AUTOMATIC DOOR ACTIVATION SOLUTIONS - Wikk Catalog.pdf · Wikk Bollard Options: For technical assistance, consult your local distributor or representative, visit wikk.com, or call

2014 CATALOG

Standard &Customized Bollards

Customized SwitchesWireless and Touchless

Standard Switches,Key Switches & Mounts the

INGRESS’R®

Specified in: MasterFormat™ Section 08710 (08 71 20) Automatic Door Controls

AUTOMATIC DOOR ACTIVATION SOLUTIONS

SWITCHES MOUNTING OPTIONS

• All AccessAbility™ switches are ready for wireless or hard-wired applications to flush mounted single-gang or double-gang electrical junction boxes.

• A variety of surface and flush mounts give you the flexibility you need to meet the specific requirements of your installation (design, energizing, visibility, safety) described on corresponding switch pages.

• The red asterisk (*) = a Radio Frequency-compatible mount.

NOTE: Exterior application - for moisture evaporation drill 1/32” weephole in the bottom of box.

WKS-471/4” Dia. X 11/4” O.D.

(184 X 30 mm)1” Inside Depth (25 mm)

WKS-4RF713/16” Dia. X 19/16” overall ht.

(200 mm X 40 mm)125/64” Inside Depth (35.5 mm)

SURF 4/M4 X 4 X 11/8” O.D.

(102 X 102 X 29 mm)11/8” Inside Depth (29 mm)

SURF 6/M4” W X 4” H X 3/4” D

(102 X 102 X 19 mm)3/4” Inside Depth. (19 mm)

SURF 4R23/4” X 41/2” X 111/16” D(70 X 114 X 43 mm)

19/16” Inside Depth (40 mm)

6R

SPBSFA KS-P

NS AA KS-N

4R

4x4

KS-4

*

*

SURF SFA23/4” X 41/2” X 15/8” O.D.


SURF 6/M4” X 4” X 3/4” O.D.


6x6

WKS-691/2” Dia. X 1” Overall Height

(241 X 25 mm)7/8” Inside Depth (22 mm)

SURF SQ 4 & 6 BLK419/32”W X 419/32”H X 13/4”D


JSB13/4” X 49/16” X 13/4” O.D.


SURF 4R23/4” X 41/2” X 111/16” D


*

*

*

N6RS67/16” Dia. X 21/8” H

(164 X 54 mm)115/16” Inside Depth (49 mm)

N4RS5” Dia. X 21/8” H (127 X 54 mm)

115/16” Inside Depth (49 mm) *

N4RF57/8”Dia. X 21/8” H

(149 X 54 mm) with trim ring115/16” Inside Depth (49 mm)

6” Square BOLLARD

6” Square BOLLARD

4” or 6”Square

BOLLARD*

Switch and Mounting Compatibility Chart

*

*

*

N6RF73/4” Dia. X 21/8” H

(197 X 54 mm) with trim ring 17/8” Inside Depth (48 mm) *

*4” or 6”Square

BOLLARDRequiresAA prep *

*

*

6” RoundBOLLARD

*

6” Square BOLLARD

*

*

N4X4F63/4” X 63/4” X 21/8”

(172 X 172 X 54 mm)17/8” Inside Depth (47.6 mm)

*

N4X4S51/2” W X 51/2” H X 21/8” D

(140 X 140 X 54 mm) 5” X 5” Inside (127 X 127 mm)115/16” Inside Depth (49 mm) *

SURF 6R419/32” W X 419/32” H X 13/4” D


+CUFF

6” Square BOLLARD

*

6” RoundBOLLARD

*

+CUFF

6” RoundBOLLARD

*

+CUFF

6” SquareBOLLARDRequires

INGRESS’R® prep *

8” RoundBOLLARD

*

+INGRESS’R®

CUFF

PRODUCT IDENTIFICATION CODE––––––––––––––––––––––––––– SWITCHES ––––––––––––––––––––––––––––––––––––– BOLLARDS ––––––––––4R = 41/2” Round AA = All-Active BPS = Bollard Post Square4x4 = 41/2” by 41/2” Square NS = Narrow Style BPR = Bollard Post Round 6R = 6” Round KS-N = Key Switch Narrow BPRT = Bollard Post Rectangular6x6 = 6” by 6” Square KS-P = Key Switch Prep BPTR = Bollard Post TriangleSFA = Single gang Full-Active KS-4 = Key Switch 4x4 SM = Surface MountSPB = Single gang Push Button I36 = INGRESS’R® 36” Length IG = In Ground

NOTE: N4RF is flush mounted

NOTE: N6RF is flushmounted

NOTE: N4X4F is flush mounted

* =

SURF SQ 4 & 6 BLK419/32”W X 419/32”H X 13/4”D


INGRESS’R®

1For technical assistance, consult your local distributor or representative, visit wikk.com, or call 877.421.9490

GEN

ERAL IN

FORM

ATIO

N

Benefits and Value ofworking with Wikk:

SWITCH OPTIONS• Decorative materials and finishes• Custom Engraving –

legends, logos, image and texts• Custom Infill coloration- Chocolate Brown,

Green, Red and White; also available in our standard Blue and Black infill

• Grade 2 Braille lettering• Weather (WR) and infiltration-resistant• Double Pole Double Throw (DPDT)

micro-switch for dual operations (example: for lock release)

• Quick-connect wireless products for Radio Frequency operation (See page 18-19)

• Pneumatic operation, used in fail-safeexit, hazardous area that requires noelectrical charge

• Anti-Microbial Coating

Standard (STD)SATIN STAINLESS STEEL US32D (630)Type 304 - 18 Gauge

MIRROR BRASS US3 (605) UncoatedType Naval Brass - 18Gauge

SATIN BRASS US4 (606) UncoatedType Naval Brass - 18 Gauge

MIRROR STAINLESS STEEL US32 (629)Type 304 - 18 Gauge

OIL-RUBBEDand RELIEVEDOXIDIZED BRASSUS10B (613)

Type Naval Brass - 18 Gauge

Standard (STD)Switches are debossed and infilled with color (stocked)

Non-standardSwitches are engraved and infilled or debossed,depending on the design and quantity ordered.(Lead time approximately 2 -3 weeks)

These finish colors are printer’s reproductions and may vary from actual colors. Call for samples.Switch Cover Materials and Finishes

For more than 30 years Wikk AccessAbility™ switches and bollards have been manufactured in the USA at our Wisconsin factory. We use quality materials and craftsmanship to ensure dependability in hightraffic areas and harsh weather conditions.

AccessAbility™ products meet or exceed accessibility requirements around the world such as the ADA,AODA, The Equality Act of 2010, Australia’s Premises Standards of 2011, and more. The AccessAbility™line is applicable, and not limited to CSI Divisions 5, 8, 14 and 28.

AccessAbility™ switches can be customized with special engraving (logos, images, and text), Grade 2 Braille,infill colors and material finishes.

Project-specific requirements for access control, communication and accessibility can be attractively coordinated within a custom Wikk bollard, and manufactured from a wide variety of materials and finishesto complement architectural design.

The contents of Wikk products exceed the minimum recommended percentages of recycled materials and thecompany supports green initiatives by utilizing North American products and suppliers as much as possible.

Wikk provides an 18 month warranty on switches and bollards from the date of shipment and 24 months on wireless products from the date of manufacture.

Every day we exceed our customers’ expectations with friendly customer service and reasonable lead times. We look forward to working with you on your next project.

MADE IN

U.S.A.

