Upload
fernando-pauwels
View
235
Download
0
Embed Size (px)
Citation preview
7/27/2019 Canon HF G10 manual
1/184
PUB. DIM-1009-000A
English
Franais
Espaol
stHD Camcorder
Instruction Manual
Camscope HDManuel d'instruction
Videocmara HD
Manual de Instrucciones
7/27/2019 Canon HF G10 manual
2/184
2
Introduction
Important Usage Instructions
WARNING!TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING!
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE RECOMMENDEDACCESSORIES ONLY.
COPYRIGHT WARNING:Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be contrary to copyrightlaws.
HD Camcorder, VIXIA HF G10 A systems
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, usesand can radiate radio frequency energy and, if not installed and use in accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications shouldbe made, you could be required to stop operation of the equipment.
Canon U.S.A., Inc.One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
WARNING:To reduce the risk of electric shock, do not expose this product to dripping or splashing.
The Mains plug is used as the disconnect device. The Mains plug shall remain readily operable to disconnect the plug in case of an accident.
CAUTION: Danger of explosion if the wrong type of batteries are attached. Use only the same type of batteries. Do not expose batteries or product to excessive heat such as the inside of a car under direct sunlight, fire, etc.
mportant arn ng
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOTREMOVE COVER (OR BACK). NO USER-SERVICEABLEPARTS INSIDE. REFER SERVICING TO QUALIFIEDSERVICE PERSONNEL.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to a lert the userto the presence of uninsulated dangerousvoltage within the products enclosure, that maybe of sufficient magnitude to constitute a risk ofelectric shock to persons.
The exclamation point, within an equila teraltriangle, is intended to alert the user to thepresence of important operating and maintenance(servicing) instructions in the literatureaccompanying the product.
7/27/2019 Canon HF G10 manual
3/184
3
In these safety instructions the word product refers to the Canon HD Camcorder VIXIA HF G10 A and all its accessories.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) thatproduce heat.
8 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than theother. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for yoursafety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
9 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where theyexit from the apparatus.
10 Only use attachments/accessories specified by the manufacturer.
11 Unplug this apparatus during lightning storms or when unused for long periods of time.
12 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such aspower-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has beenexposed to rain or moisture, does not operate normally, or has been dropped.
13 Read Instructions All the safety and operating instructions should be read before the product is operated.
14 Retain Instructions The safety and operating instructions should be retained for future reference.
15 Heed Warnings All warnings on the product and in the operating instructions should be adhered to.
16 Follow Instructions All operating and maintenance instructions should be followed.
17 Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. The product should becleaned only as recommended in this manual.
18 Accessories Do not use accessories not recommended in this manual as they may be hazardous.
19 Avoid magnetic or electric fields Do not use the camera close to TV transmitters, portable communication devices or othersources of electric or magnetic radiation. They may cause picture interference, or permanently damage the camera.
20 Water and Moisture Hazard of electric shock Do not use this product near water or in rainy/moist situations.
21 Placing or Moving Do not place on an unstable cart, stand, tripod, bracket or table. The product may fall,causing serious injury to a child or adult, and serious damage to the product.A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfacesmay cause the product and cart combination to overturn.
22 Power Sources The CA-570 Compact Power Adapter should be operated only from the type of power sourceindicated on the marking label. If you are not sure of the type of power supply to your home, consult yourproduct dealer or local power company. Regarding other power sources such as battery power, refer toinstructions in this manual.
23 Polarization The CA-570 Compact Power Adapter is equipped with a polarized 2-prong plug (a plug having one blade widerthan the other). The 2-prong polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable toinsert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsoleteoutlet. Do not defeat the safety purpose of the polarized plug.
24 Power Cord Protection Power cords should be routed so that they are not likely to be walked on or pinched by items placedupon or against them. Pay particular attention to plugs and the point from which the cords exit the product.
25 Outdoor Antenna Grounding If an outside antenna is connected tothe product, be sure the antenna is grounded so as to provide someprotection against voltage surges and built-up static charges. Section810 of the National Electrical Code, ANSI / NFPA No. 701984,provides information with respect to proper grounding of the mast andsupporting structure, grounding of the lead-in wire to an antennadischarge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirementsfor the grounding electrode. See figure 1.
26 Lightning For added protection of this product during a lightningstorm, or when it is left unattended and unused for long periods oftime, disconnect it from the wall outlet and disconnect the antenna.This will prevent damage to the product due to l ightning and power-line surges.
27 Overloading Do not overload wall outlets and extension cords asthis can result in a risk of fire or electric shock.
IMPORTANT SAFETY INSTRUCTIONS
EXAMPLE OF ANTENNA GROUNDING ASPER NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGEUNIT (NEC SECTION810-20)
GROUNDINGCONDUCTORS(NEC SECTION 810-21)
GROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250. PART H)
NEC - NATIONALELECTRICAL CODE
ELECTRICSERVICEEQUIPMENT
GROUNDCLAMP
Fig. 1
7/27/2019 Canon HF G10 manual
4/184
4
28 Objects and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerousvoltage points or short out parts that could result in a fire or electric shock. Be careful not to spill liquid of any kind onto theproduct.
29 Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltageor other hazards. Refer all servicing to qualified service personnel.
30 Damage Requiring Service Disconnect this product from the wall outlet and all power sources including battery, and referservicing to qualified service personnel under the following conditions:a. When the power-supply cord or plug is damaged.b. If any liquid has been spilled onto, or objects have fallen into, the product.
c. If the product has been exposed to rain or water.d. If the product does not operate normally even if you follow the operating instructions.Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result indamage and will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.f. When the product exhibits a distinct change in performance. This indicates a need for service.
31 Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts that arespecified by Canon or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electricshock or other hazards.
32 Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks todetermine that the product is in safe operating order.
33 Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat.
CA-570 identification plate is located on the bottom.
This Class B digital apparatus complies with Canadian ICES-003.
Trademark Acknowledgements SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC. Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
x.v.Color and the x.v.Color logo are trademarks. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries. AVCHD and the AVCHD logo are trademarks of Panasonic Corporation and Sony Corporation. Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories. YouTube is a trademark of Google Inc. Other names and products not mentioned above may be trademarks or registered trademarks of their
respective companies.
This device incorporates exFAT technology licensed from Microsoft. ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER THAT COMPLIES WITH THE MPEG-2
STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDERAPPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE
STREET, SUITE 300, DENVER, COLORADO 80206. This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding MPEG-4 compliant video and/or
decoding MPEG-4 compliant video that was encoded only (1) for a personal and non-commercial purpose or (2) by a video providerlicensed under the AT&T patents to provide MPEG-4 compliant video. No license is granted or implied for any other use for MPEG-4
standard.
7/27/2019 Canon HF G10 manual
5/184
5
Highlights of the VIXIA HF G10
The Canon VIXIA HF G10 HD Camcorder is a high-performance camcorder whose compact size
makes it ideal in a variety of situations. The following are just some of the many functions featured inthe camcorder.
HD Recording
HD CMOS PRO and DIGIC DV III
processorThe camcorder is equipped with a1/3-inch CMOS sensor that captures video atan effective pixel count of approximately 2.07
megapixels (1920x1080). The video is thenprocessed by the state-of-the-art DIGIC DV IIIimage processor. This allows the camcorder to
excel in low-light situations and produce awide dynamic range.
Wide zoom lensWith a focal length at full wide angle of
30.4 mm (35 mm equivalent), the camcorderhas superb wide-angle shooting capability. Theminimum object distance is 60 cm (2 ft.)
throughout the entire zoom range, whichmeans that you can create a pleasing blurredbackground effect at full telephoto. The
8-bladed iris aperture also enhances theblurred background effect.
Shoot cinematic videoUsing CINEMA mode and the cinema-look
filters (0 101), you can make recordings thattruly look and feel cinematic.
Operability
Emphasis on versatilityThis camcorder has features to make it usableas a main camera but is also small enough tobe very portable. The advanced image
stabilization (0 54) will let you shoot in avariety of situations in the field.
Manual controls at your fingertipsThe focus ring helps you achieve the focus you
are looking for. Furthermore, you can assigncertain frequently used functions to acustomizable button and adjust those
functions with the accompanying dial (0 83).
Face detectionWhen a subject's face is detected, thecamcorder can track and focus on it (0 48).Furthermore, you can have the camcorder in
manual focus but switch to autofocus onlywhen a face is detected, ensuring thatimportant subjects are in focus.
Relay recording and double slot
recordingWhen you use relay recording (0 34), you
can use the double memory card slot to keepon recording video without interruption. Doubleslot recording (0 35) allows you to record
movies simultaneously to two memory cards,which is a convenient way to back up yourrecordings.
Other Features
Smart AUTOSmart AUTO (0 39) automatically selects thebest scene mode for the scene you want to
shoot. You get spectacular recordings everytime without worrying about settings.
LCD screen and viewfinderThe LCD screen and viewfinder both have
100% frame coverage, which will ensure thatyou can accurately check that your shots areframed how you want them.
