Slant +/- 45° Dual-Polarized Panel Antennas806-900 MHz, 806-960 MHz

Model Number Frequency Range(MHz) H-Plane E-Plane Gain

(dBd)Fixed Electrical

Downtilt Options**Length x Width x Depth

(in inches)BXA-80040/4CF _ 806-900 MHz* 40° 15° 14.5 dBd 0°, 5° 47.2” x 23.6” x 7.9”BXA-80040/6CF _ 806-900 MHz* 40° 10° 16 dBd 0°, 6° 71.1” x 23.6” x 7.9”

BXA-80040/8BF _ 806-900 MHz* 40° 7° 18 dBd 0° 94.7” x 23.6” x 7.9”BXA-80040/8CF _ 806-900 MHz* 40° 7° 18 dBd 0°, 3°, 6° 94.7” x 23.6” x 7.9”BXA-80063/2CF _ 806-900 MHz* 63° 30° 10 dBd 0°, 3°, 5°, 7°, 9° 23.8” x 11.2” x 5.0”BXA-80063/4CF _ 806-900 MHz* 63° 15° 13 dBd 0°, 4°, 5°, 6° 47.4” x 11.2” x 5.0”BXA-80063/6BF _ 806-900 MHz* 63° 11° 14.5 dBd 15° 71.1” x 11.2” x 5.0”BXA-80063/6CF _ 806-900 MHz* 63° 11° 14.5 dBd 0°, 2°, 3°, 5°, 6° 71.1” x 11.2” x 5.0”BXA-80063/8CF _ 806-900 MHz* 63° 7° 16 dBd 0°, 2°, 3°, 5° 94.7” x 11.2” x 5.0”BXA-80080/4CF _ 806-900 MHz* 80° 15° 12 dBd 0° 48.2” x 11.2” x 5.9”BXA-80080/6CF _ 806-900 MHz* 80° 11° 13.5 dBd 0° 72.6” x 11.2” x 4.6”BXA-80080/8CF _ 806-900 MHz* 80° 7° 15 dBd 0° 96.5” x 11.2” x 5.9”BXA-80090/2CF _ 806-900 MHz* 90° 30° 8 dBd 0° 23.8” x 8.1” x 5.7”BXA-80090/4CF _ 806-960 MHz 90° 15° 11 dBd 0°, 2°, 4° 47.4” x 8.1” x 5.7”BXA-80090/6CF _ 806-900 MHz* 90° 11° 12.5 dBd 0°, 3°, 4° 71.1” x 8.1” x 5.7”BXA-80090/8BF _ 806-900 MHz* 90° 7° 14 dBd 0° 94.7” x 8.1” x 5.7”BXA-80090/8CF _ 806-900 MHz* 90° 7° 14 dBd 0°, 3°, 4°, 5° 94.7” x 8.1” x 5.7”

BXA- 800 90 / 4 CF E-DIN 4°

Electrical DowntiltConnector TypeNE is an elongated N connector.E-DIN is an elongated DIN connector

CF refers to a “Center-Fed” connector.BF refers to a “Bottom-Fed” connector.

Number of Dipole PairsAlso refers to approx. length in feet

Horizontal Beamwidth

Operating Frequency Range800 = Operates within 806-900 MHz

or 806-960 MHz

BXA-800 Series

The BXA (Broadband X-Pol Antenna) is a slant +/- 45° dual-polarized panel covering the 806-900 MHz and 806-960 MHz frequen-cy range. Our unique all mechanical design and patented, slotted dipole element ensure excellent overall performance with similarelectrical performance from both ports and consistent and repeatable performance from all production units of the same model.These characteristics contribute significantly to the overall quality of a carrier’s network. Antennas are available with fixed electricaldowntilt.

Design and Construction of the BXA-800 Panel:BXA antennas are manufactured with our exclusive 3T Technology, featuring single-piece, water-cut brass feedline assemblies forconsistent performance; a non-collinear system with access to each radiating element for control of the shaping of the vertical pat-tern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for evenheat dissipation to minimize plate warping and bending.Model Number Guide:

Amphenol Antel, Inc.

