VERANDA 5’x10’RT Wall Mount

Assembly and Operation Guide

www.treasuregarden.com

©2016 Treasure Garden, Inc. - All Rights Reserved. Rev. 10/16

Thank you for your purchase of Treasure Garden’s Veranda Wall Mount Umbrella.

Please remove all contents from the package, inspect and review checklist. CAUTION: To reduce personal injury and damage to your umbrella, read and follow thisassembly and operation guide. We recommend a two-person team for assembly anddisassembly. Save information for future reference. We suggest consulting a licensedcontractor for proper mounting.

101

A - 36” Mounting Track G - Lock Block with (2) Set Screws B - Screw Anchors and Washers (4) - 3/8” x 3” H - Protective Cover

(not included) I - Protective Cover Lock Blocks (2)C - Lag Bolts and Washers (4) - 3/8” x 3” J - Tapping Screws (4)

(not included) K - Allen Wrench - 4mmD - Veranda Umbrella L - Allen Wrench - 6mmE - HingeF - Hinge Screw and Locknut

CHECKLIST

WARRANTY:Treasure Garden warrants this product(in residential use) to be free fromdefects in original materials andworkmanship for a period of 2 year fromthe date of purchase. If a defect in theoriginal material or workmanshipappears during the warranty period;Treasure Garden will (at its option) repairor replace the product without charge.

Simply contact your original authorizedTreasure Garden dealer with adescription of the defect. The dealer willverify the defect and work closely withTreasure Garden to obtain the necessaryservice. In many cases, simple problemscan be solved with a replacement partthat can be shipped directly to the dealerfor professional installation / repair.

In the event that warranted factoryservice is required, Treasure Garden willassume the responsibility of the return

freight charges on warranted product forthe first year only.

Returned product that (upon receipt andinspection) is deemed to be “notcovered” under our warranty, will beshipped / billed at your expense.

This warranty gives you specific legalrights, and you may have other rightswhich vary from state to state.

RUST: Rust is a natural part of theaging process of steel or iron basedmaterials, and is therefore NOTconsidered a defect.

NOTE: Failure caused by unreasonableor abusive use, or failure caused byneglect of reasonable and necessarycare are not covered by this warranty.

Additionally, acts of nature (including butnot limited to wind, hurricanes,tornadoes, and storms) are not coveredby this warranty.

IMPORTANT:

Prior to assembly it is important to decide on the location of the umbrella.

• Allow ample height to avoid damage to your umbrella during assembly and usage.

Storage:

• Properly store umbrella when not in use. Close umbrella, tie string around canopy, coverumbrella with provided protective cover and tie cover handles to protective cover lockblocks. Or remove structure from mounting track and properly store structure.

NOTE: Some parts may be included in the styrofoam packaging. DO NOT discard any packaging or box until assembly is complete.

A -

B -

D -

C -

E -

F -

G -

I - J -

H -

K -

L -

29

S A F E T Y P R E C A U T I O N S :• Close the umbrella in windy conditions or when a storm approaches. Never allow the umbrella to flap in the wind; this could damage the canopy.

• Properly store umbrella when not in use. Close umbrella, tie string around canopy andcover umbrella with provided protective cover.

• Do not leave open umbrella unattended. If damage occurs, this is not covered by the warranty.

• When adjusting the umbrella, make sure that no person(s) or item(s) are close to theumbrella. This is important to prevent injury or material damage.

C A R E A N D M A I N T E N A N C E :• When not in use, close and cover umbrella with a protective cover. • If necessary, clean the fabric with lukewarm water, mild detergent, and a sponge.• Allow a wet canopy to dry slightly opened, but do not leave unattended.• Wipe sliding marks on the aluminum poles with a damp cloth.

Winter Storage:• Store in a dry place.• Any visible defects must be repaired by a professional.

After the Winter:• Areas subject to turning and sliding can be treated with a non-staining lubricant spray(silicone-based).

