Embed Size (px)
Citation preview
Automatic Transfer Switch
Owner’s ManualATS “HS”Type
Models: 004635-3 (200 Amp, 250 Volts)
and 004678-2 (100 Amp, 250 Volts)
This manual should remain with the unit.
Generac Power Systems, Inc., hereafter referred to asthe “manufacturer”, cannot anticipate every possiblecircumstance that might involve a hazard. The warn-ings in this manual, and on tags and decals affixed tothe unit are, therefore, not all-inclusive. If using aprocedure, work method or operating technique themanufacturer does not specifically recommend,ensure that it is safe for others. Also make sure theprocedure, work method or operating technique cho-sen does not render the transfer switch unsafe.
Throughout this publication, and on tags and decals affixed to the generator, DANGER, WARNING,CAUTION and NOTE blocks are used to alert per-sonnel to special instructions about a particularoperation that may be hazardous if performed incor-rectly or carelessly. Observe them carefully. Their def-initions are as follows:
After this heading, read instructions that, if notstrictly complied with, will result in personalinjury, including death, or property damage.
After this heading, read instructions that, if notstrictly complied with, may result in personal injuryor property damage.
After this heading, read instructions that, if notstrictly complied with, could result in damage toequipment and/or property.
NOTE:After this heading, read explanatory statementsthat require special emphasis.
These safety warnings cannot eliminate the hazardsthat they indicate. Common sense and strict compli-ance with the special instructions while performing theservice are essential to preventing accidents.
Four commonly used safety symbols accompany theDANGER, WARNING and CAUTION blocks. The typeof information each indicates follows:
This symbol points out important safety informa-tion that, if not followed, could endanger personalsafety and/or property.
This symbol points out potential explosion hazard.
This symbol points out potential fire hazard.
This symbol points out potential electrical shockhazard.
GENERAL HAZARDS
• Any AC generator that is used for backup power ifa NORMAL (UTILITY) power source failure occurs,must be isolated from the NORMAL (UTILITY)power source by means of an approved transferswitch. Failure to properly isolate the NORMALand STANDBY power sources from each other mayresult in injury or death to electric utility workers,due to backfeed of electrical energy.
• Improper or unauthorized installation, operation,service or repair of the equipment is extremelydangerous and may result in death, serious per-sonal injury, or damage to equipment and/or per-sonal property.
• Extremely high and dangerous power voltages arepresent inside an installed transfer switch. Anycontact with high voltage terminals, contacts orwires will result in extremely hazardous, and pos-sibly LETHAL, electric shock. DO NOT WORK ONTHE TRANSFER SWITCH UNTIL ALL POWERVOLTAGE SUPPLIES TO THE SWITCH HAVEBEEN POSITIVELY TURNED OFF.
• Competent, qualified personnel should install,operate and service this equipment. Adhere strict-ly to local, state and national electrical and build-ing codes. When using this equipment, complywith regulations the National Electrical Code(NEC), CSA Standard; C22.1 Canadian ElectricCode and Occupational Safety and HealthAdministration (OSHA) have established.
• Never handle any kind of electrical device whilestanding in water, while barefoot, or while handsor feet are wet. DANGEROUS ELECTRICALSHOCK MAY RESULT.
!!
!
DANGER
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS! Read the following information carefully before attempting toinstall, operate or service this equipment. Also read the instructions and information on tags,decals, and labels that may be affixed to the transfer switch. Replace any decal or label thatis no longer legible.
DANGER! Connection of a generator to an electrical system normally supplied by an electricutility shall be by means of suitable transfer equipment so as to isolate the electric systemfrom utility distribution system when the generator is operating (Article 701 Legally RequiredStandby Systems or Article 702 Optional Standby Systems, as applicable). Failure to isolateelectric system by these means may result in damage to generator and may result in injuryor death to utility workers due to backfeed of electrical energy.
!
! !
!