For Bollard Options see page 2

Wikk Bollard Options:

For technical assistance, consult your local distributor or representative, visit wikk.com, or call 877.421.9490

Standard & Custom BOLLARD POSTS

Standard Lead-times:Standard bollards: Same day shipping if ordered by noon CST.Custom bollards: Lead-time is 1-5 weeks

depending on the design. Shape:• BPS = Square • BPR = Round• BPRT = Rectangular • BPTR = TriangleMounting Installation options:• SM = Surface mount: standard posts are 42” [1067 mm]

high, single gang prep @ 36” CL/AFF [914 mm]; includesaluminum anchoring base, anchors and instructions.

• IG = In-ground: standard posts are 54” [1372 mm]high, single gang prep @ 36” CL/AFF [914 mm] including 12” [305 mm] recess and instructions.

Overall height: • Can be customized to be shorter or taller than standard height.Architectural Materials & Finishes:Square (BPS) Aluminum Tubes:• Anodized Aluminum: Clear (628), Dark Bronze (710),

Black (711), and Mill finish for painting (PT) or powder coating (PC); Light BronzeAnodized (available for 6” square bollards only)

• Wall Thickness and Corner Radius for Aluminum: Extruded; nominal 1/8” [3.175 mm] wall thickness, 4” and 6” Square: 1/32” corner radius

Square (BPS) Stainless Steel Tubes:• Satin Stainless Steel US32D (630) or Mirror Stainless

Steel US32 (629) finishes • Wall Thickness and Corner Radius for Square Stainless Steel:

Welded type 304; nominal 1/8” [3.175 mm] wall thickness 4” and 6” Square: 15/64” corner radius • 316 alloy available as special order

Brass Clad Aluminum (Square only):Nominal 18/19 gauge sheet metal over standard Aluminumextrusion, 9/64 corner radius• Satin Brass US4 (606 uncoated) or Mirror Brass US3

(605 uncoated) finishes. Protective coating by others.Round (BPR) Aluminum Tubes:• Anodized Aluminum: Dark Bronze (710) and Mill finish

for painting (PT) or powder coating (PC)• Powder coated (PC): To match Clear Anodized Aluminum • Wall Thickness: Extruded; nominal 5/32” [4 mm] wall thicknessRound (BPR) Stainless Steel Tubes:• Satin Stainless Steel US32D (630) or Mirror Stainless

Steel US32 (629) finishes • Wall Thickness for Square Stainless Steel: Welded type

304; nominal 1/8” [3 mm] wall thickness • 316 alloy available as special order

2

Preps:• INGRESS’R®, standard and narrow style switches, card

readers, intercoms, KNOX-boxes, fire pull stations and more.• Square (BPS), Rectangular (BPRT) and Triangle (BPTR)

Bollards: Switches and devices mount directly to post.• Round (BPR) bollard: Curved switch (6C series) mounts

directly to post. Use Adapter Cuff for additional items orflat switch styles. Round bollards can be modified withrecessed insert area to accommodate flat devices.

***At the time of quoting/ordering bollards we require the make, model, as well as mounting templates ofall the devices to assure accurate preps.***

Production will not start until the device information is provided. All information is kept confidential.Cap style & finish:• Flat top (FT): Standard black removable top

(allows RF transmission)• Flat top (FT): Stainless Steel, Aluminum and Brass

removable top (not available for round bollards)• Flat top (FT): Welded Flat Top for Stainless or Mill Aluminum

for painting (PT) or powder coating (PC) finishes• Angled top (AT): Welded Stainless Steel, or Mill Aluminum

for painting (PT) or powder coating (PC) finishes; alsoavailable in Removable Angle Top (RAT)

• Dome (D): Round only, Welded Stainless, or Mill Aluminumfor painting (PT) or powder coating (PC) finishes

Additional Options:• Special sizes available per request - See Wikk’s

Bollard Checklists on website.Example: 3”x 3”, 7”x 7” , 9”x 9” , 6”x 9” , 6”x 12” and Triangle Bollards available in Stainless Steel,Aluminum and Steel. Sizes are subject to change without notice.

• Painted (PT) or Powder coated (PC) finish available • Exposed Base Plate - different sizes available in round

(RB), square (SB), rectangle (RTB) and concealed sleeve (CS) with base plate for In-ground mounting withadditional anchoring, 7” bolts and anchors

• Access Panel (AP) - Removable access panel on the backof bollard or the insert area with security screws.

• Hood - Added over devices to help protect from environmental conditions.

• Decorate Reveal (R) - Decorative reveal in the metal.

For additional custom design solutions: Contact Wikk Industries, Inc.

SATINSTAINLESS STEEL

(630)

MIRRORSTAINLESS STEEL

(629)

SATIN BRASS CLAD(606-uncoated)

(Square Only)

MIRROR BRASS CLAD(605-uncoated)

(Square Only)

CLEAR (628) DARK BRONZE (710)

LIGHT BRONZE(Square Only)

BLACK (711)(Square Only)These finish colors

are printer’s reproductions

and may vary from actual

colors. Call for samples.

COLORKEY


Part # BPS SM-PRP36 LB6” x 6” x 42” Tall,

Light Bronze Anodized AluminumSurface mount with

concealed mounting base, 1 Prep at 36” AFF for ADA switch,

Removable Black ABS cap

Part # BPR SM-AINS 32D6”Rd x 48.625” Tall,

304 Satin Stainless SteelUS32D (630),

Surface mount with concealed mounting base,

Recess area for flat devices,Welded Angle top (front slant) (AT)

Part # BPR SM-PC CLEAR

6”RD x 42” Tall,Powder coated (PC) to match

Clear Aluminum,Surface mount with

concealed mounting base,1 prep at 36”AFF for

Wikk 6C-5 WR US32DADA curved switch,


Part # BPDSMPREP36 PTDB

6”RD x 45” Tall, Mill Aluminum, painted (PT)

to match Dark Bronze Aluminum,Surface mount with

concealed mounting base,1 prep at 36” AFF for

Wikk 6C-3 WR US32DADA curved switch,

Welded Dome Top (D)

3

Part # BPS SM TUBE 32D6” x 6” x 42” Tall,

304 Satin Stainless Steel in US32D (630),


1 prep at 36” AFF for ADA switch,


Part # BPS SM-ING48 DB

with I36-3 Clear 6”x 6” x 48” Tall, Dark Bronze

Anodized Aluminum (710), Surface mount with

concealed mounting base,2 Preps for INGRESS’R®

and card reader, Removable Black ABS Cap

Part # BPR SM US326”RD x 42” Tall,

304 Mirror Stainless SteelUS32 (629),


1 prep at 36”AFF for Wikk 6C-3 WR US32 ADA curved switch,


Part #BPS IG-HI/LO CLEAR

6” x 6” x 54” Tall, Clear Anodized Aluminum (628),

In-ground mount,2 preps for ADA switches,Removable Black ABS cap

Part #B4S SM-PREP36 CLEAR4” x 4” x 42” Tall, Clear

Anodized Aluminum (628),Surface mount with

concealed mounting base, 1 Prep at 36”AFF for ADA switch,


BO

LLARDS

Part #BPS SM-INGR DK BZ

with I36-5 Dark Bronze6” x 6” x 42” Tall, Dark Bronze

Anodized Aluminum (710),Surface mount with concealed

mounting base,1 prep for INGRESS’R®

ADA switch,Removable Black ABS cap


Standard & Custom BOLLARD POSTS

4

Standard Bollard CapsSquare shown; same features in round.See page 18 and 19for wireless products.

Hard-Wire and Wireless

SHOWN WITH SWITCH

(Sold separately)

THE EDGEGETPart # 4x4 Edge US32D

SQUARE ONLY SQUARE & ROUND

Hard-Wire and Wireless (with standard bollard cap)

Wikk AccessAbility™ Exclusive!

