Upload
others
View
3
Download
1
Embed Size (px)
Citation preview
Projects, Techniques, and Products
MORE TO MAKE:
TECHNIQUES:
Flame finish
■ Cigar box guitar ■ Mobile clamp cart
■ Teaching Table: a 1st class project
■ Laminating Legs: Thin stock? No problem.
■ Ten tips for better table tops
■ Build better boxes with a benchtop jig
BURN YOUR PROJECTS!
Score big with a FOOTBALL CUTTING BOARD
44
October/November 2018 | Issue 85
Projects
Tools & Techniques
26 Score Big with a Football Cutting BoardMonday nights just got a little tastier. Kick off the season with this
clever snack server that’s sure to please any football fan.
36 Teaching TableYep, build this table, and you’ll learn mortise-and-tenon joinery, leg tapering at the
table saw, shaping curved components, correct glue-up procedures, and more.
44 Build a Box GuitarWood never sounded so good! This fresh interpretation of a cigar box guitar
contains some fine joinery and plenty of other features that a musician will love.
58 Compact Clamp CartTurn a sheet of 3⁄4" plywood and a half-sheet of 1⁄2" plywood into a roll-
around clamp corral with shelves for your other shop essentials.
30 10 Tips for Better Table TopsA table’s top is its starring component. Here’s some great advice
to make sure that it plays its lead role to perfection.
54 Flame FinishShou sugi ban is woodburning at its most exotic. Who would have
thought that torching and brushing oak would create a luxuriously
textured surface that’s resistant to water, bugs, and even fire!
Table of Contents
36
2
04 Contributors/ On the Web
06 Getting Sharp• Table Matters
08 Profiles• Jory Brigham
10 News & Views• Mistakes make us great
• Hearing aid protection
• Turn for Troops celebrates
15 years of giving
14 Hot New Tools• Bessey GearKlamp
• Jet 14" Bandsaw JWBC-SFX
18 Tips & Tricks• A quick corner rout
• Mags to hold bags
• Morse taper as jam chuck
• Microfiber grain detector
• Marking gauge wheel
sharpening
66 Great Gear• Cheap and easy
edge protection
• Defying gravity
• A little saw
with big benefits
68 Buyer’s Guide
69 Ad Index
70 Expert Answers• Proper angles for dovetails
72 Outfeed• The Final Gift
Cover photo: John Hamel
Departments 5826
30
54
1608
Oct/Nov 2018 | woodcraftmagazine.com 3
he football cutting board
on page 26 comes from
an impressive collection
of man-cave projects that
designer/woodworker
Jim Harrold has developed
since retiring as editor
of Woodcrat Magazine
three years ago. Jim sells
his creations through
galleries in Hawaii, where
he likes to vacation.
Jim’s writing and
editing career began
in the early 1980s,
when he joined Better
Homes & Gardens
Meredith Corporation to produce a series of
DIY books and magazines. Later, he became
the Executive Editor of WOOD magazine,
and then joined Woodcrat LLC to head up
its woodworking publication. When he’s not
designing or building an original project,
you’ll catch Jim on a Kona ishing boat in hot
pursuit of an Ahi (yellowin tuna) or marlin.
Contributors
If you’ve been reading the magazine, you’ve seen Rob Spiece share
his expertise on making small boxes, lattening slabs, recovering from
woodworking mistakes, and more. his issue’s contributions (Flame
Finish, p. 54; Teaching Table, p. 36, 10 Tips for Better
Tabletops, p. 30) are further evidence of the woodworking (and
writing) talents that Rob continues to cultivate at the JD Lohr
School of Woodworking. Outside the shop, Rob has taken up a new
activity with kids Sid and Laura: ishing. “We’ve been out about
10 times so far,” Rob says. He also enjoys hanging out with wife
Andrea, and tearing up the racquetball court with anyone who
wants to play an opponent with workshop-strengthened forearms.
“My dad bought me a used ShopSmith™ for my 14th
birthday,” says Doug Stowe (Box Guitar, p. 44). “I turned
pro in 1976. Between furniture commissions, I made boxes
to keep busy. My irst box guitars were made with students
at the Clear Spring School, in Eureka Springs, Arkansas.”
Today Doug continues to teach woodworking in
the Clear Spring School, and at crat schools and
woodworking clubs throughout the country. He’s
authored 12 books (including his latest “Box Maker’s
Guitar Book”), several DVDs, and dozens of articles
on woodworking and education. Doug lives on a
forested hillside in Eureka Springs, Arkansas. ■
On the WebOn the Web
Jim hauled in this
105 pound Ahi on a
recent trip off the Kona
coast. Poké anyone?
Doug (far left) teaches box-making skills across the
country. This one took place last summer at the
Connecticut Valley School of Woodworking.
When not teaching woodworking
classes, Rob builds custom
furniture at the Lohr Studio, in
Schwenksville, Pennsylvania.
Extra extras. This issue is
packed with bonus content.
We have projects, techniques,
patterns, and templates for just
about everything in the issue.
Check out our website to read
the extras online, or download a
free PDF. There’s even a video
of Rob’s flame finish in action.
Survey Says!? Well, actually, that’s
up to you. Check out our online survey
to give your opinion, and let us know
how we’re doing. All you have to do is
go to woodcraftmagazine.com. You’ll
see the survey link at the top of the page. It takes
only a moment to complete, and your answers will
help shape the content of your favorite woodworking
magazine. (That’s us, by the way. Right?) ■
4
Afew years ago, I took the
“Practical Woodworking” class at
he JD Lohr School of Woodworking
in Schwenksville, PA. At the end of the
week, I had a nice-looking table for my
home and a wealth of knowledge for
my shop. he curriculum touched on
just about everything from how a tree
grows to how to
apply a inish. I
gained valuable
experience and
made fast friends
with the instruc-
tors and my
fellow students.
My instructor
Rob Spiece wrote
the article on page
36. You can build
the same table at
your own pace and
in the comfort of
your own shop. Essential skills like lami-
nating legs, creating mortise & tenon
joinery, and making a table top (p. 30)
are inherent in the table’s construction.
Making the table top was a hard-won
lesson for me. My top was dead lat and
looked perfect until I sliced through a
biscuit while crosscutting to size. he
ix? Make a smaller table. I sliced sliver
by sliver to keep as much length to the
top as possible. And then I had to resize
the long aprons and recut their tenons,
but the table turned out great in the end.
Former staf designer Shayne Hiles
and I both earned a spot on the school’s
instructively entertaining Wall of Shame.
Me for my biscuit blunder, and Shayne
for gouging his top. I learned my lesson,
and never made
that mistake again.
Taking the class
was an enriching
adventure, so it was
fun to stroll down
memory lane as we
produced this story.
It’s been years since
I built the table, but
the skills I learned
have proved useful
in many other proj-
ects. I encourage
you to check out
the story even if you know these basics,
as it could be a good refresher course.
And who knows? You may learn a new
way to tackle a certain technique, opening
yourself up to new ideas that you can take
to your shop for your next project. ■
Getting Sharp
Oct/Nov 2018 Vol. 14, Issue 85
Chief Editor: Chad McClung
Senior Editors: Paul Anthony, Joe Hurst-Wajszczuk
Consulting Editor: Tim Snyder
Art Director: Bobby Schehl
Publisher: Gary Lombard
Advertising Sales Manager: Vic Lombard
Circulation Support: Kim McLaughlin
Office Manager: Connie Harmon
Circulation: NPS Media Group
Contributing Designer: Kelli EdmanWeb Support: Jessica LoyerVideo Producers: Frank Byers, Kevin Reed
Graphic Design Intern: Jon Liebau
Subscriptions: (U.S. and Canada)One year: $19.99Single copy: [email protected] (800) 542-9125
Woodcraft Magazine ( ISSN: 1553.2461, USPS 024-953) is published bimonthly (Dec/Jan, Feb/Mar, April/May, June/July, Aug/Sept, Oct/Nov) and printed in the United States. Periodicals postage paid at Parkersburg, WV, and at additional mailing offices.
POSTMASTER: Send address changes to Woodcraft Magazine, P.O. Box 7020, Parkersburg, WV 26102-7020.
Canada Post: Publications Mail Agreement #40612608
Canada Returns to be sent to Pitney Bowes,
P.O. Box 25542, London, ON N6C 6B2
©2018 by Woodcraft Supply, LLC. All rights reserved.
Woodcraft Supply, LLC allows the purchaser of this magazine
to photocopy the included projects and techniques solely for
personal use. Any other reproduction of these projects and
techniques is strictly prohibited.
Safety First! Working wood can be dangerous. Always make
shop safety your first priority by reading and following the
recommendations of your machine owner’s manuals, using
appropriate guards and safety devices, and maintaining all
your tools properly. Use adequate sight and hearing protection.
Please note that for purposes of illustrative clarity, guards and
other safety devices may be removed from tools shown in
photographs and illustrations in this publication.
Table mattersWe love hearing from readers! And there are all
kinds of reasons to get in touch with the crew at
Woodcraft Magazine. Check out the details below.
General information:
4420 Emerson Ave., Suite A
P.O. Box 7020
Parkersburg, WV 26102
800-542-9125
Share a slick tip to win cash or a prize.
Here’s your chance to help someone become
a better woodworker and get rewarded for the
effort. The winner of next issue’s Top Tip award
will receive a Woodcraft Gift Card worth $250.
All others will receive $125 for a published illustrated
tip or $75 for a non-illustrated tip. Published tips
become the property of Woodcraft Magazine.
Email us at [email protected] and
put “Tips & Tricks” in the subject line or visit
woodcraftmagazine.com, and click on Contact.
Important: Please include your phone number,
as an editor may need to call you if your
trick is considered for publication.
Have a tough woodworking question?
We’ll do our best to find the expert and provide the
answer. Email us at [email protected]
and put “Expert Answers” in the subject line.
News & Views:
This catch-all column is where we do our best
to correct mistakes, publish feedback from readers,
and share other noteworthy news items. It’s easy to
participate in this discussion. Just email us at
put “N&V” in the subject line.
Submit an article idea:
Do you have a story idea? We’d love to hear about it.
To find out how to submit an article, email us at
[email protected] and put
“Submission” in the subject line.
Share photos of your projects:
We’d like to see what you’re building. To show off your
work send your photos to [email protected],
or find us on social media.
Share your ideas.
Wall of Shame. My buddy Shayne
and me accepting our mistakes
and our place on the wall.
6
WM: �ree words to
describe Jory Brigham?
JB: Stubborn, driven,
and…diicult.
WM: Describe your design
aesthetic to someone who’s
never seen your work.
JB: Well, I can only tell
you what I would hope
it is. I hope my designs
stir emotion. Whether
it be curiosity, comfort,
happiness, or my favorite,
nostalgia. I try to include
diferent styles, eras, and
even cultures into my pieces.
I love to hear people say
that my designs remind
them of their grandparents’
furniture. hat was back
in the day when people
bought furniture with
an intent to hand it
down to their children.
hey weren’t scared to
invest in something that
would be a part of their
family for generations.
WM: What’s the one thing
you wish people knew
about making furniture?
JB: If you truly love
woodworking, part of
your soul goes into every
piece you make. here
are so many diferent
approaches to furniture
making. Everybody does it
diferently. hat’s how you
get one-of-a-kind creations.
How much of one’s self
can go into a piece of
furniture made on a CNC
machine or by a robot?
WM: What makes
working with your
hands so satisfying?
JB: hat is a deeper question
I am not really capable of
answering. I can only say
that it is fulilling to create a
tangible piece that afects the
people around us. Working
with your hands can be
an opportunity to create
something unique from your
whole being – physically,
mentally, and emotionally.
hat’s rare these days.
WM: What’re the
best and worst things
about teaching
woodworking classes?
JB: he best thing is the
people we meet at the
school. And I love the
diferent ways that the class
impacts my students and
gets them creating. Getting
people to think in a non-
conventional way is so cool.
he worst thing is the huge
mess that we make in class.
WM: What kind of
people take your class?
JB: We get men and women
ranging in age from
17-70. Some students are
cabinetmakers looking
Profiles
Jory Brigham Making modern furniture, with nostalgic aspirations
West Coast furniture maker and woodworking
teacher Jory Brigham has a modern take on
nostalgia. He designs pieces with mid-century lair
and the idea that furniture should last. And Jory
believes that anyone can ind their individual style.
You just need to do two things: Work with your
hands and don’t let adulthood erase the creativity,
curiosity, and energy you have as a child. Although
he grew up in a family full of cratsmen, Jory still
managed to cut a swath all his own, creating an
impressive variety of furniture collections that have
attracted clients from all over the country. Remark-
ably, Jory also inds time to teach woodworking
classes at his workshop in Paso Robles, California.