Table of Contents
1
Safety Rules..........................................Inside Front CoverSection 1 — General Information ..................................21.1 Introduction ............................................................21.2 Equipment Description ............................................21.3 Transfer Switch Data Decal ......................................21.4 Transfer Switch Enclosure ......................................21.5 Safe Use Of Transfer Switch ....................................2
Section 2 — Installation ....................................................32.1 Introduction to Installation ......................................32.2 Unpacking ................................................................32.3 Mounting ..................................................................32.4 Connecting Power Source and Load Lines................3
2.4.1 2-Pole Mechanism ..........................................32.5 Connecting Start Circuit Wires ................................4
Section 3 — Operation ......................................................43.1 Functional Tests & Adjustments ..............................43.2 Manual Operation ....................................................4
3.2.1 Close to Normal Source Side ........................43.2.2 Close to Emergency Source Side....................53.2.3 Return to Normal Source Side ......................5
3.3 Voltage Checks..........................................................53.4 Generator Tests Under Load ....................................6
Section 4 – Notes................................................................7Section 5 – Installation Diagram..................................10Section 6 – Electrical Data ............................................11Section 7 – Exploded Views & Parts Lists ..................14Section 8 – Warranty/Service........................Back Cover
• Remove all jewelry (such as rings, watches,bracelets, etc.) before working on this equipment.
• If work must be done on this equipment whilestanding on metal or concrete, place insulativemats over a dry wood platform. Work on thisequipment only while standing on such insulativemats.
• Never work on this equipment while physically ormentally fatigued.
• Keep the transfer switch enclosure door closed andbolted at all times. Only qualified personnelshould be permitted access to the switch interior.
• In case of an accident caused by electric shock,immediately shut down the source of electricalpower. If this is not possible, attempt to free thevictim from the live conductor but AVOID DIRECTCONTACT WITH THE VICTIM. Use a nonconduct-ing implement, such as a dry rope or board, to freethe victim from the live conductor. If the victim isunconscious, apply first aid and get immediatemedical help.
• When an automatic transfer switch is installed fora standby generator set, the generator engine maycrank and start at any time without warning. Toavoid possible injury that might be caused by suchsudden start-ups, the system’s automatic start cir-cuit must be disabled before working on or aroundthe generator or transfer switch. Then place a “DONOT OPERATE” tag on the transfer switch and onthe generator. Remove the Negative (Neg) or (–) bat-tery cable.
For authorized service, reference the dealer locator
number found inside thegenerator owner’s manual.
2
Section 1 — General InformationATS “HS” Type Transfer Switch
1.1 INTRODUCTIONThis manual has been prepared especially for thepurpose of familiarizing personnel with the design,application, installation, operation and servicing ofthe applicable equipment. Read the manual carefullyand comply with all instructions. This will help toprevent accidents or damage to equipment that mightotherwise be caused by carelessness, incorrect appli-cation, or improper procedures.
Every effort has been expended to make sure that thecontents of this manual are both accurate and cur-rent. The manufacturer, however, reserves the rightto change, alter or otherwise improve the product atany time without prior notice.
1.2 EQUIPMENT DESCRIPTIONThe automatic transfer switch is used for transfer-ring electrical load from a UTILITY (NORMAL) powersource to a EMERGENCY ( STANDBY) power source.Such a transfer of electrical loads occurs automati-cally when the UTILITY power source has failed or issubstantially reduced and the EMERGENCY sourcevoltage and frequency have reached an acceptablelevel. The transfer switch prevents electrical feedbackbetween two different power sources (such as theUTILITY and EMERGENCY sources) and, for thatreason, codes require it in all standby electric systeminstallations.
The transfer switch consists of a transfer mecha-nism, a relay control, and a terminal strip for con-nection of sensing wires.
This switch is suitable for control of motors, electricdischarge lamps, tungsten filament and electric heat-ing equipment and the tungsten load does the switchrating.
The transfer switch is for use in optional standby sys-tems only.
The transfer switch is suitable for use on a circuitcapable of 10,000 rms symmetrical amperes, 240VAC when protected by a circuit breaker without anadjustable short time response or by fuses.
1.3 TRANSFER SWITCH DATA DECALA DATA DECAL is permanently affixed to the transferswitch enclosure. Use this transfer switch only withthe specific limits shown on the DATA DECAL and onother decals and labels that may be affixed to theswitch. This will prevent damage to equipment andproperty.
When requesting information or ordering parts for thisequipment, make sure to include all information fromthe DATA DECAL.
Record the Model and Serial numbers in the space pro-vided below for future reference.
1.4 TRANSFER SWITCH ENCLOSUREThe standard switch enclosure is a NationalElectrical Manufacturer’s Association (NEMA) 3Rtype. NEMA 3R type enclosures primarily provide adegree of protection against falling rain and sleet andis not damaged by the formation of ice on the enclosure.
