APPENDIX J - Lacey, Washington€¦ · CF-CO-LACEY-1 Rev. 5.0, 01/2018 CERTIFICATE OF ORIGIN City of Lacey Engineered Wastewater Collection System Single Family Residence using 1500

APPENDIX J

CF-CO-LACEY-1 Rev. 5.0, 01/2018

CERTIFICATE OF ORIGIN City of Lacey

Engineered Wastewater Collection System

Single Family Residence using 1500 or 1700 Gallon Tank

Two Family Residence (Duplex) using 3000 Gallon Concrete Tank

The following Collection System On-Lot Package is certified to have been manufactured by Orenco Systems®, Inc., Sutherlin, Oregon. The On-Lot Package equipment listed below is covered by an extended factory warranty under the terms and conditions of Orenco Systems’ Certificated Products Limited Warranty in effect at the time of sale.

On-Lot Package Code: PSA10-S1DS-LACEY-WA

Adhesive: ................................................................... (3) ADH100

Splice Box: ................................................................ (1) SBEX1-4, (3)SBHSY, (5)SBHSB

Biotube® Pump Vault: ................................................ (1) PVU57-1819-L

Float Assembly: ......................................................... (1) MFPG-27V-LACEY

Discharge Assembly: ................................................. (1) HV100BFCPR-80, (1) HVX100PR-80

Effluent Pump: ........................................................... (1) PF100511, (1) PPSC-10

Control Panel: ............................................................ (1) S1DS-LACEY

Homeowner Manual: ................................................. (1) PMHOMEMANUAL

Installation Manual: ................................................... (1) PMPSPPINST

Certificate of Origin: .................................................. (1) NCF-CO-LACEY- 1

Additional Orenco Equipment Required for a Complete Installation:

PVC Access Risers & Accessories: .......................... (1) RR30XX+SX, (1)RLA30, (1) G1L, (1) RR24XX, (1) RLA,24

Riser Adapters (Cast into Tank) ................................ (1) PRTA24, (1) PRTA30, (1) PRTA08

Fiberglass Access Lids: ............................................. (1) FLF30G, (1) FLD24G, (1) FL8G

Service Connection Valve Assembly ......................... (1) SC125-LACEY

For Customer Use: Site address:

Lot number:

Development:

Installer: Install Date:

Vendor:

City Inspector:

eandrewsText BoxJ-01

ADH100 AdhesiveGeneralADH100 is a single component opaque adhesive formulatedto bond PVC risers to Orenco grade rings and PRTA seriestank adapters. Upon curing, the seal created is both waterand chemical resistant.

Standard ModelADH100

Submittal Data Sheet

SpecificationsGel time is approximately 10 minutes; ultimate bond strength occurs after 24 - 72 hours at 70˚ - 85˚ F. Cure time is increasedgreatly with a decrease in temperature; not recommended for use in temperatures below 32˚ F.

Expected shelf life is approximately 5 years when stored at temperatures between 45˚ - 85˚ F.

NSU-RLA-ADH-3Rev. 2.2, © 1/01

ApplicationsADH100 is used to bond PVC risers to Orenco grade ringsand PRTA series tank adapters.


© 2009 Orenco Systems® Inc. NTD-SBEX-1Rev. 1.0, © 5/09

Page 1 of 2

External Splice BoxTechnical Data Sheet

Applications The Orenco® External Splice Box attaches outside the access riser of an underground tank. It is engineered specifically for water and wastewater treatment systems and is especially suited for use in locations prone to high groundwater and other wet conditions. Its separate conduit hubs, large volume, and optional dividers make it useful for maintaining isolation of high and low voltage wires where needed. It has four cord grips which accom-modate power cords for floats and pumps of 0.170 - 0.470 inches (4.3 - 11.9 mm) in diameter. Unused cord grips can be plugged watertight with the supplied cord grip plugs. Each External Splice Box is provided with a hole-cutting template to simplify installa-tion on the riser.

General To specify the Orenco External Splice Box for your installation, require the following:

need to open the riser lid

3 3) for easy wiring access and to accommodate multiple wiring configurations

below minimum burial depth

exposure, suitable for external applications

tage wires from separate conduits or direct-bury cable

SBEX1-4 -

External splice box

Blank = no divider platesP = divider plates

Standard Models

Nomenclature

The External Splice Box is molded of a UL (f1) rated PVC alloy. It has a UL Type 6P list-ing for prolonged submergence.


© 2009 Orenco Systems® Inc.NTD-SBEX-1Rev. 1.0, © 5/09Page 2 of 2

External Splice Box (continued)

Materials of Construction

O-rings Buna rubber

Physical Specifications 3 3)

accommodated

accommodated 1 in. (with coupling) ½ in. (with fitting or bell end)

into riser (hole-cutting template included)

(114 mm)

Optional divider

plate

Optional divider

Threaded cap

(4)

plugs (3)

hub plug (1)


Applications Orenco Biotube® Pump Vaults are used to filter effluent that is pumped from septic tanks or separate dosing tanks in STEP systems and onsite wastewater treatment systems. They remove two-thirds of suspended solids, on average. Pump vaults house a Biotube effluent filter and one or two Orenco high-head effluent pumps and can be used in single-compartment septic tanks with flows up to 40 gpm. When flows are greater than 40 gpm, a double-compartment septic tank or separate dosing tank is recommended.

General The Orenco Biotube Pump Vault includes a molded polyethylene housing with an internal filter cartridge constructed of polypropylene and PVC. Schedule 80 PVC support pipes are included to suspend the vault in a tank opening. The filter car-tridge can be removed without pulling the pump or the vault. Effluent enters through inlet holes around the perimeter of the Biotube vault and flows through the Biotubes to the external flow inducer. The external flow inducer accommodates one or two pumps. Orenco Biotube Pump Vaults are covered by U.S. patents #4,439,323 and 5,492,635.

Standard ModelsPVU57-1819-L.

Nomenclature

© 2009 Orenco Systems® Inc. NTD-PVU-LACEYRev. 1.0, © 6/09

Page 1 of 2

Universal Biotube® Pump VaultsTechnical Data Sheet

For use with Orenco 4-in. Submersible Effluent Pumps

Materials of ConstructionSupport pipe: Schedule 80 PVCBiotube® vault: PolyethyleneBiotube cartridge: Polypropylene/PVCFloat stem: Schedule 40 PVCDrain valve ball: Polypropylene

External flow inducer

Inlet holes

Side view

Support pipe

Support pipe length:L = Long support pipes for 30" riser

Inlet hole height (inches)

Cartridge height (inches)

57 - 18 19PVU

Vault height

Universal Pump Vault

- L


DRAW

N BY

: CD

Ore

nco

Syst

ems

Inco

rpor

ated

RDa

te:

6/1/

06

CUST

OM D

RAW

ING:

REVI

SION

:1

Instructions

Installation Instruction

X-STYLE VAULT INSTRUCTIONSPART# INSTR-X

1" SCH. 40 PVCCUT LENGTH 48 3/4"

18

DO NOT GLUE JOINT

USE REINFORCED TOP

PVUP

57-1

819-

L

WOR

K OR

DER

#

APPR

OVED

BY:

MAS

TER:

1391

37

3055

73

Universal Biotube® Pump Vaults (continued)Technical Data Sheet

© 2009 Orenco Systems® Inc. NTD-PVU-LACEYRev. 1.0, © 6/09

Page 2 of 2

SpecificationsModel PVU57-1819-LVault height (F) 57 in. Lowest float setting point (G) 29 in. Inlet hole height (H)* 19 in. Biotube® cartridge height (J) 18 in. Biotube mesh opening 0.125 in.Filter flow area 4.4 ft2 Filter surface area 14.5 ft2 Maximum flow rate 140 gpm

* May vary depending on the configuration of the tank.

Side view cutaway

C

D

Top view

Support pipes

H

F

2" min.

J

G

A

B

DimensionsA 3.0 in.B 4.0 in.C 17.3 in.D 16.6 in.E 12.0 in.

Drain valve ball

E


Technical Data Sheet

Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-MF-MF-1Rev. 3.0, © 03/17

Page 1 of 2

Float Switch Assemblies

Materials of ConstructionFloat housing Impact-resistant, noncorrosive PVC plastic for use in liquids up to 140˚ F (60˚ C)

Float cord, Flexible 2-conductor (UL, CSA) SJOOW; Super Vu-Tron® P and N models Supreme, yellow

Float cord, Flexible 2-conductor (UL, CSA) SJOW; water-resistant All other models (CPE); neoprene coating

Float collar ABS

ApplicationsFloat switches are used to signal liquid level positions for alarm and pump control applications. Orenco float switch assemblies can be mounted in pump vaults, effluent screens, pump basins, and risers.

GeneralAll models listed are UL listed and CSA certified for use in water or sew-age. Non-mercury float switches (models B, C, N, and P) are used where components containing mercury are prohibited.

Float switches are typically ordered in assemblies that include one or more switches mounted on a 1-inch PVC float stem. ABS float collars are used to provide secure mounting that is easily adjustable.

Normally-open “P” float switches have a blue cap for easy identifica-tion; normally-closed “N” float switches have a red cap. “P” and “N” model float switches use Super Vu-Tron® electrical cords for superior chemical and water resistance.

Standard ModelsB, C, G, N, P

Product Code Diagram

When ordering float switch assemblies, remember to list float switches from the top of the float stem down. An “MFPBN-” nomenclature indi-cates one “P” switch at the top of the stem, one “B” in the middle of the stem, and one “N” switch at the bottom of the stem; an “MF2PN-” indicates “P” switches at the top and middle of the stem, and one “N” switch at the bottom of the stem.

The “On” and “Off” positions describe normally open floats. For normally closed floats, the functions are reversed.

