7/30/2019 Apr-Adm2 Installer for Digiplex

1/2

INTRODUCTION

The Voice-Assisted Arm/Disarm Bus Module allows the user to arm

or disarm their security system as well as activate or deactivate In

Touchs PGM from any touch-tone telephone. The APR-ADM2

uses detailed voice prompts to guide the user. Due to the Auto-panel Recognition feature, the In Touch can be connected to either

the Spectra (V2.0 or higher) or Digiplex control panels.

TECHNICAL SPECIFICATIONS

Operating Voltage: 9 - 15VDC

Current Consumption: Typical: 70mA

Maximum: 105mA (with PGM enabled)

Power Consumption: 1 Watt

PGM Outputs: 1 form C relay rated @ 125V, 5A

receptive load

Operating Temperature: 0C to 50C (32F to 122F)

Compatible Telephone: DTMF (Touch-tone)

Compatibility: Any Digiplex control panel

INSTALLATION

The APR-ADM2 is connected to Digiplexs communication bus.

Connect the four terminals labeled 12VDC, GND, GRN, and YEL

of the APR-ADM2 to the corresponding terminals of the Digiplex

control panel as shown in Figure 1. Please refer to the Digiplex

Reference & Installation Manual for the maximum allowable

installation distance from the control panel.

Connect In Touchs RING terminal to Digiplexs R1 terminal and

the TIP terminal of the In Touch to the T1 terminal of the Digiplex

control panel as shown in Figure 1. If the household telephone is

sharing the telephone line with Digiplex and APR-ADM2, connectthe house-hold telephone to the R-1 and T-1 terminals of the bus

module as shown in Figure 1.

Connect APR-ADM2s PGM as shown in Figure 2.

If the control panel is configured to report Arming and

Disarming events and if the In Touch and control panel

share the same telephone line, the users call will be

interrupted during use.

AUTO-PANEL RECOGNITION

This is a feature that allows In Touch to be used with either

Spectra or Digiplex. When connected to the bus, the APR-ADM2

will automatically detect which system it is connected to and adj

its internal communication parameters accordingly. It allows

Touch to be connected to any Digiplex control panel as well as a

Spectra control panel V2.0 or higher.

If connecting the APR-ADM2 to a Spectra control panel, refer

the Spectra APR-ADM2 Reference & Installation Manual.

PROGRAMMING METHOD

To access the In Touch programming mode:

APR-ADM2 can also be programmed using Digiplexs Mod

Broadcastfeature as well as through the WinLoad Software. Re

to the Digiplex Reference & Installation Manual for mo

information on the Module Broadcast feature and to WinLoa

Online Help for information on programming with WinLoad. T

bus modules serial number can be found on its PC board.

NUMBEROF RINGS

Sect ion [001][001]

The value (001 to 255, 000 = disabled) programmed in sect

[001] represents the number of rings the APR-ADM2 will w

before picking-up the line. If the line is not answered after t

number of programmed rings, In Touch will answer the call.

Be sure to program the APR-ADM2 modules number

rings to be less than the number of rings programmed in t

Digiplex control panel or enter000 as the number of rin

for the Digiplex.

ANSWERING MACHINE OVERRIDE

Sect ion [002][002]

If the In Touch uses a telephone line that uses an answer

machine or service, the Answering Machine Override must

programmed. The value (010 to 255 seconds, 000 = disable

programmed in section [002] represents the delay period that AP

ADM2 will wait between the first and second call. The user calls

In Touch, hangs-up, and then calls back within the va

programmed in section [002]. If the APR-ADM2 is called ba

within the programmed delay period, the bus module will overr

the answering machine or service by picking-up the line on the f

ring.

PGM TIMER

Sect ion [003][003]

When the PGM is activated by a user, the value (001 to 255, 000

No Timer) programmed in section [003] determines the time t

APR-ADM2s PGM will remain activated. Once the time value

in section [003] has elapsed, the PGM will deactivate. If a value

000 is entered into section [003], the PGM will remain activat

until it is manually deactivated by the user.

Option [4] in section [004] determines whether the PG

Timer programmed in section [003] is in seconds

minutes.

STEP 1: Press and hold the [0] key

STEP 2: Enter the [INSTALLERCODE]

STEP 3: Enter section [953]

STEP 4: Enter the APR-ADM2s 8-digit [SERIALNUMBER]

STEP 5: Enter the 3-digit [SECTION] you want to program

STEP 6: Enter the required data

7/30/2019 Apr-Adm2 Installer for Digiplex

2/2

PGM OUTPUT

Sect ion [004][004] - opt ion [3][3]

If option [3] in section [004] is on, the APR-ADM2 PGM output is

enabled and can be used. If option [3] in section [004] is off, the

APR-ADM2 PGM output is disabled and cannot be used.

PGM TIME BASE SELECTION

Sect ion [004][004] - opt ion [4][4]

This option determines whether the PGM Timer will be in secondsor minutes. If option [4] in section [004] is off, the PGM Timer will

be in seconds. If option [4] in section [004] is on, the PGM Timer

will be in minutes.

PARTITION ASSIGNMENT

Sect ion [005][005] - opt ions [1][1] to [4][4]

In Touch will only access the partitions that have been assigned to

it and ignore the partitions that have not. Section [005], options [1]

to [4] represent partitions 1 to 4 respectively. To assign a partition

to the APR-ADM2 module, enable the option that corresponds to

the desired partition.

Figure 2: Installing In Touch sPGM

Figure 1: Installing the In Touch