Model’s Currently Available:

*This model is also available for 870-960 MHz. Contact your sales representative for details.**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.When ordering replace “__” with the connector type (NE or E-DIN).

Slant +/- 45° Dual Polarized, Panel 40° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/4CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1200 mm 47.2 in

Width 600 mm 23.6 in

Depth Depth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 11.3 kg 25.0 lbs

Wind AreaFore/Aft 0.72 m2 7.8 ft2

Side 0.24 m2 2.6 ft2

Rated Wind Velocity (Safety factor 2.0)>272 km/hr >162 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1019 N 229.0 lbsSide 351 N 78.9 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 40° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/4CF __ 5°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1200 mm 47.2 in

Width 600 mm 23.6 in

Depth Depth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 11.3 kg 25.0 lbs

Wind AreaFore/Aft 0.72 m2 7.8 ft2

Side 0.24 m2 2.6 ft2

Rated Wind Velocity (Safety factor 2.0)>272 km/hr >162 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1019 N 229.0 lbsSide 351 N 78.9 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 40° / 16 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/6CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1805 mm 71.1 in

Width 600 mm 23.6 inDepthDepth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 17 kg 37.5 lbs

Wind AreaFore/Aft 1.08 m2 11.7 ft2

Side 0.36 m2 3.9 ft2

Rated Wind Velocity (Safety factor 2.0)>180 km/hr >112 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1543 N 347.0 lbsSide 545 N 122.5 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 10°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 40° / 16 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/6CF __ 6°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1805 mm 71.1 in

Width 600 mm 23.6 inDepthDepth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 17 kg 37.5 lbs

Wind AreaFore/Aft 1.08 m2 11.7 ft2

Side 0.36 m2 3.9 ft2

Rated Wind Velocity (Safety factor 2.0)>180 km/hr >112 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1543 N 347.0 lbsSide 545 N 122.5 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 10°1) Electrical Downtilt 6°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/8CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / centeror bottom

1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna can be ordered with center-fed or bottom-fed connectors.

Center-fed: BXA-80040/8CF + (NE or E-DIN)Bottom-fed: BXA-80040/8BF + (NE or E-DIN)

Length 2405 mm 94.7 in

Width 600 mm 23.6 in

DepthDepth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 22.7 kg 50.0 lbs

Wind AreaFore/Aft 1.44 m2 15.5 ft2

Side 0.48 m2 5.2 ft2

Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs

Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/8BF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 2405 mm 94.7 in

Width 600 mm 23.6 in

DepthDepth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 22.7 kg 50.0 lbs

Wind AreaFore/Aft 1.44 m2 15.5 ft2

Side 0.48 m2 5.2 ft2

Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / bottomor center

1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

BF Denotes a Bottom-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna can be ordered with bottom-fed orcenter-fed connectors.

Bottom-fed: BXA-80040/8BF + (NE or E-DIN)Center-fed: BXA-80040/8CF + (NE or E-DIN)

Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/8CF __ 3°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center 1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 2405 mm 94.7 in

Width 600 mm 23.6 in

DepthDepth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 22.7 kg 50.0 lbs

Wind AreaFore/Aft 1.44 m2 15.5 ft2

Side 0.48 m2 5.2 ft2

Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs

Slant +/- 45° Dual Polarized, Panel 40° / 18 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80040/8CF __ 6°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center 1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports ≤ -27 dB1) Gain 18 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 40°

E-Plane 7°1) Electrical Downtilt 6°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 2405 mm 94.7 in

Width 600 mm 23.6 in

DepthDepth with z-bracket

200240

mmmm

7.99.4

inin

4) Weight 22.7 kg 50.0 lbs

Wind AreaFore/Aft 1.44 m2 15.5 ft2

Side 0.48 m2 5.2 ft2

Rated Wind Velocity (Safety factor 2.0)>206 km/hr >128 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 2059 N 463.0 lbsSide 782 N 175.7 lbs

Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/2CF __

Revision Date: 7/30/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 604 mm 23.8 in

Width 285 mm 11.2 inDepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 2.2 kg 4.9 lbs

