Upload
others
View
224
Download
3
Embed Size (px)
Citation preview
Axial Flow Fans
Section 4
Axial Fan
s - Section
4
Fläkt Woods offers a wide range of axial flow fans for
general air movement and special applications such
as emergency high temperature smoke extract and
pressurisation. ATEX fans for explosive atmospheres and
multistage options for increased pressure development.
All fans are tested to the latest internationally recognised
standard IS05801 Part 1 (1997), installation category D
(AMCA approved) for aerodynamic performance and
BS848 Part 2 (1985) for acoustic performance. Coupled
with the above fan diameters, the adjustable pitch
Aerofoil impeller gives the exact performance required,
with a non overloading fan characteristic.
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
Sizes
31JM - (315mm) to 100JM - (1000mm).Larger sizes up to 2800mm diameter are also available. Please enquire.
Fan Performance
All fans are tested to the latest internationally recognised standard IS05801 Part 1 (1997), installation category D (AMCA approved) for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance.Coupled with a wide range of fan diameters, the adjustable pitch Aerofoil impeller gives the exact performancerequired, with a non overloading fan characteristic.
Impellers
A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustablepitch angle availability.The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise.Every cast aluminium component is X-ray examined using Real Time Radiography inspection prior to assembly.The maximum pitch angles shown allow for speed control by frequency inverter (3ph only).
Motors
All motors are totally enclosed air stream rated class F insulation. Constructed from aluminium or cast iron as standard with special ‘T’ slot or pad mounted fixings. Single speed motors are suitable for speed control by voltage regulation where indicated. Three phase motors are suitable for use with frequency inverters.Two speed motors where available are pole change type.Suitable for horizontal through to vertical shaft operation. Supplied IP55, with removable drain plugs. Sealed for life bearings lubricated with wide temperature range grease. The BT, CT, F22 and PM112 motors are all fitted with overheat protection thermostat as standard. D motors are fitted with Thermistor OHP.These motors are suitable for inverter speed control down to 20% of full speed.
Electrical Supply
220 - 240 V / 50 Hz / 1 φ380 - 420 V / 50 Hz / 3 φ
Temperature Range
-40°C to 50°C as standard. (All motors are not suitable for starting at temperatures lower than -20°C.) Fans thatinclude BT or CT motors can be continuously operated at temperatures up to 70°C. When these fans are operatingin excess of 50°C they should be run at full speed only. Other fans can be operated up to 70°C with appropriatederation of motors.Most standard 3φ fans can be offered for a one off emergency operation at 200˚C for 2 hours.
Casings
JM Aerofoil fans are available in either a long cased form, complete with an externally mounted pre-wiredelectrical terminal box, or short cased for duct or plate installation. Casings are spun from sheet steel with integralpre-drilled and radiused inlet flanges. The galvanised finish gives a high resistance to corrosion and is ideal forexternal as well as internal use.
Accessories
Silencers, Mounting feet, Vibration isolators, Matching flanges, Flexible connectors, Air operated non return dampers, Guards, Bell mouth inlets. Electronic and transformer type speed controllers and frequency inverters.
• Eleven sizes are offered from 315mm to 1000mm diameter.
• Volume flows of up to 19m3/s• Static pressures up to 800 Pa• High energy efficiency
• Low installed noise levels• Motor protection IP55• All casings are hot dipped galvanised• Overheat protection is fitted as standard • Inverter controllable
74
Aerofoil - JM Aerofoil Section 4
Section
4 - A
erofoil - JM A
erofoil
Standards available contact your local ExpressDistributor for more details. See section 4.3.
Summary JM Aerofoil Data Section 4
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
75
Dia. Product Product Speed Sound Electronic m3/s at Pa (Static)
mm Code Number rev/min Level Speed
dBA Controller 0 50 100 150 200 250 300 400 500
315 31JM/16/4/5/38 DX321460 1420 44 ME1.1 0.65 0.54
315 31JM/16/2/5/32 DX321202 2840 61 N/A 1.15 1.11 1.06 0.99 0.94 0.86 0.78 0.59
355 35JM/16/4/5/40 DX361460 1420 49 ME1.1 1.00 0.86 0.63
355 35JM/16/2/5/34 JL361205 2840 64 N/A 1.73 1.70 1.63 1.56 1.45 1.40 1.31 1.12
400 40JM/16/4/5/40 DX411452 1420 52 ME1.3 1.50 1.31 1.06
400 40JM/16/2/5/28 JL411203 2840 66 N/A 2.33 2.26 2.19 2.11 2.05 1.97 1.72 1.67 1.42
450 45JM/16/4/5/30 JL461452 1420 57 ME1.3 1.80 1.61 1.40 1.11
450 45JM/16/4/5/40 DX461466 1420 56 ME1.3 2.20 1.95 1.72
450 45JM/16/2/5/18 JL461201 2840 66 N/A 2.50 2.45 2.40 2.30 2.20 2.10 2.05 1.85 1.6
500 50JM/16/4/5/34 DX511464 1420 57 ME1.6 2.75 2.50 2.21 1.85
500 50JM/16/4/5/40 JL511460 1420 59 ME1.6 3.00 2.75 2.43
500 50JM/20/4/6/20 DX511455 1420 53 ME1.3 1.85 1.70 1.50 1.25
500 50JM/20/4/6/32 DX511466 1420 56 ME1.6 2.60 2.41 2.20 1.95 1.60
560 56JM/16/4/5/22 JL571453 1420 57 ME1.6 2.90 2.70 2.35 2.10 1.65
560 56JM/16/4/5/28 DX571456 1420 58 ME1.6 3.40 3.15 2.85 2.55 2.10
630 63JM/20/4/6/16 DX641453 1420 61 ME1.6 3.45 3.30 3.10 2.90 2.65 2.25
220 - 240 V / 50 Hz / 1φ
Quick selection guide to the JM Cased Aerofoil fans available
Express Range - These products are available from our UK Express Distributor on same day deliveryfrom the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
Full selection details and dimensions see section 4.1 or 9.1 (which covers all accessories)
Summary JM Aerofoil Data Section 4
Section
4 - A
erofoil - JM A
erofoil
76
Dia. Product Product Speed Sound Electronic m3/s at Pa (Static)
mm Code Number rev/min Level Speed Inverter
dBA Controller 0 50 100 150 200 250 300 400 500 600 800
315 31JM/16/4/5/40 DX341460 1420 44 ME3.5S FWD1 0.67 0.55
315 31JM/16/2/5/36 DX341202 2840 61 N/A FWD1 1.25 1.18 1.15 1.06 1.01 0.93 0.85
355 35JM/16/4/5/40 DX381460 1420 49 ME3.5S FWD1 1.00 0.86 0.63
355 35JM/16/2/5/34 DX381210 2840 64 N/A FWD1 1.73 1.70 1.63 1.56 1.45 1.40 1.31 1.12
355 35JM/16/2/5/40 JL381204 2840 66 N/A N/A 2.00 1.93 1.90 1.82 1.73 1.65 1.55 1.27
400 40JM/16/4/5/40 DX431452 1420 52 ME3.2D FWD1 1.50 1.31 1.06
400 40JM/16/2/5/32 DX431203 2840 66 N/A FWD2 2.60 2.51 2.42 2.35 2.27 2.18 2.08 1.86 1.61
450 45JM/16/4/5/30 JL481452 1420 52 ME3.2D N/A 1.80 1.61 1.40 1.11
450 45JM/16/4/5/40 DX481460 1420 56 ME3.2D FWD1 2.20 1.95 1.72
450 45JM/16/2/5/20 JL481202 2840 66 N/A N/A 2.65 2.60 2.54 2.48 2.40 2.31 2.20 2.02 1.80
450 45JM/20/2/6/34 EX481205 2910 72 N/A FWD4 3.85 3.80 3.70 3.60 3.52 3.40 3.31 3.12 2.90 2.70
500 50JM/16/4/5/34 DX531460 1420 57 ME3.2D FWD1 2.75 2.50 2.21 1.85
500 50JM/16/4/5/40 JL531454 1420 59 ME3.2D N/A 3.00 2.75 2.43
500 50JM/20/4/6/20 JL531456 1420 53 ME3.2D N/A 1.85 1.70 1.50 1.25
500 50JM/20/4/6/32 DX531462 1420 56 ME3.2D FWD1 2.60 2.41 2.20 1.95 1.60
500 50JM/20/4/6/40 JL531458 1420 58 ME3.2D N/A 2.97 2.77 2.51 2.20
500 50JM/20/2/6/24 EX531203 2840 70 N/A FWD4 4.30 4.22 4.18 4.05 4.00 3.90 3.80 3.62 3.42 3.22 2.60
500 50JM/20/2/6/34 DX531204 2840 74 N/A FWD6 5.52 5.48 5.35 5.27 5.20 5.09 4.92 4.75 4.45 4.22 3.60
560 56JM/16/4/5/24 JL591452 1420 57 ME3.2D N/A 3.05 2.82 2.55 2.22 1.82
560 56JM/16/4/5/32 DX591453 1420 58 ME3.2D FWD1 3.73 3.42 3.23 2.80 2.38
560 56JM/20/4/6/36 DX591458 1420 61 ME3.2D FWD2 4.05 3.82 3.60 3.21 2.90
560 56JM/20/2/6/24 EX591201 2910 73 N/A FWD6 6.30 6.20 6.10 6.05 5.90 5.85 5.70 5.46 5.20 5.08 4.35
630 63JM/20/6/6/22 JL661651 900 49 ME3.2D N/A 2.51 2.20 1.75
630 63JM/20/6/6/34 JL661652 900 50 ME3.2D N/A 3.55 3.10 2.50
630 63JM/20/4/6/22 DX661453 1420 61 ME3.2D FWD2 4.05 3.8 3.6 3.4 3.1 2.85
630 63JM/20/4/6/32 DX661454 1420 61 AT7.0 FWD2 5.30 5.10 4.81 4.55 4.15 3.82
710 71JM/20/6/6/22 JL741652 900 53 ME3.2D FWD1 3.75 3.55 3.00
710 71JM/20/6/6/36 EX741653 900 55 N/A FWD2 5.55 4.90 4.20
710 71JM/20/4/6/20 DX741404 1440 64 N/A FWD5 6.1 5.8 5.6 5.4 5.2 4.8 4.5
710 71JM/20/4/6/24 EX741401 1440 65 N/A FWD3 6.45 6.20 6.00 5.75 5.50 5.22 4.87
800 80JM/20/6/6/28 EX831651 935 58 N/A FWD2 6.60 5.70 5.20 4.50
800 80JM/20/6/6/36 JL831603 935 60 N/A FWD3 7.90 7.25 6.50 5.60
800 80JM/20/4/6/24 JL831412 1440 69 N/A FWD5 9.41 9.00 8.51 8.18 7.82 7.40 6.90
800 80JM/25/4/9/22 EX831405 1440 71 N/A FWD5 8.50 8.10 7.90 7.60 7.40 7.00 6.60 6.00
800 80JM/25/4/9/26 EX831408 1440 71 N/A FWD6 9.50 9.25 9.00 8.70 8.40 8.05 7.60 6.90
900 90JM/25/8/9/34 JL931802 695 58 N/A FWD2 8.20 7.32 6.25
900 90JM/25/6/6/32 EX933652 935 65 N/A FWD2 9.60 9.00 8.15 7.10
900 90JM/25/6/9/24 JL931602 935 63 N/A FWD3 8.50 8.05 7.55 7.05 6.55 5.70
900 90JM/25/4/9/22 EX931403 1440 74 N/A FWD7 12.50 12.10 12.00 11.50 11.10 10.70 10.40 10.00 8.90
900 90JM/25/4/9/30 EX931406 1440 75 N/A FWD8 16.20 15.20 14.80 14.40 14.00 13.70 13.30 12.40 11.80
1000 100JM/25/8/9/24 JL131802 695 61 N/A FWD2 8.80 7.90 6.70
1000 100JM/25/6/6/22 EX133652 950 68 N/A FWD3 10.80 9.90 8.10 6.90
1000 100JM/25/6/9/34 JL131609 960 71 N/A FWD6 15.40 14.60 14.00 13.00 12.00 10.80
1000 100JM/25/4/6/22 EX133402 1470 79 N/A FWD7 16.20 15.90 15.20 14.70 14.10 13.80 13.10 11.70 10.00
1000 100JM/25/4/9/20 JL131419 1470 79 N/A FWD8 16.50 16.00 15.50 15.10 14.90 14.30 13.90 12.80 11.60
1000 100JM/25/4/9/24 EX131405 1470 79 N/A FWD9 18.80 18.28 17.75 17.48 17.20 16.30 15.40 14.50 13.60
380 - 420 V / 50 Hz / 3φ
Full selection details and dimensions see section 4.1.