On

Off

Float collar

Float tether

Set point

Draw

dow

n

X

Y

Float stem

MF

Cord length option:Blank = 10 ft (3 m), standard20 = 20 ft (6 m)30 = 30 ft (9 m)50 = 50 ft (15 m)

Number of float switches (when using multiples of the same float switch model):Blank = no multiples of the same float switch model

Float stem length:Blank = no float stem (floats and collars only)19, 21, 27, 33, 37, 39, 45, 51, 57, 66 = stem length, in.5, 11 = stem length, in. (for elbow-style float brackets)

Application:FS = field setFTL = elbow-style (base-inlet filters only)PB = pump basinV = pump vault (standard float settings)STEP = Standard float settings for STEP STEPRO = Standard float settings for STEP with redundant off SVCOM = Standard float settings for VCOM simplex

- -

Float switch assembly

Float switch models (listed in order from the top of the float stem down):B, C, G, N, P

MFPG-27V-LACEY

P

G


© 2009 Orenco Systems® Inc.NTD-MF-MF-LACEYRev. 1.2, © 7/09Page 2 of 2

Float Switch Assemblies (continued)

Float State1 Type2 IR3 Volts Amps hp Tether X Y Drawdown4

Signal-rated mercury floats5 (for control switch applications)

A Modela Normally open Mercury Yes n/a n/a n/a 2.00 in. n/a n/a n/a

Motor-rated floats (for pump switch applications)

G Model Normally open Mercury No 120 V 15A ¾ hp 2.00 in. 1.50 in. 3.00 in. 4.50 in.

240 V 15A 2 hp 3.00 in. 1.75 in. 3.00 in. 4.75 in.

4.00 in. 2.00 in. 3.50 in. 5.50 in.

a. Suitable for use with VCOM and MVP.

Signal- and Motor-Rated Float Switch Matrix

Notes1 State: normally open or normally closedThe default state of a float — normally open or normally closed — refers to the contact positions in the float when the float is resting (down). Float switches have an internal contact. The terms “normally open” (N/O) and “normally closed” (N/C) refer to the state of the float switch contact in the down position. A normally open float switch has an open contact (off) in the down position and a normally closed float switch has a closed contact (on) in the down position. Different panel functions require different types of float switches. Most applications require float switches that are normally open. One notable exception is the redundant off and low-level alarm function that requires a nor-mally closed float switch, except with MVP and VCOM panels.2 TypeFloats have mechanical or mercury contactor types. The important distinction between these is that mercury floats are not rated for potable water.

3 IR (intrinsically safe relay)Approved for use with intrinsically safe, Class I, Division 1 applica-tions, where reliable float switch operation with very low current is required. 4 DrawdownDrawdown (in inches) refers to the difference in liquid level between a float switch’s activation and deactivation points. Drawdown can be altered by adjusting the tether length of the float switch cord. When selecting float switches, keep in mind that any float switch that can directly start and stop a pump (one that has no motor contactor in the control panel) should have a drawdown capability, to avoid rapid cycling of the pump.


© 2009 Orenco Systems® Inc. NTD-HV-HV-LACEYRev. 1.1, © 6/09

Page 1 of 1

Discharge AssembliesTechnical Data Sheet

ApplicationsOrenco Discharge Assemblies are used to convey effluent from a pump to the exterior of a riser or pump basin. They come in high-head configuration, for use with submersible turbine pumps. An external flex extension is recommended for installations where tank settling may occur to avoid line breakage during settling. Discharge assemblies for use in 1500-gallon STEP tanks include a ¼" flow control orifice.

GeneralOrenco Discharge Assemblies are corrosion-resistant and adjustable for a proper fit. Discharge assemblies are com-posed of PVC valves and flexible hose that simplify installation and maintenance. The flexible hose damps vibrations from the pump and allows for easy installation. All parts are either sol-vent welded or threaded and sealed with Teflon® paste. Teflon® is a registered trademark of DuPont.

Standard ModelsHV100BPR80, HV100BFCPR-80, HVX100PR-80, PPSC-10

Nomenclatures

Stainless steel check valve

Discharge diameter:10 = 1 in.

Pump part

PP - 10SC

Options:PR = High pressure

Discharge diameter:100 = 1 in.

Flex extension

Pump discharge assembly

Schedule 80

HV - 80X PR100

Materials of ConstructionComponent MaterialBall valve Schedule 40 PVCFlowmatic check valve Stainless steelPipe and fittings Schedule 80 PVCFlexible hose PVCExternal flex hose PVCFlow control disc Schedule 80 PVCGate valve Schedule 80 PVCUnions Schedule 80 PVCHigh-pressure flex hose Special elastomer compound

Component Working Pressure RatingsValves 150 psi (10 bar) at 73˚ F (23˚ C)Unions 150 psi (10 bar) at 73˚ F (23˚ C)

High-Pressure Hose SpecificationsThickness and working pressures at 73˚ F (23˚C) Size Wall Working (Nominal) thickness pressure 1.00 in. 0.235 in. 250 psi

kbi

High-Pressure HoseHose and Valve Assembly

Stainless Steel Check Valve

Options:B = Ball valveFC = ¼" flow controller (1500-gallon STEP tanks only)PR = High pressure

Discharge diameter:100 = 1"


Schedule 80

HV - 80100 ¼" flow control (for 1500-gallon STEP tanks only)

HV100BFCPR-80 HVX100PR PPSC-10

BFCPR


Features/SpecificationsOrenco 4" Submersible Effluent Pump has the following features:

Minimum 24-hour run-dry capability with no deterioration in pump life or performance1/8" bypass orifice (patent pending) to ensure flow recircula-tion for motor cooling and to prevent air bind

ownership

Standard Model

Nomenclature

ApplicationsOrenco® 4" Submersible Effluent Pumps are designed to trans-

plastics; all are field-serviceable and repairable with common -

® are used in a variety

-

to be used with a Biotube®

connection

Bypass orifice

Suction connection

su

per s

tain

less

mot

or

LR80980LR2053896

PF Series 4" Submersible Effluent Pump


© 2011 Orenco Systems® Inc. NTD-PU-PF-LACEYRev. 1.4, © 12/11

Page 1 of 2

Voltage (nameplate):1 = 115 VAC2 = 230 VAC

Frequency:1 = Single-phase 60 Hz

Horsepower:05 = ½ hp

Nominal flow (gpm):10 = 10 gpm (for 1500-3000 gallon STEP tanks)20 = 20 gpm (for 8000-gallon STEP tanks)

PF series 4" submersible effluent pump

PF 05 1

10

1


Specifications

60 Hz

Model

1 ⁄8 ®2 Biotube®

PF Series High-Head Effluent Pumps

Desi

gn g

pm

(in.)

Hors

epow

er

Phas

e

Nam

epla

te

volta

ge

Actu

al

volta

ge

Desi

gn fl

ow

amps

Max

am

ps

Impe

llers

Disc

harg

e si

ze1

Leng

th (i

n.)

Min

. liq

uid

le

vel,2

(in.)

Wei

ght,3

(lb)

Rate

d cy

cles

/day

Materials of Construction

®

Suction connection: Stainless steel

© 2011 Orenco Systems® Inc.NTD-PU-PF-LACEYRev. 1.4, © 12/11Page 2 of 2

Using a Pump Curvepump curve helps you determine the best pump for your

a graphical representation of a pump’s optimal performance nominal flow rate — the

-

Orenco’s PumpSelect

Tota

l dyn

amic

hea

d (T

DH) i

n fe

et

Flow in gallons per minute (gpm)142 4 6 8 10 16 18 20 22 24 26 28 30120

20

0

40

60

80

100

120

140

160

180

200

220

240

260

280

300

PF Series 60-Hz 0.5 hp PF100511

PF200512

PF1005with 1/4"

flow control


© 2009 Orenco Systems® Inc. NTD-CP-S-LACEYRev. 1.0, © 6/09

Page 1 of 1

Simplex Control Panels – Lacey, WATechnical Data Sheet

ApplicationsOrenco Simplex Control Panels are used to control effluent pumps, alarms, and other equipment as specified in pressure sewers and onsite septic systems.

GeneralOrenco Simplex Control Panels are specifically engineered for pressure sewer (STEP) systems, onsite septic treatment systems, and pump control into conventional gravity systems. Standard features include circuit breakers, an automatic/manual/off toggle switch, automatic motor control operation, and an audible/visible high water level alarm with auto reset.

Standard ModelsS1DS-LACEY

Nomenclature

Materials of ConstructionEnclosure UV-resistant fiberglass, UL Type 4XHinges Stainless steel

DimensionsHeight (in.) 11.5Width (in.) 9.5Depth (in.) 5.4

SpecificationsPanel ratings 120 V, 3/4 hp, 14 A, single phase, 60 Hz 1. Motor-start 16 FLA, 1 hp, 60 Hz; 2.5 million cycles at contactor FLA (10 million at 50% of FLA) 2. Circuit 120 V, 10 A, OFF/ON switch, Single pole breakers 3. Toggle switch Single-pole, double-throw HOA switch, 20 A 4. Audio alarm 95 dB at 24 in., warble-tone sound, UL Type 4X 5. Audio alarm 120 V, automatic reset, DIN rail mount silence relay6. Visual alarm 7/8-in. diameter red lens, “Push-to-silence,” 120 V LED, UL Type 4X7. Disconnect switch Single-pole, single 1-1 throw, 20 A (not shown)

AUTO

OFF

MAN

Option:DS = Disconnect switch

Simplex panel, 120 VAC

S1 DS - LACEY


Simplex Operation

HHHiiiggghhh LLLeeevvveeelll AAAlllaaarrrmmm::: This float activates the alarm light and audible alarm when lifted. The audible alarm may be silenced by pressing the PUSH TO SILENCE button. The alarm light will remain on until the float is lowered.

PPPuuummmppp OOOnnn///OOOffffff::: This float turns on the pump when lifted. The pump will continue to run until the float is lowered.

AALASCBDSMPBSR

Key= Factory Wire= Field Wire= Audio Alarm= Alarm Light= Audio Silence Switch= Controls Circuit Breaker= Disconnect Switch= Motor Contactor= Pump Circuit Breaker= Silence Control Relay

Motor PowerVoltageMax AmpsHorsepowerHertzPhaseShort Circuit Current Rating:5,000A rms symetrical, 240V max

ControlsVoltageMax AmpsHertzPhase

Panel ModelS1 DS Lacey

Enclosure RatingUL Type 4X

Orenco Systems, Inc.

43

High LevelAlarm

(Y-Yellow)

Pump On/Off(G-Green)

Incoming Power Wiring Pump & Float Wiring

PowerL1

NeutralN

431 2 3 4 5 6 7 8

Panel Wiring DiagramModel S1 DS Lacey

Ground

3

Neutral N

M

T2L2

T1L1

42

Note: Motor must have

internal overload protection

Pump115 VAC / 1 Hp.1 Phase / 60 Hz.

From Main Power Panel115 VAC, 1 Phase, 60 Hz.