1.5 SAFE USE OF TRANSFER SWITCHBefore installing, operating or servicing this equip-ment, read the SAFETY RULES (inside front cover)carefully. Comply strictly with all SAFETY RULES toprevent accidents and/or damage to the equipment.The manufacturer recommends that a copy of theSAFETY RULES are posted near the transfer switch.Also, be sure to read all instructions and informationfound on tags, labels and decals affixed to the equip-ment.
Two publications that outline the safe use of transferswitches are the following:
• NFPA 70; National Electrical Code• UL 1008, STANDARD FOR SAFETY-AUTOMATIC
TRANSFER SWITCHES
MODEL #
SERIAL #
3
2.1 INTRODUCTION TO INSTALLATIONThis equipment has been wired and tested at the fac-tory. Installing the switch includes the following pro-cedures:
• Mounting the enclosure.• Connecting power source and load leads.• Connecting the generator start circuit.• Connecting any auxiliary contact (if needed)• Testing functions.
2.2 UNPACKINGCarefully unpack the transfer switch. Inspect closelyfor any damage that might have occurred during ship-ment. The purchaser must file with the carrier anyclaims for loss or damage incurred while in transit.
Check that all packing material is completelyremoved from the switch prior to installation.
2.3 MOUNTINGMounting dimensions for the transfer switch enclo-sure are in this manual. Enclosures are typicallywall-mounted. See “Installation Diagram”, Section 5.
Handle transfer switches carefully wheninstalling. Do not drop the switch. Protect theswitch against impact at all times, and againstconstruction grit and metal chips. Neverinstall a transfer switch that has been dam-aged.
Install the transfer switch as close as possible to theelectrical loads that are to be connected to it. Mountthe switch vertically to a rigid supporting structure.To prevent switch distortion, level all mountingpoints. If necessary, use washers behind mountingholes to level the unit.
2.4 CONNECTING POWER SOURCEAND LOAD LINES
Make sure to turn OFF both the UTILITY(NORMAL) and EMERGENCY (STANDBY)power supplies before trying to connectpower source and load lines to the transferswitch. Supply voltages are extremely highand dangerous. Contact with such high volt-age power supply lines will result in anextremely hazardous, possibly lethal, electri-cal shock.
Wiring diagrams and electrical schematics are pro-vided in this manual. Power source and load connec-tions are made at a transfer mechanism, inside theswitch enclosure.
2.4.1 2-POLE MECHANISMThese switches (Figure 2.1) are used with a single-phase system, when the single-phase NEUTRAL lineis to be connected to a Neutral Lug and is not to beswitched.
Figure 2.1 — Typical 2-Pole Transfer Mechanism(200 Amp Shown)
Solderless, screw-type terminal lugs are standard.
Conductor sizes must be adequate to handle the max-imum current to which they will be subjected to,based on the 75°C column of tables, charts, etc. usedto size conductors. The installation must comply fullywith all applicable codes, standards and regulations.
Before connecting wiring cables to terminals, removeany surface oxides from the cable ends with a wirebrush. All power cables should enter the switch nextto transfer mechanism terminals. If ALUMINUM con-ductors are used, apply corrosion inhibitor to con-ductors. Tighten terminal lugs to the torque values asnoted on the decal located on the inside of the door.After tightening terminal lugs, carefully wipe awayany excess corrosion inhibitor.
All power cables should enter the switch next to thetransfer mechanism terminals.
Use a torque wrench to tighten the conduc-tors, being sure not to over tighten, or dam-age to the switch base could occur. If nottightened enough, a loose connection wouldresult, causing excess heat which could dam-age the switch base.
!
UTILITYCLOSINGCOIL
GENERATORCLOSINGCOIL
UTILITY LUGS
GENERATORLUGS (E1 & E2)
LOAD LUGS (T1 & T2)
DANGER
!
Section 2 — InstallationGTS “HS” Type Transfer Switch
Switch Wire Conductor TighteningRating Range Torque100A #14-1/0 AWG 50 in-lbs.200A #6-250 MCM 275 in-lbs.
4
Section 3 — OperationATS “HS” Type Transfer Switch
Connect power source load conductors to clearlymarked transfer mechanism terminal lugs as follows
1. Connect UTILITY (NORMAL) power source cablesto switch terminals N1, N2.
2. Connect EMERGENCY (STANDBY) source powercables to transfer switch terminals E1, E2.
3. Connect customer LOAD leads to switch termi-nals T1, T2.
Conductors must be properly supported, of approvedinsulative qualities, protected by approved conduit,and of the correct wire gauge size in accordance withapplicable codes.
