Cat-x024 Cooking-hood 5 2012

Engineered for safety, performance, eciency and code compliance

COOKING HOOD COMPONENTS

DESCRIPTION PAGE

AACCESS DOORS CURVED U.L. FIRE RATED D16 - D18 FLAT U.L. FIRE RATED D19, D20 HI-TEMP ACCESS DOORS D21

BBRITE GARD CLEANING PRODUCTS STAINLESS STEEL CLEANER D24 ALL PURPOSE WIPERS D24

CCAP STRIP D22CAULKING GUN D23

DDAMPERS D21DIVIDER BAR D22DRAIN, CANOPY HOOD D22DUCT TAPE D23

FFILTERS TYPE I - STANDARD D1, D5, D6 TYPE I - SPARK ARRESTOR D1, D5, D6 TYPE I - McDONALDS D1, D5, D6 TYPE II - HEAVY-DUTY STAINLESS STEEL D2, D6, D7 TYPE III - STAINLESS STEEL D2, D8 TYPE III - ALUMINUM D3, D8 TYPE III - GALVANIZED D3, D8 TYPE IV - 20mm STAINLESS STEEL D3, D9 TYPE V - STAINLESS STEEL BRIGHT FINISH D4, D9, D10 TYPE V - ALUMINUM D4, D9, D10 TYPE V - GALVANIZED D4, D9, D10 MESH AIR TYPE D10FOIL TAPE D23

GGASKET REPAIR KIT D15GREASE CUPS D22GREASE FILTERS D1 - D10

HHOOD DRAIN D22HANDLES, FILTER LOCKING D1 - D4, D9 SNAP-ON D10

DESCRIPTION PAGE

IINSULATION HANGERS D23INSULATION WELD PINS D23

LLIGHTING FIXTURES E-Z MOUNT CANOPY HOOD D11, D12 RECESSED INCANDESCENT D13 RECESSED FLUORESCENT D13 REPLACEMENT PARTS, L55 D12

MMOULDINGS D22

OORDER FORMS CURVED ACCESS DOOR D17, D18 FLAT ACCESS DOOR D20

QQUICK-TITE FITTINGS D14 HOLE PLUGS D14 ASSEMBLY BREAKDOWN D15

SSEALANT, SILICONE D23STAINLESS STEEL CLEANER D24

TTAPE, FOIL & DUCT D23

WWELD PINS, INSULATION D23WELD STUDS, KEYHOLE D23WIPERS D24WIRE GUARDS D12

All photographs and illustrations are considered to be a representation of the actual item. In some cases there may be slight variations. This catalog, copy, part numbers and unique method of illustrating products is copyrighted by Component Hardware Group, Inc. All rights reserved.

No portion of this catalog may be reproduced in any form or by any means in whole or in part, without the written consent of Component Hardware. Component Hardware reserves the right to make any and all changes and to discontinue any of its products without notice.

Not responsible for typographical errors.

COPYRIGHT 2011 COMPONENT HARDWARE GROUP, INC.#CAT-X024 6/2011 PRINTED IN U.S.A.

Alphabetical Index

Member Organizations

Component Hardware Group is a proud member of the following organizations

Products shown in this catalog may be listed and/or certified by one or more of the following regulatory agencies and will be designated by the following marks

C USNSF 61/9UP CODE

COMPONENT

C US

FMAPPROVED

D1800-526-3694

TYPE I - sTandard fIxEd & sPark arrEsTorSTANDARD WITH SPARK ARRESTOR NOMINAL SIZE ACTUAL DIM.S WT. PER FILTER CASE

MODEL NO. MODEL NO. H &Winches & mmH X W X D

inches LbS KG QTY

101016 151016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 7.4 3.36 6

101020 151020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 9.1 4.13 6

101216 151216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 8.4 3.81 6

101218 151218 12 x 18 (305mm x 457mm) 11-1/2 x 17-1/2 x 1-3/4 9.3 4.22 6

101220 151220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-3/4 10.1 4.58 6

101224 151224 12 x 24 (305mm x 610mm) 11-1/2 x 23-1/2 x 1-3/4 12.75 5.78 3

101616 151616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-3/4 10 4.54 3

101620 151620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-3/4 12.65 5.74 3

101625 151625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 16 7.26 3

102010 152010 20 x 10 (508mm x 254mm) 19-1/2 x 9-1/2 x 1-3/4 9.4 4.26 6

102016 152016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 12.65 5.74 3

102020 152020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-3/4 15 6.8 3

102025 152025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-3/4 17.9 8.12 3

102516 152516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 14.55 6.6 3

102520 152520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-3/4 18.2 8.26 3

ALL FILTERS ARE AVAILABLE WITH SPECIAL FILTER LOCKING HANDLES. WHEN ORDERING FILTER LOCKING HANDLES, ADD SUFFIXMH TO MODEL NUMBER.

TYPE 1 WITH sPark arrEsTor aVaILaBLE. MEETs CrITErIa sET BY nfPa #96 for

CookInG WITH soLId fUEL

TYPE I - McdonaLdsNOMINAL SIZE ACTUAL DIM.S WT. PER FILTER CASE

MODEL NO. H X W inches & mmH X W X D

inches LbS KG QTY

MCD 116 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 7.4 3.36 6

MCD 116-1.5 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-1/2 7.2 3.27 6

MCD 120 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 9.1 4.13 6

MCD 120-1.5 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-1/2 8.9 4.04 6

MCD 123 12 x 24 (305mm x 607mm) 11-1/2 x 23-1/2 x 1-3/4 13 5.9 3

MCD 126 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 8.4 3.81 6

MCD 128 12 x 18 (305mm x 457mm) 11-1/2 x 17-1/2 x 1-3/4 9.3 4.22 6

MCD 133 13-1/2 x 23-13/16 (343mm x 605mm) 13 x 23-1/2 x 1-3/4 13 5.9 3

MCD 136 13-1/2 x 16 (343mm x 406mm) 13 x 15-1/2 x 1-3/4 10 4.54 3

MCD 139 13-1/2 x 19-1/2 (343mm x 495mm) 13 x 19 x 1-3/4 12 5.44 3

TYPE I - Baffle Grease Filters

C USLISTED

File No. R10173NFPA #96

C USLISTED


FILTERS AVAILABLE WITH HOOK FOR USE IN CAPTIvE-AIRE STylE HooDS. TO ORDERAdd suFFIx (-H) TO THE MODEL NUMBER.