Aerofoil fan 31JM - 35JM Section 4.1
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
77
4 Pole
31JM/16/4/5/... 35JM/16/4/5/...
2 Pole
31JM/16/2/5/... 35JM/16/2/5/...
Electrical Data
† BT4 - 3φ
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.When these fans are operating in excess of 50°C they should be run at full speed only.
For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.Product numbers shown are for Long cased fans.
Wiring diagram references can be found in section 9.2.
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA
31JM/16/4/5/40 1420 BT5/4 DX341460 34-40 0.13 0.47 1.8 CD1344 ME3.5S MT3.0.5 FWD1 44
31JM/16/2/5/34 2840 BT9 DX341202 8-34 0.58 1.4 6 CD1344 N/A N/A FWD1 61
35JM/16/4/5/40 1420 BT4 DX381460 22-40 0.13 0.47 1.8 CD1344 ME3.5S MT3.0.5 FWD1 49
35JM/16/2/5/34 2840 CT5 DX381210 8-34 0.95 2 9.5 CD1344 N/A N/A FWD1 64
35JM/16/2/5/40 2840 CT9 JL381204 36-40 1.7 3.7 19 CD1344 N/A N/A N/A 66
220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
31JM/16/4/5/40 1420 BT5/4† DX321460 24-38 0.12 0.9 1.8 CD1705 ME1.1 MT1.1 44
31JM/16/2/5/34 2840 BT9 DX321202 26-30 0.5 3.3 9 CD1705 N/A N/A 61
35JM/16/4/5/40 1420 BT4 DX361460 28-40 0.13 1 2 CD1705 ME1.1 MT1.1 49
35JM/16/2/5/34 2840 CT5 JL361205 32-34 1.0 5.9 11.5 CD1705 N/A N/A 64
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400
31JM/16/4/5/40 1420 0.67 0.55
31JM/16/2/5/34 2840 1.25 1.18 1.15 1.06 1.01 0.93 0.85
35JM/16/4/5/40 1420 1.00 0.86 0.63
35JM/16/2/5/34 2840 1.73 1.70 1.63 1.56 1.56 1.40 1.31 1.12
35JM/16/2/5/40 2840 2.00 1.93 1.9 1.82 1.73 1.65 1.55 1.27
Aerofoil fan 31JM - 35JM Section 4.1
Section
4 - A
erofoil - JM A
erofoil
78
Dimensions
All dimensions shown in mm.
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which covers all accessories)
Long Cased
Short Cased
Product Motor A B C D E F G H J K L M N P S T U X Max. Fan
Code Range Weight (kg)
Long Cased
31JM BT4/5 315 395 330 235 2.0 25 175 355 66 245 265 315 10 200 8 10 - 0.8 23
31JM BT9 315 395 375 235 2.5 25 175 355 66 289 265 315 10 200 8 10 - 0.8 27
35JM BT4/CT5 355 435 330 256 2.0 25 200 395 66 245 305 355 10 225 8 10 - 1.1 24
35JM CT9 355 435 375 256 2.5 25 200 395 66 289 305 355 10 225 8 10 - 1.1 28
Short Cased
31JM BT4/5 315 395 301 225 2.5 - - 355 - - - - - - 8 10 - - 13.5
31JM BT9 315 395 333 225 2.5 - - 355 - - - - - - 8 10 - - 15
35JM BT4/5 355 435 301 225 2.5 - - 395 - - - - - - 8 10 - - 14
35JM CT5 355 435 308 225 2.5 - - 395 - - - - - - 8 10 - - 16.5
35JM CT9 355 435 348 225 2.5 - - 395 - - - - - - 8 10 - - 20.5
79
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
Aerofoil fan 40JM - 45JM Section 4.1
4 Pole
40JM/16/4/5/... 45JM/16/4/5/...
2 Pole
40JM/16/2/5/... 45JM/16/2/5/... 45JM/20/2/6/...
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400 500 600
40JM/16/4/5/40 1420 1.50 1.31 1.06
40JM/16/2/5/32 2840 2.60 2.51 2.42 2.35 2.27 2.18 2.08 1.86 1.61
45JM/16/4/5/30 1420 1.80 1.61 1.40 1.1
45JM/16/4/5/40 1420 2.20 1.95 1.72
45JM/16/2/5/20 2840 2.65 2.60 2.54 2.48 2.40 2.31 2.20 2.02 1.80
45JM/20/2/6/34 2910 3.85 3.80 3.70 3.60 3.52 3.40 3.31 3.12 2.90 2.70
Electrical Data
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA
40JM/16/4/5/… 1420 BT9 DX431452 36-40 0.3 0.89 4.6 CD1559 ME3.2D MT3.1 FWD1 52
40JM/16/2/5/… 2840 CT9 DX431203 8-32 1.7 3.7 20 CD1344 N/A N/A FWD2 66
45JM/16/4/5/… 1420 BT9 JL481452 26 0.3 0.89 4.6 CD1559 ME3.2D MT3.1 N/A 52
45JM/16/4/5/… 1420 CT5 DX481460 40 0.58 1.7 6.5 CD1559 ME3.2D MT3.2 FWD1 56
45JM/16/2/5/… 2840 CT9 JL481202 8-20 1.7 3.7 20 CD1344 N/A N/A N/A 66
45JM/20/2/6/… 2910 F22 EX481205 8-34 3.8 7.2 64 CD1343 N/A N/A FWD4 72
220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
40JM/16/4/5/… 1420 BT9 DX411452 34-40 0.3 2.1 5.3 CD1705 ME1.3 MT1.5 52
40JM/16/2/5/… 2840 CT9 JL411203 24-28 1.4 8.3 27 CD1705 N/A N/A 66
45JM/16/4/5/… 1420 BT9 JL461452 24-30 0.3 2.1 5.3 CD1705 ME1.3 MT1.5 52
45JM/16/4/5/… 1420 CT5 DX461466 36-40 0.45 2.8 6 CD1705 ME1.3 MT1.5 5645JM/16/2/5/… 2840 CT9 JL461201 16-18 1.4 8.3 27 CD1705 N/A N/A 66
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.When these fans are operating in excess of 50°C they should be run at full speed only.
For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.Product numbers shown are for Long cased fans.
Wiring diagram references can be found in section 9.2.
80
Section
4 - A
erofoil - JM A
erofoil
Aerofoil fan 40JM - 45JM Section 4.1
Product Motor A B C D E F G H J K L M N P S T U X Max. Fan
Code Range Weight (kg)
Long Cased
40JM BT9:CT9 400 480 375 279 2.5 25 225 450 66 289 350 400 10 250 8 12 - 1.2 30
45JM CT5 450 530 330 306 2.0 25 225 500 66 245 400 450 10 280 8 12 - 1.5 32
45JM BT9:CT9 450 530 375 306 2.5 25 225 500 66 289 400 450 10 280 8 12 - 1.5 32
45JM F22 450 530 520 306 3 25 255 500 66 434 400 450 10 280 8 12 - 1.5 50
Short Cased
40JM BT 400 480 333 225 2.5 - - 450 - - - - - - 8 12 - - 16.5
40JM CT 400 480 333 348 2.5 - - 450 - - - - - - 8 12 - - 21
45JM BT 450 530 333 225 2.5 - - 500 - - - - - - 8 12 - - 18.5
45JM CT 450 530 348 225 2.5 - - 500 - - - - - - 8 12 - - 23
45JM F22 450 530 444 225 3 - - 500 - - - - - - 8 12 - - 40
All dimensions shown in mm.
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Dimensions
Long Cased
Short Cased
81
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
Aerofoil fan 50JM Section 4.1
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
† For 56JM tabular data – see page 83
4 Pole
50JM/16/4/5/... 50JM/20/4/6/...
2 Pole
50JM/ 20/2/6/... †56JM/20/2/6/...