Touch AEBy simply touching the screen, you can makedark areas in the picture appear brighter(0 59). This operation is simple yet allows
you to shoot with the desired exposure.
Added and improved functionalityOther functions include two types of videoscopes (0 78), conversion to standard
definition (0 133) and Story Creator mode(0 98), which allows you to createengrossing video stories.
7/27/2019 Canon HF G10 manual
6/184
6
Enjoying your Recordings on Other Devices
Eye-Fi
Connect the camcorder to anHDTV (0 120) Play video directly
from your recordedmemory card
AVCHD-compatible HDTVs anddigital recorders with a card slotcompatible with the type of
memory card used*.
Use an Eye-Fi card (0 136)to wirelessly upload
recordings to your computeror a video sharing Web site.
Save or upload tothe Web.
Standard Definition
Convert your HD movies, in the camcorder itself, to standarddefinition files (0 133).
High Definition
Use the supplied PIXELAssoftware (0 128, 133).
Create discs
* Refer to the instruction manual of the device. Depending on the device used, correct playback maynot be possible even if the device is AVCHD-compatible. In such case, play back the recordings on thememory card using the camcorder.
7/27/2019 Canon HF G10 manual
7/184
7
1 Introduction 10
About this Manual 10Conventions Used in this Manual 10
Supplied Accessories and CD-ROMs 12
Names of Parts 14
2 Preparations 20
Charging the Battery Pack 20
Preparing the Camcorder 22Attaching the Lens Hood 22Using the Viewfinder 22
Adjusting the Position and Brightness of
the LCD Screen 23
Wireless Controller 25Using a Tripod 25
Basic Operation of the Camcorder 26Using the Touch Screen 26Operating Modes 27
Using the Menus 28
First Time Settings 30Setting the Date and Time 30
Changing the Language 30Changing the Time Zone 31
Using a Memory Card 32Memory Cards Compatible for Use with
the Camcorder 32Inserting and Removing a Memory
Card 33Selecting the Memory for the
Recordings 34
Relay Recording 34Double Slot Recording 35Initializing the Memory 36
3 Recording 37
Recording Movies and Photos 37Preparing to Record 37
Recording in AUTO Mode 38Recording iny (Manual) Mode 41
Quick Start Function 43
Selecting the Video Quality (RecordingMode) 44
Selecting the Frame Rate 45
Focus Adjustment 46
Manual Focus 46Autofocus 47Face Detection 48
Touch & Track 50
Zooming 51Using the Zoom Lever or Wireless
Controller 51
Using the Touch Screens ZoomControls 52
Soft Zoom Control 53Digital Tele-Converter 53
Advanced Image Stabilization 54
Automatic Gain Control (AGC) Limit 55
Automatic Exposure RecordingPrograms 56
Exposure Adjustment 58Using the Manual Exposure Recording
Program 58
Exposure Compensation 59White Balance 61
Special Scene Recording Programs 63
Image Effects 65
Self Timer 66
Audio Recording Level 67
Built-In Microphone Directionality 68
Audio Equalizer 69
Audio Mix 70
Using Headphones 71
Using the Mini Advanced Shoe 72Using an External Microphone 73
Using the SM-V1 Surround Microphoneor DM-100 Directional StereoMicrophone 73
Using the WM-V1 WirelessMicrophone 73
Using Commercially Available
Microphones 74
Using an External Video Light 75
Using a Zoom Remote Controller 76
Color Bars/Audio Reference Signal 77
Video Scopes 78Displaying the Waveform Monitor during
[A Programmed AE] RecordingProgram 78
Displaying the Waveform Monitor during
[y Manual Exposure] RecordingProgram 78
Displaying the Edge Monitor 78
Video Snapshot 79
Pre-Recording 80Onscreen Displays and Data Code 81
Faders 82
Table of contents
7/27/2019 Canon HF G10 manual
8/184
8
4 Customization 83
Custom Button and Dial 83
Assignable Buttons 84
Changing the Assigned Function 84Using an Assignable Button 84
Saving and Loading Menu Settings 85Saving Menu Settings to a Memory
Card 85
Loading Camera Settings from a MemoryCard 85
5 Playback 86
Playing Back Video 86
Adjusting the volume 883D Flip View 89
The Index Selection Screen: Selecting theContent to Play Back 90
Deleting Scenes and Stories 91Deleting a Single Scene 91
Deleting Scenes from the Date IndexScreen 91
Deleting a Single Scene from a Story 92
Deleting Scenes from a Story by
Rating 92Deleting Stories 92
Dividing Scenes 94
Selecting the Playback Starting Point 95
Capturing Video Snapshot Scenes andPhotos from a Movie 96Capturing a Video Snapshot Scene 96Capturing Photos 97
6 Video Stories and Cinema
Style 98
Using Story Creator to Create VideoStories 98Creating a New Story 98Recording a Scene within a Story 99Recording Additional Scenes within an
Existing Story 100
CINEMA Mode and Cinema-LookFilters 101
Adding Decorations 103Decorating Scenes while
Recording 103
Decorating Scenes duringPlayback 107
Playing Back Stories from theGallery 108
Rating Scenes 110Rating Scenes from the List of
Scenes 110Rating Scenes During Playback 110
Playback with Background Music 111Using One of the Supplied Music Tracks
as Background Music 111
Using an External Audio Player forBackground Music 112
Copying and Moving Scenes Within/Between Stories 114
Selecting a Storys Thumbnail Image 115
Changing a Storys Title 116
7 External Connections 117
Terminals on the Camcorder 117
Connection Diagrams 118
Playback on a TV Screen 120
7/27/2019 Canon HF G10 manual
9/184
9
8 Photos 121
Viewing Photos 121Photo Jump Function 122
Deleting Photos 123Deleting a Single Photo 123
Deleting Photos from the IndexScreen 123
Slideshow 124
9 Saving/Sharing
Recordings 125
Copying Recordings to a MemoryCard 125Copying Scenes from the Date Index
Screen 125Copying Scenes from a Story by
Rating 126
Copying a Single Photo 126Copying Photos from the Index
Screen 126
Saving Recordings on a Computer 128Saving Movies (Windows only) 128Saving Photos (Windows/Mac OS) 129
Copying Recordings to an External VideoRecorder 131In High Definition 131In Standard Definition 131
Uploading Movies to Video Sharing WebSites 133Converting Scenes into Standard
Definition from the Date Index
Screen 133Connecting to the Computer and
Uploading your Videos 134
Converting Scenes into StandardDefinition from a Story by Rating 135
Converting Only Part of a Scene or
Story 135Uploading your Videos Wirelessly 136
10 Additional Information 138
Appendix: Menu Options Lists 138FUNC. Panel 138
Setup Menus 140Appendix: Onscreen Icons and
Displays 149
Troubleshooting 153List of Messages 158
Handling Precautions 164Camcorder 164Battery Pack 165Memory Card 165
Built-in Rechargeable Lithium
Battery 166Lithium Button Battery 166
Disposal 166
Maintenance/Others 167Cleaning 167
Condensation 167Using the Camcorder Abroad 168
Accessories 169Optional Accessories 170
Product Codes 174
Specifications 175
Index 179
7/27/2019 Canon HF G10 manual
10/184
About this Manual
10
Introduction
About this ManualThank you for purchasing the Canon VIXIA HF G10. Please read this manual carefully before you use
the camcorder and retain it for future reference. Should your camcorder fail to operate correctly, referto Troubleshooting (0 153).
Conventions Used in this Manual
IMPORTANT: Precautions related to the camcorders operation.
NOTES: Additional topics that complement the basic operating procedures.
POINTS TO CHECK: Restrictions or requirements regarding the function described. 0: Reference page number within this manual.
rReferences to sections of the Photo Application Instruction Manual, included as a PDF filein the supplied Camcorder Supplemental Disc.
The following terms are used in this manual:When not specified as memory card or built-in memory, the term memory by itself refers toboth.Scene refers to one movie unit from the point you press theg button to start recordinguntil you press again to pause the recording.
The photos included in this manual are simulated pictures taken with a still camera.
Some screenshots in this manual have been simplified to show only relevant icons.
1 Introduction
7/27/2019 Canon HF G10 manual
11/184
About this Manual
11
Self Timer
Self Timer
1 Open the [Self Timer] screen.
[FUNC.] [MENU] 8 [Self Timer]
2 Touch [A Onn] and then touch [a].
n will appear on the screen.
Repeat, selecting [B Off], to turn off the self timer.
Movies: In record pause mode, pressg.
The camcorder starts recording after a 10-second countdown*. The countdown appears on the
screen.
Photos: In record pause mode, touch [PHOTO].The camcorder will record the photo after a 10-second countdown*. The countdown appears on the
screen.
* 2 secon i i l roller.
ions will cancel the self timer.
Operating modes:
Brackets [ ] are used to refer to controlbuttons and menu options you will
touch on the screen and to other
onscreen messages and displays.
indicates that a function is available in theoperating mode indicated and indicates
that the function is not available. For a detailed
explanation refer to Operating Modes (0 27).