D2 www.flamegardusa.com

TYPE II - HEaVY dUTY sTaInLEss sTEEL

HEAVY DUTY STAINLESS STEEL NOMINAL SIZE ACTUAL DIM.S WT. PER FILTER CASE

MODEL NO. H X Winches & mmH X W X D

inches LbS KG QTY

201016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-7/8 5.5 2.49 6

201020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-7/8 6 2.72 6

201216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-7/8 6.5 2.95 6

201220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-7/8 7 3.18 6

201616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-7/8 8 3.63 3

201620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-7/8 8.5 3.86 3

201625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-7/8 10.5 4.76 3

202016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-7/8 6.5 2.95 3

202020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-7/8 10.25 4.65 3

202025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-7/8 12 5.44 3

202516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-7/8 11.5 5.22 3

202520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-7/8 12 5.44 4

TYPE II & TYPE III - Baffle Grease Filters

TYPE III - sTaInLEss sTEEL

STAINLESS STEEL NOMINAL SIZE ACTUAL DIM.S WT. PER FILTER CASE


inches LbS KG QTY

301016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-5/8 4.33 1.96 3

301020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-5/8 4.06 1.84 16

301216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-5/8 4 1.81 12

301220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-5/8 4.92 2.23 12

301616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-5/8 5.38 2.44 8

301620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-5/8 6.5 2.95 8

301625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-5/8 8 3.63 4

301818 18 x 18 (457mm x 457mm) 17-1/2 x 17-1/2 x 1-5/8 6.5 2.95 8

302016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-5/8 6.5 2.95 8

302020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-5/8 7.75 3.52 8

302025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-5/8 9.5 4.31 4

302516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-5/8 8 3.63 4

302520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-5/8 9.75 4.42 4

REPLACEMENT BAIL HANDLES: TYPE III - MODEL NO. 300001ALL FILTERS ARE AVAILABLE WITH SPECIAL FILTER LOCKING HANDLES.

WHEN ORDERING FILTER LOCKING HANDLES, ADD SUFFIXMH TO MODEL NUMBER.

C USLISTED


C USLISTED


NSFCOMPONENT


D3800-526-3694

TYPE III - aLUMInUM & GaLVanIZEd

ALUMINUM WT. PER FILTER GALVANIZEDWT. PER FILTER NOMINAL SIZE ACTUAL DIM.S CASE

MODEL NO. LbS KG MODEL NO. LbS KG H X Winches & mmH X W X D

inches QTY

551016 2 .91 451016 3.36 1.52 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-5/8 8

551020 2.06 .93 451020 4.5 2.04 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-5/8 16

551216 2.35 1.06 451216 4 1.81 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-5/8 6

551220 2.5 1.13 451220 5 2.27 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-5/8 12

551616 2.75 1.25 451616 5.63 2.55 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-5/8 8

551620 3 1.36 451620 6.88 3.12 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-5/8 8

551625 5 2.27 451625 9 4.08 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-5/8 3

552016 3.7 1.68 452016 6.5 2.95 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-5/8 3

552020 3.55 1.61 452020 7.88 3.57 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-5/8 3

552025 5.7 2.59 452025 9.90 4.49 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-5/8 3

552516 4 1.81 452516 8.5 3.86 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-5/8 4

552520 5.7 2.59 452520 9.7 4.40 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-5/8 3

TYPE III & TYPE IV- Aluminum, Galvanized & 20mm Baffle Grease Filters

TYPE IV - 20mm sTaInLEss sTEEL

STAINLESS STEEL DIMENSIONS THICKNESS WT. PER FILTER CASE

MODEL NO. WIDTH x HEIGHT(mm) (mm) LbS KG QTY

FG20-500500 500 x 500 20 3.9 1.8 6

FG20-500400 500 x 400 20 4.1 1.9 6

FG20-400400 400 x 400 20 4.9 2.2 6

FG20-400500 400 x 500 20 5.8 2.6 6

FG20-500300 500 x 300 20 4.1 1.9 6

FG20-300500 300 x 500 20 4.8 2.1 6

FG20-495495 495 x 495 20 6.1 2.8 6

REPLACEMENT BAIL HANDLES: TYPE III - MODEL NO. 300001 ALL FILTERS ARE AVAILABLE WITH SPECIAL FILTER LOCKING HANDLES.

WHEN ORDERING FILTER LOCKING HANDLES, ADD SUFFIXMH TO MODEL NUMBER.

C USLISTED




TYPE V - s/s, Aluminum & Galvanized Baffle Grease Filters

TYPE V - s/s BrIGHT fInIsH

STAINLESS STEEL FINISH NOMINAL SIZE ACTUAL DIM.S WT. PER FILTER CASE


inches LbS KG QTY

FS50-1016-BA 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 4.33 1.96 12

FS50-1216-BA 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 4.06 1.84 12

FS50-1616-BA 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-3/4 4 1.81 6

FS50-2016-BA 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 4.92 2.23 6

FS50-1020-BA 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 5.38 2.44 12

FS50-1220-BA 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-3/4 6.5 2.95 12

FS50-1620-BA 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-3/4 8 3.63 6

FS50-2020-BA 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-3/4 6.5 2.95 6

FS50-2520-BA 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-3/4 6.5 2.95 6

FS50-1625-BA 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 7.75 3.52 6

FS50-2516-BA 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 9.5 4.31 6

FS50-2025-BA 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-3/4 8 3.63 6

TYPE V - aLUMInUM & GaLVanIZEd

ALUMINUM WT. PER FILTER GALVANIZEDWT. PER FILTER NOMINAL SIZE ACTUAL DIM.S CASE

MODEL NO. LbS KG MODEL NO. LbS KG H X Winches & mmH X W X D

inches QTY

FA30-1016-HD 1.47 .67 FG35-1016-HD 2.62 1.19 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 12