1-Gang Adapter CuffPart# BP4X4ADTRFBLK• Sturdy, textured black ABS material• Multi-purpose use– A mounting bridge between a flat

device and round bollard (card/proximity reader, switch, etc.)

– Allows RF transmission when metal bollard cap is utilized

– Alternative to 6C series switch • Cuff mounts onto bollard 1-gang prep.

Device mounts directly to 1-gang face prep of the cuff.• 1-5/8” (41 mm) profile, not including device• 4-1/2” x 4-1/2” (114 x 114 mm) O.D. • Also available in Stainless Steel

(does not allow RF transmission)• Stainless Steel and Aluminum posts can be

fabricated with a recess for flat devices

• A dramatic look with high visibility• 6”x 6” (152 x152 mm)• Standard finish is US32D (630)• 316 Alloy• Heavy-duty 1/8 ” (3 mm) thick material• Weather-resistant (WR)• Radius conforms to bollard design

OPTIONS:• Finishes: US32 (629), US4 (606 uncoated),

US3 (605 uncoated), US10B (613)• Custom engraving• Hard-wire and Wireless

6 x 6 Curved Switch

Additional Options

Part# 6C-3 WR (shown)Part# 6C-5 WR (ADA logo only) also available

ROUND ONLY

ROUND ONLY

411/16” tall X 47/8” wide X 1/2” deep (118 x 124 x 8 mm)

Sturdy 3-sided stainless shroud protects the switchcomponents from harsh environmental conditions and

wash down chemicals. Especially effective againstfreezing rain and snow infiltration to prevent temporary

ice buildup. Offers a decorative appeal by concealing thegap between the faceplate and backplate of the switch.Insert between the bollard and backplate of the switch.

Recommended for exterior bollards.

Access PanelRemovable Access Panel (AP)on the back of bollards or the insert area with security screws

Reveals (R)Decorative Reveal in the material

Removable Angle Top (RAT)to allow access with a

decorative touch

Concealed Sleeve for In-ground mountingAvailable: Round Base (RB), Square Base (SB) or Rectangular Base (RTB)

Base PlatesExposed Surface Mount with mounting holesAvailable: Round Base (RB), Square Base (SB) orRectangluar Base (RTB) not shown.

For technical assistance, consult your local distributor or representative, visit wikk.com, or call 877.421.9490 5

BO

LLARDS

Part # BPRT126SMFT32D12”x 6”x 42” Tall,

7ga. Formed 304 SatinStainless Steel US32D (630)


1 prep for INGRESS’R®

ADA switch,Welded Flat Top (FT)

Part # BPR8 SM AINS32D

8” Rd x 45” Tall,304 Satin Stainless Steel

US32D (630),Surface mount with

concealed mounting base, Flat Recessed area for ADA switch and Card

Reader, Welded Angle Topto the back (AT)

Part #B3FSMRBPRP3632D

3”x 3”x 42” Tall,304 Satin Stainless Steel US32D (630),Surface mount with welded round base plate (RB), 1 Prep for ADA switch,

Welded Flat Top (FT)

Part #BPRT96SMSBAT32D

9”x 6”x 48” Tall,7ga. Formed 304 Satin

Stainless Steel US32D (630),

Surface mount with welded square mounting base plate (SB),1 prep for

Keypad/Card Reader,Welded Angle Top (AT)

Part #BPSSMAHOODH/L32D

6”x 6”x 42” Tall, 304 Satin Steel in US32D (630),

Surface mount with concealedmounting base, 2 preps with

Stainless Steel hood over the upper ADA Switch,Welded Angle top (AT)

(front slant)

Part # BPSSM36RATPCDK6”x 6”x 54” Tall,Mill Aluminum

Powder coated (PC) to match Dark Bronze Aluminum,


1 prep for ADA switch,Removable Angle top (RAT)

(front slant)

Part # BPS IG CS 32D6”x 6”x 48” Tall,

304 Satin Steel in US32D (630),

Removable bollard for In-ground mounting withconcealed sleeve (CS)

and base plate,2 preps for ADA switch

and Card reader,Removable Black ABS cap

Part #BPTR6SMRBP3632D6”x 6”x 6”x 42” Tall,

TRIANGLE7ga. Formed 304 Satin

Stainless Steel US32D (630),

Surface mount with weldedround base plate (RB),1 Prep for ADA switch,Welded Flat Top (FT)

Part #BPD8SMRBINS32D

8” Rd x 54” Tall,304 Satin Stainless Steel

US32D (630),Surface mount with

12” round mounting baseplate (RB), Flat Recessedarea for Intercom, ADA

switch and Card Reader,Welded Dome Top (D)

Part #BPR10.75AINS32D

10.75” RD x 54” Tall,304 Satin Stainless Steel

US32D (630),Removable Bollard for In-groundmounting, Flat Recessed area

for ADA switch and Card Reader,1 Prep on the angle top

for intercom,Welded Angle Top (AT)

”Best Bollards in the business”say our customers and our competitors


The contoured profile of The INGRESS’R® allows activation from literally any approach and height level.

ingress\`in-gres\ n: 1. the act of entering 2. the power or liberty of entrance or access

It’s the logical choice. Achieve architectural integrity with ADA compliance – all in one – with the patented design, exclusive to Wikk!

OPTIONS - STANDARD1 = Plain, no legend2 = Push to Open3 = Push to Open5 =

• Models without legends are available

OPTIONS - CUSTOM• Custom legends and lights• Narrow widths and custom heights• Finishes:

Clear (628), Dark Bronze (710), US32D Satin Stainless (630), US32 Mirror Stainless (629), US4 Satin Brass (606 uncoated), US3 Mirror Brass (605 uncoated), US10B Dark Oxidized Satin Brass, oil-rubbed (613)

SLEEK, TAPERED PROFILE• Deflects impact from wheeled carts and

conveyances

• Naturally directs movement toward central activation column

• No squared-off edges to get caught on

• Offers vandal deterrence: no gaps or edges to pry; ABS cap is secured by spanner screws

• Weather-resistant: no gaps for water or ice to penetrate; free draining

• Add switch transmitter and receiver for wireless activation (see pages 18 & 19)

36” TALL x 6” WIDE x 11/2” DEEP(914 mm x 152 mm x 38 mm)

• Mounts on most wall surfaces–including uneven

• Fits precisely on 6” (152 mm) x 6” (152 mm) bollard post when wall mounting is impractical

• Recommended mounting height is 3” (76 mm) from finished floor

RUGGED, YET SENSITIVE• Dependable micro-switch: 15 amp, 125/250VAC,

UL® & CSA listed• Sturdy, 1/8”(3 mm) extrusion (nominal) with

superior finishes• Actuates from literally all points on the

activation column

FEATURES and BENEFITS

Legend Colors:• Blue on Clear, Brass

and Stainless • White on Dark Bronze

For Custom INGRESS’R see pages 8 & 9

TheINGRESS’R®

TOP VIEW of STANDARD INGRESS’R

showing tapered profile11/2” (38 mm) depth

Part # I36-5 DKBZDark Bronze Anodized

Aluminum (710) with white ADA logo

Shown on Bollard(Sold Separately)

Part #

BPS SM-INGR DKBZ

Part # I36-3 ClearClear Anodized

Aluminum (628) with blue ADA

logo & text “PUSH TO OPEN”

36” (914 mm)length by 2.5” (64 mm) width

CENTER ACTUATION

COLUMN

36” (914 mm) length by 6”

(152 mm) widthby 1.5”

(38mm) depthCONTOURED BASE

6”(152 mm)

1.5”(36 mm)

▲

▼


The I

NG

RES

S’R

®

A 36” Column of Touch Activation TThhee IINNGGRREESSSS’’RR®

Specified in: MasterFormat™ Section 08710 (08 71 20) Automatic Door Controls

”By simply bumping the INGRESS’R with the footrest of my wheelchair, I am able to activate the switch to opena door. It’s such a clean, simple, truly functional solution –and the end result is a welcoming design that leaves no one out, whether the building is modern, post-modern, or a historic restoration.”