The names of physical buttons
and switches on the camcorderare indicated within a buttonframe.
For exampleh.
The arrow is used to abbreviate menu selections. For adetailed explanation on how to use the menus, refer toUsing the Menus (0 28). For a concise summary of all
available menu options and settings, refer to theappendix Menu Options Lists (0 138).
7/27/2019 Canon HF G10 manual
12/184
Supplied Accessories and CD-ROMs
12
Supplied Accessories and CD-ROMs
The following accessories are supplied with the camcorder:
CA-570 Compact Power Adapter(incl. power cord)
BP-808 Battery Pack WL-D89 Wireless Controller(incl. CR2025 lithium button battery)
Stylus Pen HTC-100/S HDMI Cable STV-250N Stereo Video Cable
IFC-300PCU/S USB Cable Lens hood Lens cap
Installation Guide for PIXELAsSoftware
7/27/2019 Canon HF G10 manual
13/184
Supplied Accessories and CD-ROMs
13
The following CD-ROMs and software are supplied with the camcorder:
PIXELAs Transfer Utility CD-ROM*
- Use Transfer Utility for saving and transferring movies and music files you can use as
background music. PIXELAs VideoBrowserCD-ROM*
- In addition to all the functionality ofTransfer Utility, you can useVideoBrowserfor managing,editing, and playing back movies.
Photo Applications Ver.35*/Music Data/Image Mix Data CD-ROM (referred in the manual asCamcorder Supplemental Disc). Contains the following components.
- Photo Application - Software for saving, managing, and printing photos.- Music data - Music files that can be used as background music during playback. These music
files are for exclusive use with the supplied PIXELAs software. The disc cannot be played back on
CD players.
- Image mix data - Image files that can be used with the image mix function (image mix frames).* The CD-ROM includes the instruction manual of the software (on PDF file).
7/27/2019 Canon HF G10 manual
14/184
Names of Parts
14
Names of Parts
1 RESET button (0 156)2 2 (camera/play) button (0 27)3 DISP. (onscreen display) button
(0 81)/BATT. INFO (battery info)button (0 152)
4 Double memory card slot cover5 Memory card slot X (0 33)
6 Memory card slot Y (0 33)
7 AV OUT terminal (0 117,119)/X (headphones) terminal (0 71)
8 COMPONENT OUT terminal(0 117, 118)
9 Focus ring (0 46)10 Lens hood (0 22)
8 7
10 9
21 3 4
5 6
Left side view
7/27/2019 Canon HF G10 manual
15/184
Names of Parts
15
1 MIC terminal (0 74)2 Grip belt (0 24)3 USB terminal (0 117, 119, 131)
4 HDMI OUT terminal (0 117, 118)5 REMOTE terminal (0 76)6 Built-in speaker (0 88)
6
2 1
5 4 3
Right side view
7/27/2019 Canon HF G10 manual
16/184
Names of Parts
16
1 Instant AF sensor (0 167)2 Viewfinder (0 22)3 START/STOP button (0 37)4 Strap mount (0 24)5 DC IN terminal (0 20)6 Dioptric adjustment lever (0 22)
7 CUSTOM (customizable) dial (0 83)8 CUSTOM (customizable) button
(0 83)
9 LCD touch screen (0 23, 26)10 POWERED IS button (0 54)/
Assignable button 2 (0 84)11 AF/MF button (0 46)/
WEB button (0 133)/Assignable button 1 (0 84)
12 Remote sensor (0 25)
1
2
3
4
579 8 6
12
11
10
Front view
Back view
7/27/2019 Canon HF G10 manual
17/184
Names of Parts
17
1 Built-in microphone (0 68)2 Zoom lever (0 51)3 Mode switch (0 27)4 Mini advanced shoe5 ACCESS indicator (0 37)6 ON/OFF (CHG) indicator (0 20)
Green - ONOrange - Standby (0 43)Red - Charging (0 20)
7 POWER button
321
5
4
6
7
Top view
7/27/2019 Canon HF G10 manual
18/184
Names of Parts
18
1 Serial number
2 BATTERY RELEASE switch (0 21)3 Tripod socket (0 25)
23
1
Bottom view
7/27/2019 Canon HF G10 manual
19/184
Names of Parts
19
Wireless Controller WL-D89
1 START/STOP button (0 37)2 b (index selection) button (0 90)
Press and hold for more than 2 seconds to switch between shooting and playback mode.
3 MENU button (0 29, 140)
4 DISP. (onscreen display) button (0 81)5 SET button6 B (stop) button (0 86)7 PHOTO button (0 37)8 Zoom buttons (0 51)9 Navigation buttons (Z/O/y/A )10 A/C (play/pause) button (0 86)
1
7
8
9
10
2
3
4
5
6
7/27/2019 Canon HF G10 manual
20/184
Charging the Battery Pack
20
Preparations
Charging the Battery PackThe camcorder can be powered with a battery pack or directly using the compact power adapter. The
first time you use a battery pack, fully charge it and then use the camcorder until the battery pack iscompletely exhausted. Doing so will ensure that the remaining recording time will be displayedaccurately.
For approximate charging times and recording/playback times with a fully charged battery pack, referto Charging,Recording and Playback Times (0 170).
1 Connect the power cord to the compact power adapter.
2 Plug the power cord into a power outlet.
3 Connect the compact power adapter to the camcorders
DC IN terminal.
4 Attach the battery pack to the camcorder.
Press the battery pack softly into the battery attachmentunit and slide it forward until it clicks in place.
5 Charging will start when the camcorder is turned off.
If the camcorder was on, the green ON/OFF (CHG)
indicator will go out when you turn off the camcorder. Aftera moment, the ON/OFF (CHG) indicator will start flashing inred (battery pack charging). The red ON/OFF (CHG)
indicator will go out when the battery pack is fully charged.
If the indicator flashes quickly, refer to Troubleshooting
(0 155).
DC IN terminal
ON/OFF (CHG) (charge) indicator
2 Preparations
7/27/2019 Canon HF G10 manual
21/184
Charging the Battery Pack
21
To remove the battery pack
1 SlideU in the direction of the arrow andhold it pressed down.
2 Slide the battery pack and then pull it out.
IMPORTANT
Turn off the camcorder before connecting or disconnecting the compact power adapter. Afterpressingx to turn off the camcorder, important data is updated in the memory. Be sure to
wait until the green ON/OFF (CHG) indicator goes out.
Do not connect to the camcorders DC IN terminal or to the compact power adapter any electrical
equipment that is not expressly recommended for use with this camcorder.
To prevent equipment breakdowns and excessive heating, do not connect the supplied compact
power adapter to voltage converters for overseas travels or special power sources such as those onaircraft and ships, DC-AC inverters, etc.
NOTES
We recommend charging the battery pack in temperatures between 10 C and 30 C (50 F and86 F). If either the ambient temperature or the battery packs temperature is outside the range ofapprox. 0 C to 40 C (32 F to 104 F), charging will not start.
The battery pack will be charged only when the camcorder is off.
If the power supply was disconnected while charging a battery pack, make sure the ON/OFF (CHG)indicator has gone out before restoring the power supply.
If remaining battery time is an issue, you can power the camcorder using the compact poweradapter so the battery pack will not be consumed.
Charged battery packs continue to discharge naturally. Therefore, charge them on the day of use, orthe day before, to ensure a full charge.
We recommend that you prepare battery packs to last 2 to 3 times longer than you think you mightneed.
USA and Canada only: The Lithium ion/polymer battery that powers the product isrecyclable. Please call 1-800-8-BATTERY for information on how to recycle thisbattery.
BATTERYRELEASE
switch
7/27/2019 Canon HF G10 manual
22/184
Preparing the Camcorder
22
Preparing the Camcorder
This section covers the basic preparations for the camcorder such as attaching the lens hood,
adjusting the grip belt and adjusting the viewfinder and LCD screen. When attaching the lens hood,grip belt and straps, be careful not to drop the camcorder.
Attaching the Lens Hood
Attach the lens hood to protect the lens and reduce the amountof stray light that may hit the lens. Remove the lens cap before
attaching the lens hood.
Place the lens hood on the front of the lens so that the
groove on the lens hood is aligned with the bottom of thelens (), and then turn the lens hood clockwise (). Be careful not to deform the lens hood.
Make sure that the lens hood is aligned with the thread.
Using the ViewfinderIf it is difficult to use the LCD screen while the LCD backlight is on (0 23), you can use the viewfinder.
You can also use the viewfinder when you rotate the LCD panel 180 degrees to let the subject watchthe recording.
1 Pull out the viewfinder.
2 Pressx to turn on the camcorder.
3 Adjust the viewfinder using the dioptric adjustment
lever.
You can close the LCD panel or rotate it toward the
subject as you prefer.
The LCD backlight setting (0 23) is common to the LCD
screen and the viewfinder.
NOTES
For details about how to take care of the viewfinder, refer toHandling Precautions (0 164), Cleaning (0 167).
