Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Assembly Instructions
Land Pride
When you see this symbol, the subsequentinstructions and warnings are serious - followwithout exception. Your life and the lives of others!
depend on it!Before You Start
These assembly instructions contain only information onassembling the BH1560 & BH1575 mounting kit to the BXSeries Kubota Tractor. A detailed Operator’s Manual wassupplied with the main unit when it was purchased. Formore specific information on safety concerns refer to theOperator’s Manual. Also included in the Operator’sManual is important information on operation, adjustment,troubleshooting, and maintenance for this Backhoe (someof these sections do not apply to all options).
© Copyright 2002 Printed 3/13/02
Fig
AB
B
B
A separate Parts Manual for replacement parts can bepurchased from your dealer or downloaded from ourwebsite at www.landpride.com. Have model and serialnumbers handy when placing an order.
Manual Part Numbers:• 340-036M OPERATOR’S MANUAL BH1560/75• 340-036P PARTS MANUAL BH1560/75General InformationThese instructions apply to the Mounting Kit:340-151A FRAME MOUNT & STAB KIT KUB BX
BH1560/75
On page 12 is a detailed listing of parts included in this kit.Use this list as a checklist to inventory parts received.
Assembly Instructions
The following Assembly will be more easily performed ifthe rear tires are removed and the rear of the tractor issafely supported.1. Refer to Figure 1. Remove the three bolts (A) and
lockwashers. These will be used to mount thebrackets in the next step. Remove the three bolts andlockwashers (B). Discard bolts and keep thelockwashers.
BH1560 & BH1575
Kubota BX1800 - BX2200Mounting Kit
1340-300M
ure 1
A
Land Pride
Assembly Instructions
2. Refer to Figure 2. Assemble Left Hand and RightBrackets as shown. Install bolts and lockwashers thatwere removed in Step 1 in locations labeled "B" .
2 BH1560 & BH1575 Mounting Kit 340-300M
Figure 2
B B
B
A
Install supplied bolts and the lockwashers that werekept from Step 1 in locations labeled "A" .
3. Mount rear tires on tractor and place tractor back onground.
3/13/02
Mounting Bracket
A
Land Pride
Assembly Instructions
4. Refer to Figure 3. Remove the lower hitch bracketsthat are currently mounted to the backhoe. Assemblethe brackets supplied in the mounting kit as shown.
3/13/02
Figu
Mounting hardware is supplied with kit or hardwarethat was removed from brackets may be used.
3BH1560 & BH1575 Mounting Kit 340-300M
re 3
Lower Brackets
Land Pride
Assembly Instructions
5. Refer to Figure 4. Place Hydraulic Reservoir U-Boltson Backhoe frame as shown (BH1560 only). For the
4 BH1560 & BH1575 Mounting Kit 340-300M
Figure 4
U-Bolt
BH1575, remove the front valve cover and mount thehydraulic tank in the same holes.
3/13/02
U-Bolt
Land Pride
Assembly Instructions
6. Refer to Figure 5. Assemble Hydraulic Reservoir tothe Backhoe using the U-Bolts placed in Step 4.(BH1560)
3/13/02
Figu
Hydraulic Reservoir
5BH1560 & BH1575 Mounting Kit 340-300M
re 5
Land Pride
Assembly Instructions
7. Assemble PTO Drive adapter to PTO pump as shownin Figure 6.
6 BH1560 & BH1575 Mounting Kit 340-300M
Figure
PTO Drive Adapter
PTO
Figur
PTO Pump
Suc
6
Pump
8. Assemble the Suction Pump Adapter and PressurePump Adapter to the Pump as shown in Figure 7.
3/13/02
e 7
tion Pump Adapter
Pressure Pump Adapter
Land Pride
Assembly Instructions
9. Install Filter Screen and Suction Hose Barb as shownin Figure 8
3/13/02
Figure
Filter Screen
Hose Ba
7BH1560 & BH1575 Mounting Kit 340-300M
8
rb
Land Pride
Assembly Instructions
10. Assemble Suction Hose (Large Hose) end withoutfitting to Hydraulic Reservoir with Hose Clamp.Assemble the end with fitting to the Pump SuctionAdapter.
11. Assemble Elbow Adapter to Hydraulic Reservoirmaking sure that elbow is pointing up.
8 BH1560 & BH1575 Mounting Kit 340-300M
Return (Pressure) Hose
Inlet Hose
Elbow
Oil Rese(Backho
TractSum
Inlet Valve ofBackhoe Valve
Return HoseFrom Backhoe
Valve
Figure
Figure
12. Disconnect hose from inlet side of valve and connectto Elbow on Hydraulic Reservoir.
13. Disconnect Return Hose (Pressure) and connect toPressure Adapter on Pump.
3/13/02
Suction Hose
Hose Clamp
Pump
Suction Filter
rvoire ororp)
Press.
