Bidding Document for - Uttarakhandujs.uk.gov.in/files/TenderFiles/ADB_Volume-II-_format... · 2014-06-12 · Bidding Document for Supply, Laying, Jointing, Testing and Commissioning

Government of Uttarakhand

Uttarakhand Emergency Assistance Project

[ADB Loan No. 3055 IND]

Bidding Document for

Supply, Laying, Jointing, Testing and Commissioning of Water Transmission Mains and Design, Supply, Construction and Commissioning of Infiltration

Wells, WTP, GLSR etc. At Rudraprayag, Karnprayag, Gauchar, Uttarkashi and Devprayag

Contract Package No. UK/UEAP-UJS/WSS-GW/01

(Single Stage Two Envelope Bidding Procedure)

Under

National Competitive Bidding (NCB)

Volume 2- Price Bid

Invitation for Bid No. : UEAP-UK/NCB/02/2014-15 Date of Issue: 27.05.2014 Employer: State Disaster Management Authority (SDMA), Government of Uttarakhand, Represented by

The Program Manager, Program Implementation Unit (PIU), Uttarakhand Jal Sansthan

Country: India

May 2014

Section 4 B– Bidding Forms Package No. UK/UEAP-UJS/WSS-GW/01

Supply, Laying, Jointing of Transmission Mains and Design, Construction of Infiltration Well, WTP and GLSR etc. ______ Page 1 of 135

Section 4 B – Bidding Forms This Section contains the Form which are to be completed by the Bidder and submitted as part of his bid



Letter of Price Bid

Date

NCB No.- UEAP-UK/NCB/02/2014-15

Contract Package No. – UK/UEAP-UJS/WSS-GW/01

To: Program Manager,

Program Implementation Unit, UEAP

Uttarakhand Jal Sansthan, Jal Bhawan,

B-Block , Nehru Colony, Dehradun- 248001

Tel/Fax: No +91-135 – 2676260/2676177; Email: [email protected]

We, the undersigned, declare that:

(a) We have examined and have no reservation to the Bidding Documents, including Addenda issued in accordance with Instructions to Bidders (ITB), Clause 8:

(b) We offer to execute in conformity with the Bidding Documents the following Works:

“Supply, Laying, Jointing, Testing and Commissioning of Water Transmission Mains and Design, Supply, Construction and Commissioning of Infiltration Wells, WTP, GLSR etc. at Rudraprayag, Karnprayag, Gauchar, Uttarkashi and Devprayag”

(c) The total price of our Bid, excluding any discounts offered in item (d) below is:………………

(d) The discounts offered and the methodology for their application

are:……………………….

(e) Our Bid shall be valid for a period of 120 days from the date fixed for the bid submission deadline in accordance with the Bidding Documents, and it shall remain binding upon us and may be accepted at any time before the expiration of that period:

(f) If our Bid is accepted, we commit to obtain a performance security in accordance

with the Bidding Documents:

(g) We have paid, or will pay the following commissions, gratuities, or fees with respect to the bidding process or execution of the contract:



Name of Recipient Address Reason Amount

(h) We understand that this bid, together with your written acceptance thereof included in

your notification of award, shall constitute a binding contract between us, unit a format contract is prepared and executed: and

(i) We understand that you are not bound to accept the lowest evaluated bid or any

other bid that you may receive. (j) We agree to permit ADB or its representative to inspect our accounts and records

and other documents relating to the bid submission and to have them by auditions appointed by ADB.

(k)

If awarded the contract, the person named below shall act as Contractor’s Representative

Name……………………………………………………………………………………………… In the capacity of………………………………………………………………………………… Signed…………………………………………………………………………………………… Duly authorized to sign the Bid for and on behalf of ……………………………………….. Date………………………………………………………………………………………………

• “If none has been paid or is to be paid, indicate “none”



Tables of Adjustment Data Table A- Local Currency

Index Code

Index Description Source of Index

Base Value and Date

Bidder’s Local Currency Amount

Bidder’s Proposed Weighting

Nonadjustable (a)

-------- -------- -------- a: 0.25

Labour (b) General Index: Consumer Price Index for Industrial Workers

Reserve Bank of India

As on 28 days prior to the deadline for bid submission

As per cost of work

b: 0.25

Cement (c) Wholesale Price Index for Grey Cement



As per cost of work

d: 0.20

Steel (d) Wholesale Price Index of average of Long & Flat steel



As per cost of work

c: 0.20

Bitumen (e) Ex-factory price at Panipat Refinery



As per cost of work

e: 0.05

Other Material (f) All Commodities: Wholesale Price Index by Groups and Subgroups



As per cost of work

f: 0.05

Total 1.00



Schedule of Payment Currencies For Supply, Laying, Jointing, Testing and Commissioning of Water Transmission Mains and Design, Supply, Construction and Commissioning of Infiltration Wells, WTP, GLSR etc. at Rudraprayag, Karnprayag, Gauchar, Uttarkashi and Devprayag Package No. UK/UEAP-UJS/WSS-GW/01

A B C D

Name of Payment Currency

Amount of Currency

Rate of Exchange to Local Currency

Local Currency Equivalent C = A x B

Percentage of Net Bid Price (NBP) 100xC NBP

Local currency

1.00

100.00

Provisional Sums Expressed in Local Currency

1.00

Bid Price



Bill of Quantities

Preamble to Bill of Quantities

1. The Bill of Quantities shall be read in conjunction with Instructions to Bidders

General and Particular Conditions of Contract, Technical Specifications, and Drawings.

2. The quantities given in the Bill of Quantities are estimated and provisional, and are given to provide a common basis for bidding. The basis of payment will be the actual quantities of work ordered and carried out, as measured and verified by the Engineer and valued at the rates and prices bid in the priced Bill of Quantities, wherever applicable, and otherwise at such rates and prices as the Engineer may fix within the terms of the Contract.

3. The rates and price bid in the priced Bill of Quantities shall except as otherwise provided under the Contract, include all required construction equipment, labour, supervision, materials, erection, maintenance, insurance, profit, taxes and duties together with all general risks, liabilities, and obligations set out or implied in the contract.

4. A rate or price shall be entered against each item in the priced Bill of Quantities. The cost of Items against which the Contractor has failed to enter a rate or price shall be deemed to be covered by other item rates and prices entered in the Bill of Quantities.

5. The whole cost of complying with the provisions of the Contract shall be included in the Items provided in the priced Bill of Quantities, and where no Items are provided, the cost shall be deemed to be distributed among the rates and prices entered for the related Items of Work.

6. General directions and descriptions of work and materials are not necessarily repeated nor summarized in the Bill of Quantities. References to the relevant sections of the Contract documentation shall be made before entering prices against each item in the priced Bill of Quantities.

7. Provisional Sums included and so designated in the Bill of Quantities shall be expended in whole or in part at the direction and discretion of the Engineer in accordance with the Conditions of Contract. It will be used by the Engineer for nominated sub-contractors, line agencies, third party inspecting agencies, charges levied by statutory electrical, telephone, or other authorities, or for other miscellaneous works. The use of provisional sum will also be for relocation of utilities above or under the ground that conflict with the existing or permanent line or level or the works; independent sampling and laboratory testing as directed by the Engineer, Replacement or Compensation for Plants and Trees removed due to the works; Permanent reinstatement of asphalt roads etc. as directed by the Engineer.

8. The method of measurement of completed work for payment shall be in accordance with the relevant codes of practice. .

9. Rock is defined as all materials that, in the opinion of the Engineer, require blasting, or the Use of metal wedges and sledge hammers, or the use of compressed air drilling for their removal etc.



10. Cost of temporary works like Construction and maintenance of road diversions

including traffic control; Construction and maintenance of temporary dewatering and drainage arrangements, establishment and. maintenance of contractor's site office, store, establishment and maintenance of workshops, plant and equipment, including Project sign boards etc will be part of work and shall not be paid extra.

11. Drawings and designs provided are for reference only. They may be modified

according to site conditions.



Abstract of Bid Price (Package: UK/UEAP-UJS/WSS-GW/01)

Name of Bidder……………………………………………………………………………………

SI Item Amount (Rs.)

1 Sub-total of Schedule A

2 Sub-total of Schedule B

3 Sub-total of Schedule C

4 Sub-total of Schedule D

5 Sub-total of Schedule E

6 Provisional Sum INR 32,740,000

Sub Total

Currency of the amount quoted is in accordance with ITB Clause 15 Name of Bidder ………………………… In the capacity of……………………………. Signature of Bidder ………………………… Duly authorized to sign the Bid for and on behalf of………………………………… Date…………………………………………..


Supply, Laying, Jointing of Transmission Mains and Design, Construction of Infiltration Well, WTP and GLSR etc. Page 8 of 135

Schedule No. A (Rudraprayag) Schedule No. A1 – Rehabilitation and Augmentation of Water Supply Scheme in Rudraprayag Town

Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

Earthwork

1

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lifts upto 1.5m, including getting out the excavated soil as directed by Engineer with all lead and lift including danger lighting and using sight rails and boring rods at every 100 m wherever necessary including the cost of labour, tools and plants and any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge

1.1 All kinds of soil Cum 1280

2

Backfilling with available excavated earth (excluding rock) in pipe trenches, plinth side, foundation of valves or any other structure in layers not exceeding 20 cm in depth, consolidating each deposited layers by ramming and watering with all lead and lift and depth upto 1.5 m including the cost of labours, tools and plants, water or any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge.

Cum 1000

Pipeline Laying Work



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

3 Supply of 200mm dia 6mm thk MS-ERW pipe (FE-410 grade) conforming to IS 3589:2001 and as per specification.

Rmt 2000

3.1

Laying & jointing of 200mm dia 6mm thk Mild Steel pipes (FE-410 grade) conforming to IS 3589:2001 and Mild steel specials (bends, tees, tapers etc) confirming to IS 7322 including perfect linking and welding of joints to correct position including cost and conveyance of pipes and materials with all lead and lifts, cost of labour and giving satisfactory hydraulic test as per IS 3589:2001 with water supplied at the cost of the contractor for test pressure and working pressure both at factory and site etc. and including the cost of ultrasonic / radiographic test as per relevant IS, complete as per detailed specification with liquid epoxy coating for internal & external surface of the pipeline as per clause 16.1 of ANNEX B as per IS 3589:2001 (latest revision) including loading and unloading of pipes for the required clear internal diameter before coating and specified thickness of plate as mentioned, complete as per detailed specifications and as directed by the Engineer.

Rmt 2000

4

Supplying, Laying & Jointing of G.I. Pipes confirming to IS:1239 (latest Edition) complete with G.I. fittings including trenching and refilling, laying the pipe true to alignment, including cutting and threading of pipe for making up lengths as required for proper completion of work, cost of all materials with all lead and lifts, cost of labour and giving satisfactory hydraulic test, etc. as per



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

specifications and directions of Engineer-in-charge.

4.1 25 mm GI pipe for Distribution pipeline (Medium duty Class)

Rmt 300


Rmt 300


Rmt 300


Rmt 2250


Rmt 600


Rmt 250

5

Supplying, Laying and Jointing of brand new VAG EKO or equivalent make DI sluice valve conforming to IS 14846 with latest amendments with all lead and lift complete as per specifications and fixing and jointing of DI Sluice valves true to line and gradient, including cost of DI/MS specials, MS specials can be provided only if DI specials are not available (tail pieces, dismantling joints, puddle flanges, flanges, etc.) for the specified diameters including cost of jointing materials like bolts, nuts, rubber insertions, labour, testing, etc complete as per drawing and as directed by the Engineer.

5.1 80 mm dia PN 1.6 Sluice valve for 80mm Pipe No. 2

5.2 200 mm dia PN 1.6 Sluice valve for 200 mm Pipe No. 2



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

6

Supply, Laying and Jointing of brand new DI kinetic Double Orifice Air valve approved by the Engineer having small elastic ball resting on gun metal orifice nipple and large orifice vulcanite ball seating ring with built-in kinetic features and rating of PN 1.0 with isolating DI sluice valve of PN 1.0 rating having body, door, dome, gland, non rising stainless spindle, Flanges drilled to IS:1538, valves tested by closed method, mounted in a horizontal position, and operated by metre wheel gearing of approved quality with bolts, nuts, rubber insertions, labour etc. complete. as per drawing and as directed by the Engineer.

6.1 80 mm dia Air Valve No. 2

7

Supplying, Laying and Jointing DI Scour valve 200mm PN 1.0 conforming to IS 14846 with latest amendments with all lead and lift complete as per specifications and fixing and jointing of DI Sluice valves true to line and gradient, including cost of DI / MS specials (tail pieces, Tees, dismantling joints, puddle flanges, flanges, duck foot bend, bend, semicircular bend), for the specified diameters including cost of jointing materials like bolts, nuts, rubber insertions, labour, testing etc., complete as per drawing and as per detailed specifications and as directed by the Engineer Incharge.

No. 2



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

8

Supply and fixing of brand new Bulk Water Meter (Woltmann type cold water meter) 200mm dia of approved make having facility to incorporate RF based wireless remote transreceivers for automatic meter reading. The water meters shall be with removable mechanism, magnetic drive, dry dial, hermetically sealed register, class B type, manufactured in accordance with ISO-4064 standards or equivalent. The meter body shall be flanged end for connection and the bolt hole drilling shall be as per IS 1538. The meter body shall be cast iron as per IS 210 Gr FG260 and shall be coated with a high quality fusion bonded powder coating inside and outside the meter body. The meters shall be equipped with a suitable strainer for longer life of the meter. The meters performance specifications shall be EEC/ISO-4064 Class-B performance. Accuracy shall be in accordance with ISO & EEC class B. The meter shall be suitable to work at working pressure of 16 Bar & temperature of 45oC. The meter shall be preequipped for SCADA and suitable communication including CI Sluice valve IVC/ IVI / KBL / R & D/ Kejriwal make as per IS 14846 with latest amendments for Control and cost of specials (puddle flanges, flanged tail piece, Dismantling joint and flanges & necessary reducer and enlargers to fix the Bulk Meters) and jointing materials complete with all lead and lift and as per detailed specifications and as directed by the Engineer Incharge.

No. 1



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

9 Providing RCC Chambers of required specifications as per drawings and as directed by the Engineer Incharge for Intake works and Valve chambers

No. 8

Restoration of Gravity Sources



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

10

Supply of Mild Steel Uttaranchal Koop Cylindrical type made from ERW Mild Steel tubes Grade Fe-410 to withstand minimum pressure of 7 MPa and generally as per specification no : 4270 (First Revision) (with latest amendments) duly screwed. Low Carbon Galvanized/ Stainless Steel Grade SS 304 Laterals should be designed as per IS: 8110-2000 having slot size 1.0 mm with 40% open area. One end of the lateral will be duly screwed and other end will be duly closed as shown in the drawing. Overall length of Uttaranchal Koop should be 1250 mm inclusive of MS Blank Flange and MS Jali. At inlet near 8 cm from one end of MS ERW pipe in cross position horizontal direction plugged with GI Socket duly threaded to accommodate suitably lateral pipe without any leakage. Top end of MS ERW pipe plugged with MS blank Flange, 5 mm thick fitted with nut, bolt and washer, one number socket fitted for outlet near 59 cm from blank flange at surface of MS ERW pipe along with one number GI Bend of 11.25deg, a jali of 10mm square bar to be fitted into internal portion of ERW pipe near bottom end. Painting with two coat of anti corrosive red oxide paint including all nut bolts and washers complete. All electrically welded joints should be water tight.

No

3



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

10.1 Installing and commissioning of Uttaranchal Koop as per specifications and as per drawings at required locations. No 3

Bridge Work (Pipeline Protection)

11

Providing and laying Reinforced cement Concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:

11.1 1:1½:3 (1 Cement : 1½ coarse sand :3 graded stone aggregate 20 mm nominal size)

11.1.1 For Top Slab cum 2.40

11.1.2 For Column / Pedestal cum 2.70

11.1.3 For Footing of Column cum 7.20

11.2 Providing Centering and Shuttering works for RCC work at different locations.

sqm 90

11.3

Providing, supplying and fabricating of reinforcement of all sizes including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position, tieing with binding wire of approved quality and gauge including the cost of binding wire and anchoring to adjoining members wherever necessary including all laps and wastages etc., with all lead and lifts, complete as per design, specification and as directed by the Engineer.