I had the opportunity to visit with Jory, and meet
his wife Alison, daughter Parker, son Bozley, and
a menagerie of pets that include snakes, chickens,
lizards and other critters. Here are some highlights…
—Lori Harper
8
to learn new techniques,
while others are just getting
started as woodworkers. We
also get a lot of people from
Silicon Valley—computer
engineers and computer
programmers. I never knew
there was such a correlation
between that kind of work
and woodworking.
WM: What advice would
you give your younger self?
JB: Don’t be in a hurry to
think like an adult. hinking
like an adult can kill your
imagination and slow
your growth as a designer
and cratsman. And you
may garner the wrong
lessons from otherwise
helpful experiences. he
thing that saved me is
that I took forever to act
like an adult. I still have
trouble recognizing things
I should be afraid of. And
it takes me far too long
to learn my lesson. Being
naive and stubborn kept
me thinking that someday
I would do what I loved,
even though I didn’t know
how to get there. If I had
known how hard it was
going to be to make it as a
professional woodworker,
I may have just quit.
WM: What does it
sound like when you’re
alone in your shop?
JB: Peace.
WM: What task seems
never-ending?
JB: Sanding.
WM: What is one thing
you allow yourself to
spend money on?
JB: Tools. ■
Furniture photos: Ron Bez Photography, Profile photo: Christa Renee
Thinking like an adult can kill your imagination and slow your growth as a designer and craftsman.
onlineEXTRAVisit our website and click on onlineEXTRAS
for more of my conversation with Jory.
—LH.
See Jory’s furniture line at www.jorybrigham.com.
To sign up for classes, go to jorybrighamworkshop.com.
Oct/Nov 2018 | woodcraftmagazine.com 9
News & Views
Mistakes make us greatI wanted to compliment you
on your editor page “Getting
Sharp” (page 6, June/July
2018, issue 83). I am retired
and can relate to every
word. I can also most
certainly relate to the
Wood Filler article, called
“Great Mistakes,” on
page 72. he two articles
tie together nicely.
I am sure there
are millions of
woodworkers who feel as I do: If I
could make one piece of furniture without a mistake,
it would be a real miracle. I didn’t realize until I read the
article what a mistake, along with an ingenious ix, could
mean to me. Robert Spiece did a masterful job in making
me feel like one of the best woodworkers in the world.
I have now decided to start a business of making
mistakes and inding the ix. hat way I will always make
the perfect piece of furniture. he only thing I haven’t
igured out is how to keep people from feeling dumb for
making another stupid mistake. Every time I mess up, I
think, “How could I do such a stupid thing as that?”
From now on when I make a stupid mistake, I will yell
aloud, “Fantastico!” hen I will spend the necessary time
plotting some ingenious plan to ix it, and none will be the
wiser until I brag about how I did it as pointed out in Robert’s
article. hank you for such an upliting way to call attention
to the mistakes we make and what they really do for us.
—Robert Laferty, Munfordville, Kentucky, via email
Rob Spiece replies:
I’m glad the essay struck a chord. here’s
certainly no one among us who can’t relate.
Maybe take a beat before you dive head irst into
your best mistakes. Rather than elation, I encourage
you to continue with the familiar feelings of rage
and disappointment ater screwing something up.
hat “stupid” feeling we get is essential to turning
the mistake into a learning process, so I don’t
think we want to lose that. Save your exclamation
of “Fantastico!” until your problem is solved.
hanks so much for the note…I think I’ll spend
a few moments “reveling in my own genius”!
10
Hearing aid protectionWhile reading the Aug/Sept 2018 issue, I saw the
letter from a reader concerning hearing aids and
working in the shop. You requested suggestions
from your readers, so I am submitting mine.
During service in Vietnam, I lost the high
frequencies in my let ear. hanks to the VA, I
have two wonderful digital hearing aids. When I
retired and began working daily in my shop, I too
was concerned about doing damage to my hear-
ing aids, especially when operating my thickness
planer. I used to wear shooter’s headsets, what we
called “Mickey Mouse” ears in the military. hey
worked but they were hot and blocked out all
noises, so I couldn’t hear the phone or my wife.
Last year I purchased a set of noise-canceling
headphones, and that did the trick. Now I can
keep my hearing aids in, hear the shop sounds,
and even answer my cell phone while wear-
ing the headphones. It was the perfect solution
for me and I hope it will help someone else.
—Michael J. Schoield, via email
Senior Editor Joe Hurst-Wajszczuk replies:
hanks for writing, and most importantly,
thank you for your service to our country.
here’s a lot of truth to the saying, “If it
works for you...” however, it’s important
to point out that “noise canceling” is not
the same as “hearing protection.”
here are dozens of products that claim
to be “noise canceling” but do not carry
an ASTM rating. hese products might be
great for plane trips or listening to music
at the gym, but woodworking is a diferent
situation. Believe it or not, some “noise
canceling” headphones can exceed safe-
listening thresholds while playing music,
actually contributing to hearing loss.
To work efectively in a workshop situation,
hearing protection must have the ability to
instantly block out loud noises (e.g. the shot of
a pneumatic nailer or the scream of a router).
Otherwise, you might be causing damage
every time you pull a trigger or lip a switch.
he device must have this ability in addition to
its digital technology. hat way, it can provide
protection even when the battery is dead. ■
Turn for Troops celebrates 15 years of givingVolunteers and Woodcrat employees have turned more
than 160,000 wooden pens for the Turn for Troops program,
which celebrates its 15th year in 2018. hose pens have
been sent to U.S. military personnel on active duty and
recovering in rehabilitation centers, along with personal
notes from the turners. One major responded, “hank
you from the bottom of my heart. It is Americans like
you who make old soldiers like me proud to serve.”
In continued recognition of our troops, pen turning
events will be held at most Woodcrat stores over
Veterans Day weekend, November 10-11. No experience
is necessary to participate; folks of all ages are welcome
to join in this event for our military forces. All you need
is a desire to say “thank you” to a servicemember.
—Lori Harper, Special Projects
Manager for Woodcra�, LLC
Email [email protected]
-or-
write to Woodcraft Magazine, 4420 Emerson Ave., Suite A,
Box 7020, Parkersburg, WV, 26102-7020.
Important: Please include your full name, address, and phone
number. Published letters are edited for length and clarity.
How to reach us
News & Views
12
Hot New Tools
Clamp with a new twistBessey GearKlamp
Overview• Available with 6-, 12-, 18-, and 24"-long bars.
• 23⁄8" throat depth
• 450 lbs. stated clamping force
• Retail price ranges from $15.97 to $24.97
Traditional F-style clamps are
a ixture in most woodshops
for good reason. hanks to
their stone-simple design,
these clamps reliably deliver
pressure wherever it’s needed—
most of the time. Whether
you own a few clamps, or
your collection numbers in
the dozens, odds are good
that you’ve encountered a few
situations where the handle
got in the way. With their
new GearKlamp, Bessey has
found a clever way around the
problem. By repositioning the
handle on the steel bar, they’ve
created a clamp that can reach
into spots where others can’t.
To eliminate the traditional
handle with its threaded screw,
Bessey managed to hide a
geared drive in the clamp’s
bottom jaw. To apply clamping
pressure, you make your initial
adjustments by depressing
the release button and sliding
the moveable jaw against
your workpiece. hen twist
the handle to advance the jaw
pad, which has a ¾" throw.
he clamp operates very
smoothly. Applying pressure
was easier, in fact, than with
my smaller-handled F-style
clamps, and much easier than
with one-handed trigger-
style clamps. And despite the
internal gear mechanism,
the GearKlamp weighs only
slightly more than its cast-
metal counterpart. his is
probably because the jaws
are made from a iberglass-
reinforced composite.
GearKlamps cost 1½ to 2
times more than traditional
F-clamps, but I suspect that,
like me, most woodworkers
would consider this a
reasonable upcharge for a
clever solution to diicult
clamping problems.
—Tester, Joe Hurst-Wasjszczuk
Button releases jaw.
See the Buyer’s Guide on page 68 for ordering and pricing information.14
GearKlamp vs. Standard F-style clamp
Jaw pad
Handle
Moveable jaw houses gear mechanism that drives clamping pad with a twist of the handle.
Photos: Ralph Lee Anderson Oct/Nov 2018 | woodcraftmagazine.com 15
Hot New Tools
Jet’s new 14" bandsaw enters a tool category with a large
number of competitive models. But this saw has some
innovative features that woodworkers will appreciate,
especially with regard to heavy-duty resawing. For
starters, there’s just over 13" of resaw height, and the saw
can accept ¾" blades. Independently adjustable upper
and lower ball bearing guides provide excellent blade
stability, while an enclosed base and heavy-duty tubular
steel construction provide plenty of mass; the saw weighs
over 300 lbs. Jet’s product design team made room for an
oversize table (17" × 21½") to handle large work, and a
re-engineered trunnion system that makes it easy to tilt
the table for angled cuts. A pair of 4" dust ports helps to
maximize dust extraction. he saw comes with a top-
quality miter gauge and an aluminum fence that can be
used horizontally or vertically (like the old Delta Unifence).
he 6"-high vertical mode is excellent for resawing. ■
—Tim Snyder
New bandsaw is a heavyweight contender Jet model JWBS14-SFX
FIRST LOOK
Photos:Doug Loyer
Versatile fence. Jet’s design
allows for horizontal (low) or
vertical (resawing) orientation.
Strong and stable.
Heavy-duty guides and 3⁄4"
blade capacity enhance
resawing performance.
16
A quick corner routWhen making shelves and small table tops, I like to
radius the corners for both aesthetics and safety. I
ind that the most eicient and consistent way to do
it is using a template on a table router outitted with a
lush-trim bit. A pair of fences on the template allow
for quick, accurate positioning of the workpiece. Make
the template from a piece of ½" hardwood plywood,
shaping one of the corners as desired with a jigsaw
or bandsaw. If necessary, smooth and fair the proile
by iling and/or power-sanding. Attach two fences as
shown, keeping them back from each end of the curve
by a couple of inches so they don’t impede bit travel.
To shape your workpiece, irst trace its corners using the
template, then saw to within ⅛" of the line. Install a lush-
trim bit with a shank-mounted bearing into your table
router, and adjust the projection of the bit so the bearing
contacts the pattern. Holding the workpiece irmly against
the template fences, trim the corner to shape, making sure
to move the workpiece against the rotation of the bit.
—Marvin Mertz, Baton Rouge, Louisiana
Tips & TricksTips & Tricks
Illustrations: Christopher Mills
Attach fences a couple inches back from corner.
Plywood template with finessed corner
Rough-cut to within 1⁄8" of traced cut line.
Feed workpiece against bit rotation.
18
Oct/Nov 2018 | woodcraftmagazine.com 19
Tips & Tricks
Mags to hold bagsChanging the bag on my dust collector
always made me wish I had four hands—two
to hold the bag in place, and two to replace
the metal holding strap. Since I’m unlikely
to grow an extra set of mitts, I decided to
put a couple of ½"-diameter rare-earth
magnets into play for the job. I screwed
commercially available steel cups to the
ends of short dowels to hold the magnets
in place. hey temporarily hang the bag in
place while I apply the strap. Works great!
—Ed Williams, Makawao, Hawaii
Use magnet to hold bag in place while installing steel band.
Steel band
Screw
Steel cup
1⁄2" × 1" dowel 1⁄2"-dia. rare earth magnet
Dust collector bag
20
Tips & Tricks
Here’s your chance to help
someone become a better
woodworker and get rewarded
for the effort. The winner of
next issue’s Top Tip award
will receive a Woodcraft
Gift Card worth $250. All
others will receive $125 for a published
illustrated tip, or $75 for a non-illustrated tip. Published
tips become the property of Woodcraft Magazine.
Send your ideas to:
Tips & Tricks, Woodcraft Magazine,
P.O. Box 7020, Parkersburg, WV 26102-7020
-or-
visit woodcraftmagazine.com, and click on “Contact”.
Important: Please include your phone number, as an editor
may need to call you if your trick is considered for publication.
Share a Slick Tip. Win Cash or a Prize!
Morse taper as jam chuck
Microfiber grain detector
Here’s an easy way to make custom-sized dowels on a
lathe using squared stock that’s too small to hold with a
spur or jawed drive chuck. Just remove the chuck, and
use the Morse taper in the drive spindle as a jam chuck of
sorts. (A #2 Morse taper will snugly accommodate a ⅝"-
square blank.) Push one end of a wannabe dowel into the
tapered recess, center other end on the tailstock, and turn.
—Mikey Panicky, Ventura, California
With certain woods that lack distinct graining, it
can be diicult to gauge which direction to plane in
order to prevent tearout. In these cases, I’ve found
that dragging a microiber cloth on the surface is
very helpful. With most woods, there’s a noticeable
resistance when the cloth is pulled against the slope of
the grain. So, whichever way the cloth moves easiest,
that’s the direction you want to move the cutter.