Wind AreaFore/Aft 0.18 m2 1.8 ft2

Side 0.08 m2 0.8 ft2

Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36211102

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 30°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/2CF __ 3°

Revision Date: 7/30/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 604 mm 23.8 in

Width 285 mm 11.2 inDepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 2.2 kg 4.9 lbs

Wind AreaFore/Aft 0.18 m2 1.8 ft2

Side 0.08 m2 0.8 ft2

Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36211102

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 30°1) Electrical Downtilt 3°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/2CF __ 5°

Revision Date: 7/30/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 604 mm 23.8 in

Width 285 mm 11.2 inDepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 2.2 kg 4.9 lbs

Wind AreaFore/Aft 0.18 m2 1.8 ft2

Side 0.08 m2 0.8 ft2

Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36211102

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 30°1) Electrical Downtilt 5°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/2CF __ 7°

Revision Date: 7/30/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 604 mm 23.8 in

Width 285 mm 11.2 inDepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 2.2 kg 4.9 lbs

Wind AreaFore/Aft 0.18 m2 1.8 ft2

Side 0.08 m2 0.8 ft2

Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36211102

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 30°1) Electrical Downtilt 7°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 10 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/2CF __ 9°

Revision Date: 7/30/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 604 mm 23.8 in

Width 285 mm 11.2 inDepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 2.2 kg 4.9 lbs

Wind AreaFore/Aft 0.18 m2 1.8 ft2

Side 0.08 m2 0.8 ft2

Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 248 N 56 lbsSide 110 N 25 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36211102

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 10 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 30°1) Electrical Downtilt 9°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/4CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1205 mm 47.4 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 4.5 kg 9.9 lbs

Wind AreaFore/Aft 0.36 m2 3.9 ft2

Side 0.15 m2 1.7 ft2

Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Refer to modelBXA-87063/4CF _.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/4CF __ 4°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1205 mm 47.4 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 4.5 kg 9.9 lbs

Wind AreaFore/Aft 0.36 m2 3.9 ft2

Side 0.15 m2 1.7 ft2

Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 15°1) Electrical Downtilt 4°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/4CF __ 5°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1205 mm 47.4 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 4.5 kg 9.9 lbs

Wind AreaFore/Aft 0.36 m2 3.9 ft2

Side 0.15 m2 1.7 ft2

Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 15°1) Electrical Downtilt 5°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 13 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/4CF __ 6°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1205 mm 47.4 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 4.5 kg 9.9 lbs

Wind AreaFore/Aft 0.36 m2 3.9 ft2

Side 0.15 m2 1.7 ft2

Rated Wind Velocity (Safety factor 2.0)>653 km/hr >406 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 522 N 117 lbsSide 244 N 54.5 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 15°1) Electrical Downtilt 6°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/6CF __

Revision Date: 11/21/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 11°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Refer to modelBXA-87063/6CF _.

Antenna available with center-fedconnectors only.

Length 1804 mm 71.1 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 6.8 kg 14.9 lbs

Wind AreaFore/Aft 0.51 m2 5.53 ft2

Side 0.23 m2 2.45 ft2

Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs

Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/6CF __ 2°

Revision Date: 11/21/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 11°1) Electrical Downtilt 2°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 1804 mm 71.1 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 6.8 kg 14.9 lbs

Wind AreaFore/Aft 0.51 m2 5.53 ft2

Side 0.23 m2 2.45 ft2

Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs

Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/6CF __ 3°

Revision Date: 11/21/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 11°1) Electrical Downtilt 3°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 1804 mm 71.1 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 6.8 kg 14.9 lbs

Wind AreaFore/Aft 0.51 m2 5.53 ft2

Side 0.23 m2 2.45 ft2

Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs

Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/6CF __ 5°

Revision Date: 11/21/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 11°1) Electrical Downtilt 5°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 1804 mm 71.1 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 6.8 kg 14.9 lbs

Wind AreaFore/Aft 0.51 m2 5.53 ft2

Side 0.23 m2 2.45 ft2

Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs

Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/6CF __ 6°

Revision Date: 11/21/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 11°1) Electrical Downtilt 6°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 1804 mm 71.1 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 6.8 kg 14.9 lbs