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400 500 600
50JM/16/4/5/34 1420 2.75 2.50 2.21 1.85
50JM/16/4/5/40 1420 3.00 2.75 2.43
50JM/20/4/6/20 1420 1.85 1.70 1.50 1.25
50JM/20/4/6/32 1420 2.60 2.41 2.20 1.95 1.60
50JM/20/4/6/40 1420 2.97 2.77 2.51 2.20
50JM/20/2/6/24 2840 4.30 4.22 4.18 4.05 4.00 3.90 3.80 3.62 3.42 2.60
50JM/20/2/6/34 2840 5.52 5.48 5.35 5.27 5.20 5.09 4.92 4.75 4.45 3.60
Electrical Data
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA
50JM/16/4/5/… 1420 CT5 DX531460 28-34 0.58 1.7 6.5 CD1559 ME3.2D MT3.2 FWD1 57
50JM/16/4/5/… 1420 CT9 JL531454 34-40 0.91 2.49 13 CD1559 ME3.2D MT3.2 N/A 59
50JM/20/4/6/… 1420 BT9 JL531456 16-20 0.3 0.89 4.6 CD1559 ME3.2D MT3.1 N/A 53
50JM/20/4/6/… 1420 CT5 DX531462 26-32 0.58 1.7 6.5 CD1559 ME3.2D MT3.2 FWD1 56
50JM/20/4/6/… 1420 CT9 JL531458 34-40 0.91 2.49 13 CD1559 ME3.2D MT3.2 N/A 58
50JM/20/2/6/… 2840 F22 EX531203 8-24 3.8 7.1 44 CD1343 N/A N/A FWD4 70
50JM/20/2/6/… 2840 PM112 DX531204 26-34 6.2 11.6 100 CD1343 N/A N/A FWD6 74
220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
50JM/16/4/5/… 1420 CT5 DX511464 32-34 0.55 3.7 5.5 CD1705 ME1.6 MT1.5 57
50JM/16/4/5/… 1420 CT9 JL511460 38-40 0.68 4.2 11 CD1705 ME1.6 MT1.5 59
50JM/20/4/6/… 1420 BT9 DX511455 16-20 0.3 2.1 5.3 CD1705 ME1.3 MT1.5 53
50JM/20/4/6/… 1420 CT5 DX511466 30-32 0.55 3.7 5.5 CD1705 ME1.6 MT1.5 56
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.When these fans are operating in excess of 50°C they should be run at full speed only.
For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.Product numbers shown are for Long cased fans.
Wiring diagram references can be found in section 9.2.
Aerofoil fan 50JM Section 4.1
Section
4 - A
erofoil - JM A
erofoil
82
Product Motor A B C D E F G H J K L M N P S T U X Max. Fan
Code Range Weight (kg)
Long Cased
50JM CT5 500 594 330 338 2.0 25 290 560 66 235 450 500 10 315 12 12 - 2.0 34
50JM BT9:CT9 500 594 375 338 2.5 25 290 560 66 280 450 500 10 315 12 12 - 2.0 34
50JM F22/PM112 500 594 520 338 3 25 290 560 66 424 450 500 10 315 12 12 - 2.0 67
Short Cased
50JM BT9 500 594 333 225 2.5 - - 560 - - - - - - 12 12 - - 20
50JM CT5 500 594 308 225 2.5 - - 560 - - - - - - 12 12 - - 20.5
50JM CT9 500 594 348 225 2.5 - - 560 - - - - - - 12 12 - - 25
50JM F22 500 594 444 225 3 - - 560 - - - - - - 12 12 - - 43
50JM PM112 500 594 392 225 3 - - 560 - - - - - - 12 12 - - 50
Dimensions
All dimensions shown in mm.
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Long Cased
Short Cased
Aerofoil fan 56JM - 63JM Section 4.1
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
83
Electrical DataFor graphical data of 56JM 2 Pole see page 69
4 Pole
56JM/20/4/6/... 63JM/20/4/6/...
6 Pole
63JM/20/6/6/...
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400 500 600
56JM/16/4/5/24 1420 3.05 2.82 2.55 2.22 1.82
56JM/16/4/5/32 1420 3.73 3.42 3.23 2.80 2.38
56JM/20/4/6/36 1420 4.05 3.82 3.60 3.21 2.90
56JM/20/2/6/24 2910 6.30 6.20 6.10 6.05 5.90 5.85 5.70 5.46 5.20 4.35
63JM/20/6/6/22 900 2.51 2.2 1.75
63JM/20/6/6/34 900 3.55 3.10 2.50
63JM/20/4/6/18 1420 3.45 3.30 3.10 2.90 2.65 2.25
63JM/20/4/6/32 1420 5.30 5.10 4.81 4.55 4.15 3.82
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA
56JM/16/4/5/… 1420 CT5 JL591452 18-24 0.45 1.6 6 CD1343 ME3.2D MT3.2 N/A 57
56JM/16/4/5/… 1420 CT9 DX591453 26-32 0.91 2.49 13 CD1343 ME3.2D MT3.2 FWD1 5
56JM/20/4/6/… 1420 CT9 DX591458 32-36 1.15 3 14 CD1343 ME3.2D AT7.0 FWD2 61
56JM/20/2/6/… 2910 PM112 EX591201 8-24 6.2 11.6 100 CD1343 N/A N/A FWD6 73
63JM/20/6/6/… 900 CT5 JL661651 20-22 0.3 1.1 3.3 CD1559 ME3.2D MT3.2 N/A 49
63JM/20/6/6/… 900 CT9 JL661652 30-34 0.52 1.7 7.5 CD1559 ME3.2D MT3.2 N/A 50
63JM/20/4/6/… 1420 CT9 DX661453 20-22 1.15 3 14 CD1559 ME3.2D AT7.0 FWD2 61
63JM/20/4/6/… 1420 F22 DX661454 24-32 2.1 5 27 CD1343 N/A AT7.0 FWD2 61
220-240V/50Hz/1φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 230V) (at 230V) Ref Elec- Trans- Level
(˚) (kW) (A) (A) tronic former dBA
56JM/16/4/5/… 1420 CT5 JL571453 22 0.55 3.7 5.5 CD1705 ME1.6 MT1.5 57
56JM/16/4/5/… 1420 CT9 DX571456 28 0.97 6.2 19 CD1705 ME1.6 MT1.8 58
56JM/16/4/5/… 1420 CT9 DX571455 32 0.97 6.2 19 CD1705 ME1.6 MT1.8 58
56JM/20/4/6/... 1420 CT9 DX571459 28 0.97 6.2 19 CD1705 ME1.6 MT1.8 58
63JM/20/4/6/… 1420 CT9 DX641453 16 0.97 6.2 19 CD1705 ME1.6 MT1.8 61
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.When these fans are operating in excess of 50°C they should be run at full speed only.
For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.Product numbers shown are for Long cased fans.
Aerofoil fan 56JM - 63JM Section 4.1
Section
4 - A
erofoil - JM A
erofoil
84
Dimensions
All dimensions shown in mm.
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Wiring diagram references can be found in section 9.2.
Product Motor A B C D E F G H J K L M N P S T U X Max. Fan
Code Range Weight (kg)
Long Cased
56JM CT 560 654 375 368 2.5 25 330 620 66 280 510 560 10 355 12 12 - 2.3 38
56JM F22 560 654 520 368 3 25 330 620 66 424 510 560 10 355 12 12 - 2.3 62
63JM CT 630 724 375 403 3 25 375 690 66 289 580 630 10 400 12 12 - 2.4 52
63JM F22/PM112 630 724 520 403 3 25 375 690 66 434 580 630 10 400 12 12 - 2.4 83
Short Cased
56JM CT5 560 654 308 225 2.5 - - 620 - - - - - - 12 12 - - 22
56JM CT9 560 654 348 225 2.5 - - 620 - - - - - - 12 12 - - 26
56JM PM112 560 654 392 225 3 - - 620 - - - - - - 12 12 - - 52
63JM CT5 630 724 308 225 3 - - 690 - - - - - - 12 12 - - 36
63JM CT9 630 724 348 225 3 - - 690 - - - - - - 12 12 - - 40
63JM F22 630 724 444 225 3 - - 690 - - - - - - 12 12 - - 56
Long Cased
Short Cased
Aerofoil fan 71JM - 80JM Section 4.1
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
85
80JM/20/6/6/...
6 Pole
71JM/20/6/6/... 80JM/25/4/9/...
4 Pole
71JM/20/4/6/... 80JM/20/4/6/...
Electrical Data
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400
71JM/20/6/6/22 900 3.75 3.55 3.00
71JM/20/6/6/36 900 5.55 4.90 4.20
71JM/20/4/6/24 1440 6.45 6.20 6.00 5.75 5.50 5.22 4.87
71JM/20/4/6/20 1440 8.8 8.4 8.0 7.6 7.2 6.8 6.3
80JM/20/6/6/28 935 6.60 5.70 5.20 4.50
80JM/20/6/6/36 935 7.90 7.25 6.50 5.60
80JM/20/4/6/24 1440 9.41 9.00 8.51 8.18 7.82 7.40 6.90
80JM/25/4/9/22 1440 8.50 8.10 7.90 7.60 7.40 7.00 6.60 6.00
80JM/25/4/9/26 1440 9.50 9.25 9.00 8.70 8.40 8.05 7.60 6.90
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Rating Current Current Diagram Sound
rev/min (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (kW) (A) (A) tronic former dBA
71JM/20/6/6/… 900 CT9 JL741652 20-22 0.52 1.7 7.5 CD1559 ME3.2D MT3.2 FWD1 53
71JM/20/6/6/… 900 F22 EX741653 24-36 1.35 3.6 15 CD1559 N/A AT7.0 FWD2 55
71JM/20/4/6/… 1440 F22 EX741401 8-24 2.7 5.8 30 CD1343 N/A N/A FWD3 65
71JM/20/4/6/… 1440 PM112 DX741404 18-36 4.4 9.3 55 CD1343 N/A N/A FWD5 68
80JM/20/6/6/… 935 F22 EX831651 24-26 1.35 3.6 15 CD1559 N/A AT7.0 FWD2 58
80JM/20/6/6/… 935 F22 JL831603 30-36 2.5 6.4 26 CD1343 N/A N/A FWD3 60
80JM/20/4/6/… 1440 PM112 JL831412 8-24 4.4 9.3 55 CD1343 N/A N/A FWD5 69
80JM/25/4/9/… 1440 PM112 EX831405 8-22 4.4 9.3 55 CD1343 N/A N/A FWD5 71
80JM/25/4/9/… 1440 *D132 EX831408 24-26 6.3 12.7 86 CD1343 N/A N/A FWD6 71
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.When these fans are operating in excess of 50°C they should be run at full speed only.
For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.Product numbers shown are for Long cased fans.
* OHP = Thermistor. Maximum pitch angle at 200° = 24°.Wiring diagram references can be found in section 9.2.
Section
4 - A
erofoil - JM A
erofoil
86
Aerofoil fan 71JM - 80JM Section 4.1
Dimensions
All dimensions shown in mm
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Product Motor A B C D E F G H J K L M N P S T U X Max. Fan
Code Range Weight (kg)
Long Cased
71JM CT9 710 804 375 443 3 25 415 770 66 259 660 710 10 440 16 12 - 4.5 54
71JM F22/PM112 710 804 520 443 3 25 415 770 66 404 660 710 10 440 16 12 - 4.5 87
80JM F22/PM112 800 894 520 488 3 25 485 860 66 404 750 800 10 510 16 12 - 5.8 96
80JM D132 800 894 520 525 5 25 485 860 66 400 750 800 12 510 16 12 - 7.0 192
Short Cased
71JM CT9 710 804 348 225 3 - - 770 - - - - - - 16 12 - - 42
71JM F22 710 804 348 225 3 - - 770 - - - - - - 16 12 - - 52
71JM PM112 710 804 348 225 3 - - 770 - - - - - - 16 12 - - 63
80JM F22 800 894 444 225 3 - - 860 - - - - - - 16 12 - - 65
80JM PM112 800 894 392 225 3 - - 860 - - - - - - 16 12 - - 72
80JM D132 800 894 478 260 4 - - 860 - - - - - - 16 12 - - 174
Long Cased
Short Cased
Aerofoil fan 90JM - 100JM Section 4.1
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
87
Electrical Data
8 Pole
90JM/25/8/9/... 100JM/25/8/9/...