11.3.1 For Column / Pedestal and Footing kg 1100.00

11.3.2 For Top slab kg 240



Unit Rate (INR)

Item No

Description

Unit

Quantity In Figures

In Words

Amount

(INR)

PCC Work

12

Providing and laying cement concrete of 1:3:6 grade using approved hard aggregate for PCC using 20 mm and down size aggregate including mixing, laying, tamping, curing and finished for exposed faces including cost of labours, material, tools and plants, curing and any other item require for the completeness of work in all respect complete with all lead and lifts, as per specification and as directed by the Engineer-incharge. (for pipe encasing, valve chambers or any other similar structure)

cum 10

13

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of RCC Framed structure (Normal Building) floor height 3.35 mtr. for Office Building as per specification for area atleast 200sqm for office building (G+1)

sqm 200

14

Dismantling old Existing damaged office Building, manually/ by mechanical means including stacking of Steel bars and disposal of unserviceable items by mechanical means, including loading, transporting, unloading to approved municipal dumping ground for all lead and lift as per specifications and as directed by Engineer-in-charge

cum 100

To be carried forward to Grand Summary Name of Bidder

Signature of Bidder



Schedule No. A2 – Environmental Management & Monitoring (Rudraprayag)

Unit Rate (INR) Item Description Unit Qty.

In Figures In Words Amount (INR)

A Legislation, permits and Agreements

B Public Consultations and information Disclosure

Lump sum 1

C Environmental Baseline Data Generation

1 Ambient Air Quality Monitoring

Per Sample 5

2 Noise Quality Monitoring Per Sample 5

3 Water Quality Monitoring Per Sample 4

4 Soil Per Sample 12

5 Dust Suppression at subproject sites

Lump sum 1

D Environmental Monitoring

1 Air Quality (Construction)

Per Sample (5 No. of Location x 3 seasons in year 1 sample per location) for 1.5 year

23

2 Water Quality (Construction)


18





3 Noise Levels (Construction)

Per Location (5 No. of Location x 3 seasons in year 1 sample per location) for 1.5 year

23

4 Soil (Construction)


54

5 Ambient Air Quality (Operation/Defect Liability Period)

Per Sample 15

6 Water Quality (Operation/Defect Liability Period)

Per Year 15

7 Ambient Noise Quality(Operation/Defect Liability Period)

Per Sample 12

To be carried forward to Grand Summary

Name of Bidder

Signature of Bidder



Schedule No. B (Karnaprayag) Schedule No - B1- Rehabilitation and Augmentation of Water Supply Scheme in Karnaprayag Town

Unit Rate (INR) Item No

Description Unit Quantity In Figures In Words

Amount (INR)

1 Infiltration Well and Pump House

Soil investigation, conducting SBC and infiltration rate test, Design, supply, construction, testing, commissioning of infiltration well of 2.46 MLD and construction of Pump House above infiltration well at Alaknanda River site, clearing, grading, including but not limiting the specification mentioned in Section -6- Employers Requirements of the Bid Documents including fixing crane for lifting pumps including supply of all materials, labour, tools, plants and other equipments or any other item required for the proper completion of work in all respect as per specification as directed by the Engineer with approach bridge, all lead, lift, diversion of flow and dewatering of water etc. complete (On Lump sum Basis)

No. 1

2

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of Sump of capacity 100KL or more as per specification and directions of engineer-in-charge.

L.S. 1

3

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of pump house of atleast 20 Sq.m. area or more for HSCF pumps as per the requirement of pump

Sq.m 20





Amount (INR)

installation including fixing crane for lifting pumps as per specification and directions of engineer-in-charge.

4

Supplying, erecting, testing and commissioning of Submersible type Pumpset of capacity 1410 LPM (minimum) with pumping head of 20 meters and lowering upto a depth of 20 meter minimum including all required piping upto floor level of Pump house for Infiltration Well including all materials, specials, labour, machineries for erection, lowering of pumpsets with all transportation etc., as per specification and as directed by the Engineer.

No. 2

5

Supplying, erecting, testing and commissioning of Horizontal Centrifugal type Pumpsets of capacity 1410 LPM (minimum) with pumping head of 237 meters including all required piping from Sump to Pump house and within Pump house including all materials, specials, labour, machineries for erection, lowering of pumpsets with all transportation etc., as per specification and as directed by the Engineer.

No. 2

6 Pipeline Work

6.1

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lifts upto 1.5m, including getting out the excavated soil as directed by Engineer with all lead and lift





Amount (INR)

including danger lighting and using sight rails and boring rods at every 100 m wherever necessary including the cost of labour, tools and plants and any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge.

6.1.1 All Kinds of Soil Cum 3305

6.2


cum 3116

6.3 Supply of 200mm dia 6mm thk MS-ERW pipe (FE-410 grade) conforming to IS 3589:2001 and as per specification.

Rmt 6000

6.4

Laying & jointing of 200mm dia 6mm thk Mild Steel pipes (FE-410 grade) conforming to IS 3589:2001 and Mild steel specials (bends, tees, tapers etc) confirming to IS 7322 including perfect linking and welding of joints to correct position including cost and conveyance of pipes and materials with all lead and lifts, cost of labour and giving satisfactory hydraulic test as per IS 3589:2001 with water supplied at the cost of the

Rmt 6000





Amount (INR)

contractor for test pressure and working pressure both at factory and site etc. and including the cost of ultrasonic / radiographic test as per relevant IS, complete as per detailed specification with liquid epoxy coating for internal & external surface of the pipeline as per clause 16.1 of ANNEX B as per IS 3589:2001 (latest revision) including loading and unloading of pipes for the required clear internal diameter before coating and specified thickness of plate as mentioned, complete as per detailed specifications and as directed by the Engineer.

6.5

Supplying, Laying & Jointing of G.I. Pipes confirming to IS:1239 (latest Edition) complete with G.I. fittings including trenching and refilling, laying the pipe true to alignment, including cutting and threading of pipe for making up lengths as required for proper completion of work, cost of all materials with all lead and lifts, cost of labour and giving satisfactory hydraulic test, etc. as per specifications and directions of Engineer-in-charge.

6.5.1 25 mm GI pipe for Distribution pipeline (Medium Class)

Rmt 100


Rmt 250


Rmt 1675


Rmt 1125





Amount (INR)


Rmt 150


Rmt 4450

6.6


6.6.1 200 mm dia PN 1.6 Sluice valve for 200 mm Pipe No. 2

6.7

Supplying, Laying and Jointing DI Scour valve 200mm conforming to IS 14846 with latest amendments with all lead and lift complete as per specifications and fixing and jointing of DI Sluice valves true to line and gradient, including cost of DI / MS specials (tail pieces, Tees, dismantling joints, puddle flanges, flanges, duck foot bend, bend, semicircular bend), for the specified diameters including cost of jointing materials like bolts, nuts, rubber insertions, labour, testing etc., complete as per drawing and as per detailed specifications and as directed by the Engineer

No. 4





Amount (INR)

Incharge.

6.8

Supply, Laying and Jointing of brand new DI kinetic Double Orifice Air valve approved by the Engineer having small elastic ball resting on gun metal orifice nipple and large orifice vulcanite ball seating ring with built-in kinetic features and rating of PN 1.0 with isolating DI sluice valve of PN 1.0 rating having body, door, dome, gland, non rising stainless spindle, Flanges drilled to IS:1538, valves tested by closed method, mounted in a horizontal position, and operated by metre wheel gearing of approved quality with bolts, nuts, rubber insertions, labour etc. complete as per drawing and as directed by the Engineer.

6.8.1 80 mm dia Air Valve No. 11

6.9

Supply and fixing of brand new Bulk Water Meter (Woltmann type cold water meter) 200mm dia of approved make having facility to incorporate RF based wireless remote transreceivers for automatic meter reading. The water meters shall be with removable mechanism, magnetic drive, dry dial, hermetically sealed register, class B type, manufactured in accordance with ISO-4064 standards or equivalent. The meter body shall be flanged end for connection and the bolt hole drilling shall be as per IS 1538. The meter body shall be cast iron as per IS 210 Gr FG260 and shall be coated with a high quality fusion bonded powder coating inside and outside the meter

No. 1





Amount (INR)

body. The meters shall be equipped with a suitable strainer for longer life of the meter. The meters performance specifications shall be EEC/ISO-4064 Class-B performance. Accuracy shall be in accordance with ISO & EEC class B. The meter shall be suitable to work at working pressure of 16 Bar & temperature of 45oC. The meter shall be preequipped for SCADA and suitable communication including CI Sluice valve IVC/ IVI / KBL / R & D/ Kejriwal make as per IS 14846 with latest amendments for Control and cost of specials (puddle flanges, flanged tail piece, Dismantling joint and flanges & necessary reducer and enlargers to fix the Bulk Meters) and jointing materials complete with all lead and lift and as per detailed specifications and as directed by the Engineer Incharge.

6.10

Providing RCC Chambers of required specifications as per drawings and as directed by the Engineer Incharge for Sluice valves, Air valves and Scour valves, Source rehabilitation etc.

No. 25

7 RCC Structure for Stream Crossing

7.1

Providing and laying Reinforced cement Concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:





Amount (INR)

1:1½:3 (1 Cement : 1½ coarse sand :3 graded stone aggregate 20 mm nominal size)

7.1.1 For Top Slab Cum 4.80

7.1.2 For Column / Pedestal Cum 10.68

7.1.3 For Footing of Column Cum 14.40

7.2 Providing Centering and Shuttering works for RCC work at different locations.

Sq. m. 180.00

7.3

Providing, supplying and fabricating of reinforcement of all sizes including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position, tieing with binding wire of approved quality and gauge including the cost of binding wire and anchoring to adjoining members wherever necessary including all laps and wastages etc., with all lead and lifts, complete as per design, specification and as directed by the Engineer.

7.3.1 For Column / Pedestal and Footing Kg 3260.40

7.3.2 For Top slab Kg 480.00

8 Site Protection Works

8.1

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc up to floor five level, excluding the cost of centering, shuttering and finishing:





Amount (INR)

8.1.1 1:2:4 (1 Cement : 2 Coarse sand : 4 graded stone aggregate 40 mm nominal size)

Cum 97

8.1.2 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Cum 872

8.2 Providing Centering and Shuttering works for RCC work at different locations

Sq.m. 1050

8.3

Providing, supplying and fabricating of reinforcement using TMT bars of all sizes including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position, tieing with binding wire of approved quality and gauge including the cost of binding wire and anchoring to adjoining members wherever necessary including all laps and wastages etc., with all lead and lifts, complete as per design, specification and as directed by the Engineer at different locations

Kg 76022

9

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of Clear water Reservoir as per required design using RCC construction with all necessary arrangements, water level indicator etc all complete as per drawing and as directed by the Engineer.

9.1 500KL at ITI Colony LS 1

9.2 35KL at taxi Stand LS 1

9.3 150KL at taxi Stand LS 1





Amount (INR)

10

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning RCC Framed structure (Normal Building) floor height 3.35 mtr. for Office Building as per specification for area atleast 200sqm for Office building (G+1)

Sq. m. 200

11

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of RCC framed structure for Transformer Room as per specification for area of 24sqm.

Sq. m. 24

12


Cum 100


Name of Bidder

Signature of Bidder



Schedule No. B2 - Electrical and Automation works (Karnaprayag)

Unit Rate (INR) S. N. DESCRIPTION Unit QTY


Medium Voltage Primary Supply

1

Design, Supply, Receiving, Storing, Inspection, Handling, Assembling, Installing in correct aligned position, 11 kV, 22.6 kA/1SEC, 100A outdoor type, approved make, Air break switch (ABS) with Earth switch, power contact position indicator, padlocking facility, auxiliary contacts and all other accessories for satisfactory operation as per detail specification, in conformance with IS:9921, as required by the statutory electrical authorities guidelines and as per reference 11kV Single Line Dwg. GW/01/KP-E-018

L.S. 1

2

Design, Supply, Receiving, Storing, Inspection, Handling, Assembling, Installing in correct aligned position, effecting proper Connections, Testing and Commissioning of 11KV, 630amp., VCB Panel as per specifications suitable for 1 Run of 3C x 50 sq. mm. Aluminium conductor armoured cable for Incoming and outgoing termination.

L.S. 1

3

Design, Supply, Receiving, Storing, Inspection, Handling, Assembling, Installing in correct aligned position, effecting proper Connections, Testing and Commissioning of 11kV/0.433 kV, 3 Phase, 50Hz, 400 kVA, ONAN cooled, mineral Oil filled, Dyn11, copper wound, approved make, transformer having + 5 % to -15 % On Load Tap Changer, cable box on 11kV side suitable for 1 Run of 3C x 240 sq. mm. Aluminium conductor armoured cable and cable box on secondary side suitable for 2R x 3.5C x 240 sq.

L.S. 1





mm. XLPE, Aluminium conductor armoured cables. Transformer shall be provided with all the accessories and fittings conforming to IS 2026 (Part I-IV), Energy Conservation Building code (ECBC), IS 6600 with its latest amendments and as per approved data sheet.

4

Design, Supply, Laying, Tieing, Tagging, Testing and Commissioning of 3 core, 50 sq. mm. 11 kV, 22.6 kA, XLPE insulated, FRLS sheathed, Aluminium conductor, armoured cable in constructed cable trench confirming to IS 7098 with its latest amendments and as per approved make. (From 11 kV Lightning arrestor to 11 kV Air Break Switch (ABS) Panel and from ABS panel to individual Distribution Transformer) Note: Each run of cable will be measured separately and paid.

Rmt 60

5

Design, Supply, Termination and Commissioning of Raychem HV Indoor type heat shrinkable termination kit of approved make complete with all accessories suitable for 3 core 50 sq. mm., 11 kV, XLPE insulated, FRLS sheathed, aluminium conductor armoured cable. It shall withstand the range of ambient temperature experienced in Karnprayag.

No 4

LV Power distribution and Motor Control Centre

1 Design, Supply, Installation, Testing and commissioning of LT Power distribution board for Mains supplies distribution as per specifications

No 1

2 Design, Supply, Installation, Testing and commissioning of Lighting Distribution Boards for

No 2





Indoor and Outdoor lighting and auxiliaries.

3

Design, Supply, Installation, Testing and commissioning of SCADA compatible Motor control centre as per specifications for RBF I- WELL water pumping suitable for 2*7.5 KW pumps

No 1

4

Design, Supply, Installation, Testing and commissioning of SCADA compatible Motor control centre as per specifications for Clear water pumping suitable for 2*132 KW pumps

No 1

5

Design, Supply and laying of Power cables with Tray/clamped to wall with suitable clamps, saddles and fixing bolts/ in ground including the cost of digging and backfilling with sand and brick protection as required and including testing and commissioning of the following sizes of 1.1kV grade multi core aluminium conductor XLPE insulated and FRLS sheathed armoured cable conforming to IS: 7098 (Part-I) with latest amendments. The costs shall include properly clamping with cable clamps, terminal lugs and ties. Identification tags shall be provided for all cables.

L.S. 1

3.5C x 400 sq. mm. As per site



3C x 70 sq. mm. As per site



Automation, SCADA and instrumentation





A MASTER CONTROL STATION AT DEHRADUN

(a)

Design, Supply, installation, testing and Commissioning of water management SCADA software including screen development, report development with SQL server base & necessary associated software as detailed in specifications sheet.

L.S. 1

(b)

Design, Supply, Installation, Testing and commissioning of GSM-GPRS Modem bank for Telemetry Communication system with power supply & communication cable etc.

L.S. 1

(c) Design, Supply and Installation of 1 PC, 1 UPS, 1Printer

L.S. 1

B LOCAL CONTROL STATION AT KARNPRAYAG

(a)

Design, Supply, installation, testing and Commissioning of water management SCADA software including screen development, report development with SQL server base & necessary associated software as detailed in specifications

L.S. 1

(c)

Design, Supply, Installation, Testing and commissioning of Modem bank for Telemetry Communication system with power supply & communication cable etc.

