Atc100.Dwg. General

8 AB BOLT M6X20 304S.S. HHB W/WASHER & GASKET F BATTEN BAR (CLAMP BAR)

7

6

5

4

EXTRUDED EPDM GASKETS STAINLESS STEEL (1,4301) SEALING SCREWS ACCORDING TO ASTM D1418 WITH EPDM GASKET (WEATHER GUARD DOMED) EXCELLENCE GENERAL CLIMATE AND OZONE RESISTANCE

3 AB BOLT M6X20 304S.S. HHB W/WASHER & GASKET DOME SHEET/PANEL

2

1

STAINLESS STEEL (1,4301) SEALING SCREWS WITH EPDM GASKET (WEATHER GUARD DOMED) BATTEN BAR (CLAMP BAR) SECONDARY SEAL F

PRIMARY SEAL

DOME SHEET/PANEL E FLAME PROOF CONNECTION INTERLOCKING PANELS WITH METAL-TO-METAL CLAMPING ASSURES MAXIMUM PANEL STRENGHT. EXTRUSION BOLT CHANNEL DOME BEAM E

DOME BEAM

D

REINFORCEMENT TO PREVENT LOCAL BUCKLING OF THE PROFILE

AB BOLT EXTRUSION BOLT CHANNEL WEATHER GUARD DOMED WASHER

D

150,00

BOX BEAM-TYPE ALUMINIUM STRUT EXTRUSION WITH HIGH TORSIONAL STIFFNESS TO PREVENT TORSIONAL BUCKLING

EPDM GASKET BATTEN BAR (CLAMP BAR) SECONDARY SEAL

C DOME SHEET/PANEL CORROSION RESISTANT HIGH STRENGTH AlMgSi ALUMINIUM ALLOY FOR MAIN STRUT AND CLAMP BAR

PRIMARY SEAL

C

EXTRUSION BOLT CHANNEL

B

DOME BEAM

DOME BEAM

B DOME BEAM

BATTEN RIBBED DOME BEAM (TYPICAL)THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER

CHECKED APPROVED DATEDOCUMENT NO : REVISION NO

A

Geodesic DomeREV. DESCRIPTION REVISIONS NAME DATE

CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

ATC100.DWG.TYP.M.103

TYPICAL BEAM PROFILE CROSS-SECTION3 2

PURCHASE NO :

X

8

7

1

8

7 AB BOLT M6X20 304S.S. HHB W/WASHER & GASKET

6 STAINLESS STEEL (1,4301) SEALING SCREWS WITH EPDM GASKET (WEATHER GUARD DOMED)

5

4

3

2 AB BOLT

1

F

F

BATTEN BAR (CLAMP BAR)

EXTRUDED EPDM GASKETS ACCORDING TO ASTM D1418 EXCELLENCE GENERAL CLIMATE AND OZONE RESISTANCE EPDM GASKET FLAME PROOF CONNECTION

WEATHER GUARD DOMED WASHER

SECONDARY SEAL DOME SHEET/PANEL PRIMARY SEAL E

DOME SHEET/PANEL E INTERLOCKING PANELS WITH METAL-TO-METAL CLAMPING ASSURES MAXIMUM PANEL STRENGHT. DOME SHEET/PANEL


AB BOLT REINFORCEMENT TO PREVENT LOCAL BUCKING OF THE PROFILE D BEAM/STRUT AB BOLT EXTRUSION BOLT CHANNEL D

BOX BEAM-TYPE ALUMINIUM STRUT EXTRUSION WITH HIGH TORSIONAL STIFFNESS TO PREVENT TORSIONAL BUCKLING C

BOX BEAM-TYPE ALUMINIUM STRUT EXTRUSION WITH HIGH TORSIONAL STIFFNESS TO PREVENT TORSIONAL BUCKLING

EPDM GASKET

C WEATHER GUARD DOMED WASHER WEATHER GUARD DOMED WASHER

CORROSION RESISTANT HIGH STRENGTH AlMgSi ALUMINIUM ALLOY FOR MAIN STRUT AND CLAMP BAR


REINFORCEMENT TO PREVENT LOCAL BUCKING OF THE PROFILE

B

DOME BEAM DOME BEAM EPDM GASKET

B

THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

TYPICAL BEAM PROFILE AND BATTEN CONNECTION SECTION DETAIL3 2

ATC100.DWG.TYP.M.104PURCHASE NO :

X

8

7

1

8 AB BOLT M6X20 304S.S. HHB W/WASHER & GASKET F BATTEN BAR (CLAMP BAR)

7

6

5

4

3 AB BOLT

2

1

STAINLESS STEEL (1,4301) SEALING SCREWS WITH EPDM GASKET (WEATHER GUARD DOMED) EXTRUDED EPDM GASKETS ACCORDING TO ASTM D1418 EXCELLENCE GENERAL CLIMATE AND OZONE RESISTANCE

WEATHER GUARD DOMED WASHER BATTEN BAR (CLAMP BAR)

F

DOME SHEET/PANEL DOME PANEL FLAME PROOF CONNECTION PRIMARY SEAL SECONDARY SEAL EXTRUSION BOLT CHANNEL E INTERLOCKING PANELS WITH METAL-TO-METAL CLAMPING ASSURES MAXIMUM PANEL STRENGHT. AB BOLT E

WEATHER GUARD DOMED WASHER EPDM GASKET BATTEN RIB (TYPICAL)

D

BEAM / STRUT

REINFORCEMENT TO PREVENT LOCAL BUCKLING OF THE PROFILE

D

DOME SHEET/PANEL BOX BEAM-TYPE ALUMINIUM STRUT EXTRUSION WITH HIGH TORSIONAL STIFFNESS TO PREVENT TORSIONAL BUCKLING C CORROSION RESISTANT HIGH STRENGTH AlMgSi ALUMINIUM ALLOY FOR MAIN STRUT AND CLAMP BAR C

DOME BEAM DOME BEAM B B

TYPICAL BEAM & BATTEN CONNECTION

DOME BEAM

BATTEN RIBBED DOME BEAMS SECTIONTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4


TYPICAL BEAM AND BATTEN SECTION AND ISOMETRIC3 2

PURCHASE NO :

X

8

7

1

8 AB BOLT M6X20 304S.S. HHB W/WASHER & GASKET

7

6

5

4

3

2

1

F

STAINLESS STEEL (1,4301) SEALING SCREWS WITH EPDM GASKET (WEATHER GUARD DOMED)

BATTEN BAR (CLAMP BAR) DOME SHEET/PANEL

16 BOLT PATTERN 12 BOLT PATTERN 8 BOLT PATTERN 4 BOLT PATTERN

F

FLAME PROOF CONNECTION E E

INTERLOCKING PANELS WITH METAL-TO-METAL CLAMPING ASSURES MAXIMUM PANEL STRENGHT.


BATTEN SEAM DETAIL A

D TYPICAL INTERNAL/TENSION BEAM

TYPICAL BATTEN RIB

BATTEN RIB (TYPICAL)

D

DOME SHEET/PANEL BOX BEAM-TYPE ALUMINIUM STRUT EXTRUSION WITH HIGH TORSIONAL STIFFNESS TO PREVENT TORSIONAL BUCKLING REINFORCEMENT TO PREVENT LOCAL BUCKLING OF THE PROFILE

S1BATTEN SEAMS NOTES1 CORDS FOR MAXIMUM SEALING EFFICIENCY SILICONE SEAL CORDS TO MAXIMIZE LIFE UNDER ALL SERVICE CONDITIONS. 2 SOLID CORDS TO AVOID ANY ABSORPTION OF WATHER OR CHEMICALS.