Dioptric adjustment lever
7/27/2019 Canon HF G10 manual
23/184
Preparing the Camcorder
23
Adjusting the Position and Brightness of the LCD Screen
Rotating the LCD Panel
Open the LCD panel 90 degrees.
You can rotate the panel 90 degrees downward. You can rotate the panel 180 degrees toward the lens. Rotating the LCD panel 180 degrees can be
useful in the following cases:- To allow the subject to monitor the LCD screen while you use the viewfinder.- To include yourself in the picture when recording with the self timer.
- To allow the camcorder to be operated with the wireless controller from the front.
NOTES
About the LCD and viewfinder screens: The screens are produced using extremely high-precision
manufacturing techniques, with more than 99.99% of the pixels operating to specification. Lessthan 0.01% of the pixels may occasionally misfire or appear as black, red, blue or green dots. Thishas no effect on the recorded image and does not constitute a malfunction.
LCD Backlight
When recording in bright places it may be difficult to use the LCD screen. Turn on the LCD backlight to
make it brighter.
With the camcorder on, holdh pressed down for morethan 2 seconds.
Repeat this action to switch the LCD backlight between off
(normal) and on (bright).
180
90Subject can monitor the LCD screen(You can use the viewfinder at the same time)
180
7/27/2019 Canon HF G10 manual
24/184
Preparing the Camcorder
24
NOTES
Using the bright setting will shorten the effective usage time of the battery pack.
You can further adjust the brightness of the LCD screen with the6 [LCD Brightness] setting,or dim it with the6 [LCD Screen Dimmer] setting to use in places where the light from theLCD screen can be a nuisance.
Adjusting the brightness does not affect the brightness of the recordings.
For details about how to take care of the touch screen, refer to Handling Precautions (0 164),Cleaning (0 167).
Grip Belt and Straps
Fasten the grip belt.
Adjust the grip belt so that you can reach the zoom leverwith your index finger, and theg button with your
thumb.
You can attach the supplied stylus pen to the grip belt.
Attaching an optional wrist strap
Attach the wrist strap to the strap mount on the grip belt,
adjust the length and fasten. You can also attach the wrist strap to the strap mount on the
grip belt to use both for extra convenience and protection.
Attaching an optional shoulder strap
Pass the ends of the shoulder strap through the strap mount on the grip belt and adjust the length ofthe strap.
7/27/2019 Canon HF G10 manual
25/184
Preparing the Camcorder
25
Wireless Controller
First, insert the supplied CR2025 lithium button battery into the wireless controller.
1 Press the tab in the direction of the arrow and pull outthe battery holder.
2 Place the lithium button battery with the + side facing
up.
3 Insert the battery holder.
To use the wireless controller
Point the wireless controller at the camcorders remote sensor when you press the buttons.
You can rotate the LCD panel 180 degrees to use the wireless controller from the front of the
camcorder.
NOTES
When the camcorder cannot be operated with the wireless controller, or when it can only beoperated at very close range, replace the battery.
The wireless controller may not work properly when the remote sensor is situated under strong lightsources or direct sunlight.
Using a Tripod
You can mount the camcorder on a tripod but do not use tripodswith mounting screws longer than 6.5 mm (0.26 in.) as this may
cause damage to the camcorder.
Tab
7/27/2019 Canon HF G10 manual
26/184
Basic Operation of the Camcorder
26
Basic Operation of the Camcorder
Using the Touch Screen
The control buttons and menu items that appear on the touch screen change dynamically depending
on the operating mode and the task you are performing. With the intuitive touch screen interface youhave all the controls at your fingertips. You can also use the supplied stylus pen for a more preciseoperation.
Touch
Press firmly on an element displayed on the touch screen.
Used to start playing back a scene in an index screen, to select
a setting from the menus, to select the subject whom thecamcorder will recognize as the main subject of the scene, etc.
Drag
While applying pressure, swipe your finger up and down or leftand right across the screen.
Used to scroll menus, to browse through index screen pages orto adjust slider controls like the volume.
IMPORTANT
The camcorder uses a pressure-sensitive touch screen. Press firmly when using touch
operations.
In the following cases, you may not be able to perform touch operations correctly.
- Using your fingernails or hard-tipped objects other than the supplied stylus pen, such as ballpointpens.
- Operating the touch screen with wet or gloved hands.
- Applying excessive force or forcefully scratching the touch screen.- Attaching commercially available screen protectors or adhesive film onto the touch screens
surface.
7/27/2019 Canon HF G10 manual
27/184
Basic Operation of the Camcorder
27
Operating Modes
Recording
In recording mode, the camcorders operating mode is determined by the position of the mode switch.
Playback
Press the camera/play buttonS to switch the camcorderbetween camera (recording) mode and playback mode. You can
pressS when the camcorder is off to turn it on directly inplayback mode.
NOTES
When switching to a playback mode, the memory selected for playback will be the same currently
used for recording. You can also press and holdB on the wireless controller for more than 2 seconds to switch
between recording and playback mode.
Operating mode Mode switch Operation
Let the camcorder take care of all the settings while you concentrate on recording(0 38). This operating mode is suitable if you just prefer not to bother withdetailed camcorder settings.
Enjoy full access to menus, settings and advanced functions (0 41).
Give your recordings a cinematic look and use cinema-look filters to create uniquemovies (0 101).
Operating mode Operation
Playing back movies (0 86).
Viewing photos (0 121).
7/27/2019 Canon HF G10 manual
28/184
Basic Operation of the Camcorder
28
Using the Menus
Many of the camcorders functions can be adjusted from the FUNC. panel and the setup menus. Fordetails about the available menu options and settings, refer to the appendix Menu Options Lists
(0 138).
FUNC. Panel
The FUNC. panel shows a convenient overview of frequently used shooting functions. Touch [FUNC.]
to access the FUNC. panel and then touch the function you want to set or adjust.You may need to drag your finger up and down the screen to find the control button of the desiredfunction. In mode, access to functions is limited.
Edit Panel
Touch [Edit] to display a panel showing available operations (copying, deleting, etc.), and then touchthe operation you want to perform.
Operating modes:
Operating modes:
Touch the controlbutton of thedesired function
FUNC. panel in mode
Edit panel in mode
Touch the control
button of thedesired operation
7/27/2019 Canon HF G10 manual
29/184
Basic Operation of the Camcorder
29
Setup Menus
* In mode setup menus cannot be accessed and most menu settings will be reset to defaultvalues.
1 or mode only: Touch [FUNC.]
2 Touch [MENU] to open the setup menus.
You can also pressu on the wireless controller.
3 Touch the tab of the desired menu.
4 Drag your finger up and down to bring the setting you
want to change into the orange selection bar.
Menu items not available appear grayed out. You can touch any menu item on the screen to bring it
directly into the selection bar.
5 When the desired menu item is inside the selection bar, touch the orange frame on the
right.
6 Touch the desired option and touch [a].
You can touch [a] to close the menu at any time.
Operating modes: *
7/27/2019 Canon HF G10 manual
30/184
First Time Settings
30
First Time Settings
Setting the Date and Time
You will need to set the date and time of the camcorder beforeyou can start using it. The [Date/Time] screen will appear
automatically when the camcorders clock is not set.
1 Pressx to turn on the camcorder.
The [Date/Time] screen appears and the year will beselected.
2 Touch a field you want to change (year, month, day, hours or minutes).
3 Touch [Z] or [O] to change the field as necessary.
4 Set the correct date and time by changing all the fields in the same way.5 Touch [Y.M.D], [M.D,Y] or [D.M.Y] to select the date format you prefer.
In some screens, only the month and day are displayed but it will still follow the order youselected.
6 Touch [24H] to use 24-hour clock or leave it unselected to use 12-hour clock (AM/PM).
7 Touch [OK] to start the clock and close the setup screen.
NOTES
You can adjust the date and time later on with the6 [Date/Time] setting.
When you do not use the camcorder for about 3 months, the built-in rechargeable lithium batterymay discharge completely and the date and time setting may be lost. In such case, recharge thebuilt-in lithium battery (0 166) and set the time zone, date and time again.
Changing the Language
The default language of the camcorder is English. You can setit to one of 27 languages.
1 Open the [Language a] screen.
[FUNC.] [MENU] 6 [Language a]
Touching [FUNC.] is necessary only when performing the procedure in a recording mode.
2 Touch the desired language and then touch [a].
NOTES
Some control buttons, such as [ZOOM], [FUNC.] or [MENU], will appear in English regardless of thelanguage selected.
Operating modes:
7/27/2019 Canon HF G10 manual
31/184
First Time Settings
31
Changing the Time Zone
Change the time zone to match your location. The default setting is New York.
1 Open the [Time Zone/DST] screen.
[FUNC.] [MENU] 6 [Time Zone/DST]
Touching [FUNC.] is necessary only when performing the procedure in a recording mode.
2 Touch [S] to set the home time zone, or [V] to set the time zone of your destination
when you are traveling.