Harold Dean Kiewel, AIA, CSI, CCSassociate/sr. specifications writer, HMC Architects

WIRELESSOption: Connect transmitter to wire harness and secure with double-sided tape near cap.

HARD-WIREConduit access points in base at 3” (76 mm)

from top and 10” (254 mm) from

bottom

END VIEW of NARROW INGRESS’R

4.25” (108 mm) wide at cap

A 9” version of the INGRESS’R can be used as a wall switch with a sleek,tapered design. Capped at both ends.

Part # I09-3 ClearClear Anodized Aluminum (628) with blue ADA logo & text “PUSH TO OPEN”

Part #

I36-3 NAR ClearClear Anodized Aluminum (628)

with blue ADA logo & text “PUSH TO OPEN”

The vertical actuation bar also provides simplified door entry to a variety of people – even those who simply have

their hands full or are pushing a cart – in many different settings like healthcare facilities and universities.

Trusted Innovation for more than10 years!delivers

4.25” (108 mm)with cap

1.6” (41 mm)Side Viewwith cap

4.25”(108 mm) CAP

1.6”(41 mm)

▲

▼

Narrow INGRESS’R®

Finishes


CUSTOMIZE TheINGRESS’R®

Custom Options:• Custom Legends: Numbers, Letters, Arrows or Symbols

• Custom Light Colors with black bezel:

• CustomHeight:9” to 42” tall

Column of Touch Activation

• Lights available in 28 volt or 120 voltWhite Amber Blue Yellow Red

Part # I09-3 CLEAR6” Wide x 9” Tall Clear Anodized

Aluminum (628)ADA Legend

Part # I24-? CLEAR6” Wide x 24” Tall

Clear Anodized Aluminum (628)Custom Legend:

OPEN DOOR and Door Open Symbol

Part # I30-? CLEAR6” Wide x 30” Tall

Clear Anodized Aluminum (628)

Custom Legend: E

Part # I36-5AL DARK BRONZE

6” Wide x 36” Tall Dark Bronze

Anodized Aluminum (710)ADA Legend and Arrow Left

Part # I42-3 CLEAR6” Wide x 42” Tall

Clear Anodized Aluminum (628)

ADA Legend

SATINSTAINLESS STEEL (630)

US32D

MIRRORSTAINLESS STEEL (629)

US32

SATIN BRASS CLAD(606-uncoated)

US4

MIRROR BRASS CLAD(605-uncoated)

US3

DARK OXIDIZEDSATIN BRASS

Oil Rubbed (613)US10B

CLEAR (628) DARK BRONZE (710)

These finish colors areprinter’s reproductions

and may vary from actual colors.

Call for samples.

COLORKEY


The I

NG

RES

S’R

®

Other custom legends available.(Examples shown on page 8)

LIGHT INDICATES ELEVATOR ACTIVATION

ELEVATORALARM CAB

SWITCH

ELEVATOR UPHALL

SWITCH

Wikk’s INGRESS’R elevator cab and hall switches are featured in The Blusson Spinal Cord Centre – the new homefor the ICORD in the Vancouver General Hospital site in Vancouver, British Columbia, Canada.

Photo courtesy of ICORD

“We are also most pleased with the Wikk elevator solution in our building.It has been universally praised by all, from high cervical tetraplegics usingsip-and-puff motorized wheelchairs, to the regular users of the building, tothe Premier of BC and the Federal Minister of Health. A great success!”Chris McBride, PHDManaging DirectorICORD (International Collaboration On Repair Discoveries)

“The challenge that Wikk was ableto meet is delivering on an inno-vative approach that allows totalaccess to someone in a wheelchairthat really doesn’t have the ability to push a button. And Wikkachieved it cost-effectively whileensuring that the switches were aesthetically pleasing.”

Paul Baker, project manager with KONE on Wikk’s INGRESS’R customization capabilities

CUSTOMIZE TheINGRESS’R®

delivers


PART NO. LEGEND

4x4-3

4x4-3AL

4x4-3AR

4x4-1

4x4-2

4x4-4

4x4-5

4x4-11

4x4 Series switchesmount directly onto 1-gang prep of standard Wikk bollards.

(See page 2 and 4 for bollard details.)See page 1 for switchcover materials, finishes,and options.

Blank – No Legend

PUSH TO OPEN(Black Infill)

PRESS TO OPERATE(Black Infill)

(Blue Infill)

PUSH TO OPEN(Blue Infill)

PUSH TO EXIT(Black Infill)

PUSH TO OPEN

(Blue Infill)

PUSH TO OPEN

(Blue Infill)

SURF 4/M4” W X 4” H X 11/8” D (102 X 102 X 29 mm) 11/8” Inside Depth (29 mm)

Clear (628) or Dark Bronze (710) Anodized Aluminum ring with plated mounting bracket.Similar to SURF 6/M shown on p. 12.

Hard-Wire only

SURF SQ 4 & 6 BLK419/32” W X 419/32” H X 13/4” D (117 X 117 X 44 mm)


Black ABS box with unique battery change-out compartment. Battery can be exchanged without switch

removal. Tamper-resistant: compartment door is held in place by

the switch and cannot be removed or lost. Switch mounting plate is recessed,

presenting a finished appearance.


Registered design; distributed by Wikk Industries

CRAFTSMANSHIP combined with

TECHNOLOGICAL INNOVATION

SHOWN WITH 4x4 SERIESSWITCH AND BATTERY(Sold separately)

4x4 SERIES DOOR SWITCHESStandard Satin Stainless Steel US32D (630)

4x4 Series Surface Mounts

N4X4F FLUSH MOUNT63/4” W X 63/4” H X 21/8” D (172 X 172 X 54 mm) 5” X 5” Inside (127 X 127 mm)

17/8” Inside Depth (47.6 mm)

SHOWN WITH SWITCH(Sold separately)

THE EDGEGET

N4X4S SURFACE MOUNT51/2” W X 51/2” H X 21/8” D (140 X 140 X 54 mm) 5” X 5” Inside (127 X 127 mm)


Durable black ABS enclosure, designed formounting flush into hollow wall. Features amolded-in 7/8” (22mm) wide trim ring andmounting bracket. Includes required weather-resistant gasket plate. Hard-Wire or

Wirelessif mounted into

RF-transparent wall materials.

2 1/8” (54mm) projection. 4X4 switch sitsflush within this durable ABS enclosure,insuring a high degree of tamper-resist-

ance. Includes required weather-resistantgasket plate. Hard-Wire or

Wireless

4x4 Edge US32D (630)411/16” H X 47/8” W X 1/2” D

(118 X 124 X 8mm)Sturdy 3-sided stainless shroud to protect the switch components

from harsh environmental conditions or in areas where walls are subjected to wash down chemicals. Especially effective

against freezing rain and snow infiltration to prevent temporary ice buildup. Offers a decorative appeal by concealing the gap

between the faceplate and backplate of the switch. Insert betweenthe mounting surface and the backplate of the switch.

Recommended for exterior applications.