GroundLug

EDW-WD-S-131Rev 7.1 © 6/4/09

Power L1

CB 10A

PB 20A

M

A2A1OFF

HAND

AUTO

FS2 Pump On

A2A1SR

SR1411

65 FS3 High Level

-+A

SR1211

AS

87

X2X1

RAL


Blu

e

Bro

wn

Ye

llow

Ora

nge

Red

White

DS

1

120VAC161601

120VAC5601

PUMPGreen

Simplex Operation

HHHiiiggghhh LLLeeevvveeelll AAAlllaaarrrmmm::: This float activates the alarm light and audible alarm when lifted. The audible alarm may be silenced by pressing the PUSH TO SILENCE button. The alarm light will remain on until the float is lowered.

PPPuuummmppp OOOnnn///OOOffffff::: This float turns on the pump when lifted. The pump will continue to run until the float is lowered.

AALASCBDSMPBSR

Key= Factory Wire= Field Wire= Audio Alarm= Alarm Light= Audio Silence Switch= Controls Circuit Breaker= Disconnect Switch= Motor Contactor= Pump Circuit Breaker= Silence Control Relay

Motor PowerVoltageMax AmpsHorsepowerHertzPhaseShort Circuit Current Rating:5,000A rms symetrical, 240V max

ControlsVoltageMax AmpsHertzPhase

Panel ModelS1 DS Lacey

Enclosure RatingUL Type 4X

Orenco Systems, Inc.

43

High LevelAlarm

(Y-Yellow)

Pump On/Off(G-Green)

Incoming Power Wiring Pump & Float Wiring

PowerL1

NeutralN

431 2 3 4 5 6 7 8

Panel Wiring DiagramModel S1 DS Lacey

Ground

3

Neutral N

M

T2L2

T1L1

42

Note: Motor must have

internal overload protection


From Main Power Panel115 VAC, 1 Phase, 60 Hz.

GroundLug

EDW-WD-S-131Rev 7.1 © 6/4/09

Power L1

CB 10A

PB 20A

M

A2A1OFF

HAND

AUTO

FS2 Pump On

A2A1SR

SR1411

65 FS3 High Level

-+A

SR1211

AS

87

X2X1

RAL


Blu

e

Bro

wn

Ye

llow

Ora

nge

Red

White

DS

1

120VAC161601

120VAC5601

PUMPGreen


GPump On

YHigh Level Alarm Pump Cord

Splice Box Wiring Diagram

Cord GripHand tighten each cord grip

so that the cord will not easilyslide through the grommet.

YG

Yellow

Green

KeyBlack Wire

Green WireWhite Wire

Heat Shrink &Butt Connector *

Attention: Failure to follow splicinginstructions will void warranty

Note: Multi-function floats willhave more than one marker

--

Float Tag Colors

EDW-SB-S-8Rev 2.2 ©12/06/11

Drawing No.

EDW-SB-S-8Float Function Color Code

YGSplice Box Model

SBEX1-4Control Panel Series

Lacey Simplex

* Refer to drawing EIN-SB-SB-1 for splicing instructions.

To Terminal#6

Orange

To Terminal#5

Yellow

To Terminal#3

RedTo Terminal

#4White

To Terminal#8

Brown

To Terminal#7

Blue

To GroundLug

Green


© 2009 Orenco Systems® Inc. NTD-RLA-RR-LACEYRev. 1.0, © 6/09

Page1 of 1

Access Risers Technical Data Sheet

GeneralOrenco Access Risers are constructed of ribbed PVC pipe and are available in 24-in. and 30-in. diameters. The 24-in. ribbed ris-ers are available in three-inch increments up to 14 ft in length. The 30-in. risers are available in one-inch increments up to 13 ft in length.

Standard ModelsRR24XX, RR30XX

Nomenclature

ApplicationsOrenco’s Access Risers provide access to septic tank openings and can be cast into the tops of concrete tanks, bonded in place, or bolted down using a riser tank adaptor. They can also be used as valve enclosures.

Materials of ConstructionRibbed Risers: PVCBolt catch (30" risers only) PVC

SpecificationsModel RR24XX RR30XXI.D. (in.) 23.50 29.50Wall Thickness - excluding ribs (in.) 0.20 0.20O.D. - including ribs (in.) 25.63 31.00Weight per foot (lb) 19 18

Riser diameter:24 = 24 in. 30 = 30 in.

Riser height, inches

Ribbed riser

RR


© 2008 Orenco Systems® Inc. NTD-RLA-RLA-LACEYRev. 1.0, © 6/09

Page 1 of 1

RLA Riser-to-Lid AdaptersTechnical Data Sheet

ApplicationsOrenco® riser-to-lid adapters (RLAs) provide a secure, water-tight method of attaching an Orenco fiberglass lid to a 24-in. or 30-in. ribbed PVC access riser.

RLAs are especially useful when the top of the riser is uneven or has a damaged edge.

GeneralRLA adapters can be attached to 24-in. or 30-in. risers to sim-plify bolting a lid to the riser.

Standard ModelsRLA24, RLA30

Nomenclature

Materials of ConstructionAdapter ABSO-ring EPDM SpecificationsDimensions in inches (mm) RLA24 RLA30

A – Adapter height 1� (32) 1� (32)

B – Socket or lip width 1 (25) 1 (25)

C – Inside diameter 227⁄8 (581) 28⇥ (724)

D – Outside diameter 25⇥ (648) 31 (787)

E – Socket depth 3⁄8 (10) N/A

Riser style Perma-Loc™ Perma-Loc Ultra-Rib™

Lid bolt

RLA24 adapter

24-in. riser

Fiberglass lid

RLA24 riser-to-lid adapter

DC

A

BE


30-in. riser

Lid bolt

RLA30 adapter

Fiberglass lid

DC

A

B

RLA

Riser-to-lid adapter

Adapter diameter (inches):24 = 24"30 = 30"


© 2009 Orenco Systems® Inc. NTD-RLA-PRTA-LACEYRev. 1.1, © 6/09

Page 1 of 1

PRTA Tank AdaptersTechnical Data Sheet

ApplicationsPRTA tank adapters are used to provide a structural, water-tight method of installing an 8", 24", or 30" access riser over a tank opening.

GeneralOrenco’s PRTA tank adapters are molded plastic products and therefore have excellent part-quality and consistency. PRTA tank adapters are designed to be cast into a tank top, provid-ing a way to affix inspection or access risers.

Orenco's 8" adapters provide a slip-fit for 8" IPS PVC inspec-tion risers. Risers are placed in the inner sleeve and fixed into place with PVC cement. On 24" and 30" adapters, the O.D. of the vertical flange matches the I.D. of Orenco’s ribbed risers, which provides a suitable joint to seal with ADH100 adhesive.

Standard ModelsPRTA08, PRTA24, PRTA30

Nomenclature

SpecificationsDimensions (in.) PRTA08 PRTA24 PRTA30A 9 ½ — —B 8 5⁄8 — —C 5⁄32 — —D (lip width) 1/8 — —E ½ — —F 4 5⁄8 — —G — 23 ½ 29 ½H — 27 35I — ¾ ¾J — 1 ¾ 2 ½K — 3 ¼ 3

Materials of ConstructionTank adapter (8") Sand-coated PVCTank adapter (24" and 30") ABS

ABS tank riser adapter

PRTA

Riser diameter:08 = 8" (8" IPS)24 = 24" (Perma-Loc, Ultra-Rib, KOR FLO)30 = 30" (Perma-Loc, Ultra-Rib)

G

H

K

J

I

24" and 30" tank adapters

8" tank adapter

AB

C

DF

ECasting groove

Seating lip


Pipe GrommetsGeneralOrenco Pipe Grommets are constructed of corrosion-resistant rub-ber to provide long-lasting seals. Grommets conform to standardIPS sizes. Not all models conform exactly to the depiction shown.

Standard ModelsG05L, G075L, G1L, G125L, G150L, G2L, G3L, G4L, G6L

Nomenclature


ODID

GW

GD

T

SpecificationsDimensionsModel G05L G075L G1L G125L G150L G2L G3L G4L G6LOD (inches) 1 1/4 1 1/2 1 7/8 2 1/8 2 1/2 3 7/8 5 6 8 1/8ID (inches) 3/4 1 1 1/4 1 1/2 1 3/4 2 1/8 3 1/4 4 3/16 6 11/16GD (inches) 1 1 1/4 1 5/8 1 3/4 2 1/8 2 11/16 3 13/16 4 15/16 7 5/8GW (inches) 3/16 3/16 1/4 1/4 1/4 5/16 5/16 1/4 1/4T (inches) 1/2 7/16 9/16 5/8 5/8 15/16 15/16 7/8 13/16Holesaw Size (inches) 1 1 1/4 1 9/16 1 3/4 2 1/8 2 3/4 3 7/8 5 7

Material of Construction:

EPDM synthetic rubber in accordance with MIL-STD-417, 60 durometer.

NSU-RLA-PG-1Rev. 3.4, © 7/03

ApplicationsOrenco Pipe Grommets are used to provide a seal to prevent thepassage of liquids through pipe ports.

G

Indicates grommet diameter:05 = 1/2"075 = 3/4"1 = 1"125 = 1-1/4"150 = 1-1/2"2 = 2"3 = 3"4 = 4"6 = 6"

Grommet

LIndicates not installed


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-RLA-FL-2Rev. 2.0, © 03/17

Page 1 of 1

Fiberglass CapsTechnical Data Sheet

GeneralOrenco Fiberglass Caps are molded using fiberglass reinforced polyes-ter resin. Both non-skid (standard) and smooth surfaces are available. Standard color for the non-skid surface is green. Standard color for the smooth surface is white. Fiberglass caps are available with or without bolt holes and gaskets.

Standard ModelsFL8G, FL8GT, FL8GS

FL12G, FL12GT, FL12GS, FL12GTU

FL15G, FL15GT, FL15GS


Materials of ConstructionLid Fiberglass

Gasket Polyurethane

ApplicationsOrenco’s Fiberglass Caps are used as access covers for valve boxes and tank hatches. These lids are rated for pedestrian traffic only.

• FL8 caps fit 8-inch dia. IPS pipe, 8.63-inch (219 mm) O.D.

• FL12 caps fit 12-inch dia. PIP pipe, 12.24-inch (311 mm) O.D.