FA30-2016-HD 2.6 1.18 FG35-2016-HD 4.9 2.22 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 6






FA30-1625-HD 3.37 1.53 FG35-1625-HD 6 2.72 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 6

FG35-2516-HD 6 2.72 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 6


C USLISTED


C USLISTED


NSFCOMPONENT

NSFCOMPONENT

TYPE V REPLACEMENT LOCKING HANDLES ARE AVAILABLE IN PAIRS. WHEN ORDERING SPECIFY MOdEL NO. F40-0002


Alum. & S/S Only

D5800-526-3694

94% EFFICIENT AT GREASE EXTRACTIONAs tested by Underwriters laboratories of Canada it has been proven that Flame Gard 1 grease filters have the highest rate of grease extraction of any filter on the market today while still maintaining extremely low static pressures. Quoting U.l.C. File #CR1157 it was stated that the quantity of grease passing through the filter to the exhaust duct did not exceed 6% of the amount generated. (Please refer to the U.l.C. Report contained in the technical section of our full line catalog.)

SIMPLE BUT EFFECTIVE BAFFLE DESIGNFlame Gards U shaped baffles were arrived at after extensive testing. The smooth, deep baffles cause the grease to drain off the filter quickly, and they resist flame penetration without disturbing the movement of air. Flame Gards have more baffles per inch of filter which is a key factor in our high rate of grease extraction and out low static pressure. More baffles mean more grease impingement area and more paths for the air to flow smoothly and quickly through filter. These combined features make Flame Gard Is the most energy efficient filters available.

PTFE COATED BAFFLESFlame Gards high rate of grease extraction is aided by a PTFE coated baffle. In the same manner that grease rolls off a PTFE coated pan, it rolls down our baffles, out of the filter and into the hoods remote collection cup. Because Flame Gards filters retain only insignificant amounts of surface grease and do not load, you will have constancy of air flow throughout your operating day. In addition, Flame Gards filters can be easily cleaned in a pot sink or dishwasher with simple detergent and hot water.

TESTING METHODTwo sample steel filters were weighed and then mounted side by side in the hood. The damper was adjusted to provide a stack velocity of approximately 1800 f.p.m. The distance from the broiler surface to the bottom of the unit was approximately 36 in. The grease generator was weighed, partially filled with cooking oil, reweighed and the weighed recorded.

The grease generatory was placed on the electric broiler and heated until the temperature of the cooking oil was 400 F. The sizing of the spray nozzle was such that grease was discharged at approximately one pound per hour per foot width of the test hood.

The test continued for 2 hours...

At the end of the test, the grease laden filters were weighed. The grease collected from the filter run off was collected and weighed. The grease generator was weighed again to determine the weight of grease used.

MARYLAND LOCkING HANDLES AVAILABLE

TWO MODELS AVAILABLE....1. Standard Fixed Baffles2. Spark Arrestor Screen

SPARk ARRESTOR SCREENTHE 3/8 X 1/2 (9.5mm x 13mm) SPARK ARRESTOR SCREEN MEETS NFPA 211 REQUIREMENT FOR SOLID FUEL BURNING APPLIANCES

ALL STEEL CONSTRUCTION ALL SIZES AVAILABLE NON-LOADING PTFE COATED BAFFLES LOW STATIC PRESSURE

NATIONAL FIrE PrOTEcTION AssOcIATION NFPA 96, cHAPTEr 11-5.1 sTATEs

If airborne sparks and embers can be generated by the solid fuel cooking operation, spark arrestor devices shall be used prior to the grease removal device to minimize the entrance of these sparks and embers into the grease removal device and into the hood and duct system.

NFPA 211 cHAPTEr 1.11.2 (B) sTATEs:(b) The arrestor screen shall have heat and corrosion resistance equivalent to 19 gauge (0.011 in.) galvanized steel or 24 gauge (0.024 in.) stainless steel.(c) opening shall not permit the passage of spheres having a diameter larger than 1/2 in. (12.7mm) nor block the passage of spheres having a diameter of less than 3/8 in. (9.5mm).

CLASSIFIED BAFFLE GREASE FILTER MEETS NFPA 96 REQUIREMENT FOR COOkING WITH SOLID FUEL

TYPE I

C USLISTED


TYPE I - PTFE-coated Baffle & spark Arrestor

94% EFFICIENT AT GREASE EXTRACTION!The quantity of grease passing through the filter to the exhaust duct did not

exceed 6% of the amount generated!

RESULTSTHe FOllOwinG DATA wAS reCOrDeD On THe uniTS TeSTeD. 20 in. By 20 in. STeel PTFe COATeD FilTerS

WEIGHT OF GREASE GENERATED

Before TestAfter TestCooking Oil used

95 lb87.5 lb7.5 lb

weight BeforeTest

weight AfterTest

weight of Grease On Filter

Filter #1 15 lb 6 oz 15 lb 6 oz 0 oz

Filter #2 15 lb 5 oz 15 lb 5 oz 0 oz

Weight of oil collected from the grease filter run off 7 lb 4 oz. Amount of oil not retained or collected 1 oz. The quantity of grease passing through the filter to the exhaust duct did not exceed 6 percent of the amount generated.


TYPE I - PTFE-coated Baffle & spark Arrestor & TYPE II

HOW FLAME GARD WORkS

The affluent from cooking processes contains aerosols of water vapor mixed with evaporated fat or oil. These are carried from the cooking surface by the moving air being drawn into the exhaust hood.

Although small, each aerosol is much heavier than the air molecules surrounding it.

Thus, when the air stream containing these aerosols strikes the Flame Gard Baffle System, the inertial force of the moisture-grease aerosol is considerably greater than that of the air molecule. While the air molecule changes direction easily, the aerosol strikes the baffle with considerable force, causing it to splatter on the surface. Because the surface is coated with a PTFE, the grease slides down to the trough and then to the collecting container.