4 Pole
90JM/25/4/9/... 100JM/25/4/9/...
100JM/25/6/9/...
6 Pole
90JM/25/6/6/... 100JM/25/6/6/...
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400 500
90JM/25/8/9/34 695 8.20 7.32 6.25
90JM/25/6/6/32 935 9.60 9.00 8.15 7.10
90JM/25/6/9/24 935 8.50 8.05 7.55 7.05 6.55 5.70
90JM/25/4/9/22 1440 12.5 12.1 12.0 11.5 11.1 10.7 10.4 10.0 8.9
90JM/25/4/9/30 1440 16.2 15.2 14.8 14.4 14.0 13.7 13.3 12.4 11.8
100JM/25/8/9/24 695 8.8 7.9 6.7
100JM/25/6/6/22 950 10.8 9.9 9.0 8.1 6.9
100JM/25/6/9/34 960 15.4 14.6 14.0 13.0 12.0 10.8
100JM/25/4/6/22 1470 16.2 15.9 15.2 14.7 14.1 13.8 13.1 11.7 10.0
100JM/25/4/9/20 1470 16.5 16.0 15.5 15.1 14.9 14.3 13.9 12.8 11.6
100JM/25/4/9/24 1470 18.8 18.28 17.75 17.48 17.2 16.3 15.4 14.5 13.6
380-420V/50Hz/3φ
Product Speed Motor Product Pitch Pitch Motor Full Load Starting Wiring Speed Controller
Code Number Angle Angle Rating Current Current Diagram Sound
rev/min 200˚C (at 400V) (at 400V) Ref Elec- Trans- Inverter Level
(˚) (˚) (kW) (A) (A) tronic former dBA
90JM/25/8/9/… 695 F22 JL931802 8-32 32 1.4 4.9 18 CD1343 N/A N/A FWD2 58
90JM/25/6/6/… 935 F22 JL933602 24-32 28 2.5 6.4 26 CD1343 N/A N/A FWD3 65
90JM/25/6/9/… 935 F22 JL931602 8-24 24 2.5 6.4 26 CD1343 N/A N/A FWD3 63
90JM/25/4/9/… 1450 *D132 EX931403 8-16 20 9 16.6 125 CD1343 N/A N/A FWD7 74
90JM/25/4/9/… 1440 *D160 EX931406 24-28 28 13 24.3 172 CD1343 N/A N/A FWD8 75
100JM/25/6/6/… 950 F22 JL133602 8-22 30 2.5 6.42 26 CD1343 N/A AT7.0 FWD3 68
100JM/25/6/9/… 960 *D132 JL131609 28-34 18 6.3 13.7 104 CD1343 N/A N/A FWD6 71
100JM/25/4/6/… 1470 *D132 EX133402 8-20 18 9 16.6 125 CD1343 N/A N/A FWD7 79
100JM/25/4/9/… 1470 *D160 JL131419 8-18 18 13 23.4 164.6 CD1343 N/A N/A FWD8 79
100JM/25/4/9/… 1470 *D160 EX131405 24 20 17 32.1 226.2 CD1343 N/A N/A FWD9 79
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented forcomparative purposes only.
For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.Product numbers shown are for Long cased fans.
* OHP = Thermistor
Aerofoil fan 90JM - 100JM Section 4.1
Section
4 - A
erofoil - JM A
erofoil
88
Dimensions
All dimensions shown in mm.
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Wiring diagram references can be found in section 9.2.
Product Motor A B C D E F G H J K L M N P S T U X Max. Fan
Code Range Weight (kg)
Short Cased
90JM F22 900 1006 520 538 3 25 491 970 66 444 850 900 10 518 16 15 - 5.3 94
90JM D132 900 1006 520 575 5 25 491 970 66 440 850 900 12 518 16 15 - 5.3 206
90JM D160 900 1006 711 575 5 25 491 970 66 629 850 900 10 518 16 15 - 5.3 270
100JM F22 1000 1106 520 588 3 25 547 1070 66 444 950 1000 10 574 16 15 - 6.2 102
100JM D132 1000 1106 625 588 5 25 547 1070 66 440 950 1000 10 574 16 15 - 6.2 227
100JM D160 1000 1106 711 625 6 25 547 1070 66 539 950 1000 12 574 16 15 - 6.2 286
Long Cased
90JM F22 900 1006 444 225 3 - - 970 - - - - - - 16 15 - - 67
90JM D132 900 1006 438 300 5 - - 970 - - - - - - 16 15 - - 143
90JM D160 900 1006 515 300 5 - - 976 - - - - - - 16 15 - - 207
100JM F22 1000 1106 444 225 3 - - 1070 - - - - - - 16 15 - - 72
100JM D132 1000 1106 478 300 5 - - 1070 - - - - - - 16 15 - - 190
100JM D160 1000 1106 643 300 5 - - 1070 - - - - - - 16 15 - - 291
Long Cased
Short Cased
Sec
tion
4 - A
erof
oil - JM
Hig
h T
empe
ratu
re
90
Aerofoil - JM High Temperature Section 4.2
Section
4 - A
erofoil - JM H
igh Tem
perature
Sizes
31JM - (315mm) to 100JM - (1000mm).Other sizes are available on request.
Fan Performance
All fans are tested to the latest internationally recognised standard IS05801 Part 1, installation category D for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance. Coupled with a wide range of diameters, the adjustable pitch Aerofoil impeller gives the exact performancerequired, with a non overloading fan characteristic.
Impellers
A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustablepitch angle availability. The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise.Every cast aluminium component is X-ray examined using Real Time Radiography inspection prior to assembly.The maximum pitch angles shown allow for speed control by frequency inverter.
Motors
Fläkt Woods H.T. Series fans utilise a totally enclosed squirrel cage motor.The grades of motor insulation have been selected to meet the specific requirements for each of the H.T. Categories.These motors are suitable for inverter speed control down to 20% of full speed.
Electrical Supply
400 V / 50 Hz / 3 φ
Temperature Range
Fans are tested in compliance with high temperature test standard directive 89/106/EEC to EN 12101-3, and are fully CE marked accordingly.Fläkt Woods H.T. Series fan motors are sized to run the fans continuously at normal ambient temperatures (-40°C to 50°C), as well as operating at their emergency high temperature category. (All motors are not suitable for starting at temperatures lower than -20°C.).
Most Standard 3 φ fans can be offered for a one off emergency operation at 200°C for 2 hours.Note: During emergency use inverter should be overridden for full speed.
Casings
JM HT Aerofoil fans are available in either a long cased form, complete with an externally mounted pre-wired electrical terminal box.
Casings are spun from sheet steel with integral pre-drilled and radiused inlet flanges. The galvanised finish gives a high resistance to corrosion and is ideal for external as well as internal use.
AccessoriesSilencers, Mounting feet, Spring type vibration isolators, Matching flanges, Flexible connectors, Air operated non return dampers, Guards, Bell mouth inlets.
• Designed for emergency ventilation of hot firesmoke applications
• 300°C or 400°C for two hours operation, CE marked to EN12101-3 2002
• Sizes from 315mm to 1000mm
• All casings are hot dipped galvanised• Volume flows up to 21m3/s • Static pressures up to 600 Pa• Motor protection IP55• Inverter controllable for ambient temperatures
JM HT 300/2 Section 4.2
Sec
tion
4 - A
erof
oil - JM
Hig
h T
empe
ratu
re
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
91
Electrical Data
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400 500 600
31JM/16/2/5/... 2770 1.3 1.25 1.2 1.1 1.05 1.0 0.88
40JM/16/2/5/... 2725 2.6 2.5 2.4 2.3 2.25 2.2 2.1 1.8 1.6
63JM/20/4/6/... 1385 5.4 5.1 4.9 4.7 4.4 4.2
71JM/20/4/6/... 1385 7.8 7.7 7 6.8 6.5 6.1 5.8
80JM/25/4/9/... 1460 12.2 11.9 11.5 11 10.4 10.1 9.8 8.8
90JM/25/4/9/... 1450 16 15.7 15.5 15.2 14.8 14.5 14 13 12 11
100JM/25/4/9/... 1440 20.4 19.6 19 18.7 18.4 18 17.5 16.4 15.5 14.4
380-420V/50Hz/3φProduct Speed Motor Product Pitch Motor Full Load Starting Wiring Speed
Code Number Angle Rating Current Current Diagram Controller Sound
rev/min (at 400V) (at 400V) Ref Inverter Level
(˚) (kW) (A) (A) dBA
31JM/16/2/5/.. 2770 80 EF349232 38 0.9 1.9 9.2 CD1344 FWD1 59
40JM/16/2/5/.. 2725 80 EF439230 32 1.73 3.65 19.3 CD1344 FWD2 48
63JM/20/4/6/.. 1385 100L EF669432 36 3.65 7.04 38.7 CD1344 FWD4 63
71JM/20/4/6/.. 1385 100L EF749431 30 3.6 7.04 38.7 CD1344 FWD4 65
80JM/25/4/9/.. 1460 132M EF839433 36 9 17 113.9 CD1343 FWD7 71
90JM/25/4/9/.. 1450 132M/L EF939431 30 12.1 23.2 181 CD1343 FWD8 76
100JM/25/4/9/.. 1440 160L EF139435 28 18 34.7 170.7 CD1343 FWD9 81
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Performance shown at emergency operating temperatures.
For short cased fans please enquire.
Wiring diagram references can be found in section 9.2.
4 Pole
63JM/20/4/6/... 31JM/16/2/5/...
2 Pole
80JM/20/4/6/... 100JM/25/4/9/... 40JM/16/2/5/...
JM HT 300/2 Section 4.2
Section
4 - A
erofoil - JM H
igh Tem
perature
92
All dimensions shown in mm.
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories).