WKS-4 US32D (630) 71/4” Dia. (184 mm) 11/4” overall height (30 mm)1” Inside Depth (25 mm)Highly functional as it is decorative, this escutcheon offers a distinctive and tamper-resistant presence for the switch. The wall-hugging, slanted contour prevents snagging and shear-off from hand-propelled vehicles. Available in the same materials and finishes as AccessAbility™ switches.Part# WKS-4SS WRRING For weather resistanceHard-Wire only

WKS-4 RF BLACK 713/16” Dia. (200 mm) 19/16” overall height (40 mm)125/64” Inside Depth (35.5 mm)A Wik-scutcheon in Radio Frequency (RF) transparent material. The same design and functionality as our metal escutcheon, but manufactured in textured, durable black ABS. This is an economical alternative with another advantage: wireless transmission. Features a rubber seal and caulking groove on the reverse side and a transmitter pocket. Can be painted to match décor. Part# WKS-4RF WRRING For weather resistanceHard-Wire and Wireless


4” S

QUARE &

RO

UN

D S

WITC

HES

N4RS SURFACE MOUNTED 5” Dia. X 21/8” H (127 X 54 mm)115/16” Inside Depth (49 mm)21/8” (54mm) projection offers a distinctive presence.4R switch sets flush within this good-looking, durable ABS enclosure, ensuring a high degree of tamper-resistance. Add N4WR gasket for weather-resistance.Hard-Wire and Wireless

4R Series switchesmount directly onto

1-gang prep of standard Wikk bollards.

(See page 2 and 4 for bollard details.)

See page 1 for switchcover materials, finishes,

and options.

LEGEND PART NO.

4R-3

4R-1

4R-2

Blank – No Legend


PUSH TO EXIT(Black Infill)

4R-4PRESS TO OPERATE

(Black Infill)

4R-3ALPUSH TO OPEN

(Blue Infill)

PUSH TO OPEN

(Blue Infill)

4R-3AR

4R-5

4R-11

(Blue Infill)

SURF 4R23/4” W X 41/2” H X 111/16” D (70 X 114 X 43 mm)19/16” Inside Depth (40 mm)Brown phenolic box with corner-covering aluminum adapter plate topresent a finished look. Micro-transmitter (SWTRAN-M series) fitsneatly into mount. Hard-Wire and Wireless

Wikk deliversCONSISTENT QUALITY–

Door SwitchesYou Can Count On

SHOWN WITH SWITCH

(Sold separately)

WKS-4RFWRRINGWeather-Resistant GasketProvide a self-sealing barrier from moisture or dirt entering cavity of mounts. Use in high infiltration conditions.Also available for WKS-4 US32D Part# WKS-4 SSWRRING

N4WR Weather-Resistant GasketProvide a self-sealing barrier from moisture or dirt entering cavity of mounts. Use in high infiltration conditions.

A WIKK EXCLUSIVE!Wik-Scutcheons


4R SERIES DOOR SWITCHESStandard Satin Stainless Steel US32D (630)

4R Series Surface Mounts


N4RF FLUSH MOUNTED57/8”Dia. X 21/8” H (149 X 54 mm) with trim ring115/16” Inside Depth (49 mm)Same material and qualities as N4RS, but designed for mounting flush into hollow wall. Features a molded-in 7/8” (22 mm) wide trim ring and mounting bracket. Add N4WR gasket for weather-resistance.Hard-Wire or Wireless if mounted into RF-transparent wall materials.

BACK

BACK

11

6x6 SERIES DOOR SWITCHESStandard Satin Stainless Steel US32D (630)


6x6 Series Surface MountsPART NO. LEGEND

6x6-3

6x6-1

6x6-2

6x6-4

6x6-5

Blank – No Legend




6x6-3AL

6x6-3AR

(Blue Infill)

PUSH TO OPEN

(Blue Infill)

PUSH TO OPEN

(Blue Infill)

6x6 switches are the most cost-effective to stock:

they mount to the three most typical junction boxes

found on jobsites.

SURF SQ 4 & 6 BLK419/32” W X 419/32” H X 13/4” D


Black ABS box with unique battery

change-out compartment.

Battery can be exchanged without switch removal.

Tamper-resistant: compartment door is

held in place by the switch and cannot be removed

or lost. Switch mounting plate is recessed.

6x6 switch cover extends 3/4” (19 mm) beyond

mount on all sides.



SURF 6/M4” W X 4” H X 3/4” D (102 X 102 X 19 mm)

3/4” Inside Depth. (19 mm)

Clear (628) or Dark Bronze (710) anodized

aluminum ring surrounds galvanized mounting plate to

create an attractive surface mount. 2-piece unit.

Hard-Wire only

SHOWN WITH 6x6 SERIES SWITCH AND BATTERY (Sold separately)

6x6 Series switchesmount directly onto 1-gang prep of standard Wikk bollards.

(See page 2 and 4 for bollard details.)See page 1 for switchcover materials, finishes,and options.

See pages 18 & 19 for

wirelessoptions

6R SERIES DOOR SWITCHESStandard Satin Stainless Steel US32D (630)


6” S

QUARE &

RO

UN

D S

WITC

HES

SHOWN WITH6R SERIES

SWITCH AND BATTERY

(Sold separately)

LEGEND PART NO.

6R-1

6R-2

6R-3

6R-3AL

6R-3AR

6R-4

6R-5

Blank – No Legend




(Blue Infill)

PUSH TO OPEN

(Blue Infill)

PUSH TO OPEN

(Blue Infill)

SURF 6R419/32” W X 419/32” H X 13/4” D(117 X 117 X 44 mm)11/2” Inside Depth (38 mm)

Surf SQ 4 & 6 BLK black ABS box with aluminumcorner-covering adapter plate to present a finished appearance.Features a unique battery change-out compartment. Battery can be exchanged without switch removal. Tamper-resistant: compartment door is held in place by the switch and cannot be removed or lost.


N6RS SURFACE MOUNTED 67/16” Dia. X 21/8” H (164 mm X 54 mm)115/16” Inside Depth (49 mm)

21/8” (54 mm) projection offers a distinctive presence.6R switch sets flush within this good-looking, durable ABSenclosure, ensuring a high degree of tamper-resistance. Add N6WR gasket for weather-resistance.


N6WR Weather-Resistant GasketProvide a self-sealing barrierfrom moisture and dirt entering cavity of mounts. Use in high infiltration conditions.


BACKFRONT

WKS-6 US32D (630)91/2” Dia. (241 mm) 1” overall height (25 mm) 7/8” Inside Depth (22 mm)

Highly functional as it is decorative, this escutcheon offers a distinctive and tamper-resistant presence for the switch. The wall-hugging, slanted contour prevents snagging and shear-off from hand-propelled vehicles. Available in the same materials and finishes asAccessAbility™ switches.

Wik-Scutcheons A WIKK EXCLUSIVE!

N6RF FLUSH MOUNTED73/4” Dia. X 21/8” H (197 X 54 mm) with trim ring 17/8” Inside Depth (48 mm)

Same material and qualities as N6RS, but designed formounting flush into hollow wall. Features a molded-in 7/8” (22 mm) wide trim ring and mounting bracket. Add N6WR gasket for weather-resistance.

Hard-Wire or Wireless if mountedinto RF-transparent wall materials.

6R Series Surface Mounts

6R Series switchesmount directly onto

1-gang prep of standard Wikk bollards.

(See page 2 and 4 for bollard details.)

See page 1 for switchcover materials, finishes,

and options.

13

Hard-Wire only

FEATURES:• Designed to flush-mount directly into

narrow jambs; no junction box needed• Compatible with a Jamb Surface Box (JSB)• Cutout and drill/tap template included• Requires custom bollard prep• Hard-Wire and Wireless

• See page 1 forswitch cover materials,finishes, and options.