Tank
9
10
Land Pride
Assembly Instructions
14. Assemble torque bar to Pump with 3/8" bolts andlocknuts as shown.
15. Back tractor up to backhoe just close enough toassemble the Pump to tractor’s PTO drive shaft. Donot back completely up to backhoe. Leave some room
3/13/02
Figu
PTO Pump
for PTO pump and assembly. The Pump should beassembled so that the Torque Bar is pointing up.
16. Set lower 3-point arms 9" from ground to center ofswivel ball, then back the tractor until lower 3-pointalign with lower mounting brackets on the backhoethen attach accordingly.
9BH1560 & BH1575 Mounting Kit 340-300M
re 11
Torque Bar
3/8" Bolts & Locknuts
Land Pride
Assembly Instructions
17. Align tractor’s lower 3-point arms and locking bar withthe bottom holes of backhoe’s lower 3-point brackets.The locking bar will be beneath the lower 3-pointarms. Install pins and secure with lynch pins. Align the
10 BH1560 & BH1575 Mounting Kit 340-300M
Figure 1
Pins
Lock Pins
locking bar’s eyebolts with the top holes of theBackhoes 3-point brackets. Install pins and securewith lock pins. There may be some adjustment of theeyebolts to align with the top holes.
3/13/02
2
Locking Bar
Eyebolt
Adjustment Nuts
3-Point Arms Above Locking Bar
Land Pride
Assembly Instructions
Frame Stabilizer Bar Assembly1. Place the Stabilizer Bar between the frame to make
sure it will fit. The Stabilizer Bar end plates might needto be tweaked so that it fits between the frame asshown.
2. Assemble the two hole plate to the threaded hole ofthe Stabilizer Bar as shown capturing the framebetween the Bar and the two hole plate.
3/13/02
Figure
Stab
Bolt, flat washer, lockwasher and nut
One hole plate
3. Place the flat washer on the bolt and insert it throughthe top hole of two hole plate, through the hole in thetractor frame and through the top hole of the StabilizerBar.
4. Assemble the one hole plate to the other end of theStabilizer Bar, capturing the tractor frame between thebar and the plate.
13
ilizer Bar
Bolt
Two hole plate
Disassembly1. Lower bucket & stabilizers to the ground to get a
sturdy base before any pin or pump removal.2. Disconnect the Pump from the tractor’s PTO shaft.
3. Disassemble the locking bar completely. Top link and/or stabilizer need to be unpinned before removingbackhoe.
4. Drive away from Backhoe.
11BH1560 & BH1575 Mounting Kit 340-300M
Land Pride
Listing of Parts
BH1560 & BH1575 Mounting Kit 340-300M 3/13/0212
340-151A FRAME MOUNT & STAB. KIT KUB BX BH1560/75Your Kit Includes:
1 340-053K 3 PT STABILIZER KIT BH1575
Qty. Part No. Part Description
5 839-526C 1/4" LINCH PIN BH STABILIZE2 839-528C ADJ.STABILIZER LINK CAT1 BH5 839-529C PIN,3/4X4 1/2 W/LOOP BH
Qty. Part No. Part Description
1 340-293K FRME MNT KUB BX 1560
Qty. Part No. Part Description
1 340-022D WASHER W/1 HOLE 3/8X3SQ.1 340-023D WASHER W/2 HOLE 3/8X2X3 3/41 340-303H FRAME MOUNT BRKT RH BX18/221 340-304H FRAME MOUNT BRKT LH BX18/221 340-305H CROSSTUBE WELDMT BX18/221 340-306H SPCL LWR LINK BRKT RH BX18/221 340-306H SPCL LWR LINK BRKT LH BX18/228 802-055C HHCS 5/8-11X2 GR52 802-184C HHCS 3/4-10X1 1/2 GR58 803-024C NUT LOCK 5/8-11 PLT8 804-019C WASHER FLAT 5/8 USS PLT2 804-023C WASHER LOCK SPRING 3/4 PLT13 804-076C WASHER LOCK 9/16 PLT3 839-526C 1/4" LINCH PIN BH STABILIZE1 839-529C PIN,3/4X4 1/2 W/LOOP BH2 839-659C PIN LOWER HITCH 7/8X3 1/2 839-828C PIN HITCH 1X5 3/4 CAT II 256 839-943C CAPSCREW 14MMX1.5MMX50MM3 839-944C CAPSCREW 9/16-12X1 3/42 839-945C PIN CLEVIS 3/4X3 1/22 839-946C FITTING ADAPTOR C5205X6X61 839-947C HOSE 3/8X1/2MALEX9/16JICFX71 839-948C HOSE 3/8X1/2MALEX9/16JICFX61 839-949C NUT HEX 9/16-12
Qty. Part No. Part Description