Whereas the heaviest aerosols, because of their greater inertial force, impinge on the surfaces of the baffles facing and perpendicular to the air flow, the lighter ones remain in the air stream. As the air stream is drawn through the baffle system, the restrictions in area created by the baffles cause the air to increase in velocity while changing direction by 180-degrees. Since the inertial force is a product of the mass and the square of the velocity, this increase in velocity serves to increase the inertial force of the remaining smaller aerosols, causing them to impinge on the inner surfaces of the baffles in the same manner in which the heavier aerosols impinged on the entering surfaces. The design of the baffle system provides several impingement surfaces and two rapid 180-degree direction changes.

Because Flame Gard removes grease aerosols from the air stream and drain them away instead of retaining them. There is no build-up of grease in the path of the air Flame Gard therefore, insures a constancy of air never before achievable with mesh-type filters.

SELECTION CHARTENGINEERING DATACFM - STATIC PRESSUREsTATIc PrEssurE - INcHEs OF H20cFM PEr FILTEr - (75 AIr)

*Measured 6 (152mm) behind Flame Gard Static pressure per filter, as included in this chart, represents the total static pressure for the system regardless of the number of filters used in the hood.

cFM

PEr

FIL

TEr

- (7

5 A

Ir)

Size 10 x 16 10 x 20 12 x 20 16 x 20 16 x 25 20 x 20 20 x 25350 .350 .185 .160 .075 .045 .030 .030400 .495 .240 .205 .095 .055 .055 .040450 .695 .310 .260 .120 .065 .065 .045500 .390 .325 .145 .080 .080 .055550 .485 .395 .175 .100 .100 .065600 .595 .475 .215 .120 .120 .080650 .720 .570 .255 .150 .150 .090700 .670 .300 .180 .180 .105750 .305 .210 .210 .120800 .400 .250 .230 .140850 .460 .290 .290 .165900 .530 .330 .330 .185950 .600 .380 .380 .2101000 .670 .430 .430 .2401050 .480 .480 .2751100 .540 .540 .3201150 .610 .610 .365

TYPE I

A complete list of governmental and industry approvals is available on request. See National Evaluation Service report No. NER-255 for allowable values and or conditions of use concerning material presented in this document. It is subject to re-examination, revisions, and possible cancellation. NER-255, Condition of Use - filters to be used in a kitchen exhaust system that is protected with an automatic fire suppression system.

UNDERWRITERS lABoRAToRIES, INC., Flame Gard Grease Filters are classified by Underwriters laboratories, Inc., as to flammability after exposure to grease-laden air only. Guide AKUS, File #R10173 see Underwriters laboratories Classified Building Materials Index.

Accepted for use, CITy oF NEW yoRK DEPARTMENT oF BUIlDINGS NO. MEA481-7.1-SM.

Meets the requirements of NATIoNAl FIRE PRoTECTIoN ASSoCIATIoN, Standard No. 96.

STAINLESS STEEL GREASE FILTERS DUAL ACTION

GREASE FILTER FEATURES:

ACTION ONE provides positive flame barrier protection. Its stainless steel interlocking baffle walls make it the most effective flame barrier of all filters marketed today.

ACTION TWO provides unsurpassed performance in efficient grease removal. The aerodynamic twin-wall V baffles continuously separate grease and air. Stainless steel surfaces assure constant run-off and allow grease to be safely deposited in collection troughs.

Safest baffle filter available Provides positive flame barrier protection Heavy Duty solid stainless steel welded construction Sturdy drop handles provided Polished vanes provide self-draining grease run off Highly efficient in grease removal Patented vane design prevents grease from dripping-food, utensils and burner surfaces remain clean

Rugged, welded stainless steel construction offers easy cleanability, can withstand todays harsh cleaning solutions, and fits in standard size dishwasher

Economical...NEVER NEEDS REPLACING Recommended by leading consultants and designers Meets requirements of Nation Fire Protection Association Bulletin #96 Tested and classified by UNDERWRITERS lABoRAToRIES, INC. FIlE #R10173

TYPE II

TABLE 1 HEIGHT OF GREASE FILTERSType of cooking Equipment Height Above cooking surface (ft.)

Without Exposed Flame 0.5

Exposed Flame 2.0

Charcoal Burning 2.0

D7800-526-3694

TYPE IIOPERATIONGrease laden air is drawn into the filter by the exhaust fans. As the air starts through the aerodynamic v baffle system, it undergoes a series of compressions, expansions and pressure changes. The heavy grease is deposited safely and quickly on the baffles while the grease-free air passes through the filter and up the exhaust duct. The baffles smooth surface enables the collected grease to run off into collection troughs without dripping on food, utensils or burner surfaces. The Component Hardware Grease filter method of separating grease and air has achieved superior levels for efficiency and safety not attained by competitors filters.

CONSTRUCTIONComponent Hardware stainless steel grease filters are constructed of heavy duty stainless steel, providing the most durable filter available in todays market, and will provide years of trouble-free operation. There are no coatings to wear out and no involved mechanisms which can jam. All stainless steel grease filters are guaranteed against defects in workmanship or materials.

MAINTENANCEThe all-stainless steel construction allows the filter to be soaked, sprayed or placed in a dishwasher for simplified cleaning, without concern for rusting or wearing out of surface coatings.