• FL12GTU caps fit 12-inch dia. Ultra-Rib™ pipe, 13.1-inch (333 mm) O.D.

• FL15 caps fit 15-inch dia. PIP pipe, 15.3-inch (389 mm) O.D.

SpecificationsDimensions FL8XX FL12XX FL12GTU FL15XX

O.D. in. (mm) 8 7/8 (225) 12 1/2 (318) 13 3/4 (349) 15 5/8 (397)

I.D. in. (mm) 8 5/8 (219) 12 1/4 (311) 13 3/8 (339) 15 3/8 (391)

Top thickness in. (mm) 3/16 (4.8) 3/16 (4.8) 3/16 (4.8) 3/16 (4.8)

Lip thickness in. (mm) 1/8 (3.2) 1/8 (3.2) 1/8 (3.2) 3/16 (4.8)

Bolt holes for top attachment shown

FL

Attachment method options:Blank = slip fitS = side screwT = top boltTU = top bolt, for 12-in. (300-mm) Ultra-Rib™ risers

Color and non-skid options:Blank = green color, non-slip surfaceW = white color, smooth surface

Gasket options:Blank = no gasket, standardG = gasket

Lid diameter, in. (mm):8 = 8 (200)12 = 12 (300)15 = 15 (375)

Fiberglass lid

FL8G



Page 1 of 1

DuraFiber™ Access LidsTechnical Data Sheet

ApplicationsOrenco® DuraFiber™ Access Lids provide a secure, damage-resistant cov-ering for ribbed PVC and HDPE risers, pump basins, and access ports. They are not recommended for vehicular traffic. 30-inch (750-mm) DuraFiber lids are not compatible with 30-inch (750-mm) RLA Riser-Lid-Adapters or 30-inch (750-mm) Perma-Loc™ pipe. For these products, use Orenco’s FLF-Series lids.

GeneralDuraFiber Access Lids are constructed of resin-infused fiberglass fabrics for extreme durability and damage resistance, with breaking strengths in excess of 20,000 pounds (9,000 kg).

They feature flat-style flanges for easier access, allowing clean, flush-to-grade installations. They have cored centering rings for aligning lids with risers. And they also have urethane gaskets to help provide watertight seals.

DuraFiber Lids feature a non-skid surface for better grip and aesthetics, a molded-in caution statement, and room for a customer logo. They come with four 5⁄16-inch stainless steel flathead socket cap screws and a hex key wrench.

Durafiber Lids are available with optional insulation, installed at the factory or in kits that can be installed in the field.

Standard ModelsFLD24G, FLD24GATX, FLD24GW, FLD30G, FLD30GATX, FLD30GW

Product Code Diagram FLD

Insulation:*Blank = no insulationI2 = 2-inch (50-mm) insulation installedI4 = 4-inch (100-mm) insulation installed

Vent and filter options:Blank = no vent or filter optionsV = ventCF = carbon filter

Gasket options:G = gasket (standard) Blank = no gasket

Lid diameter, in. (mm):24 = 24 (600)30 = 30 (750)

DuraFiber™ fiberglass lid

* Insulation has an R-value of 10 per 2-inch (50-mm) increment.

Color and logo options:Blank = green color lidB = brown color lidC = custom logoATX = AdvanTex® logoW = warning label

Materials of Construction:Lid Fiberglass reinforced polyester

Gasket Urethane

Centering ring core Structural foam

Mounting hardware Stainless steel

Insulation (optional) Closed-cell foam

Insulation mounting hardware Stainless steel

Specifications Model FLD24XX FLD30XX

A in. (mm) 26 (660) 33 (838)

B, in. (mm) 1½ (38) 1½ (38)

C, in. (mm) 23¼ (590) 29¼ (743)

Gasket width, in. (mm) ¾ (19) ¾ (19)

Bolt hole diameter, in. (mm) 5⁄16 (8) 5⁄16 (8)

Weight, lbs (kg) 11 (5) 20 (9)

Bolt holes, per lid 4 4

B

A

C

FLD24G



Page 1 of 1

FLF-Series Fiberglass Access LidsTechnical Data Sheet

ApplicationsOrenco® FLF-Series Fiberglass Access Lids provide a secure cover-ing for risers, pump basins, and access ports. They are capable of supporting a 2500-lb (1134-kg) wheel load; however, they are not designed or recommended for vehicular traffic. FLF-series lids will fit directly onto the riser types listed in the Specifications section.

FLF30 lids are required for retrofits on 30-in. (750-mm) Perma-Loc™ access risers or 30-inch (750-mm) Orenco RLA riser-to-lid adapters.

GeneralOrenco FLF-Series Fiberglass Access Lids are molded using fiberglass reinforced polyester resin with a structural foam core for added dura-bility and longevity. The finish is green or brown and the top surface is textured to provide a nonskid surface. Gasketed lids include a polyurethane gasket. FLF Lids come with four 5⁄16-inch stainless steel flathead socket cap screws and a hex key wrench.

Standard ModelsFLF18G, FLF21G, FLF30G



Core Structural foam

Gasket Polyurethane

SpecificationsModel FLF18G FLF21G FLF30G

Lid O.D. in. (mm) 20.25 (514) 22.5 (572) 32.6 (829)

Groove I.D. in. (mm) 17.50 (445) 20.25 (514) 28.75 (730)

Avg. thickness in. (mm) 0.75 (19) 0.75 (19) 1.0 (25)

Weight lb (kg) 4.15 (1.8) 6.25 (2.8) 11.50 (5.2)

Applications Ultra-Rib™ Ultra-Rib Perma-Loc™ Perma-Loc Kor Flo™

BottomTop

Cutaway view

Core Groove I.D. Gasket Lid O.D.

FLF

Color and logo options:Blank = green color lidB = brown color lidC = custom logoATX = AdvanTex® logo

Lid options:G = gasketV = ventCF = carbon filter installed in lidI2 = 2-in. (50-mm) insulation*I4 = 4-in. (100-mm) insulation

-


Fiberglass lid, FLF-series

* Lid insulation has an R-value of 10 per 2-inch (50-mm) incrementNote: For fiberglass basin bottoms without holes, order FLF18 or FLF21

FLF30G


© 2009 Orenco Systems® Inc. NTD-SC-LACEYRev. 1.0, © 6/09

Page 1 of 1

Service ConnectionsTechnical Data Sheet

Applications Orenco® Service Connections are used to isolate pressure mainlines from individual service laterals, by combining a ball valve and check valve into one component. Service connections also help simplify inspection and maintenance procedures.

General Orenco’s Service Connections are constructed of Schedule 80 PVC. All models built for the City of Lacey, WA include a 1-in. diameter inlet elbow and a 1 1/4-in. diameter outlet elbow.

Standard ModelsSC125-LACEY

Nomenclature

Materials of ConstructionPipe Schedule 80 PVCFittings Schedule 80 PVCCheck valve (KBI) Schedule 80 PVCBall valve (KBI) Schedule 80 PVC

SpecificationsA - Width (in.) 3.75B - Overall length (in.) 18.63C - Height (in.) 5.75Inlet diameter (IPS nom.) 1 in.Outlet diameter (IPS nom.) 1.25 in.

Discharge diameter:125 = 1¼ in.

Service connection

125SC - LACEYA

B

C


NCF-CO-LACEY8000WM Rev. 1.0, 08/17

CERTIFICATE OF ORIGIN CITY OF LACEY

Engineered wastewater collection system SMALL COMMUNITY SYSTEM

(Using 8000 Gallon Tank & Wall Mounted (WM) Control Panel) The following Collection System On-Lot Package is certified to have been manufactured by Orenco Systems®, Inc., Sutherlin, Oregon. The On-Lot Package equipment listed below is covered by an extended factory warranty under the terms and conditions of Orenco Systems’ Certificated Products Limited Warranty in effect at the time of sale.

On-Lot Package Code: PSA20-LACEY8000WM

Adhesive: ........................................................................... (4) ADH100

Biotube® Pump Vault: ........................................................ (1) PVU84-3625-L

Float Assembly: .................................................................. (1) MFPGN-39V-50-LACEY

Discharge Assembly: ......................................................... (2) HV100BPRX-80-LACEY

Check Valve: ...................................................................... (2) PPSC-10

Effluent Pump: .................................................................... (2) PF200512-50

Control Panel: .................................................................... (1) DAX2IRRODSFL-LACEY-WM

Homeowner’s Manual: ....................................................... (1) PMHOMEMANUAL

Installation Manual: ............................................................ (1) PMPSPPINST

Certificate of Origin: .......................................................... (1) NCF-CO-LACEY8000WM


PVC Access Risers & Accessories: ................................... (1) RR30XXRLA+(5)10+(2)10-LACEY, (2) RR24XXRLA

Fiberglass Access Lids: ..................................................... (1) FLF30G, (2) FLD24G

Fiberglass Tank: ................................................................. (1) T8000-LACEY

Service Connection Valve Assembly ................................. (1) SC125-LACEY

For Customer Use: Site address:

Lot number:

Development:


Vendor:

City Inspector:


YPGW

DWG. NO.

DWN CKD DATE

CITY ENGINEER

APPROVED


Applications Orenco 84-inch Biotube® Pump Vaults are used to filter efflu-ent that is pumped from septic tanks or separate dosing tanks in STEP systems and onsite wastewater treatment systems. They remove two-thirds of suspended solids, on average. Pump vaults house a Biotube effluent filter and one or two Orenco high-head effluent pumps and can be used in single-compartment septic tanks with flows up to 40 gpm. When flows are greater than 40 gpm, a double-compartment septic tank or separate dosing tank is recommended.

General The Orenco 84-inch Biotube Pump Vault includes a molded polyethylene housing with an internal filter cartridge con-structed of polypropylene and PVC. Schedule 80 PVC support pipes are included to suspend the vault in a tank opening. The filter cartridge can be removed without pulling the pump or the vault. Effluent enters through inlet holes around the perimeter of the Biotube vault and flows through the Biotubes to the external flow inducer. The external flow inducer accom-modates one or two pumps. Orenco Biotube Pump Vaults are covered by U.S. patents #4,439,323 and 5,492,635.