S2

S3

S4

S5C

TYPICAL BATTEN RIBBED DOME BEAM DETAILSBATTEN RIBBED BEAMS GENERAL NOTES1 TENSION AND INTERNAL BEAM SIZES, WEIGHT, THICKNESS AND AREA WILL VERY ACCORDING TO THE INDIVIDUAL STRESS REQUIREMENTS. 2 FLANGE BOLT HOLE PATTERNS ARE DETERMINED BY SIZE AND LOADING CONDITIONS, REFERANCE STRESS SUMMARY SHEET FOR DETAILS. 3 TENSION BEAM WEB HOLES ARE REQUIRED ONLY WHEN A TENSION TIE STRAP IS CALLED FOR IN THE STRESS SUMMARY SHEET. THE NUMBER OF B TENSION TIE HOLES AND PATTERN WILL WARRY WITH LOADING CONDITIONS.

C


3 FULLY ENCLOSED SEAL CORDS, TO AVOID THE ENVIRON MENTAL HAZARDS OF EXPOZED ELASTOMERS. (CONDINOUS FULL LENGHT OF BATTEN BAR) 4 LOW PROFILE - INSTALLED BATTEN ONLY '' ABOVE SKIN PANEL.

B

5 METAL-TO-METAL GRIP-SERRATED CENTER RIBS OF BATTEN CLAMP SKIN PANEL EDGES TIGHLY AGAINST SERRATED BEAM FLANGE. RIBS ARE DIRECTLY BELOW FASTENER PROVIDING MAXIMUM PRESSURE. 6 ALL TEMPERATURE INSTALLATION - SPRING ACTION OF THE BATTEN ''WINGS'' INSURES UNIFORM PRESSURE AGAINST THE SEAL CORDS DURING COLD WEATHER INSTALLATION WHEN THE CORDS ARE ''FIRM''. THE SAME SPRING ACTION INSURES A TIGHT SEAL AS THE TEMPERATURE RISES AND THE SEAL CORDS SOFTEN.


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4 3

BATTEN BEAM & BATTEN RIBBED TYPICAL BEAM DETAILS2


X

8

7

1

8

7

6

5

4

3

2 DOME SHEET(PANEL (1,2mm)

1

F

SILICONE SEALANT AROUND EACH GUSSET COVER

CIRCULAR HUB COVER F HUB COVER CLIPS

HUB COVER CLIPS

SECTION B - BE AB BOLTS '' (M6) DIA x 25 mm LONGW/WASHER & GASKET (304S.S. HHB)

E

D SILICONE SEALANT BETWEEN GUSSET PLATE AND PANEL AT ENDS OF BATTEN BAR CIRCULAR FORMED TOP GUSSETS (NODE PLATE) 9,5mm DIA. AL. LOCK BOLTS, STRUT FLANGE TO GUSSET EACH END 4 TOP AND 4 BOTTOM

D

BC

B

SILICONE SEALANT BETWEEN HUB COVER AND PANEL CORNER

C BATTEN BAR (ALUMINIUM) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) GASKET BETWEEN HUB COVER TYPICAL GUSSET JOINT AND PANEL (SPECIAL) DOME SHEET/PANEL (1,2mm) CLOCED END SEALING RIVETS - (ALU) 4 DIA x 15 GRIP (TYP. 2 OF EACH PANEL 6 PLCS) ALL MATERIAL EXCEPT AS OTHERWISE NOTED IS MILL FINISH ALUMINIUM AS FOLLOWS; *STRUT/BEAM, GUSSETS AND PLATES: 6061-T6 *PANELS, FLASHING AND GUSSETS COVERS: 3003-H16 *BATTENS: 6061-T6

B

FASTENERS; LOCKBOLTS - ALU.7075-T3 OR S.S.304 AS NOTED (AL.LOCKBOLTS CLEAN ANOTIZED S.S.204) LOCKBOLTS COLLARS - ALUMINIUM (6061 HEAT TREATED) SHOE SUPPORT PLATE BOLTS - S.S.304 BATTEN SCREW - '' DIA. S.S.

ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) SEALANT; 3M, PECORA, DOW, HENKEL SILICONE SEALANT MEETING ATECO SPEC.

B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

HUB CONNECTION DETAILS SECTION3 2


X

8

7

1

8

7

6

5

4 CIRCULAR HUB COVER

3 SILICONE SEALANT AROUND EACH GUSSET COVER

2

1 CIRCULAR FORMED TOP GUSSETS (NODE PLATE) F

F

CIRCULAR HUB COVER

AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB)

B

SECTION A - AE DOME BEAM DOME SHEET/PANEL ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) HUB COVER CLIPS BATTEN BAR (ALUMINIUM) GASKET BETWEEN HUB COVER TYPICAL GUSSET JOINT AND PANEL (SPECIAL) E

DETAIL - B

CIRCULAR HUB COVER

AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) D

BATTEN BAR (ALUMINIUM) DOME SHEET/PANEL

DETAIL - C

D

AC

A

C

ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL)

C

DOME SHEET/PANEL

B CLOCED END SEALING RIVETS - (ALU) 4 DIA x 15 GRIP (TYP. 2 OF EACH PANEL 6 PLCS)

B

CIRCULAR HUB COVER

D DETAIL - D

HUB COVER CLIPS


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

HUB CONNECTION POSITION AND TYPICAL VIEW3 2


X

8

7

1

8

7

6

5

4

3 AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB)

2

1

F

GASKET BETWEEN HUB COVER TYPICAL GUSSET JOINT AND PANEL (SPECIAL)

HUB COVER CLIPS

CIRCULAR HUB COVER F DOME SHEET(PANEL (1,2mm) DOME SHEET(PANEL (1,2mm)

BATTEN BAR (ALUMINIUM) E E

CIRCULAR FORMED TOP GUSSETS (NODE PLATE)

D

ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) CIRCULAR FORMED TOP GUSSETS (NODE PLATE)

D

DETAIL - ACIRCULAR FORMED TOP GUSSETS (NODE PLATE) C

AC

CIRCULAR HUB COVER

AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) B ALL MATERIAL EXCEPT AS OTHERWISE NOTED IS MILL FINISH ALUMINIUM AS FOLLOWS; *STRUT/BEAM, GUSSETS AND PLATES: 6061-T6 *PANELS, FLASHING AND GUSSETS COVERS: 3003-H16 *BATTENS: 6061-T6 FASTENERS; LOCKBOLTS - ALU.7075-T3 OR S.S.304 AS NOTED (AL.LOCKBOLTS CLEAN ANOTIZED S.S.204) LOCKBOLTS COLLARS - ALUMINIUM (6061 HEAT TREATED) SHOE SUPPORT PLATE BOLTS - S.S.304 BATTEN SCREW - '' DIA. S.S. CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)

ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) CLOCED END SEALING RIVETS - (ALU) 4 DIA x 15 GRIP (TYP. 2 OF EACH PANEL 6 PLCS) B

CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)

SEALANT; 3M, PECORA, DOW, HENKEL SILICONE SEALANT MEETING ATECO SPEC.