L.S. 1

(d) Design, Supply and Installation of 1PC, 1 KVA UPS, 1Printer

L.S. 1

C REMOTE PUMPING STATION RBF KARNPRAYAG

Clear water pumping





1

Design, Supply, installation, testing and Commissioning of PLC (Programmable Logic Controller) based RTU & Telemetry system with digital input module, digital output module , analog input module, analog output module communication ports etc. at each Pumping station / Reservoir

L.S. 1

2

Design, Supply, installation, testing and Commissioning of GSM-GPRS Modem bank for Telemetry Communication system with power supply & communication cable etc.

No 2

3

Design, Supply, installation, testing and Commissioning of Actuator Valve with control unit & appropriate bracket / mounting arrangement including two nos. limit switches for open and closed condition and splash proof enclosure along with construction of valve pit etc. complete in all respects

No 2

Design, Supply, installation, testing and Commissioning of full bore type electromagnetic flow meter on pump outlet. The sensor shall be installed in Pipe line including necessary arrangements for the same including excavation, line cutting mounting seat etc.

4

0-100 m3/hr flow range Pipe size : 200mm L.S. 1

5 Supply, installation, testing and Commissioning of Ultrasonic level sensor + transmitter + display for the sumps / reservoirs of range 0-8mtr.

No 2





Supply, installation, testing and Commissioning of Diaphragm type Pressure transmitter with 4-20mA DC (isolated) LCD/LED display, Die cast aluminium housing, IP 65, ±0.5% of span or better accuracy with siphon, manifold and SS316 fitting & tubing with required all accessories for complete the system.

6

Range:0-30 kg/cm² No 2

7

Supply, installation, testing and Commissioning of Die cast aluminium, Bourdon type glycerine filled pressure gauge, 150 mm dial, sensing material SS316, IP 65, 130% over range protection, Shatterproof glass, ± 1% or better accuracy, blow out disc & adjustment screw with siphon tube and isolating manifold with isolation valve & required accessories etc. as per latest Indian Standard & BS EN 837


8 Design, Supply, installation, testing and Commissioning of lightning surge arresters

No 2

RBF Well water pumping

1

Design, Supply, installation, testing and Commissioning of PLC (Programmable Logic Controller) based RTU & Telemetry system with digital input module, digital output module, analog input module, analog output module communication ports etc. at each Pumping station / Reservoir

L.S. 1

2


L.S. 1





3 Supply, installation, testing and Commissioning of Ultrasonic level sensor + transmitter + display for the sumps / reservoirs of range 0-8mtr.

No 1


4


Design, engineering, Procurement, Installation, Testing and Commissioning of instruments for Water Quality measurement Residual Chlorine Analyser measuring system comprising of:

Gas chlorination unit -01

Residual chlorine sensor incl. flow block module with Sensor measuring module for free chlorine with flow regulating valve, Non return valve, Flow tube for sample water from 10mtrs from the chemical dosing point inclusive of all accessories complete in all respects.-----01

Electronic Residual chlorine Analyser module SFC

24 VDC operated wall mounting Feedback control

5

unit and for visualisation of the measured data, prepared for the reception of 1 sensor measuring module, including the following standard features:

L.S.

1





- temperature input PT1000

- actuator feedback signal

- 2 x analog input

- 2 x digital input

- analog output

- 4 x relays output

- interfaces:

* RS485 for connecting a W&T-Chem.

Web-Server, OPC server or CMS software

* RS232 for firmware update

- real time clock

- SD card slot

- enclosure IP66

- ambient temperature 0-50°C/32-122°F

- dimensions: W270 x H147 x D185 mm-----01

SIGNAL TRANSMITTER & POWER SUPPLY

Suitable for 4-20mA input & 0-10/4-20mA output signal 230V operated with 24V DC regulated power supply of 10 Amp., Control MCB’s, relays, wiring set suitable for communication with the PLC SCADA system & Mounting panel including Electronic dosing pump with all accessories according to rating of pump.----01

6 Design, Supply, installation, testing and No 2





Commissioning of lightning surge arresters

7

Design, Supply, installation, testing and Commissioning of Instrumentation cable of 4core*1.5sq.mm in PVC conduit on wall as per requirement

mts

300

8

Supply and fixing of Class B G.I./PVC Pipe with excavation, refilling of sand complete as per requirement for field instrument like flow transmitter & motorised actuator etc

mts

60

Illumination

9

Design, Fabrication, Supply, Erection, Testing and Commissioning of Hot dipped, galvanised steel, octagonal pole conforming to IS: 2713 (part I-III) with latest amendments and with galvanised base plate of size 400mm x 400mm x 7mm in position including excavation of the pit and filling the same with Cement Concrete of M-10 grade (1Cement :3Coarse Sand :6Graded stone aggregate 40 mm nominal size) from base plate to 50cm above ground level, with the help of steel frame not less than 40 cm dia. Duly finished with cement plaster, earthing terminals, cable entry, GI cable sleeve complete as required including excavation and refilling. The pole shall be galvanised and use ISI mark seamless tube for structural purpose. It shall include junction box for terminating 2/3/4 core armoured copper cables up-to 4 sq. mm. Painting of poles with two coats of red oxide. A coat of bituminous paint shall be provided to the portion to





be buried and exposed portion to be applied with two coats of aluminium paints. It shall be as per site requirement and in line with IS 1944 with latest amendments.

9 mtr. L.S. 1

10

Supply, Erection ,Testing and Commissioning of IP -54 protected, integral, medium/low bay, suspended mounting, luminaire suitable for metal halide (MH) lamp comprising of powder coated die cast aluminium housing, electrochemically brightened and anodized aluminium reflector, covered with suitably silicon rubber gasketed heat resistant and toughened clear glass, porcelain holder, integral cast aluminium control gear box having low loss copper ballast, capacitor, electronic ignitor prewired with PVC insulated copper conductor up to corrosion resistant terminal block including making termination etc. as required with lamp. It shall be as per site requirement and in line with IS 3646 with latest amendments.

1 x 150 watt Nos. 1

11

Supply, Erection, Testing and Commissioning of Industrial type fluorescent tube fitting with fluorescent rod and reflector fabricated from Polycarbonate body and finished with powder coating / virous enamelled complete with all accessories like starter, starter seal, low loss copper ballast, condenser, rotor holder, corrosion resistant terminal block duly wired with copper conductor including making termination etc. as required. It





shall be as per site requirement and in line with IS 3646 with latest amendments.

11.1 2 x 36W Nos 2

11.2 1 x 36W Nos 2

12

Supply, Erection, Testing and Commissioning of surface mounting CFL complete with accessories, extra low watt loss copper ballast, starter, holder, condenser, corrosion resistant terminal block duly prewired with copper conductor including making termination as required with lamp. It shall be as per site requirement and in line with IS 3646 with latest amendments.

1 x 18W Nos 2

Wiring

13

Providing and Wiring of light point/fan point with single core, 1.5 sq. mm , fire resistant, PVC insulated , copper conductor ,1.1kV grade and single core ,1 sq.mm , fire resistant , PVC insulated, earth copper conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ,ISI marked, 20mm GI conduit fixed with saddles and spacers and other accessories, for above false ceiling ,or on ceilings ,on beams, including flush metal box with earth terminal, neutral looping in switch board, 6 A piano (flush) switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, bushes, check nuts, making connections, testing etc. as required.(Maximum three switchboard in one circuit-one SP MCB) for the following:





13.1 One 6A modular switch controlling one light/fan point

Nos 4

13.2 6A socket outlet with 6A modular switch (on common board)

Nos 2

13.3 6A socket outlet with 6A modular switch (as an independent point)

Nos 2

14

Providing and Wiring of 6/16 Ampere Switch and socket complete with necessary wiring from DB of 2 no of 4.0 sq. mm. wires and 1 no of 2.5 sq. mm. PVC Insulated copper conductor wire laying in with 25 mm dia. GI conduits of 1.5 mm thick, ISI mark for following. These will be used with point wiring of power points etc.


Nos 2

Earthing

15

Design, Supply and Laying Pipe in Pipe Earthing in conformance with IS:3043 and tested at CPRI with perforated 3.0 Mtr. Long, 25 and 48 mm dia. ' B ' class Zinc coated two mild steel pipe including all accessories such as nut, bolts, reducer, nipple, wire meshed funnel, and making masonry chamber of 450mmx450mmx450mm with mild steel chequered cover and locking arrangement ,embodying the pipe complete with highly conductive and corrosion resistance crystalline mixture plus back fill compound , testing of earth resistance complete as required.

Nos. 10





16

Design, Supply and Laying following size earth strip/risers as a part of earth grid in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. complete as required to be laid 600mm below ground and for earthing transformer neutral, transformer enclosure, Outdoor ABS, indoor 11kV LBS, 415V MCC, Power distribution board etc. complete as required.

60mmx10mm G.I. strip mts 100

17

Design, Supply and Laying following size earth strips/risers in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. conductor to be on floor, trench and wall for earthing outdoor lightning arresters, Lighting Distribution Board etc. complete as required.

25 mm x 3 mm G.I. strip mts 50

Safety equipments

18

Supplying C02 type, portable Fire extinguishers, of size 5kg each , manufactured from CRCA sheets in all welded construction, body coated with glossy corrosion resistant epoxy powder coating ,with inbuilt water proof pressure gauge ,with wall bracket ,as per IS 2190 and IS 13849 with latest amendments.

Nos 1





19

Supplying 11kV, B' class, non-skid, high voltage insulation synthetic mat made from elastomeric polymer material, 1000mm wide, 2.5 mm thick, Dielectric strength 45 kV for 1 minute, fire retardant, no adverse effect of transformer oil, diesel, acid, alkali, High Tensile & Elongation properties, good mechanical strength to withstand load and movement of breaker trolley ,as per IS 15652 with latest amendments

Sqm 3

20

Supplying 415 V, A' class, non-skid, high voltage insulation synthetic mat made from elastomeric polymer material, 1000mm wide, 2.0 mm thick, Dielectric strength 3300V for 1 minute, fire retardant, no adverse effect of transformer oil, diesel, acid, alkali, High Tensile & Elongation properties, good mechanical strength to withstand load and movement of breaker trolley, as per IS 15652 with latest amendments.

Sqm 6

21

Providing A0 size drawing of SLD in wooden frame with glass. The drawing shall be fully dimensioned and must show HV switchgear, transformer, LV switchboards, protection panels, batteries and battery chargers, fire extinguishers, equipment, storage and drawing holders.

Nos 1

22 Supplying Shock treatment chart, duly laminated in Hindi (Local) and English language.

Nos 1

23 Supplying First aid box with all essential medicines including wall mounted bracket

Nos 1





24

Supplying 11000 V, Aluminium, anodised Danger caution plate in Hindi (local) and English languages with the sign of skull and bones in signal red colour on front side, as per IS 2551with latest amendments.

Nos 2

25


Nos 4

26

Supplying Shock proof, Rubber insulated hand gloves, produced through seamless process for minimum working voltage of 11000 V. Should be electricity insulated and tested, should provide dexterity and protection beyond the wrist - length: minimum - 36 cm, white cream colour, soft and flexible quality. With Test Certificate as per IS 4770 with latest amendments.

Pair 1

27

Supplying PVC Safety Helmet with PVC head band, made from HDPE thermoplastic with fully adjustable type head band, sweat band and nylon chin strap. Colour - YELLOW, with logo. As per IS 2925 with latest amendments.

Nos 1

28

Supplying Safety goggles made of impact resistant poly-carbonate, scratch resistant, 100 % poly carbonate lens and 100% UV protection, Scratch resistant - vision, curved lenses provides 180 degree vision, good impact resistance and adjustable temples for comfort and fitness as per EN-166 with latest amendments.

Nos 1





29

Supplying Re-usable type, Ear plug smooth and dirt resistant surface, protection for high noise situation up-to 105 dBA made from non-irritant soft foam base hypo-allergic material - smooth surface. Universal size, tapered shape, smooth surface fits into all Ear canals and gives comfortable consistent and protection. Should provide measured attenuation of minimum 30 dB confirm to ANSI S319 with latest amendments.

Pair 1

30

Supplying Ear muff with wide ahead band with padding shall provide firm and comfortable fit, easily adjustable multi-position [over-head/under chin/behind head] headband with / without elastic crown strap for individual fit. NRR min 24 dB. CE certified /EN 352 approved / ANSI approval S3.19 / as per IS 6229 with latest amendments.

Pair 1

31

Supplying Galvanised mild steel sand Fire bucket with lid and handle, 9 Litres capacity. Buckets to be provided with suitable strand with 4 Nos. hooks to hang sand filled buckets, as per IS 2546 with latest amendments.

Set 1

32

Design, Supply, Installation, Testing and Commissioning of 400 kW/500kVA,3 Phase, 4 wire, 415V+/- 1%,50 Hz Diesel Generator set conforming to the latest IS:4722,BS 649 comprising radiator cooled engine coupled with Alternator efficiency not less than 93.5%, insulation class F, 10 % overload for 1 hour in every 12 hours, conforming to the latest IEC:60034, complete with standard accessories such as acoustic enclosure mounted on channel

L.S. 1





iron base frame, 360AH battery with leads and terminals, 700 litres fuel tank, manual control panel including MCCB conforming to the latest IS/IEC :60947, outgoing cable, initial battery charging, first fill of diesel, change over switch, kWH meter, Statutory approval, PCC foundation etc.


Name of Bidder

Signature of Bidder



Schedule No. B3– Environmental Management & Monitoring (Karnaprayag)





Lump sum 1



Per Sample 5





Lump sum 1




23



18







23



54


Per Sample 15


Per Year 15


Per Sample 12


Name of Bidder

Signature of Bidder



Schedule No. C (Gauchar) Schedule No. C1 - Rehabilitation and Augmentation of Water Supply Scheme in Gauchar Town


Description Unit Quantity In Figures

In Words Amount

(INR)

1 Infiltration Well and Pump House

Soil investigation, conducting SBC and infiltration rate test, Design, supply, Construction, testing, commissioning of infiltration well of 2.53 MLD and construction of Pump House above infiltration well at Alaknanda River site, clearing, grading, including but not limiting the specification mentioned in Section -6- Employers Requirements of the Bid Documents including fixing crane for lifting pumps including supply of all materials, labour, tools, plants and other equipments or any other item required for the proper completion of work in all respect as per specification as directed by the Engineer with approach bridge, all lead, lift, diversion of flow and dewatering of water etc. complete (On Lump sum Basis)

No. 1

2

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of Sump of capacity 100KL or more as per specification and directions of engineer-in-charge.

L.S. 1

3

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of pump house of atleast 20 Sq.m. area or more for HSCF pumps as per the requirement of pump installation including fixing crane for lifting pumps as per specification and directions of engineer-in-charge.

Sq.m 20





In Words Amount

(INR)

4

Supplying, erecting, testing and commissioning of Submersible type Pumpset of capacity 1757 LPM (minimum) with pumping head of 20 meters and lowering upto a depth of 20 meter minimum including all required piping upto floor level of Pump house for Infiltration Well including all materials, specials, labour, machineries for erection, lowering of pumpsets with all transportation etc., as per specification and as directed by the Engineer.

No. 2

5

Supplying, erecting, testing and commissioning of Horizontal Centrifugal type Pumpsets of capacity 1757 LPM (minimum) with pumping head of 160 meters including all required piping from Sump to Pump house and within Pump house including all materials, specials, labour, machineries for erection, lowering of pumpsets with all transportation etc., as per specification and as directed by the Engineer.

No. 2

6 Pipeline Work

6.1

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lifts upto 1.5m, including getting out the excavated soil as directed by Engineer with all lead and lift including danger lighting and using sight rails and boring rods at every 100 m wherever necessary including the cost of labour, tools and plants and any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge.