• Check the condition and function of the umbrella. Any defects must be repaired by aprofessional.

S T E P 1 Locate StudsLocate studs in the area which the track will be installed.

S T E P 2 Position TrackPosition track level on wall at desired height and location. Allow ample height and width toavoid damage to your umbrella during assembly and operation. Place bolt holes at center ofstuds and mark. If holes in track do not line up with existing structural supports, new holescan be drilled into the track to accommodate lag bolts.

S T E P 3 Drill HolesRemove track and drill 1/4” holes into the wall about 3” into the studs. This will preventframe from splitting while installing the lag bolts. NOTE: Shims or spacers may need to beadded on angled sliding. Silicone cocking may be added to the holes before bolts areinstalled to prevent water from penetrating wall.

MOUNTING TRACK

Mounting on wood frame walls wood, vinyl, stucco or aluminum sliding, proceed below.

Mounting on masonry, brick or concrete walls, proceed to page 4.

Centerof Stud

Drill 1/4” Holes in 2 places on each side of track

Stud

Centerof Stud

StudWall

16” On Center

Mounting on wood frame walls with wood, vinyl, stucco or aluminumsliding:

83

S T E P 4 Install TrackUsing a 9/16” socket, install the track with the four 3/8” x 3” lag bolts and washers (notincluded). While tightening the lag bolts, keep the track level. Do not overtighten the lag bolts;doing so may split the wood frame or weaken the lag bolt. Consult a licensed contractor forbolts that fit these types of applications.

Lag Bolt

Lag Bolt

Track

Shim

Siding

Shim

Stud

insi

de w

all

3/8” x 3”Lag Bolt

Lag Bolt

Track

Washer

Stud

insi

de w

all

3”

With ShimsWithout Shims

NOTE: For vinyl or aluminum sliding,shimming beneath the siding under thetrack may provide a more solid surfacefor mounting.

CAUTION: It is critical that you fasten two lag bolts at each end of the track to studs, headeror other major structural members in the wall. Consult a licensed contractor for bolts that fitthese types of applications.

WARNING: Failure to properly fasten mounting track to wall could result the umbrella tocollapse causing property damage and/or personal injury. We suggest consulting a licensedcontractor for proper mounting.

To Attach Umbrella Light: (sold separately)

Open the umbrella light by holding firmly with one hand and then depress the clamp releasebutton with the other hand to release the clamp lock. Open up the light and clasp aroundthe light adapter post. Snap to close. NOTE: It is not necessary to remove light to closeumbrella.

Features

S T E P 6 Protective Cover and Lock Block AssemblyInstall (2) protective cover lock blocks with (4) supplied tapping screws onto wall. Tiecanopy string around canopy to secure canopy. Slide protective cover over canopy usinginserted rod as a guide. Pull down on zipper pole to close protective cover. Secure with (2)protective cover handles to lock blocks installed on wall.

47

S T E P 1 Position TrackPosition track level on wall at desired height and location. Mark bolt holes on concrete ormain body of brick. If holes in track do not line up with existing structural supports, new holescan be drilled into the track to accommodate screw anchors.

S T E P 2 Drill HolesRemove track and drill 1/4” holes into wall about 3” deep and remove any loose concreteinside hole. Do not allow the holes to become tapered or oversized while drilling. Siliconecocking may be added to the holes before or after anchors are installed to prevent waterfrom penetrating wall.

S T E P 3 Install TrackUsing a 9/16” socket, install the track with the (4) 3/8” x 3 screw anchors and washers (notincluded). While tightening the screw anchors, keep the track level. Consult a licensedcontractor for bolts that fit these types of applications.

Brick

Correct

Incorrect

S T E P 4 Close VerandaRemove pin from hub. Pull on hub to unlock from center pole and guide hub down untilumbrella is fully closed. Tie canopy with supplied string to secure.

