint system.requirement for early handling and mechanical strength etc. A complete systen'} can be described ona system sheet, where all parameters and special csndilions could be included,

PiI'JGUA** H* Fage 2of4

- Typlcal paint system1) 0n bare steel 0r shopprimer:Penguard HB 2 x t OO pm (Dry Film ?hickness)Penguard Topcoat 1 x 50 pm (Dry Film Thickness)

Penguard Primer 1 x 50 pm {Dry Film Thickness)Penguard HB 1x 1OO pm {Sry Film Thickness}Penguard Topcoat 1 x 50 ;rm (Dry Film Thickness)

Other systems may be specified, depending on area of use

SPECIAL WASHIITG PROCEDURE WHEH THIS PRODUCT IS USED IHTAf{KS FOR POTIIBLE WATER

EitherAfter the paint is cured (see dryinglcuring time above), the tank is filled wlth warm water (above 60 -80aC), which shall remain in the tank for 24 hours. Then the tank is thoroughly washed, using waterof min. 80oC together with brushes or washed with steamorAfter the paint is cured (see drying/curing time above), the tank shall be ventilated with warm air,min 23oC for 7 days. Then the lank is filled three times with warm water (min. 50oC), each filling shallremain in the t€nk for 24 hours. Finally, the tank is washed, using water of min. 50oC together withbrushes sr washed with steam

Other washing procedures may be acceptable, please contact your local Jotun representative fordetails.

StorageThe product must be stored in accordance with nsi:*aral regulfitions. Storage conditions are to keepthe ccntainers in a dry, cool, well ventilated space and away from scurce of heat andignition.Containers must be kept tightly closed.

HandlingHandle with care. Stir well before use.

Packing size20 litre uniti 16 litres Comp. A (base) in a 20 litre container and 4litres Comp. B (curing agent) in a 5litre conlaineror5lilreunit:4litresComp.A(base)ina5litrecontainerandllitreComp.B{curingagent)inallitrecontainer

Packing may vary from country to country according to loca! requiremenls.

PEhJGI-JARD HB Page 3of4

Health and safetyPlease observe the precautionary notlces displayed on lhe container. Use under well ventiiatedcondilions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediatelybe rernoved with suitable cleanser, soap and water. Eyes sl'rould be weli flushed with water andmedical attention sought immedialely.

Far detailed informatisn on the health and safety hazards and precautions for use of this?f4!9-t,ry,e_rgfg,rtg_!h€ryqte,r-r_alF_qf,€!r,pg,tqJ!!qg!1

DISC*.EIMFRThe infarmatian in this data sheet is given ta the best af our l<nowledge based on laboratory testing andpractical experience. fl}wever, as the praduct is ofren used under cofiditians beyond our control, wecanftat guarantee anything but the quality of the praduct itself. We resewe the right to change the givesdata withaut noUce.

Head Office & NordicJctun Paints

P,C. Box 2021

N-3248 Sande{j*rd

I,lon/ay

Phone 447 33 45 70 00Fax +47 33 46 46 13

EuropeJotun Palnts (Furope) Ltd.

Stather Ro;jrd, Flixboroughll0rth Lincolnshire Dfi 15

8R.R

United Kingdom

Phone +44 17? 44 00 000FaY +44 17? 44 OO 1OO

I'liddle Easti0tiln U.A,H ltit. LLC.

Al Qiloz Indugtrial Area

P.C) Box 3671Dubal U "A.E

Phone +971 4 3 39 50 00Fax +971 4 3 38 06 66

South East Asia.10tun {SinqaD0rej Pte. Ltd.N{} 11-15, Sixth Lek Yang

Rt)ad

lurong

Singapore 6?8 :111

Phon€ +65 6?65 471 1

Fax +65 6265 7484

lotun is a Worid Wide company with factories, *ales offices end stocks in more than 50 countries. For yournearest local Jotun addregs please contact the nearest regional office qr uisit our website at www.jotun.cam

ISSUED 13 APRIL 2OO4 BY ]OTUN PAINTSTHIS DATA SHEET SUPERSFDES THOSE PREVIOUSLY ISSUED

P=l.,iGUA=3 -S Page 4 ol4

syd { a#

Technical DataHARtrTOP XF

Produet descriptionA twe-pack high sotid, aliphatic polyurethane topcoat with excellent Eloss and colour retention.

Recommended useAs a glossy topcOat over mostin a wide range of aggressive

epoxy $listems wherealmospheres.

a durable, weather-resistant finish is required

Film thickness and

Film thickness. dry {pm}Film thickness, wet (pm)Theoretical spreading rate

spreading rate]'{inimum Maximum Typical

40 80 6065 130 9s

(mzll) 15,8 7,9 10,5

Physical properties€olsurSolids (vol o/o)*

Flash point

voc

GlossGloss retentionWater resistance

.A,ccording to colour card and Multicolcr tinting systenr {MCI)63*2

30oC + 2 (Setaflash)

320 gms/ltr UK-?G6/23(97). Appendix 3

GlossyExcellenlVery good

Abrasion resistance Very goodSolvent resistance Very qoodChemical resistance Very gaadFlexibility Very qsod*Measured according to ISO 3233:1998 {E)

Surface preparation

All surfaces shouid be clean, dry and free from contamination. The surface should be assessed andtreated in accorciance with ISO 8504.

