Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
ASS
EM
BLY
IN
ST
RU
CT
ION
S
UTS MPO SeriesBT 319
3
Contents
Tool & Material .................................................... 4UTS MPO component details ............................. 5UTS MPO dimensions ......................................... 5Assembly instructions forUTS1JC18MPN & UTS6JC18MPN ..................... 6
A - Cable preparation ....................................... 6 B - Backshell screwing for UTS1JC18MPN ....... 9 C - Backshell screwing for UTS6JC18MPN ....... 10 Assembly instructions for UTS718MPN .............. 12
UTS MPO Series | BT319
4
OR OR
WITH
ReceptaclePlug
UTS MPO Series | BT319
The following tools and materials are necessary for preparation, assembly, inspection, and maintenance of the connector and cable assembly.Follow the tool instruction for operation and safety guidelines.
Tools• Cable jacket strip tool• Aramid Fiber Shears• Fiber Stripping Tool • 15 mm U–wrench• 28 mm U–wrench• 36.5 mm U–wrench• Nipper (Oeticker Standard)• Heat gun (optional)
Material• MPO contact: the UTS MPO connector range can adapt all kind of MPO contact as defined per IEC 61754-20• Cable: the UTS MPO connector range can adapt all type of standard cable from 3 to 6mm outer diameter. • Above these diameter limits some adaptations are necessary• Suggested glue: LOCTITE® 480 PRISM Instant Adhesive
Assembly instructionsThe assembly should be done in a dust free and dried environment, in accordance with fiber optics good practices. Make sure that all components are free from contamination.
The assembly instruction is only a guideline and the assembly/manipulations are under the responsibility of the assembler. Any change of product or material is under the responsibility of the assembler.
Tool & Material
Accessories
Sealing caps
Part number
UTS618DCG2
Part number
UTS18DCG2
For UTS1JC18MPN & UTS718MPNFor UTS6JC18MPN
Connector type BackshellPart number
Male insert Female insert
Free hanging receptacle Cable gland UTS1JC18MPN -Plug Cable gland - UTS6JC18MPN
Jam nut receptacle Without UTS718MPN -
Connector part numbers
5
UTS MPO Series | BT319
Dimensions
Free hanging receptacle - UTS1JC18MPN
Plug - UTS6JC18MPN
Ø 6
max
112 max
Ø 4
2.5
max
PlugBackshell
Tensile strength system
Ear
Claw Nut
Gasket
Crimp support
Receptacles
UTS1JC18MPN, UTS6JC18MPN, UTS718MPN overview
Sealing capØ
35.
7 m
ax
34 max
UTS18DCG2for UTS1JC18MPN & UTS718MPN
UTS618DCG2for UTS6JC18MPN
Jam nut receptacle - UTS718MPN 17.5 max 18.5 max
5 max
Ø 4
5.5
max
Ø 4
2.5
max
24 max
122 max
Ø 4
2.5
max
Ø 6
max
6
UTS1JC18MPN & UTS6JC18MPN
Cable preparation
1. Slide the backshell onto the cable allowing 50 cm at the end of the cable for stripping the cable. Make sure to orient each component as shown in the UTS MPO Component details section.
2. Using the cable jacket strip tool, strip the jacket to the dimension given in figure below, exposing the kevlar strength members and fiber.
4. Fix the Kevlar using an adhesive tape on the “individual fibers” to facilitate the insertion of the crimp support.
5. Slide the crimp support (large diameter end first) over the fibers and the kevlar strength members until it bottoms on the cable outer jacket.
3. Using the shears, trim the kevlar strength members to the length given in figure below.
Fiber tube protection: 100±1 mm
Kevlar: 40±1 mm
UTS MPO Series | BT319
Assembly instructions
7
UTS1JC18MPN & UTS6JC18MPN (Continued)
8. Before the instant adhesive begins to harden,quickly slide the ear clamp over the fiber, orient the Clamp according the picture.Push the strength members back over the clamp until it bottoms on the rear flange of the support.