6.1.1 All Kinds of Soil Cum 1652





In Words Amount

(INR)

6.2


cum 1558

6.3 Supply of MS-ERW pipe (FE-410 grade) conforming to IS 3589:2001 and as per specification.

6.3.1 200mm internal dia 6mm thk -Rising Main Rmt 3000

6.3.2 100mm internal dia 6mm thk - Distribution Main Rmt 1000

6.4

Laying & jointing of Mild Steel pipes (FE-410 grade) conforming to IS 3589:2001 and Mild steel specials (bends, tees, tapers etc) confirming to IS 7322 including perfect linking and welding of joints to correct position including cost and conveyance of pipes and materials with all lead and lifts, cost of labour and giving satisfactory hydraulic test as per IS 3589:2001 with water supplied at the cost of the contractor for test pressure and working pressure both at factory and site etc. and including the cost of ultrasonic / radiographic test as per relevant IS, complete as per detailed specification with liquid epoxy coating for internal & external surface of the pipeline as per clause 16.1 of ANNEX B as per IS 3589:2001 (latest revision) including loading and unloading of pipes for the following clear internal diameter before coating and specified thickness of plate as mentioned below, complete as per detailed specifications and as directed by the Engineer.





In Words Amount

(INR)

6.4.1 200mm internal dia 6mm thk - Rising Main Rmt 3000

6.4.2 100mm internal dia 6mm thk - Distribution Main Rmt 1000

6.5


6.5.1 40 mm GI pipe for Distribution pipeline (Medium duty Class) Rmt 950




6.6



6.6.2 100mm dia PN 1.6 Sluice Valve for 100mm Pipe No. 2





In Words Amount

(INR)

6.7

Supplying, delivering and fixing DI Scour valve conforming to IS 14846 with latest amendments with all lead and lift complete as per specifications and fixing and jointing of DI Sluice valves true to line and gradient, including cost of DI / MS specials (tail pieces, Tees, dismantling joints, puddle flanges, flanges, duck foot bend, bend, semicircular bend), for the specified diameters including cost of jointing materials like bolts, nuts, rubber insertions, labour, testing etc., complete as per drawing and as per detailed specifications and as directed by the Engineer Incharge.


6.7.2 100 mm dia PN 1.6 Sluice Valve for 100mm Pipe No. 2

6.8

Supply, Laying and Jointing of brand new DI kinetic Double Orifice Air valve approved by the Engineer having small elastic ball resting on gun metal orifice nipple and large orifice vulcanite ball seating ring with built-in kinetic features and rating of PN 1.0 with isolating DI sluice valve of PN 1.0 rating having body, door, dome, gland, non rising stainless spindle, Flanges drilled to IS:1538, valves tested by closed method, mounted in a horizontal position, and operated by metre wheel gearing of approved quality with bolts, nuts, rubber insertions etc. complete as per drawing and as directed by the Engineer.

6.8.1 80 mm dia Air Valve No. 2

6.9

Supply and fixing of brand new Bulk Water Meter (Woltmann type cold water meter) 200mm dia of approved make having facility to incorporate RF based wireless remote transreceivers for automatic meter reading. The water meters shall be with removable mechanism, magnetic

No. 1





In Words Amount

(INR)

drive, dry dial, hermetically sealed register, class B type, manufactured in accordance with ISO-4064 standards or equivalent. The meter body shall be flanged end for connection and the bolt hole drilling shall be as per IS 1538. The meter body shall be cast iron as per IS 210 Gr FG260 and shall be coated with a high quality fusion bonded powder coating inside and outside the meter body. The meters shall be equipped with a suitable strainer for longer life of the meter. The meters performance specifications shall be EEC/ISO-4064 Class-B performance. Accuracy shall be in accordance with ISO & EEC class B. The meter shall be suitable to work at working pressure of 16 Bar & temperature of 45oC. The meter shall be preequipped for SCADA and suitable communication including CI Sluice valve IVC/ IVI / KBL / R & D/ Kejriwal make as per IS 14846 with latest amendments for Control and cost of specials (puddle flanges, flanged tail piece, Dismantling joint and flanges & necessary reducer and enlargers to fix the Bulk Meters) and jointing materials complete with all lead and lift and as per detailed specifications and as directed by the Engineer Incharge.

6.10

Providing RCC Chambers of required specifications as per drawings and as directed by the Engineer Incharge for Sluice valves, Air valves and Scour valves, Source rehabilitation etc.

No. 15

7 Site Protection Works





In Words Amount

(INR)

7.1

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc up to floor five level, excluding the cost of centering , shuttering and finishing:

7.1.1 1:2:4 (1 Cement : 2 Coarse sand : 4 graded stone aggregate 40 mm nominal size)

Cum 77

7.1.2 1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Cum 698

7.2 Providing Centering and Shuttering works for RCC work at different locations

Sq.m. 840

7.3

Providing, supplying and fabricating of reinforcement using TMT bars of all sizes including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position, tieing with binding wire of approved quality and gauge including the cost of binding wire and anchoring to adjoining members wherever necessary including all laps and wastages etc., with all lead and lifts, complete as per design, specification and as directed by the Engineer at different locations

Kg 60818

8

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of Clear water Reservoir as per required design using RCC construction with all necessary arrangements, water level indicator etc all complete as per drawing and as directed by the Engineer.

8.1 100KL Near Police Chowki Job 1





In Words Amount

(INR)

9

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of RCC Framed structure (Normal Building) floor height 3.35 mtr. for Office Building as per specification for area atleast 200sqm for Office building (G Floor Only)

Sq. m. 200

10

Soil investigation, conducting SBC and Design, supply, Construction, testing, commissioning RCC framed structure for Transformer Room as per specification for area of 24sqm.

Sq. m. 24

11


Cum 100


Name of Bidder

Signature of Bidder



Schedule No. C2 - Electrical and Automation works (Gauchar)

Unit Rate (INR) S. N. DESCRIPTION Unit Quantity

In Figures In Words Amount

(INR)

Medium Voltage Primary Supply

1

Design, Supply, Receiving, Storing, Inspection, Handling, Assembling, Installing in correct aligned position, 11 kV, 22.6 kA/1SEC, 100A outdoor type, approved make, Air break switch (ABS) with Earth switch, power contact position indicator, padlocking facility, auxiliary contacts and all other accessories for satisfactory operation as per detail specification, in conformance with IS:9921, as required by the statutory electrical authorities guidelines and as per reference 11kV Single Line Dwg. GW/01/GC-E-001

L.S. 1

2

Design, Supply, Receiving, Storing, Inspection, Handling, Assembling, Installing in correct aligned position, effecting proper Connections, Testing and Commissioning of 11kV/0.433 kV, 3 Phase, 50Hz, 400 kVA, ONAN cooled, mineral Oil filled, Dyn11, copper wound, approved make, transformer having + 5 % to -15 % On Load Tap Changer, cable box on 11kV side suitable for 1 Run of 3C x 240 sq. mm. Aluminium conductor armoured cable and cable box on secondary side suitable for 2R x 3.5C x 240 sq. mm. XLPE, Aluminium conductor armoured cables. Transformer shall be

L.S. 1





(INR)

provided with all the accessories and fittings conforming to IS 2026(Part I-IV), ECBC, IS 6600 with its latest amendments and as per approved data sheet.

3

Design, Supply, Termination and Commissioning of Raychem HV Indoor type heat shrinkable termination kit of approved make complete with all accessories suitable for 3 core 50 sq. mm., 11 kV, XLPE insulated, FRLS sheathed, aluminium conductor armoured cable. It shall withstand the range of ambient temperature experienced in Gauchar.

No 2

LV Power distribution and Motor Control Centre

1

Design, Supply, Installation, Testing and commissioning of LT Power distribution board for Mains supplies distribution as per specifications

No 1

2

Design, Supply, Installation, Testing and commissioning of Lighting Distribution Boards for Indoor and Outdoor lighting and auxiliaries.

No. 2

3

Design, Supply, Installation, Testing and commissioning of SCADA compatible Motor control centre as per specifications given at for RBF I- WELL water pumping suitable for 2*7.5KW pumps

No 1





(INR)

4

Design, Supply, Installation, Testing and commissioning of SCADA compatible Motor control centre as per specifications given at for Clear water pumping suitable for 2*120HP pumps

No 1

5

Design, Supply and laying of Power cables with Tray/clamped to wall with suitable clamps, saddles and fixing bolts/ in ground including the cost of digging and backfilling with sand and brick protection as required and including testing and commissioning of the following sizes of 1.1kV grade multi core aluminium conductor XLPE insulated and FRLS sheathed armoured cable conforming to IS: 7098 (Part-I) with latest amendments. The costs shall include properly clamping with cable clamps, terminal lugs and ties. Identification tags shall be provided for all cables.

L.S. 1







4C X 10 sq.mm. As per site

Automation, SCADA and instrumentation





(INR)

A MASTER CONTROL STATION AT DEHRADUN

(a)

Design, Supply, installation, testing and Commissioning of water management SCADA software including screen development, report development with SQL server base & necessary associated software as detailed in specifications sheet.

L.S. 1

(b)

Design, Supply, Installation, Testing and commissioning of GSM-GPRS Modem bank for Telemetry Communication system with power supply & communication cable etc.

L.S. 1

(c) Design, Supply and Installation of 1 PC, 1 UPS, 1Printer

L.S. 1

B Local Control Station at Gauchar

(a)

Design, Supply, installation, testing and Commissioning of water management SCADA software including screen development, report development with SQL server base & necessary associated software as detailed in specifications

L.S. 1

(b)

Design, Supply, Installation, Testing and commissioning of Modem bank for Telemetry Communication system with power supply & communication cable etc.

L.S. 1

(c) Design, Supply and Installation of 1PC, 1KVA UPS, 1Printer

L.S. 1

C Remote Pumping Station RBF Gauchar

Clear water pumping





(INR)

1

Design, Supply, installation, testing and Commissioning of PLC (Programmable Logic Controller) based RTU & Telemetry system with digital input module, digital output module , analog input module, analog output module communication ports etc. at each Pumping station / Reservoir

L.S. 1

2


No 2

3

Design, Supply, installation, testing and Commissioning of Actuator Valve with control unit & appropriate bracket / mounting arrangement including two nos. limit switches for open and closed condition and splash proof enclosure along with construction of valve pit etc. complete in all respects

No 2

Design, Supply, installation, testing and Commissioning of full bore type electromagnetic flow meter on pump outlet. The sensor shall be installed in Pipe line including necessary arrangements for the same including excavation, line cutting mounting seat etc.

4

0-150 m3/hr flow range Pipe size : 200mm No 1

5 Supply, installation, testing and Commissioning of Ultrasonic level sensor + transmitter + display for the sumps /

No 2





(INR)

reservoirs of range 0-8mtr.

Supply, installation, testing and Commissioning of Diaphragm type Pressure transmitter with 4-20mA DC (isolated) LCD/LED display, Die cast aluminium housing, IP 65, ±0.5% of span or better accuracy with siphon, manifold and SS316 fitting & tubing with required all accessories for complete the system.

6



7



No 2

RBF Well water pumping

1

Design, Supply, installation, testing and Commissioning of PLC (Programmable Logic Controller) based RTU & Telemetry system with digital input module, digital output module , analog input module, analog output module communication ports etc. at

L.S. 1





(INR)

each Pumping station / Reservoir

2


L.S. 1

3

Supply, installation, testing and Commissioning of Ultrasonic level sensor + transmitter + display for the sumps / reservoirs of range 0-8mtr.

No 1


4


5

Design, engineering, Procurement, Installation, Testing and Commissioning of instruments for Water Quality measurement Residual Chlorine Analyser measuring system comprising of: Gas chlorination unit -01 Residual chlorine sensor incl. flow block module with Sensor measuring module for free chlorine with flow regulating valve, Non return valve, Flow tube for sample water

L.S.

1





(INR)

from 10mtrs from the chemical dosing point inclusive of all accessories complete in all respects.-----01 Electronic Residual chlorine Analyser module SFC 24 VDC operated wall mounting Feedback control unit and for visualisation of the measured data, prepared for the reception of 1 sensor measuring module, including the following standard features:

- temperature input PT1000

- actuator feedback signal

- 2 x analog input

- 2 x digital input

- analog output

- 4 x relays output

- interfaces:

* RS485 for connecting a W&T-Chem.

Web-Server, OPC server or CMS software

* RS232 for firmware update

- real time clock

- SD card slot

- enclosure IP66

- ambient temperature 0-50°C/32-122°F

- dimensions: W270 x H147 x D185 mm-----01





(INR)

SIGNAL TRANSMITTER & POWER SUPPLY Suitable for 4-20mA input & 0-10/4-20mA output signal

230V operated with 24V DC regulated power supply of 10 Amp., Control MCB’s, relays, wiring set suitable for communication with the PLC SCADA system & Mounting panel including Electronic dosing pump with all accessories according to rating of pump.----01


No 2

7

Design, Supply, installation, testing and Commissioning of Instrumentation cable of 4core*1.5sq.mm in PVC conduit on wall as per requirement

mtrs

300

8

Supply and fixing of Class B G.I./PVC Pipe with excavation, refilling of sand complete as per requirement for field instrument like flow transmitter & motorised actuator etc

mtrs 60

Illumination

9

Design, Fabrication, Supply, Erection, Testing and Commissioning of Hot dipped, galvanised steel, octagonal pole conforming to IS: 2713 (part I-III) with latest amendments and with galvanised base plate of size 400mm x 400mm x 7mm in position including excavation of the pit and filling the same with Cement Concrete of M-10 grade





(INR)

(1Cement :3Coarse Sand :6Graded stone aggregate 40 mm nominal size) from base plate to 50cm above ground level, with the help of steel frame not less than 40 cm dia. Duly finished with cement plaster, earthing terminals, cable entry, GI cable sleeve complete as required including excavation and refilling. The pole shall be galvanised and use ISI mark seamless tube for structural purpose. It shall include junction box for terminating 2/3/4 core armoured copper cables up-to 4 sq. mm. Painting of poles with two coats of red oxide. A coat of bituminous paint shall be provided to the portion to be buried and exposed portion to be applied with two coats of aluminium paints. It shall be as per site requirement and in line with IS 1944 with latest amendments.

9 mtr. L.S. 1

10

Supply, Erection, Testing and Commissioning of IP -54 protected, integral, medium/low bay, suspended mounting, luminaire suitable for metal halide (MH) lamp comprising of powder coated die cast aluminium housing, electrochemically brightened and anodized aluminium reflector, covered with suitably silicon rubber gasketed heat resistant and toughened clear glass, porcelain holder, integral cast





(INR)

aluminium control gear box having low loss copper ballast, capacitor, electronic ignitor prewired with PVC insulated copper conductor up to corrosion resistant terminal block including making termination etc. as required with lamp. It shall be as per site requirement and in line with IS 3646 with latest amendments.

1 x 150 watt Nos. 1

11

Supply, Erection, Testing and Commissioning of Industrial type fluorescent tube fitting with fluorescent rod and reflector fabricated from Polycarbonate body and finished with powder coating / virous enamelled complete with all accessories like starter, starter seal, low loss copper ballast, condenser, rotor holder, corrosion resistant terminal block duly wired with copper conductor including making termination etc. as required. It shall be as per site requirement and in line with IS 3646 with latest amendments.

11.1 2 x 36W Nos 2

11.2 1 x 36W Nos 2

12

Supply, Erection, Testing and Commissioning of surface mounting CFL complete with accessories, extra low watt loss copper ballast, starter, holder, condenser, corrosion resistant terminal block duly prewired with copper conductor





(INR)

including making termination as required with lamp. It shall be as per site requirement and in line with IS 3646 with latest amendments.

1 x 18W Nos 2

Wiring

13

Providing and Wiring of light point/fan point with single core, 1.5 sq. mm , fire resistant, PVC insulated , copper conductor ,1.1kV grade and single core ,1 sq.mm , fire resistant , PVC insulated, earth copper conductor 1.1 kV grade (IS:694) of approved make in surface / recessed ,ISI marked, 20mm GI conduit fixed with saddles and spacers and other accessories, for above false ceiling ,or on ceilings ,on beams, including flush metal box with earth terminal, neutral looping in switch board, 6 A piano (flush) switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, bushes ,check nuts, making connections, testing etc. as required.(Maximum three switchboard in one circuit-one SP MCB) for the following:

13.1 One 6A modular switch controlling one light/fan point

Nos 4

13.2 6A socket outlet with 6A modular switch (on common board)

Nos 2





(INR)


Nos 2

14

Providing and Wiring of 6/16 Ampere Switch and socket complete with necessary wiring from DB of 2 no of 4.0 sq. mm. wires and 1 no of 2.5 sq. mm. PVC Insulated copper conductor wire laying in with 25 mm dia. GI conduits of 1.5 mm thick, ISI mark following. These will be used with point wiring of power points etc.