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

HUB CONNECTION DETAIL ASSEMBLY EXPLODED3 2


X

8

7

1

8 SILICONE SEALANT AROUND EACH GUSSET COVER F

7 HUB COVER CLIPS

6 CIRCULAR HUB COVER

5

4

3

2

1

DOME SHEET(PANEL (1,2mm)

CIRCULAR HUB COVER


F

DALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL)

E

ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) CIRCULAR FORMED TOP GUSSETS (NODE PLATE) AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) CIRCULAR HUB COVER DOME SHEET(PANEL (1,2mm)

E

D CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) C BATTEN BAR (ALUMINIUM) GASKET BETWEEN HUB COVER TYPICAL GUSSET JOINT AND PANEL (SPECIAL) ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) CIRCULAR FORMED TOP GUSSETS (NODE PLATE) HUB COVER CLIPS

D

C

DETAIL - DBATTEN BAR (ALUMINIUM)

B

B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

HUB CONNECTION SECTION AND GASKET DETAIL AND COVER DETAIL3 2


X

8

7

1

8 DOME STRUCTURE F SLIDING SUPPORT

7

6

5

4

3

2

1

FIXED SUPPORT F

BATTEN BAR (ALUMINIUM) STEEL TENSION / COMPRESSION RING STEEL TENSION /COMPRESSION RING E E

BIRD SCREEN D RAIN FORCING TANK SHELL D

C

C

TANK SHEEL B BIRD SCREEN DOME SHEET/PANEL B

BIRD SCREEN DETAILTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


FIXED SUPPORT - FREE VENTED2


X

8

7

1

8

7

6

5

4

3

2

1

DOME STRUCTURE F DOME STRUCTURE STEEL TENSION / COMPRESSION RING SUPPORT BAR HEX SOCKET BOLTS FIXED SUPPORT BOLT

DOME STRUCTURE F HEX SOCKET BOLT

SUPPORT BAR E STEEL TENSION / COMPRESSION RING DOME STRUCTURE E

BOLTS D SAFETY PIN FIXED SUPPORT BOLTS D

FIXED SUPPORT

BOLT

C

FIXED SUPPORT SUPPORT BAR

C

SAFETY PIN NUTS STEEL TENSION / COMPRESSION RING

STEEL TENSION / COMPRESSION RING B NUTS B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0


FIXED SUPPORT DETAIL2


X

8

7

1

8 ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL)

7

6

5 DOME STRUCTURE

4

3 DOME STRUCTURE FIXED SUPPORT

2

1 BATTEN BAR (ALUMINIUM) F

DOME SHEET/PANEL BOLT BATTEN BAR (ALUMINIUM) STEEL TENSION / COMPRESSION RING

F

E CIRCULAR FORMED TOP GUSSETS (NODE PLATE) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) FIXED SUPPORT D BOLT SAFETY PIN STEEL TENSION / COMPRESSION RING

M8 HEX SOCKET BOLT BIRD SCREEN BATTEN BAR STEEL TENSION / COMPRESSION RING ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) TANK SHELL

E

D

DOME SHEET

C

CIRCULAR FORMED TOP GUSSETS (NODE PLATE) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) FIXED SUPPORT STEEL TENSION / COMPRESSION RING

DOME STRUCTURE C BATTEN BAR

B

TANK SHELL

B

BIRD SCREEN

DOME SHEET/PANEL


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

FIXED SUPPORT DETAIL ASSEMBLY3 2


X

8

7

1

8

7

6

5

4

3 DOME STRUCTURE

2

1

F DOME STRUCTURE

STEEL TENSION / COMPRESSION RING

AFIXED SUPPORT SUPPORT BAR

F

A

E

STEEL TENSION / COMPRESSION RING FIXED SUPPORT DOME SHEET BATTEN BAR

E STEEL TENSION / COMPRESSION RING

AD SUPPORT BAR TANK SHELL


D

DOME SHEET C SEAL TANK SHELL C

B


B

DETAIL - ASECTION A - ATHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

FIXED SUPPORT - PRESSURE TIGHT3 2


X

8

7

1

8 DOME STRUCTURE F SLIDING SUPPORT

7

6

5

4

3

2

1

SLIDING SUPPORT F GUIDANCE BATTEN BAR (ALUMINIUM)

LOW FRICTION PADS

STEEL TENSION /COMPRESSION RING E E

BIRD SCREEN D RAIN FORCING TANK SHELL D

C

C

TANK SHEEL B BIRD SCREEN DOME SHEET/PANEL B

BIRD SCREEN DETAILTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


SLIDIN SUPPORT - FREE VENTED2


X

8

7

1

8

7

6

5

4

3

2

1

F

DOME STRUCTURE

M8 BOLT DOME STRUCTURE

F

SLIDING SUPPORT

GUIDANCE E BOLT

SLIDING SUPPORT E

SUPPORT BAR SUPPORT BAR SAFETY PINS CLAMP

BOLTS SPACER PLATE CLAMP D CLAMP SAFETY PINS D

LOW FRICTION PADS SLIDING SUPPORT SPACER PLATE C LOW FRICTION PADS

C

SPACER PLATE LOW FRICTION PADS

SPACER PLATE B

NUTS B STEEL TENSION / COMPRESSION RING



PROJECT OWNER


A


CLIENTDESCIPTION :

A0


SLIDING SUPPORT DETAIL2


X

8

7

1

8

7

6

5

4

3 DOME STRUCTURE

2

1 BATTEN BAR (ALUMINIUM)

F


SLIDING SUPPORT DOME SHEET/PANEL BATTEN BAR (ALUMINIUM)

SLIDING SUPPORT LOW FRICTION PADS GUIDANCE STEEL TENSION /COMPRESSION RING

F

E CIRCULAR FORMED TOP GUSSETS (NODE PLATE) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) HEX SOCKET BOLT CLAMPING BAR M8 HEX SOCKET BOLT LOW FRICTION PADS RAIN FORCING BIRD SCREEN

E

D

SPACER PLATE STEEL TENSION / COMPRESSION RING

D

CIRCULAR FORMED TOP GUSSETS (NODE PLATE) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) C BOLT CLAMPING BAR SPACER PLATE TANK SHELL STEEL TENSION / COMPRESSION RING B SUPPORT BAR SLIDING SUPPORT LOW FRICTION PADSTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

TANK SHEEL

C

B BIRD SCREEN DOME SHEET/PANEL

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

SLIDING SUPPORT DETAIL ASSEMBLY3 2


X

8

7

1

8 DOME STRUCTURE F

7

6

5

4

3 DOME STRUCTURE

2

1 SLIDING SUPPORT F SUPPORT BAR LOW FRICTION PADS

CLAMP STEEL TENSION / COMPRESSION RING CLAMP POLYGONAL STEEL RING SPACER PLATE BOLT

SLIDING SUPPORT STEEL TENSION / COMPRESSION RING DOME SHEET STEEL TENSION / COMPRESSION RING SLIDING SUPPORT GUIDANCE SPACER PLATE STEEL TENSION / COMPRESSION RING FLEXIBLE SEAL D POLYGONAL STEEL RING TANK SHELL BOLT STEEL TENSION / COMPRESSION RING SEAL BATTEN BAR CLAMP DOME SHEET D

E

SPACER PLATE

FLEXIBLE SEAL

E

A

DETAIL - A - ISOMETRIC

C TANK SHELL

C

B WELD POLYGONAL STEEL RING FLEXIBLE SEAL

B

DETAIL - A


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

SLIDING SUPPORT - PRESSURE TIGHT3 2


X

8

7

1

8

7

6

5 ALUMINIUM HOOD (2mm)

4 ITEM 1 2 3 4 5 6 7342

3 QTY 1 1 1 1 20 20 20

2 PARTS LIST PART NUMBER

1 DESCRIPTION F

COVER DISK F

HOOD BLIND FLANGE, PIPE FLANGE M8x20 WASHER m8 nut

225

ALUMINIUM HOOD (2mm)