TYPE II - Heavy-duty stainless steel Grease Filters

C USLISTED


NSFCOMPONENT

STATIC PRESSURE

CFM per

Filter10x20 12x20 16x20 16x2520x20 25x20

150175200225250275300325350375400425450475500525550575600625650 675700725750775800825850875900925

.12

.18

.25

.31

.38

.46

.55

.63

.72

.84

.951.061.171.321.451.601.751.90

02.06.11.16.21.26.31.37.43.50.56.62.70.77.85.92

1.011.101.181.271.371.471.581.701.811.95

03.07.11.15.18.23.27.32.37.42.47.52.57.62.66.75.81.87.93

1.011.071.141.221.301.371.461.551.651.751.87

.03

.06

.09

.12

.15

.18

.22

.25

.28

.32

.36

.40

.44

.48

.52

.57

.62

.67

.72

.77

.82

.88

.931.001.061.121.171.23

.03

.04

.06

.08

.10

.12

.14

.16

.18

.21

.23

.25

.27

.30

.32

.35

.37

.41

.43

.46

.49

.53

.56

.60

.63

.67

.71

EFFECTIVE AREA CHARTNOMINAL (in)

L x W x TEFFECTIVE AREA

square Feet

10 x 20 x 212 x 20 x 216 x 20 x 216 x 25 x 220 x 20 x 220 x 25 x 2

1.001.251.752.242.252.88

ALL COMPONENT HARDWARE STAINLESS STEEL GREASE FILTERS ARE:

Classified by Underwriters laboratories Inc.-File #R 10173.

cOMPONENT HArdWArE GrOuP, INc. Grease filter classification by Underwriters laboratories, Inc., as to flammability only after exposure to grease-laden air. See U.l. Classified Building Material Index. File #R10173

140013001200110010009008007006005004003002001000

CFM

PER

FIL

TER

.20 .40 .60 .80 1.00 1.20 1.40 1.60 1.80 2.00STATiC PreSSure (measured in inches of H20)

AIR FLOW CHARACTERISTICS

20 x 25

16 x 25

20 x 20

16 x 20

12 x 20

10 x 20

SELF-BALANCINGWith conventional mesh filters, it is necessary to pull two to five times as much air through the center filter to get good smoke and grease vapor capture on the ends of a hood. This is a needless waste of costly heated or air conditioned air.

Component Hardware grease filters are aerodynamically designed to provide a self-balancing air flow throughout the entire length of a hood. Actual field tests have repeatedly shown a variation of less than 10 air flow from end to end. This unique design assures good capture through the entire hood length, with 25 to 50% less volume of exhaust air.

self-Balancing Air Flow

conventional Mesh Air Flow


HOW FLAME GARD WORkSThe affluent from cooking processes contains aerosols of water vapor mixed with evaporated fat or oil. These are carried from the cooking surface by the moving air being drawn into the exhaust hood. Although small, each aerosol is much heavier than the air molecules surrounding it. Thus, when the air stream containing these aerosols strikes the Flame Gard Baffle System, the inertial force of the moisture-grease aerosol is considerably greater than that of the air molecule. While the air molecule changes direction easily, the aerosol strikes the baffle with considerable force, causing it to splatter on the surface.

Whereas the heaviest aerosols, because of their greater inertial force, impinge on the surfaces of the baffles facing and perpendicular to the air flow, the lighter ones remain in the air stream. As the air stream is drawn through the baffle system, the restrictions in area created by the baffles cause the air to increase in velocity while changing direction by 180 degrees. Since the inertial force is a product of the mass and the square of the velocity, this increase in velocity serves to increase the inertial force of the remaining smaller aerosols, causing them to impinge on the inner surfaces of the baffles in the same manner in which the heavier aerosols impinged on the entering surfaces. The design of the baffle system provides several impingement surfaces and two rapid 180-degree direction changes. The grease slides down to the grease trough and then to the collection container.

Because Flame Gard removes grease aerosols from the air stream and drain them away instead of retaining them. There is no build-up of grease in the path of the air Flame Gard therefore, insures a constancy of air never before achievable with mesh-type filters.

TYPE III - stainless steel, Galvanized & Aluminum Grease Filters

CFM - Static PressureStatic Pressure - Inches of H20

10 x 16 10 x 2 0 16 x 16 16 x 20 16 x 25 20 x 16 20 x 20 20 x 25 25 x 16 25 x 20

200 .34 .19 .12 .07 .05 .09 .04 .03 .05 .03

300 .84 .48 .33 .19 .12 .23 .11 .07 .13 .07

400 1.46 .83 .57 .33 .21 .41 .19 .13 .23 .13

500 2.27 1.28 .86 .50 .32 .61 .29 .195 .355 .195

600 3.27 1.86 1.27 .73 .46 .90 .42 .28 .52 .29

700 4.45 2.53 1.73 .99 .63 1.23 .57 .38 .70 .39

800 5.73 3.32 2.26 1.30 .82 1.59 .74 .49 .92 .505

900 7.38 4.19 2.87 1.64 1.04 2.04 .94 .64 1.17 .65

1000 9.13 5.15 3.47 2.03 1.28 2.49 1.17 .78 1.425 .79

1100 6.24 4.27 2.44 1.55 3.04 1.40 .95 1.74 .97

1200 7.38 5.08 2.92 1.84 3.59 1.67 1.13 2.07 1.15

1300 8.74 5.98 3.42 2.17 4.26 1.97 1.33 2.44 1.35

1400 6.92 3.95 2.52 4.93 2.28 1.54 2.82 1.56

1500 7.95 4.55 2.89 5.66 2.61 1.77 3.24 1.80

TYPE III TYPE III sTAINLEss, ALuMINuM ANd GALVANIZEd FILTErs STATIC PRESSURE SELECTION CHART

A complete list of governmental and industry approvals is available on request.See National Evaluation Service report No. NER-255 for allowable values and or conditions of use concerning material presented in this document. It is subject to re-examination, revisions, and possible cancellation. NER-255, Condition of Use - filters to be used in a kitchen exhaust system that is protected with an automatic fire suppressions system.

UNDERWRITERS lABoRAToRIES, INC., Flame Gard Grease filters are classified by Underwriters laboratories, Inc., as to flammability after exposure to grease-laden air only. Guide AKUS, File #R10173, see Underwriters laboratories Classified Building Materials Index.

UNDERWRITERS lABoRAToRIES oF CANADA Guide No. 440E13; File No. CR1157.

Accepted for use, CITy oF NEW yoRK DEPARTMENT oF BUIlDINGS NO. MEA481-7.1-SM.

Meets the requirements of: NATIONAL FIRE PROTECTION ASSOCIATION, Standard No. 96.