Nomenclature

© 2012 Orenco Systems® Inc. NTD-PVU-LACEY-2Rev. 1.0, © 01/12

Page 1 of 2

84-inch Universal Biotube® Pump VaultsTechnical Data Sheet




Inlet holes

Side view

Support pipe




84 - 36 25PVU

Vault height


- L


DRAW

N BY

: CD

Ore

nco

Syst

ems

Inco

rpor

ated

RDa

te:

6/1/

06

CUST

OM D

RAW

ING:

REVI

SION

:1

Instructions




18

DO NOT GLUE JOINT

USE REINFORCED TOP

PVUP

57-1

819-

L

WOR

K OR

DER

#

APPR

OVED

BY:

MAS

TER:

1391

37

3055

73



Page 2 of 2



Side view cutaway

C

D

Top view

Support pipes

H

F

2" min.

J

G

A

B


Drain valve ball

E


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-MF-MF-LACEY-2Rev. 2.0, © 01/18

Page 1 of 2

Float Switch AssembliesTechnical Data Sheet

Applications Float switches are used to signal liquid level positions for alarm and pump control applications. Orenco float switch assemblies can be mounted in pump vaults, effluent screens, pump basins, and risers.

GeneralAll models listed are UL listed and CSA certified for use in water or sewage.

Floats are typically ordered in assemblies that include one or more floats mounted on a 1-inch PVC float stem. ABS float collars are used to provide secure mounting that is easily adjustable.

Standard ModelsMFPGN-39V-50-LACEY


Materials of ConstructionFloat housing Impact-resistant, noncorrosive PVC plastic for use in liquids up to 140˚ F

Float cord Flexible 2-conductor (UL, CSA), SJOW; water-resistant (CPE); neoprene coating

Float collar ABS

MF 39 50VPGN LACEY- - -

Application:V = pump vault (Lacey, WA float settings)

Cod length:50 = 50 in.

Stem length:39 = 39 in.

Float switch models:P = signal-rated mechanical float switch, normally openG = motor-rated mercury float switch, normally openN = signal-rated mechanical float switch, normally closed

Mechanical or mercury float switch assembly

The “On” and “Off” positions describe normally open floats.

On

Off

Float collar

Float tether

Set point

Draw

down

X

Y

20"25"29"

Float stem

P

G

N


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-MF-MF-LACEY-2Rev. 2.0, © 01/18Page 2 of 2


Notes1 State: normally open or normally closed

The default state of a float — normally open or normally closed — refers to the contact positions in the float when the float is resting (down). Float switches have an internal contact. The terms “normally open” (N/O) and “normally closed” (N/C) refer to the state of the float switch contact in the down position. A normally open float switch has an open contact (off) in the down position and a normally closed float switch has a closed contact (on) in the down position. Different panel functions require different types of float switches. Most applications require float switches that are normally open. One notable exception is the redundant off and low-level alarm function that requires a normally closed float switch, except with MVP and VCOM panels.2 Type

Floats have mechanical or mercury contactor types. The important distinc-tion between these is that mercury floats are not rated for potable water.

3 IR (intrinsically safe relay)

Approved for use with intrinsically safe, Class I, Division 1 applications, where reliable float switch operation with very low current is required. 4 Drawdown

Drawdown (in inches) refers to the difference in liquid level between a float switch’s activation and deactivation points. Drawdown can be altered by adjusting the tether length of the float switch cord. When selecting float switches, keep in mind that any float switch that can directly start and stop a pump (one that has no motor contactor in the control panel) should have a drawdown capability, to avoid rapid cycling of the pump.

Float State1 Type2 IR3 Volts Amps hp Tether X Y Drawdown4

Signal-rated mechanical floats (for control switch applications)

P Model Normally open Mechanical Yes n/a n/a n/a 2.00 in. 1.50 in. 0.50 in. 2.0 in.

N Model Normally closed Mechanical Yes n/a n/a n/a 2.00 in. 1.50 in. 0.50 in. 2.0 in.

Motor-rated floats (for pump switch applications)

G Model Normally open Mercury No 120 V 15A ¾ hp 2.00 in. 1.50 in. 3.00 in. 4.50 in.


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-HV-HV-LACEYRev. 2.0, © 01/18

Page 1 of 1

Discharge AssembliesTechnical Data Sheet

Standard ModelsHV100BPRX-80-LACEY, PPSC-10

Product Code Diagrams

Materials of ConstructionComponent Material

Ball valve Schedule 40 PVC

Flowmatic check valve Stainless steel

Pipe and fittings Schedule 80 PVC

Flexible hose PVC

External flex hose PVC

Flow control disc Schedule 80 PVC

Gate valve Schedule 80 PVC

Unions Schedule 80 PVC

High-pressure flex hose Special elastomer compound

Component Working Pressure RatingsValves 150 psi (10 bar) at 73˚ F (23˚ C)

Unions 150 psi (10 bar) at 73˚ F (23˚ C)

High-Pressure Hose SpecificationsThickness and working pressures at 73˚ F (23˚C) Size Wall Working (Nominal) thickness pressure

1.00 in. 0.235 in. 250 psi

ApplicationsOrenco Discharge Assemblies are used to convey effluent from a pump to the exterior of a riser or pump basin. They come in high-head configuration, for use with submersible turbine pumps. An external flex extension is recommended for installations where tank settling may occur to avoid line breakage during settling. Discharge assemblies for use in 1500-gallon STEP tanks include a ¼-in. flow control orifice.

GeneralOrenco Discharge Assemblies are corrosion-resistant and adjustable for a proper fit. Discharge assemblies are composed of PVC valves and flexible hose that simplify installation and maintenance. The flex-ible hose damps vibrations from the pump and allows for easy instal-lation. All parts are either solvent welded or threaded and sealed with Teflon® paste.

Teflon® is a registered trademark of DuPont.

HV PR 80100 LACEYB X

Schedule 80


PR = High-pressure

B = Ball valve

X = External flex hose

Discharge diameter:100 = 1-in.

- -

PP SC 10

Discharge diameter10 = 1 in.

Stainless steel check valve

Pump part

-

Stainless Steel Check Valve

Hose and Valve Assembly

High-Pressure Hose


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-PU-PF-LACEY-2Rev. 1.0 © 01/18

Page 1 of 2

PF-Series 4-in. Submersible Effluent PumpTechnical Data Sheet

ApplicationsOrenco® 4-in. Submersible Effluent Pumps are designed to transport screened effluent (with low TSS counts) from septic tanks or separate dosing tanks. All of our pumps are constructed of lightweight, corrosion-resistant stainless steel and engineered plastics; all are field-serviceable and repairable with common tools; and all standard 60-Hz PF Series models are CSA certified to the U.S. and Canadian safety standards for effluent pumps, meeting UL requirements.

High-Head Effluent Pumps from Orenco® are used in a variety of applications, including pressurized drainfields, packed bed filters, mounds, aerobic units, effluent irrigation, effluent sewers, wetlands, lagoons, and more. These pumps are designed to be used with a Biotube® pump vault.

Features/SpecificationsOrenco 4-in. Submersible Effluent Pump has the following features:

• Minimum 24-hour run-dry capability (liquid end) with no deteriora-tion in pump life or performance

• 1/8-in. bypass orifice (patent pending) to ensure flow recirculation for motor cooling and to prevent air bind

• Liquid end repair kits available for better long-term cost of ownership

• TRI-SEAL™ floating impeller design

• Super stainless Franklin Electric motor, rated for continuous use and frequent cycling

• Type SOOW 600-V motor cable (suitable for Class I, Division 1 and Division 2 applications)

• Five-year warranty on pump or retrofit liquid end from date of manufacture against defects in materials or workmanship

Standard ModelPF200512-50


Discharge connection

Bypass orifice

Suction connection

Fran

klin

liqui

d en

dFr

ankli

n su

per s

tain

less

mot

or

LR80980LR2053896

PF 20 05 5021

Cord length:50 = 50 ft

PF-series 4-in. submersible effluent pump

Horsepower:05 = 1/2 hp

Nominal flow, gpm:05 = 1/2 hp

Voltage, nameplate:2 = 230 VAC

Frequency:1 = Single-phase, 60 Hz

-


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-PU-PF-LACEY-2Rev. 1.0 © 01/18Page 2 of 2


SpecificationsDesign gpm (in.) 20

Horsepower 0.50

Phase 1

Voltage, nameplate 230

Voltage, actual 240

Design flow amps 6.4

Max amps 6.

Impellers 4

Discharge size1 1 1/4

Length (in.) 22.5

Min. liquid level2 (in.) 18

Weight3 (lb) 32

Rated cycles/day 3001 The 1 ¼-in. NPT discharge is 2 7⁄8-in. octagonal across flats; Discharge is female NPT threaded, U.S. nominal size, to accommodate Orenco® discharge hose and valve assemblies.

2 Minimum liquid level is for single pumps when installed in an Orenco Biotube® Pump Vault or Universal Flow Inducer. In other applications, minimum liquid level should be top of pump. Consult Orenco for more information.

3 Weight includes carton and 50-ft cord.

Materials of Construction Discharge: Glass-filled polypropylene

Discharge bearing: Engineered thermoplastic (PEEK)

Diffusers: Glass-filled PPO (Noryl GFN3)

Impellers: Celcon® acetal copolymer

Intake screen: Polypropylene

Suction connection: Stainless steel

Drive shaft: 7/16 inch hexagonal stainless steel, 300 series

Coupling: Sintered stainless steel, 300 series

Shell: Stainless steel, 300 series

Motor: Franklin motor exterior constructed of stainless steel. Motor filled with deionized water and propylene glycol for constant lubrication. Hermetically sealed motor housing ensures moisture-free windings. All thrust absorbed by Kingsbury-type thrust bearing. Rated for continuous duty. Protected against thermal overload and equipped with surge arrestors for added security.

Tota

l dyn

amic

hea

d (T

DH) i

n fe

etFlow in gallons per minute (gpm)

142 4 6 8 10 16 18 20 22 24 26 28 30120

20

0

40

60

80

100

120

140

160

180

200

220

240

260

280

300

PF Series 60-Hz 0.5 hp

PF200512

Using a Pump CurveA pump curve helps you determine the best pump for your system. Pump curves show the relationship between flow (gpm) and pres-sure (total dynamic head, or TDH), providing a graphical represen-tation of a pump’s optimal performance range. Pumps perform best at their nominal flow rate — the value, measured in gpm, expressed by the first two numerals in an Orenco pump nomencla-ture. At low flow rates, TDH varies from pump to pump, so it is rep-resented as a dashed line in the pump curves. For most accurate pump specification, use Orenco’s PumpSelect™ software.