Mounting on masonry, brick or concrete walls:S T E P 3 Open VerandaGently pull ribs slightly outward, while grabbing hub. Push hub upward, through center poleuntil hub locks into place. Slide pin into hub for extra support.

MountedTrack

S T E P 5 Adjust PositionWhile in closed position, loosen hexagon set screws on hinge and adjust frame position bysliding hinge left or right on mounting track to desired location. To secure, tighten set screws.

MountedTrack

65

WARNING: Some brick walls may not be strong enough to safely support a Verandaumbrella. Screw Anchors are not designed to attach to veneer brick wall or soft bricks. Wesuggest consulting a licensed contractor for proper mounting.

WARNING: Failure to properly fasten mounting track to wall could result the umbrella tocollapse causing property damage and/or personal injury.

CAUTION: Screw anchors are not designed for use in the joints between two bricks. They areONLY to be installed within main body of a brick and not within 1/2” of an outer edge of thebrick. The screw anchors are also not suited for hollow cinder block type construction or wallsurfaces that have deteriorated. Consult a licensed contractor for bolts that fit these types ofapplications.

3/8” x 3”Screw Anchor

Screw Anchor

Track

Washer

3”

Joint

Joint

Brick

INSTALLING VERANDA

S T E P 2 Attach Veranda toMounted Track

Carefully lift and clip Veranda into mountedtrack on wall to your desired location. Note:Hinge will only clip onto track one way.Remove set screws from lock block. Slide lockblock into bottom on hinge until flush. Insertset screws through bottom of hinge into lockblock. Tighten set screws with supplied 4mmallen wrench to secure into place. NOTE: Donot over tighten set screws.

MountedTrack

S T E P 1 Attach Hinge to VerandaAttach hinge to Veranda main frame with the track side facing outward. Secure together usingsupplied (1) hinge screw and (1) locknut. Note: Hinge screw only inserts one way. Tightenlocknut with supplied 6mm allen wrench.

Hinge

Main Frame

InsertHinge Screw

Lock Block

Set Screws

MountedTrack

MountedTrack

65

WARNING: Some brick walls may not be strong enough to safely support a Verandaumbrella. Screw Anchors are not designed to attach to veneer brick wall or soft bricks. Wesuggest consulting a licensed contractor for proper mounting.

WARNING: Failure to properly fasten mounting track to wall could result the umbrella tocollapse causing property damage and/or personal injury.

CAUTION: Screw anchors are not designed for use in the joints between two bricks. They areONLY to be installed within main body of a brick and not within 1/2” of an outer edge of thebrick. The screw anchors are also not suited for hollow cinder block type construction or wallsurfaces that have deteriorated. Consult a licensed contractor for bolts that fit these types ofapplications.

3/8” x 3”Screw Anchor

Screw Anchor

Track

Washer

3”

Joint

Joint

Brick

INSTALLING VERANDA

S T E P 2 Attach Veranda toMounted Track

Carefully lift and clip Veranda into mountedtrack on wall to your desired location. Note:Hinge will only clip onto track one way.Remove set screws from lock block. Slide lockblock into bottom on hinge until flush. Insertset screws through bottom of hinge into lockblock. Tighten set screws with supplied 4mmallen wrench to secure into place. NOTE: Donot over tighten set screws.

MountedTrack

S T E P 1 Attach Hinge to VerandaAttach hinge to Veranda main frame with the track side facing outward. Secure together usingsupplied (1) hinge screw and (1) locknut. Note: Hinge screw only inserts one way. Tightenlocknut with supplied 6mm allen wrench.

Hinge

Main Frame

InsertHinge Screw

Lock Block

Set Screws

MountedTrack

MountedTrack

47

S T E P 1 Position TrackPosition track level on wall at desired height and location. Mark bolt holes on concrete ormain body of brick. If holes in track do not line up with existing structural supports, new holescan be drilled into the track to accommodate screw anchors.