SIZES / INSTALLATIONFlame Gard should always be installed with the baffles in a vertical position, in order to allow the grease particles to be drawn into the collection system by gravity.

Standard sizes are ordered with the vertical (top to bottom) dimension stated first, and the horizontal (left to right) dimension second. For information on sizes not listed, contact the factory, your representative, or your food-service equipment dealer.

STAINLESS STEEL

ALUMINUM

GALVANIZED

ALL TESTS CONDUCTED BY CEDRT-AIRE TECHNICAL SERVICES TO AMCA STANDARD 500-89

TABLE 1 HEIGHT OF GREASE FILTERS

Type of cooking Equipment Height Above cooking surface (ft.)

Without Exposed Flame 0.5

Exposed Flame 2.0

Charcoal Burning 2.0

C USLISTED


D9800-526-3694

UNIQUE Roll RoCK CAN SEAM DESIGN MAKES TyPE III THE MoST DURABLE FILTER ON THE MARKET WILL NOT FLEX OR TWIST LIKE OTHER FILTERS EVEN AFTER REPEATED DROPPING SAFE, DEPENDABLE, POSITIVE FLAME BARRIER PROTECTION SEAMLESS, SMOOTH SURFACES PERMIT CONSTANT PERMIT GREASE RUN-oFF INTo HooD CollECTIoN TRoUGHS...EASIly ClEANED By SOAKING, SPRAYING OR IN CONVENTIONAL DISHWASHERS

ALL STAINLESS STEEL CONSTRUCTION: IS DURABLE AND CoRRoSIoN-RESISTANT

BRIGHT FINISH: AESTHETICALLY PLEASING, IDEAL FOR FRoNT-oF-HoUSE INSTAllATIoNS

EFFICIENT: REMOVES A SIGNIFICANT AMOUNT OF GREASE BEFORE IT CAN ENTER THE VENTILATION SYSTEM, HELPING TO PROTECT BLOWER EQUIPMENT AND MOTOR

LOW STATIC PRESSURE: INSURES QUIET OPERATION AND REDUCES OPERATING COSTS

sANITArY: SMooTH, BRIGHT FINISH PRoMoTES GREASE RUN-oFF, KEEPING FILTERS CLEANER FOR A LONGER PERIOD OF TIME

POsITIVE FIrE-BArrIEr PrOTEcTION: UNIQUE BAFFLE DESIGN LESSENS THE RISK OF KITCHEN HOOD FIRES SPREADING INTO DUCTWORK

EASY INSTALLATION: TWO HANDLES ON FACE OF FILTER MAKE IT EASy To INSTAll/REMovE FIlTERS

WASHABLE: FILTERS MAY BE ROUTINELY CLEANED TO ENSURE THEY OPERATE AT MAXIMUM EFFICIENCY

TYPE IV

TYPE V

20mm TYPE IV BAFFLE GREASE FILTER

COMPONENT HARDWARE GROUP: GREASE FILTER CLASSIFIED BY UNDERWRITERS LABORATORIES, INC. AS TO FLAMMABILITY AFTER EXPOSURE TO GREASE LADEN AIR oNly (54-H6). FIlE #R10173 (N) ACCEPTED By THE CITy oF NEW yoRK-DEPARTMENT OF BUILDINGS-MEA#137-82-E, VOL.2

NoTE: FIRST TWo NUMBERS oF SIZE INDICATE vERTICAl HEIGHT. SECoND TWo NUMBERS REPRESENT HoRIZoNTAl WIDTH, BoTH ARE NoMINAl DIMENSIoNS. ACTUAl SIZE oF FIlTERS ARE 7/16(11mm) lESS THAN NoMINAl. NoMINAl THICKNESS IS 2 (51mm). ACTUAl THICKNESS IS 1-3/4(44mm). STANDARD PACKAGE CoNSISTS oF SIX FIlTERS.

TYPE IV & TYPE V Baffle Grease Filters

GALVANIZED STEELFG35 sErIEsFor strong rugged performance, superb corrosion resistance and absolute low cost

TYPE V BAFFLE TYPE GREASE FILTERSSTANDARD COMMERCIAL SIZES

PATENT 6840975

ALUMINUMFA30 SERIESlightweight for ease of handling

NSFCOMPONENT

STAINLESS STEEL & S/S BRIGHT FINISHFs50 sErIEsFor tough commercial applications and maximum permanent protection against rust and corrosion

NSFCOMPONENT

ALL FILTERS ARE SUPPLIED WITH STANDARD BAIL HANDLES. FILTERS

WITH LOCKING HANDLES ARE AVAILABLE TO COMPLY WITH MARYLAND, VIRGINIA AND

WASHINGTON D.C. SPECIFICATIONS FOR COMMERCIAL HOODS. TO

ORDER STATE SIZE WITH PREFIX...FA31...FOR ALUMINUM

FG36...FOR GALVANIZED STEEL FS51...FOR STAINLESS STEEL

REPLACEMENT LOCKING HANDLES ARE AVAILABLE IN PAIRS. WHEN ORDERING

SPECIFY MODEL NO. F40-0002.