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-CP-D-LACEY-3Rev. 1.0, © 01/18

Page 1 of 1

Duplex Control Panel Package – Lacey, WATechnical Data Sheet

ApplicationsOrenco® Duplex Control (DAX) Panels are used to control effluent pumps, alarms, and other equipment as specified in pressure sewers and onsite systems.

GeneralOrenco Duplex Control Panels are specifically engineered for pressure sewer (STEP) systems, onsite septic treatment systems, and pump con-trol into gravity sewer systems. Standard features include circuit break-ers, and automatic/manual/off toggle switch, automatic motor control operation, and an audible/visible high water level alarm with auto reset.

Standard ModelsDAX2IRFL-LACEY-FS, DAX2IRFL-LACEY-WM


Enclosure Dimensions FS FS WM Isolation Disconnect Enclosure Pedestal Enclosure Enclosure Enclosure

Height (in.) 36 10 30 20 9

Width (in.) 18 18 21 20 5.5

Depth (in.) 12 12 12 8 2

SpecificationsEnclosure, FS models Strong Box® model B18SS; pedestal model PED-18SS

Enclosure, WM models Fiberglass, Type 4X

Enclosure, Isolation Stainless steel, Type 4X

Enclosure, Disconnect Galvanized steel, type 3R, UL 98 rated

Panel Ratings 240 V, 2 hp, 28 A, single phase, 60 Hz

Motor-Start Contactors 240 V, 28 FLA, 3 hp, 60 hz; 2.5 million cycles at FLA (10 million at 50% of FLA)

Intrinsically Safe Relays 5-channel, 100/240 VAC, UL 698 listed

Duplex Alternator Cross wired style for independent lag pump function; Selector switch for locking one pump into lead position

Controls Circuit Breaker 10 A, OFF/ON switch; Single-pole 120 V; DIN rail mounting with thermal magnetic tripping characteristics

Pump Circuit Breakers 20 A, OFF/ON switches; Double-pole 240 V; DIN rail mounting with thermal magnetic tripping characteristics

Toggle Switches Single-pole, double-throw HOA switches; 20 A, 1hp

Audible Alarm 95 dB at 24 in., warble-tone sound

Visual Alarm 7⁄8-in. diameter red lens, “Push-to-silence;” UL Type 4X rated, 1 W LED light, 120 V

Flashing light 4-in height, 3-in. diameter, UL Type 4X rated, 13 W LED light, 120 V

Redundant Off Relay Provides a secondary off; Sounds alarm on low level condition; DIN rail mount

Disconnect Switch 3-pole, 60 A, 600 V, UL 98 rated

DAX2 DSRO LACEYIR FL

Flashing light

Intrinsically safe relays

Duplex panel, 240 VAC

Mounting option:FS = Free-standing panel packageWM = Wall-mounted panel package

Panel option:DS = Disconnect switch

Panel option:RO = Redunat-off/low-level alarm

- -


Panel Wiring DiagramModel DAX2 IR RO DS FL - LACEY

2017 SUBMITTAL

CB 10A

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

1.10

1.11

1.12

1.13

1.14

1.15

1.16

1.17

1.18

1.19

1.20

1.21

1.22

1.23

1.24

1.25

1.27

1.28

Ground

N

L2

L1

DISCONNECTSWITCH

60A

L1

M1

T2L2

T1L1

M2

T2L2

T1L1

Note: Motors must haveinternal overload protection

Pumps230 VAC / 1 Hp.1 Phase / 60 Hz.

= Factory Wire= Field Wire

L2

NCB 15A

CB 15A

INTRINSICALLYSAFE RELAYIDEC EB3C-R05A

Floats or equivalent devicesmust be purely resistive and

non-energy storing

Maximum cable length frompanel to float is 2,000 feet

Install in accordance with Article504 of the National Electric

Code

Note: A spacing of 2 inches(50mm) must be maintained

between intrinsically safe, andnon-intrinsically safe wiring.

From Main Power Panel240/120 VAC, 1 Phase, 60 Hz.

Main disconnectprovided by others.

PUSH TO SILENCE

NB(OPTIONAL)

CABINET BEACON ALARM LIGHT

AL1

SRA2A1

AUDIBLE ALARM FLOYD BELL SP-1081A -+

SR 1411

SR 1211

LOCAL PUSHBUTTON LEVEL ALARM LIGHTIDEC HW SERIES

RX2X1

ALARM SILENCE RELAYIDECRJ2S-CL-A120

AL1

IR A5C5

CR1 2421

IntrinsicallySafe Section

Non-IntrinsicallySafe Section

Lead PumpOn

Redundant Off/Low Level Alarm

High LevelAlarm

IR

L

P1 P2 P3 P4 P5 N5

N

TL*

LATCING RELAYIDEC RJ2S-CL-A120CR2

A2A1

NRRemote Alarm

Light Alarm

ORENCO AHW REMOTE ALARM BOX(SEE DETAIL ON LEFT)

AL

RA2A1

AA-+

R 1411

R 1211

ALX2X1

AL

ORENCO AHWDETAIL

TL: The installed terminal linkcombines the Lag Pump Onoperation with the High Level

Alarm float. To separate,remove the terminal link.

BL

NR

999594939291

999594939291

Isolation PedestalEnclosure

Isolation PedestalEnclosure

1

2

3

4

1

2

3

4

1

2



1.28

Simplex Operation

High Level Alarm- Lag Pump On/Off: This float activates the alarm light and audible alarm when lifted. The audible alarm may be silenced by pressing the PUSH TO SILENCE button. The alarm light will remain on until the float is lowered.

This float also turns on the Lag Pump. The pump will remain on until the Lag and Lead floats are lowered.

Lead Pump On/Off: This float turns on the Lead Pump when lifted. The pump will continue to run until the float is lowered.

Redundant Off/Low Level Alarm: This float activates the alarm light and audible alarm when lowered. The audible alarm may be silenced by pressing the PUSH TO SILENCE button. The alarm light will remain on until the float is raised. The pumps will not operate during low level alarm.

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

2.10

2.11

2.12

2.13

2.14

2.15

2.16

2.17

2.18

2.19

2.20

2.21

2.22

2.23

2.24

2.25

2.27

2.28

ALTERNATING RELAYSSAC ARP43S

ALT

ALT

63

72

81

OFFHAND AUTO

OFFHAND AUTO

M11314

M21314

M1A2A1

MOTOR CONTACTORABB A16-30-10-84

M2A2A1

MOTOR CONTACTORABB A16-30-10-84

CR1A2A1

IR A1C1 REDUNDANT OFF RELAYIDECRJ2S-CL-A120

CR1 1211 IR A4C4

IR A3C3

IRA2C2


Control PanelEnclosure: Schneider NSYPLM75G

PANEL FRONT30 x 21

PUSH TO SILENCE

MOUNTING PANEL

AUTO

OFF

MAN

AUTO

OFF

MAN

Relay IdecEB3C-R05A

EE

Ju

sti

n W

hit

ed

1

of

1

Mo

de

l D

AX

2 I

R R

O D

S F

L

- L

AC

EY

06

/08

/17

1.0

Dra

win

g N

o.

Da

te:

Title

:

Da

te A

pp

rove

d:

Ap

pro

ved

By:

De

sig

ne

d B

y:

Dra

win

g:

Dra

wn

By:

Re

visi

on

:S

cale

:N

on

e0

6/0

8/1

7

EE

SU

BM

ITT

AL

Q#

06

02

17

JS

2

OT60F3

l ON

O

OFF

2T1 4T2 6T3

1L1 3L2 5L3

Alarm

Cutler HamCircuit Breakers

Idec RelayRJ2S-CL-A120

LLCABB

LLC44A1A

10

0n/I

0ff/

O

0n/I

0ff/

O

0n/I

0ff/

O

20

0n/I

0ff/

O

0n/I

0ff/

O

20

ABBMotor Contactors

ABBDisconnect Switch

Wire Tray

Wire Tray

IntrinsicallySafe Area

J-36

Control PanelEnclosure: Rittal WM202008N6

PANEL FRONT20 x 20 MOUNTING PANEL

EEJu

stin

Whi

ted

1 o

f 1

Isol

atio

n P

edes

tal

06/2

3/17

1.0

Dra

win

g N

o.

Dat

e:

Title

:

Dat

e A

ppro

ved:

App

rove

d B

y:

Des

igne

d B

y:

Dra

win

g:

Dra

wn

By:

Rev

isio

n:S

cale

:N

one

06/2

3/17

EES

UB

MIT

TAL

IntrinsicallySafe Area

95-H

igh

Leve

l/La

g O

n

Pump 1 Pump 2

TL TL TL TL TL

95 9993 9491 92

99-C

omm

on

93-L

ead

On

91-R

O/

Low

Lev

el

1 2 3 4

TL


Quote #: 060217JS2.2

Model: DAX2 IR RO DS FL- LACEY (Fiberglass Version)

10 Digit Manf Number Manufacturer Description QtyParts List

Project: City of Lacey 2017 Standard

Audible Alarms13-16-56-1029 SP-1081 Floyd Bell Alarm; 120V, 95db, Reduced Sensitivity, Extra Fast Warble,

Panel Mount1

Circuit Breakers13-16-11-1014 QCR1010 Cutler Ham Circuit Breaker; 10A, 1P, 120/240V 113-16-11-1020 QCR2020 Cutler Ham Circuit Breaker; 20A, 2P, 120/240V 2Control Switches13-16-66-1034 XTD2B1ABP Eaton Switch; Toggle, 1PDT, On-Off-On, .250 Spade Terminals, 20

Amps @ 125 VAC2

Disconnect SwitchesXX-XX-XX-USER

DPU222R Eaton Pull-Out Disconnect Switch, 60A 2Pole 113-16-66-1376 OT60F3 (Old# OT60E3) ABB Disconnect Switch; 60A, 600V, 3-Pole, UL98 113-16-66-1350 OHYS2AJ1 (Old#

OHY2AJ1)ABB Disconnect Handle; Red/Yellow, 100A, Type 3R 1

13-16-66-1356 OXS6X250 (Old#OXS5X250)