Wind AreaFore/Aft 0.51 m2 5.53 ft2

Side 0.23 m2 2.45 ft2

Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs

Slant +/- 45° Dual Polarized, Panel 63° / 14.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/6BF __ 15°

Revision Date: 11/21/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1804 mm 71.1 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 6.8 kg 14.9 lbs

Wind AreaFore/Aft 0.51 m2 5.53 ft2

Side 0.23 m2 2.45 ft2

Rated Wind Velocity (Safety factor 2.0)>318 km/hr >198 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 753 N 169.2 lbsSide 378 N 85 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / bottom1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 11°1) Electrical Downtilt 15°1) Null Fill 5%

Lightning Protection Direct Ground

BF Denotes a Bottom-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with bottom-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/8CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 2405 mm 94.7 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 10.9 kg 24.0 lbs

Wind AreaFore/Aft 0.70 m2 7.5 ft2

Side 0.30 m2 3.3 ft2

Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Refer to modelBXA-87063/8CF _.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/8CF __ 2°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 2405 mm 94.7 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 10.9 kg 24.0 lbs

Wind AreaFore/Aft 0.70 m2 7.5 ft2

Side 0.30 m2 3.3 ft2

Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 7°1) Electrical Downtilt 2°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/8CF __ 3°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 2405 mm 94.7 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 10.9 kg 24.0 lbs

Wind AreaFore/Aft 0.70 m2 7.5 ft2

Side 0.30 m2 3.3 ft2

Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 63° / 16 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80063/8CF __ 5°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 2405 mm 94.7 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

126166

mmmm

5.06.5

inin

4) Weight 10.9 kg 24.0 lbs

Wind AreaFore/Aft 0.70 m2 7.5 ft2

Side 0.30 m2 3.3 ft2

Rated Wind Velocity (Safety factor 2.0)>333 km/hr >207 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1048 N 236 lbsSide 556 N 125 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < - 30 dB1) Gain 16 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 63°

E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 80° / 12 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80080/4CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1225 mm 48.2 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

150190

mmmm

5.97.5

inin

4) Weight 6.5 kg 14.3 lbs

Wind AreaFore/Aft 0.35 m2 3.76 ft2

Side 0.18 m2 1.98 ft2

Rated Wind Velocity (Safety factor 2.0)>380 km/hr >236 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 500 N 112.3 lbsSide 277 N 62.2 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 80°

E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 80° / 13.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80080/6CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1844 mm 72.6 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

116156

mmmm

4.66.1

inin

4) Weight 10 kg 22.0 lbs

Wind AreaFore/Aft 0.53 m2 5.7 ft2

Side 0.21 m2 2.3 ft2

Rated Wind Velocity (Safety factor 2.0)>277 km/hr >172 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 765 N 172 lbsSide 366 N 82 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 13.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 80°

E-Plane 11°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 80° / 15 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80080/8CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 2450 mm 96.5 in

Width 285 mm 11.2 in

DepthDepth with z-bracket

150190

mmmm

5.97.5

inin

4) Weight 14 kg 31.0 lbs

Wind AreaFore/Aft 0.70 m2 7.50 ft2

Side 0.37 m2 3.96 ft2

Rated Wind Velocity (Safety factor 2.0)>188 km/hr >117 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 1160 N 238 lbsSide 632 N 142 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 15 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 80°

E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 8 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/2CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 604 mm 23.8 in

Width 204 mm 8.0 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 3.6 kg 8.0 lbs

Wind AreaFore/Aft 0.12 m2 1.3 ft2

Side 0.09 m2 0.9 ft2

Rated Wind Velocity (Safety factor 2.0)>800 km/hr >500 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 176 N 39.5 lbsSide 122 N 27.5 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36211102

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 8 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 30°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 11 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/4CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-960 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1205 mm 47.4 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 5.4 kg 12.0 lbs

Wind AreaFore/Aft 0.25 m2 2.7 ft2

Side 0.17 m2 1.9 ft2

Rated Wind Velocity (Safety factor 2.0)>679 km/hr >422 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 362 N 81.4 lbsSide 264 N 59.4 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-960 MHz