Be sure to maintain proper electrical clearancebetween live metal parts and grounded metal. Allowat least 1/2 inch for 100-400 amp circuits.
2.5 CONNECTING START CIRCUITWIRES
Control system interconnections (Section 6) consistof UTILITY 1 (N1) and UTILITY 2 (N2), LOAD 1 (T1)and LOAD 2 (T2), and leads 23 and 194 when usedin conjunction with some water-cooled generators.Recommended wire gauge sizes for this wiringdepends on the length of the wire, as recommendedbelow:
NOTE:
If there are no matching terminal connections forLOAD 1 (T1) and LOAD 2 (T2) in the generatorcontrol panel, do not connect these wires. Failureof the control board will occur if connected.
3.1 FUNCTIONAL TESTS ANDADJUSTMENTS
Following transfer switch installation and inter-connection, inspect the entire installation careful-ly. A competent, qualified electrician shouldinspect it. The installation should comply strictlywith all applicable codes, standards, and regula-tions. When absolutely certain the installation isproper and correct, complete a functional test ofthe system.
Perform functional tests in the exact orderpresented in this manual, or damage could bedone to the switch.
IMPORTANT: Before proceeding with functionaltests, read and make sure all instructions and infor-mation in this section are understood. Also read theinformation and instructions of labels and decalsaffixed to the switch. Note any options or accessoriesthat might be installed and review their operation.
3.2 MANUAL OPERATION
Do NOT manually transfer under load.Disconnect transfer switch from all powersources by approved means, such as a maincircuit breaker(s).
A manual HANDLE is shipped with the transferswitch. Manual operation must be checked BEFOREthe transfer switch is operated electrically. To checkmanual operation, proceed as follows:
1. Turn the generator’s AUTO-OFF-MANUAL switchto OFF.
2. Turn OFF both UTILITY and EMERGENCYpower supplies to the transfer switch, with what-ever means provided (such as the main line cir-cuit breakers).
3. Note position of transfer mechanism main con-tacts by observing the moveable contact carrierarm.
• Manual operation handle towards the top ofswitch mechanism - LOAD terminals (T1, T2) areconnected to UTILITY terminals (N1, N2).
• Manual operation handle towards the bottom ofswitch mechanism - LOAD terminals (T1, T2) areconnected to EMERGENCY terminals (E1, E2).
Do not use excessive force when operatingthe transfer switch manually or damage couldbe done to the manual handle.
3.2.1 CLOSE TO NORMAL SOURCE SIDEBefore proceeding, verify the position of the switch byobserving the position of manual operation handle inFigure 3.1. If the handle is UP, the contacts are closedin the NORMAL position, no further action isrequired. If the handle is DOWN, proceed with Step1.
Step 1: With the handle inserted into the actuatingshaft, move handle UP. Be sure to hold on tothe handle as it will move quickly after thecenter of travel.
◆
!
!
DANGER
!
MAXIMUM WIRE LENGTH RECOMMENDED WIRESIZE
460 feet (140m) No. 18 AWG.461 to 730 feet (223m) No. 16 AWG.
731 to 1,160 feet (354m) No. 14 AWG.1,161 to 1,850 feet (565m) No. 12 AWG.
5
3.2.2 CLOSE TO EMERGENCY SOURCE SIDEBefore proceeding, verify the position of the switch byobserving the position of the manual operation han-dle in Figure 3.1. If the handle is DOWN, the contactsare closed in the EMERGENCY (STANDBY) position.No further action is required. If the handle is UP, pro-ceed with Step 1.
Step 1: With the handle inserted into the actuatingshaft, move the handle DOWN. Be sure tohold on to the handle as it will move quicklyafter the center of travel.
3.2.3 RETURN TO NORMAL SOURCE SIDEManually actuate switch to return manual operatinghandle to the UP position.
3.3 VOLTAGE CHECKS1. Turn ON the UTILITY power supply to the trans-
fer switch with whatever means provided (such asthe UTILITY main line circuit breaker).
PROCEED WITH CAUTION. THE TRANSFERSWITCH IS NOW ELECTRICALLY HOT. CONTACTWITH LIVE TERMINALS RESULTS IN EXTREMELYHAZARDOUS AND POSSIBLY FATAL ELECTRI-CAL SHOCK.