Coated surfacesCiean, dry and undamaged compatible primer. Please contact your local .lotun office for moreinformation.

Other surfacesThe coating may be used on other substrat€s. Please contact your local lotun sffice for mcreinformation"

HARf:;*3 XF Fage '! *f 4

Condition during applicatienThe temperature sf the substrate should be minimum OoC and at least 3oC abclve the dew point ofthe air, temperalure ancj reiative humidity measured in the vicinity of the substrate. Good ventilatlonis usually required in confined areas to ensure proper dryinE.

ApBlication methodsSpray Use airless spray or conventional sprayBrush Recommended for stripe coating and small areas, care must be taken to achieve the

specified dry film thickness.Roller May be used. However when using roller application care must be taken to apply

sufficient material in order to achieve the specified dry film lhickness.

Application datat{ixier$ ratie {valum*} 10 perts Comp. A {Base) to be mixed iharoughly wilh 1 pert Cori'}p. B

{Curing agent).

Pot life (23oC) 1,5 hours

Thinner/Cleaner Jotun Thinner No. 10Guiding data airless spray

Pressure at nozzle 15 MPa (150 kplcm2, 2100 psi)Nozzle tip 0.28-0.38 mm {0.011-0.017"}Spray angle 40-800Filter Check to ensure that filters are clean.

Drying timeDrying times are generaiiy related to air circulation, temperature, film thickness and numl,rer of coats,and will be affected correspondingly. The figures given in the table are typical with:* Gcod ventilation (Outdoor exposure or free circulation of air)* Typical film thickness* One coat on top of inert substrate

Substrate temperature SoC 1.OoC 23oC 4OoCSudacedry 16h 6h 3,5h 2hThroughdry 24h 14h 7h 4h- Cured 21d t4d 7d 3dDry ta recoat, minimum 24 n 14 h 7 h 4 hDry to recoat, maximum 1

1. The surface should be dry and free fram any contamination or chalking priorto applicaticn of thesubsequenl coat.

The given data n"lust be considered as guidelines only. The actuai drying timeltirnes before recoatingnray be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint syst€m,requirement f*r early handling anci mechanlcal strength efc. A complete syslem can be described ona system sheet, w*ere all paramelers and special cr:nditicns c*uld be :ncluded.

HARDTCP XF Page 2 of4

Typical paint systern

Jolac0te Universal I x 150 pmHardtop XP I rt 5O pm

lotamastic B7 1 x 15S pmHardtopXP Lx 6Opm

(Dry Film Thickness)(Dry Film Thickness)

(Dry Film Thickness){Dry Film Thicknessi

Other systems may be specified, depending on arGa of use

StorageThe proeluct must be stored in accordance with natlonal regulations. Storage conditions are to keepthe containers in a drry, cool, well ventilated space and away from source of heat and ignition.Conteiners must be kept lightly closed.

HandlingHandle with care" Stir well before use.

Packing size20 litre unit: 18,2 litres Comp, A (base) in a 20 litre container and 1,8 litres Comp. B {curing agent) ina 3 litre container or5 litre unit: 4,55 litres Comp. A (base) in a 5 lilre container and O.45 litre Comp. B {curing agent) in a1 litre c0nlaiiler

Packing rnay vary frorn country to country according to local requirements.

Health and safetyPlease observe the precautionary notices displayed on the contalner. Use under well ventilalecjconditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immedietelybe removed with suitable cleanser, soap and water" Eyes should be i,rell flushed with waLer andmedical attention sought immediately.

Fcr detailed infsrmation on the health and safety hazards and precautions for use af thisp.r-o*dl4$.q.eLsf qr!S_!,he_tsa!erra!-9,e!e-tr_9A!Eqheqt_,

DISCLAIMERThe infornation in thfs data sheef is given to the best af aur knowledge based an laboratory testing andpractical experience. However, as the product is aften used under conditians beyond ourco'ntro!, wicannot guarantee anVthing but the quality of the product itself. We reserve the right ta change the givendata without notice.

Head Office & Nordic Europe ' Middle East South fast AsiaJotun A/5 lotun paints {Europe) Ltd. Jotun U.A.E Ltd. LLC" lorun (singapore} pte. Ltd.P.O. Box 2021 Stather Road. Ftixborough No 11-15. Sixth Lok Yang

N-324S Sandefiord North Lincolnshire Dt{15 Al Quoz Industrial Area Road

Norway 8RR P'o Box 3571 Jurong

phone +4? 33 45 70 00 united Kingdom Dubai u-A.r sinoapore 628 111Fax +47 33 4S 46 13 Phone +44 172 44 00 000 phone +65 6265 4711

tax +44 !'12 44 *n 100 ?i**e +971 4 3 39 5S 00 Fax +65 S?65 Z4B4F.x +gjlt + 3 38 86 66

HAR|}?*F HP Page 3ol4