E

117

FLANGE ALUMINIUM

SLOTTED MESH %50 OPEN AREA

E

607 660 710

A

SLOTTED MESH %50 OPEN AREA 4 FLANGE ALUMINIUM

BOLD&NUT D

5

9 COVER DISK5

D

DETAIL-AModel Size 16 18 20 24 30 36 42 48 Model Size 16 18 20 24 30 36 42 48 Throat Area m 0,134 0,17 0,209 0,301 0,467 0,677 0,907 1,191 Throat Area m 0,134 0,17 0,209 0,301 0,467 0,677 0,907 1,191 0,1 1393 1691 2073 3024 4180 5080 7136 10024 Relief Performance Capacities (m/h) Total Pressure Drop in mbar 0,149 0,199 0,249 0,311 0,465 1741 2022 2277 2574 3135 2107 2447 2769 3118 3814 2582 3033 3390 3797 4638 3763 4383 4961 5530 6779 4910 5539 6142 6821 8359 6490 7671 8622 9633 11876 9175 10738 11944 13286 16497 12743 14951 16735 18774 23361 Intake Performance Capacities (m/h) Total Pressure Drop in mbar 0,199 0,249 0,311 0,465 1799 2005 2210 2757 2185 2436 2684 3350 2659 2965 3267 4076 3602 4108 4625 5658 4383 5556 6252 7595 7012 8052 9056 11001 9390 10784 12127 14732 12338 14168 15933 19357 0,622 3670 4443 5379 7900 9625 13830 19454 26589

FLANGE ALUMINIUM

C

0,746 4052 4944 5969 8733 10571 15299 21832 28798

0,871 4434 5418 6556 9599 11516 16684 24143 30922

C

B

ALUMINIUM HOOD FLANGE ALUMINIUM

0,1 1276 1551 1888 2447 3007 4361 5839 7673

0,149 1572 1910 2324 3092 4010 5811 7781 10223PROJECT OWNER

0,622 3143 3819 4647 6517 8716 12624 16905 22211CHECKED

0,746 3451 4193 5102 7195 9385 13602 18217 23934

0,871 3714 4513 5491 7781 9888 14333 19195 25220

B


APPROVED DATEDOCUMENT NO : REVISION NO

A


CLIENTDESCIPTION :

A0


CENTER / FREE VENT DETAIL2

ATC.100.DWG.TYP.M.119PURCHASE NO :

X

8

7

1

8

7

6

5 ALUMINIUM HOOD

4 ITEM 1 2 3 4 5 6 7 8 9 10 QTY 1 1 1 19 18 1 1 1 1 17

F

BIRD SCREEN (MESH) SLOTTED

2 PARTS LIST PART NUMBER 24 RECTANGULAR NOZZLE 24'' CENTER FREE VENT ASSEMBLY M8x20 m8 nut WASHER RECTANGULAR GASKET L.40x40x4-L L.40x40x4-R L.40x40x4-L_MIR M8x35 ALUMINIUM HOOD

3

1 DESCRIPTION F

E200mm (Ref.)

BS.S. BOLTED DOME PANEL DOME PANEL

E

D 100

A610 810 BIRD SCREEN (MESH) BOLD&NUT FLANGE ALUMINIUM 100 BACKUP PLATE

D

C

C

ALUMINIUM HOOD

B

SLICONE COULK ALUMINIUM ANGLE

DOME PANEL M8 S.S. WASHER B BOLD&NUT M8x25 HX.HD.S.S BOLD

DETAIL-A

DETAIL-B

ALUMINIUM ANGLE SILICONE SEALANT BETWEEN CURB&PANELBEFORE FASTENING VENT CURB TO PANEL RUN A CONTINUOUS BEED OF SILICONE SEALANT AROUND OUTSIDE PERIMETER OF HOLE PATTERN BETWEEN CURP AND PANELTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

CUT PANEL OPENING 25mm FROM MATCH-DRILLED HOLES AS SHOWN

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


CENTER / FREE VENT ASSEMBLY2


X

8

7

1

8

7

6

5 ALUMINIUM HOOD (2mm)

4

3

2

1

F225

F

FLANGE (ALUMINIUM)

E

117


342

E

A

C660 710 5 SLOTTED MESH %50 OPEN AREA

ALUMINIUM HOOD (2mm) FLANGE ALUMINIUM D COVER DISK SLOTTED MESH %50 OPEN AREA

D

WELDING DETAILBOLD

DETAIL-A0,622 3670 4443 5379 7900 9625 13830 19454 26589 0,746 4052 4944 5969 8733 10571 15299 21832 28798 0,871 4434 5418 6556 9599 11516 16684 24143 30922

BOLD C


Model Size 16 18 20 24 30 36 42 48 Model Size 16 18 20 24 30 36 42 48

Throat Area m 0,134 0,17 0,209 0,301 0,467 0,677 0,907 1,191 Throat Area m 0,134 0,17 0,209 0,301 0,467 0,677 0,907 1,191

0,1 1393 1691 2073 3024 4180 5080 7136 10024

Relief Performance Capacities (m/h) Total Pressure Drop in mbar 0,149 0,199 0,249 0,311 0,465 1741 2022 2277 2574 3135 2107 2447 2769 3118 3814 2582 3033 3390 3797 4638 3763 4383 4961 5530 6779 4910 5539 6142 6821 8359 6490 7671 8622 9633 11876 9175 10738 11944 13286 16497 12743 14951 16735 18774 23361 Intake Performance Capacities (m/h) Total Pressure Drop in mbar 0,199 0,249 0,311 0,465 1799 2005 2210 2757 2185 2436 2684 3350 2659 2965 3267 4076 3602 4108 4625 5658 4383 5556 6252 7595 7012 8052 9056 11001 9390 10784 12127 14732 12338 14168 15933 19357

C

B FLANGE ALUMINIUM

0,1 1276 1551 1888 2447 3007 4361 5839 7673

0,149 1572 1910 2324 3092 4010 5811 7781 10223PROJECT OWNER

0,622 3143 3819 4647 6517 8716 12624 16905 22211CHECKED

0,746 3451 4193 5102 7195 9385 13602 18217 23934

0,871 3714 4513 5491 7781 9888 14333 19195 25220

B


APPROVED DATEDOCUMENT NO : REVISION NO

A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

CENTER / FREE VENT INSTALLATION DETAIL3 2


X

8

7

1

8

7 CIRCULAR FORMED TOP GUSSETS (NODE PLATE)

6 ALUMINIUM FRAME COVER

5

4 ALUMINIUM FRAME COVER

3 SERIES S.S.304 SCREW/BOLT

2 8mm. TRIANGULAR CLEAR ACRYLIC LIGHTING PANEL (SKYLIGHT)

1

F


F

110

M8X25 BOLT CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL)

E DOME PANEL DOME GUSSETS DOME BEAM

102

SECTION A - ADOME GUSSETS DOME PANELS/SHEETS AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) SKYLIGHT

E

DOME SHEET/PANEL

AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) DOME GUSSETS

D BATTEN BAR (ALUMINIUM)

D

ALUMINIUM BOX PROFILE

BC DOME GUSSETS

M8X25 BOLT M8X25 BOLT BATTEN CLAMP BAR C

BA

A

8mm. TRIANGULAR CLEAR ACRYLIC LIGHTING PANEL (SKYLIGHT)