Product Motor A B C D E G H K L M N P S T X Max. Fan
Code Range (kg) Weight (kg)
Long Cased
31JM/16/2/5/... 2770 315 395 375 235 2.5 175 355 289 265 315 10 200 8 10 0.8 31
40JM/16/2/5/... 2725 400 480 375 279 2.5 225 450 289 350 400 10 250 8 12 1.2 32
63JM/20/4/6/... 1385 630 724 520 403 3 375 690 434 580 630 10 400 12 12 2.5 75
71JM/20/4/6/... 1385 710 804 520 443 3 415 770 404 660 710 10 440 16 12 4.5 77
80JM/25/4/9/... 1460 800 894 520 525 5 485 860 400 750 800 12 510 16 12 5.8 163
90JM/25/4/9/... 1450 900 1006 520 575 5 491 970 444 850 900 12 518 16 15 5.3 177
100JM/25/4/9/... 1140 1000 1006 625 625 5 547 1070 545 950 1000 12 574 16 15 6.2 284
Dimensions
Long Cased
JM HT 400/2 Section 4.2
Sec
tion
4 - A
erof
oil - JM
Hig
h T
empe
ratu
re
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
93
Electrical Data
4 Pole
63JM/20/4/6/...71JM/25/4/9/... 80JM/25/4/9/...100JM/31/4/9/...
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400 500 600
31JM/16/2/5/... 2850 1.25 1.18 1.15 1.05 1.01 0.93 0.85
35JM/16/2/5/... 2750 2.0 1.93 1.9 1.82 1.73 1.65 1.55 1.27
40JM/16/2/5/... 2720 2.6 2.51 2.42 2.35 2.27 2.18 2.08 1.86 1.61
63JM/40/4/6/... 1440 4.9 4.8 4.3 4.1 3.9 3.4
71JM/28/4/9/... 1440 6.9 6.6 6.4 6.2 6.0 5.7 5.4 4.5
80JM/25/4/9/... 1440 10.6 10.3 10 9.8 9.5 9.0 8.6 7.8
90JM/31/4/6/... 1455 14.8 14.5 14.0 13.8 13.2 13.0 12.3 11.9 10.8
100/JM31/4/6/... 1450 17 16.5 16 15.3 14.5 13.7 13.0 11.4 11.0 10.0
100/JM31/4/9/... 1450 20.4 19.6 19.0 18.7 18.4 18 17.5 16.4 15.5 14.4
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Performance shown at emergency operating temperatures.For short cased fans please enquire.Wiring diagram references can be found in section 9.2.
380-420V/50Hz/3φProduct Speed Motor Product Pitch Motor Full Load Starting Wiring Speed
Code Number Angle Rating Current Current Diagram Controller Sound
rev/min (at 400V) (at 400V) Ref Inverter Level
(˚) (kW) (A) (A) dBA
31JM/16/2/5/... 2850 D80 EF349242 40 0.9 1.9 4.47 CD1344 FWD1 61
35JM/16/2/5/... 2750 80 EF389240 40 1.73 3.69 19.2 CD1344 FWD2 66
40JM/16/2/5/... 2720 80 EF439241 32 1.73 3.69 19.2 CD1344 FWD2 66
63JM/40/4/6/... 1440 90L EF669442 28 1.8 3.87 24 CD1344 FWD2 61
71JM/28/4/9/... 1440 100L EF749443 28 3.6 7.82 46.9 CD1344 FWD4 68
80JM/25/4/9/... 1440 132S EF839444 30 6.6 12.9 86.4 CD1343 FWD6 71
90JM/31/4/6/... 1455 132M EF939440 26 11 21.1 139 CD1343 FWD7 75
100/JM31/4/6/... 1450 132M EF139448 24 11 21.1 139 CD1343 FWD7 81
100/JM31/4/9/... 1450 160L EF139447 28 18 34.7 163 CD1343 FWD9 86
40JM/16/2/5/...
4 Pole
31JM/16/2/5 35JM/16/2/5/...
JM HT 400/2 Section 4.2
Section
4 - A
erofoil - JM H
igh Tem
perature
94
Product Motor A B C D E G H K L M N P S T X Max. Fan
Code Range (kg) Weight (kg)
Long Cased
31JM/16/2/5/... D80 315 395 375 235 2.5 175 355 289 265 315 10 200 8 10 0.8 31
35JM/16/2/5/... 80 355 435 375 358 2.5 200 395 285 305 355 10 225 8 5 0.75 36
40JM/16/2/5/... 80 400 480 375 279 2.5 225 450 289 350 400 10 250 8 12 1.2 32
63JM/20/4/6/... 90L 630 724 520 403 3 375 690 434 580 630 10 400 12 12 2.5 73
71JM/25/4/9/... 100L 710 804 520 443 3 415 770 404 650 710 10 440 16 12 4.5 77
80JM/25/4/9/... 132S 800 894 520 525 5 485 860 400 750 800 12 510 16 12 5.8 166
90JM/25/4/9/... 132M 900 1006 520 575 5 491 970 444 850 900 12 518 16 15 5.3 177
100JM/31/4/6/... 132M 1000 1106 520 625 5 547 1070 444 950 1000 12 574 16 15 6.2 226
100JM/31/4/9/... D160 1000 1106 625 625 5 547 1070 545 950 1000 12 574 16 15 6.2 284
Dimensions
All dimensions shown in mm.
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Long Cased
JM Aerofoil ATEX Section 4.3
Sec
tion
4 - A
erof
oil - JM
ATE
X
95
Atex standards now available with the Fläkt Woods JM Aerofoil range. Contact your local Express Distributor for further details on availability.
The high specification Industrial Markets in Europe require high specification products for the hazardous application sector. To support our customers Fläkt Woods can offer ATEX compliance on its JM Aerofoil axial fans and its new Centripal EU range of centrifugal fans. This combined range is considered the widest range available from a single manufacturer.
What is ATEX?
As from July 1, 2003 the new EU ATEX Directive requires most products to be used in potentially explosive environments to be ATEX compliant. The new directive covers a surprisingly large range of equipment including products used in petro-chemicalplants, chemicals, pharmaceuticals, battery rooms, flourmills, grain silos and other areas where a potentially explosive atmospheremay be present.
Potential explosive hazards are very common and include gases, vapours, mists and dust. The specific mixture being handledcategorises the features each product must include.
Who does ATEX apply to?
End users have the ultimate responsibility to ensure ATEX compliance and Fläkt Woods can assist in this area. Our website www.atex-fans.com provides much of the information and forms required.
• Manufacturers • OEM’s • Specifiers • Distributors
Products installed after 1/7/03 may have to be replaced should they not comply with the ATEX directive. Users must act now to specify the correct product.
Fläkt Woods ATEX Compliant Fans
Fläkt Woods offers both Aerofoil axial fans and Centripal EU range of centrifugal fans that are all ATEX compliant. We have ensured that all the necessary systems are in place during production to continue ATEX compliance. Fläkt Woods have invested heavily in Engineering design and specification to comply with ATEX.
Fläkt Woods fans have been modified in a number of ways including changes to motors, materials, locking systems and conduit systems as well as adapting and revising product guides and operation manuals.
Acceptance throughout Europe
Having the ability to supply ATEX compliance and by CE marking our fans, Fläkt Woods are able to sell fan products anywhere in Europe without further requirements being applied. This also enables refurbishment of existing installations OEM customers can be confident in using Fläkt Woods products to gain the relevant certification of their products.
Fläkt Woods Certificate number ST M07 TEC 2885
For more information visit www.atex-fans.com
JM Aerofoil ATEX Section 4.3
Section
4 - A
erofoil - JM A
TEX
96
Performance Range covered by The JM ATEX range.
Regulation t-box fixings and cable connectionsas per standard requirements.
Sec
tion
4 - A
erof
oil - JM
Bifur
cate
d
JM Bifurcated Aerofoil Section 4.4
Sizes
40JM.Bif - 400mm, 50JM.Bif - 500mm, 63JM.Bif - 630mm, 80JM.Bif - 800mm.800 and 1000mm JM.Bif available please contact Fläkt Woods for details.Also larger sizes are available, please enquire.
Fan Performance
Coupled with the above fan diameters the fully adjustable pitch Aerofoil impeller gives the exact performance required with a non overloading fan characteristic. Higher pressures are obtained by multi-staging the Bifurcated Aerofoil fan.
Impellers
A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustable pitch angle availability.
The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise.Every component is X-rayed using Real Time Radiography inspection prior to assembly. The maximum pitchangles shown allow for speed control by frequency inverter.
Motors
All motors are totally enclosed fan cooled class F insulation with protection to IP55. All motors are supplied with sealed for life bearings or extended lubricators.
These motors are suitable for inverter speed control down to 20% of full speed.
Electrical Supply
380 - 420 V / 50 Hz / 3 φ
Temperature Range
Up to 200˚C continuous operation.
Casings
Bifurcated fans are available long case only. Long casing covers impeller and motor and has duct mounted terminal box. The hot dipped galvanised casing gives a high resistance to corrosion.
Accessories
Silencers, Mounting feet, Vibration isolators, Matching flanges, Flexible connectors, Guards, Bell mouth inlets.
• 400mm - 800mm diameter• Volume flow up to 7 m3/s • Static pressures up to 650 Pa• Suitable for temperatures up to 200°C• Motor protection IP55• Overheat protection fitted as standard
• All aluminium cast components are x-ray examined
• All casings are hot dipped galvanised• Multi-stage is available for higher pressures• All casings are hot dipped galvanised• Inverter speed controllable
98
Section
4 - A
erofoil - JM B
ifurcated
JM Bifurcated Aerofoil Section 4.4
Sec
tion
4 - A
erof
oil - JM
Bifur
cate
d
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
99
Electrical Data
80°C
Performance Data
380-420V/50Hz/3φProduct Speed Motor Product Pitch Motor Full Load Starting Wiring Speed
Code Number Angle Rating Current Current Diagram Controller Sound
rev/min (at 400V) (at 400V) Ref Inverter Level
(˚) (kW) (A) (A) dBA
40JM.Bif/16/4/5/… 1440 D71C DB245001 8-38 0.25 0.79 3.5 1344 N/A 57
40JM.Bif/20/2/6/… 2910 F2225 DB245003 8-32 2 4.5 30 1343 FWD2 74
50JM.Bif/16/4/5/… 1440 D80C DB275001 8-38 0.75 2.0 9.9 1344 FWD1 63
50JM.Bif/20/2/6/… 2910 F2229 DB275005 8-30 5.5 11.1 90 1343 FWD5 80
63JM.Bif/20/4/6/… 1440 F2245 DB305001 8-32 2.2 5.0 30 1344 FWD2 71
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Wiring diagram references can be found in section 9.2.
