BBS 2216 - Installation Instruction

Ericssonwide InternalINSTALLATION INSTR. 1 ( 14 )

/ XSNHSSG 26/1531-LZA 701 0001 Uen

EAB/ PJR/TP ( Louise Cederlund) 2006-10-18 A

Prepared (also subject responsible if other) No.

Approved Checked Date Rev Reference

Connecting BBS 2216 to RBS 2216

RBS Site Solution

Copyright

Ericsson AB 2006 All Rights Reserved

Disclaimer

No part of this document may be reproduced in any form without the writtenpermission of the copyright owner.

The contents of this document are subject to revision without notice due tocontinued progress in methodology, design and manufacturing. Ericsson shallhave no liability for any error or damage of any kind resulting from the useof this document.

Contents Page

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.1 Documentation .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.2 Tools .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Preparations .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3 Connecting the Battery Power Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Connecting the Communication Link Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5 Connecting the External Alarm Cable .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 Connecting the Transmission Cables (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . 137 Concluding Routines .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147.1 Powering up the RBS ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

A4 XSEIF R4


/ XSNHSSG 26/1531-LZA 701 0001 Uen




1 Introduction

This document describes how to connect Battery Backup System (BBS) 2216to the RBS 2216.

1.1 Documentation

Ensure that the following documents have been read and understood:

Personal Health and Safety Information, 124 46-2885

System Safety Information, 124 46-2886

RBS Installation Instructions, 2/1531-LZA 701 0001

BBS 2216 Installation Instructions, 190 08-EN/LZT 751 0056

DF-OVP Installation Instructions, 190 08-EN/LZT 0040

1.2 Tools

Table 1 Tools Required

Product Description Product NumberTool set Maintenance tool set LTT 601 137/1Tool set 0.54 Nm torque set, which

includes 8 mm open-endedhead for SMA connectors

LTT 601 145/1

2 Preparations

This section describes what to do before starting to connect the power cableand the communication link cable.

To unlock and open the door, do the following:

1. Use the key to unlock the handles on both sides of the RBS.

2. Turn the left-hand handle clockwise while turning the right-hand handleanti-clockwise.

3. Lift and detach the cabinet cover, as shown in the figure below.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




1234P015907A

Figure 1 Cabinet Cover Detachment

4. Connect the Electrostatic Discharge (ESD) wrist strap to the earthgrounding point of the RBS.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




P015911B

Earth grounding point

3M

Figure 2 ESD Wrist Strap Connection Points

5. Switch off all Internal Distribution Module (IDM) circuit breakers.6. Unlock and detach the BBS cover in the same way as the RBS cover

was detached.

7.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




Connect the ESD wrist strap to theearth grounding point of the BBS.

P016665A

Earth grounding point

3M

8. Switch off the main switch of the BBS.

9. Switch off the power to the RBS.

3 Connecting the Battery Power Cable

This section describes how to connect Battery Power Cable from the BatteryFuse Unit (BFU) in the BBS to the IDM in the RBS.Note: Before connecting the power cable, make sure that both the BBS

and RBS are earth grounded. For instructions on handling the earthgrounding connection, see documents RBS Installation Instructionsand BBS 2216 Installation Instructions.

Caution!

Improper handling of batteries can result in the batteries short-circuiting, whichcan result in serious injury due to high energy levels. Exercise the necessarycare when working with batteries.

Note: Make sure that both the AC power and the battery switches are in theOFF position before working with the battery connection.

To route the battery power cable, do the following:

1. Route the cable as shown in the figures below and fasten it in place withcable ties.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




P016560A

RBS 2216

BBS 2216

Power cable

BFU

IDM PSU

Figure 3 Power Cable Routing


/ XSNHSSG 26/1531-LZA 701 0001 Uen




P016561A

Power cable

RBS 2216BBS 2216

BFU

IDM PSU

Figure 4 Power Cable Routing

2.

Connect the power cable connectorto the RBS connector on the BFUin the BBS.

P016562A

Power cable

BFU

RBS

BBS

3.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




Connect the terminals of the powercable to the battery connection onthe IDM in the RBS. See documentRBS installation instructions.