FOAM TYPE ALUMINIUM BOX PROFILE B B

CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)

DOME GUSSETS

SECTION B - BTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


TRIANGULAR SKYLIGHT DETAIL2


X

8

7

1

8 8mm. TRIANGULAR CLEAR ACRYLIC LIGHTING PANEL (SKYLIGHT) F ALUMINIUM BOX PROFILE

7

6 SERIES S.S.304 SCREW/BOLT ALUMINIUM FRAME COVER FOAM TYPE

5

4 SILICONE SEALANT CONTINUOUS SEAL ALL AROUND PERIMETER

3 8mm. TRIANGULAR CLEAR ACRYLIC LIGHTING PANEL (SKYLIGHT)

2

1

F

SECTION B-B110

CONDENSATE GUTTER WITH DRAIN HOLES102

E

SERIES S.S.304 SCREW/BOLT DOME BATTEN

8,00

DOME PANEL/SHEET

E M8 X 25 BOLT 6061-T6 ALUMINIUM SUPPORT BEAM

SEAL DOME SHEET/PANEL

BACKING BAR (ALUMINIUM) D DOME GUSSETS 40X40X2 L PROFILE BACKING (ALUMINIUM) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) C DOME BEAM/STRUT BATTEN CLAMP BAR AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) SKYLIGHT D

B

B

C

SKYLIGHT SPECIFICATIONB

A

DOME GUSSETS

A

SECTION A - A

1.) SKYLIGHT PANEL 8mm Thk. CLEAR ACRYLIC 2.) FRAME & SUPPORT - MILL FINISH ALUMINIUM 3.) SKYLIGHT AREA - APPROXIMATELY 2m EACH 4.) TOTAL SKYLIGHT AREA - MIN 1m/100m PROJECT AREA

B CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)


PROJECT OWNER


A


CLIENTDESCIPTION :

A0


TRIANGULAR SKYLIGHT DETAIL2


X

8

7

1

8 246 F

7 747 342

6 160

5 490 245 245

4

3 ITEM 1 2 3 4 5 6 7328

2 QTY 1 1 1 1 2 2 2 PARTS LIST PART NUMBER BODY UPPER FLANGE LOVER FLANGE SEAT (VACUUM) SEAT (PRESSURE) BEARING CAP DIAPHRAGM

1 DESCRIPTION ALUMINIUM ALUMINIUM ALUMINIUM ALUMINIUM ALUMINIUM ALUMINIUM ALUMINIUM

F

328

7

E703 703

E 5

175

175

1 4 3200 200

1

DETAIL-A

DETAIL-B2 D

D 6

6''150#

342

C

C

490

5 7 B 246 753 342 165 1 3 4 B

PRESSURE VACUUM VENT SECTION VIEWTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

PRESSURE VACUUM VENT DETAILS TYPICAL3 2


X

8

7

1

8

7

6 NUT

5 PIPE

4 NUT GASKET DOME PANEL

3 ITEM 1 2 3 4 5 6 QTY 3 3 3 1 3 1

2 PARTS LIST PART NUMBER NODE PLATE TOP NODE PLATE LOW DOME BEAM DOME SHEET/PANEL BATTEN BAR PRESSURE VACUUM VENT

1 DESCRIPTION ALUMINIUM ALUMINIUM ALUMINIUM ALUMINIUM ALUMINIUM -

WASHER

F

F

PRESSURE VACUUM VENT

WASHER BRACE ANGLE E BRACE ANGLE BOLD BOLT PRESSURE VACUUM VENT E

DETAIL-BBOLT&NUT DOME PANEL D 6'' PIPE GASKET

DETAIL-C

D

DOME PANEL

B168.3 C

DOME PANEL BRACE ANGLE

DETAIL-DBRACE ANGLE PIPE C

BOLT&NUT

GASKET BOLT&NUT

PIPE BOLT&NUT

B BRACE ANGLE 160 BRACE ANGLE BRACE ANGLE 40

B

DETAIL-A

40

250

DETAIL-ETHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4


PRESSURE / VACUUM VENT ASSEMBLY TYPICAL3 2

PURCHASE NO :

X

8

7

1

8

7

6

5

4 COVER

3

2

1

COVER F CAMLOCK 6 3

ARM

ARM

F FLANGE BODY 3 ARM DIAPHRAGM

DETAIL - A2 E 5 8 COVER/DIAPHRAGM 6 CAMLOCK E

1

FLANGE BODY D COVER/DIAPHRAGM D

A4 CAMLOCK FLANGE BODY 3 CAMLOCK 6 1 5 2

8

DIAPHRAGM

FLANGE BODY C C

2 PARTS LIST ITEM QTY PART NUMBER 1 1 Flange Body 2 1 Cover 3 1 Arm 4 1 Diaphragm 5 1 Camlock Stud Bolt 6 1 Camlock 7 2 M10 Nut 8 1 M10x50 DESCRIPTION Aluminium Aluminium Aluminium Teflon Stainless Steel Aluminium Stainless Steel Stainless Steel

ARM B

B

8

1


PROJECT OWNER


A


CLIENTDESCIPTION :

A0


GAUGE HATCH DETAILS TYPICAL2


X

8

7

1

8

7

6

5 NUT

4

3 NUT WASHER GASKET

2 FLANGE

1

GAUGE HATCH F

WASHER F

GASKET DOME PANEL BOLD&NUT

DOME SHEET

BACKING FRAME (ALUMINIUM)

M8 BOLT E BRACE ANGLE

BRACE ANGLE E

DETAIL - A - EXPLODEDBOLT

DETAIL - A - EXPLODED6'' PIPE BRACE ANGLE DOME PANEL D BATTEN BAR (ALUMINIUM) DOME SHEET/PANEL

CIRCULAR FORMED TOP GUSSETS (NODE PLATE) GAUGE HATCH

D

DETAIL - A - ISOMETRICDOME PANEL

C

A168.3 BOLD&NUT BOLD&NUT

BRACE ANGLE

C PIPE

B DOME PANEL BRACE ANGLE BRACE ANGLE 40 168.3 250 40 CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

B

DETAIL-A

DETAIL-E

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

GAUGE HATCH ASSEMBLY TYPICAL3 2


X

8

7

1

8 MANWAY COVER F

7

6 MANWAY HANDLE

5

4

3 ITEM 1 2 3 4 5 6 7 QTY 3 3 3 1 33 33 3

2 PARTS LIST PART NUMBER GUSSET PLATE TOP GUSSET PLATE LOW DOME BEAM DOME SHEET/PANEL WASHER M8 BOLT CLAMP

1 DESCRIPTION F

HEX NUT M8 WASHER (A8.4) MANWAY FRAME

ADOME SHEET/PANEL E MANWAY FRAME

MANWAY FRAME MANWAY FRAME

GASKET BRACE ANGLE DOME SHEET/PANEL BACKING FRAME (ALUMINIUM) E M8 BOLT

GASKET DOME SHEET DOME SHEET /PANEL D BRACE ANGLE

BRACE ANGLE

DETAIL - A - EXPLODED DETAIL - A - ISOMETRIC DETAIL - ACIRCULAR FORMED TOP GUSSETS (NODE PLATE) MANWAY LIT BATTEN BAR (ALUMINIUM) MANWAY LIT (OPENS 180) D BATTEN BAR (ALUMINIUM) MANWAY LATCH (LOCKAD)

