Building Your PC_ Installing Internal Cards and Case Cables

8/6/2019 Building Your PC_ Installing Internal Cards and Case Cables

http://slidepdf.com/reader/full/building-your-pc-installing-internal-cards-and-case-cables 1/6

0

Welcome to the Celtnet How to Build your PC: Installing internal cards and case cables

Search:

Welcome to Celtnet's How to Buld your Own P C Page — This is the sixth page in a series of articles that takes you through the main components

of a PC, how they work and how you can put them together to either build or upgrade your own PC. This is an illustrated guide and by following these

instructions you can learn how to build, repari and upgrade any PC. If you would prefer not to wade through several web pages, the entire series is avaialble as the

, sales of which go to support the . Here you will see how to install the internal cards and

attach the case cables.

Building your PC:Installing internal cards and case cables

Introduction

In of this series on building your own PC you saw how to install all the internal drives into the case. We're now going to look at how to istall add-on cards t

the motherboard and how to attach the various cables from the case to the motherboard. I usaully start by checking where everything is and from there I plan wha

to attach first and how.

Page Map

Installing the Internal Car ds

Getting Started:The case I'm using for this build has front panel audio inputs. These have to be attached to the rear of the motherboard in a place

indicated by the red box to the left. This lies between the AGP slot where the graphics card will go (right-hand arrow) and the ISA

slot where my modem card will go (arrow to the left). Because of the location it will be essentially inpossible to get to the audio

connectors if both the graphics card and the modem ar in place. As a result I have a little bit of a problem; and this is where someforethought comes in.

Connection points for the other case cables are located near the bottom left hand corner of the motherboard and thus are far away

from the problem areas and need not be considered until later. Looking at what I need to do I think the easiest way to proceed is to

install the graphics card first, then the audio cables and then the modem card.

With this plan in mind, I could proceed with the installation.

Hom e Build you r ow n PC Cr eate a W ebs ite Build PC eBook Ch eap PC Com ponen ts PC Ar ticle s Char ity C am paign

Advanced S earch

How to build a PC eBook One Milion People Ch arity Campaign

part 5

Getting Started System Panel Header

Insta lling th e Graphics Card Conclusion

Atta ch in g th e Soun d Ca bles Join the Mailin g List

IDE Modem Card

Front Panel USB Cables



Installing the Graphics Card: All add-on cards (such as the graphics cards) bring new functionality and connectivity to your PC. As a result they need to

communicate with the outside world. To achieve this the communication ports of the cards project through specially-designed port

at the back of the case; ports that are shown in the image to the left. These ports also have screw holes in them that allow the

expansion cards to be affixed firmly into place, as will be demonstrated below.

The image on the left shows the MSI GeForce FX5200 graphics card that I've chosen for this

particular build. The card is an 8x AGP card that fits into the AGP slot on the motherboard.

Notice the tang on the base of the card to the right. This is used to securely hold the card in place

and is an important part of the card's design. You should also just be able to make out the ports

on the front face of the card. It is these that project through the back of the case, with the metal

bracket being used to support and affix the card to the case.

The image to the left shows the AGP slot (top). Note the tilt lever on the right hand side of the slot. Thi

attaches to the tang on the graphics card and you should make certain that it's set in the downward

position. Inserting the card will eventually push this switch up and lock it into place. Note also that th

slot is assymetric so it's only possible ot insert the card one way (though the way to insert the card

should be obvious because of the case's rear ports!).

Inserting the card into the slot is simply a case of aligning the card with the rear slot and easing it into

the AGP socket. The bottom image on the left shows the card in position, but not yet secured. Once thi

is done, simply push down on both sides of the card and it should easily click into place.

The image on the left shows the graphics card inserted into the motherboard. You should be able to see that the

metal bracket of the card sits flush against the back of the case with the connection points on the card

projecting from the back of the case. By this point the card should be sitting securely in its slot and the next

stage is to affix it in place.

Once the card is seated securely in its socket the next stage is to affix it it properly to the case. This is done with a screw

(which is usually the same size and shape as the screws that affix the case's side panels to the case body). Simply align

the hole or notch in the card bracket with the hole in the card hole at the back of the case and then screw this into place

The screw shold go in easily. If it doesn't then your card is probably mis-aligned. Once the screw goes fully home then

your graphics card is securely attached.

With this done, you have now securely attached your graphics card to your motherboard.



Attaching the Case Sound Ca bles: As already mentioned above, because of the relative positions of the sound headers, the AGP slot and the IDE slot, after installig the graphics card the

next task is to insert the cables from the front of the case that attach to the audio connectors.

The image on the left shows the front pannel conectors of the case. As you can see there's an audio out jack for headphones or speakers, an audio in

jack for a microphone and two USB connectors for easy access to removable devices such as cameras.

This means that there are two audio cables to attach to the audio headers on the motherboard.

The image on the left shows a schematic of the pin configuratinon for the

external audio header (top left) as well as the way the pins actually look on the

motherboard (bottom left) and it a lso shows the two audio cables to connect the

stereo output jack and the microphone input jack.

You can see from the schematic that the connection pins for the microphone

input are all clustered on the top of the audio header (these correspond to the

lower of the two cables above. As a result it's easiest to attach these first and

then to attach the audio output (speaker) cables.