200°C380-420V/50Hz/3φ
Product Speed Motor Product Pitch Motor Full Load Starting Wiring Speed
Code Number Angle Rating Current Current Diagram Controller Sound
rev/min (at 400V) (at 400V) Ref Inverter Level
(˚) (kW) (A) (A) dBA
40JM.Bif/20/4/6/40 1440 F22c JN245005 8-40 0.5 1.49 9.5 1343 FWD1 58
40JM.Bif/20/2/6/32 2950 F22c JN245004 8-32 2.0 4.25 32 1343 FWD2 74
50JM.Bif/20/4/6/32 1440 F22c JN275007 8-32 0.75 3.0 16.4 1343 FWD1 63
50JM.Bif/20/2/6/24 2950 F22c JN275004 8-24 4.0 8.04 68 1343 FWD4 79
63JM.Bif/20/4/6/30 1440 F22c JN305002 8-30 2.0 4.4 2.7 1344 FWD2 70
JM Bifurcated Aerofoil Section 4.4
Section
4 - A
erofoil - JM B
ifurcated
100
Dimensions
40JM.Bif-50JM.Bif
All dimensions shown in mm
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Product Motor A B C D E F G H J K L M N P Q S T Weight
Code Range (kg)
40JM.Bif/20/4/6/40 F2225 400 524 727 367 3 375 332 450 27 641 350 400 10 250 3 8 12 72
50JM.Bif/20/4/6/32 F2225 500 610 787 408 3 375 371 560 27 691 450 500 10 315 3 12 12 83
50JM.Bif/20/4/6/32 F2229 500 610 787 408 3 430 371 560 27 691 450 500 10 315 3 12 12 93
63JM.Bif/20/4/6/30 F2245 630 724 616 436 3 400 400 690 27 530 580 630 14 400 3 12 12 112
80JM.BIF/20/4/6/20 F2249 800 894 660 520 3 468 484 860 27 544 750 800 10 510 5 16 12 155
63JM.Bif - 80JM.Bif
Sec
tion
4 - A
erof
oil - B
ifur
cate
d Ser
ies
33
102
JM Bifurcated Series 33 Fan Section 4.5
Section
4 - A
erofoil - Bifurcated S
eries 33
Sizes
15JM.Bif -152mm, 25JM.Bif - 254mm, 30JM.Bif - 305mm.
Fan Performance
Ideally suited for exhausting or recirculating fumes, gases and hot air up to temperatures of 200°C.Motor must have access to ambient air. All fans have non overloading characteristics.
Impellers
Cast in aluminium silicon alloy and has a fixed pitch aerofoil section blade. This ensures strength, reliability and performance at high temperature.
Motors
All motors are totally enclosed fan cooled, class F insulation with motor protection to IP55. All motors are supplied with sealed for life bearings.
Electrical Supply
220 - 240 V / 50 Hz / 1 φ380 - 420 V / 50 Hz / 3 φ
Temperature Range
Up to 200°CFor higher temperatures please enquire.
Casings
All casings are hot dip galvanised for long life and a high resistance to corrosion. A seal is provided on the motor shaft.
Accessories
Silencers, Mounting feet/plates, Vibration isolators, Matching flanges, High temperature flexible connectors.
• 152mm - 305mm diameter• Volume flow up to 0.89 m3/s • Static pressures up to 380 Pa
• Suitable for temperatures up to 200°C• Motor protection IP55• Series 33 is cost effective solution to
Bifurcated applications
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
103
JM Bifurcated Series 33 Fan Section 4.5
Sec
tion
4 - A
erof
oil - B
ifur
cate
d Ser
ies
33
Electrical Details
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, based on form B running under free field conditions, and are presented for comparative purposes only. Cylindrical silencers are available as standard. Bifurcated fans are not suitable for speed regulation.
Wiring diagram references can be found in section 9.2.
Performance Data
Product Speed m3/s at Pa (Static)
Code rev/min 0 25 50 75 100 150 200 250 375
25JM.33 1400 0.29 0.25 0.19
25JM.33 2900 0.57 0.54 0.52 0.51 0.49 0.46 0.38
30JM.33 1400 0.49 0.44 0.38 0.31
30JM.33 2900 0.98 0.96 0.93 0.91 0.88 0.83 0.77 0.70 0.44
380-420V/50Hz/3φProduct Speed Motor Product Motor Full Load Starting Wiring Speed
Code Number Rating Current Current Diagram Controller Sound
rev/min (at 400V) (at 400V) Ref Inverter Level
(kW) (A) (A) dBA
25JM.Bif.33 1400 D63C DB215608 0.18 0.57 2.28 CD1344 FWD1 40
25JM.Bif.33 2900 D71C DB215609 0.37 0.9 4.95 CD1344 FWD1 55
30JM.Bif.33 1400 D63C DB025608 0.18 0.57 2.28 CD1344 FWD1 46
30JM.Bif.33 2900 D71C DB025609 0.37 0.9 4.95 CD1344 FWD1 63
JM Bifurcated Series 33 Fan Section 4.5
Section
4 - A
erofoil - Bifurcated S
eries 33
104
.All dimensions shown in mm
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Product Motor A B C D E H J L M S T Weight
Code Range (kg)
15JM.33 D63 152 208 610 257 1.6 184 CM20 - - 4 8 15
25JM.33 D63 254 324 489 400 2 299 CM20 222 254 8 10 21
25JM.33 D71 254 324 489 400 2 299 CM20 222 254 8 10 24
30JM.33 D63 305 375 584 470 2 349 CM20 273 305 8 10 26
30JM.33 D71 305 375 584 470 2 349 CM20 273 305 8 10 28
Dimensions
JM Aerofoil - 2 Speed Section 4.6
Sec
tion
4 - A
erof
oil - JM
Aer
ofoi
l 2 S
peed
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
105
2 speed fans offer energy saving characteristics. Fläkt Woods offer a range of 2 speed JM Aerofoil fans on Standard delivery to suit most requirements
Performance Data
Performance is shown at highest speed.
Electrical Data - Pole Change Type
Product Speed m3/s at Pa (Static)
Code rev/min 0 50 100 150 200 250 300 400
31JM/16/2-4/5/38 1420/700 1.3 1.25 1.2 1.15 1.0 0.98 0.86
40JM/16/4-8/5/38 1420/700 1.46 1.28 1.02
40JM/16/2-4/5/26 2910/1440 2.24 2.18 2.12 2.07 1.98 1.92 1.82 1.66
50JM/16/4-8/5/40 1420/700 3.02 2.69 2.44 2.05
50JM/20/2-4/6/30 2900/1400 5.1 5.0 4.95 4.85 4.75 4.6 4.45 4.3
56JM/20/4-8/6/40 1420/720 4.3 4.1 3.8 3.5 3.07
56JM/20/2-4/6/20 2910/1400 5.6 5.4 5.3 5.2 5.1 5.0 4.9 4.7
63JM/20/4-8/6/28 1420/720 4.6 4.4 4.2 3.85 3.6 3.25
63JM/20/4-8/6/36 1440/700 5.9 5.64 5.26 4.96 4.60 4.20
63JM/25/2-4/9/22 2910/1470 7.2 7.1 7.0 6.9 6.8 6.7 6.6 6.4
71JM/20/4-8/6/26 1440/700 6.85 6.5 6.3 6.1 5.85 5.7 5.4
80JM/25/4-8/9/28 1440/730 10.1 9.80 9.50 9.25 9.0 8.6 8.2 7.2
90JM/25/4-8/9/32 1470/730 16.3 15.9 15.5 15.1 14.8 14.4 13.9 13.0
100JM/25/6-12/9/26 960/480 13.0 12.2 11.5 10.6 9.9 9.0
100JM/25/4-8/9/22 1470/730 17.5 17.2 16.9 16.2 16.0 15.5 15.0 13.6
380-420V/50Hz/3φProduct Speed Motor Product Pitch Motor Full Load Starting Wiring
Code Number Angle Rating Current Current Diagram Sound EDC22
rev/min (at 400V) (at 400V) Ref Level 2 Speed/
(˚) (kW) (A) (A) dBA DOL Starter
40JM/16/4-8/5/38 1420/700 CT5 EL431480 8-38 0.5/0.06 1.28/0.5 3.7/1.0 CD1466 50 418141
40JM/16/2-4/5/26 2910/1440 CT9 EL431280 8-26 1.4/0.17 3.1/1.1 16.5/5.0 CD1466 63 418142
50JM/16/4-8/5/40 1420/700 CT9 EL531480 8-40 0.9/0.12 2.5/1.0 9.0/2.5 CD1466 59 418142
50JM/20/2-4/6/30 2900/1400 PM112 EL531281 8-30 5.0/0.65 10.1/3.2 78/20 CD1466 73 418143
56JM/20/4-8/6/40 1420/720 F22 EL591480 8-40 1.8/0.24 4.3/1.5 20.0/5.0 CD1466 62 418144
56JM/20/2-4/6/20 2910/1400 PM112 EL591281 8-20 5.0/0.65 10.1/3.2 78/20 CD1466 73 418143
63JM/20/4-8/6/28 1420/720 F22 EL661481 8-28 1.8/0.24 4.3/1.5 20.0/5.0 CD1466 60 418144
63JM/20/4-8/6/36 1440/700 F22 EL661480 28-36 3.1/0.4 6.8/2.2 37/7.5 CD1466 62 418147
63JM/25/2-4/9/22 2910/1470 D160 EL661281 8-22 12/1.5 22.6/3.1 130/32 CD1466 74 418148
71JM/20/4-8/6/26 1440/700 F22 EL741480 8-26 3.1/0.4 6.8/2.2 37/7.5 CD1466 65 418147
80JM/25/4-8/9/28 1440/730 D132 EL831481 8-28 6.3/0.82 12.3/2.8 72/14 CD1466 72 418149
90JM/25/4-8/9/32 1470/730 D160 EL931481 8-32 13.4/1.68 24.7/5.34 154/27 CD1466 76 418150
100JM/25/6-12/9/26 960/480 D132 EL131681 8-26 4.7/0.56 10.4/2.3 52/8.5 CD1466 70 418154
100JM/25/4-8/9/22 1470/730 D160 EL131481 8-22 13.4/1.68 24.7/5.34 154/27 CD1466 80 418150
Sound pressure levels quoted are average dB(A) at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
Wiring diagram references can be found in section 9.2.