MANWAY HANDLE

C

C

DOME SHEET DOME SHEET/PANEL MANWAY FRAME B MANWAY FRAME MANWAY HANDLE CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0


MANHOLE / HATCH COVER2


X

8

7

1

8

7

6

5

4

3

2

1

110,00

F

MANWAY LIT

GASKET DOME SHEET MANWAY LATCH (LOCKAD)

F

873,00

BRACE ANGLE BACKING FRAME (ALUMINIUM) BODY

BODY

E

DETAIL - A

E

814,00

DOME SHEET/PANEL

ACIRCULAR FORMED TOP GUSSETS (NODE PLATE)

CIRCULAR FORMED TOP GUSSETS (NODE PLATE) D MANWAY LIT MANWAY HANDLE

D DOME SHEET/PANEL

MANWAY FRAME MANWAY FRAME

MANWAY HANDLE

C CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)

C

BODY

B

CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) DOME SHEET/PANEL

B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

MANHOLE / HATCH COVER (ELEVATED)3 2


X

8

7

1

8 6'' PIPE F

7

6 NUT

5

4PIPE (BY OTHERS)

3Code DD101 Pipe Boot #1 Pipe Boot #2 Pipe Boot #3 Pipe Boot #4 Pipe Boot #5 Pipe Boot #6 Pipe Boot #7 Pipe Boot #8 Pipe Boot #9 5-65 45-80 5-127 73-160 108-190 125-230 150-280 175-330 254-483

2Description Pipe Size Metric Pipe Size Imperial 1/4"- 2 1/2" 1 3/4"-3 1/4" 1/4"-5" 3"-6 1/4" 4 1/4"-7 1/2" 5"-9" 6"-11" 7"-13" 10"-19" Base mm 137x137 177x177 218x218 284x284 365x365 365x365 453x453 453x453 685x685 Inch 39" 64" 69 1/2" 85 3/4" 111 3/4" 143 1/2" 178 1/2" 178 1/2" 269 3/4"

1Material EPDM EPDM EPDM EPDM EPDM EPDM EPDM EPDM EPDM

RETROFIT PIPE FLASHING (EPDM) RIVITED TO DOME PANEL

DD102 DD103 DD104

F

FLANGE DOME PANELSILICON SEAL ALL AROUND

RUBBER

DD105 DD106 DD107

BOLD (M6)

DETAIL-DE FLANGEPIPE (BY OTHERS)

DD108 DD109

E

EPDM WILL WITHSTAND CONSTANT TEMPERARURES AT THE ROOFLINE -50C (122F) TO 115C (239F) & UP TO 150C (302F) INTERMITTENTLYDOME PANEL

NUT RUBBER WASHER

BRUBBER D 6'' PIPE 168,3 (6'' PIPE) DOME PANEL FLANGE

F

D

PIPE BOOT SECTION

BRACE ANGLE BOLD&NUT

DETAIL-CBOLD C 168,3 30 305 365 RUBBER FLANGE B 30

DOME PANEL PIPE BOOT PIPE C

DETAIL-EEASILY CUSTOMIZED PIPE OPENING NINE DIFFERENT SIZE FIT PIPES (1/4''-19'') TOUGH ULTRAVIOLET RESISTANT ''EPDM'' RUBBER CARRIES THE BEST GUARANTEE IN THE INDUSTRY SQUARE FLANGE DESIGN ADAPTS TO ANY ROOFING MATERIAL SEALS TIGHTLY WITH SILICONE SEALANT AND STANDARD ROOFING FASTERNERS

DETAIL-B

ALUMINIUM BASE BENDS TO FORM A PERFECT SEAL WITH ANY CONTOUR SURFACE IRREGULARITIES OR ROOF PITCH

B

BOLD&NUT BRACE ANGLE FLANGE

DETAIL-A

RUBBER SECTION VIEWTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

DETAIL-FPROJECT OWNER CHECKED APPROVED DATEDOCUMENT NO : REVISION NO

A


CLIENTDESCIPTION :

A0


PIPE BOOT DETAIL2


X

8

7

1

8

7

6

5

4

3

2

1

F


DOOR COVER


HANDLE F COVER DOOR WELL

CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) E


DOME SHEET/PANEL

M8 x 25 BOLT SEAL E BACKING BAR (ALUMINIUM)

SECTION A-ADOME GUSSETS

DOME SHEET(PANEL (1,2mm) AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) DOME GUSSETS


DOME SHEET(PANEL (1,2mm) D

D

C

C

DOME GUSSETS

A

ACIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) DOME GUSSETS

B

BATTEN CLAMP BAR DOME GUSSETS CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

B

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


DOOR SECTION TYPICAL2


X

8

7

1

8

7

6

5

4

3

2 FLANGE

1

F79 n2 ,4 0

5

FLANGE

F

PIPE

PIPE WELDING

WELDING

REINFORCING PAD

DETAIL-G

FLANGE

E

E

FLANGE

279,4 D 241,310

D

PIPE

FLANGE

22

G

WELDING NOZZLE PAD

NOZZLE PAD C PIPE500

C NOZZLE PAD

DOME SURFACE

DETAIL-E

34,6 2

DOME SURFACE B BOLD&NUT

B

E168.3

GASKET

D

DETAIL-DTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


6'' TYPICAL NOZZLE2


X

8

7

1

8n

7290 2 ,9

6

5

4

3 FLANGE

2

1

8,4

F

5

34 n

F FLANGE

PIPE

AE

AE

FLANGE

REINFORCING PAD

FLANGE

342,90 298,45

WELDING

C22,3 D NOZZLE PAD D

WELDING5,00

FLANGE

500,00

C

22,3 8'' PIPE 8'' PIPE

10,00

8'' PIPE WELDING NOZZLE PAD

C

DETAIL - C B

GASKET

DOME SURFACE B BOLTS & NUTS 219,10 B

SECTION A - A

DETAIL - BTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


8'' TYPICAL NOZZLE2


X

8

7

1

8n25

7 FLANGE

6

5

4

3

2

1

,40

F

n

36 1,9 5

06, n4

40

FLANGE

F

FLANGE 10'' PIPE

E

A

AWELDING NOZZLE PAD

E

10'' PIPE 406,40 361,95 D 25,4 FLANGE

D

CNOZZLE PAD WELDING FLANGE10,00 5,00

PIPE C500,00

25,40 C PIPE WELDING NOZZLE PAD GASKET

B

DETAIL - C

DOME SURFACE B BOLTS & NUTS B

DETAIL - BSECTION A - ATHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


10'' TYPICAL NOZZLE2


X

8

7

1

8n3

75,05

6

5

4 24'' FLANGE

3

2

1

F

n

FLANGE12 n8 ,8 0

74

9,3

F FLANGE 24'' PIPE

0

WELDING E E

A

A

NOZZLE PAD

WELDING D 24'' FLANGE 812,80 35,0512,00 6,00

24'' FLANGE NOZZLE PAD

D

749,30

C24'' PIPE

24'' PIPE 24'' PIPE C NOZZLE PAD GASKET

C600,00

DETAIL - C B

WELDING

24'' PIPE B

DOME SURFACE B BOLTS & NUTS

610,00

SECTION A - A

DETAIL - BTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


24'' TYPICAL NOZZLE2


X

8

7

1

8

7 S.S.304 M10 x 40 BOLT

6

5 SAFETY POLE COVER 1'' Thk. ROUND PLATE 6061-T6 ALUMINIUM (M10 SCREWED)

4

3

2

1

SAFETY POLE COVER 1'' Thk. ROUND PLATE 6061-T6 ALUMINIUM (M10 SCREWED)