2. With an accurate AC voltmeter, check for correctvoltage.Single-phase utility supply:Measure across ATS terminal lugs N1 and N2.Also check N1 to NEUTRAL and N2 to NEUTRAL.
3. When certain that UTILITY supply voltage is cor-rect and compatible with transfer switch ratings,turn OFF the UTILITY supply to the transferswitch.
4. On the generator panel, set the AUTO-OFF-MANUAL switch to MANUAL position. The gener-ator should crank and start.
5. Let the generator stabilize and warm up at no-load for at least five minutes.
6. Set the generator's main circuit breaker (CB1) toits ON or CLOSED position.
DANGER
◆
◆
Section 3 — OperationATS “HS” Type Transfer Switch
Attach handle to actuating shaft.
Move handleUP for theNORMAL(UTILITY)position.
Move handleDOWN for theEMERGENCY(STANDBY)
position.
NOTE: Return handle tostorage position in enclosurewhen finished with manual transfer.
Figure 3.1 — Actuating Transfer Switch
6
PROCEED WITH CAUTION. GENERATOR OUT-PUT VOLTAGE IS NOW BEING DELIVERED TOTRANSFER SWITCH TERMINALS. CONTACTWITH LIVE TERMINALS RESULTS IN EXTREMELYDANGEROUS AND POSSIBLY FATAL ELECTRI-CAL SHOCK.
7. With an accurate AC voltmeter and frequencymeter, check the no-load, voltage and frequency.Single-phase generator supply:Measure across ATS terminal lugs E1 to E2. Alsocheck E1 to NEUTRAL and E2 to NEUTRAL.a. Frequency ......................................60-62 Hertzb. Terminals E1 to E2 ........................240-246 VACc. Terminals E1 to NEUTRAL ............120-123 VACd. Terminals E2 to NEUTRAL ............120-123 VAC
8. Set the generator’s main circuit breaker (CB1) toits OFF or OPEN position.
9. Set the AUTO/OFF/MANUAL switch to the OFFposition to shut down the generator.
NOTE:
Do NOT proceed until generator AC output voltageand frequency are correct and within stated limits.If the no-load voltage is correct but no-load fre-quency is incorrect, the engine governed speedprobably requires adjustment. If no-load frequen-cy is correct but voltage is not, the voltage regula-tor may require adjustment.
3.4 GENERATOR TESTS UNDER LOAD1. Set the generator's main circuit breaker to its
OFF or OPEN position.2. Manually actuate the transfer switch main con-
tacts to their EMERGENCY (STANDBY) position.Refer to Manual Operation (Section 3.2).
3. To start the generator, set the AUTO-OFF-MANUAL switch to MANUAL. When engine starts,let it stabilize for a few minutes.
4. Turn the generator's main circuit breaker to itsON or CLOSED position. The generator now pow-ers all LOAD circuits. Check generator operationunder load as follows:• Turn ON electrical loads to the full rated
wattage/amperage capacity of the generator.DO NOT OVERLOAD.
• With maximum rated load applied, checkvoltage and frequency across transfer switchterminals E1 and E2. Voltage should begreater than 230 volts and frequency shouldbe greater than 59 Hertz.
• Let the generator run under rated load for atleast 30 minutes. With unit running, listen forunusual noises, vibration, overheating, etc.,that might indicate a problem.
5. When checkout under load is complete, set maincircuit breaker of the generator to its OFF orOPEN position.
6. Let the generator run at no-load for several minutes. Then, shut down by setting the AUTO-OFF-MANUAL switch to its OFF position.
7. Move the switch's main contacts back to their UTILITY position. For example, load connected toUTILITY power supply. Refer to ManualOperation (Section 3.2). Handle and operatinglever of transfer switch should be in UP position.
8. Turn on the UTILITY power supply to transferswitch, using whatever means provided (such asa UTILITY main line circuit breaker). The UTILI-TY power source now powers the loads.
9. Set the generator's AUTO-OFF-MANUAL switch toits AUTO position. The system is now set for fullyautomatic operation.
DANGER
Section 3 — OperationATS “HS” Type Transfer Switch
7
Section 4 — NotesATS “HS” Type Transfer Switch
8
Section 4 — NotesATS “HS” Type Transfer Switch
9
Section 4 — NotesATS “HS” Type Transfer Switch
Section 5 — Installation DiagramATS “HS” Type Transfer Switch
Drawing No. 0E7081
377m
m[1
4.84
"]
508.