—�omas Moss, Bradenton, Florida
22
Tips & Tricks
Marking gauge wheel sharpeningI love my wheeled marking gauge but, like
any other cutting tool, it needs occasional
sharpening to work efectively. he darned
wheel is so small, though, that it can be hard
to hone. Ater abrading my ingertips,
I discovered that a standard wooden
pencil with eraser works great to scrub
the wheel on my honing stones. ■
—Mark Hassleblad,
Los Angeles, California
Wheeled marking gauge
Eraser powers cutter over honing stones.
24
Oct/Nov 2018 | woodcraftmagazine.com 25
FOOTBALL CUTTING BOARDEarn extra points on game day with this special server.
By Jim Harrold
With a little bit of walnut and maple, you can crat a cutting board
that’s sure to be a big hit with any football fan. Cutting the cross
stitch slots in the joining halves of the football blank involve
a technique that is similar to making inger joints, and the nity trick
for bending and applying the maple stripes allows the walnut football
shape to expand and contract without restriction. Now let’s give this
project a proper kickof.
Order of Work• Glue the lace strips and spacers to one
half, and lay out the cross stitches.
• Cut slots for the stitches, glue the halves
together, and tap the stitches in place.
• Make the stripes and lay out the football.
• Shape the football and add the feet.
• Load it up with tasty snacks,
and enjoy the game.
Score Big with a
Opening photos: Larry Hamel-Lambert
X X
26
Two halves, with cleverly cut notches
Quarter FootballHalf-Size Patterns
Laces and Stitches
onlineEXTRAFor full-sized drawings of the template
and laces and stitches pattern,
go to woodcraftmagazine.com.
1 square = 1"
Illustrations: Dan Thornton
CROSS STITCH1⁄4 × 1 × 11⁄4"
STRIPE1⁄4 × 1 × 63⁄16"
LACES(See detail below.)
Stopped hole7⁄8"-dia. 1⁄4"D.
DOWEL FOOT7⁄8"-dia. 5⁄8"L.
FILLER STRIPS1 × 1⁄2 × 37⁄8"
1⁄4" roundover
Dado1⁄4 × 1"
81⁄2"131⁄4"
3⁄4"
1"
he iconic football shape is created using walnut for the
football and maple for the stitches and stripes. For stability
and looks, I used ritsawn stock with straight grain as
opposed to the cathedral grain of latsawn boards. I cut
both halves from the same board for the best grain match.
Each half is notched at the table saw to make the
cross stitches, and then glued together. Shallow
dadoes on the top make room for the stripes.
he feet are cut from a walnut dowel rod.
7⁄8" Hole
1⁄4"
1⁄4" 3⁄8"1⁄2"
11⁄4"
61⁄4"
Oct/Nov 2018 | woodcraftmagazine.com 27
Add lengthwise stitches to one walnut half, then cut notches for cross stitchesPlane a 5 × 30" length of walnut and a 2 × 12"
length of maple to 1" thick. From this stock,
rip a ½"-wide length of the walnut for the iller
strips, and two ¼"-wide lengths of maple for
the laces. (his will mimic the ine seam of
the laces on an actual leather football.) For
safety and accuracy, I used a featherboard at
the table saw using a zero-clearance insert.
Now lay out the slots for eight cross stitches.
Tape together the halves keeping the ends
lush. Mark four cross stitches on each side of a
cross grain centerline. hese slots require two
separate cutting sessions at the table saw. Once
all the slots are cut, glue the halves together.
hen cut and install eight cross stitch pieces.
Deeper slots in the wider half. Separate the halves from
each other and raise the cutter to 7⁄8". Now, finish cutting
the cross-stitch slots in the wider half that contains the
lengthwise lace parts, registering on the slots cut earlier.
A rectangular football. Use the 1"-wide cross-stitch pieces as
indexing keys to ensure precise alignment. Once fully clamped and
aligned, remove the keys to prevent them from being glued in place.
Use moistened cotton swabs to remove glue in the slots. Finally,
glue in place the cross stitch pieces and sand them flush when dry.
Indexing key
Make the football blank
WALNUT HALVES1 × 4 × 14"
WALNUT FILLER STRIPS1 × 1⁄2 × 37⁄8"
MAPLE LACES PIECES1 × 1⁄4 × 61⁄4"
Shallow slots in both halves. Install a 1⁄4" dado set in your
table saw and set the cutter height at 3⁄8". Put the halves together
with double-stick tape, making the ends and inside edges flush.
Attach a wood auxiliary fence to your miter gauge to eliminate
tearout. Align the slot layout with the cutter, clamp, and cut.
28
Stripes, curves, and finish…Touchdown!
Bend the stripes. Clamp the ends of
the maple stripes over a small dowel and
heat the center of each piece with a heat
gun to form a permanent bend in the wood.
Shape the football. Cut the blank to
shape, sawing just outside the lines. Use
a disc sander to remove saw marks and
achieve a smooth, accurate edge. Chuck a 1⁄4" roundover bit in your router table, and
round-over the top edges of the cutting
board using a pair of push pads for safety.
Dadoes for the stripes. Using a dado set
and a miter gauge with an auxiliary fence
and a stop, cut 1⁄4" deep × 1" wide dadoes
across the top face of the cutting board.
Lay out the football shape. To center the
football outline on your blank, strike one
line between the long lace strips, and a
perpendicular line centered between the two
middle stitches. Set the template against the
centerlines and trace each section as shown.
Lay out the football’s 1"-wide stripes ¾"
from the end of the laces. Extend the
lines onto the edges to align the dado
cutter, and cut the dadoes as shown.
Size two pieces of maple to it the
dadoes. I give the stripe pieces a
permanent bend along their lengths
and apply glue to only the middle
two inches, clamping the concave
faces into the dadoes. he pressure
created by the bend keeps the stripes’
top faces lush to the cutting board,
allowing for wood movement.
Now the football will start to take
shape. Copy the Quarter Football
Template (p. 27), and trace the shape
as shown. Cut out the shape, and
then sand and round over the edges.
Make the feet from ⅞"-dia.
dowel rod. Just cut four ⅝"-long
pieces, and glue them into ¼"-deep
holes drilled with a Forstner bit.
I sanded the entire football through
220-grit and applied mineral oil. It’s
almost time for kick-of. Load up
your cutting board with your favorite
game-day snacks and enjoy. ■
Stop
Quarter template
Project photos: Marlen Kemmet Oct/Nov 2018 | woodcraftmagazine.com 29
They all add up to a
stunning surface.By Robert Spiece
onlineEXTRAS• Jointer Fundamentals
• Composing with Grain
10 Tips for Better TABLE TOPS
What’s it take to
make a table top?
You just edge-glue
a few boards together, sand ‘em,
and there you go, right? Not so fast.
Not if you want something that looks
great and represents quality workman-
ship. Ater all, a table’s top is its most
prominent feature. Sure, it’s basically
just a panel, but you can screw it up
any number of ways by mismatch-
ing boards, milling them incorrectly,
or improperly joining them, among
other errors. If you want to create table
tops that dress up rooms in style, and
that show people you know your stuf
when it comes to woodworking, check
out these 10 time-tested techniques.
30
Photos: John Hamel
A good table top starts with good material. If you can, buy
boards graded FAS (irsts and seconds). An FAS-graded
board must be at least 6" wide, 8' long, and 83.33% free of
knots and defects (depending on the species). Unfortunately,
many small mills don’t sort by grade, in which case you’ll
just have to do the best assessment you can on your own.
Your stock should be close to lat in the rough. Crook,
minor bowing, and cupping can all be dressed out, but
seriously bowed or twisted boards are almost always a bad choice
because they tend to sufer from indomitable internal stresses.
Also, dressing out the warp oten leaves insuicient thickness.
For the 15-½"-wide table top at the bottom of page 32, I needed
a board at least 8" wide and twice as long as the top. hat way,
I could use a single piece for the whole panel, which helps
in getting a good grain and color match right at the start.
It’s not all about workability, though. Also look for a board
with the potential to be a beautiful table top. Before cutting the
board down, scrutinize its edges, considering where to create the
seam. For a natural transition, arrange to join straight-grain to
straight-grain edges if possible, and try to avoid abutting edges
with grain runout, which can create a visual clash at the seam.
Stare it down.
Sight down a candidate
board to check for
crook and bow. This
crook can be ripped
away, and there’s
very little bow, so it’s
in promising shape.
No propellers. A twisted board presents milling
problems, and should generally be avoided for table
tops. Twist is easily detected by sighting across the
tops of winding sticks : a pair of straight sticks of
contrasting color placed at the ends of a board.
Start with good material1
Getting a good grain and color match
is much easier if you’re working with a
�itch, which is a series of sequentially
sawn boards from the same tree.
A litch can be costly, but it’s well
worth the bookmatching opportunities
that can create high drama in a
glued-up panel. With the walnut litch
shown here, I’m careful to locate my
edges so my book match lines up on
all of the boards that will comprise
the tabletop. Picking a couple of
identifying marks like small knots
or streaks helps me keep the boards
aligned. In the case of these pieces,
I measured in from the waney edge.
Flitch it if you can2 A matched set. There’s no better way to
ensure grain and color consistency than
to use only boards from the same tree.
These walnut slabs will be judiciously
milled and edge-joined to create a simple,
but singular, rectangular table top.
Oct/Nov 2018 | woodcraftmagazine.com 31
Switch, flip, and slip to make a match from a random batch
When composing a table top from
random stock, enjoy the puzzle! Take
advantage of your myriad potential
matches by trying every possible
combination of boards in every possible
orientation. Try to work with the low
of the grain. With latsawn boards, take
advantage of the straight grain typically
found on either edge to make a panel
with blended seams. he cathedral
patterns in the centers of such boards
can be artfully arranged, even though
such a multi-board constitution will
never mimic the grain of a single plank.
If you’re bookmatching a tabletop,
a seam in the center makes sense.
However, I’m oten trying to make up
one uniied panel without bringing
attention to the seams. In that case,
using an odd number of boards and
keeping the seams of-center will help
to randomize the look, leading to a
more visually natural composition.
Some woodworkers claim that
alternating the heart face and sap face on
adjacent boards will “equalize” a panel,
ensuring a latter surface, but I’ve found
this to be a myth. Instead, compose the
visually best surface, and rely on the panel’s
attachment to the table base to keep it
lat. Use denatured alcohol as shown
to bring out the natural color tones.
In the near photo at right, I arranged
the seams to incorporate the sapwood
as a design element. In order to achieve
this efect successfully, it’s important
to use the sapwood from both mating
edges to form a natural transition.
Otherwise, the colliding heartwood
and sapwood would create a hard,
straight, visually ruinous glue line.
Once you have a pleasing
arrangement, be sure to view it from
all sides and angles. Depending on
the way the grain is laying, it can
relect light diferently, especially
with igured material. I’ve been
surprised on multiple occasions
when the top looked perfect
when viewed from one end, but
completely wrong from the other.
So just do your best to make
the most pleasing arrangement
possible. And don’t fret if you don’t
get it “perfect.” Keep in mind that
wood is a natural material and will
only bend to your will so much.
You’ll oten need to rip a board down to minimize
cupping or just to suit your jointer’s capacity. But
before ripping, consider where the kerf is going to
fall, and the ⅛" or so of wood that will be lost to it.
Ater the rip, and ater jointing both edges, you may
lose close to ¼" of wood to the cuts. If you’ve sliced
through the slope of cathedral grain, the interruption
is likely to be obvious when the edges are rejoined.
It’s best to choose a path through straight grain,
where the joint usually comes back together without
a trace of a glue line. If your straight grain doesn’t
fall in the right place, try bisecting the peaks of the
cathedral pattern, which will tend to rejoin nicely.
When rejoining ripped sections, don’t be afraid
to shit the parts to achieve the best match. his is
particularly a good approach when trying to reestablish
cathedral grain low. It helps to leave yourself as
much extra length as possible to make this work.
Also, try to use natural variations in color to
create an artful arrangement. Notice the two dark
streaks lanking the center seam in the photo
at far right. his creates visual interest that also
helps draw attention away from the joint.
Locate rips to minimize grain disturbance
Don’t interrupt. This panel is constructed from
one 8'-long board that was crosscut in half,
aiding color- and grain-matching. Each half
was then ripped to alleviate cupping. Board #1 was ripped
through a straight-grained section, while board #2 was ripped
through the tips of the grain cathedrals. At the center of the
panel, the two boards meet with a straight-grain-to-straight-
grain joint, which makes the seam nearly undetectable.
Ripped through straight-grained section
Chalk triangle registers orientation of boards.
Board was marked for easy reorientation after ripping.
Ripped through cathedral peaks
Board #1
Board #2
PANEL LAYOUT
GLUED-UP PANEL
Straight-grain-to-straight-grain joint
3
4
32
Alcohol enhanced. When working with random boards, do your best to integrate color and grain into one solid
composition. Wipe and/or spray denatured alcohol onto the surface to pronounce both grain and color in order to get
the best possible match. At left, the lighter sapwood meets at the seams, drawing attention to them, but also providing
visual interest. At right, the opposite faces of the same boards join to create a cohesive heartwood composition.
