Embed Size (px)
Citation preview
LUG TYPE BUTTERFLY VALVE SERIES ACL-150(PINLESS TYPE)
CAST IRON BODY WITH CF8 DISC
The new body neck with octagon shape design offers esthetic appearance, strength and compatible flange connection to international standards. Its top flange is designed to ISO5211 for the direct mounting of gear operator or actuators which eliminate the cost of mounting bracket. The one piece design body provides outstanding protection against particle entrapment and bacterial growth. The Lug style design allows the valve to be installed between two flanges by using a separate set of bolts on each side of flange.The body is epoxy coated for better resistant against abrasion and corrosion. AUTOMA offers various materials for the valves seat and disc to meet the various requirements of customers. The fine finishing of seat surfaces and the polished edge of disc give good sealing and reduction in operating torque. The upper and lower shafts are well supported and properly sealed to prevent leakage. This pin less design has eliminated the potential of leak through pin hole.
Certificate Number : 8711
Your Partner In Flow Management
Technical Data
Note : Cv = US Gallon per minutes
SIZES
3.8161 80
4.24.79.0
10.914.218.226.840.0
8995114127139175203242
175181200213226260292337
64.578.8
123.3
202.5
301.6
DNB C
In.Cv
WT.A
(KG)
6580
100125150200
300
68
10250
345
12
50 2 52.9
2 1/2
a°
45.00
ØD2ØD1 ØE1
50
5050707070
102102102
ØE3
65
6565909090
125125125
ØE4
35
3535555555707070
350400450
141618
500600
2024
368400422480562
267297315348444
333.5389.6440.5491.6592.5 9.00
102140140140165
125
175175
175
210
70100100100130
N x M
14
1522375894
174286429550755
101213502111
31
5587
140224328572837124115642087268133504907
56.098.0
122.0202.0270.0
42.0
44.745.252.154.455.860.665.676.975.085.7
104.6130.3151.4
4 x 5/8"-11
104.3
156.0
250.8
120.6
139.7152.4190.5215.9241.3298.4361.9
476.2539.7
431.8
577.9635.0749.3
n x ØE2
4 x Ø7
Dimension in mm(ANSI 150)
22.50
15.00
11.25
4567
910
8
SEAT
LOCK PIN
BUSHING
BUSHING
1
1
1
2
1
PTFE
1ALUMINIUMRIVET
NAMEPLATE2
SUS 416PTFE
UPPER STEM SUS 416SPRING STEEL
112
11121314
HALF RINGRETAINER RING
2
15 LOCKABLE HANDLE 1 CARBON STEEL C/W EPOXY COATING
EPDM
EPDM
16171819
INDICATOR 1 CARBON STEEL C/W EPOXY COATING
HEX BOLT
2
SUS 304WASHER
2
2
HEX NUT SUS 304SUS 304
2 SUS 304
SPRING WASHER
20
SPRING STEEL
32
LOWER STEM11 SUS 416
DISC CF81
PART QTY. MATERIALBODY 1
No.
CAST IRON
Material
`O´ RING
`O´ RING
ALUMINIUM
45.00
22.5022.5022.50
15.00
11.25
9.00
Working Temperature
-10 ~ 80 -15 ~ 140 -20 ~ 150 -20 ~ 180 -50 ~ 200
NBR EPDM VITON PTFE SILICONE
Temperature °C
Seat Material
EPDM
4 x Ø74 x Ø7
4 x Ø104 x Ø104 x Ø104 x Ø124 x Ø124 x Ø124 x Ø124 x Ø184 x Ø184 x Ø184 x Ø23
4 x 5/8"-114 x 5/8"-118 x 5/8"-118 x 3/4"-108 x 3/4"-108 x 3/4"-1012 x 7/8"-912 x 7/8"-912 x 1"-816 x 1"-8
16 x 1 1/8"-720 x 1 1/8"-720 x 1 1/4"-7
15.00
45.00
Standard: Design Standard : BS EN593
Face to Face : BS EN558-1Flange : ANSI B16 125/150Top Flange : ISO 5211Test Inspection : BS EN 12266-1 / API 598
Pressure Test
2” - 12” Μ14"
1.6 MPa 1.0 MPa
Seal 1.76 / 17.6 1.1 / 11
Body 2.4 / 24 1.5 / 15
SIZE
Working Pressure
Hydrostatic Test
Mpa / bar
(UNC-2B)* TORQUE (Nm)
PN 1615
PN 10PTFE
1723
4062
102192323490625
18
20294875
122226372558715
8469821316 1131
1431175523012744
IF PTFE SEAT ONLY WITH PN10
PTFE TEMPERATURE DEPEND ON THE LINED RUBBER
* Torque PTFE / Torque PN10&16 for Rubber Seat
©2014 Automa Valve ACL-150 08/14
The contents of this literature for informative purposes only. Automa is not responsible for suitability or compatibility of these products in relation to system requirement. For specific requirements, consult Automa or its distributors. Automa reserves the right to change or modify product design without prior notice.
TTS Valve Technologies Sdn. Bhd.(A Member Company of Unimech Group Berhad)
24 Jalan TS 6/9, Taman Industri Subang. 47510 Subang Jaya. Selangor Darul Ehsan. MALAYSIA
Tel : +60356218811 Fax : +60356213278
Email : [email protected] Website : www.ttsvalve.com.my