Nos 2

Earthing

15

Design, Supply and Laying Pipe in Pipe Earthing in conformance with IS:3043 and tested at CPRI with perforated 3.0 Mtr. Long, 25 and 48 mm dia. ' B ' class Zinc coated two mild steel pipe including all accessories such as nut, bolts, reducer, nipple, wire meshed funnel, and making masonry chamber of 450mmx450mmx450mm with mild steel chequered cover and locking arrangement ,embodying the pipe complete with highly conductive and corrosion resistance crystalline mixture plus back fill compound , testing of earth resistance complete as required.

Nos 10





(INR)

16

Supply and laying following size earth strip/risers as a part of earth grid in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. complete as required to be laid 600mm below ground and for earthing transformer neutral, transformer enclosure, Outdoor ABS, indoor 11kV LBS, 415V MCC, Power distribution board etc.

60mmx10mm G.I. strip Mts 100

17

Supply and laying following size earth strips/risers in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. conductor to be on floor, trench and wall for earthing outdoor lightning arresters, Lighting Distribution Board etc.

25 mm x 3 mm G.I. strip Mts 50

Safety equipments

18

Supplying C02 type, portable Fire extinguishers, of size 5kg each, manufactured from CRCA sheets in all welded construction, body coated with glossy corrosion resistant epoxy powder coating, with inbuilt water proof pressure gauge, with wall bracket, as per IS 2190 and IS 13849 with latest amendments.

Nos 1





(INR)

19

Supplying 11kV, B' class, non-skid, high voltage insulation synthetic mat made from elastomeric polymer material, 1000mm wide, 2.5 mm thick, Dielectric strength 45 kV for 1 minute, fire retardant, no adverse effect of transformer oil, diesel, acid, alkali, High Tensile & Elongation properties, good mechanical strength to withstand load and movement of breaker trolley ,as per IS 15652 with latest amendments

Sqm 3

20

Supplying 415 V, A' class, non-skid, high voltage insulation synthetic mat made from elastomeric polymer material, 1000mm wide, 2.0 mm thick, Dielectric strength 3300V for 1 minute, fire retardant, no adverse effect of transformer oil, diesel, acid, alkali, High Tensile & Elongation properties, good mechanical strength to withstand load and movement of breaker trolley, as per IS 15652 with latest amendments.

Sqm 6

21

Providing A0 size drawing of SLD in wooden frame with glass. The drawing shall be fully dimensioned and must show HV switchgear, transformer, LV switchboards, protection panels, batteries and battery chargers, fire extinguishers, equipment, storage and drawing holders.

No 1

22 Supplying Shock treatment chart, duly laminated in Hindi (Local) and English

Nos 1





(INR)

language.

23 Supplying First aid box with all essential medicines including wall mounted bracket

Nos 1

24

Supplying 11000 V, Aluminium, anodised Danger caution plate in Hindi (local) and English languages with the sign of skull and bones in signal red colour on front side, as per IS 2551 with latest amendments.

Nos 2

25


Nos 4

26

Supplying Shock proof, Rubber insulated hand gloves, produced through seamless process for minimum working voltage of 11000 V. Should be electricity insulated and tested, should provide dexterity and protection beyond the wrist - length: minimum - 36 cm, white cream colour, soft and flexible quality. With Test Certificate as per IS 4770 with latest amendments.

Pair 1

27

Supplying PVC Safety Helmet with PVC head band, made from HDPE thermoplastic with fully adjustable type head band, sweat band and nylon chin strap. Colour - YELLOW, with logo. As per IS 2925 with latest amendments.

Nos 1





(INR)

28

Supplying Safety goggles made of impact resistant poly-carbonate, scratch resistant, 100 % poly carbonate lens and 100% UV protection, Scratch resistant - vision, curved lenses provides 180 degree vision, good impact resistance and adjustable temples for comfort and fitness as per EN-166 with latest amendments.

Nos 1

29

Supplying Re-usable type, Ear plug smooth and dirt resistant surface, protection for high noise situation up-to 105 dBA made from non-irritant soft foam base hypo-allergic material - smooth surface. Universal size, tapered shape, smooth surface fits into all Ear canals and gives comfortable consistent and protection. Should provide measured attenuation of minimum 30 dB confirm to ANSI S319 with latest amendments.

Pair 1

30

Supplying Ear muff with wide ahead band with padding shall provide firm and comfortable fit, easily adjustable multi-position [over-head/under chin/behind head] headband with / without elastic crown strap for individual fit. NRR min 24 dB. CE certified /EN 352 approved / ANSI approval S3.19 / as per IS 6229 with latest amendments.

Pair 1

31 Supplying Galvanised mild steel sand Fire bucket with lid and handle, 9 Litres capacity. Buckets to be provided with suitable strand

Set 1





(INR)

with 4 Nos. hooks to hang sand filled buckets, as per IS 2546 with latest amendments.

32

Design, Supply, Installation, Testing and Commissioning of 400 kW/200kVA,3 Phase, 4 wire, 415V+/- 1%,50 Hz Diesel Generator set conforming to the latest IS:4722,BS 649 comprising radiator cooled engine coupled with Alternator efficiency not less than 93.5%, insulation class F, 10 % overload for 1 hour in every 12 hours, conforming to the latest IEC:60034, complete with standard accessories such as acoustic enclosure mounted on channel iron base frame, 360AH battery with leads and terminals, 700 litres fuel tank, manual control panel including MCCB conforming to the latest IS/IEC :60947, outgoing cable, initial battery charging, first fill of diesel, change over switch, kWH meter, Statutory approval, PCC foundation etc.

L.S. 1


Name of Bidder

Signature of Bidder



Schedule No. C3 – Environmental Management & Monitoring (Gauchar)





Lump sum 1



Per Sample 5





Lump sum 1




23



18







23



54


Per Sample 15


Per Year 15


Per Sample 12


Name of Bidder

Signature of Bidder



Schedule No. D (Uttarkashi) Schedule No. D1 – Rehabilitation and Augmentation of Water Supply Scheme in Uttarkashi Town

Unit Rate (INR) Item No Description Unit Quantity


(INR)

Construction of Tube Well Transportation of suitable truck mounted Rig machine, air compressor, OP unit, camp equipage, connected T&P and necessary accessories, casing pipe, tubewell assembly housing pipe etc. including loading, unloading erection and levelling of rig machine upto site of work etc. complete in all respect as per direction of Engineer incharge, required for drilling 400mm dia tubewell for a depth of minimum 45 meters. Drilling of bore of 400mm dia by rig machine using Percussion method in alluvial, boulders, pebbles, rocky stone, sticky clay etc. from ground level upto entire depth (minimum 45 meters from GL) ordered by the department.

1

Supplying, Transporting, Sinking/Lowering of 400mm dia of MS ERW casing pipe in drilled and lined bore as below from ground level upto entire depth (minimum 20 meters from GL) ordered by the department.

LS

2





(INR)

Lowering of tubewell assembly pipe of 200mm dia 6.4 mm thick MS ERW Housing plain ended blind pipe/slotted pipe, starting from ground level to the required depth (minimum 45 meters from GL) ordered by the department including cutting, welding as required at site complete with all T&P required.

Supply and making of required size sleeve joints lowering and fixing.

The MS ERW Casing Pipe conforming to IS: 4270/2001 shall be 400mm dia of 8 mm wall thickness mentioned as per specification. The outer surface of casing pipe shall be painted with anti corrosive paint. Assembly shall be lowered, keep the bore vertical. The free end of the casing pipe shall be minimum 1.0 mtr. above the ground level. Works shall confirm to IS: (i) I.S. 2800 (Part-I):1991 code of practice for construction & testing of tube wells/Bore wells. (ii) I.S. 2800 (Part-II):1979 code of practice for construction & testing of tube wells/Bore wells (Reaffirmed 1999). (iii) I.S. 4097-1998: Gravel for use as pack in tube wells (Reaffirmed 1993. (iv) I.S. 4270:2001 Steel tubes used for water wells.

Tube wells drilled should be perfectly vertical. The rates for drilling are inclusive of the verticality test required to be conducted.





(INR)

The work shall be carried out by the contractor strictly in accordance with the contract specifications and ISI specifications as per IS-2800 (Part-I) 1991, IS-2800 (Part-II) 1979.

All welding work shall be done as per I.S. specification and electrodes used shall be I.S.I. marked

All the gravel to be used as packed in a gravel packed tube wells shall be specified in IS 4097:1988 (reaffirmed 1993). The discharge from tube well during its development shall also be measured by ‘V’ notch for approximation of yield.

Shrouding of pea gravels in between bore and tubewell assembly upto entire depth of tubewell ordered by the department including cost of pea gravels. Including providing and fixing well cap made from MS ERW Pipe and MS Sheet of 8 mm thick, bail plug with nut and bolts as required, casing shoe suitable for ODEX drilling and made from EN-24 steel, MS housing clamp 8 mm thick including nut, bolt and washers complete set & pea gravels of size 1.6 mm to 4.8 mm.

Including dismantling of rig machine and other equipments and clearance of site after finishing the job and as directed by the Engineer.





(INR)

2

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of pump house of atleast 20sqm area or more and suitable height as per the requirement of pump and panel installation including support for fixing crane for lifting pumps as per specification, drawing and directions of engineer-in-charge.

Job 2

3

Supply, erection, testing and commissioning of submersible pumpset of 2000LPM discharge and head of 149 m duty point and Supplying, Transporting, fixing delivery pipe from bottom of tube well and upto pump house floor 35 m (minimum) length with all fittings and clamping arrangement including lifting arrangement of ISMB girder 5 M length and chain pulley block etc including required electrical cables upto Pump House floor level etc. complete.

Nos 2

Earthwork

4

Earthwork in excavation in all kinds of soil by mechanical means (Hydraulic excavator) / manual means of required width for pipes, cables, foundation of thrust blocks, drains or any other similar work including dressing of sides and ramming of bottoms in all depths

4.1 Upto 1.5m depth Cum 3930






(INR)

5


5.1 100 mm dia GI Pipe for Distribution Main (Medium duty Class)

Rmt 3200

6

Supplying, laying & jointing of Mild Steel pipes (Fe-410 grade) of required size and thickness conforming to IS 3589 including perfect linking and welding of joints to correct position. The field jointing/welding is to be carried out by Manual metal arc process as per IS 816. The electrodes to be used shall be of carbon manganese electrode as per IS 814 duly approved by Engineer-in-charge including cost and conveyance of pipes and materials with all lead and lifts, cost of all labour and giving satisfactory hydraulic test as per IS 3589 for test pressure and working pressure both at factory and site etc., complete as per detailed specification with inside & out side epoxy coating as per IS 11906 specification including loading and unloading of pipes etc with all leads & lifts, cost of all materials, labours and sand blasting, etc., complete as per approved drawing, tender specification and as directed by the Engineer in charge





(INR)

6.1 125mm dia (ID) of 5 mm thick Rmt 800

6.2 200mm dia (ID) of 5 mm thick Rmt 1580

6.3 250mm dia (ID) of 6.4 mm thick Rmt 800

6.4 300mm dia (ID) of 6.4 mm thick Rmt 1300

7


7.1 100 mm dia PN 1.0 Sluice valve for 100 mm Pipe No 3




8

Supplying, Laying and Jointing DI Scour valve 200mm conforming to IS 14846 with latest amendments with all lead and lift complete as per specifications and fixing and jointing of DI Sluice valves true to line and gradient, including cost of DI / MS specials (tail pieces, Tees, dismantling joints, puddle flanges, flanges, duck foot bend, bend, semicircular bend), for the specified diameters including cost of jointing materials like bolts, nuts,





(INR)

rubber insertions, labour, testing etc., complete as per drawing and as per detailed specifications and as directed by the Engineer Incharge.

8.1 200mm dia (PN 1.6) for 300mm dia pipe main No 1

9

Supply, Laying and Jointing of brand new DI kinetic Double Orifice Air valve approved by the Engineer having small elastic ball resting on gun metal orifice nipple and large orifice vulcanite ball seating ring with built-in kinetic features with isolating DI sluice valve having body, door, dome, gland, non rising stainless spindle, Flanges drilled to IS:1538, valves tested by closed method, mounted in a horizontal position, and operated by metre wheel gearing of approved quality with bolts, nuts, rubber insertions, labour etc. complete. as per drawing and as directed by the Engineer.

9.1 80 mm dia Air Valve of PN 1.6 No 2

10

Supply, Laying and Jointing of DI Non-Return Valve, including supply of all materials including nuts, bolts, washers & rubber insertion sheets, and provision of suitable support and labour complete with all lead and lift as per specification, approved drawing & as directed by the Engineer.

10.1 200mm dia PN 1.6 No 2

11

Supply and fixing of brand new Bulk Water Meter (Woltmann type cold water meter) of approved make having facility to incorporate RF based wireless remote transreceivers for automatic meter reading. The water meters shall be with removable





(INR)

mechanism, magnetic drive, dry dial, hermetically sealed register, class B type, manufactured in accordance with ISO-4064 standards or equivalent and approved by the Engineer. The meter body shall be flanged end for connection and the bolt hole drilling shall be as per IS 1538. The meter body shall be cast iron as per IS 210 Gr FG260 and shall be coated with a high quality fusion bonded powder coating inside and outside the meter body. The meters shall be equipped with a suitable strainer for longer life of the meter. The meters performance specifications shall be EEC/ISO-4064 Class-B performance. Accuracy shall be in accordance with ISO & EEC class B. The meter shall be suitable to work at working pressure of 16 Bar & temperature of 45 deg C. The meter shall be preequipped for SCADA and suitable communication including CI Sluice valve IVC/ IVI / KBL / R & D/ Kejriwal make as per IS 14846 with latest amendments for Control and cost of specials (puddle flanges, flanged tail piece, Dismantling joint and flanges & necessary reducer and enlargers to fix the Bulk Meters) and jointing materials complete with all lead and lift and as per detailed specifications and as directed by the Engineer Incharge.

11.1 200 mm dia PN 1.6 No 2





(INR)

12

Supplying, laying and jointing of MS specials (Fe-410 grade) of required thickness including tapers, bends, tees, flanges conforming to IS 7322:1985 with latest amendments, perfect linking and welding of joints to correct position. The field welding/ jointing is to be carried out by Manual metal arc process as per IS 816. The electrodes to be used shall be of carbon manganese electrode as per IS 814 duly approved by Engineer-in-charge including cost and conveyance of materials with all lead & lift, cost of labour and giving satisfactory hydraulic test as per IS 3589 for test pressure and working pressure both at factory and at site, complete as per detailed specifications with inside and outside epoxy coating as per IS 11906 specification including loading and unloading of specials etc with all leads & lifts complete including loading & unloading of specials etc. complete as per the approved drawing, tender specifications and as directed by the Engineer in charge.

MT 3.65

13

Providing and fixing House Service Connections (20mm dia) of GI material including providing and fixing DI clamp saddle, brass ferule, collar, Bends, Tees, Brass ball valve, Brass non return valve and required unions to link with existing connection including cost of GI pipe upto property with all labour, materials etc. complete work as per specifications and drawing complete in all respect and as directed by the Engineer.

No 200

Intake Sources, Transmission, Distribution





(INR)

Works

14

Providing and laying PCC of M15 (1:2:4) grade using 20 mm and down size aggregate laid in 15cm thick layers and well compacted, vibrating, curing, finishing with necessary cement mortar (1:4), excluding formwork and centering, and including all lead and lift and cost of labours, tools, tackles and curing as per specifications and as directed by the Engineer. (For Retaining wall, cross wall, Pipe supports, anchor/thrust blocks, valve chambers etc.)