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 11 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 15°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 11 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/4CF __ 2°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1205 mm 47.4 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 5.4 kg 12.0 lbs

Wind AreaFore/Aft 0.25 m2 2.7 ft2

Side 0.17 m2 1.9 ft2

Rated Wind Velocity (Safety factor 2.0)>679 km/hr >422 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 362 N 81.4 lbsSide 264 N 59.4 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 11 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 15°1) Electrical Downtilt 2°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 11 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/4CF __ 4°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1205 mm 47.4 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 5.4 kg 12.0 lbs

Wind AreaFore/Aft 0.25 m2 2.7 ft2

Side 0.17 m2 1.9 ft2

Rated Wind Velocity (Safety factor 2.0)>679 km/hr >422 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 362 N 81.4 lbsSide 264 N 59.4 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 11 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 15°1) Electrical Downtilt 4°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 12.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/6CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1805 mm 71.1 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 8.2 kg 18.0 lbs

Wind AreaFore/Aft 0.37 m2 3.9 ft2

Side 0.26 m2 2.8 ft2

Rated Wind Velocity (Safety factor 2.0)>452 km/hr >281 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 558 N 126.0 lbsSide 433 N 97.4 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 11°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 12.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/6CF __ 3°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Featuring upper sidelobe suppression.

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1805 mm 71.1 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 8.2 kg 18.0 lbs

Wind AreaFore/Aft 0.37 m2 3.9 ft2

Side 0.26 m2 2.8 ft2

Rated Wind Velocity (Safety factor 2.0)>452 km/hr >281 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 558 N 126.0 lbsSide 433 N 97.4 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 11°1) Electrical Downtilt 3°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 12.5 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/6CF __ 4°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 1805 mm 71.1 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 8.2 kg 18.0 lbs

Wind AreaFore/Aft 0.37 m2 3.9 ft2

Side 0.26 m2 2.8 ft2

Rated Wind Velocity (Safety factor 2.0)>452 km/hr >281 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 558 N 126.0 lbsSide 433 N 97.4 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 12.5 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 11°1) Electrical Downtilt 4°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/8CF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Refer to modelBXA-87090/8CF _.

Antenna can be ordered with center-fed orbottom-fed connectors.

Center-fed: BXA-80090/8CF + (NE or E-DIN)Bottom-fed: BXA-80090/8BF + (NE or E-DIN)

Length 2405 mm 94.7 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 10.4 kg 23.0 lbs

Wind AreaFore/Aft 0.49 m2 5.3 ft2

Side 0.35 m2 3.8 ft2

Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs

Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/8BF __

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specificationsLength 2405 mm 94.7 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 10.4 kg 23.0 lbs

Wind AreaFore/Aft 0.49 m2 5.3 ft2

Side 0.35 m2 3.8 ft2

Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / bottomor center

1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 7°1) Electrical Downtilt 0°1) Null Fill 5%

Lightning Protection Direct Ground

BF Denotes a Bottom-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna can be ordered with bottom-fed orcenter-fed connectors.

Bottom-fed: BXA-80090/8BF + (NE or E-DIN)Center-fed: BXA-80090/8CF + (NE or E-DIN)

Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/8CF __ 3°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 7°1) Electrical Downtilt 3°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 2405 mm 94.7 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 10.4 kg 23.0 lbs

Wind AreaFore/Aft 0.49 m2 5.3 ft2

Side 0.35 m2 3.8 ft2

Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs

Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/8CF __ 4°

Revision Date: 7/20/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 7°1) Electrical Downtilt 4°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 2405 mm 94.7 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 10.4 kg 23.0 lbs

Wind AreaFore/Aft 0.49 m2 5.3 ft2

Side 0.35 m2 3.8 ft2

Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs

Slant +/- 45° Dual Polarized, Panel 90° / 14 dBd

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

BXA-80090/8CF __ 5°

Revision Date: 7/3/07

When ordering replace “___” with connector type.

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110 -100 -90 -80 -70-60

-50

-40

-30

-20

-10

5101520253035

Radiation pattern1)

Horizontal

0

10

20

30

40

50 60

70 80 90100110120

130

140

150

160

170

180

-170

-160

-150

-140

-130-120

-110-100 -90 -80

-70-60

-50

-40

-30

-20

-10

5101520253035

Vertical

Radiation patterns for all antennas aremeasured with the antenna mounted ona fiberglass pole.