380-420V/50Hz/3φProduct Speed Motor Product Pitch Motor Full Load Starting Wiring
Code Number Angle Rating Current Current Diagram Sound EDC19
rev/min (at 400V) (at 400V) Ref Level 2 Speed/
(˚) (kW) (A) (A) dBA DOL Starter
31JM/16/2-4/5 2820/1460 71 EL341282 38 0.66/0.08 1.62/0.61 7.29/2.26 CD1371 62 Enquire
40JM/16/2-4/5 2885/1465 90L EL431283 26 1.3/0.17 2.91/0.8 18.6/4.05 CD1371 63 Enquire
50JM/20/2-4/6 2875/1445 112M EL531282 24 3.8/0.48 7.71/1.28 47.8/6.4 CD1371 72 Enquire
50JM/20/4-8/6 1460/710 90L EL531481 38 0.9/0.25 2.92/1.27 6.13/2.29 CD1371 59 Enquire
56JM/20/2-4/3 2875/1445 112M EL592201 22 3.8/0.48 7.71/1.28 47.8/6.4 CD1371 73 Enquire
63JM/20/4-8/6 1460/710 90L EL661401 16 0.9/0.25 2.92/1.27 6.13/2.29 CD1371 59 Enquire
Electrical Data - Dual Wound Type
JM Aerofoil - 2 Speed Section 4.6
Section
4 - A
erofoil - JM A
erofoil 2 S
peed
106
Product Motor A B C D E F G H J K L M N P S T X Max. Fan
Code Range Weight (kg)
31JM D71 315 395 975 235 2.5 25 175 355 66 265 315 315 10 200 8 10 0.8 31
40JM CT 400 480 375 279 2.5 25 225 450 66 290 350 400 10 250 8 12 1.2 30
50JM CT 500 594 375 338 2.5 25 290 560 66 280 450 500 10 315 12 12 2.0 34
50JM F22 500 594 520 338 3 25 290 560 66 424 450 500 10 315 12 12 2.0 65
56JM F22 560 654 520 368 3 25 330 620 66 424 510 560 10 355 12 12 2.3 67
63JM F22 630 724 711 403 3 25 375 690 66 434 580 630 10 400 12 12 2.4 70
63JM D160 630 724 520 440 6 25 375 690 66 619 580 630 12 400 12 12 4.8 270
71JM F22 710 804 520 443 3 25 415 770 66 404 660 710 10 440 16 12 4.5 85
80JM D132 800 894 520 525 5 25 485 860 66 400 750 800 12 510 16 12 7.0 192
90JM D160 900 1006 711 575 5 25 491 970 66 629 850 900 12 518 16 15 5.3 270
100JM D132 1000 1106 520 625 5 25 547 1070 66 444 950 1000 12 574 16 15 6.2 227
100JM D160 1000 1106 711 625 6 25 547 1070 66 539 950 1000 12 574 16 15 6.2 286
Dimensions
All dimensions shown in mm
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Long Cased
Sec
tion
4 - A
erof
oil - JM
Mul
ti-S
tage
108
Aerofoil - JM Multi-Stage Section 4.7
Section
4 - A
erofoil - JM M
ulti-Stage
Sizes
31JM - 315mm, 35JM - 355mm, 40JM - 400mm, 45JM - 450mm, 50JM - 500mm, 56JM - 560mm, 63JM - 630mm, 80JM - 800mm.
Fan Performance
All fans are tested to the latest internationally recognised standard IS05801 1997, installation category D for aerodynamic performance and BS848 Part 2 (1985) for acoustic performance.
Coupled with the above fan diameters, the adjustable pitch Aerofoil impeller gives the exact performancerequired, with a non overloading fan characteristic.
Impellers
A unique high efficiency aerofoil section blade with a purposely smoothed hub and clamp plate for adjustablepitch angle availability.
The Fläkt Woods impellers are all high pressure die cast to offer thin aerofoil sections for low generation of noise.Every cast aluminium component is X-ray examined using Real Time Radiography prior to assembly.
The maximum pitch angles shown allow for speed control by frequency inverter.
Motors
All motors are totally enclosed air stream rated class F insulation. Constructed from aluminium as standard withspecial ‘T’ slot or pad mounted fixings. Single speed motors are suitable for speed control by frequency inverters.
Suitable for horizontal through to vertical shaft operation. Supplied IP55, with removable drain plugs.
Sealed for life bearings lubricated with wide temperature range grease.
Motors are fitted with thermostat overheat protection as standard.These motors are suitable for inverter speed control down to 20% of full speed.
Electrical Supply
380 - 420 V / 50 Hz / 3 φ
Temperature Range
-40°C to 50°C as standard. (All motors are not suitable for starting at temperatures lower than -20°C.) Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C. When these fans are operating in excess of 50°C they should be run at full speed only. Other fans can be operated up to 70°C with appropriate deration of motors.
Most standard 3φ fans can be offered for a one off emergency operation at 200˚C for 2 hours.
Casings
JM Aerofoil fans are available long cased, complete with an externally mounted pre-wired electrical terminal box.
Casings are spun from sheet steel with integral pre-drilled and radiused inlet flanges. The galvanised finish gives a high resistance to corrosion and is ideal for external as well as internal use.
Accessories
Silencers, Mounting feet, Vibration isolators, Matching flanges, Flexible connectors, Air operated non return dampers, Guards, Bell mouth inlets.
• 315mm - 800mm diameter• Volume flow up to 9 m3/s • Static pressures up to 1500 Pa• High energy efficiency• All casings are hot dipped galvanised
• Low installed noise levels• Motor protection IP55• Overheat protection fitted as standard• Inverter controllable
Aerofoil - JM Multi-Stage Section 4.7
Sec
tion
4 - A
erof
oil - JM
Mul
ti-S
tage
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
109
Performance DataProduct Speed m3/s at Pa (Static)
Code rev/min 0 100 200 300 400 500 800 1000 1200 1500
31JM2/16/4/5/40/32 1420 0.75 0.68 0.58
35JM2/16/4/5/40/32 1420 1.19 1.08 0.93 0.78
35JM2/16/2/5/24/20 2840 1.5 1.45 1.4 1.38 1.35 1.3 1.15 1.0 0.85
40JM2/16/2/5/27/22 2840 2.45 2.4 2.3 2.25 2.2 2.15 1.9 1.75 1.6
45JM2/16/4/5/40/32 1420 2.6 2.45 2.18 1.95 1.55
45JM2/20/2/6/29/24 2910 3.7 3.64 3.61 3.59 3.58 3.50 3.25 3.11 2.95 2.80
50JM2/20/4/6/41/32 1420 3.6 3.45 3.30 3.10 2.8 2.50
50JM2/20/2/6/20/16 2910 4 3.9 3.8 3.7 3.65 3.6 3.45 3.3 3.15 3
50JM2/20/2/6/30/24 2910 5.6 5.5 5.4 5.3 5.2 5.2 4.9 4.8 4.55 4.3
56JM2/20/4/6/30/24 1420 3.8 3.7 3.4 3.2 2.95 2.7
56JM2/20/4/6/36/28 1420 4.4 4.2 4.0 3.75 3.55 3.2
63JM2/20/4/6/35/28 1420 6.5 6.3 6.1 5.8 5.5 5.2
63JM2/25/4/9/40/32 1440 7.2 7.0 6.8 6.6 6.43 6.3 5.5 4.85
80JM2/25/4/9/20/16 1440 8.4 8.2 8.0 7.7 7.5 7.2 6.6 5.8 4.6
Sound pressure levels quoted are average dBA at 3 m distance over a sphere, under free field conditions and are presented for comparative purposes only.
† Speed controllers sized one per two stage fan.
Fans that include BT or CT motors can be continuously operated at temperatures up to 70°C.
When these fans are operating in excess of 50°C they should be run at full speed only. Product numbers shown are for Long cased fans.
For Short cased fans please omit the prefix from the product number and state S-type on enquiries/orders.
Wiring diagram references can be found in section 9.2.
Electrical Data380-420V/50Hz/3φ
Product Speed Motor Product Motor Full Load Starting Wiring †Speed
Code Number Rating Current Current Diagram Controller Sound
rev/min (at 400V) (at 400V) Ref Inverter Level
(kW) (A) (A) dBA
31JM2/16/4/5/40/32 1420 BT4 EQ341451 0.13 0.5 1.8 CD1344 FWD1 57
35JM2/16/4/5/40/32 1420 BT5 EQ381402 0.13 0.5 1.8 ENQ FWD1 60
35JM2/16/2/5/24/20 2840 CT5 EQ381203 0.95 2 9.5 CD1344 FWD2 76
40JM2/16/2/5/27/22 2840 CT9 EQ431203 1.7 3.5 20 CD1344 FWD4 80
45JM2/16/4/5/40/32 1420 CT5 EQ481453 0.58 1.7 6.5 CD1343 FWD2 67
45JM2/20/2/6/29/24 2840 F22 EQ481205 3.8 7.2 64 CD1343 FWD6 84
50JM2/20/4/6/41/32 1420 CT9 EQ531408 1.4 3.5 14 CD1343 FWD3 73
50JM2/20/2/6/20/16 2840 F22 EQ531203 3.8 7.2 64 CD1343 FWD6 84
50JM2/20/2/6/30/24 2840 PM112 EQ531204 6.2 11.6 100 CD1343 FWD8 88
56JM2/20/4/6/30/24 1420 CT9 EQ591458 1.15 3 14 CD1343 FWD3 73
56JM2/20/4/6/36/28 1420 CT9 EQ591408 1.4 3.5 14 CD1343 FWD3 75
63JM2/20/4/6/20/16 1440 F22 EQ661407 2.7 5.8 30 CD1343 FWD5 78
63JM2/25/4/9/40/32 1440 PM112 EQ661405 4.4 9.3 55 CD1343 FWD7 80
80JM2/25/4/9/20/16 1440 PM112 EQ831404 4.4 9.3 55 CD1343 FWD7 82
Aerofoil - JM Multi-Stage Section 4.7
Section
4 - A
erofoil - JM M
ulti-Stage
110
All dimensions shown in mm
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Dimensions
Long Cased
Product Motor A B C D E F G H J K L M N P S T W X Weight
Code (kg) (kg)
31JM2/16/4/5/40/32 BT4 315 395 750 235 2.5 25 175 355 66 290 265 315 10 200 8 10 375 0.8 44
35JM2/16/4/5/40/32 BT5 355 435 750 256 2.5 25 200 395 66 290 305 355 10 225 8 10 375 1.1 48
35JM2/16/2/5/24/20 CT5 355 435 750 266 2.5 25 200 395 66 290 305 355 10 225 8 10 375 1.1 56
40JM2/16/2/5/27/22 CT9 400 480 750 279 2.5 25 225 450 66 290 350 400 10 250 8 12 375 1.2 60
45JM2/16/4/5/40/32 CT5 450 530 750 306 2.5 25 255 500 66 290 400 450 10 280 8 12 375 1.5 64
45JM2/20/2/6/29/24 F22 450 530 1040 306 3 25 255 500 66 434 400 450 10 280 8 12 520 1.5 88
50JM2/20/4/6/41/32 CT9 500 564 750 338 2.5 25 290 560 66 280 450 500 10 315 12 12 375 2.0 68
50JM2/20/2/6/20/16 F22 500 594 1040 338 3 25 290 560 66 424 450 500 10 315 12 12 520 2.0 108
50JM2/20/2/6/30/24 PM112 500 594 1040 338 3 25 290 560 66 424 450 500 10 315 12 12 520 2.0 130
56JM2/20/4/6/30/24 CT9 560 654 750 368 2.5 25 330 620 66 280 510 560 10 355 12 12 375 2.3 76
56JM2/20/4/6/36/28 CT9 560 654 750 368 2.5 25 330 620 66 280 510 560 10 355 12 12 375 2.3 76
63JM2/20/4/6/20/16 F22 630 724 1040 403 3 25 375 690 66 434 580 630 10 400 12 12 520 2.4 140
63JM2/25/4/9/40/32 PM112 630 724 1040 403 3 25 375 690 66 434 580 630 10 400 12 12 520 2.4 162
80JM2/25/4/9/20/16 PM112 800 894 1040 488 3 25 485 860 66 434 750 800 10 510 16 12 520 5.8 188
JM - Accessories Section 4.8
Sec
tion
4 - J
M- A
cces
sori
es
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
111
JM Damper
JM Mounting Feet
JM – Matching Flanges and Flexible Connector
Note: Flexible Connection weight includes two Matching Flanges.Suitable for up to 600˚C emergency operation for 2 hours and 200˚C continuous.
