INTRODUCTION Our jnique passive in`raroC ^ys,e^ii conccotrates on the protected area you select. Whenever the unit is set at ARMED, the motion detector will concentrate on the protected area. Once there is movement detected, the alarm will turn on and call to the memorized telephone numbers one by one. In siren mode, In chime mode, the chime will Ding Dong when movement be detected. .O. 1. Do not install the system where it will be exposed to direct sunlight or rain. 2. The system siren is very loud, never put the unit close to your ear. 3. The unit should be away from heat sources such as radiators, heating ducts and stoves. 4. If the system sounds at random, it is possible that the location too close to a heat source, changing the location or direction of the unit can remedy this. 5. The system can provide valuable protection for your hom e and prope rty if uti lized properly. However, this unit cannot guarantee complete protection against to burglary or robbery. Therefore, we will not be responsible for any losses or damages which could occur. 1. Telephone Line Jack 2. Telephone Jack RS t t wL z e 5. Ex Power ^-i DD sp ^ S um er i ca eys ^ = 9. DC 9V Power Jack 10. Chime on/off Switch 11. Battery Cover 12. External Terminal 13. 9V Battery FEATURES • Motion Sensor, detects motion activates auto-dialer and alarm • 14 Digit large number display with dateltime • Programmable security code, entry delay timing • 5 emergency telephone numbers (up to 32 digits each) • Programmable auto dialling cycle • 5 Trigger recorder for alarm mode • PAUSE key • PANIC key • PROG y • Buitt-in flash memory to protect system data for power failure -1- • Battery Low indicator • Tone dialling only • Chime ON/OFF switch • Built-in 105 dB alarm (with programmable alarm on/off) • Adjustable sensor head • External extend trigger input terminal (compatible magnetic sensor. PIR slave unit. Water alarm). • External siren terminal (compatible outdoor siren) • AC adaptor op erated (included) with 9V battery back-up (not included) • Wall mountable 1. Remove the screw of m ain unit from battery compartment cover, install an alkaline 9V battery, this is a back-up battery, in case of AC power failure. This battery will keep the unit working (fig.1) o c a (fg 1) 2. Connect the line cord between LINE jack and telephone wall socket. (fig.2a) 3. Now connec t the plug/wire included with your auto-dialer (this is the plug/wire with the clear plugs at either end) one end inserted in the TEL socket on the auto-dialer, and the other end into your telephone. You now ha ve a wire from the TEL socket on yo ur auto-dial er to your telephone. You shou ld now have a dial tone. 4. Plug the AC adaptor to the DC 9V socket on the auto-dialer (Fig. 2b) Telephone Line Socket ( flCg. 2b ) fig. 2a ) ^^ 5. For wall mount-If required Choose a suitable location, 5- 6 feet (1.5 - 2.0 meters) away from floor, drill holes and install anchors and screws Place the unit over the screws and slide it down to secure in place (fig 3). It is suggested that you m ount the unit this distance above the floor to obtain the best co verage of the intended protected area.(Fig 3) 2 7 -7 1 fi ) 6. For shelf top- Turn the sensor head 90 degrees upwards, then rotate the head 180 desired clockwise to the desired angle. Place in on the shelf-top location you selected (fig.4) Upwards 90°Rotate 180 ( ft9' 4) Unit -----1^ - ^ PRECAUTIONARY NOTE: IF YOU HAVE ANIMALS Sensor head can be adjusted if you have dogs, ie. you would set the sensor head slightly higher avoiding your animal. We suggest that if you have cats to keep them out of the room that the Auto Dialer is mon itoring. • This program can only be operated during disarm mode. During set-up, if not key in any message within 10 seconds, the system will auto exit set-up mode. • Your auto-dialer has a factory preset pass number of 0-0-0. This can now be changed to a pass number personal to you. ^ g 1 TO CHANGE PASSWORD a. Enter factory pre-set pass number, 0-0-0. Press PROG button once, PASSWORD will fl ash on the auto-dial er screen. b, Press the ARMlDtSARMbutton to confirm that you want to enter the PASSWORD option. c. Enter your new pass number followed by the ARM/DISARM button to confirm the new number. (you can choose up to 6 numbers in your pass number) d. Press the PROG button seven ti mes to exit set-up mode. NOTE: If you forget your pass number, press and hold down the PROG button, for up to 2 seconds, after a beep press PAUSE button, remove the battery and A C adapter after 2 -3-