Mounting on a metal pole will typicallyimprove the Front-to-Back ratio.

806-900 MHz

Amphenol Antel’sExclusive 3T (TrueTransmission LineTechnology)Antenna Design:

This Amphenol Antel antenna is under a five-year limited warranty for repair or replacement.

Mechanical specifications

Antenna consisting of aluminum alloy with brassfeedlines covered by a UV safe fiberglass radome.

Mounting and DowntiltingMounting brackets attach to a pipe diameter ofØ50-160 mm (2.0-6.3 in).

Mounting bracket kit #36210002Downtilt bracket kit #36114003

Electrical specifications

1) Typical values.2) Power rating limited by connector only.3) NE indicates an elongated N connector.

E-DIN indicates an elongated DIN connector.4) The antenna weight listed above does not include

the bracket weight.Improvements to mechanical and/or electrical performance of the antenna may be made without notice.

Patented Dipole Design: U.S. Patent No. 6,608,600 B2

Frequency Range 806-900 MHz*

Impedance 50Ω3) Connector(s) NE or E-DIN

2 ports / center1) VSWR ≤ 1.4:1

Polarization Slant ± 45°1) Isolation Between Ports < -30 dB1) Gain 14 dBd2) Power Rating 500 W1) Half Power Angle

H-Plane 90°

E-Plane 7°1) Electrical Downtilt 5°1) Null Fill 5%

Lightning Protection Direct Ground

CF Denotes a Center-FedConnector.

Watercut brass feedline assembly forconsistent performance.

Unique feedline design eliminates the needfor conventional solder joints in the signalpath.

A non-collinear system with access toevery radiating element for broad band-width and superior performance.

Air as insulation for virtually no internal signal loss.

*Also available for 870-960 MHz. Consult yoursales director for more information.

Antenna available with center-fedconnectors only.

Length 2405 mm 94.7 in

Width 205 mm 8.1 in

DepthDepth with z-bracket

145185

mmmm

5.77.3

inin

4) Weight 10.4 kg 23.0 lbs

Wind AreaFore/Aft 0.49 m2 5.3 ft2

Side 0.35 m2 3.8 ft2

Rated Wind Velocity (Safety factor 2.0)>323 km/hr >201 mph

Wind Load @ 100 mph (161 km/hr)Fore/Aft 793 N 178.4 lbsSide 591 N 132.9 lbs

1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001 Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

Mounting & Downtilt Bracket Kits

BXA Bracket Kits Part Number Bracket Type

36210002 Standard BXA Mounting Bracket Kit for: BXA-80040/4CF BXA-80080/4CF BXA-80040/6CF BXA-80080/6CF BXA-80040/8BF BXA-80080/8CF BXA-80040/8CF BXA-80090/2CF BXA-80063/2CF BXA-80090/4CF BXA-80063/4CF BXA-80090/6CF BXA-80063/6BF BXA-80090/8BF BXA-80063/6CF BXA-80090/8CF BXA-80063/8CF 36211102 Standard BXA *Downtilt Bracket Kit for: BXA-80063/2CF BXA-80090/2CF 36114003 Standard BXA *Downtilt Bracket Kit for: BXA-80040/4CF BXA-80080/4CF BXA-80040/6CF BXA-80080/6CF BXA-80040/8BF BXA-80080/8CF BXA-80040/8CF BXA-80090/4CF BXA-80063/4CF BXA-80090/6CF BXA-80063/6BF BXA-80090/8BF BXA-80063/6CF BXA-80090/8CF BXA-80063/8CF

*Both the downtilt bracket kit and the standard mounting bracket kit must be

ordered for mechanical downtilt applications.

Mounting Bracket Kits are sold separately and not included in the price of antennas.

R

WA

ANTE

NN

A

R

WA

ANTE

NN

A

36210002 Top View Side View

36211102 Top View Side View

R

WA

ANTE

NN

A

36114003 Top View Side View