Lay out to avoid tearout
Make sure to keep track of your individual
boards’ grain direction throughout the planing
process and aterward. If you don’t, you risk
accidentally edge-joining them together with
opposing grain directions, which invites tear-
out when planing the inal, composite panel.
I mark the feed direction on every board as it
exits the planer. If I notice tear out, I’ll reverse
direction on the next pass. If the tearout is
reduced, I mark the leading end of the exiting
board with “GD” for “good.” his label means
“Only plane this board in this direction, or you’ll
be sorry.” For example, the crotch grain on the
board next to the planer in the photo below
looks beautiful as is, but if fed in the opposite
direction it would be chewed up beyond repair.
he most beautiful boards will oten struggle
in both directions. he notations made at the
planer help me to work with the lesser of two
evils and minimize clean-up ater the glue up.
Marked for travel. Chalking
the leading end of a properly
oriented board as it exits the
planer ensures that you won’t
accidentally feed it the wrong
way on the next pass, inviting
tearout. You’ll need to re-mark
after every pass, so keep the
chalk handy as you work.
Joined edges are nearly invisible.
5
woodcraftmagazine.com 33
Pipe clamps ofer plenty of power to close an edge joint, while helping to keep
the table top lat under pressure. I place the clamps over and under, making
sure that the pipes contact both faces of the panel in order to keep it lat. Look
for a nice, even bead of squeeze-out along the entire length of each joint.
I use strips of wax paper to prevent black iron stains on the
“show” face of the top. I use the bandsaw to cut these little 2"-wide
rolls from a standard roll of supermarket wax paper.
Careful clamping and clean-up. Placing half of the clamps on top of
the panel assembly equalizes the tendency of the panel to cup under
pressure. On the “show” side of the panel, I scoop up the wet excess glue
with a putty knife, then remove the upper clamps one at a time to clean up
each unimpeded section in turn with clean water. Finally, I protect against
black stain by placing a strip of wax paper under each reapplied clamp.
Nothing beats a jointed edge for making
perfect seams. In my experience, even table
saw blades that purportedly create a “glue line
rip” don’t really create the kind of neat seam
I’m interested in. Joint all mating edges, then
do a dry clamp to ensure absolute closure. I
like to test the joint using a light-duty “F-style”
clamp. If it closes the joint perfectly, I know
that pipe clamps will have no problem. Be picky
at this stage, and make sure each joint closes
perfectly. To help detect the ofending edge in
a gap, slide one board past the other. If the gap
moves with the board, rejoint that edge. If the
gap stays in place, rejoint the opposite board.
Feed with care. A successfully jointed edge depends on proper feed
technique, especially with longer boards. Make sure to press the face of
the board firmly against the jointer fence, and maintain leading end contact
with the outfeed table. If the board is short enough, begin with your hand
on the trailing end so that you can feed in one uninterrupted stroke.
Make things easier on yourself by
working to the capacity of your planer.
For example, to make a 44"-wide
dining table top, I’ll begin by gluing
up two separate 22"-wide panels from
boards that I planed slightly oversized
in thickness. hen, ater planing both
assembled panels to almost-inished
thickness on our 24" planer, I have
Use a jointer!
Stagger your clamps and clean up the panel’s show face Plane in parts
6
8 9
34
For table tops under 30" long, a simple edge joint
is easy to assemble and plenty strong. For longer
table tops, I use biscuits as alignment aids to bring
adjacent board faces lush. hey won’t create a dead-
level seam, but they’ll get you pretty close. I start my
biscuit layout 4" in from the end to prevent exposing
a biscuit when crosscutting the top to inished
length. Lay out and cut your biscuits 8-12" apart
Don’t get sloppy with the slotting, as an
angled biscuit may actually force your boards
out of alignment. I keep my hand planted
irmly down on the joiner’s fence, with the
edge of the board overhanging my bench to
ensure unimpeded contact with the tool.
Alignment aid. Biscuits help align boards during the glue-up.
When joining the boards, I typically apply glue to only one edge of
each joint and to all of the slots, but not the biscuits themselves.
Sanding isn’t the best option for leveling
seams. A belt sander works in theory,
but the reality is usually fraught with
divots and tracks. And a random-orbit
sander will ride up on the high spots,
producing an uneven surface. It’s best
to attack the seams with hand planes
and cabinet scrapers, which will create
a much latter surface. Start planing
at a diagonal with a jack plane, using
a straightedge to gauge your progress.
hen plane diagonally again, but at
90 degrees to your original direction.
When your straightedge indicates a
relatively lat surface overall, plane
parallel to the grain. hen switch to a
smoothing plane and scraper to clean
up the previous plane track marks.
Don’t worry about creating a glass-
smooth surface at this point, just
get it to the point where a random-
orbit sander can take over. ■
only have one seam to deal with
in my inal glue-up. You can
apply the same idea to smaller
planers. Gluing up separate
parts irst, rather than gluing up
the entire panel at once, might
seem like an extra step, but you’ll
thank yourself when it comes to
leveling the inished surface.
Fill that mouth. Glue up
a table top in sections
whose widths approach
your planer’s capacity.
This reduces the amount
of work needed to flatten
the finished panel after
the sections are joined.
Flatten first. A sander typically
won’t take out the humps and
valleys on a joined-up panel;
you really need to use a jack
plane for that, first working
diagonally to the grain, then
parallel to it. Follow up by
scraping, and then sanding
to smooth the surface. Scraper clean-up. A card scraper
does a great job of removing
plane tracks, and needs only
fine-sanding as a follow-up.
Plane and scrape before sanding
Biscuit long boards
10
7
Oct/Nov 2018 | woodcraftmagazine.com 35
Te chingTABLE
t the JD Lohr School of Wood-
working, we use this hall table
project as a vehicle to teach
fundamental approaches to furniture
making. By building this piece, you’ll
learn a slew of great techniques that will
give you a jump start in your wood-
working education.
For example, when making the top,
you’ll learn how to glue up a strong panel
with attractively composed grain. Same
thing for the legs; whether you’re cut-
ting them from 8/4 stock, or laminating
them to thickness, I’ll show you how to
achieve visual harmony on all the faces.
he technique for tapering the legs will
also serve you when making many future
tables. As for the aprons, you’ll discover a
simple, time-honored trick for laying out
their curves, and a neat planing trick for
fairing their edges ater cutting.
For the best in structural integrity and
longevity, you won’t ind this piece con-
structed with screws, but with venerable
mortise-and-tenon joinery. I’ll show you
how to make these joints to ensure that
your work stays together for generations.
And the glue-up process will teach you
an approach you’ll use on many similar
tables and other pieces.
So welcome to class! And, hey, even if
you already know all this stuf, you still
end up with a ine looking table that will
sit pretty in any room of the house.
APRON3⁄4 × 41⁄2 × 341⁄4"
Sawn curve initially begins here, and is faired by hand afterward.
END APRON3⁄4 × 41⁄2 × 111⁄2"
TOP7⁄8 × 151⁄2 × 43"
Lesson 1:Laminating LegsSee p. 38.
Lesson 3:Cutting perfect tenons See p. 40.
Lesson 4:Tapering legs with a jigSee page 41.
A “furniture making fundamentals” course
built into a popular projectBy Robert Spiece
11⁄8"
7"
2"
36
Photos: John Hamel; Illustrations: Christopher Mills
Order of Work• Make the legs.
• Rout the leg mortises.
• Cut the tenons.
• Taper the legs.
• Shape the aprons.
• Glue up the table.
onlineEXTRAS• Mortising Jig
• Tapering Jig
• Batch-cut Buttons
LEG13⁄4 × 13⁄4 × 291⁄8"
Button7⁄8 × 1 × 21⁄2"
Button mortise1⁄2 × 3 × 3⁄8"
1⁄4" R. roundover
3"
15⁄8"
Mortise3⁄8 × 35⁄8 × 7⁄8"
Centered tenon3⁄8 × 3 × 3⁄4"
3⁄8"
Taper begins here.
7⁄16"
Lesson 5: Laying out apron curvesSee p. 41.
Lesson 6: Making great table topsSee p. 43.
Lesson 2:Routing mortises with a jig See p. 39.
Lesson 7: Flame finishSee p. 43.
Strong stylehis table derives its strength
primarily from the rock-solid
mortise-and-tenon joinery
that connects the aprons
to the legs. he solid wood
top attaches to the aprons
with L-shaped wooden
“buttons” that allow the
panel to expand and contract
seasonally across the grain.
he tapered legs and arched
side aprons provide style
to accompany solidity.
Note: Apron dimensions include tenons.
Oct/Nov 2018 | woodcraftmagazine.com 37
Laminating table legsMaking table legs by laminating stock requires a
thoughtful approach to prevent an unsightly collision of
grain at the seams. Here’s a great technique for creating
four 1¾"-square legs from one 4/4-thick board. hree
of the legs will have book-matched grain on one face,
and one leg will have custom-matched grain. (hat is,
lay them out the best you can.) Use the most straight-
grained sections of the board to create attractive legs.
Joint edge to go against table saw fence.
Mark ends of boards to realign them later.
Mark 2" sections.
Avoid wild grain when possible.
Crosscut 4/4 × 7" × 8' roughsawn board into three 30" sections. Cut away ends to remove checks.
To be custom-matched (CM) To be book-matched (BM)
Rip 1: Saw 2"-wide piece.
Rip 2: Saw 2"-wide piece.
Rip 3: Adjust fence to rip outer edge straight.
Feed direction Discard the custom-matched piece with the least-straight grain.
Rip 4: To capture straight grain near outer edge, rotate board, reset fence to 2", and rip here.
CM BM BM
Orient concave faces inward.
Add layout lines and leg number.
Next Steps: Joint concave faces, plane opposite faces, then glue-up.
CMBMBMBM
BM face BM face BM face CM face
Step 1: Mark non-laminated face, hold it against squared jointer fence, and joint a laminated face.
Step 2: Mark jointed laminated face.
Step 3: Rip opposite faces to 3⁄32" oversized.
Next Steps: Plane leg to finished size, then crosscut to finished length.
A
A
A
B
B
B
C
C
C
1
2
3
4
5
38
Pretty legs require thought
Joinery begins with the mortises
Begin by making the legs, as this
is where the joinery layout starts.
If you make your legs from 8/4
stock, prefer rit-sawn sections,
which will display relatively
straight grain on all faces. Avoid
sections with wide cathedral
grain. Unfortunately, 8/4 stock
isn’t always available, in which
case you’ll need to glue up each
leg from two pieces of 4/4 stock.
he igure (facing page) shows
you a great way to create four
matching legs that don’t call
loud attention to their seams.
he photos below demonstrate
a quick, accurate method for
crosscutting the legs to length.
Determine the best orientation of the legs,
and mark them as shown to indicate their
relative positions. hen lay out the mortises
where shown in the drawing on page 37. If you
use a good mortising jig, you need only lay
out two mortises as shown below, center.
Alternatively, you could do the cutting simply with
a router outitted with an edge guide, in which case
you’ll need to lay out one mortise in full, and then just
the end lines for the rest. Jig or not, rout to a ⅞" depth
(⅛" more than the tenon length) in a series of passes no
more than about ⅜" deep to prevent stressing the bit.
Quick, safe crosscutting. To cut each leg to length, I first square up one end (left), and then register that end against a 2" spacer
block sitting against my rip fence to make the second cut (right). Employing a spacer like this allows use of the fence’s scale
(adding 2"), but creates clearance between the workpiece and the fence for a safe crosscut that won’t jam and kick back.
Pretty, good order. Arrange
the dimensioned legs so that
the straightest grain will be
on the most prominent faces.
Then number them 1 & 2 at
the front, and 3 & 4 at the rear
for easy re-orientation later.
Jig-ready. If you use a good mortising jig, you need lay
out only two mortises, as the jig will then automatically
register the others. Still, make sure to mark the other
mortise faces with chalk to avoid set-up confusion.
A good mortising jig. The mortising jig we use
in our class (See onlineEXTRAS) automatically
registers the position of the legs in the jig for
quick, accurate routing of the mortises.
2"-wide spacer block
Oct/Nov 2018 | woodcraftmagazine.com 39
Precise tenons visit the saw, then a hand planeI cut the tenons at the table saw
using a ¾" stack dado, setting up
the cut with a test piece milled to
the precise thickness of my apron
material. I register the tenon length
using the fence and my 2" spacer
block. Creep up on the thickness
by raising the blade a bit at a time
and then checking the results
against the mortise. Aim for a
slightly fat fit at the saw so that
you can trim to a precise thickness
afterward using a shoulder plane.
Next, saw the tenon edges.