Cum 886

15

Providing and laying Reinforced cement concrete of M20 grade using 20 mm and downsize ISI gauge aggregate including cost and conveyance of all materials excluding formwork, and including machine mixing, laying, tamping, curing etc., complete including smooth finishing the exposed faces neatly with CM (1:4) proportion wherever necessary etc., complete as per specification with all lead and lift and labours, tools, tackles as directed by the Engineer (Exclusive of cost of steel and fabrication charges) (For Retaining wall, cross wall, Pipe supports, anchor/thrust blocks, valve chambers etc.)

cum 87

16

Providing Centering and shuttering including strutting, propping etc. and removal of formwork for reinforced concrete works and including cost of labours, tools, tackles as per specification and as directed by the Engineer.

sqm 800





(INR)

17

Providing, supplying and fabricating of reinforcement of all sizes including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position, tying with binding wire of approved quality and gauge including the cost of binding wire and anchoring to adjoining members wherever necessary including all laps and wastages etc., with all lead and lifts and cost of labours, tools, tackles complete as per design, specification and as directed by the Engineer.

MT 13

18

Providing and laying Random rubble masonry with hard stone including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) with Cement mortar 1:6 (1 cement : 6 coarse sand) including labour, all lead & lift, as per specification, as per drawing and as directed by the Engineer. (For retaining wall at Gufiyara WTP).

18.1 With available rubble hard stones Cum 50

18.2 With new rubble hard stones Cum 50

19 Providing and laying 4 kg/cm2 PVC Pipe of 75mm dia for weep hole including all labour, all lead & lift, etc. complete

Rmt 225

20 Providing and laying filter media of aggregate size 20mm for weep hole etc. complete

Cum 10

21

Backfilling with available excavated earth (excluding rock) in pipe trenches, plinth side, foundation of valves or any other structure in layers not exceeding 20 cm in depth, consolidating each deposited layers by ramming and watering with all lead and lift and

Cum 3500





(INR)

depth upto 1.5 m including the cost of labours, tools and plants, water or any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge.


Name of Bidder

Signature of Bidder



Schedule No. D2 - Rehabilitation of Uttarkashi WTP's

Unit Rate (INR) Sr. No.


Amount (INR)

1

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lifts upto 1.5m, including getting out the excavated soil as directed by Engineer with all lead and lift including danger lighting and using sight rails and boring rods at every 100 m wherever necessary including the cost of labour, tools and plants and any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge (In foundations for Alum dosing tanks, bleaching powder dosing tanks, excavation for flow meter chamber, etc. For all 3 WTP’s)

1.1 upto 1.5 m depth cum 30

2

Backfilling with available excavated earth (excluding rock) in pipe trenches, plinth side, foundation of valves or any other structure in layers not exceeding 20 cm in depth, consolidating each deposited layers by ramming and watering with all lead and lift and depth upto 1.5 m including the cost of labours, tools and plants, water or any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge. (In foundations for Alum dosing tanks, bleaching powder dosing tanks, excavation for flow meter chamber, etc. For all 3 WTP’s)

cum 18





Amount (INR)

3

Providing and laying plain cement concrete of M15 1:2:4 grade using approved hard aggregate for PCC using 20 mm and down size aggregate including mixing, laying, tamping, curing and finished for exposed faces including cost of labours, material, tools and plants, curing and any other item require for the completeness of work in all respect complete with all lead and lifts, as per specification and as directed by the Engineer-incharge. (In foundations for Alum dosing tanks, bleaching powder dosing tanks, flow meter chamber, etc. For all 3 WTP’s)

cum 5

4

Providing and laying Reinforced cement concrete of M20 (1:1.5:3) grade using 20 mm and downsize ISI gauge aggregate including cost and conveyance of all materials, formwork/centering, and including machine mixing, laying, tamping, smooth finishing the exposed faces neatly wherever necessary etc., complete as per specification with all lead and lift and cost of labours, tools, tackles, curing etc., and as directed by the Engineer. (In foundations for Alum dosing tanks, bleaching powder dosing tanks, flow meter chamber, etc. For all 3 WTP’s and foundation for Air blower, Backwash pump and constructing Channel for filter wash water at Jangara WTP)

cum 18

5

Providing, supplying and fabricating of reinforcement of all sizes including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position, tying with binding wire of approved quality and gauge including the cost of binding wire and anchoring to adjoining members wherever

MT 2





Amount (INR)

necessary including all laps and wastages etc., with all lead and lifts and cost of labours, tools, tackles complete as per design, specification and as directed by the Engineer.

6

Providing and fixing Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, welding, fixing in position and applying a priming coat of approved steel primer all complete as per design, specification and as directed by the Engineer. (For supporting PVC tube media and alum agitators at all 3 WTP’s and flash mixer at Jangara WTP)

MT 12

7

Plastering in cement mortar 1: 4 (1 Cement : 4 Fine Sand) including removing old plaster and surface preparation including the cost of labours, tools and plants, or any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge. (For structures of all 3 WTP’s)

7.1 12 mm thick internal cement plaster sqm 150 7.2 20 mm thick external cement plaster sqm 300 8 Painting

8.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: including removing old paint and surface preparation including the cost of labours, tools and plants, or any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge. (For structures of all 3 WTP’s)





Amount (INR)

New ( two or more coats) over and including priming coat with water thinnable cement primer

sqm 150

8.2 Finishing walls with water proofing cement paint of required shade: including removing old paint and surface preparation including the cost of labours, tools and plants, or any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge. (For structures of all 3 WTP’s)

New Work (two or more coats applied @ 3.84 kg / 10

sqm) sqm 300

9

Providing and Fixing UV stabilised PVC tube media 1mm thick 1m depth as per specifications and as directed by the Engineer-in-charge. (In Settling tanks of all 3 WTP’s)

sqm 200

10

Providing & filling in Filter sand in filter beds including cost of all materials, labours with all lead and lift, complete as per specifications & as directed by the engineer in charge of works. (In Filter beds of all 3 WTP’s)

cum 250

11

Leak arresting of existing structures by pressure grouting or other approved methods, giving satisfactory hydrotest and making good the surface including cost of all materials, tools and plants, labours with all lead and lift, complete as per specifications & as directed by the engineer in charge of works.

11.1 For 0.67MLD WTP at Batwadi Road (Filter tanks and other structures)

Job 1





Amount (INR)

11.2 For 1.63 MLD WTP at Gufiara (Inlet channel to Settling tanks, Settling tanks, Filter tanks, 350KL CWR and other structures)

Job 1

11.3 For 4.58 MLD WTP at Jangara (Pre-settling tanks, Settling tanks and other structures)

Job 1

12

Making hole in existing RCC side wall of settling tank of Jangara WTP for 2 nos. inlet pipe 150mm dia to be taken from bottom including cost of all materials, tools and plants, labours with all lead and lift, complete as per specifications & as directed by the engineer in charge of works.

Job 1

13 Providing and fixing HDPE dosing Tank suitable for storing chemical solution

13.1 200 lits capacity (For alum dosing and bleaching powder dosing at Batwadi road WTP and Gufiara WTP)

nos. 8

13.2 500 lits capacity (For alum dosing and bleaching powder dosing at Jangara WTP)

nos. 4

14






Amount (INR)

14.1 100mm dia sluice valve PN1.0 (for drain of settling tank at Batwadi road WTP)

nos. 1

14.2 150mm dia sluice valve PN1.0 (for drain of settling tank at Gufiara WTP)

nos. 1

15

Supply, erection, testing and commissioning brand new rotary twin lobe Air Blower of 425 cft/min capacity at 0.35kg/cm2 pressure with air filter, oil filter, silencer, coupling, coupling guard, base frame, pressure and temperature gauges, non-return valve, pressure relief valve etc for air wash of filters complete as per specifications (for air wash of filters at Jangara WTP)

nos. 1

16

Supply, erection, testing and commissioning brand new Horizontal Centrifugal Pumpset 5lps discharge and 18m head with required non-return valve and isolation valves, pipeline fittings, pressure gauge, as per specification etc. complete (for Backwash tank filling at Jangara WTP)

nos. 1

17

Supply, erection, testing and commissioning brand new Alum agitator with SS-316 contact parts as per specification including motor, Gear box, Shaft, paddles, etc as per approved drawing and specifications complete (for alum solution preparation at all 3 WTP's)

nos. 6

18

Supply, erection, testing and commissioning brand new Flash mixer with SS-316 contact parts as per specification including motor, Gear box, Shaft, paddles etc as per approved drawing and specifications complete (at Jangara WTP)

nos. 1





Amount (INR)

19

Supplying, Laying & Jointing of Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and chemical solution, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1 m spacing. This includes jointing of pipe, cost of all materials with all lead and lifts, cost of labour etc. as per specifications and directions of Engineer-in-charge. (piping for alum solution dosing and bleaching powder solution dosing at all 3 WTP’s)

19.1 25 mm nominal outer dia pipes 4kgf/cm2 m 75

20

Providing and fixing 25mm dia PVC ball valve of approved quality 4 kgf/cm2 as per specifications and directions of Engineer-in-charge. (on piping for alum solution dosing and bleaching powder solution dosing at all 3 WTP’s)

nos. 33

21

Supplying, Laying & Jointing of G.I. Pipes of Medium duty Class confirming to IS:1239 (latest Edition) complete with G.I. fittings including trenching and refilling, laying the pipe true to alignment, including cutting and threading of pipe for making up lengths as required for proper completion of work, cost of all materials with all lead and lifts, cost of labour and giving satisfactory hydraulic test, etc. as per specifications and directions of Engineer-in-charge.

21.1 15mm (for water supply to dosing tanks for alum solution and bleaching powder solution preparation at all 3 WTP’s)

Rmt 60

21.2 25mm (for water supply to dosing tanks for alum solution and bleaching powder solution preparation at

Rmt 150





Amount (INR)

all 3 WTP’s)

21.3 75mm (For vent pipe in Slow sand filters at Gufiara WTP)

Rmt 80

21.4 100mm (For fixing of drain valve in settling tank at Batwadi road WTP)

Rmt 10

22

Providing and fixing of Brass ball valve of approved quality (screwed end) 15 mm nominal bore as per detailed specifications and as directed by the Engineer-in-charge. (on water supply line to alum dosing tanks and bleaching powder dosing tanks at all 3 WTP’s)

22.1 15mm dia nos. 12

23

Supplying, laying and jointing of MS specials (Fe-410 grade) of required thickness including tapers, bends, tees, flanges conforming to IS 7322:1985 with latest amendments, perfect linking and welding of joints to correct position. The field welding/ jointing is to be carried out by Manual metal arc process as per IS 816. The electrodes to be used shall be of carbon manganese electrode as per IS 814 duly approved by Engineer-in-charge including cost and conveyance of materials with all lead & lift, cost of labour and giving satisfactory hydraulic test as per IS 3589 for test pressure and working pressure both at factory and at site, complete as per detailed specifications with inside and outside epoxy coating as per IS 11906 specification including loading and unloading of specials etc with all leads & lifts complete including loading & unloading of specials etc. complete as per the approved drawing, tender specifications and as

MT 2





Amount (INR)

directed by the Engineer in charge. (For outlet trough of Pre-settling tank at Jangara WTP, for supporting alum agitator at all 3 WTP’s, etc.)

24

Finishing with Epoxy paint ( two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, cost of all materials, cost of labour, etc. complete On steel work

sqm 100

25

Supply, erection, testing and commissioning brand new Alum dosing box of 0.45mx0.15mx0.15m minimum size of SS 316 construction consisting of SS 316 float valve for maintaining constant head and SS 316 taper needle valve for controlling the dosing rate along with scale duly marked complete as per approved drawing and as directed by the Engineer. (for all 3 WTP’s)

nos. 3

26

Supply and fixing of brand new Bulk Water Meter (Woltmann type cold water meter) of approved make having facility to incorporate RF based wireless remote transreceivers for automatic meter reading. The water meters shall be with removable mechanism, magnetic drive, dry dial, hermetically sealed register, class B type, manufactured in accordance with ISO-4064 standards or equivalent and approved by the Engineer. The meter body shall be flanged end for connection and the bolt hole drilling shall be as per IS 1538. The meter body shall be cast iron as per IS 210 Gr FG260 and shall be coated with a high quality fusion bonded powder coating inside and outside the meter body. The meters shall be equipped with a





Amount (INR)

suitable strainer for longer life of the meter. The meters performance specifications shall be EEC/ISO-4064 Class-B performance. Accuracy shall be in accordance with ISO & EEC class B. The meter shall be suitable to work at working pressure of 10 Bar & temperature of 45 deg C. The meter shall be preequipped for SCADA and suitable communication including CI Sluice valve IVC/ IVI / KBL / R & D/ Kejriwal make as per IS 14846 with latest amendments for Control and cost of specials (puddle flanges, flanged tail piece, Dismantling joint and flanges & necessary reducer and enlargers to fix the Bulk Meters) and jointing materials complete with all lead and lift and as per detailed specifications and as directed by the Engineer Incharge.

26.1 100mm size (for outlet of Batwadi road WTP) nos. 1 26.2 150mm size (for outlet of Gufiara WTP) nos. 1 26.3 250mm size (for outlet of Jangara WTP) nos. 1

27

Providing and fixing Float & board type Level indicator with direct local indication, ±10mm Resolution / accuracy, material of float & guide wire- SS316 & SS304, 6” wide Calibrated Gauge Board, Aluminum White Powder Coating with black Graduation & Numerical type gauge bar as per specification (for 180 KL CWR at Batwadi road WTP, 2 nos CWR at Gufiara WTP and Backwash tank at Jangara WTP)

27.1 Range: 0 to 5 Meter nos. 4

28 Providing and Fixing Loss of head Indicator (0-5m range) for filter beds at Jangara WTP

nos. 2





Amount (INR)

29 Providing and supplying following laboratory equipments at Uttarkashi:

29.1 Jar test apparatus (Four jars) nos. 1 29.2 Conductivity/ TDS meter nos. 1 29.3 Comparator test set for residual chlorine nos. 1 29.4 Hot plates – rectangular with SS top nos. 1 29.5 Magnetic stirrer nos. 1 29.6 Centrifuge nos. 1 29.7 Refrigerator 200 lit capacity nos. 1 29.8 Portable hand held digital pH meter nos. 1 29.9 Electronic weighing balance with weighing box nos. 1


Name of Bidder

Signature of Bidder



Schedule No. D3 - Electrical Works

Unit Rate (INR) Sr. No. Description Unit Qty


1 Civil Work (At Ramleela Maidan)

1.1 Civil work comprising XPM fencing with gate, 150 mm gravel filling, anti-weed treatment to the soil, Cable trenches, precast slabs within transformer yard etc. all lead and lift and cost of labours, tools, tackles as per specifications and as directed by the Engineer.

Job 1

2 Primary Distribution (At Ramleela Maidan)

2.1 Supply, Fabricating & installing following sizes of ladder type hot dip galvanised cable trays with rungs at span of 250mm including horizontal and vertical bends, reducers tees, cross members and other accessories as required and duly suspended from the ceiling/wall with, 40mmx40mmx5mm ,hot dip galvanised suspenders and including painting as required.

Note: Support methods are preferable as follows in different applications as per site requirement. For instance, trapeze supports may be desired in an application where cables will be pulled through the cable tray. Center hung supports, on the other hand, are generally used when cables will be installed from the side of the cable tray. Center hung supports are especially useful when future cable additions are desired. Wall supports and underfloor supports are useful when





ceiling structure is not available or undesired. Outdoor installations are controlled by the structures available to support the cable tray.