ABB Disconnect Shaft; 9.8", 100A 1EnclosuresXX-XX-XX-USER

WM202008N6 Rittal 316SS Wallmount Enclosure, 20x20x8 113-21-11-1337 NSYPLM75G Schneider Enclosure; 30x21x12, Small, Fiberglass, Type4X 113-21-11-1171 OSI-BP3021A Orenco Sys Backplate; Aluminum, for NSYPLM75 30x21enclosure 113-16-99-1012 C-107-PM Cust. Con. DIN Rail; 1 meter, pre-punched, aluminum .7Lights13-16-36-1500 HW1L-M2F10QD-R-120V Idec Pushbutton; Red, Illuminated, 120V, Complete 113-16-36-1178 AMX15 Ingram Dome Light; Mini, Red, 15W, 120V, Type 4X 113-16-36-1194 SSF150W Ingram Alarm Light; Solid State Flasher SSF150W 1MiscXX-XX-XX-USER

PSTPS500EH10Ss Platt 14GA 316SS Unistrut 10FT 1XX-XX-XX-USER

1300990462 Woodhead Non Metallic Relief with Mesh 5XX-XX-XX-USER

Misc-Alum Barrier Orenco Aluminum Barrier for Main Panel 1XX-XX-XX-USER

Misc-Alum2 Orenco Aluminum Barrier For Isolation Pedistal Box 1XX-XX-XX-USER

5602 Woodhead Locknut for 1300990162 5XX-XX-XX-USER

5612 Woodhead Gasket Seal For 1300990162 5XX-XX-XX-USER

1301800333 Woodhead O Ring For 1300990161 5Motor Contactors/Starters13-16-16-1304 AX18-30-10-84 ABB Contactor; 18A, 3P, 110 - 120V, 50/60 HZ 2Relays13-16-46-1073 RJ2S-CL-A120 Idec Relay; 120V, DPDT, 8A, Indicator 313-16-46-1283 SJ2S-07LW Idec Socket; 8 Pin, DIN/Pnl Mt, for RJ Relays 313-16-46-1116 EB3C-R05AN Idec Relay; Intrinsic barrier, 5 channel, 100/240v AC, UL listed 113-16-46-1160 ARP 43S Littelfuse Relay; Alternating, 120V, DPDT, 8-Pin, Selector 113-16-46-1290 SR2P-05C Idec Socket; 8-Pin, 2P, 300V, Touch Safe 1Terminal Blocks13-16-71-1450 3044131 (UT-6) Phoenix Terminal Block; 24/8AWG, 50A, 1P, 1000V, 8.2mm 1013-16-71-1480 0800886 Phoenix Terminal Block; End Block, ENS 35N 213-16-71-1490 3003020 Phoenix End Cover; D-UK 4/10 (UK 5 & 6) 113-16-71-1502 0200059 Phoenix Jumper; 3-Pole, UK6 1XX-XX-XX-5563 misc Phoenix PHO Number 10


Air Conditioning DisconnectsFused and Non-Fused Pullouts• ON/OFF control provided by a

pullout handle

• Pullout handle can be conve-niently stored in the compart-ment in the OFF position,helping to prevent the handlefrom being misplaced

• Protective shield cannot beremoved until the pullouthandle is removed,disconnecting the power

Molded Case Switch• Rugged molded case

construction in a disconnectswitch that looks like a circuitbreaker but operates likean ordinary household lightswitch

• Plug-in molded case switch(included) eliminates the needfor pullout handles

• No need for replacementpullout handles due to lossor theft

Eaton’s product offering:• 3 Standard Designs:

• Non-Fused

• Fused

• Molded Case Switch

• Enclosure:

• NEMA 3R (outdoor)

• Metallic (galvanized/painted)

• Non-metallic (plastic)

• Ratings:

• Single-phase, two-wire,240Vac

• Three-phase, three-wire,240Vac

• 30 and 60 amps

• Optional ACDs with GroundFault Receptacles or Weather-Resistant/Tamper-ResistantReceptacles are available

Eaton Air Conditioning Disconnects

Air Conditioning Disconnects (ACD) are located between a loadcenter (distribution panel) and an air conditioner. ACDs provide a visible disconnecting means when perform-ing maintenance and are commonly referred to as disconnects, pullouts or air conditioning switches.

Applications: • Air conditioners

• Heat pumps

• Water heaters

• Other locations where a localdisconnect is required


Eaton CorporationElectrical Sector1111 Superior Ave.Cleveland, OH 44114United States877-ETN-CARE (877-386-2273)Eaton.com

© 2012 Eaton CorporationAll Rights ReservedPrinted in USAPublication No. PA00701002EFebruary 2012

All other trademarks are property of their respective owners.

Non Fused Pullouts

Max. hp rating

Main Ampere Rating 120V 240V

Wire Size Range Cu/Al 60C or 75C Catalog Number

Galvanized Steel

60 - 10 #14-3 DPU222R

Non-Metallic/Polycarbonate Enclosure

60 - 10 #14-2 ACD222URNM-A2

Fused Pullouts

Max. hp rating



Galvanized Steel

30* 2 3 #14-3 DPF221R

60* 3 10 #14-3 DPF222R

Non-Metallic

30 2 3 #14-2 ACD221RNM-A2

60 3 10 #14-2 ACD222RNM-A2

Molded Case Switch

Max. hp rating



Galvanized Steel

60 - 10 #14-3 DPB222R

Non-Metallic/Polycarbonate Enclosure

60 - 10 #14-2 B60NARNM-A2

Three-Phase Non-Fused ACD

Max. hp rating

Main Ampere Rating 240V 480V Wire Size Range Cu 75C Catalog Number

Galvanized Steel

60 15 30 #14-4 DPU362RA

ACD with 20 Ampere Ground Fault Receptacle

Max. hp rating



Non-Fused Pullouts

60 - 10 #14-3 DPU222RGF20WRTR

60 - 10 #14-3 DPU222RGF20

Fused Pullouts

30 2 3 #14-3 DPF221RGF20WRTR

30 2 3 #14-3 DPF221RGF20

60 3 10 #14-3 DPF222RGF20WRTR

60 3 10 #14-3 DPF222RGF20

ACD with 15 Ampere Ground Fault Receptacle

Max. hp rating



Non-Fused Pullouts

60 - 10 #14-3 DPU222RGF15WRTR

60 - 10 #14-3 DPU222RGF15

Fused Pullouts

30 2 3 #14-3 DPF221RGF15WRTR

30 2 3 #14-3 DPF221RGF15

60 3 10 #14-3 DPF222RGF15WRTR

60 3 10 #14-3 DPF222RGF15

*To obtain a Service Entrance rating, the addition of a ground bar kit is required.


© 2009 Orenco Systems® Inc. NTD-RLA-RR-LACEYRev. 1.0, © 6/09

Page1 of 1

Access Risers Technical Data Sheet

GeneralOrenco Access Risers are constructed of ribbed PVC pipe and are available in 24-in. and 30-in. diameters. The 24-in. ribbed ris-ers are available in three-inch increments up to 14 ft in length. The 30-in. risers are available in one-inch increments up to 13 ft in length.

Standard ModelsRR24XX, RR30XX

Nomenclature

ApplicationsOrenco’s Access Risers provide access to septic tank openings and can be cast into the tops of concrete tanks, bonded in place, or bolted down using a riser tank adaptor. They can also be used as valve enclosures.

Materials of ConstructionRibbed Risers: PVCBolt catch (30" risers only) PVC

SpecificationsModel RR24XX RR30XXI.D. (in.) 23.50 29.50Wall Thickness - excluding ribs (in.) 0.20 0.20O.D. - including ribs (in.) 25.63 31.00Weight per foot (lb) 19 18

Riser diameter:24 = 24 in. 30 = 30 in.

Riser height, inches

Ribbed riser

RR


© 2008 Orenco Systems® Inc. NTD-RLA-RLA-LACEYRev. 1.0, © 6/09

Page 1 of 1

RLA Riser-to-Lid AdaptersTechnical Data Sheet

ApplicationsOrenco® riser-to-lid adapters (RLAs) provide a secure, water-tight method of attaching an Orenco fiberglass lid to a 24-in. or 30-in. ribbed PVC access riser.

RLAs are especially useful when the top of the riser is uneven or has a damaged edge.

GeneralRLA adapters can be attached to 24-in. or 30-in. risers to sim-plify bolting a lid to the riser.

Standard ModelsRLA24, RLA30

Nomenclature

Materials of ConstructionAdapter ABSO-ring EPDM SpecificationsDimensions in inches (mm) RLA24 RLA30

A – Adapter height 1� (32) 1� (32)

B – Socket or lip width 1 (25) 1 (25)

C – Inside diameter 227⁄8 (581) 28⇥ (724)

D – Outside diameter 25⇥ (648) 31 (787)

E – Socket depth 3⁄8 (10) N/A

Riser style Perma-Loc™ Perma-Loc Ultra-Rib™

Lid bolt

RLA24 adapter

24-in. riser

Fiberglass lid


DC

A

BE


30-in. riser

Lid bolt

RLA30 adapter

Fiberglass lid

DC

A

B

RLA

Riser-to-lid adapter

Adapter diameter (inches):24 = 24"30 = 30"


Pipe GrommetsGeneralOrenco Pipe Grommets are constructed of corrosion-resistant rub-ber to provide long-lasting seals. Grommets conform to standardIPS sizes. Not all models conform exactly to the depiction shown.

Standard ModelsG05L, G075L, G1L, G125L, G150L, G2L, G3L, G4L, G6L

Nomenclature


ODID

GW

GD

T

SpecificationsDimensionsModel G05L G075L G1L G125L G150L G2L G3L G4L G6LOD (inches) 1 1/4 1 1/2 1 7/8 2 1/8 2 1/2 3 7/8 5 6 8 1/8ID (inches) 3/4 1 1 1/4 1 1/2 1 3/4 2 1/8 3 1/4 4 3/16 6 11/16GD (inches) 1 1 1/4 1 5/8 1 3/4 2 1/8 2 11/16 3 13/16 4 15/16 7 5/8GW (inches) 3/16 3/16 1/4 1/4 1/4 5/16 5/16 1/4 1/4T (inches) 1/2 7/16 9/16 5/8 5/8 15/16 15/16 7/8 13/16Holesaw Size (inches) 1 1 1/4 1 9/16 1 3/4 2 1/8 2 3/4 3 7/8 5 7

Material of Construction:

EPDM synthetic rubber in accordance with MIL-STD-417, 60 durometer.