AA SERIES SWITCHES (Narrow All-Active)Standard Satin Stainless Steel US32D (630)

PART NO. LEGEND(Debossed and Filled)

(Blue Infill)”PRESS”

(in Braille)

AA-1

AA-2

AA-3

AA-3 ALAA-3AR

AA-5

Blank – No Legend


(Blue Infill)


AA-5BRL

111/16” W x 41/2”H(43 x 114 mm)

PUSH TO OPENARROW LEFT

ARROW RIGHT(Blue Infills)

SHOWN WITH

SWITCH(Sold

Separately)

Part # JSB (Jamb Surface Box)

SURFACE MOUNT for Narrow Switches13/4” W X 49/16” H X 13/4” D (44 X 116 X 44 mm)15/8” Inside Depth (41 mm)• Narrow style box in sturdy black ABS • Micro-transmitter (SWTRAN M series) fits neatly into box• Self-adhesive mounting template included


Horizontal SwitchSpecifically designed for applications within narrow horizontal mullions or curtain wall framing. Flush-mount directly into mullions and framing.

• Cutout and drill/tap template included. • Compatible with Jamb Surface Box (JSB)• Requires Custom Bollard prep.• Hard-Wire and Wireless

Revolving Door SwitchDesigned to mount to the leading jamb of an automatic revolving door. When activated, the revolution speedslows to allow passage of slow-moving people.

• Raised Braille text reads the same. • Cutout and drill/tap template included. • Compatible with Jamb Surface Box (JSB).• Requires custom bollard prep• Hard-Wire and Wireless

Vestibule SwitchDesigned to independently operate 2 doors on opposite sides of a vestibule. Flushmounts to double gang electrical box with2-device surface ring and surface mountsto Wikk’s SURF SQ 4 & 6 BLK or SURF 4Mand BPS SM-DGANG prep.


Square Maintained Key Switchand AA-3 CombinationA combination switch featuring an AA and a maintained 1 pole key switch to offer a neat, orderly solution for access and security. The 41/2” x 41/2” back plate serves as the mounting plate, ready for flush mounting directly to a double gang electrical box with 2-device surface ring and surface mountsto Wikk’s SURF SQ 4 & 6 BLK or SURF 4M and BPS SM-DGANG prep.

• You may choose your AA legend and the finish to customize theinstallation.


Part #

KSM1-4xAA-3 US32D

Part # AA-PTSLOW

Braille

Part # AA-3AL x AA-3AR

Part # AA-3H

41/2” X 41/2” (144 X 144 mm)


NARRO

W &

STA

NDARD S

WITC

HES

SFA SERIES SWITCHES (Single Gang Full-Active)Standard Satin Stainless Steel US32D (630)

PART NO. LEGEND(Debossed and Filled)

SFA-1

SFA-2

SFA-3

SFA-5

Blank – No Legend


(Blue Infill)


23/4” W x 41/2” H (70 x 114mm)

FEATURES:• Fits all single gang (2 x 4) flush electrical boxes

• Use SURF SFA mount for surface or wireless applications

• Mount directly onto Wikk Square Bollards

• Hard-Wire and Wireless

• See page 1 for switch cover materials,finishes, and options.

SHOWN WITH

SWITCH(Sold

Separately)

SURFACE MOUNT for Single Gang SwitchesPart # SURF SFA23/4” W X 41/2” H X 15/8” D (70 X 114 X 41 mm)11/2” Inside Depth (38 mm)

Single-gang size brown phenolic box. Micro-transmitter (SWTRAN M series) fits neatly into mount.

Weather-resistant SFA requires SURF 4R box with adapter plate (see Page 11).


Paramount SwitchUpscale actuator switch with escutcheon plates becomes a fixture. The perfect design match for ornate buildings and historic renovations.

• Finishes available: US32D Satin Stainless (630)US32 Mirror Stainless (629)US4 Satin Brass (606-Uncoated)US3 Mirror Brass (605-Uncoated)US10B Dark Oxidized Satin Brass

oil-rubbed (613)

• Projects .625” (16 mm) from mounting surface.• Standard Legends and Custom available.• Hard-Wire

Paramount US32 (629)with Cuff

Paramount US10B (613)with Cuff

Part #

Paramount Switch US32D (630)

Projects 2 7/32” (56 mm) from mounting surface.

33/4” W x 51/2” H x 5/8” D (96 x 140 x 16 mm)

51/2” W x 71/4” H x 2 7/32” D (140 x 184 x 56 mm)

Paramount Switch with Cuff

NARROW & SINGLE GANG KEY SWITCHESStandard Satin Stainless Steel US32D (630)


SURFACE MOUNTfor Narrow

Key SwitchesPart #

JSB (Jamb Surface Box)13/4” W X 49/16” H X 13/4” D


• Narrow black ABS box accommodates wired or wireless operations

• Self-adhesive mounting template included


SINGLE GANG Key Switch 23/4” W x 41/2” H (70 x 114mm)

• Fits 1-Gang mount or prep • Mount directly onto Wikk square bollards

• Maintained contact• Access control where security is not a factor• Bi-colored LED indicates power ”ON” or ”HOLD-OPEN”

(available in green/amber, red/blue and green/red))• Key can be set in ”ON”, ”HOLD-OPEN” or ”OFF” position only• Key can be removed while in any operating mode

NARROW Key Switches 111/16” W x 41/2” H (43 x 114mm)

KSM1N OOH

PART NO. STYLEKS1N 1 pole, Momentary Contact

KS2N 2 pole, Momentary Contact

KSM1N 1 pole, Maintained Contact

KSM2N 2 pole, DPDT Maintained Contact

KSM1N OOH 1 pole, Maintained ContactOn/Off/Hold Open with Light

KSM1N OOH 2 pole, Maintained ContactOn/Off/Hold Open with Light

WIRELESS OPTION

KS-N

PUSH BUTTON SWITCHESSINGLE GANG Push Button Switches SPB Series

SPB-1BLK

SPB-5 RED

• Mounts to standard Single Gang Box • ”PUSH TO OPEN” self-adhesive label included • Choice of logo or no logo, red or black button• Not available as weather-resistant

NARROW Push Button Switches N/S Series• Mounts to JSB Box• ”PUSH TO OPEN” self-adhesive label included• Choice of logo or no logo, red or black button• Self-adhesive mounting cutout and drill/tap template included• Not available as weather-resistant

N/S-1BLK

N/S-5 RED

23/4” W x 41/2” H (70 x 114mm)

111/16”W x 41/2”H (43 x 114 mm)

KS-P

Mounting depths vary from 7/8” - 1-1/4” (22 x 32mm)depending on switch function and cover plate size

PART NO. STYLEKS1P 1 pole, Momentary Contact

KS2P 2 pole, Momentary Contact

KSM1P 1 pole, Maintained Contact

KSM2P 2 pole, Maintained Contact

KSM1P OOH 1 pole, Maintained ContactOn/Off/Hold Open with Light

KSM2P OOH 2 pole, Maintained ContactOn/Off/Hold Open with Light

WIRELESS OPTION

SURFACE MOUNTfor Single Gang

Key SwitchesPart # SURF 4R

23/4”W X 41/2”H X 111/16”D (70 X 114 X 41 mm)19/16” Inside Depth (40 mm)

Single gang brown phenolic box with corner-covering aluminum adapterplate to present a finished look.Micro-transmitter (SWTRAN-M series) fits neatly into mount.


SQUARE KEY SWITCHESStandard Satin Stainless Steel US32D (630)


KEY

& B

UTTO

N S

WITC

HES

FEATURES:• Heavy duty compact block and switch assembly

• 1” satin chrome mortise cylinder with standard Adams Rite cam and Schlage C keyways

• All locks keyed alike (Stainless switches only)

• Fully assembled with cylinder intact

• Complete parts kit includes: 2 keys, terminal connectors, stainless Phillips screws, stainless tamper-resistant screws, and set-screw wrench (for cylinder exchange)

• Rated 6 amps at 125 VAC, 3 amps at 250 VAC (1 PDT Momentary rated 5 amps at 120 VAC, 2 amps at 250 VAC)

OPTIONS:• Decorative materials and finishes (see page 1)

• Custom engraving upon request

• Wikk Wireless on single pole momentaryswitches (see pages 18-19 for transmitters)

• May be ordered without cylinder (Add suffix ”-CYL”)

• On/Off/Hold Open available without light (Add suffix ”-LIGHT”)

• Key Cylinder Adapter Plate for spacing of different sized cylinders.