300mmx50mmx1.6mm mtr 10

2.2 Supply, Fabricating & installing following sizes of perforated hot dip galvanised cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling/wall with hot dip galvanised suspenders and including painting as required for flowmeter signal transmission at Ramleela and Jangara WTP

150mmx50mmx1.6mm mtr 10

2.3 Supplying and fixing cable route marker with 10cm x 10cm x 5mm thick or of 10cm dia. G.I. plate with inscription thereon, bolted/welded to 35mm x 35mm x 6mm angle iron,60cm long and fixing the same in ground as required for flowmeter and distribution transformer secondary underground cable

No 15

2.4 Design, Supply, Laying, Tieing, Tagging, Testing and Commissioning of 3 core, 240 sqmm 11 kV, 22.6 kA, XLPE insulated, FRLS sheathed, Aluminium conductor, armoured cable in constructed cable trench confirming to IS 7098 with its latest amendments and as per approved make at Ramleela maidan (From 11 kV Lightning arrestor to 11 kV Load Break Switch (LBS) Panel and from LBS

mtr 42





panel to individual Distribution Transformer) Note: Each run of cable will be measured separately and paid.

2.5 Supply, Termination and Commissioning of HV Indoor type heat shrinkable termination kit of approved make complete with all accessories suitable for 3 core 240 sqmm, 11 kV , XLPE insulated ,FRLS sheathed, aluminium conductor armoured cable. It shall withstand the range of ambient temperature experienced in Uttarkashi at Ramleela Maidan

Set 4

2.6 Supply, Termination and Commissioning of HV Outdoor type heat shrinkable termination kit of approved make complete with all accessories suitable for 3 core 240 sqmm, 11 kV, XLPE insulated, FRLS sheathed, aluminium conductor armoured cable. It shall withstand the range of ambient temperature experienced in Uttarkashi at Ramleela Maidan

Set 4





2.7 Design, Supply, Receiving, Storing, Inspection, Handling, Assembling, Installing in correct aligned position, effecting proper Connections, Testing and Commissioning of 11kV/0.433 kV, 3 Phase, 50Hz, 250 kVA, ONAN cooled, mineral Oil filled, Dyn11, copper wound ,approved make, transformer having + 5 % to -15 % On Load Tap Changer ,cable box on 11kV side suitable for 1 Run of 3C x 240 sqmm Aluminium conductor armoured cable and cable box on secondary side suitable for 3R x 3.5C x 300 sqmm XLPE, Aluminium conductor armoured cables. Transformer shall be provided with all the accessories and fittings conforming to IS 2026(Part I-IV) ,ECBC,IS 6600 with its latest amendments and as per approved data sheet. at Ramleela Maidan

Set 2

2.8 Supply, Termination and Commissioning of LV Outdoor type termination kit and accessories suitable for 2 Run, 3.5 core, 185 sqmm, 0.433 kV, XLPE insulated, FRLS sheathed ,aluminium conductor, armoured cable suitable for mounting on secondary side of the 11kV Distribution Transformer

Set 2

2.9 Supply, Termination and Commissioning of LV Indoor type termination kit and accessories suitable for 3 Run, 3.5 core, 300 sqmm, 0.433 kV, XLPE insulated, FRLS sheathed, aluminium conductor, armoured

Set 2





cable suitable for termination at PCC coming from the Distribution Transformer at Ramleela Maidan

2.10 Design, Supply and laying in cable Tray/clamped to wall with suitable clamps, saddles and fixing bolts/ in ground including the cost of digging and backfilling with sand and brick protection as required and including testing and commissioning of the following sizes of 1.1kV grade multicore aluminium conductor XLPE insulated and FRLS sheathed armoured cable conforming to IS : 7098 (Part-I)with latest amendments. The costs shall include properly clamping with cable clamps and ties. Identification tags shall be provided for all cables.

2.10.1 3.5C x 300 sqmm (At Ramleela Maidan Distribution transformer secondary)

mtr 80

2.10.2 3.5C x 95 sqmm (At Jangara WTP Distribution transformer secondary)

mtr 40

2.10.3 3.5C x 70 sqmm (At Ramleela Maidan Capacitor bank feeder)

mtr 40

2.10.4 3.5C x 50 sqmm (At Ramleela Maidan Tubewell)

mtr 80





2.11 Design, Supply and laying in cable Tray/clamped to wall with suitable clamps , saddles and fixing bolts as required and including testing and commissioning of the following sizes of 1.1KV grade multicore copper conductor XLPE insulated and FRLS sheathed armoured cable conforming to IS : 7098 (Part-I)with latest amendments. The costs shall include properly clamping with cable clamps and ties. Identification tags shall be provided for all cables.

2.11.1 4C x 10 sqmm (LDB at Jangara WTP) mtr 20

2.11.2 4C x 4 sqmm (Air blower at Jangara WTP) mtr 30

2.11.3 4C x 2.5 sqmm (At Jangara, Gufiyara and Bhatwadi WTP)

mtr 305

2.12 Supply and making End Termination with heavy duty, approved make ,double compression glands and lugs duly crimped with crimping tool, PVC tape etc. for armoured, XLPE insulated and PVC sheathed 1100 volt grade cables complete as required. (Contractor to verify/confirm quantity) at Ramleela and Jangara WTP

LS 1





2.13 Design, Supply, Receiving, Storing, Inspection, Handling, Assembling, Installing in correct aligned position, 11 kV, 22.6 kA/1SEC, 100A indoor type, approved make, Load break switch (LBS) having 1-incomer and 1-outgoing feeder termination facility, sealed pressure system with SF6 gas, Indicating lamps with fuses, control switch, etc, Voltage presence indication lights in line with IEC 61958 with Earth switch, power contact position indicator, padlocking facility, auxiliary contacts and all other accessories for satisfactory operation as per detail specification, in conformance with IEC 62271, as required by the statutory electrical authorities guidelines and as per reference 11kV Single Line Dwg. at Ramleela Maidan.

Set 2

3 Secondary Distribution

3.1 Motor Control Centre(MCC) at Ramleela maidan





Design, Supply, Installation, Testing and Commissioning of self supported, floor mounted, front operated, cubicle type panel board made out of 14 gauge M.S. sheet complete with following equipments Supplying and fixing of following accessories ,painting ,making interconnections etc. for satisfactory operation as per detail specification , as required by the statutory electrical authorities guidelines and as per reference 415V Single Line Dwg. GW/01/UK-G-016 and GW/01/UK-G-017

Incomer Feeder 630A,25kA,1Sec, MCCB with AC time and

instantaneous Overcurrent, Earth fault and Short Circuit Protection,750/5 A current transformer with analogue ammeter ,voltage selector switch with digital voltmeter ,LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No. Utilisation category A';Ics=Icu

Outgoing Feeder Submersible centrifugal pump motor :-250

A,25kA,1 Sec MCCB, Digital Soft Starter 75 kW(Inside Delta), Comprehensive Motor Protection Relay with LED type Indication lamps for ON, OFF, Auto, Trip, etc. Utilisation category A';Ics=Icu, as per IEC 947(Part2) -one number feeder

Set

2





55 kVAR APFC :- 250 A, 25kA,1Sec, MCCB with Overcurrent, Earth fault and Short Circuit Protection, Single Phase Preventor, selector switch with Digital multifunction meter (kVAR, PF, etc.), LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No. Three phase Power Receptacles/Auxiliary services:- 32A MCB with AC time and instantaneous Overcurrent ,Earth fault and Short Circuit Protection, 40/5A current transformer with analogue ammeter ,LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No.

Lighting DB :- 32A MCB with AC time and instantaneous Overcurrent ,Earth fault and Short Circuit Protection, 40/5A current transformer with analogue ammeter ,LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-2 Nos.

3.2 Power cum Light Distribution board(PDB) at Jangara 4.58 MLD WTP

Design, Supply, Installation, Testing and Commissioning of self supported ,floor mounted, front operated, cubicle type panel board made out of 14 gauge M.S. sheet complete with following equipments

Set 1





Supplying and fixing of following accessories ,painting ,making interconnections etc. for satisfactory operation as per detail specification , as required by the statutory electrical authorities guidelines and as per reference 415V Single Line Dwg. GW/01/UK-G-018

Incomer Feeder 250A,16kA,1Sec, MCCB with AC time and instantaneous Overcurrent ,Earth fault and Short Circuit Protection,200/5 A current transformer with analogue ammeter ,voltage selector switch with digital voltmeter ,LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No. Utilisation category A';Ics=Icu

Outgoing Feeder Centrifugal air blower :- 16 A MPCB with AC

time and instantaneous Overcurrent and Short Circuit Protection, overload range 14-20A,contactor 25A, 20/5A current transformer with analogue ammeter, LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No.

25 kVAR APFC :- 200 A, 25kA,1Sec, MCCB with Overcurrent, Earth fault and Short Circuit Protection, Single Phase Preventor, selector switch with Digital multi function meter (Kvar, PF etc.), LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No.





Lighting DB :- 32A MCB with AC time and instantaneous Overcurrent and Short Circuit Protection, 40/5A current transformer with analogue ammeter, LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No.

Back wash tank pump :- 4 A MPCB with AC time and instantaneous Overcurrent and Short Circuit Protection, overload range 2.8-4 A,contactor 16A, LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No.

Alum mixer, flash mixer, Dewatering pump:- 1.25 A MPCB with AC time and instantaneous Overcurrent and Short Circuit Protection, overload range 0.9-1.25 A,contactor 9A,LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No each.

3.3 Power cum Light Distribution board(PDB) at Gufiyara and Bhatwadi WTP

Design, Supply, Installation, Testing and Commissioning of self supported, floor mounted, front operated, cubicle type panel board made out of 14 gauge M.S. sheet complete with following equipments. IP 43 Double door plain 8 way Supplying and fixing of following accessories, painting, making interconnections etc. for satisfactory operation as per detail specification, as required by the statutory electrical authorities guidelines and as per reference 415V Single Line Dwg. GW/01/UK-

Set 2





G-019 and GW/01/UK-G-020 Incomer Feeder 63A,16kA,1Sec, MCCB with AC time and

instantaneous Overcurrent, Earth fault and Short Circuit Protection, 200/5 A current transformer with analogue ammeter, voltage selector switch with digital voltmeter, LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No. Utilisation category A';Ics=Icu

Outgoing Feeder Lighting cum power DB :- 32 A MCB with AC

time and instantaneous Overcurrent and Short Circuit Protection, LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-1 No.

Alum mixer:- 1.25 A MPCB with AC time and instantaneous Overcurrent and Short Circuit Protection, overload range 0.9-1.25 A,contactor 9A,LED type Indication lamps for 'ON' ,'OFF' and 'TRIP' etc.-2 Nos.

3.4 Local Control Station/Emergency Stop Push Button Station

Supply, Installation, Testing and Commissioning of IP 68, Local Control Station suitable for main 75 kW submersible pump motor sets alongwith necessary mushroom head emergency stop push button to cater inside Delta soft starter driven 3 phase, 50Hz, 415V induction motors.

Set 2





4 Reactive Power Compensation

4.1 Design, Supply, Installation, Testing and Commissioning of 55 kVAr, 415 V, 3Ph, 50Hz, APP, APFC Capacitor Bank with appropriate stages and consisting of modular Capacitor Units Confirming IS 13585 with its latest Amendments with 250 Amp disconnector as Incomer, Over load, S.C & Earth Fault Protection.

Set 2

4.2 Design, Supply, Installation, Testing and Commissioning of 25 kVAr, 415 V, 3Ph, 50Hz, APP, APFC Capacitor Bank with appropriate stages and consisting of modular Capacitor Units Confirming IS 13585 with its latest Amendments with 250 Amp disconnector as incomer with Over load, S.C & Earth Fault Protection.

Set 1

5 Illumination





5.1 Design, Fabrication, Supply, Erection ,Testing and Commissioning of Hot dipped, galvanised steel, octagonal pole conforming to IS: 2713 (part I -III) with latest amendments and with galvanised base plate of size 400mm x 400mm x 7mm in position including excavation of the pit and filling the same with Cement Concrete of M-10 grade (1Cement :3Coarse Sand :6Graded stone aggregate 40 mm nominal size) from base plate to 50cm above ground level, with the help of steel frame not less than 40 cm dia . Duly finished with cement plaster, earthing terminals, cable entry, GI cable sleeve complete as required including excavation and refilling. The pole shall be galvanised and use ISI mark seamless tube for structural purpose. It shall include junction box for terminating 2/3/4 core armoured copper cables upto 4 sqmm. Painting of poles with two coats of red oxide. A coat of bituminous paint shall be provided to the portion to be buried and exposed portion to be applied with two coats of aluminium paints. It shall be as per site requirement and in line with IS 1944 with latest amendments. One number each at Ramleela maidan.

9 mtr Nos. 2





5.2 Supply, Erection, Testing and Commissioning of IP -54 protected, integral, medium/low bay, suspended mounting, luminaire suitable for fluorescent lamp(FTL)lamp comprising of powder coated die cast aluminium housing, electrochemically brightened and anodized aluminium reflector, covered with suitably silicon rubber gasketed heat resistant and toughened clear glass, porcelain holder, integral cast aluminium control gear box having low loss copper ballast, capacitor, electronic ignitor prewired with PVC insulated copper conductor up to corrosion resistant terminal block including making termination etc. as required with lamp. It shall be as per site requirement and in line with IS 3646 with latest amendments. One number each at Ramleela maidan.

2 x 40 Watt Nos. 2

5.3 Supply, Erection, Testing and Commissioning of Industrial type fluorescent tube fitting with fluorescent rod and reflector fabricated from Polycarbonate body and finished with powder coating /virous enamelled complete with all accessories like starter, starter seal, low loss copper ballast, condenser, rotor holder, corrosion resistant terminal block duly wired with copper conductor including making termination etc. as required. It shall be as per site requirement and in line with IS 3646 with





latest amendments. Each at Ramleela maidan and Jangara WTP.

5.3.1 2 x 36 W Nos. 4

5.3.2 1 x 36W Nos. 4

5.4 Supply, Erection, Testing and Commissioning of surface mounting CFL complete with accessories, extra low watt loss copper ballast, starter, holder, condenser, corrosion resistant terminal block duly prewired with copper conductor including making termination as required with lamp. It shall be as per site requirement and in line with IS 3646 with latest amendments.

1x 18W Nos. 2

6 Wiring

6.1 Providing and Wiring of light point/fan point with single core ,1.5 sq. mm ,fire resistant, PVC insulated, copper conductor, 1.1kV grade and single core, 1 sq.mm , fire resistant, PVC insulated, earth copper conductor 1.1 kV grade (IS:694) of approved make in surface / recessed, ISI marked, 20mm GI conduit fixed with saddles and spacers and other accessories, for above false ceiling, or on ceilings, on beams, including flush metal box with earth terminal, neutral looping in switch board, 6 A piano (flush) switch, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws,





cup washers, bushes ,check nuts, making connections, testing etc. as required.(Maximum three switchboard in one circuit-one SP MCB) each at Ramleela maidan and Jangara WTP.

6.1.1 One 6A modular switch controlling one light/fan point

Nos. 10

6.1.2 6A socket outlet with 6A modular switch (on common board)

Nos. 4

6.1.3 6A socket outlet with 6A modular switch (as an independent point)

Nos. 4

6.2

Providing and Wiring of 6/16 Ampere Switch and socket complete with necessary wiring from DB of 2 no of 4.0 sqmm wires and 1 no of 2.5 sqmm PVC Insulated copper conductor wire laying in with 25 mm dia GI conduits of 1.5 mm thick, ISI mark. These will be used with point wiring of power points etc .Each at Ramleela maidan and Jangara WTP.

6.2.1 16A socket outlet with 16A modular switch (as an independent point)

Nos. 4

6.3 Supply, Installation, Testing and Commissioning of ceiling fan of 1200 mm sweep, with speed regulator, fan rod, anchor fastener and all accessories as required. Each at Ramleela maidan and Jangara WTP.

Nos. 3

7 Earthing

7.1 Design, Supply and Laying Pipe in Pipe Earthing in conformance with IS:3043 and

Nos. 24





tested at CPRI with perforated 3.0 Mtr. Long, 25 and 48 mm dia. ' B ' class Zinc coated two mild steel pipe including all accessories such as nut, bolts, reducer, nipple, wire meshed funnel, and making masonry chamber of 450mmx450mmx450mm with mild steel chequered cover and locking arrangement ,embodying the pipe complete with highly conductive and corrosion resistance crystalline mixture plus back fill compound , testing of earth resistance complete as required at Ramleela maidan for Transformer, Double pole structure and lightning arrestor etc.