3 Touch [Z] or [O] to set the desired time zone. If necessary, touch [U] to adjust fordaylight saving time.
4 Touch [a] to close the menu.
Operating modes:
7/27/2019 Canon HF G10 manual
32/184
Using a Memory Card
32
Using a Memory Card
Memory Cards Compatible for Use with the Camcorder
You can use the following types of commercially available Secure Digital (SD) cards with this
camcorder.As of October 2010, the movie recording function has been tested using SD/SDHC/SDXC memorycards made by Panasonic, Toshiba and SanDisk.
* When using an SD memory card without a speed class rating, you may not be able to record movies,depending on the memory card used.
**SD memory cards with a capacity of 64 MB or smaller cannot be used to record movies.
NOTES
About the Speed Class: Speed Class is a standard that indicates the minimum guaranteed datatransfer speed of memory cards. When you buy a new memory card, look for the Speed Class logo
on the package.We recommend using memory cards rated SD Speed Class 4, 6 or 10.
SDXC Memory Cards
You can use SDXC memory cards with this camcorder. When using memory cards with other devices,
such as digital recorders, computers and card readers, make sure that the external device iscompatible with SDXC cards. The table below summarizes compatibility by computer operatingsystem, as of October 2010. For the latest information, however, contact the computer, operatingsystem or memory card manufacturer.
Compatible operating systems for SDXC memory cards
IMPORTANT
If you use an SDXC memory card with a computer OS that is not SDXC-compatible, you may be
prompted to format the memory card. In such case, cancel the operation to prevent data loss.
After repeatedly recording, deleting and editing scenes (fragmented memory), it will take longer to
write data on the memory and recording may stop. Save your recordings and initialize the memoryusing the camcorder.
Memory card type: SD memory card, SDHC memory card, SDXC memory cardSD Speed Class*:
Capacity: 128 MB or larger**.
Operating system Compatibility
Windows 7 Compatible
Windows Vista Compatible (requires Service Pack 1 or later)
Windows XP Compatible (requires Service Pack 3 and KB955704 update)
Mac OS X Not compatible
7/27/2019 Canon HF G10 manual
33/184
Using a Memory Card
33
Eye-Fi Cards
This product is not guaranteed to support Eye-Fi card functions (including wireless transfer). In case ofan issue with an Eye-Fi card, please check with the card manufacturer.
Also note that an approval is required to use Eye-Fi cards in many countries or regions. Withoutapproval, use of the card is not permitted. If it is unclear whether the card has been approved for usein the area, please check with the card manufacturer.
Inserting and Removing a Memory Card
Make sure to initialize (0 36) all memory cards before using them with this camcorder.
1 Turn off the camcorder.
Make sure the ON/OFF (CHG) indicator is off.
2 Open the double memory card slot cover.
3 Insert the memory card straight, with the label facing the
front of the camcorder, all the way into one of the
memory card slots until it clicks.
You can also use two memory cards, one in each memory
card slot.
To use the wireless communication features of an Eye-Ficard, insert it into memory card slot Y. Be sure youunderstand the information provided in Eye-Fi Cards
(0 33) before using an Eye-Fi card.
4 Close the double memory card slot cover.
Do not force the cover closed if the memory card is not
correctly inserted.
To remove the memory cardPush the memory card once to release it. When the memory card springs out, pull it all the way out.
IMPORTANT
Observe the following precautions while the ACCESS indicator is flashing. Failure to do so may
result in permanent data loss.- Do not disconnect the power source or turn off the camcorder.
- Do not remove the memory card.
Turn off the camcorder before inserting or removing an memory card. Inserting or removing the
memory card with the camcorder on may result in permanent data loss.
Memory cards have front and back sides that are not interchangeable. Inserting a memory card
facing the wrong direction can cause a malfunction of the camcorder. Be sure to insert the memorycard as described in step 3.
7/27/2019 Canon HF G10 manual
34/184
7/27/2019 Canon HF G10 manual
35/184
Using a Memory Card
35
NOTES
You cannot use relay recording from the built-in memory to memory cardY. When using a single
memory card, be sure to insert it into memory card slotX. There will be a momentary stop in the scene at the point where the camcorder switches from one
memory to another.
Any of the following actions will deactivate the relay recording function:- Turning off the camcorder.- Opening the double memory card slot cover.
- Changing the position of the mode switch.- Changing the camcorders operating mode.- Changing the memory used for recording movies.
Double Slot Recording
Double slot recording allows you to record the same scene simultaneously to both memory cards. This
is a convenient way to make a backup copy of your recording while you record.
1 Insert memory cards into memory card slotX and memory card slotY.
2 Open the [Rec Media for Movies] screen.
[FUNC.] [MENU] 8 [Rec Media for Movies]
3 Activate double slot recording.
[4] [Double Slot Rec] [A]
4 Touch [a].
will appear on the screen.
NOTES
If a memory card becomes full during double slot recording, recording on both cards will stop.
If an error occurs with one of the memory cards, recording will continue on the other card.
Operating modes:
7/27/2019 Canon HF G10 manual
36/184
Using a Memory Card
36
Initializing the Memory
Initialize memory cards when you use them with this camcorder for the first time. You can also initializea memory card or the built-in memory to permanently delete all the recordings it contains.
At the time of purchase, the built-in memory comes pre-initialized and contains music files for use asbackground music and images for use with the image mix function (image mix frames).
1 Power the camcorder using the compact power adapter.
Do not disconnect the power source or turn off the camcorder until the initialization is completed.
2 Open the initialization screen for the desired memory.
[FUNC.] [MENU] 6 [Initializef/g] [f Built-in Mem.], [4 Mem. Card A] or[7 Mem. Card B] [Initialize]
Touching [FUNC.] is necessary only when performing the procedure in a recording mode. In the initialization screen, touch [Complete Initialization] to physically erase all the data rather than
just clear the file allocation table of the memory.
3 Touch [Yes].
If you selected the [Complete Initialization] option, you can touch [Cancel] to cancel theinitialization while it is in progress. All recordings will be erased and the memory can be usedwithout any problem.
4 Touch [OK] and then touch [a].
IMPORTANT
Initializing the memory will permanently erase all recordings. Lost original recordings cannot berecovered. Make sure you save important recordings in advance using an external device (0 125).
Initializing a memory card will permanently erase any music files and images you may havetransferred to the card. (The music files and image mix frames that come pre-installed in the built-in
memory will be restored after it is initialized.) To transfer music files from the supplied CamcorderSupplemental Disc to the memory card:- Windows users: Use the supplied PIXELAs software. For details, refer to the Software Guide
(PDF file) of the supplied PIXELAs software.- Mac OS users: Use Finder to transfer music files from the [MUSIC] folder on the supplied
Camcorder Supplemental Disc to the memory card. Refer toAbout the music files (0 178) for
the folder structure of the memory card. At the time of purchase, Eye-Fi cards contain the necessary network configuration software. Be
sure to install the software and complete the required configuration setup before you initialize theEye-Fi card prior to using it with this camcorder.
Operating modes:
7/27/2019 Canon HF G10 manual
37/184
Recording Movies and Photos
37
Recording
Recording Movies and PhotosBy default, movies and photos are recorded in the built-in memory. You can select the memory that will
be used to record movies and photos (0 34).Please read the IMPORTANT section (0 42) before using an Eye-Fi card.
POINTS TO CHECK
Before you begin recording, make a test recording first to check that the camcorder is operatingcorrectly.
Preparing to Record
1 Attach a charged battery pack to the camcorder
(0 20).
2 Turn on the camcorder.
3 Select the memory for recording (0 34).
To use relay recording (0 34), insert a memory card intomemory card slot X or both memory card slots.
To use double slot recording (0 35), insert memory cards
into both memory card slots.4 Remove the lens cap.
5 If you need to use the viewfinder, pull it out and, if
necessary, adjust it using the dioptric adjustment lever.
Lens cap
Viewfinder
3 Recording
7/27/2019 Canon HF G10 manual
38/184
Recording Movies and Photos
38
Recording in AUTO Mode
When you use mode to shoot video and take photos, the camcorder will automatically adjustvarious settings for you.
1 Set the mode switch to .
2 Turn on the camcorder.
To record video
Pressg to begin recording.
Pressg again to pause the recording.
The ACCESS indicator will flash from time to time while the
scene is being recorded. During recording,N will appear on the screen.
To take photos
Touch [PHOTO].
A green icon (h) will appear momentarily on the screen and the ACCESS indicator will flash as the
photo is recorded.
You can record photos simultaneously while recording a movie.
You can also pressj on the wireless controller.
When you have finished recording
1 Make sure that the ACCESS indicator is off.
2 Turn off the camcorder.
3 Close the LCD panel.
Operating modes:
[PHOTO]
7/27/2019 Canon HF G10 manual
39/184
Recording Movies and Photos
39
Rating ScenesYou can turn on the scene rating option in recording mode with the8 [Rate Scenes
(Recording)] setting. Immediately after recording a scene, you will have the option to rate it bytouching one of the rating buttons; you can also touch [ ] or [a] to leave the scene unrated.
Later you can play back scenes and perform other scene operations by rating.