The leftmost image here shows the microphone input cable attached to the

motherboard. This only leaves the audio output cable to be attached. On this th

long flyleads to the Left and Right channel backout leads. The image to the righ

shows the audio header with both cables attached. This completes the

installation of the external audio connectors.

IDE Modem Car d As previously discussed, the IDE headers on the motherboard (white above, left) lie to the very left of the AGP

card into which the graphics card has already been inserted. You can see the modem card to the left. It's really

only included here as it was a card that I already had and it's easier to insert now whilst I'm putting the entiremachine together rather than having to tackle it again later. As you can see, the IDE header on the motherboard

is assymetric so that it's only possible to insert the card one way.

Though, as with the AGP card it should be obvious which way the card fits as the metal plate on the back of the

card must f it against the back of the case so that the telephone sockets are available at the back of the computer

The use of a modem card may well be more than a little dated these days. However, it can sometimes be very

useful in an emergency and it also demonstrates how to insert an IDE card (which are still fairly common

peripheral card types).

Inserting the card is a question of fitting the metal plate against the back of the case and seating the card loosely

on top of the IDE header.



If seated correctly then inserting the card should be a relatively simple matter of

pushing down on top of the card so that it drops firmly down into the slot of the

IDE header. Once the card is seated properly, then attaching it to the case is just a

matter of inserting a retaining screw and securing it firmly in place.

In the image to the left you can see how the cables for the case sound sockets go

under the modem card, which was one of the reasons for the assembly sequence

chosen above.

With the IDE card in place, all the internal components of the PC build have now

been installed and we can return to the remaining connections from the case.

Case Cable Connections

Apart from the audio connetions (dealt with above) the other case connections all link to essentially the same are of my motherboard.

The image on the left shows the remaining motherbaord headers (boxed in red).

On the left lies the main motherboard header whilst on the right is the blue

header for the front panel USB sockets. First I'll attach the USB cables (mostly

as these are easier).

Front Pa nel USB CablesThe image to the left may be a little busy, but in concept it's fairly simple. The

image to the bottom left shows the USB headers on the motherboard and the

image top left shows a schematic of these connectors indicating what each pin

does. Basically the top row is for one USB connectoin and the bottom row is for

another. The image top right shows one of the two USB connectors that connecto the front of the case. You will see that each of the little plugs is labelled with

GROUND (corresponding to GND on the pin diagram), VCC (corresponding to

USB_PWR on the diagram), and +D and -D, respectively (corresponding to

P+6 and P-6 on the diagram). Fixing the cables is simply a matter of attaching

the correct cables in the correct sequence. With a little care and attention this i

actually fairly simple to achieve and when done correctly you will have the

cables for both USB connections attached correctly as in the image on the

bottom right.

With the USB cables connected we now only have the system panel headers to

attach.



Sy stem Panel HeaderThe final stage of attaching the various case cables is to attach the standard

front panel connectors to the motherboard. These are the connectors for the

case's power switch, its reset switch, the case's power LED and the LED which

shows that the hard drive is being accessed. Depending on your case you may

also have a system speaker cable (though this was not present on my system).

The image top left shows how the cables attach to the pins on the motherboard

and the motherboard header itself is shown bottom left. The cables and

connectors that need to be attached are shown top right. For my case the white

cable on each connector represented the negative lead (marked - on the

schematic). Once I'd identified the cables it was a fairly simple process to match

the cable to the description of it on the schematic (such as POWER SW

matching to PWRBTN#) and then to plug it into the motherboard in the

appropriate position so that I attained the image on the bottom right. I tend to

work from the left hand edge of the header to the right as it's then easier to see

what's going on and more difficult to make an error as a result.

Conclusion With all the internal cards affixed and all the case cables attached to the motherboard the installation process is now very nearly complete. However, there are

few clean-up processes to go through (such as affixing fans and checking connections) and we'll go through these as well as the initial power-up phases in the

.

Below you will find links to other pages dealing with Building and Upgrading your PC

Building Your PC

Main PC Components

nex

article in this series

Getting S tarted

The Main Components

Gettin Started on the Build

Assembling and I nstalling the Motherboard

Installing the Internal Drives

Installing Internal Cards and Case Cables

Installing Fans and Configuring

Upgrading your PC

Operating Systems and Software

Free PC Software

Open Source Software

Case

Central Pr ocessing Unit

CD and DVD

Fans

Floppy Disk



Building and Upgrading you r PC PDF file — It takes time and money to keep The Information Site on the world wide web. You can help via the PayPal donation

system:

You remain anonymous as all eMail details are destroyed once your gift has been verified and a 'thank you' email has been sent. I need your trust and do not keep or

sell eMail addresses. Once your donation has been made you will receive a copy of my Build and Upgrade your PC PDF fi le which takes you through the main

components of your PC along with how to chose those components and how to build a PC from them, all in a pictorial guide. Any donation you make goes towards the

that aims to make a number of old and ancient culinary texts freely available on the web. For more information see the

. Also, if you purchase a book through any of the Amazon links below then a portion of the price will go to the maintenance of this site. Thank you

for your help in keeping 'Celtnet Information' running.

Remember the name: Celtnet.org.uk

Copyright Nemeton 2004-2010. All rights reserved.

Graphics Card

Keyboard and Mouse

Motherboard

Network Cards

Network Cards2

Monitor

Printer

Power Supply Unit

Sound Card

One Million People campaign Frequently

Asked Questions

Documents

Building Your PC_ Installing Internal Cards and Case Cables