7.2 Design, Supply and laying following size earth strip/risers as a part of earth grid in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. complete as required to be laid 600mm below ground and for earthing transformer neutral, transformer enclosure, Outdoor ABS, indoor 11kV LBS, 415V MCC, Power distribution board etc. at Ramleela maidan and Jangara WTP.

60mmx10mm G.I. strip mtr 200

7.3 Design, Supply and laying following size earth strips/risers in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection etc. conductor to be on floor, trench and wall for





earthing outdoor lightning arresters, Lighting Distribution Board etc.

25 mm x 3 mm G.I. strip mtr 100

7.4 Design, Supply, Installation, Testing & Commissioning of external lightning Protection as per IS: 2309, IEC:62305 & Indirect Lightning Protection/Surge Protection as per IEC: 61643.

Set 1

8 Safety equipments

8.1 Supplying C02 type, portable Fire extinguishers, of size 5kg each, manufactured from CRCA sheets in all welded construction, body coated with glossy corrosion resistant epoxy powder coating, with inbuilt water proof pressure gauge, with wall bracket, as per IS 2190 and IS 13849 with latest amendments

Nos 5

8.2 Supplying 11kV, B' class, non-skid, high voltage insulation synthetic mat made from elastomeric polymer material, 1000mm wide, 2.5 mm thick, Dielectric strength 45 kV for 1 minute, fire retardant, no adverse effect of transformer oil, diesel, acid, alkali, High Tensile & Elongation properties, good mechanical strength to withstand load and movement of breaker trolley, as per IS 15652 with latest amendments

Sqmtr 5

8.3 Supplying 415 V, A' class, non-skid, high voltage insulation synthetic mat made from elastomeric polymer material ,1000mm wide , 2.0 mm thick, Dielectric strength 3300V for 1

Sqmtr 10





minute ,fire retardant, no adverse effect of transformer oil, diesel, acid, alkali, High Tensile & Elongation properties, good mechanical strength to withstand load and movement of breaker trolley ,as per IS 15652 with latest amendments

8.4 Providing A0 size drawing of SLD in wooden frame with glass. The drawing shall be fully dimensioned and must show HV switchgear, transformer, LV switchboards, protection panels, batteries and battery chargers, fire extinguishers, equipment, storage and drawing holders.

No 4

8.5 Supplying Shock treatment chart, duly laminated in Hindi (Local) and English language.

Nos 5

8.6 Supplying First aid box with all essential medicines including wall mounted bracket

Nos 4

8.7 Supplying 11000 V, Aluminium, anodised Danger caution plate in Hindi (local) and English languages with the sign of skull and bones in signal red colour on front side, as per IS 2551with latest amendments.

Nos 6

8.8 Supplying 415 V, Aluminium, anodised Danger caution plate in Hindi (local) and English languages with the sign of skull and bones in signal red colour on front side, as per IS 2551with latest amendments.

Nos 10





8.9 Supplying Shock proof, Rubber insulated hand gloves, produced through seamless process for minimum working voltage of 11000 V. Should be electricity insulated and tested, should provide dexterity and protection beyond the wrist - length: minimum - 36 cm, white cream colour, soft and flexible quality. With Test Certificate as per IS 4770 with latest amendments.

Pair 2

8.10 Supplying PVC Safety Helmet with PVC head band, made from HDPE thermoplastic. with fully adjustable type head band, sweat band and nylon chin strap. Colour - YELLOW, with logo. As per IS 2925 with latest amendments.

Nos 4

8.11 Supplying Safety goggles made of impact resistant polycarbonate, scratch resistant, 100 % poly carbonate lens and 100% UV protection, Scratch resistant - vision, curved lenses provides 180 degree vision, good impact resistance and adjustable temples for comfort and fitness as per EN-166 with latest amendments.

Nos 1

8.12 Supplying Reusable type, Ear plug smooth and dirt resistant surface, protection for high noise situation upto 105 dBA made from non irritant soft foam base hypoallegic material - smooth surface, universal size, tapered shape, smooth surface fits into all Ear canals and gives comfortable consistent and

Pair 1





protection. Should provide measured attenuation of minimum 30 dB confirm to ANSI S319 with latest amendments.

8.13 Supplying Ear muff with wide headband with padding shall provide firm and comfortable fit, easily adjustable multi-position [over head/under chin/behind head] headband with / without elastic crown strap for individual fit. NRR min 24 dB. CE certified /EN 352 approved / ANSI approval S3.19 / as per IS 6229 with latest amendments.

Pair 1

8.14 Supplying Galvanised mild steel sand Fire bucket with lid and handle, 9 Litres capacity. Buckets to be provided with suitable strand with 4 Nos. hooks to hang sand filled buckets ,as per IS 2546 with latest amendments

Set 2


Name of Bidder

Signature of Bidder



Schedule No. D4 – Environmental Management & Monitoring (Uttarkashi)





Lump sum 1



Per Sample 5





Lump sum 1




23



18







23



54


Per Sample 15


Per Year 15


Per Sample 12


Name of Bidder

Signature of Bidder



Schedule No. E – Devprayag Schedule No - E1- Rehabilitation and Augmentation of Water Supply Scheme in Devprayag Town



Amount (INR)

Sources, Transmission, Distribution Works

1

Supply of Mild Steel Uttaranchal Koop Cylindrical type made from ERW Mild Steel tubes Grade Fe-410 to withstand minimum pressure of 7 MPa and generally as per specification no : 4270 (First Revision) (with latest amendments) duly screwed. Low Carbon Galvanized/ Stainless Steel Grade SS 304 Laterals should be design as per IS:8110-2000 having slot size 1.0 mm with 40% open area. One end of the lateral will be duly screwed and other end will be duly closed as shown in the drawing. Overall length of Uttaranchal Koop should be 1250 mm inclusive of MS Blank Flange and MS Jali. At inlet near 8 cm from one end of MS ERW pipe in cross position horizontal direction plugged with GI Socket duly threaded to accommodate suitably lateral pipe without any leakage. Top end of MS ERW pipe plugged with MS blank Flange, 5 mm thick fitted with nut, bolt and washer, one number socket fitted for outlet near 59 cm from blank

No

3





Amount (INR)

flange at surface of MS ERW pipe along with one number GI Bend of 11.25deg, a jali of 10mm square bar to be fitted into internal portion of ERW pipe near bottom end. Painting with two coat of anti corrosive red oxide paint including all nut bolts and washers complete. All electrically welded joints should be water tight.

1.1

Installing and commissioning of Uttaranchal Koop as per specifications and as per drawings at required locations

No 3

Earthwork

2

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lifts upto 1.5m, including getting out the excavated soil as directed by Engineer with all lead and lift including danger lighting and using sight rails and boring rods at every 100 m wherever necessary including the cost of labour, tools and plants and any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge.





Amount (INR)

2.1 All kinds of soil Cum 9392

3

Demolishing Cement Concrete manually/ by mechanical means including stacking of Steel bars and disposal of unserviceable items by mechanical means, including loading, transporting, unloading to approved municipal dumping ground for all lead and lift as per specifications and as directed by Engineer-in-charge

Cum 100


4


4.1 25mm dia (ID) GI Pipe (Medium duty Class)

Rmt 10000

4.2 100mm dia (ID) GI Pipe (Medium duty Class)

Rmt 1000

4.3 125 mm dia (ID) GI Pipe (Heavy duty Class)

Rmt 13000





Amount (INR)

4.4 150 mm dia (ID) GI Pipe (Heavy duty Class)

Rmt 7000

5

Supplying, Laying and Jointing brand new VAG EKO or equivalent make DI sluice valve conforming to IS 14846 with latest amendments with all lead and lift complete as per specifications and fixing and jointing of DI Sluice valves true to line and gradient, including cost of DI/MS specials, MS specials can be provided only if DI specials are not available (tail pieces, dismantling joints, puddle flanges, flanges, etc.) for the specified diameters including cost of jointing materials like bolts, nuts, rubber insertions, labour etc complete as per drawing and as directed by the Engineer.

5.1 100 mm dia PN 1.6 Sluice valve for 100 mm and 125mm Pipe

No. 4

5.2 150 mm dia PN 1.6 Sluice valve for 150 mm Pipe

No. 2

6

Supplying, Laying and Jointing DI Scour valve 100 mm dia PN 1.6 conforming to IS 14846 with latest amendments with all lead and lift complete as per specifications and fixing and jointing of DI Sluice valves true to line and gradient, including cost of DI / MS specials (tail pieces, Tees, dismantling joints, puddle

No. 6





Amount (INR)

flanges, flanges, duck foot bend, bend, semicircular bend), for the specified diameters including cost of jointing materials like bolts, nuts, rubber insertions, labour, testing etc., complete as per drawing and as per detailed specifications and as directed by the Engineer Incharge.

7

Supply, Laying and Jointing of brand new DI kinetic Double Orifice Air valve approved by the Engineer having small elastic ball resting on gun metal orifice nipple and large orifice vulcanite ball seating ring with built-in kinetic features and rating of PN 1.6 with isolating DI sluice valve of PN 1.6 rating having body, door, dome, gland, non rising stainless spindle, Flanges drilled to IS:1538, valves tested by closed method, mounted in a horizontal position, and operated by metre wheel gearing of approved quality with bolts, nuts, rubber insertions etc. Complete as per drawing and as directed by the Engineer.

7.1 40 mm dia Air Valve PN 1.6 No. 10





Amount (INR)

8

Supply and fixing of brand new Bulk Water Meter (Woltmann type cold water meter) of approved make having facility to incorporate RF based wireless remote transreceivers for automatic meter reading. The water meters shall be with removable mechanism, magnetic drive, dry dial, hermetically sealed register, class B type, manufactured in accordance with ISO-4064 standards or equivalent. The meter body shall be flanged end for connection and the bolt hole drilling shall be as per IS 1538. The meter body shall be cast iron as per IS 210 Gr FG260 and shall be coated with a high quality fusion bonded powder coating inside and outside the meter body. The meters shall be equipped with a suitable strainer for longer life of the meter. The meters performance specifications shall be EEC/ISO-4064 Class-B performance. Accuracy shall be in accordance with ISO & EEC class B. The meter shall be suitable to work at working pressure of 16 Bar & temperature of 45oC. The meter shall be





Amount (INR)

preequipped for SCADA and suitable communication including CI Sluice valve IVC/ IVI / KBL / R & D/ Kejriwal make as per IS 14846 with latest amendments for Control and cost of specials (puddle flanges, flanged tail piece, Dismantling joint and flanges & necessary reducer and enlargers to fix the Bulk Meters) and jointing materials complete with all lead and lift and as per detailed specifications and as directed by the Engineer Incharge.

8.1 100 mm dia No. 1

8.2 150 mm dia No. 1

9

Providing and laying PCC of M15 (1:2:4) grade using 20 mm and down size aggregate laid in 15cm thick layers and well compacted, vibrating, curing, finishing with necessary cement mortar (1:4), excluding formwork and centering, and including all lead and lift and cost of labours, tools, tackles and curing as per specifications and as directed by the Engineer. (For Retaining wall, Weir, Pipe supports, anchor/thrust blocks, valve chambers etc.)

Cum 65

10

Providing and laying Reinforced cement concrete of M20 grade using 20 mm and downsize ISI gauge aggregate including cost and conveyance of all materials

cum 245





Amount (INR)

excluding formwork, and including machine mixing, laying, tamping, curing etc., complete including smooth finishing the exposed faces neatly with CM (1:4) proportion wherever necessary etc., complete as per specification with all lead and lift and labours, tools ,tackles as directed by the Engineer (Exclusive of cost of steel and fabrication charges) (For Retaining wall, Weir, Pipe supports, anchor/thrust blocks, valve chambers etc.,)

11

Providing, supplying and fabricating of reinforcement of all sizes including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position, tying with binding wire of approved quality and gauge including the cost of binding wire and anchoring to adjoining members wherever necessary including all laps and wastages etc., with all lead and lifts and cost of labours, tools, tackles complete as per design, specification and as directed by the Engineer.

kg 8900





Amount (INR)

12

Providing Centering and shuttering including strutting, propping etc. and removal of formwork for reinforced concrete works and including cost of labours, tools, tackles as per specification and as directed by the Engineer.

sqm 1600

13

Providing and laying Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including all material, labour, lead & lift, as per specification, as per drawing and as directed by the Engineer.

Cum 300

14 Providing and laying 4 kg/cm2 PVC Pipe of 75mm dia for weep hole including all labour, all lead & lift, etc. complete

Rmt 100

15 Providing and laying filter media of aggregate size 20mm for weep hole etc. complete

Cum 1

16

Backfilling with available excavated earth (excluding rock) in pipe trenches, plinth side, foundation of valves or any other structure in layers not exceeding 20 cm in depth, consolidating each

Cum 8453





Amount (INR)

deposited layers by ramming and watering with all lead and lift and depth upto 1.5 m including the cost of labours, tools and plants, water or any other item required for the completeness of work in all respect as per specification and as directed by the Engineer-in-charge.

17

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of 50 KL Clear water Reservoir as per required design using RCC construction with all necessary arrangements, water level indicator etc all complete as per drawing and as directed by the Engineer.

L.S. 1

18

Soil investigation, conducting SBC and Design, supply, Construction, testing, commissioning of RCC Framed structure (Normal Building) floor height 3.35 mtr. for Office Building as per specification for area atleast 400sqm for office building (G+1).

Sqm 400

19

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of RCC Framed structure (Normal Building) floor height 3.35 mtr. for Guest House building as per specification for area atleast 100sqm for Guest House building (G Floor Only)

Sqm 100





Amount (INR)

20

Soil investigation, conducting SBC and Design, supply, construction, testing, commissioning of RCC Framed structure (Normal Building) floor height 3.35 mtr. for Staff Quarters Building as per specification for area atleast 200sqm for Staff Quarters Building (G+1)

Sqm 200


Name of Bidder

Signature of Bidder



Schedule No. E2 – Environmental Management & Monitoring (Devprayag)





Lump sum 1



Per Sample 5





Lump sum 1




23



18







23



54


Per Sample 15


Per Year 15


Per Sample 12


Name of Bidder

Signature of Bidder



Schedule No. - Grand Summary of Bid Price

Amount (INR) SI.No. Schedule No. and Description

In Figures In Words

Schedule No. A (Rudraprayag)

1 Schedule No. A1 – Rehabilitation and Augmentation of Water Supply Scheme in Rudraprayag Town

2 Schedule No. A2 - Environmental Management & Monitoring .

3 Provisional Sum 3,100,000

Schedule No. B (Karnprayag)

4 Schedule No. B1 - Rehabilitation and Augmentation of Water Supply

Scheme in Karnaprayag Town

5 Schedule No. B2 - Electrical and Automation works (Karnaprayag)

6 Schedule No. B3 - - Environmental Management & Monitoring


Schedule No. C (Gauchar)

8 Schedule No. C1 - Rehabilitation and Augmentation of Water Supply

Scheme in Gauchar Town

9 Schedule No. C2 - Electrical and Automation works (Gauchar)

10 Schedule No. C3 - Environmental Management & Monitoring




Amount (INR) SI.No. Schedule No. and Description

In Figures In Words

Schedule No. D (Uttarkashi)

12 Schedule No. D1 - Rehabilitation and Augmentation of Water Supply

Scheme in Uttarkashi Town

13 Schedule No. D2 - Rehabilitation of Uttarkashi WTP's

14 Schedule No. D3 - Electrical Works

15 Schedule No. D4 - Environmental Management & Monitoring


Schedule No. E (Devprayag)

17 Schedule No. E1 - Rehabilitation and Augmentation of Water Supply Scheme in Devprayag Town

18 Schedule No. E2 - Environmental Management & Monitoring


GRAND TOTAL to be carried forward to Letter of Bid

Name of Bidder

Signature of Bidder

Section 4 B– Bidding Forms

Supply, Laying, Jointing of Transmission Mains and Design, Construction of Infiltration Well, WTP and GLSR etc.