You can rate scenes while the camcorder is in mode but you must change the settingdescribed above in or mode.
About AUTO mode
Only the following functions are available in mode.- Zoom (0 51).- Quick Start (0 43).
- Video snapshot (0 79).- Advanced image stabilization modes (0 54) to shoot video while walking or to stabilize theshot while zooming in on faraway subjects (telephoto).
- Face detection (0 48) to get beautiful shots of people every time, tracking the subject evenif the person moves.
- Touch & Track (0 50) to track other moving subjects, keeping them in focus and using the
best settings to record them.- Story Creator (0 98) to transform your movies into compelling video stories by following
simple scripts for various scenarios.
- Decoration (0 103) to add graphical elements using stamps, drawings, image mix andmore.
About the Smart AUTO functionIn mode, the camcorder will automatically detect certain characteristics of the subject,background, lighting conditions, etc. It will then adjust various settings (focus, exposure, color,
image stabilization, image quality, among others), selecting the best settings for the scene youwant to shoot. The Smart AUTO icon will change to one of the following icons.
7/27/2019 Canon HF G10 manual
40/184
Recording Movies and Photos
40
IMPORTANT
Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do somay result in permanent data loss or damage to the memory.
- Do not open the double memory card slot cover.- Do not disconnect the power source or turn off the camcorder.- Do not change the camcorders operating mode.
Be sure to save your recordings regularly (0 125), especially after making important recordings.Canon shall not be liable for any loss or corruption of data.
Photos recorded on an Eye-Fi card in memory card slot Y will be uploaded automatically aftersetting the camcorder to playback mode, if you are within the range of a configured network.
Always verify that Eye-Fi cards have been approved in the country/region of use. See also Using anEye-Fi Card(0 136).
Smart AUTO icons
1The icon in parentheses appears under backlight conditions.2This icon will appear under tele macro conditions. Tele macro is activated automatically when you
zoom toward the telephoto end and close in on the subject. Tele macro allows you to get closershots of small subjects and adds a soft focus to the background, so the subject not only lookslarger but also stands out more.
Background (color of the icon) Bright1
(grey)
Blue skies1
(light blue)
Vivid colors1
(green/red)
Sunsets1
(orange)Subject
People (stationary)
( ) ( ) ( )
People (moving)
( ) ( ) ( )
Subjects other than people,such as landscapes
( ) ( ) ( )
Close objects / 2
( / 2)
/ 2
( / 2)
/ 2
( / 2)
Background (color of the icon) Dark (dark blue)
Subject Spotlight Night scene
People (stationary)
People (moving)
Subjects other than people, such aslandscapes
Close objects / 2
7/27/2019 Canon HF G10 manual
41/184
Recording Movies and Photos
41
NOTES
About the power saving mode: If6 [Power Saving Mode] [Auto Power Off] is set to
[A On], the camcorder will shut off automatically to save power when it is powered by a batterypack and is left without any operation for 5 minutes. Pressx to turn on the camcorder.
When recording in bright places, it may be difficult to use the LCD screen. In such cases, you canturn on the LCD backlight (0 23) or adjust the brightness of the LCD screen with the6
[LCD Brightness] setting. Alternatively, you can also use the viewfinder (0 22).
Under certain conditions, the Smart AUTO icon that appears on the screen may not match the
actual scene. Especially when shooting against orange or blue backgrounds, the sunset or one ofthe blue skies icons may appear and the colors may not look natural. In such case, we recommendrecording in mode (0 41).
In mode, most camcorder settings will return to default values, but the following settings willbe maintained even after setting the mode switch to .
- FUNC. panel: [Zoom], [Decoration].- 7 menu: [Soft Zoom Control], [Zoom Speed Level], [Zoom Lever Zoom Speed], [Wireless
Ctrlr Zoom Speed], [AF Mode], [Auto Slow Shutter], [Conversion Lens], [Camcorder Shake
Indicator].- 8 menu: [Video Snapshot Length], [Rate Scenes (Recording)], [Rec Media for Movies],
[Recording Mode], [Rec Media for Photos], [Scan Reverse Rec].
- 6 menu: All settings.
Photos are recorded as JPG files. The photo size (1920x1080) and quality cannot be changed. At
this size, a 1 GB memory card can hold approximately 670 photos. However, the actual number ofphotos that can be recorded will vary depending on the subject and shooting conditions.
Photos cannot be recorded while the digital zoom is activated, during double slot recording or whilefading in or fading out a scene.
Recording iny (Manual) Mode
When the mode switch is set toy (Manual mode), you can enjoy full access to the menus andmanually adjust the exposure, focus, white balance and many more of the camcorders settings to
your preference. Even in mode, though, the camcorder can help you with the settings. Forexample, by using Special Scene recording programs (0 63).
1 Set the mode switch toy.
2 Turn on the camcorder.
3 Record movies and photos.
The procedure is the same as in mode (0 38).
Operating modes:
7/27/2019 Canon HF G10 manual
42/184
Recording Movies and Photos
42
Reviewing the Latest Scene Recorded
You can review the last 4 seconds of the last scene recorded with the camcorder without switching to
playback mode. While reviewing the latest scene, the picture will be played back without sound.
1 Set the mode switch toy or .
2 Review the last 4 seconds of the scene.
[FUNC.] [ Review Recording]NOTES
When double slot recording is activated, only the scene recorded on memory cardX will be played
back.
IMPORTANT
Observe the following precautions while the ACCESS indicator is on or flashing. Failing to do so
may result in permanent data loss or damage to the memory.
- Do not open the double memory card slot cover.
- Do not disconnect the power source or turn off the camcorder.
- Do not change the camcorders operating mode.
Be sure to save your recordings regularly (0 125), especially after making important recordings.
Canon shall not be liable for any loss or corruption of data.
Photos recorded on an Eye-Fi card in memory card slotY will be uploaded automatically after
setting the camcorder to playback mode, if you are within the range of a configured network.Always verify that Eye-Fi cards have been approved in the country/region of use. See also Using an
Eye-Fi Card(0 136).
NOTES
About the power saving mode: If6 [Power Saving Mode] [Auto Power Off] is set to
[A On], the camcorder will shut off automatically to save power when it is powered by a battery
pack and is left without any operation for 5 minutes. Pressx to turn on the camcorder.
When recording in bright places, it may be difficult to use the LCD screen. In such cases, you can
turn on the LCD backlight (0 23) or adjust the brightness of the LCD screen with the6
[LCD Brightness] setting. Alternatively, you can also use the viewfinder (0 22).
Operating modes:
7/27/2019 Canon HF G10 manual
43/184
Quick Start Function
43
Quick Start Function
When you close the LCD panel with the camcorder on, the camcorder enters the standby mode. In
standby mode the camcorder consumes only about 1/3 the power used when recording, savingenergy when you are using a battery pack. Additionally, when you open the LCD panel or pull out the
viewfinder, the camcorder is ready to start recording in approximately 1 second*, allowing you torecord the subject right away.* The actual time required varies depending on the shooting conditions.
1 With the camcorder on and in a recording mode, close the LCD panel.
A beep will sound and the green ON/OFF (CHG) indicator will change to orange to indicate thecamcorder entered standby mode.
When using only the viewfinder (with the LCD panel closed), you can return the viewfinder to itsretracted position to set the camcorder in standby mode.
2 When you wish to resume recording, open the LCD panel.
The ON/OFF (CHG) indicator turns back green and the camcorder is ready to record.
You can also pull out the viewfinder to start recording with the LCD panel closed.
IMPORTANT
Do not disconnect the power source during standby mode (while the ON/OFF (CHG) indicator is lit
in orange).
NOTES
The camcorder will not enter standby mode while the ACCESS indicator is on or flashing, while a
menu is being displayed or while using the viewfinder. The camcorder may also not enter standbymode when the battery charge is too low. Check that the ON/OFF (CHG) indicator changes toorange.
About standby mode and auto power off:
- The camcorder will power off automatically if left in standby mode for 10 minutes. Pressx
to turn on the camcorder.- You can select the length of time until shut-off or turn off the Quick Start function altogether with
the6 [Power Saving Mode] [Quick Start (Standby)] setting.
- The usual 5-minute auto power off setting of [Power Saving Mode] is not applicable while thecamcorder is in standby mode.
Changing the position of the mode switch while the camcorder is in standby mode will reactivate thecamcorder in the operating mode selected.
Operating modes:
7/27/2019 Canon HF G10 manual
44/184
Selecting the Video Quality (Recording Mode)
44
Selecting the Video Quality (Recording Mode)
The camcorder offers 5 recording modes. Changing the recording mode will change the recording
time available on the memory. Select MXP or FXP mode for better movie quality; select LP mode forlonger recording times. The following table gives approximate recording times.
1 Open the [Recording Mode] screen.
[FUNC.] [MENU] 8 [Recording Mode]
2 Touch the desired recording mode and then touch [a].
NOTES
Movies recorded in MXP mode cannot be saved on AVCHD discs. Use an external Blu-ray Disc
recorder to copy MXP movies onto Blu-ray discs or use the supplied softwareVideoBrowsertocreate AVCHD discs*.