NSU-RLA-PG-1Rev. 3.4, © 7/03

ApplicationsOrenco Pipe Grommets are used to provide a seal to prevent thepassage of liquids through pipe ports.

G

Indicates grommet diameter:05 = 1/2"075 = 3/4"1 = 1"125 = 1-1/4"150 = 1-1/2"2 = 2"3 = 3"4 = 4"6 = 6"

Grommet

LIndicates not installed



Page 1 of 1

FLF-Series Fiberglass Access LidsTechnical Data Sheet

ApplicationsOrenco® FLF-Series Fiberglass Access Lids provide a secure cover-ing for risers, pump basins, and access ports. They are capable of supporting a 2500-lb (1134-kg) wheel load; however, they are not designed or recommended for vehicular traffic. FLF-series lids will fit directly onto the riser types listed in the Specifications section.

FLF30 lids are required for retrofits on 30-in. (750-mm) Perma-Loc™ access risers or 30-inch (750-mm) Orenco RLA riser-to-lid adapters.

GeneralOrenco FLF-Series Fiberglass Access Lids are molded using fiberglass reinforced polyester resin with a structural foam core for added dura-bility and longevity. The finish is green or brown and the top surface is textured to provide a nonskid surface. Gasketed lids include a polyurethane gasket. FLF Lids come with four 5⁄16-inch stainless steel flathead socket cap screws and a hex key wrench.

Standard ModelsFLF18G, FLF21G, FLF30G



Core Structural foam

Gasket Polyurethane

SpecificationsModel FLF18G FLF21G FLF30G

Lid O.D. in. (mm) 20.25 (514) 22.5 (572) 32.6 (829)

Groove I.D. in. (mm) 17.50 (445) 20.25 (514) 28.75 (730)

Avg. thickness in. (mm) 0.75 (19) 0.75 (19) 1.0 (25)

Weight lb (kg) 4.15 (1.8) 6.25 (2.8) 11.50 (5.2)

Applications Ultra-Rib™ Ultra-Rib Perma-Loc™ Perma-Loc Kor Flo™

BottomTop

Cutaway view

Core Groove I.D. Gasket Lid O.D.

FLF

Color and logo options:Blank = green color lidB = brown color lidC = custom logoATX = AdvanTex® logo

Lid options:G = gasketV = ventCF = carbon filter installed in lidI2 = 2-in. (50-mm) insulation*I4 = 4-in. (100-mm) insulation

-


Fiberglass lid, FLF-series

* Lid insulation has an R-value of 10 per 2-inch (50-mm) incrementNote: For fiberglass basin bottoms without holes, order FLF18 or FLF21




Page 1 of 1

DuraFiber™ Access LidsApplicationsOrenco® DuraFiber™ Access Lids provide a secure, damage-resistant covering for ribbed PVC and HDPE risers, pump basins, and access ports. They are not recommended for vehicular traffic. 24-inch (600-mm) DuraFiber lids require an RLA24 adapter to mate to 24-inch (600-mm) Perma-Loc™ pipe. 30-inch (750-mm) DuraFiber lids are not compatible with 30-inch (750-mm) RLA Riser-Lid-Adapters or 30-inch (750-mm) Perma-Loc pipe. For these products, use Orenco’s FLF-Series lids.

GeneralDuraFiber Access Lids are constructed of resin-infused fiberglass fabrics for extreme durability and damage resistance, with breaking strengths in excess of 20,000 pounds (9,000 kg).

They feature flat-style flanges for easier access, allowing clean, flush-to-grade installations. They have cored centering rings for aligning lids with risers. They also have urethane gaskets to help provide watertight seals.

DuraFiber Lids feature a non-skid surface for better grip and aesthet-ics, a molded-in caution statement, and room for a customer logo. They come with four 5⁄16-inch stainless steel flathead socket cap screws and a hex key wrench.

Durafiber Lids are available with optional insulation, installed at the fac-tory or in kits that can be installed in the field.

Standard ModelsFLD24G, FLD24GATX, FLD24GW, FLD30G, FLD30GATX, FLD30GW

Product Code Diagram FLD

Insulation:*Blank = no insulationI2 = 2-inch (50-mm) insulation installedI4 = 4-inch (100-mm) insulation installed

Vent and filter options:Blank = no vent or filter optionsV = ventCF = carbon filter

Gasket options:G = gasket (standard) Blank = no gasket

Lid diameter, in. (mm):24 = 24 (600)30 = 30 (750)

DuraFiber™ fiberglass lid

* Insulation has an R-value of 10 per 2-inch (50-mm) increment.

Color and logo options:Blank = green color lidB = brown color lidC = custom logoATX = AdvanTex® logoW = warning label

Materials of Construction:Lid Fiberglass reinforced polyester

Gasket Urethane

Centering ring core Structural foam

Mounting hardware Stainless steel

Insulation (optional) Closed-cell foam

Insulation mounting hardware Stainless steel

Specifications Model FLD24XX FLD30XX

A in. (mm) 26 (660) 33 (838)

B, in. (mm) 1½ (38) 1½ (38)

C, in. (mm) 23¼ (590) 29¼ (743)

Gasket width, in. (mm) ¾ (19) ¾ (19)

Bolt hole diameter, in. (mm) 5⁄16 (8) 5⁄16 (8)

Weight, lbs (kg) 11 (5) 20 (9)

Bolt holes, per lid 4 4

B

A

C


© 2009 Orenco Systems® Inc. NTD-SC-LACEYRev. 1.0, © 6/09

Page 1 of 1

Service ConnectionsTechnical Data Sheet

Applications Orenco® Service Connections are used to isolate pressure mainlines from individual service laterals, by combining a ball valve and check valve into one component. Service connections also help simplify inspection and maintenance procedures.

General Orenco’s Service Connections are constructed of Schedule 80 PVC. All models built for the City of Lacey, WA include a 1-in. diameter inlet elbow and a 1 1/4-in. diameter outlet elbow.

Standard ModelsSC125-LACEY

Nomenclature

Materials of ConstructionPipe Schedule 80 PVCFittings Schedule 80 PVCCheck valve (KBI) Schedule 80 PVCBall valve (KBI) Schedule 80 PVC

SpecificationsA - Width (in.) 3.75B - Overall length (in.) 18.63C - Height (in.) 5.75Inlet diameter (IPS nom.) 1 in.Outlet diameter (IPS nom.) 1.25 in.

Discharge diameter:125 = 1¼ in.

Service connection

125SC - LACEYA

B

C


NCF-CO-LACEY8000FS Rev. 1.0, 08/17

CERTIFICATE OF ORIGIN CITY OF LACEY

Engineered wastewater collection system SMALL COMMUNITY SYSTEM

(Using 8000 Gallon Tank & Free Standing (FS) Control Panel) The following Collection System On-Lot Package is certified to have been manufactured by Orenco Systems®, Inc., Sutherlin, Oregon. The On-Lot Package equipment listed below is covered by an extended factory warranty under the terms and conditions of Orenco Systems’ Certificated Products Limited Warranty in effect at the time of sale.

On-Lot Package Code: PSA20-LACEY8000FS

Adhesive: ........................................................................... (4) ADH100

Biotube® Pump Vault: ........................................................ (1) PVU84-3625-L

Float Assembly: .................................................................. (1) MFPGN-39V-50-LACEY

Discharge Assembly: ......................................................... (2) HV100BPRX-80-LACEY

Check Valve: ...................................................................... (2) PPSC-10

Effluent Pump: .................................................................... (2) PF200512-50

Control Panel: .................................................................... (1) DAX2IRRODSFL-LACEY-FS

Homeowner’s Manual: ....................................................... (1) PMHOMEMANUAL

Installation Manual: ............................................................ (1) PMPSPPINST

Certificate of Origin: .......................................................... (1) NCF-CO-LACEY8000FS


PVC Access Risers & Accessories: ................................... (1) RR30XXRLA+(5)10+(2)10-LACEY, (2) RR24XXRLA

Fiberglass Access Lids: ..................................................... 1) FLF30G, (2) FLD24G

Fiberglass Tank: ................................................................. (1) T8000-LACEY

Service Connection Valve Assembly ................................. (1) SC125-LACEY

For Customer Use:

Site address:

Lot number:

Development:


Vendor:

City Inspector:


YPGW

DWG. NO.

DWN CKD DATE

CITY ENGINEER

APPROVED


Applications Orenco 84-inch Biotube® Pump Vaults are used to filter efflu-ent that is pumped from septic tanks or separate dosing tanks in STEP systems and onsite wastewater treatment systems. They remove two-thirds of suspended solids, on average. Pump vaults house a Biotube effluent filter and one or two Orenco high-head effluent pumps and can be used in single-compartment septic tanks with flows up to 40 gpm. When flows are greater than 40 gpm, a double-compartment septic tank or separate dosing tank is recommended.

General The Orenco 84-inch Biotube Pump Vault includes a molded polyethylene housing with an internal filter cartridge con-structed of polypropylene and PVC. Schedule 80 PVC support pipes are included to suspend the vault in a tank opening. The filter cartridge can be removed without pulling the pump or the vault. Effluent enters through inlet holes around the perimeter of the Biotube vault and flows through the Biotubes to the external flow inducer. The external flow inducer accom-modates one or two pumps. Orenco Biotube Pump Vaults are covered by U.S. patents #4,439,323 and 5,492,635.


Nomenclature


Page 1 of 2

84-inch Universal Biotube® Pump VaultsTechnical Data Sheet




Inlet holes

Side view

Support pipe




84 - 36 25PVU

Vault height


- L


DRAW

N BY

: CD

Ore

nco

Syst

ems

Inco

rpor

ated

RDa

te:

6/1/

06

CUST

OM D

RAW

ING:

REVI

SION

:1

Instructions




18

DO NOT GLUE JOINT

USE REINFORCED TOP

PVUP

57-1

819-

L

WOR

K OR

DER

#

APPR

OVED

BY:

MAS

TER:

1391

37

3055

73



Page 2 of 2



Side view cutaway

C

D

Top view

Support pipes

H

F

2" min.

J

G

A

B


Drain valve ball

E


Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-MF-MF-LACEY-2Rev. 2.0, © 01/18

Page 1 of 2

Float Sw

Documents

APPENDIX J - Lacey, Washington€¦ · CF-CO-LACEY-1 Rev. 5.0, 01/2018 CERTIFICATE OF ORIGIN City of Lacey Engineered Wastewater Collection System Single Family Residence using 1500