Part # Key Cyl Adapter

SQUARE Key Switch

PART NO. STYLEKS1-4 1 pole,

Momentary Contact

KS2-4 2 pole, Momentary Contact

KSM1-4 1 pole, Maintained Contact

KSM2-4 2 pole, DPDT Maintained Contact

KSM1-4 OOH 1 pole, Maintained ContactOn/Off/Hold Open with Light

KSM2-4 OOH 2 pole, Maintained ContactOn/Off/Hold Open with Light

KS-4

41/2” x 41/2” (114 x 114 mm)

• Fits 1- or 2-gang mount or prep

• Mount directly onto Wikk squarebollards

• Includes dummy screws and nutsto present finished appearance

WIRELESS OPTION

SQUARE Maintained Key Switchand AA-3 Combination

PART NO. STYLE1 pole, Maintained Contact

KSM1-4xAA-3 with AA-3 Switch Attached (Other AA legends may be used)

KSM1-4XAA-3

A combination switch featuring an AA and a maintained 1 pole key switch tooffer a neat, orderly solution for accessand security. The 41/2” x 41/2” back-plateserves as the mounting plate, ready forflush mount directly to a double gangelectrical box with 2-device surface ring or surface mount to Wikk’s SURF 4/M,SURF SQ 4 & 6 BLK, and Square Bollards (requires 2-gang prep). You may choose your AA legend and the finish to customize the installation.

SHOWN WITHKSM1-4xAA-3 SWITCHAND BATTERY(Sold separately)

SURFACE MOUNTS for Square Key Switches

SURF SQ 4&6 BLK419/32”W X 419/32”H X 13/4”D (114 X 114 X 44 mm)


Black ABS box with unique battery change-out

compartment. Battery can be exchanged without

switch removal. Tamper resistant: compartment

door is held in place by the switch and cannot be removed or lost.

Switch mounting plate is recessed, presenting a finished appearance.



SURF 4/M4” X 4” X 11/8” O.D. (102 X 102 X 29 mm) 11/8” Inside Depth (29 mm)

Clear (628) or Dark Bronze (710) Anodized Aluminum ring with plated mounting bracket.

Hard-Wire only

N4X4F FLUSH MOUNT63/4” X 63/4” X 17/8” O.D. (172 X 172 X 47.6 mm) 5” X 5” Inside (127 X 127 mm)

17/8” Inside Depth (47.6 mm)

Hard-Wire or Wirelessif mounted into RF-transparent wall materials.

N4X4S SURFACE MOUNT51/2”W X 51/2”H X 17/8”D (140 X 140 X 54 mm) 5” X 5” Inside (127 X 127 mm)


Hard-Wire or Wireless

2 1/8” (54mm) projection. 4X4 switchsets flush within this durable ABS

enclosure, insuring a high degree oftamper-resistance. Includes a requiredweather-resistant gasket plate.

Durable black ABS enclosure, designed formounting flush into hollow wall. Features a

molded-in 7/8” (22mm) wide trim ring and aluminum mounting bracket. Includes a required weather-resistant gasket plate.


Add Remote Control Versatility with Wikk Wireless is a complete line of advanced radio control products.

Wikk Signature 433 Products are known for advanced rolling code technologies for high security application, improved range and longevity.

Wikk Wireless provides a variety of styles and frequencies to accommodate your requirements:

• Switch-operated • Hand-Held • Hands-Free • Key-Free

For Bollard use, tuck under rubber strap on Wikk standard black

bollard cap (non-metallic)

Transmitterssold

separately.

433MHz Hand-Held & Keychain TransmittersEach button operates one channel

• 4-button transmitters also available • Compatible with Wikk 433 Receivers

Part #

1TRANSM433213/32” W X 113/32” H X 1/2” D

(61 X 36 X 13 mm)

Includes Keychain

433MHz Receiver

433MHz Switch & Bollard Transmitter

433MHz Vestibule Sequencer

433MHz Personal Key-Free Transmitter

Part # Rec1Channel43311/4” W X 2” H X 3/4” D (32 X 51 X 19 mm)

Part #

SWTRAN 43319/64” W X 15/16” H X 7/32” D (29 X 49 X 6 mm)

not including wiring and battery

Part #

PKF 43323/8” W X 31/2” H X 11/16” D

(60 X 89 X 27 mm)

• Activated by light touch• Buzzer indicates

transmission• CR123A battery included• Indoor or outdoor use• Compatible with Wikk

433 Receivers

• 1 Channel

• Holds 85 Transmitter Codes

• 12-24 volt AC or DC

• Adjustable Time Hold

• Individually authorized codes for increased security

• Compatible with all Transmitters on this page

• Also available:Rec2Chan Ext 433 with 2 Relays

SIGNATURE 433MHz LINEProgrammable products are only compatible within Wikk products.

• Pre-wired for quick installation• One model fits all• Antenna magnifies signal• 9 Volt battery included• Compatible with Wikk 433 Receivers

Part # RECVESTSEQ 43341/8” W X 3/4” H X 11/8” D (105 X 44 X 29 mm)

Part #

1TRANSL43331/4” W X 17/8” H X 5/8” D

(83 X 48 X 16 mm)

Part #

2TRANSM433213/32” W X 113/32” H X 1/2” D

(61 X 36 X 13 mm)

Includes Keychain

Part #

2TRANSL43331/4” W X 17/8” H X 5/8” D

(83 X 48 X 16 mm)

Utilizing operator power, this receiver signals the second door – conserving transmitter battery power.

• Requires two receivers for two-way sequencing.

• Vestibule Sequencer compatible with all Transmitters on this page


WIR

ELESS

RFID Hands-Free Transmitter

COVER

Part # RFID 433 AUTOSIG2.75” W X 1.4” H X .35” D (70 X 36 X 9 mm)

• Automatic signaling• CR 2032 3 volt battery included• Compatible with RFID 433 Receivers

Part # RFID 433 1TRANS2.75” W X 1.4” H X .35” D (70 X 36 X 9 mm)

• Manual signaling• CR 2032 3 volt battery included• Compatible with RFID 433 Receivers

Dual Frequency and Power Compatibility• Handles 300/310MHz

(Multi-Code and Linear compatible)(Frequency recognition by jumper setting)

• Auto-sensing 12-24 Volts AC or DC

• 2 channel model: 10 DIP switches

Supplied with:• 9 pin connector and color-coded

wiring harness

• 9.5 inch (241 mm) 75 Ohm Whip Antenna

2 Channel Receiver

RFID 433MHz Receiver

Switch and Bollard Transmitter

RFID 433MHz

300MHzA unique battery-saving feature cuts off power after 10 seconds if switch is continually pressed.

Part #

1TRANSL3003.13” W X 1.75” H X .5” D

(80 X 45 X 13 mm)

Hand-Held & Keychain TransmittersEach button operates one channel.

Part #

REC2CHAN300/3103.6” W x 4.25” H x 1.5” D

(91 X 108 X 38 mm)

• 10 DIP switch models• Handles 300MHz (Multi-Code)• 9 Volt Battery included One Model Fits All Switches!