The camcorder uses a variable bit rate (VBR) to encode video so the actual recording times will varydepending on the content of the scenes.
The camcorder retains the last setting used even if you set the camcorder to mode.
* MXP scenes will be converted to an image quality similar to that of FXP scenes.
Operating modes:
Approximate recording times Default value
1 Recorded in 1,920 x 1,080 resolution. Movies recorded using other recording modes are recordedin 1,440 x 1,080 resolution.
2At the time of purchase, the built-in memory contains about 70 MB of music files (backgroundmusic) and 5 MB of image files (image mix frames).
3A single scene can be recorded continuously for 12 hours; at that point, the camcorder will stopfor about 3 seconds before resuming recording.
Recording mode
MXP1 FXP1 XP+ SP LPMemory
4 GB Memory card 20 min. 30 min. 40 min. 1 hr. 10 min. 1 hr. 30 min.
8 GB Memory card 40 min. 1 hr. 1 hr. 25 min. 2 hr. 20 min. 3 hr.
16 GB Memory card 1 hr. 25 min. 2 hr. 5 min. 2 hr. 50 min. 4 hr. 45 min. 6 hr. 5 min.
32 GB Memory card/Built-in memory2
2 hr. 55 min. 4 hr. 10 min. 5 hr. 45 min. 9 hr. 35 min. 12 hr. 15 min.3
64 GB Memory card 5 hr. 55 min. 8 hr. 20 min. 11 hr. 30 min. 19 hr. 10 min.3 24 hr. 30 min.3
7/27/2019 Canon HF G10 manual
45/184
Selecting the Frame Rate
45
Selecting the Frame Rate
You can change the frame rate (the number of frames recorded per second) to change the look of your
movies.
1 Open the [Frame Rate] screen.
[FUNC.] [MENU] 8 [Frame Rate]
2 Touch the desired frame rate and then touch [a].
Options
* Recorded as 60i.
NOTES
Movies recorded with the [ 24P] frame rate cannot be converted to standard definition using thecamcorder. If you want to upload your movies to video sharing Web sites, set the frame rate to
[E PF24] or convert the movies to standard definition using the supplied softwareVideoBrowser.
Operating modes:
[C 60i (Standard)] 60 fields per second, interlaced. Standard frame rate of NTSC analog TVsignals.
[o PF30] Shooting at 30 frames per second, progressive*. Use this frame rate to easily edit yourrecordings, for example, to post them on the Web.
[E PF24] Shooting at 24 frames per second, progressive*. Using this frame rate will give yourrecordings a cinematic look. Recording in mode will further enhance the effect.
[ 24P] 24 frames per second, progressive. Using this frame rate will achieve the same cinematiclook as [E PF24], the difference being that video is recorded as true 24p.
7/27/2019 Canon HF G10 manual
46/184
Focus Adjustment
46
Focus Adjustment
You can adjust the focus manually and use the peaking function to assist you or you can let the
camcorder focus for you by using autofocus. With autofocus, you can set the autofocus speed.The camcorder also features two more focusing functions, face detection and Touch & Track.
POINTS TO CHECK
Adjust the zoom before you start the procedure.
Manual Focus
Use the focus ring to focus manually. You can also use peaking to help you focus more accurately.
1 Open the focus controls.
[FUNC.] [X Focus]
To switch to autofocus without opening the focus controls, press . In such case, Touch AF(step 3) will not be available.
2 Touch [MF].
3 Touch a subject that appears inside theX frame.
The Touch AF mark (P) will flash and the focusing distance will be adjusted automatically. You
have the option to further adjust the focus manually as necessary.
4 Turn the focus ring to adjust the focus. The center of the screen will be magnified to help you focus more easily. You can also turn off this
function with the7 [Focus Assistance] setting.
The focusing distance displayed will change as you adjust the focus. You can change the unitsused for the distance display with the6 [Distance Units] setting.
You can use the6 [Focus Ring Response] setting to adjust the sensitivity of the focusring.
You can use the6 [Focus Ring Direction] setting to select which direction to turn thefocus ring.
Focus PresetWhen focusing manually, you can set a preset position for the focus in advance so that you can laterreturn to that preset focus position instantly.
1 Open the focus controls.
[FUNC.] [X Focus]
2 Touch [MF].
3 Turn the focus ring to the desired focus position.
4 Touch [ ] to set the preset focus position.
Operating modes:
7/27/2019 Canon HF G10 manual
47/184
Focus Adjustment
47
5 After adjusting the focus, touch [ ] to return to the preset focus position.
Touch [ ] again to cancel the current preset focus position.
[ ] will be grayed out while adjusting the focus or zoom.
You can use the6 [Focus Preset Speed] setting to adjust the speed at which thecamcorder returns to the preset focus position.
NOTES
The preset focus position will be canceled when the camcorder is turned off.
When the camcorder is in mode, the focus preset function cannot be used.
Peaking
When peaking is activated, edges in focus on the screen will be highlighted in red, blue or yellow. In
addition, you can choose to switch the screen to black & white, further emphasizing the edges.1 Open the focus controls.
[FUNC.] [X Focus]
2 Touch [5].
For the black & white setting: Touch [Off] or [On]
For the peaking color: Touch [Red], [Blue] or [Yellow]
3 Touch [f].
4 Touch [d].
Peaking is activated and edges are highlighted. You can turn the focus ring on this screen or
touch [a] to hide the focus controls. The peaking effect and black & white picture will not appear in your recordings.
Autofocus
When autofocus is activated, the camcorder continuously adjusts the focus on the subject in thecenter of the screen. The focusing range is 2 cm (0.8 in.; at full wide-angle, measured from the front of
the lens barrel) tof and 60 cm (2 ft.; throughout the zoom range, measured from the front of the lensbarrel) tof. Perform the following procedure to set the autofocus speed.
1 Open the [AF Mode] screen.[FUNC.] [MENU] 7 [AF Mode]
2 Touch the desired option and then touch [a].
The icon of the selected option appears on the screen.
Options ( Default value)
[R Instant AF] Sets the autofocus to Instant AF. The focus is adjusted at the highest speed. Thismode is useful even when recording in very bright or low-light surroundings. This mode uses both the
TTL system and external sensor for focusing.
[ Medium AF] Sets the autofocus to Medium AF. The camcorder focuses more smoothly on thesubject than when using the [R Instant AF] setting. This mode uses both the TTL system andexternal sensor for focusing.
[S Normal AF] Sets the autofocus to Normal AF. The autofocus adjustment is made at a stablespeed.
7/27/2019 Canon HF G10 manual
48/184
Focus Adjustment
48
NOTES
While using autofocus, you can turn the manual ring to focus manually. When you stop turning the
ring, the camcorder returns to autofocus. This is useful in situations such as when focusing on asubject on the other side of a window.
When recording in bright surroundings, the camcorder closes down the aperture. This may causethe picture to appear blurred and is more noticeable toward the wide angle end of the zoom range.
In such case, set7 [ND Filter] to [O Automatic].
When you set7 [Conversion Lens] to a setting other than [B Off], the [ Instant AF]
and [ Medium AF] settings are not available.
Autofocus takes longer to focus when the frame rate is set to [o PF30], [E PF24] or
[ 24P] than when it is set to [C 60i (Standard)].
When recording under dark conditions, the focusing range narrows and the picture may appear
blurred. Autofocus may not work well on the following subjects or in the following cases. In such case, focus
manually.- Reflective surfaces- Subjects with low contrast or without vertical lines
- Fast moving subjects- Through dirty or wet windows- Night scenes
Face Detection
The camcorder automatically detects peoples faces and uses this information to select the optimal
focus and exposure settings.
* Face detection is always activated in mode.
POINTS TO CHECK
Select a recording program other than [q Night Scene], [p Low Light], [M Fireworks] or[y Manual Exposure].
By default, face detection is activated. If the function was turned off, perform the following procedureto turn it on.
1 Open the [Face Detection & Tracking] screen.
[FUNC.] [MENU] 7 [Face Detection & Tracking]
2 Touch [A Ono] and then touch [a].
Operating modes: *
7/27/2019 Canon HF G10 manual
49/184
Focus Adjustment
49
To select the main subjectIf there is more than one person in the picture, the camcorder will automatically select one person it
determines is the main subject. The main subject is indicated by a white face detection frame and the
camcorder will optimize the settings for that person. Other faces will have gray frames.
Touch a different face on the touch screen to optimize the
camcorders settings for that person using the Touch & Track
function.
Limiting Autofocus to Faces
While using autofocus, you can limit the autofocus function only to cases when a subjects face isdetected and use manual focus for all other scenes. The camcorder will also adjust the brightness
when focusing automatically on the subjects face.
Set assignable button 2 to [ Face Only AF] (0 84) and press the button.
appears on the screen.
NOTES
The camcorder may mistakenly detect the faces of non-human subjects. In such case, turn facedetection off.