5mm
[20.
02"]
KN
OC
KO
UT
SU
ITA
BLE
FO
R1"
, 1-1
/2"
AN
D 2
" C
ON
DU
IT S
IZE
3 P
LAC
ES
179.
5mm
[7.0
7"]
420m
m[1
6.54
"]
45m
m[1
.77"
]
41.5
mm
[1.6
3"]
294m
m[1
1.57
"] Ø6.
3mm
[Ø0.
25"]
10
11
- OPE
N S
WIT
CH
TO
TES
T -
2A @
250
Vac
MIN
.
SWIT
CH
TYP
E, S
PST
ELEC
TRIC
AL R
ATIN
GS,
NO
TE:
IF T
HER
E AR
E N
O M
ATC
HIN
G T
ERM
INAL
CO
NN
ECTI
ON
S FO
R L
OAD
1 (T
1) A
ND
LOAD
2 (T
2) IN
TH
E G
ENER
ATO
R C
ON
TRO
L PA
NEL
DO
NO
T C
ON
NEC
T TH
ESE
WIR
ES, F
AILU
RE
OF
THE
CO
NTR
OL
BOAR
D W
ILL
OC
CU
R IF
CO
NN
ECTE
D.
UTI
LITY
1 (N
1)
UTI
LITY
2 (N
2)
LOAD
2 (T
2)
23 194
CB1
NEU
TRAL
CO
NN
ECTI
ON
N1
N2
T1T22T
E1E22E
NEU
TRAL
LUG
TRAN
SFER
SWIT
CH
UTI
LITY
SU
PPLY
WIT
HSE
RVI
CE
DIS
CO
NN
ECT
LOAD
CU
STO
MER
194
23
LOAD 2
UTILITY 2
UTILITY 1
AC G
ENER
ATO
RC
ON
TRO
L PA
NEL
NO
TE:
POW
ER L
EAD
S AN
D
TRAN
SFER
SW
ITC
HLE
ADS
MU
ST B
ER
UN
IN T
WO
D
IFFE
REN
T C
ON
DU
ITS.
LOAD
1 (T
1)
22
LOAD 1
REM
OTE
TES
TSW
ITC
H (O
PTIO
NAL
)
11 44
33
Section 6 — Electrical DataATS “HS” Type Transfer Switch
Transfer Switch Interconnections - Drawing No. 074106-B
12
Section 6 — Electrical DataATS “HS” Type Transfer Switch
Electrical Schematic - Drawing No. 0E6093-B
13
Section 6 — Electrical DataATS “HS” Type Transfer Switch
Electrical Schematic - Drawing No. 0E6093-B
14
6
9
8
16
37
21
73
23 15
24
4
36
2194
2528
NEU
TRAL
2917
18 1314 11 13
40 2619
10
20
22
3231
355
30
3933
34
121
32
4
30A,
600V
30A,
600
V07
3591
-T07
3591
T30
A,60
0V30
A, 6
00V
0735
91-T
0735
91T
30A,
600V
30A,
600
V07
3591
-T07
3591
T30
A,60
0V30
A, 6
00V
0735
91-T
0735
91T
ENC
LOSU
RE
(GR
OU
ND
LU
G A
SSEM
BLY)
(PO
WER
TER
MIN
AL L
UG
ASS
EMBL
Y)N
OTE
: TO
RQ
UE
ITEM
#3
TO 2
4-30
IN.L
BS
DET
AIL
B-B
A A
BB
0A95
17
WAU
KESH
A, W
I.
OR
ALU
MIN
UM
WIR
E O
F AT
LEA
ST 7
5°C
RAT
ING
RAT
ING
SWIT
CH
GEN
ERAC
PO
WER
SYS
TEM
S, IN
C.