P016563A

IDM

PSU 3 PSzxczaU 4PSU 2PSU 1

DRU 130A

DRU 230A

DRU 330A

DRU 430A

DRU 530A

DRU 630A

DXU 3A

FAN 10ATMA-CM1 3ATMA-CM2 3ALIGHTING 0.5ACLU 11A

Operational

BatteryConnection+24 V DC250A

+24V 0V +24V 0V +24V 0V +24V 0V

RBS

4 Connecting the Communication Link Cable

This section describes how to connect the communication link cable betweenthe BBS and the RBS.

To route the communication link cable, do the following:

1. Route the cable and as shown in the figures below and fasten it in placewith cable ties.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




P016938A

RBS 2216

BBS 2216

Communication link cable

BFU

IDM PSU

Figure 5 Communication Link Cable Routing


/ XSNHSSG 26/1531-LZA 701 0001 Uen




P016939A


RBS 2216BBS 2216

BFU

IDM PSU

Figure 6 Communication Link Cable Routing

2.

Connect one end of the cableto the Power Supply Unit (PSU)connector on the BFU in the BBS.

P016564A


BBS

BFU

RBS

PSU

3.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




Connect the other end of the cableto the A1 connector on the firstPSU from the left in the RBS.

P016565A

RBS PSUA1 connector


5 Connecting the External Alarm Cable

This section describes how to connect the external alarm cable between theBBS and RBS.

To route the external alarm cable, do the following:

1. Route the cable as shown in the figures below and fasten it in place withcable ties.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




P016951A

RBS 2216

BBS 2216

BFU

PSUDXU

External alarms connector

Ext. alarm connector

DF-OVP

Figure 7 External Alarm Cable Routing


/ XSNHSSG 26/1531-LZA 701 0001 Uen




P016952A

RBS 2216BBS 2216

BFU

DXU

DF-OVP

Ext. alarm connector

External alarms connector

Figure 8 External Alarm Cable Routing

2. Strip the insulation from the cable and insert the wires into External Alarmsconnector.

Note: Write down the designation of the wires in the external alarm cable.

3. Connect the external alarm cable to the Distribution Frame withOvervoltage Protection (DF-OVP), and then connect the DF-OVP to theDistribution Switch Unit (DXU) in the RBS. See the DF-OVP InstallationInstructions.

6 Connecting the Transmission Cables (Optional)This section describes how to connect the transmission cables.

To connect the transmission cables, do the following:

1.


/ XSNHSSG 26/1531-LZA 701 0001 Uen




Route the transmission cables on the right-hand side of the BBS and theRBS as shown in the figure below and fasten them in place with cableties.

P015836B

2. Connecting the transmission cable from the transmission equipment to thetransmission ports on the DXU in the RBS. If the BBS and RBS are in adifferent Electromagnetic Compatibility (EMC) environment, DF-OVP isrecommended to be connected between the BBS and the RBS. For detailson how to connect DF-OVP, See DF-OVP Installation Instructions.

7 Concluding Routines

7.1 Powering up the RBS

1. Disconnect the ESD wrist strap.

2. Switch on the power switch outside the cabinet.

3. Switch on the IDM circuit breakers for the units installed in the cabinet.

4. Switch on the RBS switch on the BFU in the BBS.

5. Put back and lock the Cover of BBS.

6. Put back and lock the Cover of RBS cover.

tocConnecting BBS 2216 to RBS 22161 Introduction1.1 Documentation1.2 Tools

2 PreparationsFigure 1 Cabinet Cover DetachmentFigure 2 ESD Wrist Strap Connection Points

3 Connecting the Battery Power CableFigure 3 Power Cable RoutingFigure 4 Power Cable Routing

4 Connecting the Communication Link CableFigure 5 Communication Link Cable RoutingFigure 6 Communication Link Cable Routing

5 Connecting the External Alarm CableFigure 7 External Alarm Cable RoutingFigure 8 External Alarm Cable Routing

6 Connecting the Transmission Cables (Optional)7 Concluding Routines7.1 Powering up the RBS

tablesTable 1 Tools Required

Documents

BBS 2216 - Installation Instruction