Make sure to cut them slightly
shy as shown, which saves you
the trouble of having to round
the tenon edges or square the
mortise ends. It also allows some
adjustment for flushing the aprons
to the top ends of the legs.
All that’s left to complete your
mortise-and-tenon joints is to fine-
tune the tenon thickness, using a
rabbet block plane (as shown) or
a shoulder plane. Take just a few
swipes, then test the fit. Repeat as
necessary until the tenon inserts with
slight to moderate hand pressure.
You should be able to pick the leg up
by the apron without the joint being
so tight that you have to grunt and
contort your face to seat it. Glue can
quickly swell a too-tight joint and
make assembly a sweaty nightmare.
Don’t worry if you overcompensate
and plane the tenon too thin, as you
can always build it back up with
veneer to take another stab at it.
Cheeks first. Set up the cut using scrap and a stack dado.
Register the length of the tenon against a fence-backed spacer
block, saw one cheek, then flip the piece to saw the other.
Edges next. After sawing all the tenon cheeks, raise the dado
head to cut the tenon edges, again registering the piece against
the fence spacer before feeding the work across the blade.
Slightly shy. After sawing the edges, the tenon width should
extend only across the flat faces of the mortise, not into the
rounded ends. This does not compromise the joint strength.
Final fitting. Registering an apron piece against a
bench hook, use a finely set rabbet block plane (shown)
or shoulder plane to trim the tenon to final thickness.
40
Fair curves for a shapely apronTo shape the long aprons, begin by
laying out the curve using a batten.
(If the apron includes curved grain,
orient the batten to complement
it, as shown.) Note that the curve
begins 2" in from each tenon
shoulder. Trace a nice, bold line
that you won’t lose at the bandsaw,
and cut just outside it. Next, fair
and smooth the curve. Don’t give
in to a temptation to do this with a
spindle sander or the nose of a belt
sander, as it’s likely to go badly using
a small drum on such a large curve.
Fairing a curve like this is best
done with a cutting tool like a
spokeshave. A block plane will also
work as long as you skew it. Whatever
tool you use, fair back some of the
wood where the ends of the curve
meet the lats. he goal is to create
an easy sloping transition. Follow
up by smoothing the entire bottom
edge of the apron with sandpaper.
Finally, rout the button mortises,
which will provide purchase
for the button hold-downs that
secure the top to the table base.
Tapers shape the legsI taper just the inside faces of the
legs, starting at 7" down from the top,
as shown in the drawing on p. 36.
You could lay out the tapers, cut
them at the bandsaw, and then clean
up to your cut lines with a jointer
or hand plane. However, a table
saw tapering jig does the job much
more eiciently and consistently.
Plus, when using a jig, you need
only lay out the tapers on one leg,
which you’ll then use to set up
the fence and stop on the jig.
A jig for the job. A table saw tapering jig provides the best way to shape the legs. This
version (see onlineExtras) was designed by woodworker and teacher Steve Latta.
Spring the curve. To lay out the apron
curve, trace against a thin wooden batten
held in place with a finishing nail at the
center and a 2"-wide block at each end to
automatically locate the curve’s ends.
Just plane fair. A block plane does a
great job of fairing the apron curve, as
long as you skew it, which effectively
shortens the sole enough for the
blade to contact the concave edge.
Mortising for
buttons. A router
outfitted with an edge
guide and 1⁄2"-dia.
plunge bit makes
easy work of cutting
the button mortises.
Here, a simple holding
jig secures the
workpieces for the job.
Batten
Oct/Nov 2018 | woodcraftmagazine.com 41
Glue up in stagesIn preparation for glue-up, do a dry
clamping to ensure the joints close well
and the top edges of the aprons align
with the tops of the legs. his is also a
good time to prepare your clamping
cauls and rehearse your procedures
before reaching for the glue.
When you’re ready to glue up, begin
with a side assembly. Apply glue to
the long mortise walls, and then to
the tenon cheeks. hese face-grain
to face-grain contact surfaces are
all that matter. Deinitely avoid the
tenon shoulders to prevent a big
squeezeout mess. Immediately pull
the joints together with clamps, and
check that the top edges of the apron
align with the tops of the legs. If the
apron sits lower than the leg, work
quickly to correct the alignment as
shown below. If the leg sits lower,
place a caul atop the uprighted
apron and leg, and spread a pipe
clamp’s jaws between the caul and
the underside of your workbench
to pull the parts into alignment.
Scrutinize for glue squeezeout
and remove it immediately. I scrub
it away with a tooth brush and
clean water. Aterward, I feather the
water outward to randomize any
remaining traces. When you have
completed both end assemblies,
wait about an hour for the glue to
set, then clamp both assemblies
to the long aprons, and check the
base for square by comparing
its diagonal measurements.
Then connect the aprons.
After the glue sets on the
end assemblies, glue them
to the aprons. Use strong
clamps, again making sure to
align the aprons’ top edges
with the tops of the legs
before the glue tacks up.
Side assemblies first.
Taping 3⁄4"-wide cauls to the
legs in line with the apron
directs the clamping pressure
across the apron to prevent
the legs from cocking. If the
apron sits shy of the top of
the leg, invert the assembly,
and tap or clamp it into
alignment as shown here.
3⁄4"-wide caul
42
Tips to make the top
Finishing up
he table top is really the star of the
show, so spend some time selecting
just the right board. You want some
4/4 stock that excites you, but that
is also lat enough to yield ⅞" in
thickness ater milling, which is no
small feat. For a visually cohesive
laminated top, cut all the pieces from
the same board. Ideally, you want
straight grained sections on edges to
obscure the seams. Remove any end
checks, then cut the pieces at least an
inch over their inished length. When
you’re happy with the composition of
your boards, mark their orientation
with a triangle. I run each mating
edge over the jointer to ensure perfect
closure. Once you conirm everything
pulls tight, glue up the panel.
Ater glue-up, level and smooth
the top with hand planes, and then
scrape and sand it. Saw it to inal
dimensions, rout a ¼"-radius
roundover on all edges, and
inish-sand. (See page 30 for tips
on making great table tops.)
All that’s let is to apply a inish and attach the top.
he usual approach we teach begins by slathering on
boiled linseed oil, letting it soak in, and then wiping
of the excess, which really “pops” the wood’s natural
color and igure. Ater the oil dries for at least 5 days,
apply four or ive coats of a wipe-on poly, sanding
between coats with 400 grit sandpaper and rubbing
with 0000 steel wool. Ater the inal coat is applied,
allow the piece to cure for a week, then do a inal
rub-out with 0000 steel wool lubricated with mineral
oil. Alternatively, if you make your base of oak or ash,
consider treating it with a lame inish, as shown at right.
he last step is to make the wooden buttons (See
onlineExtras), and use them to attach the top. Make sure
to set them back ⅛" or so from the long aprons to allow
for seasonal expansion. Okay, class over. Nice work! ■
Composition for triangle. When laminating a top from multiple
boards, note your final composition with a triangle to ensure
that you glue the boards back up in the same order.
Crosscutting to
length. After ripping
an assembled top
to final width, cut
it to length using
a crosscut sled.
Black base, tawny top. The flame finish (see p. 54) on this red oak
base beautifully complements the natural tones of the figured oak top.
Oct/Nov 2018 | woodcraftmagazine.com 43
Tune up your woodworking skills with a project
that will bring enjoyment for years to come.By Doug Stowe
Cigar box guitars have been
around for a long time; the
earliest versions date back to
the Civil War era. Two centuries
haven’t diminished the appeal of
this homespun instrument. hough
a box guitar won’t have the same
acoustic properties as a standard
version, it provides just the same
playability, in a compact, rugged
package. Building your own ver-
sion is a great way to get started
as a luthier.
I began making box guitars with
high school students in my shop
class several years ago. Rather than
depend on a ready supply of cigar
boxes for these guitars, I decided to
put my box-making skills to good
use. Although the box I’m build-
ing here is a basic rectangle with
inger-joint corners, other joinery
details and box shapes are also pos-
sible. he goal remains the same:
Have as much fun making your
guitar as you’ll have playing it.
Let’s get started!
Build a BOX
BRIDGE BRACE1⁄2 × 1⁄2 × 6"
TOP3⁄16 × 9 × 11"
BRIDGE (See p. 53)
SADDLE (See p. 53)
STEEL TAILPIECE(See p. 52)
Decorative circle 23⁄4"-dia.
BACK3⁄16 × 9 × 11"
END3⁄8 × 25⁄8 × 9"
#6 × 1⁄2" sheetmetal screw
#10 × 3" F.H. screwWasher
BACKING STRIP1⁄8 × 3⁄4 × 11"
Soundhole2"-dia.
44
Order of Work• Build the box frame.
• Make and attach the back to the box.
• Make the neck.
• Cut fret slots and install the frets.
• Attach the neck to the box.
• Install tuning machines, then make and
install the bridge, nut, and tailpiece.
• String up and play.
GUITARWell-made parts and luthier supplies make wood sound goodYou don’t have to be a guitar player to make a ine box
guitar, but it helps to familiarize yourself with the key
parts of this stringed instrument. Clear, straight-grained
spruce and cedar are good woods to use for the top of the
guitar. I like to use hardwood for the remaining parts.
Fret wire
Fret scale
Fret saw
Depth guide
Micro files
Gauged nut slotting file
1⁄8" dogleg chisel
Guitar string Tuning machines
FINGERBOARD
FRET
NECK13⁄4 × 21⁄2 × 24"
BLOCKING3⁄4 × 21⁄2 × 7"
Finger-joint corners(See p. 46)
SIDE3⁄8 × 25⁄8 × 11"
NUT
HEADSTOCK(See p. 51)
Tuning machine
Special tools and materials. Basic
woodworking tools will handle many
aspects of box guitar construction.
But you’ll also need some special
items, which are available from
dealers who specialize in luthier
supplies (see Buyer’s Guide, p. 68).
Opening photo: Bobby Schehl; Tools photo: Larry Hamel-Lambert; Illustrations: John Hartman Oct/Nov 2018 | woodcraftmagazine.com 45
Finger joints are strong and attractive—a ine choice for box guitars and other
woodworking projects. While some box joint jigs are designed to cut ingers and
sockets of diferent sizes, mine is set up for a single size: ⅜". Make sure to test
your jig on some scrap stock before you use it to make the guitar’s box frame.
Pins first, then sockets. Two facing sides will begin with pins. Butt
a side against the key, rout the first pin, then straddle the key to rout
remaining pins. To rout a socket side, butt the side against a completed
pin to set up the first socket cut, then complete the straddle-and-cut
sequence (left). When assembling the box frame, take time to spread glue
thoroughly on the joints (above), and make sure the frame is square.
How to make & use the Jig• Rout runner dadoes in a single
workpiece from which the base
and sled can be cut. Then rout
the dado for the fence.
• Cut the dadoed workpiece apart to
create the base and sled. Then cut
and install the hardwood runners.
• Drill a 11⁄2"-dia. hole in the base to
provide clearance for the router collet,
then screw the router base to the
underside of the jig’s base. Outfit the
router with a 3⁄8" straight upcut bit.
• By raising the bit in 1⁄8" increments,
and sliding the sled on the base,
rout a 1-3"-long slot in the sled.
• Screw a stop block to the base
to stop the sled when the bit
will be housed in the fence.
• Position the fence in its dado so
you can rout a slot for the key. Then
slide the fence over so the key is 3⁄8" from the slot in the sled.
• Clamp the jig to the edge of a
workbench, and cut some test
joints. If necessary, fine-tune the
position of the fence (and key)
until you get finger joints that fit
snugly without being forced.
• Screw the fence to the sled
when the fit is right.
Build a box frame with finger joints
Stop block
BASE3⁄4 × 121⁄2 × 16"
Screw fence to sled after fine-tuning fence position.
Clamp base to workbench.
Fasten router base to underside of jig base.
RUNNER3⁄4 × 3⁄4"
STOP BLOCK
55⁄8"
4"
SLED3⁄4 × 121⁄2 × 8"
11⁄2"
Collet clearance hole11⁄2"-dia.
Slot3⁄8" W.KEY
3⁄8" W.
Pin side
Socket side
21⁄4"
Finger Joint Jig
FENCE3⁄4 × 3⁄4 × 121⁄2"
Dado3⁄4 × 3⁄8"
46
Once the box frame is together and the exterior has
been sanded smooth, it’s time to add two more parts.
Gluing solid hardwood blocking to the box interior
where the neck will be attached ensures a strong neck
connection. he book-matched back is a traditional
luthier’s detail that adds beauty to the back of the guitar.
Now add blocking and a book-matched back
A book-matched back. After planing boards to a thickness
of around 3⁄16", glue up the back, orienting the boards to create
the best book-match. When the glue dries, plane the back
slightly thinner, and glue a backing strip over the seam.