120/
240
CS3
-8X1
6TC
S38X
16T
8X16
T
***
(C2
& VR
2)ST
AND
BY
0C22
37fv
****
*
****
****
*
****
*
**
Section 7 — Exploded Views and Parts ListATS “HS” Type Transfer Switch
100A Transfer Switch Assembly – Drawing No. 0E8403$-F
15
ITEM PART NO. QTY. DESCRIPTION
1 0C2237 1 TR SW-HSB 100A 2P 250V2 077033 6 LUG SLDLSS 1/0-#14X9/16 AL/CU3 036932 6 SCREW PPHM #10-32 X 1/44 022152 6 WASHER LOCK #105 074908 4 SCREW HHTT M5-0.8 X 10 BP6 045771 1 NUT HEX M8-1.25 G8 YEL CHR7 062684 1 LUG SLDLSS 2/0-#12 X 11/32 CU8 0C3168 1 WASHER LOCK SPECIAL 5/169 022129 1 WASHER LOCK M8-5/16
10 073590A 4 FUSE 5A X BUSS11 073591 4 FUSE HOLDER12 090388 2 SCREW HHTT M6-1.0 X 12 ZINC13 0A1495 6 SCREW HHTT M4-0.7 X 10 BP14 063617 1 RELAY PNL 12VDC DPDT 10A@240VA15 0C2454 2 SCREW TH-FRM M6-1 X 16 N WA Z/JS16 0A1661 2 RIVET POP .156 X .675 AL17 0C4449 1 ASSY NEUTRAL BLOCK 100A18 0E6057 1 WELDMENT XFER SW BOX HSB19 0E6056 1 COVER TRANSFER SWITCH BOX HSB
20**** 0F0668 1 DECAL TRANSFER SWITCH21 0A2595 1 DECAL TERMINAL STRIP22 0E8443 1 DECAL SWITCH RATING
23*** 095282 1 DECAL-LIVE CIRCUIT24 067210A 1 DECAL GROUND LUG25 0A9457 1 DECAL NEUTRAL26 0A9517 1 DECAL MANUAL 5A FUSE
27* 077036D 1 DECAL TEST SEQUENCE 3R28 081221 1 DECAL-UL LIST HSB29 064101 4 NUT HEX FL WHIZ 3/8-1630 0E6055 1 SUBPLT TRANSFER SWITCH HSB
31***** 063378 4 HOLDER CABLE TIE32***** 028739 4 TIE WRAP UL 3.9" X .10" NATL
33 0E6193 1 BRACKET, ARM EXTENDER34** 0E6155 0 ARM EXTENDER PIN
35 0E6303 1 WIRE A36 0E6303A 1 WIRE B37 0E6303C 1 WIRE E138 0E6094 1 WIRE HARNESS 100/200A 2P HS (NOT SHOWN)39 064526 2 SCREW HWHS #6-25 X 3/8 ZNC40 0F2088 1 DECAL TRANSFER SWITCH DATA 100
* CENTER DECAL ON INSIDE OF THE COVER (ITEM #19)** SUPPLIED WITH TRANSFER SWITCH ITEM #1.*** PLACE DECAL ON OUTSIDE OF COVER, LOWER RIGHT CORNER.**** NOT SHOWN ON THIS ASSEMBLY, CENTER DECAL ON FRONT OF COVER, 7" FROM TOP OF ENCLOSURE.***** SUPPLIED WITH HARNESS (P/N 0E6094).
Section 7 — Exploded Views and Parts ListATS “HS” Type Transfer Switch
100A Transfer Switch Assembly – Drawing No. 0E8403$-F
NEU
T
30
8
6
9
2019
7
152231
13 21161110
PT/NO A259555
LOAD 2
LOAD 1
UTILITY 2
UTILITY 1
194
23
4129
42
A
C
A
A
A
26
23 2814 1318
A
2740
35
33
24
A
12 1738 3436
3
A525
2 1
4
0573
29-S
ENC
LOSU
RE
(GR
OU
ND
LU
G A
SSEM
BLY)
DET
AIL
A-A
3 TO
72±
1 IN
-LBS
NO
TE: T
OR
QU
E IT
EM
CS
C CS3
-8X1
6T8X
16
CS3
-8X1
6TC
8X16
22097 S
WS34X14S
0A95
17
SYST
EM V
OLT
AGE
120/
240
SER
IAL
NU
MBE
R
***
****
*
6337
8T
6337
8-T
****
****
*
****
*
**
16
Section 7 — Exploded Views and Parts ListATS “HS” Type Transfer Switch
200A Transfer Switch Assembly – Drawing No. 0E5782$-J
17
Section 7 — Exploded Views and Parts ListATS “HS” Type Transfer Switch
200A Transfer Switch Assembly – Drawing No. 0E5782$-J
ITEM PART NO. QTY. DESCRIPTION
1 0D9618 1 TR SW-HSB 200A 2P 250V2 0E3375 6 LUG SLDLSS 250-#6 AL/CU3 0F1252 6 SCREW BHSC 1/4-20 X 3/84 022097 6 WASHER LOCK M6-1/45 066849 5 SCREW HHTT M5-0.8 X 16 BP6 045771 1 NUT HEX M8-1.25 G8 YEL CHR7 057329 1 LUG SLDLSS 350-#6 X 13/32 AL/CU8 027482 1 WASHER SHAKEPROOF EXT 5/16 STL9 022129 1 WASHER LOCK M8-5/16