Product Product Frame G L M N P T V WCode Number Size
315 DA408199 BT/CT.F22 175 265 315 10 200 10 20 60
355 DA408200 BT/CT.F22 200 305 355 10 225 10 20 60
400 DA408201 BT/CT.F22 225 350 400 10 250 12 20 60
450 DA408202 BT/CT,F22 255 400 450 10 280 12 20 60
500 DA408203 BT/CT,F22 290 450 500 10 315 12 25 65
560 DA408204 BT/CT,F22 330 510 560 10 355 12 25 65
630 DA243495 BT/CT,F22 375 580 630 10 400 14 25 65
710 DA245874 BT/CT,F22 415 660 710 10 440 14 25 80
800 245024 BT/CT,F22 485 750 800 12 510 14 25 80
800 249468 D132 485 750 800 1 510 14 25 80
900 249467 F22 491 850 900 12 518 14 25 60
900 249258 D132 491 850 900 12 518 14 25 60
1000 249464 F22 547 950 1000 10 574 15 25 60
1000 249255 D132 547 50 1000 12 574 15 25 60
Suitable Product Numbers Weight (kg)
for fan Matching Flexible C Matching Flexible
OA Flange Connector Flange Connection
315 DA408238 DA414865 110 1.1 3.3
355 DA501351 DA414866 110 1.3 3.9
400 DA074913 DA414867 110 1.5 4.5
450 DA501353 DA414868 110 1.7 5.0
500 DA074914 DA414869 110 2.0 5.5
560 DA501355 DA414901 110 2.3 6.8
630 DA074915 DA414844 160 3.0 7.5
710 DA074916 DA414845 160 3.2 8.1
800 74917 414846 160 3.6 9.1
900 404841 414847 160 4.1 10.4
1000 74918 414848 160 4.6 11.6
Note: Suitable for up to 400˚C emergency operation and 200˚C continuous.
Suitable for Product Weightfan OA Number C D kg
315 414942 225 – 8
355 414943 225 – 9
400 414944 225 17 10
450 414945 225 39 12
500 414473 225 75 16
560 414474 225 125 18
630 414475 225 176 20
710 414476 225 210 23
800 414477 225 270 27
900 414478 225 305 31
1000 414479 225 345 36
112
JM - Accessories Section 4.8
Section
4 - JM
- Accessories
Acoustic Performance B Type (without Pod)
Acoustic Performance C Type (with Pod)
Silencer
The above silencers give the following approximate dBA reductions:B Type 1 diameter length – 7 to 10 dBA C Type 1 diameter length – 12 to 15 dBAFor full acoustic details and resistance to airflow for type C see publication SPO1
Acoustic Performance (dB) – Octave Band Mid Frequency – HzBore Dia. Length
63 125 250 500 1K 2K 4K 8Kmm (D)
315 1D 1 2 4 9 11 10 9 7
355 1D 1 2 4 10 12 10 9 7
400 1D 2 3 5 10 13 11 9 8
450 1D 2 3 6 12 13 11 10 6
500 1D 2 3 6 13 14 10 10 5
560 1D 2 4 7 14 14 19 10 7
630 1D 2 5 7 15 13 8 9 8
710 1D 3 5 7 15 13 9 9 8
800 1D 3 5 8 16 12 9 9 8
900 1D 3 5 10 17 13 11 10 8
1000 1D 4 5 11 16 11 10 8 9
Acoustic Performance (dB) – Octave Band Mid Frequency – HzBore Dia. Length
63 125 250 500 1K 2K 4K 8Kmm (D)
315 1D 2 5 5 9 18 20 18 15
355 1D 2 5 6 9 18 22 19 16
400 1D 2 6 6 10 19 24 20 17
450 1D 2 4 7 13 20 23 22 17
500 1D 2 3 8 16 21 22 21 17
560 1D 3 5 8 16 20 18 19 15
630 1D 3 5 8 15 19 16 14 12
710 1D 3 5 8 15 19 15 14 12
800 1D 4 5 8 16 19 15 14 13
900 1D 4 5 9 17 19 15 14 13
1000 1D 5 5 11 18 19 15 14 13
Suitable Product Numbers Weight (kg)
for fan B Type C Type
OA (Pod Kit) B C J B Type C Type
315 DS211401 DA415792 415 315 M8 ID 13
355 DS221401 DA415793 455 355 M8 12 15
400 DS241401 DA415794 500 400 M10 15 18
450 DS251401 DA415795 600 450 M10 20 24
500 DS271401 DA415796 650 500 M10 25 29
560 DS281401 DA415797 710 560 M10 30 35
630 DS301401 DA415798 780 630 M10 35 42
710 DS311401 DA415799 860 710 M10 44 53
800 331401 416212 1000 800 M10 55 66
900 341401 416213 1100 900 M12 70 84
1000 351401 416214 1200 1000 M12 82 100
JM – Cylindrical Silencers
JM - Accessories Section 4.8
Sec
tion
4 - J
M- A
cces
sori
es
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
113
JM Bell Mouth Inlet – Fan with flanged inlet only
All dimensions shown in mm
Suitable Product Numbers C D Weight (kg)for fan φA
315 408593 65 379 1.0
355 248950 85 423 1.2
400 74880 80 480 1.5
450 248952 95 536 2.0
500 74881 87 600 3.2
560 248953 100 668 4.0
630 74882 108 757 4.8
710 74883 126 857 5.4
800 74884 134 957 6.8
900 404842 150 1077 8.0
1000 74885 167 1199 17.8
Guard – JM Aerofoil
Type I & TypeII
Impeller Side L & S Type
Motor Side S Type
(BT, CT & F22)
Type II guards have a Ø220 hole cut out of centre.
Type III
Motor Side S Type
(D132 & D160)
Type IV
Bellmouth & L Type
Motor Side
Suitable Type C Weightfor fan φA
315 I 137 1.2
315 IV 30 0.5
355 I 137 1.4
355 IV 30 0.5
400 I 137 1.6
400 IV 30 0.6
450 I 137 1.8
450 II 137 1.6
450 IV 30 0.6
500 I 137 2.0
500 II 137 1.8
500 IV 30 0.7
560 I 137 2.2
560 II 137 2.0
560 IV 50 1.0
630 I 137 2.8
630 II 137 2.6
630 III 350 3.0
630 IV 50 1.2
710 I 137 3.2
710 II 137 3.0
710 III 350 3.4
710 IV 50 1.4
800 I 137 3.5
800 II 137 3.3
800 III 350 3.9
800 IV 50 1.5
900 I 137 4.2
900 II 137 4.2
900 III 310 4.8
900 IV 50 1.7
1000 I 137 5.0
1000 II 137 4.8
1000 III 310 5.6
1000 IV 50 2.0
Section
4 - JM
- Accessories
Sec
tion
4 - J
M- Por
tabl
e C
oole
r
116
Aerofoil - JM Portable Cooler Section 4.9
Section
4 - JM
- Portable C
ooler
Sizes
40JM.PC – 400mm, 50JM.PC – 500mm
Fan Performance
The fan uses the JM aerofoil impeller set at maximum pitch for the motor to give maximum cooling velocity.
Impellers
A true aerofoil section high pressure die cast aluminium assembly. All cast aluminium components are X-rayinspected to ensure strength, reliability, performance and safety.
Motors
All motors are totally enclosed with class F insulation. Protection IP55. All motors are supplied with sealed for life bearings.
Electrical Supply
100 - 110 V / 50 Hz / 1 φ220 - 240 V / 50 Hz / 1 φ380 - 420 V / 50 Hz / 3 φ
Temperature Range
-40°C to 50°CFor higher temperatures please enquire.
(All motors are not suitable for starting at temperatures lower than -20°C.)
Casings
Casings are hot dip galvanised with built in conical inlet to ensure performance. The fan is mounted in a heavy duty purpose built tubular frame, a heavy duty isolator is also fitted. Fans are supplied complete with motor side and impeller side safety guards.
• 400mm – 500mm diameter• Air throw, up to 25 m @ 1.25 m/s velocity • Purpose built cradle• Adjustable discharge angle• Aluminium JM aerofoil impeller
• 100% X-ray of impeller• Heavy duty isolator• Motor protection IP55• Motor side and impeller side guards• Casing hot dip galvanised
Sec
tion
4 - J
M- Por
tabl
e C
oole
r
Express Range - These products are available from our UK Express Distributor on same daydelivery from the date of order.
Standard Service - Please consult your local distributor for availability maximum 15 days.
117
Aerofoil - JM Portable Cooler Section 4.9
Performance Data
The performance shown describes the velocity of the air at the distance from the fan.
Sound pressure levels quoted are average dBA at 10m distance over a sphere, under free field conditions and are presented for comparative purposes only.
For details on speed control please enquire.
Electrical Data
100-110V/50Hz/1φ
Product Speed Motor Product Motor Full Load Starting Wiring
Code (rev/min) Number Rating Current Current Diagram
(kW) (at 105V) (at 105V) Ref
(A) (A)
PC40JM 1350 BT9 DPO40028 0.22 4 6 CD1731
380-420V/50Hz/3φ
Product Speed Motor Product Motor Full Load Starting Wiring Sound
Code (rev/min) Number Rating Current Current Diagram Level
(kW) (at 400V) (at 400V) d.o.l. Ref dBA
A) (A)
PC50JM 2910 F22 JP050001 3.8 7.21 64 CD1739 73
Section
4 - JM
- Portable C
ooler
118
Aerofoil - JM Portable Cooler Section 4.9
Dimensions
All dimensions shown in mm
For a full range of accessories including silencers, speed controllers and mountings, please refer to section 4.8 or 9.1 (which shows all accessories)
Wiring diagram references can be found in section 9.2.
Code Motor A B C Weight (kg)
40JM.PC BT9 557 591 649 32
50JM.PC F2225 690 706 890 64