Blocking for the neck. Glue a 3⁄4"-thick maple
block to the inside of the box where the neck
will attach. The top edge of your blocking board
should be flush with the top edge of the box.
Too many clamps? Using fewer clamps and
some clamping cauls to distribute pressure will
work just as well here. Note the 1⁄8"-thick, 3⁄4"-
wide backing strip glued in place over the book-
match joint before gluing the back to the sides.
Flush-trim the back. After the glue dries,
I use a flush-trim bit in the router table
to trim the bottom flush with the sides.
Project photos: Doug Stowe
Blocking
Clamp pad
Backing strip
Blocking
Oct/Nov 2018 | woodcraftmagazine.com 47
A blank with blocking. Start with a dead flat neck blank 7⁄8" thick, 23⁄4" wide, and 25" long. Then thicken each end
of the neck blank by gluing blocking in place as shown.
Shape, then smooth. I use a rasp to refine the shape of the
neck. Fair the neck’s curve by eye, but also test your progress
by feel. When shaping is done, smooth by sanding to 220-grit.
Rough out the shape. After drawing the tapered
layout on the neck blank, cut the neck to rough
size. Stay slightly outside the lines.
he neck starts out as a straight length of hard maple
that gets blocking glued to each end. Building up the
thickness at each end gives a stronger connection where
the neck joins the box, and allows the peg head to be
angled back, keeping the strings in tension against the nut.
he drawings below provide the details for making the
neck blank and then cutting and shaping it to inal size.
Before cutting any tapers on the bandsaw, make sure that
the end of the neck (which joins the box) is cut perfectly
square. Once the rough shape of the neck is cut, take your
time with inal shaping and smoothing, because you’ll
want this part of the guitar to be comfortable to hold.
The neck needs a graceful shape...
Neck Details
21⁄2"
21⁄2" 13⁄4"
113⁄16"
3⁄8" R.
24"
141⁄2"
41⁄2"
5"
15°
48
Saw the slots. Clamp a guide block on each fret’s layout
line to keep the saw vertical as you cut. Adjust the fret saw’s
depth gauge to match the fret wire's barbed flange.
Accurate layout. With an inexpensive fret template,
you can precisely lay out frets without measuring.
Align the template over a centerline on the neck, then
mark the nut and fret slots with a sharp pencil.
Seat, snip, and file. Allow each fret to extend
beyond the neck sides when you install it, seat the
fret with a hardwood block, to avoid damaging it
with a hammer. Then snip the fret just proud of the
sides with wire snips. Use a fine-cutting metal file
to get fret ends flush with neck sides, then gently
round the ends over so they're smooth to the touch.
Connect the neck. Lay out a triangular pattern for drilling pilot holes
in the neck and the box for three #10 × 3" screws. Layout and drill
each set of holes so the neck will be centered on the box, with the
fingerboard 1⁄4" above the box side where it’s attached. With the
neck clamped in a vise, I place a washer beneath each screw head,
and use a ratchet-type driver to torque down the connection.
Fret wire has a T-shaped proile with tiny barbs that keep
frets locked in kerfs made with a fret saw. Once you’ve
inished installing the frets, take extra care in screwing the
neck to the box. Clamp the neck in a vise as shown below.
...and precisely spaced frets.
Center point
Fret slotsFret dot locations
Wide slot for nutGuide block
Oct/Nov 2018 | woodcraftmagazine.com 49
Good sound depends on good wood. Luthiers oten use
Western cedar for guitar tops, and I found some at my
local lumber yard—with enough thickness to resaw, glue
up, and plane to make a good top. Look for clear stock
with closely spaced growth rings; this tells you that the
wood has taken longer to grow and will give a more vibrant
tone. Plan on making a top piece ¼"-⅜" larger than the
outside dimensions of your box, so it can be lush-trimmed
ater installation. Ater gluing up two book-matched
boards, plane and sand the top to about ⅛" thick.
Good progress! Now let’s work on the top...
Make the sound hole with a circle cutter. In addition to
using my hole cutter to make the 2"-dia. sound hole, I also
set a larger diameter to make a decorative shallow circle, as
shown here. To avoid tearout, drill halfway through, then flip
your top and complete the cut from the opposite side.
Glue a brace beneath the bridge. The underside of
the top needs some reinforcement beneath the planned
location of the bridge. Glue a 1⁄2" square × 6" long
brace in place as shown. Make sure to protect the soft
cedar with clamping pads on the top’s show face.
Glue the top to the box.
Spread glue on the top
edges of the box and
press the top in place.
Instead of using several
clamping blocks, I simply
placed a single piece
of 1⁄8" plywood over
the top before putting
clamps in place. Trim
the edges flush at the
router table as before.
Decorative circle
Bridge brace
Underside of top
Clamp pad
50
Tuning machines vary in
size and design, so it’s best
to have yours in hand before
you begin building the guitar
neck. his will enable you
to make sure that holes for
pegs are sized and spaced
correctly. Select a drill bit that
matches your peg diameter.
Make the nut from a hard,
durable wood like persimmon
(which I used here) or ebony.
Synthetic ivory (available
from luthier suppliers)
is also a good choice.
...and install the tuning machines and nut.
Perfect holes for peg heads. To avoid tearout,
I mark the hole centers and drill them out with
a 1⁄8"-dia. bit. Then I drill in from both sides with
a full-size bit, guided by the smaller holes.
Aim for a firm fit. I made the nut from persimmon, the only North
American member of the ebony family. Cut the nut a hair oversize,
then sand it for a tight fit, so it can be adjusted or replaced.
Chisel out the nut slot. The nut’s location is marked when
laying out the frets. The width and depth of the nut slot is
defined by a pair of parallel saw kerfs. I use a 1⁄8" chisel to
remove the waste and create a flat recess for the nut.
Tiny screws for tuning machines. Drill pilot holes
that extend the full length of the screw shank. This will
prevent stripping or breaking these tiny fasteners.
Full-Sized Headstock Pattern
13⁄16"
41⁄8"
21⁄2"
7⁄16"
Oct/Nov 2018 | woodcraftmagazine.com 51
Before tackling these inal construction steps, treat your
guitar to some inish. My preference is to apply several
coats of wiping varnish. Once the inish is dry, it’s time to
focus on how to anchor the strings to the base of the guitar,
support them an appropriate distance from the nut, and
put them at a uniform height above the neck (action). As
you complete this inal work, keep in mind that the action
is important. Too high, and it’s diicult to push strings
down against the ingerboard. Too low, and the strings
will buzz against the frets. Since the nut and the saddle
are responsible for holding the strings, action adjustments
are made by raising or lowering these two parts. ■
Get set for strings, then start to play!
Punch, then drill. Follow the layout to mark
hole centers, then use a metal punch to make
a recess that will guide your drill bit. After
drilling holes, you can personalize your guitar
by using metal stamps on the tailpiece.
Install the tailpiece. Use a straightedge to align the tailpiece
with the fingerboard. Painter’s masking tape can mark the
location as you drill pilot holes for three installation screws. Drive
these through the tailpiece holes and into the box bottom.
Use a vise to bend the metal. Put a near-90°
angle where the tailpiece folds from the end to the
front of the guitar. Then make an additional slight
bend along the string holes to provide clearance
underneath for the ball ends of the strings to fit.
Full-Sized Tailpiece Pattern
33⁄8"
21⁄8"
21⁄2"
25⁄8"
3⁄8"
11⁄4"
Cut the tailpiece from galvanized sheet metal, then use a fine-cutting metal file to smooth all cut edges. All holes are 1⁄8" dia.
Mounting hole
Bending lines
String hole
52
Finish off the nut. Space string slots 1⁄4" on center. Use fine rasps
to file each slot, making wider slots for the thicker strings. Don’t
glue the nut in its slot, so it can be replaced or adjusted later.
Make the bridge. The bridge has coved ends and a
slotted center that holds a separate but snug-fitting 1⁄8"-
thick hardwood saddle containing the string slots. File these
on the layout shown above, again using fine rasps.
Glue down the bridge. Proper tone depends on the correct
distance between the saddle and the nut—243⁄4" for the
template I’m using. String up the guitar, position the bridge
as shown, and mark its outline with tape. Then loosen the
strings and scuff the top where the bridge will fit using 220-
grit sandpaper. Spread glue on the underside of the bridge,
position it on the top, and tighten the strings to keep it in place
as the glue dries. Great job! Now you can start strummin’.
Full-Sized Bridge and Saddle Details
43⁄8"
3⁄8" 1"
Replaceable saddle1⁄8 × 3⁄8 × 31⁄2"
Bridge is glued to top.
Check out Doug’s book: The Box Maker’s Guitar Book, available at woodcraft.com.
Oct/Nov 2018 | woodcraftmagazine.com 53
An unlikely alliance of fire and wood
creates a strikingly beautiful surface.
The Japanese call it shou sugi ban. It translates to “burned cypress
plank,” and is a traditional approach to treating home siding in
Japan. Charring the surface of the wood creates a beautiful black
inish that protects not only against rot, but also insects, who evidently
hate the taste. It may seem counterintuitive, but this shallow, quick
burning of the wood makes it ire resistant as well.
I’ve found that shou sugi ban is a great, tactile inish for interior work
as well, and that it imparts a truly striking color and texture to a two-tone
furniture piece like the table on page 36. Although cedar and pine are
the traditional materials of choice for outdoor woods, I ind that open
grained, ring porous hardwoods like oak and ash lend a more reined
look in their textures. Shou sugi ban is not a diicult skill to learn, very
little equipment is required, and the style is currently very hot.
By Robert Spiece
onlineEXTRAVisit woodcraftmagazine.com to
see a short video of the author
succumbing to his pyromania.
Safety AlertTo be absolutely fire-safe, you could
burn outside on a concrete slab.
However, I prefer to work inside in an
area cleaned of sawdust, shavings,
and wood scraps. If you can, begin
the process with the piece upside
down, targeting the raised section
of the inverted piece, as I did with
these table legs. For small pieces and
panels, raise the work on cinderblocks.
Of course you’ll want to keep water
and a fire extinguisher at hand just
in case. Finally, don’t work tired
or mentally impaired; you need to
stay alert when playing with fire!
FINISH
(shou sugi ban)
54
Tools and equipment For the burning, I use a portable
propane tank from the hardware
store. It’s inexpensive and provides
plenty of fuel for the job. I outit it
with an adapter on an extension hose
to allow better maneuverability and
lame control. For cleanup, choose a
brush with stif plastic bristles, which
will remove soot without scarring
the wood. To touch-up ofset areas
or recesses that are hard to burn
properly, you can employ black aniline
dye or a ine-tip black marker.
Photos: John Hamel
The right wood makes all the difference I consider red oak the perfect candidate for this inish,
although white oak and ash also take very nicely to
it. he striking appearance is as much about texture
as color. he coarse, open grain and clear delineation
between latewood and earlywood in these species make
the treatment really pop. he “cut” of the wood makes
a diference too, as seen in the photo.
Before charring, sand the work
through 180 grit. It may seem
ridiculous to spend time sanding
something that you’ll put a
lame to, but charring doesn’t
remove machine marks, and they
don’t look good burned or not.
Good cooking candidates.
Oak and ash look great charred,
brushed, and finished, regardless
of the cut of the wood.
Clean and safe. When using flame in the shop, work in a clean,
uncluttered area, and keep water and a fire extinguisher at hand
just in case. With a table like this, invert it and burn the upended
sections of the legs before righting it to finish the rest.
Plainsawn white oak
Quartersawn red oak
Plainsawn red oak
Plainsawn ash
Portable propane tank with adapter and extension hose
Mixed black aniline dye
Stiff-bristled plastic brush
Black aniline dye powder
Artist’s brush
Black fine-point marker
Oct/Nov 2018 | woodcraftmagazine.com 55
Burning creates the color
Brushing brings out the texture
With the work at the ready, adjust your torch for a
strong lame. hen, working in short, overlapping
passes, play the lame over the surface. he trick
to achieving a consistently lat, black char is to
target small areas at a time, moving along as soon
as the surface catches ire, ater which the lames
should immediately die out. If you’re getting
anywhere near the point of needing to douse
the project, work on ine-tuning your irebug
sensibilities. Linger only as long as necessary, and
avoid holding the lame too close to the work.
Go slowly over the piece, working one section or
component in turn, paying attention to the lash point
frequency as you move. You’ll ind that quartersawn
grain burns much more evenly and easily than
latsawn surfaces, so adjust your pace to suit. It can
be diicult to get a solid black burn at the juncture
of ofset joints or other recesses without overcooking
the wood, so leave them for touch-up later with
dye or a marker. Scrutinize completed surfaces and
revisit any areas that haven’t been fully blackened.
he next step is brushing,
which cleans away the
majority of the soot
while creating texture.
his is due to the fact
that early growth burns
away more readily than
the late growth. Brushing
also helps to more evenly
distribute the color. It’s
not a complicated process,
and it goes pretty quickly;
just scrub vigorously in
the direction of the grain.