S T E P 2 Drill HolesRemove track and drill 1/4” holes into wall about 3” deep and remove any loose concreteinside hole. Do not allow the holes to become tapered or oversized while drilling. Siliconecocking may be added to the holes before or after anchors are installed to prevent waterfrom penetrating wall.

S T E P 3 Install TrackUsing a 9/16” socket, install the track with the (4) 3/8” x 3 screw anchors and washers (notincluded). While tightening the screw anchors, keep the track level. Consult a licensedcontractor for bolts that fit these types of applications.

Brick

Correct

Incorrect

S T E P 4 Close VerandaRemove pin from hub. Pull on hub to unlock from center pole and guide hub down untilumbrella is fully closed. Tie canopy with supplied string to secure.

Mounting on masonry, brick or concrete walls:S T E P 3 Open VerandaGently pull ribs slightly outward, while grabbing hub. Push hub upward, through center poleuntil hub locks into place. Slide pin into hub for extra support.

MountedTrack

S T E P 5 Adjust PositionWhile in closed position, loosen hexagon set screws on hinge and adjust frame position bysliding hinge left or right on mounting track to desired location. To secure, tighten set screws.

MountedTrack

83

S T E P 4 Install TrackUsing a 9/16” socket, install the track with the four 3/8” x 3” lag bolts and washers (notincluded). While tightening the lag bolts, keep the track level. Do not overtighten the lag bolts;doing so may split the wood frame or weaken the lag bolt. Consult a licensed contractor forbolts that fit these types of applications.

Lag Bolt

Lag Bolt

Track

Shim

Siding

Shim

Stud

insi

de w

all

3/8” x 3”Lag Bolt

Lag Bolt

Track

Washer

Stud

insi

de w

all

3”

With ShimsWithout Shims

NOTE: For vinyl or aluminum sliding,shimming beneath the siding under thetrack may provide a more solid surfacefor mounting.

CAUTION: It is critical that you fasten two lag bolts at each end of the track to studs, headeror other major structural members in the wall. Consult a licensed contractor for bolts that fitthese types of applications.

WARNING: Failure to properly fasten mounting track to wall could result the umbrella tocollapse causing property damage and/or personal injury. We suggest consulting a licensedcontractor for proper mounting.

To Attach Umbrella Light: (sold separately)

Open the umbrella light by holding firmly with one hand and then depress the clamp releasebutton with the other hand to release the clamp lock. Open up the light and clasp aroundthe light adapter post. Snap to close. NOTE: It is not necessary to remove light to closeumbrella.

Features

S T E P 6 Protective Cover and Lock Block AssemblyInstall (2) protective cover lock blocks with (4) supplied tapping screws onto wall. Tiecanopy string around canopy to secure canopy. Slide protective cover over canopy usinginserted rod as a guide. Pull down on zipper pole to close protective cover. Secure with (2)protective cover handles to lock blocks installed on wall.

29

S A F E T Y P R E C A U T I O N S :• Close the umbrella in windy conditions or when a storm approaches. Never allow the umbrella to flap in the wind; this could damage the canopy.

• Properly store umbrella when not in use. Close umbrella, tie string around canopy andcover umbrella with provided protective cover.

• Do not leave open umbrella unattended. If damage occurs, this is not covered by the warranty.

• When adjusting the umbrella, make sure that no person(s) or item(s) are close to theumbrella. This is important to prevent injury or material damage.

C A R E A N D M A I N T E N A N C E :• When not in use, close and cover umbrella with a protective cover. • If necessary, clean the fabric with lukewarm water, mild detergent, and a sponge.• Allow a wet canopy to dry slightly opened, but do not leave unattended.• Wipe sliding marks on the aluminum poles with a damp cloth.

Winter Storage:• Store in a dry place.• Any visible defects must be repaired by a professional.

After the Winter:• Areas subject to turning and sliding can be treated with a non-staining lubricant spray(silicone-based).

• Check the condition and function of the umbrella. Any defects must be repaired by aprofessional.

S T E P 1 Locate StudsLocate studs in the area which the track will be installed.