S.S.304 M10 x 40 BOLT F

F 4'' x '' mm Thk PIPE (10'' LONG) 6061 ALUMINIUM 4'' x '' mm Thk PIPE (10'' LONG) 6061 ALUMINIUM

WELDED TO THE PLATE (INSIDE AND OUTSIDE)280,00

FIELD APPLY (*) SILICONE SEALANT CENTER HUB COVER FIELD APPLY (*) SILICONE SEALANT BATTEN HUB CLIPS UPPER NODE PLATE DOME PANEL E

E

CENTER HUB COVER

D BATTEN HUB CLIPS

D

LOW NODE PLATE

SILICONE SEALANT BETWEEN GUSSET PLATE AND PANEL AT ENDS OF BATTEN BAR M10x60 LG. HH W/NUTS (S.S.) LOCKED ON TO STANDART NODE PLATE

4'' DIA CENTER PIN DETAILC

M10x60 LG. HH W/NUTS (S.S.) LOCKED ON TO STANDART NODE PLATE WELDED TO THE PLATE (INSIDE AND OUTSIDE) C

B

1.) NODE PLATE SUPPLIED EITH 11 HOLE 2.) PAINTERS PIN IS DESIGNED TO SUPPORT A 5000 LB LOAD SUSPENDED OVER THE EDGE OF THE DOME 3.) SHIP PLATE ASSEMBLED WITH STUD, NUTS, & WASHERS SHOP INSTALLED TO INSURE. THE CORRECT LENGTH OF THREAD ENGAGEMENT (NO CAULK) AND TO INSURE THAT COVER PLATE IS IN PLACE DURING DOME ERECTION. * SILICONE SEALANT FIELD APPLIED TO THE HUB COVER FLANGE, THE TOP OF THE PIPE AND AROUND THE HOLE IN THE HUB COVER.

LOW NODE PLATE SILICONE SEALANT BETWEEN GUSSET PLATE AND PANEL AT ENDS OF BATTEN BAR

NOTE;EYEBOLT FOR DOME ACCESS MAINTENANCE ONLY BY QUALIFIED PERSONNEL. EYEBOLT RATED FOR OSHA FALL PROTECTION - MUST BE INSPECTED OUR REPLACED AFTER FALL OR OTHER SHOCK LOADING. REMOVE ANY TEMPORARY SAFETY LINE IMMEDIATELY AFTER USE.THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

B

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


CENTER SAFETY LINE SUPPORT2


X

8

7

1

8

7

6

5 DOME SHEET(PANEL (1,2mm)

4

3

2

1

'' S.S. EYEBOLT W/(2) NUTS & WASHERS (SEE NOTE)

CIRCULAR HUB COVER F

F

'' S.S. EYEBOLT W/(2) NUTS & WASHERS (SEE NOTE) SILICONE SEALANT AROUND EACH GUSSET COVER DOME APEX GUSSET

HUB COVER CLIPS E E

D

D

CIRCULAR FORMED TOP GUSSETS (NODE PLATE) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)

C

NOTE;EYEBOLT FOR DOME ACCESS MAINTENANCE ONLY BY QUALIFIED PERSONNEL. EYEBOLT RATED FOR OSHA FALL PROTECTION - MUST BE INSPECTED OUR REPLACED AFTER FALL OR OTHER SHOCK LOADING. REMOVE ANY TEMPORARY SAFETY LINE IMMEDIATELY AFTER USE.ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL)

C

SILICONE SEALANT BETWEEN GUSSET PLATE AND PANEL AT ENDS OF BATTEN BAR

B

B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0


S.S. EYEBOLT AT DOME APEX2


X

8

7

1

8

7

6

5

4

3

2

1

F

HUB COVER

F

DOME SHEET(PANEL (1,2mm) HUB COVER CLIPS TOP GUSSET

E BOTTOM GUSSET FIELD DRILL (11mm) DIA. HOLE & INSTAL '' x 2'' S.S. EYEBOLT TO BOTTOM GUSSET WITH (2)NUTS AND (1) WASHER CABLE CLAMP D

E

D

ANTI ROTATION CABLE (BY OTHERS) SILICONE SEALANT BETWEEN HUB COVER AND PANEL CORNER BATTEN BAR (ALUMINIUM) CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) CIRCULAR FORMED TOP GUSSETS (NODE PLATE)

C

C

NOTE:

LOCATE @ XX GUSSETS FOR TOTAL APPLIET LOAD = 38,7 kN LOAD @ EACH CONNECTION = 1,21 kNB ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL)

SILICONE SEALANT BETWEEN GUSSET PLATE AND PANEL AT ENDS OF BATTEN BAR

FIELD DRILL (11mm) DIA. HOLE & INSTAL '' x 2'' S.S. EYEBOLT TO BOTTOM GUSSET WITH (2)NUTS AND (1) WASHER

B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

EYEBOLT CONNECTION & INSTALLATION DETAIL FOR IFR CABLE3 2


X

8

7

1

8

7

6

5 S.S.316 TOP PLATE (by Others)

4

3

2

1

F


F S.S.316 TOP PLATE (by Others)

DOME SHEET/PANEL

E

BATTEN BAR (ALUMINIUM)

E


ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) S.S.316 TOP PLATE (by Others)

ALUMINIUM FLANGE ASSEMBLY (by ATECO) FOR FLAME DETECTOR (by Others)

D

BATTEN BAR (ALUMINIUM) DOME SHEET/PANEL CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE) BATTEN BAR (ALUMINIUM)

D

C ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) MATCH DRILL 10mm DIA HOLES & USE ALUMINIUM LOCK BOLTS AB BOLTS '' (M6) DIA x 25 mm LONG W/WASHER & GASKET (304S.S. HHB) B DOME SHEET/PANEL ALUMINIUM FLANGE ASSEMBLY (by ATECO) FOR FLAME DETECTOR (by Others)

C

B


PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

24'' FLAME DETECTOR FLANGE ASSEMBLY3 2


X

8

7

1

8

7

6

5

4

3

2

1

F

S.S. HATCH LID HOLDOWN EYE-BOLT

F

S.S. NUT & 1 '' WASHER

BATTEN BAR

E

E

SKIN PANEL/DOME SHEET

D

D

BATTEN BEAM

INSTALLATION PROCEDURE: 1 OPEN HATCH LID AND DETERMINE PROPER LOCATION FOR ''HATCH LID HOLDOWN.''

C

2 DRILL ONE '' HOLE DOWN THROUGH THE BATTEN BAR OR SKIN PANEL. SKIP TO STEP 4 FOR LAPPED DOMES. 3 APPLY A FEW DROPS OF MOTOR OIL ON THE THREAD OF A '' BOLT (#14 FASTENER) AND IMPACT BOLT INTO BEAM GROOVE. THE BOLT WILL FORM THREADS IN THE GROVE OF THE ALUMINIUM BEAM. 4 REMOVE THE '' BOLT AND APPLY A GENEROUS AMOUNT OF SILICONE CAULC AROUND THE '' BOLT HOLE. THIS WILL INSURE THAT THE WATHER -TIGHT INTERGRITY OF THE DOME IS MAINTAINED WHEN INSTALLING THE ''HATCH LID HOLDOWN.'' 5 SCREW THE S.S. EYEBOLT IN THE PRE-THREAD GROOVE UNTIL THE EYEBOLT BOTTOMS THE OUT AND LOCKS DOWN TIGHT W/ S.S. NUT AND WASHER.THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

C

B

B

BATTEN INSTALLATIONFOR ENCLOSED-SEAL BATTEN

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

HATCH LID HOLD-DOWN INSTALLATIONENCLOSED-SEAL BATTEN 3 2


X

8

7

1

8

7

6

5

4

3

2

1

F

S.S. HATCH LID HOLDOWN EYE-BOLT

F

S.S. NUT & 1 '' WASHER

BATTEN BAR

E

E

SKIN PANEL/DOME SHEET

D

D

BATTEN BEAM

INSTALLATION PROCEDURE: 1 OPEN HATCH LID AND DETERMINE PROPER LOCATION FOR ''HATCH LID HOLDOWN.''