Move flame in slow, short strokes up and down...
Getting the brush-off. Wherever possible, scrub in the direction of the grain, which
better reaches into the furrows of the more easily burned early-growth wood.
56
Finishing includes a bit of touch-upNow’s the time to touch up around
any ofset joints or other recesses that
you couldn’t burn properly. You may
be able to reach into these areas with a
ine-tip marker, but applying dye with
an artist’s brush is a better bet. I used
to dye the entire piece ater burning,
in order to ill in any insuiciently
charred areas. However, I’ve found that
it’s kind of cool to see a bit of the oak
color peeking through when lit with
warm sunlight. It creates a bit of subtle
warmth that the dye would remove.
Next, I suggest wiping the whole
piece with boiled linseed oil. (Be sure
to properly dispose of your oily rags, or
you may have another type of ire to deal
with.) Ater allowing the oil to cure for 5
days, I top-coat the piece with 3 or 4 coats
of a satin wipe-on polyurethane, rubbing
out with 0000 steel wool between coats. ■
Slowly move up to complete the section, repeating the short stroke movement until flaming.
...until the surface flames.
Then move to next section and repeat.
Linseed oil sealer. Before applying several top coats of
poly, I wipe on a coat of linseed oil to clean the surface of
any loose charcoal dust and to provide some nourishment
to wood that has been sapped of moisture by the flame.
Oct/Nov 2018 | woodcraftmagazine.com 57
Compact CLAMP CARTThis roll-around caddy
holds everything you need
for glue-ups and fastening.
Is it possible to simultaneously feel as if you own
too many and too few clamps? If your clamps
are piled more than a few steps away from your
assembly table, then you already know the truth
behind this woodworking paradox. When a glue-up
goes smoothly, lugging clamps from one end of the
shop to another (and cleaning them up at the end of
the job) can feel like an endless chore. When things
go south, the seconds lost searching for a few more
clamps can result in disappointment, or even disaster.
his roll-around clamp caddy will clean up your
clamp collection and may even tidy up your assembly
operations. Despite a surprisingly small footprint—
about 3½ sq. t.—the cart’s main rack can hold more than two dozen panel
or bar clamps. Spin it around, and you’ll discover two 36"-tall compart-
ments ofering shelving space for storing other assembly essentials, and my
growing Festool collection. A pair of side racks attached to one side provide
convenient storage for an arsenal of F-style, pistol-grip, and C-clamps. he
remaining side can be accessorized to accommodate all sorts of clamping
and joinery essentials, such as mallets, squares, and hardware.
he basic cart can be assembled in a weekend. Ater hanging your
clamps and stocking the shelves, you can spend a few more hours build-
ing custom hangers for your most-used tools.
Like the Mobile Assembly Cart that appeared in our April/May 2014
issue (#58), this project’s success hinges on its smaller stature. At 16 × 32
× 53", this caddy is easy to steer around a small workshop and through
doors, but it’s not well-suited for clamps longer than 60". My collection of
extra-long clamps are kept on a sturdy wall-mounted rack that appeared
in our Oct/Nov 2011 issue (#43). To download PDFs of both projects,
go to woodcratmagazine.com and click on OnlineExtras.
By Joe Hurst-Wajszczuk
58
Order of Work• Cut the sides, top, and bottom from 3⁄4" plywood.
• Rout the dadoes and grooves for
the top, bottom, and back.
• Dry-assemble the case, and then rout the dadoes
for the divider.
• Cut the divider and back panels to fit,
and then assemble the case.
• Assemble and install the clamp rack.
• Build the drawer, and accessorize your cart to suit.
Photos: Ralph Lee Anderson; Illustrations: Frank Rohrbach III
his project’s ixed case parts require
just one sheet of ¾"-thick plywood and
about a half-sheet of ½"-thick plywood.
(You can use the letover material to
make shelves and tool holders.)
Download the cutting diagram
(see OnlineEXTRAS) and have
the plywood cut to rough size
at the home center, then inish
cutting the parts in your shop.
11⁄2 sheets of plywood, 2 stair treads, and 10 dowels
BACK RAIL1 × 41⁄4 × 48"
CLEAT3⁄4 × 1 × 41⁄2"
11⁄2" F.H. screws
RUNG11⁄8-dia. × 38"
BACK1⁄2 × 31 × 361⁄2"
LONG SIDE RAIL1 × 31⁄2 × 371⁄4"
DOWELS11⁄8 × 8"
SHORT SIDE RACK1 × 31⁄2 × 291⁄4"
Side rack dowels 11⁄8-dia. × 8"Side rack holes 6" o.c.
SIDE3⁄4 × 16 × 48"
ADJUSTABLE SHELF1⁄2 × 15 × 123⁄4"
CASTER PAD1⁄2 × 31⁄2 × 33⁄4"
Lag screw1⁄4 × 1"
21⁄2" caster
BOTTOM3⁄4 × 16 × 31"
DIVIDER3⁄4 × 15 × 361⁄2"
DRAWER(See p. 62)
Dado1⁄4 × 3⁄4"
Dado1⁄4 × 3⁄4"
Groove1⁄4 × 1⁄2"
Rabbet1⁄4 × 3⁄4"
TOP3⁄4 × 16 × 31"
MALLET PAD3⁄4 × 71⁄2 × 81⁄2"
HANGER CLEAT1 ⁄2 × 51⁄2 × 51⁄2"
HANGER STRIP3⁄4 × 11⁄2 × 141⁄4"
BRACE3⁄4 × 21⁄2 × 63⁄8"
Side Detail
1613⁄16"
he adjustable shelves and
sides can be customized to suit your
storage needs, but the 1613⁄16"-wide
compartment is designed to accommodate
Festool’s Sys-AZ drawer hardware.
Oct/Nov 2018 | woodcraftmagazine.com 59
Quick Tip: Simple shelf pin insurance
A solid case, simply builthe trick to building a strong, square
case is working in a manner that
overcomes the tiny errors resulting
from nominally-dimensioned
plywood or from cutting on the wrong
side of a pencil line. Start with the
dimensions, then shit your focus on
consistency. For example, ripping all
of the outer parts of the case to width
at the same time and stack-cutting
corresponding parts to length ensures
that matching parts are the same
size, even if your measurements are
a bit of. When routing the dadoes
and rabbets for the top and bottom,
clamp the sides together, and then
rout the pair at the same time. Rather
than relying on measurements,
use scrap to set the widths of
grooves and dadoes, as shown.
To ensure that my cart would
accommodate Festool’s shelving
system, I screwed the case together,
and then, routed the dadoes for the
divider with a template and lush-
trim bit. Ater cutting the divider and
back to it, I reassembled the case,
this time using glue and screws.
Once assembled, you can remove
the clamps and continue with the
build. To make the big box easier
to move, I attached the caster pads
and casters. hen, I set the case on
its side and drilled the shelf pin
holes. he 1" o.c. hole spacing ofers
plenty of shelf-positioning options.
Dadoes done right. Routing both sides at the
same time ensures that the dadoes line up.
Once set with a spacer, Bora’s WTX router guide
makes perfectly-sized dadoes in two passes.
Groove the sides for the back. When routing the groove for the back
panel, remember to register the guide’s fence against the back edge. You
want the sides to be mirror images of each other, not an identical match.
Make a trustworthy template. To position
the divider exactly 1613⁄16" from the side to
accommodate Festool’s Sys-AZ sliding drawers,
I used a template and routed the dado with
a 1⁄2" template bit. To complete the 3⁄4"-wide
dado, I inserted a pair of spacers between the
side and template and made a second pass.
Now get rolling. Plywood
pads beef up the bottom so
that the 1"-long screws don’t
poke through. Three screws
per caster are plenty.
A shelf pin drilling template can make quick work
of drilling holes, but if you forget to flip the jig when
drilling the opposing row, the holes on one side of
your opening may not align with the other. Drawing a
reference arrow on the face of the jig can help ensure
that the jig is in the right orientation. Set the arrowed
end against the bottom (or top) and keep it pointed
in the same direction when drilling the other rows.
Use square to position guide rail.
Test piece
Top edge
Bottom edge
Spacers
Template
Reference arrow
Stops1⁄4"-long template bit
Use spacer to set guide.
1613⁄16"
1⁄2"
60
Make a sturdy rack to hold heavy clampsRather than milling the 1⅛"-thick
rails from rough-sawn stock, I
purchased sotwood stair tread
material from my home center. Ater
ripping the rails to width, I taped the
pair together, and then proceeded
with laying out the holes (see Rack
Detail). When drilling, I recommend
using a drill press or drilling guide.
If the holes aren’t perpendicular to
the rails, you will have a diicult
time assembling the rack.
Even though no glue is involved,
itting eight 1⅛"-diameter rods into
1⅛"-diameter holes is a little tricky.
If a rod refuses to line up, or sticks, it
will stop the process in mid-assembly.
Ater tapping all of the rods into one
rail, I used clamps, as shown, to hold
the second rail in place, and then
to squeeze the assembly together.
Before attaching the rack to the
cart, round over any sharp edges with
a ¼" roundover bit. hen, screw the
cleats to the inside faces of the back
rails. Next, set the rack in place, and
screw the rails to the sides. Ater
checking the rack’s angle on both
sides, attach the braces where shown.
Paired to perfection.
Drilling the holes
through both rails at
once ensures that
the holes line up. To
avoid blowout, set
the drilling depth so
that the Forstner’s tip
just breaks through
the bottom rail. Flip
the rails and finish
drilling the holes.
Under pressure. Fitting and installing the rods onto the rails requires
a few extra hands. Start by applying light pressure when inserting the
rungs into the opposite rail. Then, gradually squeeze the rail onto the
rods until the distance between the rails matches the cart’s width.
11⁄2"
21⁄2"
6"
Slide rack onto cart until rung touches side.
Brace rests against back edge of case side.
Larger opening for clamps with extra-large heads.Position this end of
the clamp on the end of the dowel.
9"
2"
Packing tape
100°
80°
Rack Detail
Oct/Nov 2018 | woodcraftmagazine.com 61
onlineEXTRAS• Clamp Cart Cutting Diagram
• PLAN Mobile Assembly Cart
PLAN Wall-Mounted Clamp Rack
• Bora WTX Router Guide Review
Assemble and install the drawer, then finish the cartI made the drawer from
½"-thick plywood for
sturdiness and because
I had material let ater
making the case back. Ater
ripping the drawer front,
back and sides to width, I
routed the grooves for the
bottom where shown in
the Drawer Detail. Next, I
cut the sides to length and
rabbetted the ends. Before
cutting the front and back
to length, verify the width
of the opening. When using
full-extension slides, the
drawer’s width should be
1" less than the opening.
To assemble the box,
I used glue and staples.
Driving the staples in
from the front and back
rather than the sides
ofers plenty of holding
power and conceals the
utility-grade fasteners.
To install the drawer, irst
mount the slides 6" down
from the top’s lower face.
Next, attach both slides
to the drawer’s sides with
two screws apiece. Remove
the drawer from the case
and drive the remaining
screws. Finally, re-install
the drawer and attach
the false front and pull.
Your cart is almost ready
to work. Attach the side
racks to the case (see the
Side Detail, p. 59), and
load up your rack with
clamps. Install shelves
and tool holders to suit.
Note: If you ind that your
cart seems tipsy, move a
few clamps to the side racks
to redistribute the weight
and stock the shelves. ■
Slide installation made simple. Kreg’s slide
jig holds the hardware perpendicular to the
front edge of the case. Pointing the guides in
the opposite direction supports the drawer,
enabling you to screw the slides to the sides.
1⁄4" roundover on front edges only
FALSE FRONT1⁄2 × 67 ⁄8 × 185 ⁄16"(cut to fit)
FRONT1⁄2 × 51⁄2 × 1513 ⁄16"
1⁄2"
SIDE1⁄2 × 51⁄2 × 141⁄2"
Groove1⁄4 × 1⁄2"
Rabbet1⁄4 × 1⁄2"
BOTTOM1⁄2 × 1513⁄16 × 141⁄2"
BACK1⁄2 × 141⁄2 × 1513 ⁄16"
1⁄2" narrow crown staple
7⁄8" Washer head screw
Double-faced tape
14" full-extension drawer slide
53⁄4" stainless steel T-bar pull
Drawer Detail
62
The Market
Advertise in The MarketContact Vic Lombard
phone
(304) 865-5262 email
64
It’s a joy to use a chisel with a razor-sharp edge, and a
tragedy when a perfect edge gets ruined by an accidental
drop or ding. WoodRiver chisel guards provide cheap
insurance against damage. For less than ten bucks, you
get a set of ten guards that will it chisels from ⅛" to 1¼".
hese lexible silicone guards will it and tenaciously
grip a range of diferent chisel shapes, unlike hard
plastic chisel guards. If you hate regrinding chisels as
much as I do, you’ll appreciate these top-notch tips.