10 073590A 4 FUSE 5A X BUSS11***** 073591 4 FUSE HOLDER
12 090388 2 SCREW HHTT M6-1.0 X 12 ZINC13 0A1495 6 SCREW HHTT M4-0.7 X 10 BP
14***** 063617 1 RELAY PNL 12VDC DPDT 10A@240VA15 0C2454 2 SCREW TH-FRM M6-1 X 16 N WA Z/JS16 0A1661 2 RIVET POP .156 X .675 AL17 0C4449A 1 ASS'Y-NTRL BL150-200A18 0E6057 1 WELDMENT XFER SW BOX HSB19 0E6056 1 COVER TRANSFER SWITCH BOX HSB
20**** 0F0668 1 DECAL TRANSFER SWITCH21 0A2595 1 DECAL TERMINAL STRIP
22*** 095282 1 DECAL-LIVE CIRCUIT23 0E8443 1 DECAL SWITCH RATING24 064101 4 NUT LOCK FL 3/8-1625 0E6055 1 SUBPLT TRANSFER SWITCH HSB
26***** 063378 5 HOLDER CABLE TIE27***** 028739 5 TIE WRAP UL 3.9" X .10" NATL
28 0F2516 1 DECAL TRANSFER SWITCH DATA 20029 067210A 1 DECAL GROUND LUG30 0A9457 1 DECAL NEUTRAL31 0A9517 1 DECAL MANUAL 5A FUSE
32 * 0E6190 1 DECAL TEST SEQUENCE 2P TS 3R33 081221 1 DECAL-UL LIST HSB34 0E6193 1 BRACKET ARM EXTENDER35 064526 2 SCREW HWHS #6-25 X 3/8 ZNC
36 ** 0E6155 1 ARM EXTENDER PIN37 0E6094 1 HARN 100/200A 2P HS
38 ** 0E6033 2 90 DEGREE DN SPADE CONNECTOR40 0E6303 1 WIRE A41 0E6303A 1 WIRE B42 0E6303B 1 WIRE-E1
* CENTER DECAL ON INSIDE OF THE COVER (ITEM #19)** SUPPLIED WITH TRANSFER SWITCH ITEM #1.*** PLACE DECAL ON OUTSIDE OF COVER, LOWER RIGHT CORNER.**** NOT SHOWN ON THIS ASSEMBLY, CENTER DECAL ON FRONT OF COVER, 7" FROM TOP OF ENCLOSURE.***** SUPPLIED WITH HARNESS (P/N 0E6094)
Part No. 0E6347 Revision H (02/09/05) Printed in U.S.A.
Section 8 — WarrantyATS “HS” Type Transfer Switch
GENERAC POWER SYSTEMS, INC. WARRANTY/SERVICE
Generac Power Systems, Inc. will warrant from the date of purchase that our transferswitch will be free from defects in material and workmanship for the items and periods setforth in the warranty statement found in the owners manual of the Generac Power SystemsInc. generator that this transfer switch will be utilized with.
Any equipment that the purchaser/owner claims to be defective must be examined by thenearest Generac Authorized Warranty Service Dealer which may be found by visiting ourwebsite at www.generac.com or by calling the dealer locator number at 1-800-333-1322.Select the prompt that describes the brand name of the generator.
THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,SPECIFICALLY, GENERAC MAKES NO OTHER WARRANTIES AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Some states do not allow limitations on how long an implied warranty lasts, so the abovelimitation may not apply to you.
GENERAC’S ONLY LIABILITY SHALL BE THE REPAIR OR REPLACEMENT OF PART(S)AS STATED ABOVE. IN NO EVENT SHALL GENERAC POWER SYSTEMS, INC. BELIABLE FOR ANY INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF GENERAC’S NEGLIGENCE.Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.
This warranty gives you specific legal rights. You also may have other rights that vary fromstate to state.
GENERAC® POWER SYSTEMS, INC.
P.O. BOX 297 • WHITEWATER, WI 53190