FG20 sErIEs

C USLISTED



BAFFLE TYPE GREASE FILTER AIR FLOW CHARACTERISTICSseries FA30, FG35, Fs50

CFM VS STATIC PRESSURE

FLOW RATESTATIC PRESSURE

FILTEr sIZE: H & W INcHEs (mm)

CFM(m3/min)

10 x 20 (254 x 508)

12 x 16 (305 x 406)

12 x 20(305 x 508)

16 x 16(406 x 406)

16 x 20(406 x 508)

20 x 20(508 x 508)

16 x 25(406 x 635)

20 x 25(508 x 635)

200 5.6) 0.13 0.15 0.10 0.07 0.04 0.04 0.04 0.03

250 (7.0) 0.27 0.31 0.22 0.16 0.09 0.08 0.09 0.05

300 (8.5) 0.39 0.45 0.31 0.23 0.12 0.13 0.12 0.08

400 (11.3) 0.7 0.8 0.54 0.41 0.23 0.21 0.23 0.15

450 (12.7) 0.89 1.01 0.69 0.51 0.28 0.25 0.28 0.19

500 (14.1) 1.1 1.26 0.85 0.62 0.35 0.32 0.35 0.24

550 (15.6) 1.33 1.52 1.03 0.76 0.43 0.39 0.42 0.28

600 (17.0) 1.58 1.22 0.91 0.51 0.46 0.51 0.34

650 (18.4) 1.44 1.07 0.61 0.52 0.61 0.41

700 (19.8) 1.23 0.7 0.61 0.69 0.47

750 (21.2) 1.42 0.8 .7 .8 0.54

800 (22.6) 0.92 0.8 0.91 0.61

850 (24.0) 1.03 0.89 1.01 0.69

900 (25.5) 1.15 0.99 1.15 0.77

950 (26.9) 1.29 1.11 1.27 0.87

1000 (28.3) 1.42 1.24 1.41 0.96

TYPE V

EFFECTIVE AREATHE EFFECTIVE AREA FOR NOMINAL SIZE

FILTERS ARE AS LISTED

FILTER SIZE: H & W INcHEs (mm)

EFFECTIVE AREAsq. FEET (sq. METErs)

10 x 20 (254 x 508)

1.00 (0.9)

12 x 16 (305 x 406)

0.97 (.09)

12 x 20 (305 x 508)

1.25 (.11)

16 x 16 (406 x 406)

1.36 (.12)

16 x 20 (406 x 508)

1.75 (.16)

20 x 20 (508 x 508)

2.25 (.20)

16 x 25 (406 x 635)

2.24 (.20)

20 x 25 (508 x 635)

2.88 (.26)

MESH TYPE AIR FILTERSstandard commercial sizes Available in...

ALuMINuM FrAMEd MOdELs and GALVANIZED STEEL FRAMED MODELS

RIGID HEAVY DUTY CONSTRUCTION BEST PRICING CORROSION RESISTANT ALL STEEL WIRE MESH DESIGN FOR

MAXIMUM CAPTURE OF DUST PARTICLES

ACCEPTED FOR USE BY THE CITY OF NEW YORK DEPARTMENT OF BUILDING MEA #57-82M

NoTE: STANDARD PACKAGE CoNSISTS oF SIX FIlTERS. NoMINAl THICKNESS IS 2 (51mm)...actual thickness is 1-3/4(44mm). actual height and width are 7/16(11mm) less than nominal sizes listed. special size filters and 1(25mm) filters are furnished without handles lift handles are available on application. all stainless steel (frame and media) models available on application.

GALVANIZED STEEL FRAMEDF41 SERIES

ALUMINUM FRAMEDF40 SERIES

OPTIONAL SNAP-ON HANDLES AVAILABLE

(FURNISHED IN PAIRS) SPECIFY...MODEL NO. F41-0001

AIR DELIVERY DATA CHART

NET FACE VELOCITY

RESISTANCE IN INCHES OF W.G.

NOMINAL THICkNESS

CFMCAPACITY BY SIZE

FPM I INCH 2 INCH 16 x 20 16 x 25 20 x 20 20 x 25

267 .025 .020 467 597 600 768

356 .040 .038 623 796 800 1024

445 067 .060 779 995 1000 1279

533 .100 .090 933 1192 1200 1532

622 .142 .129 1089 1391 1400 1788

711 --- .169 1244 1590 1600 2044

800 --- .218 1400 178 1800 2300

MESH TYPE AIR FILTERS

HEIGHT & WIDTH ALUMINUM FRAMED GALVANIZED STEEL FRAMED

sIZE: INcHEs (mm) MODEL NO. PACkAGE WGT: LBs. (kg) MODEL NO.PACkAGE WGT:

LBs. (kg)

10 x 20 (254 x 508) F40-1020 11 (5) F41-1020 14 (6)

16 x 20 (406 x 508) F40-1620 18 (8) F41-1620 23 (10)

16 x 25 (406 x 635) F40-1625 22 (10) F41-1625 28(13)

20 x 20 (508 x 508) F40-2020 22 (10) F41-2020 28 (13)

20 x 25 (508 x 635) F40-2025 26 (12) F41-2025 33 (15)

Air Flow characteristics & Mesh Type Air Filters

D11800-526-3694

E-Z MOUNT INCANDESCENT CANOPY LIGHTING FIXTURES FOR COMMERCIAL COOkING HOODS

E-Z MOUNT FEATURE ALLOWS FOR QUICK INSTALLATION GASKETS PERMANENTLY AFFIXED SAVE INSTALLATION TIME U.L. LISTED AND C.S.A. CERTIFIED FOR USE IN COMMERCIAL COOKING HOODS MEETS ALL REQUIREMENTS FOR NFPA 96 AND N.E.C. 410

DESIGNED FOR CONVENIENT INSTALLATION TO PREWIRED HOODS GREASEPROOF, WATERPROOF AND HEATPROOF CONSTRUCTION ALUMINUM FIXTURES ARE FURNISHED WITH A BRUSHED FINISH TO MATCH STAINLESS STEEL HOOD INTERIORS

NoTE: **SIlICoNE CoATED GloBES PRovIDED WITH TUFF-SkIN COATING WHICH ELIMINATES HoT SPoT BRoWNING / DISColoRATIoN oF GloBE...PREvENTS GlASS SHATTER FRoM IMPACT, DROPPING, UNUSUAL STRESSES AND THERMAL SHOCK. SCRATCH RESISTANT...U.S.D.A. APPROVED... IMPROVES LIGHT SOURCE BY PROVIDING BETTER DIFFUSION.

UNDERWRITERS LABORATORIES STANDARD #1571 REQUIRES THAT FIXTURES IN COMMERCIAL COOKING HooDS MUST BE MoUNTED A MINIMUM oF 4 FEET (1219mm) ABovE THE CooKING SURFACE.