—Tim Snyder
Chisel and saw photos: Larry Hamel-Lambert; Forearm Forklift photos: Doug Loyer
Great Gear
Cheap and easy edge protection
WoodRiver Silicone Chisel Guards 10pcs
#161193, $9.99
Defying gravityMoving heavy machinery and furniture takes a toll on more than
just your back. It can damage loors, walls, ingers, and toes. Forearm
Forklit Liting Straps won’t bring back your 20-year-old physique, but
these 3"-wide nylon straps can help you move heavy objects without
damaging yourself or your surroundings. To relocate a chunk of cast-
iron or a china cabinet, slip the straps under the object, then slip your
arms into the loops and lit. Transferring the weight from your ingertips
to your forearms reduces strain while increasing your control over the
load. hese straps do a good job of keeping me out of my chiropractor’s
oice. I keep a pair in my shop and second pair in my truck.
—Joe Hurst-Wajszczuk
Forearm Forklift Lifting Straps
#150708, $20.99
A little saw with big benefits Genbaya Folding Blade
Woodworking Saw No. 0570
#159594, $22.00
I was looking for a small folding saw to it in my tool belt —
something compact but capable of trimming shims, cutting
boards to rough length, and handling other unexpected
sawing assignments that come up during remodeling
projects. he Genbaya folding saw excels at these tasks.
he 5"-long, 14 tpi, Japanese-style “woodworking” blade
that comes with this saw will make smooth, accurate
cuts in any kind of wood. But if you want to expand your
cutting capabilities, the saw accepts seven diferent blades,
including keyhole, MDF, and camper/gardening versions.
he blade locks in the open position, and the plastic
handle has proved to be both sturdy and comfortable. No
wonder this pocket-size saw has become my favorite. ■
—Tim Snyder
Items above available at Woodcraft stores, at woodcraft.com, or by calling (800) 225-1153, unless otherwise noted. Prices subject to change without notice.See the Buyer’s Guide on page 68 for more information.
66
Oct/Nov 2018 | woodcraftmagazine.com 67
Hot New Tools (p. 14)1. Bessey GearKlamp ...........................................................Coming soon to woodcraft.com
2. Jet Bandsaw JWBS14-SFX ...........................Coming soon to woodcraft.com, $1,099.99
Score Big with a Football Cutting Board (p. 26)1. Forrest 10" Dado King Set .................................................................#420747, $374.99
2. Wagner Heat Gun .............................................................................Lowes.com, $19.97
3. Freud Roundover Bit, 1⁄2" SH, 1⁄4" D, 1" CL ............................................#815157, $35.99
Teaching Table (p. 36)1. #92 Medium Shoulder Plane ............................................................ #154032, $149.99
2. Oil-free Steel Wool 0000 225g Roll .....................................................#162190, $12.99
3. Boiled Linseed Oil, Quart ........................................................................#85050$14.50
Build a Box Guitar (p. 44)1. Medium Fret Wire, 2 Foot ......................................................................................$4.21
2. Depth stop for Fret Saw .........................................................................................$8.49
3. Fret saw ..............................................................................................................$48.63
4. Economy Open-gear Tuning Machines, White Knobs, 3 Left/3 Right ....................$14.90
5. Gauged Nut Slotting File, .042" ...........................................................................$15.00
6. Micro Chisel Set of 4 ...........................................................................................$51.45
7. D’Addario Phosphor Bronze Wound Acoustic Guitar Strings ....................................$6.99
8. Needle Files, Set of 5 ..........................................................................................$18.35
(Above items available from at stewmac.com.)
9. Acrylic fretting Scale Template .........................................................cbgitty.com, $12.49
10. Black Open-gear Guitar Tuners/Machine Heads, 6pc., 3 Left/3 Right .... cbgitty.com,$9.29
11. Nicholson Cabinet rasp, 2nd cut (#49) ................................................. #06B01, $57.50
12. General Tools Large Circle Cutter ......................................................... #16N41, $32.99
13. Whiteside Flush-Trim, 1⁄4" SH, 1⁄2" D, 1" CL .............................................#24A71, $16.94
14. SE 36-piece Number and Letter Marking Punch Set .......................amazon.com, $16.20
Items above available at Woodcraft stores, at woodcraft.com, or by calling (800) 225-1153, unless otherwise noted. Prices subject to change without notice.
Buyer’s Guide
Flame Finish (p. 54)1. Bernzomatic TS3500KC Multi-Use Torch Kit ............................. homedepot.com, $29.97
2. Bernzomatic WH0159 Universal Torch Extension Hose ...............homedepot.com, $15.97
3. Boiled Linseed Oil, Quart ...................................................................... #85050, $14.50
4. Oil-free Steel Wool 0000 225g Roll .....................................................#162190, $12.99
5. Homestead Transfast Dye Powder, Accent Color, Black ....................... #123836, $12.50
Compact Clamp Cart (p. 58)1. Bora WTX Router Guide .....................................................................#542005, $49.99
2. Bora WTX 36"-Wide Track Modular Clamp Edge .................................#543036, $47.99
3. Freud Upcut Spiral Bit, 1⁄2" SH, 1⁄2" D, 11⁄4" CL ...................................... #828780, $67.47
4. Whiteside Bearing Dado Template Bit, 1⁄4" SH, 1⁄2" D, 1⁄4" CL ................. #814645, $21.56
5. WoodRiver 21⁄2" Caster, Swivel Plate (4 needed) .................................. #152836, $13.50
6. WoodRiver 15-hole 1" Spacing Shelf Pin Jig .................................... #150721W, $23.99
7. WoodRiver 1⁄4" Drill Bit for Shelf Pin Jig ............................................ #150722W, $18.99
8. Freud Precision Shear Forstner Bit, 11⁄8" dia. ....................................... #832878, $16.99
9. Hafele Shelf Supports, Bracket Style, Bronze, 1⁄4" (25 pack) ..................... #27I16, $5.29
10. Kreg Drawer Slide Jig ......................................................................... #162006, $24.99
11. Kreg 3" Classic Face Clamp (2 needed) ..............................................#149086, $22.99
12. Highpoint Full Extension Side Mount Drawer Slides, 14" .......................#160241, $14.99
13. Vanitek Magnetic Tool Holder, 12" (2 bars) .....................................amazon.com, $12.99
Great Gear (p. 66)1. WoodRiver Silicone Chisel Guards, 10 pc .............................................#161193, $9.990
2. Genbaya Folding Blade Woodworking Saw, No. 0570.......................... #159594, $22.00
3. Forearm Forklift Lifting Straps ............................................................ #150708, $20.99
68
Adhesives
Satellite City .................... caglue.com ...............................16
Bits, Blades, and Cutters
Forrest Mfg. ..................... forrestblades.com .....................19
Freud .............................. woodcraft.com/Freud ............... IFC
PS Wood ......................... pswood.com .............................64
Whiteside Machine ........... whitesiderouterbits.com.............63
Clamps & Hold-Downs
Bessey ............................ besseytools.com .......................18
Blokkz ............................. blokkz.com ...............................64
Woodpeckers ................... woodpeckers.com .....................23
CNC
Digital Wood Carver.......... digitalwoodcarver.com ...............64
Next Wave Automation...... nextwaveautomation.com ..........25
Dust Collection
Oneida ............................ oneida-air.com ................. 22 & 70
Finishing
Howard ........................... howardproducts.com .................16
Rust-Oleum ..................... woodcraft.com ..........................69
Hand Tools
Kutzall ............................. kutzall.com ...............................11
Thomas Flinn & Co. .......... flinn-garlick-saws.co.uk ............68
WoodRiver ....................... woodcraft.com ..........................13
Hardware
National Hardware ........... natman.com .............................64
Moisture Meters
Lignomat ......................... lignomat.com ............................20
Wagner Meters ................ wagnermeters.com ...................14
Power Tools
Earlex .............................. earlex.com................................19
King Arthur’s Tools ........... katools.com ..............................25
Laguna Tools ................... lagunatools.com............. 24 & OBC
Rikon .............................. rikontools.com .........................IBC
Triton .............................. tritontools.com ............................1
School/Instruction
The American Woodshop .. wbgu.org/americanwoodshop ....19
CT Valley School of WW .... schoolofwoodworking.com .........68
Woodcraft Magazine ........ woodcraftmagazine.com ....64 & 67
Turning Supplies
Berea Hardwoods............. woodcraft.com ..........................67
Carter.............................. carterproducts.com ...................17
Nova ............................... woodcraft.com ............................5
Robert Sorby .................... robert-sorby.co.uk .....................10
Wood & Veneers
Cook Woods .................... cookwoods.com ........................15
Northwest Bamboo........... nwbamboo.com ........................64
Woodworking Supplies
Harbor Freight.................. harborfreight.com .....................21
Lee Valley ........................ leevalley.com ............................65
Perfection Chain Products ... perfectionchain.com ..................15
Tanos .............................. woodcraft.com ..........................20
Woodcraft Franchise ........ woodcraftfranchise.com ..............7
Woodcraft Supply ............. woodcraft.com ..........................71
Ad Index
Oct/Nov 2018 | woodcraftmagazine.com 69
Expert Answers
Proper angles for dovetails
Professional woodworker Chris Hedges replies:
Dovetail angles are expressed in two ways: as ratios
and degrees. 1:8 roughly translates to 70 and 1:6
translates roughly as 90. hese days, we oten hear
that 90 is recommended for sotwoods, while 70
should be used for hardwoods. he fact that router
bits and dovetail gauges are made in these angles
reinforces the notion that they are the preferred
angles to use. But if you happen to study antique
furniture, you’re likely to see dovetail angles that
range from 7° to 140 (1:4 ratio). Woodworkers
who came before us chose their dovetail angles for
the sake of appearance, I suspect. his notion is
reinforced by research done at the Forest Products
Laboratory. FPL testing on dovetail joints made at
diferent angles between 7.5° and 17.5° showed no
diference in joint strength. My suggestion: Invest
in a good-quality bevel gauge that allows you to
choose your own dovetail angles, and train your eye
to be your guide in deciding what angles to cut. ■
I’ve started to work on laying out and cutting
dovetail joints by hand, and I’m confused about the
proper angle to use for dovetail joinery. What are the
most common angles, and what are the factors that
determine what angle to choose?
—Carl Minnick, via email
We’ll do our best to find the expert and provide the answer.
Have a tough woodworking question?
Mail your query to: EXPERT ANSWERSWoodcraft MagazineP.O. Box 7020 Parkersburg, WV 26102-7020
Email us at: [email protected] Please enter “EXPERT ANSWERS” in the subject line.
Ask an EXPERT
70
Top photo: Doug Loyer
D ave and I had just sat down
for our usual bagels, cofee,
and conversation at the local
diner. He was looking pretty
good, considering his recent
treatment for a tenacious form
of brain cancer detected a few
months earlier. his tough
old ex-Navy pilot didn’t talk
about it much though, and I
sometimes wondered if his illness
shook me more than him.
He reached for his cofee
and said, “I need a favor. You’re
a woodworker; I want you to
make me a pine box.” hen he
handed me a one-page plan for
the kind of “toe-pincher” style
casket you see in the Westerns.
My jaw probably dropped
when I realized what he was
asking, but I wasn’t going to turn
down this friend of 25 years. I
assured him I’d take care of it,
but told him I didn’t think he’d
really need it for another 10 years.
We inished our breakfast chat,
shook hands, and—wanting to
honor him with more than a toe-
pincher—I was of to investigate
the crat of casket-making.
Turns out it’s not easy to ind
good information on the subject.
I bought a book on the topic,
but found it less than helpful.
An internet search led me to a
site where
I purchased
a plan that was
clearly intended for someone
with better woodworking
chops than mine. he sparse
instructions were not for the
faint of heart, leaving a lot to the
imagination, particularly when
it came to things like cutting the
35.25° and 30.33° compound
angles on the lid. But I pressed
on in Dave’s honor and managed
to complete the construction
while he was away at treatment.
When he returned, he
agreed to help me with the
finishing work. You might
think that staining and
varnishing a friend’s coffin
with him would feel awkward,
but it didn’t. In fact, I suspect
that we both welcomed it as
a way to help reconcile his
impending departure without
wrangling words. And it did
provide fodder for plenty
of future “pine box” jokes
to fend off the shadows.
Dave is still with us for the
moment, and bravely facing
down a 3% survival rate. As
one ex-Navy man to another,
I salute him. And I’m proud
that my work will carry him
toward his next port of call. ■
Outfeed
GIFTBy Jody Garrett
Friendship, honor, and
bravery in a pine box
D.I.Y. coffin. Even with sketchy plans, a determined
woodworker with basic equipment and a lot of heart
can craft a “pine box” worthy of a loved one. (If
possible, make them help you with the finish work!)
The Final
Jody Dave
72