S T E P 2 Position TrackPosition track level on wall at desired height and location. Allow ample height and width toavoid damage to your umbrella during assembly and operation. Place bolt holes at center ofstuds and mark. If holes in track do not line up with existing structural supports, new holescan be drilled into the track to accommodate lag bolts.

S T E P 3 Drill HolesRemove track and drill 1/4” holes into the wall about 3” into the studs. This will preventframe from splitting while installing the lag bolts. NOTE: Shims or spacers may need to beadded on angled sliding. Silicone cocking may be added to the holes before bolts areinstalled to prevent water from penetrating wall.

MOUNTING TRACK

Mounting on wood frame walls wood, vinyl, stucco or aluminum sliding, proceed below.

Mounting on masonry, brick or concrete walls, proceed to page 4.

Centerof Stud

Drill 1/4” Holes in 2 places on each side of track

Stud

Centerof Stud

StudWall

16” On Center

Mounting on wood frame walls with wood, vinyl, stucco or aluminumsliding:

Thank you for your purchase of Treasure Garden’s Veranda Wall Mount Umbrella.

Please remove all contents from the package, inspect and review checklist. CAUTION: To reduce personal injury and damage to your umbrella, read and follow thisassembly and operation guide. We recommend a two-person team for assembly anddisassembly. Save information for future reference. We suggest consulting a licensedcontractor for proper mounting.

101

A - 36” Mounting Track G - Lock Block with (2) Set Screws B - Screw Anchors and Washers (4) - 3/8” x 3” H - Protective Cover

(not included) I - Protective Cover Lock Blocks (2)C - Lag Bolts and Washers (4) - 3/8” x 3” J - Tapping Screws (4)

(not included) K - Allen Wrench - 4mmD - Veranda Umbrella L - Allen Wrench - 6mmE - HingeF - Hinge Screw and Locknut

CHECKLIST

WARRANTY:Treasure Garden warrants this product(in residential use) to be free fromdefects in original materials andworkmanship for a period of 2 year fromthe date of purchase. If a defect in theoriginal material or workmanshipappears during the warranty period;Treasure Garden will (at its option) repairor replace the product without charge.

Simply contact your original authorizedTreasure Garden dealer with adescription of the defect. The dealer willverify the defect and work closely withTreasure Garden to obtain the necessaryservice. In many cases, simple problemscan be solved with a replacement partthat can be shipped directly to the dealerfor professional installation / repair.

In the event that warranted factoryservice is required, Treasure Garden willassume the responsibility of the return

freight charges on warranted product forthe first year only.

Returned product that (upon receipt andinspection) is deemed to be “notcovered” under our warranty, will beshipped / billed at your expense.

This warranty gives you specific legalrights, and you may have other rightswhich vary from state to state.

RUST: Rust is a natural part of theaging process of steel or iron basedmaterials, and is therefore NOTconsidered a defect.

NOTE: Failure caused by unreasonableor abusive use, or failure caused byneglect of reasonable and necessarycare are not covered by this warranty.

Additionally, acts of nature (including butnot limited to wind, hurricanes,tornadoes, and storms) are not coveredby this warranty.

IMPORTANT:

Prior to assembly it is important to decide on the location of the umbrella.

• Allow ample height to avoid damage to your umbrella during assembly and usage.

Storage:

• Properly store umbrella when not in use. Close umbrella, tie string around canopy, coverumbrella with provided protective cover and tie cover handles to protective cover lockblocks. Or remove structure from mounting track and properly store structure.

NOTE: Some parts may be included in the styrofoam packaging. DO NOT discard any packaging or box until assembly is complete.

A -

B -

D -

C -

E -

F -

G -

I - J -

H -

K -

L -

VERANDA 5’x10’RT Wall Mount

Assembly and Operation Guide

www.treasuregarden.com

©2016 Treasure Garden, Inc. - All Rights Reserved. Rev. 10/16