Wikk also supports 310MHz products - 8 DIP Switch Models

• 12 Volt Battery - Type 23A (Included) • 4-button transmitters also available

Part #

1TRANSM30011/2” W X 2” H X 1/2” D

(38 X 51 X 12 mm)

Part #

2TRANSL3003.13” W X 1.75” H X .5” D

(80 X 45 X 13 mm)

Part #

2TRANSM300 11/2” W X 2” H X 1/2” D

(38 X 51 X 12 mm)

Part#

SWTRAN300M13/8” W X 13/4” H X 1/8” D

(35 X 44 X 3 mm)

For Bollard use, tuck under rubber

strap on Wikk standardblack bollard cap

(non-metallic)

• Holds 30 codes• Individually authorized codes for increased security• Adjustable to range 3-50 ft.• Automatic shut-down after 4 seconds or no

motion of transmitter.

Receiver mounts adjacent to the door 45”-50”AFF (recommended) and is wired to the operator.

Part # RFID 433 REC WG3.5” W X 2.4” H X .9” D (89 X 61 X 23 mm)

• 26-bit Wiegand output

Part # RFID 433 REC 1D3.5” W X 2.4” H X .9” D (89 X 61 X 23 mm)

• For single door

NOTE: Do not place near metal

RECEIVER

• Integrates with any brand/model of access control system (WG model)

• Pocket/purse/bag model

• Ideal for clean rooms, operating rooms, assisted living centers, residential, or simply where the convenience or necessity of hands-free access control is preferred

RFID 4331TRANS

RFID 433AUTOSIG


CUSTOM DESIGNED SWITCHES

Wikk is well-known and respected for its custom design and manufacturing capabilitiesand timely shipping. Standard lead time is 2-3 weeks for Custom Switches.

We look forward to creating your special switch, whether it requires a distinctivefinish, logo, image, text, or simply a different infill color!

Don’t see your design here? Ask your local distributor about Wikk custom products.

Custom Wall Switches available: • Custom Design/Engraving and Braille • Special Materials and FinishesFinishes

• US32D Satin Stainless (630) • US32 Mirror Stainless (629) • US4 Satin Brass (606 uncoated)• US3 Mirror Brass (605 uncoated) • US10B Dark Oxidized Satin Brass oil-rubbed (613)

Wikk manufactures Grade 2 Braille as per ADA regulation.Please refer to your local codes for city and state compliance.


CUSTO

M D

ESIG

N a

nd TO

UCHLES

S S

WITC

HES

Alternate SWITCHING ACCESSORIESHEX WRENCHES These hex wrenches have an ergonomic 3-sided handle for a comfortable grip, and areused to install AccessAbility™ switches to junction boxes and surface mounts. One tool is included with every 20 switches ordered, and are also available for purchase.Part # PT-5/64 - (blue) used to mount switch to 1 & 2 gang

configurations using a 6-32 screw

Part # PT-3/32 - (white) used to mount 6”switches to 4x4 configurations using an 8-32 screw

SPANNER BIT for INGRESS’R®

This Spanner Bit is used to remove and install #8 security spanner bit screws on theINGRESS’R® switch located on the top of the INGRESS’R cap. One bit is included withthe purchase of 1-3 INGRESS’Rs. Additional bits are available for purchase.

Part # #8 SPANNER BIT

SEQUENCE & LOCK RELAYPart # SEQ. & LOCK RELAY

This device is used between the actuating switch and the door operator to create a momentary delay, allowing an electric strike or electric panic device to release before the door begins to open. Also can be used as a hard-wire vestibule sequencer.

13/4” L x 21/2” W x 1” H

ALTERNATE ACTION RELAYPart # ALT ACT'N RELAY

This device is an impulse relay used to change the normal momentary action of a wall switch to maintained, for ”Push to Open” and ”Push to Close” door operator activation. With 2 mounting brackets.

17/8” L x 15/8” W x 27/8” H

TOUCHLESS SWITCH

MISCELLANEOUS PRODUCTS

Installation TOOLS

No Touch Wave-to-Activate Switch For SanitaryEntry/Exit applications

• DPDT Dry Contact Output• No Moving Parts• Bi-color Status Illumination• Interior Application

Features & Applications• Uses IR Sensor technology; device is active with the

simple wave of a hand

• Designed to control electric locks/strikes, magnetic locks, or automatic door operators

• Ideal for use in sanitary applications such as cleanrooms, bathrooms, food processing, hospitals and labs.

• Sensing Range up to 4" (10cm)

• Mounted on a durable stainless steel plate

• Dual LED, illuminated sensor, Red/Green indicatesInactive/Active status

• Quick connect screwless terminal block for easy installation• Mounts to standard single gang electrical box

SpecificationsInput: 25mA (standby); 55mA (Active) @ 12/24VDCOutput: 2-SPDT, 3 Amp Dry ContactActivation Time: 1 second or as long as sensor is triggeredLED Color: Standby RED; Active GreenRange: 4" (10cm)Weight: 3 oz. (85g)Dimensions: 4.5" x 2.75" x 1.375" (115 x 70 x 35mm)Temperature Rated: - 4º F to 131º F

Part #

SFA NO TOUCH 32DPart #

4x4 NO TOUCH 32D

Side View FrontView

01 2014 Printed in U.S.A.

U.S. RepresentativesVisit the website: www.wikk.com/contactus.htmlto find a Representative in your area

Canadian Stocking DistributorsVisit the website: www.wikk.com/contactus.html

United Kingdom Stocking DistributorControls For Doors, LTD Hurst Place, Woldingham Rd. Woldingham, Surrey, England CR3 7AFwww.cfdltd.comMr. Kieran Lewis [email protected] Phone: 01.883.652652 • Fax: 01.883.652055

MEMBER OF:

Distributed by:

CORPORATE HEADQUARTERSLocal Phone: 414.421.9490 • Local Fax: 414.421.3158Toll Free: 877.421.9490 • Toll Free Fax: 877.421.3158

www.wikk.comP.O. Box 167 • 6169A Industrial Court

Greendale, WI 53129-0167

Bollard Solutions

Part #BPSSM OUTLETCLR

6” x 6” x 24” Tall, Clear Anodized Aluminum

(628),Surface mount, 1 prep for

electrical outletRemovable ABS cap

Part #BPD6 SM INR US32

6”RD x 42” Tall,304 Mirror Stainless Steel

US32 (629)Recessed area for flat devices,

Reveal (R) for a decorative touch,Welded Dome Top (D)

Part #BPS SM CLAD US10B

with I36-3 US10B6” x 6” x 42” Tall,

US10B Dark Oxidized SatinBrass, oil-rubbed (613),

Surface mount with concealedmounting base, 1 prep forINGRESS’R® ADA switch,

I36-3 US10B with gold logo, Removable Black ABS cap

Part #BPRTFSM126 PCCL12” x 6” x 54” Tall,

5 ga. Formed Mill Aluminum, Powder coated (PC) to match

Clear Aluminum,Surface mount with

concealed mounting base,3 preps for devices,

Welded Flat Top (FT)

Part # BPD6SMINR PCRED

6”Rd x42” Tall, Mill Aluminum, powder

coated (PC) in Red- RAL3020,Surface mount with concealed

mounting base, Recessed area for flat devices, 1/4” Reveals (R)

in two areas for a decorative touch,Welded Dome Top (D)

NEW

Part #BPR SM AINS PCDB6”RD x 48.625” Tall,

Mill Aluminum, powder coated (PC) to match

Dark Bronze AluminumSurface mount with concealed mounting base, Recessed area for ADA switch and card reader

on the angle top, Welded Angle Top (front slant) (AT)

Documents

AUTOMATIC DOOR ACTIVATION SOLUTIONS - Wikk Catalog.pdf · Wikk Bollard Options: For technical assistance, consult your local distributor or representative, visit wikk.com, or call