C

2 DRILL ONE '' HOLE DOWN THROUGH THE BATTEN BAR OR SKIN PANEL. SKIP TO STEP 4 FOR LAPPED DOMES. 3 APPLY A FEW DROPS OF MOTOR OIL ON THE THREAD OF A '' BOLT (#14 FASTENER) AND IMPACT BOLT INTO BEAM GROOVE. THE BOLT WILL FORM THREADS IN THE GROVE OF THE ALUMINIUM BEAM. 4 REMOVE THE '' BOLT AND APPLY A GENEROUS AMOUNT OF SILICONE CAULC AROUND THE '' BOLT HOLE. THIS WILL INSURE THAT THE WATHER -TIGHT INTERGRITY OF THE DOME IS MAINTAINED WHEN INSTALLING THE ''HATCH LID HOLDOWN.'' 5 SCREW THE S.S. EYEBOLT IN THE PRE-THREAD GROOVE UNTIL THE EYEBOLT BOTTOMS THE OUT AND LOCKS DOWN TIGHT W/ S.S. NUT AND WASHER.THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

C

B

B

BATTEN INSTALLATIONFOR ENCLOSED-SEAL BATTEN

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

HATCH LID HOLD-DOWN INSTALLATIONENCLOSED-SEAL BATTEN 3 2


X

8

7

1

8 405 F ARM 3

7

6 HANDLE COVER 2

5 240

4 656 176 240

3 ITEM 1 3 6

2 QTY 1 1 20 PARTS LIST PART NUMBER BODY ARM BOLT

1 DESCRIPTION SS316 SS316 F SS316

OPENING PRESSURE: XX mbar105

En813

120

225

BODY

1

BODY 610n813

E

FRONT VIEW LEFT VIEW1 2 COVER 2

D 3 COVER ARM

D

813

C

C

3 B ARM

1 B

BODY

TOP VIEWTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


EMERGENCY VENT DETAIL TYPICAL2


X

8

7

1

8

7 778 600

6

5

4

3

2

1

ARM F

COVER

ARM

F

450

BODY BODY

E895 895 1028

583

E

220

CONE445

COVER BODY

225

D

PIPE

D

6'' FLANGE

168 ARM

636

230

B

176

230

C

C

B BODY

SECTION VIEWTHIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0

DOME-ROOF-SEAL6 5 4

GAUGE POLE BASIN DETAIL TYPICAL3 2


X

8

7

1

8

7

6

5

4

3

2

1

F

'' DIA. x 2 '' GRADE 8 OR A490 BOLT 1'' DIA. HOLE 2'' FROM END OF LIFTING LUG

F

ADOME BEAM/STRUT E


REINFORCED DISK ORIENT LIFTING LUGS TO ALIGN WITH LIFTING BRIDLES. (NOTE; THIGTNESS PRIOR TO LIFTING DOME.)

E

D REINFORCED DISK

D

DOUBLE NUT

C

REINFORCED DISK FOR NUT CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)

C

SECTION A-A

B


B

A


PROJECT OWNER


A


CLIENTDESCIPTION :

A0


LIFTING LUG INSTALLATION2


X

8

7

1

8

7

6

5

4

3

2

1

F

Measure outside pipe diameter and trim cone exactly where indicated. For square pipes add 30%.

Fasten flashing with washered self drilling screws. As per diagram, secure clip by placing a fastener either side of the clip first.

F

E

E

With clip in down-stream position, tension top of cone around pipe and engage metal teeth in opposing pockets.D

Apply sealant to top of crimp closure and any other potential leak areas. (refer to page 13 for silicone types).D

C

To assist in locating clip into pocket, place hand behind the seam. Fasten clip with pliers or multigrips, working from top to base. Do not overcrimp.

Code RF801G RF802G RF803G

Material Gray EPDM Gray EPDM Gray EPDM

Base-mm 160 273 369

Pipe-mm 20-70 50-185 85-255 C

B

Apply a liberal bead of neutral silicone sealant to the underside of Dektite base and press to contour of sheet profile.

B

EPDM withstands temperatures from -50C - 115C and up to 150C intermittently.


PROJECT OWNERA



CLIENTDESCIPTION :

A


DEKTITE RETROFIT ORIGINAL INSTALLATION INSTRUCTIONS2


0

X1

8

7

8

7

6

5

4

3

2

1

F

Cut Dektite cone where indicated for the relevant pipe size

F

E

E

Slide Dektite flashing down over pipe. Water can be used as a lubricant

D

D

Apply neutral cure silicone sealant on underside of flange

C

C

Press pipe flashing into contours of roof panelB

Fasten flashing to surface with self-tapping or self drilling screws; or selected pop rivets

B


PROJECT OWNERA



CLIENTDESCIPTION :

A

DOME-ROOF-SEAL6 5 4

DEKTITE INSTALLATION INSTRUCTIONS3 2


0

X1

8

7

8

7

6

5

4 6,4mm ('') SELF-TAPPING SCREWS

3

2

1

F

4,8mm (3/16'') S.S. WIRE ROPE BREAKING STRENGTH 1878kg (3700lb)

F ALUMINIUM HOUSING FOR CABLE STORAGE 4,8mm (3/16'') S.S. WIRE ROPE BREAKING STRENGTH 1878kg (3700lb)

COPPER STOP SLEEVES (NOMINAL PULL-OUT STRENGTH 488kg - (1075lb) EACH) PERMANENT WASHER E

E

S.S. ROPE CLIP

D

TOP GUSSET WITH 12,7mm ('') HOLE AT CENTER & 11,1mm (7/16'') HOLE FOR EYEBOLT HUB COVER CLIPS

D

ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) C 11,1mm (7/16'') HOLE FOR EYEBOLT 12,7mm (1/2'') HOLE AT CENTER (CHAMFER) 9,5mm x 38,1mm (3/8'' x 1 1/2'') S.S. EYEBOLT WITH S.S. WASHER AND (2) S.S. NUTS CIRCULAR FORMED BOTTOM GUSSETS (NODE PLATE)8

C

VERTICAL LINE FROM GUSSET TO IFR B

MAX. ANGLE FOR IFR ALUMINIUM DOME BEAM 150mm DEEP BEAM (TYPICAL) B

CIRCULAR FORMED TOP GUSSETS (NODE PLATE)THIS DRAWING IS THE PROPERTY OF AKTEK. IT IS NOT TO BE TRACED, COPIED OR PUBLISHED WITHOUT THEIR WRITTEN CONSENT OR TO BE MISUSED IN ANY WAY.

PROJECT OWNER


A


CLIENTDESCIPTION :

A0


IFR CABLE HOUSING ASSEMBLY2


X

8

7

1

Documents

Atc100.Dwg. General