6. Separate the kevlar strength members in two groups. Use an adhesive tape to fix the kevlar strength members on the jacket.
7. Apply the instant adhesive on the fiber and cover the crimp support. (e.g. Loctite 480 PRISM).
9. Crimp the both ear of the Clamp using the Nipper. Remove the kevlar strength members using using the shears.
Check the good crimping by pulling manually.
UTS MPO Series | BT319
8
UTS MPO Series | BT319
UTS1JC18MPN & UTS6JC18MPN (Continued)
Assembly instructions (Continued)
11. Terminate the MPO contact on the fiber according to your supplier instruction for gluing, cliving and polishing.
12. Fix the cable in a tool to avoid the rotation.
Free hanging receptacle UTS1JC18MPN
Free hanging receptacle UTS1JC18MPN: 94±1 mm
Plug UTS6JC18MPN: 85±1 mm
Plug UTS6JC18MPN
9
UTS MPO Series | BT319
UTS1JC18MPN & UTS6JC18MPN (Continued)
Backshell screwing for UTS1JC18MPN
13. Plug the MPO in the cavity.
You need to hear a “click”.
1. Slide the blackshell and screw it using a 28 mm U-wrench. Tightened the backshell with a 4 Nm torque.
2. Control: Pull on the cable to ensure that the retention system bottoms in the backshell.
3. Screw the head nut using a 15 mm U-wrench. Tightened the head nut with a 2 Nm torque.
10
1. You need a receptacle counter-part. Orient the polarization keys before you start mating the connectors.
2. Coupling plug with receptacle
3. Slide the blackshell and screw it using a 28 mm U-wrench. Tightened the backshell with a 4 Nm torque.
4. Control: Pull on the cable to ensure that the retention system bottoms in the backshell.
UTS MPO Series | BT319
Backshell screwing for UTS6JC18MPN
Assembly instructions (Continued)
11
Use the caps, UTS618DCG2 for plug or UTS18DCG2 for receptacle to protect the MPO contacts from surrouding contamination.
You need to hear a “click”.
5. Screw the head nut using a 15 mm U-wrench. Tightened the head nut with a 2 Nm torque.
UTS MPO Series | BT319
Backshell screwing for UTS6JC18MPN (Continued)
Recommendation
12
4. Seat o-ring, place receptacle in the panel cut-out.
O-ring
UTS718MPN
Jam nut
Panel thickness: 3.2mm max
30.3
5 m
m
31.85 mm
2. Terminate the MPO contact on the fiber according to your supplier instruction for gluing, cliving and polishing.
3. Plug the MPO in the receptacle.
You need to hear a “click”.
UTS MPO Series | BT319
Assembly instructions for UTS718MPN
Assembly instructions (Continued)
13
5. Tightened the jam nut with a torque of 5 Nm, using a 36.5 mm U- wrench.
6. Coupling.
UTS MPO Series | BT319
Assembly instructions for UTS718MPN (Continued)
WD
SUTS
MPO
BTU
SEN
01 ©
Cop
yrig
ht S
OU
RIA
U 2
019
- SO
URI
AU
is a
reg
iste
red
tra
dem
ark
All
info
rmat
ion
in t
his
doc
umen
t p
rese
nts
only
gen
eral
par
ticul
ars
and
sha
ll no
t fo
rm p
art
of a
ny c
ontr
act.
All
right
s re
serv
ed t
o SO
URI
AU
for
chan
ges
with
out
prio
r no
tifica
tion
or p
ublic
ann
ounc
emen
t. A
ny d
uplic
atio
n is
pro
hib
ited
, unl
ess
app
rove
d in
writ
ing
. Cre
dit
pho
tos
pag
e 11
© R
ido,
Goi
r, Se
py
/ Fo
tolia
[email protected] (Americas)
[email protected] (Europe - Asia - Africa)
Reliable People, Reliable Solutions