In certain cases, faces may not be detected correctly. Typical examples include:- Faces extremely small, large, dark or bright in relation to the overall picture.
- Faces turned to the side, at a diagonal or partially hidden.
Face detection cannot be used in the following cases.
- When the shutter speed used is slower than 1/30 (1/24 if the frame rate is set to [E PF24] or[ 24P].
- When the digital zoom is activated at more than 40x zoom (dark blue area on the zoom bar).
- When8 [Scan Reverse Rec] is set to an option other than [B Off].
When face detection is activated, the slowest shutter speed used by the camcorder is 1/30 (1/24 if
the frame rate is set to [E PF24] or [ 24P]).
Main subject
7/27/2019 Canon HF G10 manual
50/184
Focus Adjustment
50
Touch & Track
When recording a group of people using face detection, the camcorder will automatically detect oneperson as the main subject. You can use Touch & Track to tell the camcorder to track and optimize
settings for a different person. You can also use Touch & Track to always keep in focus other movingsubjects, such as pets or moving vehicles.
1 Make sure face detection (0 48) and autofocus (0 47) are activated.
Face detection is always activated in mode.
2 Point the camcorder at a moving subject and touch the subject on the touch screen.
A white double frame will appear around the subject and track it as it moves.
Touch [Cancelz] to remove the frame and cancel the tracking.
NOTES
Touching somewhere with a color or pattern unique to the subject will make it easier to track.However, if there is another subject in the vicinity that shares similar characteristics to the selected
subject, the camcorder may start tracking the incorrect subject. Touch the screen again to selectthe desired subject.
In certain cases, Touch & Track may not be able to track the subject. Typical examples include:- Subjects extremely small or large in relation to the overall picture.- Subjects too similar to the background.
- Subjects lacking sufficient contrast.
- Fast moving subjects.- When shooting indoors with insufficient lighting.
Operating modes:
7/27/2019 Canon HF G10 manual
51/184
Zooming
51
Zooming
There are three ways you can zoom in and out: using the zoom lever on the camcorder, using thezoom buttons on the wireless controller or using the zoom controls on the touch screen.In addition to the 10x optical zoom, in mode, you can turn on the digital zoom* (40x or 200x)
with the7 [Digital Zoom] setting.This camcorder also features a digital tele-converter, which allows you to enlarge the image on thescreen digitally.* Digital zoom is not available in and modes.
Using the Zoom Lever or Wireless Controller
Move the zoom lever towardQ (wide angle) to zoom out.Move it toward P (telephoto) to zoom in.
By default, the zoom lever operates at a variable speed
press gently for a slow zoom; press harder for faster zooms.
You can also use the zoom buttons on the wireless controller.
Setting the Zoom Speed
You can set the zoom speed for the zoom lever and wireless
controller.
To set the zoom lever's zoom speedFor the zoom lever, first set the overall zoom speed to one of
three levels. Next, select whether the zoom lever operates at avariable or constant speed. Refer to the following table for asummary of the zoom speed.
1 Open the zoom speed level screen.
[FUNC.] [MENU] 7 [Zoom Speed Level]
2 Touch [J Fast], [K Normal] or [L Slow] and then touch [f].
3 Touch [Zoom Lever Zoom Speed].4 Touch [I] for variable speed or [ ] for constant speed.
If you selected [ ], touch [ ] or [ ] or drag your finger along the bar to select a constant
speed.
5 Touch [a].
Operating modes:
WZoom out T Zoom in
7/27/2019 Canon HF G10 manual
52/184
Zooming
52
Approximate zoom speeds* (zoom lever)
* Measured from full wide-angle to full telephoto.**When the zoom speed is too fast (approximately 2 seconds end-to-end), the camcorder will have more
trouble focusing automatically while zooming.
To set the wireless controller's zoom speed
For the wireless controller, first set the overall zoom speed to one of three levels. The wirelesscontroller operates at a constant speed so select the speed. Refer to the following table for a summaryof the zoom speed.
1 Open the zoom speed level screen.
[FUNC.] [MENU] 7 [Zoom Speed Level]
2 Touch [J Fast], [K Normal] or [L Slow] and then touch [f].
3 Touch [Wireless Ctrlr Zoom Speed].
4 Touch [ ] or [ ] or drag your finger along the bar to select a constant speed.
5 Touch [a].
Approximate zoom speeds* (wireless controller)
* Measured from full wide-angle to full telephoto.**When the zoom speed is too fast (approximately 2 seconds end-to-end), the camcorder will have more
trouble focusing automatically while zooming.
Using the Touch Screens Zoom Controls
1 Display the zoom controls on the touch screen.
[FUNC.] [ZOOM]
The zoom controls appear on the left side of the screen.
2 Touch the zoom controls to operate the zoom.
Touch anywhere within theQ area to zoom out or
anywhere within theP area to zoom in. Touch closer to the
center for a slow zoom; touch closer to the e/d icons forfaster zooms.
3 Touch [a] to hide the zoom controls.
[Zoom Lever
Zoom Speed]
setting
Selected
constant speed
[Zoom Speed Level] setting
[L Slow] [K Normal] [J Fast]
[I] (variable) 4 sec. to 4 min. 45 sec. 3 sec. to 3 min. 2 sec.** to 1 min.
[ ] (constant) 1 (slowest) 4 min. 45 sec. 3 min. 1 min.
16 (fastest) 4 sec. 3 sec. 2 sec.**
[Wireless Ctrlr
Zoom Speed] speed
setting
[Zoom Speed Level] setting
[L Slow] [K Normal] [J Fast]
1 (slowest) 4 min. 45 sec. 3 min. 1 min.
16 (fastest) 4 sec. 3 sec. 2 sec.**
7/27/2019 Canon HF G10 manual
53/184
Zooming
53
Soft Zoom Control
Soft zoom control allows you to start and/or stop the zoom gradually.
1 Open the soft zoom control screen.[FUNC.] [MENU] 7 [Soft Zoom Control]
2 Touch the desired option and then touch [f].
Options ( Default value)
Digital Tele-Converter
Using the digital tele-converter, you can digitally increase the focal length of the camcorder by a factorof approx. 2 and record the enlarged image at full HD resolution.
1 Open the [Digital Zoom] screen.
[FUNC.] [MENU] 7 [Digital Zoom]
2 Touch [ Digital Tele-conv.] and then touch [a].
3 Open the zoom controls.[FUNC.] [ZOOM]
4 Touch [ ] (digital tele-converter) and then touch [a].
Touch [ ] again before closing the screen to deactivate the digital tele-converter.
The center of the screen will be enlarged approximately 2 times and the icon will appear.
NOTES
You can attach the optional tele-converter and use it in conjunction with this function to increase theeffect.
The digital tele-converter cannot be turned on while recording.
The image is digitally processed so the image will deteriorate throughout the zoom range.
[B Off] Use this setting if you do not intend to use soft zoom control.
[ Start] Zoom starts gradually.
[ Stop] Zoom stops gradually.
[ Start & Stop] Zoom start and stops gradually.
Operating modes:
7/27/2019 Canon HF G10 manual
54/184
Advanced Image Stabilization
54
Advanced Image Stabilization
The image stabilizer reduces camcorder blur (blur due to the camcorder moving) so you can get nice,
stable shots. Select the image stabilization mode according to the shooting conditions.
1 Open the image stabilizer screen.
[FUNC.] [Image Stabilizer]
2 Touch the desired IS mode and then touch [a].
Options ( Default value)
NOTES
If the degree of camcorder shake is too high, the image stabilizer may not be able to fully
compensate.
For surveying and following shots, when you pan the camcorder from side to side or tilt it up and
down, we recommend setting [Image Stabilizer] to [ Dynamic] or [ Standard].
Operating modes:
[ Dynamic] Compensates for a higher degree of camcorder shake, such as when shootingwhile walking, and is more effective as the zoom approaches full wide angle.
[ Standard] Compensates for a lower degree of camcorder shake, such as when shooting whileremaining stationary, and is suitable for shooting natural-looking scenes. Use this setting when
recording movies with the optional wide-converter or tele-converter.
[ Off] Use this setting when the camcorder is mounted on a tripod.
Powered ISYou can use Powered IS to make the image stabilization even more powerful. Powered IS is most
effective when you are stationary and zooming in on far subjects using high zoom ratios (the moreyou approach the telephoto end). Holding the LCD panel with your left hand will add to the stabilityof the shot.
By default, Powered IS is assigned to assignable button 2.
Press and holdY as long as you want to activatePowered IS.
appears in yellow, while Powered IS is activated. Thedegree of camcorder shake will be indicated by the icon itself( - ), but you can turn off this indication with the7
[Camcorder Shake Indicator] setting.
You can change the operation of theY button (long
press or toggle on/off) with the6 [POWERED IS Button] setting. Powered IS is available even when [Image Stabilizer] is set to [ Off].
Operating modes:
7/27/2019 Canon HF G10 manual
55/184
Automatic Gain Control (AGC) Limit
55
Automatic Gain Control (AGC) Limit
When recording in dark surroundings, the camcorder will autom