B

C

D

A

SPECIFICATIONS FIXTURE BODY: Die cast aluminum with brushed finish SOCkET: Porcelain body with copper shell WIRE LEADS: 16 AWG, 6 (152mm) long GROUND LEAD: 6 (152mm) long green colored 18 AWG wire WATTAGE: Accepts standard 100 watt A19 bulb (not furnished) VOLTAGE: Rated up to 120 volts GASkETS: Silicone GLOBES: Silicone* or clear, thermal and shock resistant tempered glass WIRE GUARD: Plated steel OVERALL SIZE: 5-1/2(140mm) diameter and 8-3/4(222mm) long with wire guard jUNCTION BOX: Not furnished. Fixture is designed to accept any standard 3-1/2(89mm) or 4(102mm) junction box

E-Z MOUNT CANOPY LIGHTING FIXTURES

REF.U.L.

MODEL NO.CSA

MODEL NO.DESCRIPTION

CASEQTY

A L55-1004

*L55-1004-HTL55-1004-csA

FURNISHED WITH TUFF-SKIN COATED** THERMAL AND SHOCK RESISTANT

TEMPERED GLASS GLOBE32

BL55-1024

*L55-1024-HTL55-1024-csA

FURNISHED WITH TUFF-SKIN COATED** THERMAL AND SHOCK RESISTANT

TEMPERED GLASS GLOBE AND WIRE GUARD 32

C L55-2004

*L55-2004-HTL55-2004-csA

FURNISHED WITH THERMAL, SHOCK RESISTANT TEMPERED GLASS GLOBE

32

DL55-2024

*L55-2024-HTL55-2024-csA

FURNISHED WITH THERMAL, SHOCK RESISTANT TEMPERED

GLASS GLOBE AND WIRE GUARD32

NoTE: MoDElS WITH WIRE GUARD ARE NoT NSF APPRovED*AvAIlABlE AS HIGH TEMP MoDElS RATED To 392F (200C), 600v, lEADS: 14 AWG, 6 (152mm)

loNG STRIPPED END. INSUlATIoN: SIlICoNE RUBBER WITH TREATED GlASS BEAD SlEEvING

E-Z Mount Incandescent canopy Lighting Fixtures

CERTIFIEDFile No. LR63261

C USLISTED

File No. E80045

NSFCOMPONENT

PATENT PENDING

NEW E-Z MOUNT FEATURE CUTSINSTALLATION TIME bY 50%

NEW

FEATUR

E!


L55 sErIEs LIGHTING FIxTurE rEPLAcEMENT PArTs

REF. MODEL NO. DESCRIPTION CASE QTY

A L55-x022 GLOBE, TEMPERED GLASS

THERMAL AND SHOCK RESISTANT 32

B L50-x011 GLOBE, TEMPERED GLASS SILICONE**

COATED, THERMAL AND SHOCK RESISTANT32

C L10-x020 WIRE GUARD 32

DL55-Y001

L55-Y001-csA*L55-Y001-HT

LAMP HOUSING ASSEMBLY COMPLETE WITH PORCELAIN SOCKET

AND REQUIRED SILICONE GASKET32

E L55-x006 SCREW 32

F L50-x009 ADAPTER PLATE 300

GL55-x003

*L55-x003-HT PORCELAIN SOCKET 50

H L50-Y001 GASKET SET

*AvAIlABlE AS HIGH TEMP MoDElS RATED To 392F (200C), 600v, lEADS: 14 AWG, 6 (152mm) loNG STRIPPED END. INSUlATIoN: SIlICoNE RUBBER WITH TREATED GlASS BEAD SlEEvING

NoTE: **SIlICoNE CoATED GloBES PRovIDED WITH TUFF-SkIN COATING WHICH ELIMINATES HoT SPoT BRoWNING / DISColoRATIoN oF GloBE...PREvENTS GlASS SHATTER FRoM IMPACT, DROPPING, UNUSUAL STRESSES AND THERMAL SHOCK. SCRATCH RESISTANT...U.S.D.A. APPROVED... IMPROVES LIGHT SOURCE BY PROVIDING BETTER DIFFUSION.

UNDERWRITERS LABORATORIES STANDARD #1571 REQUIRES THAT FIXTURES IN COMMERCIAL COOKING HooDS MUST BE MoUNTED A MINIMUM oF 4 FEET (1219mm) ABovE THE CooKING SURFACE.

E-Z Mount Incandescent replacement Parts

G

C

DA

F

B

E

H

E-Z MOUNT INCANDESCENTL55 sErIEs LIGHTING FIxTurE rEPLAcEMENT PArTs

CERTIFIEDFile No. LR63261

D13800-526-3694

NSFCOMPONENT

NSFCOMPONENT

recessed Fluorescent canopy Lighting Fixtures

RECESSED FLUORESCENT...LOW PROFILE NSF LISTED, UL LISTED E250943 FOR USE IN COMMERCIAL COOKING HOODS

MEETS ALL REQUIREMENTS FOR NFPA 96 AND N.E.C. 410 oNly 4-1/2 (114mm) HIGH...FoR lIMITED ovERHEAD ClEARANCE APPlICATIoNS

TEMPERED, PRISMATIC GLASS DIFFUSER WITH ONE PIECE SATIN FINISHED STAINLESS STEEL FACE FRAME TO MATCH HOOD INTERIOR

FLUORESCENT CANOPY HOOD LIGHT FIXTURES

SPECIFICATIONS BALLAST: Universal 120-277v, 50 or 60 Hz, T8, Ul listed LAMPS: T8 Fluorescent lamps (not furnished) BODY: Steel with baked white enamel finish MOUNTING: #10-32 x 3/4 (19mm) long threaded studs REFLECTOR: Baked white enamel finish... providing a minimum of 87% diffused reflection

DIFFUSER: Crystal 73 tempered prismatic glass with prisms on inside of fixture, mounted into a stainless steel face frame with special sealing gasketing. Secured to fixture body with stainless steel screws for easy servicing.

RECESSED FLUORESCENT CANOPY HOOD LIGHT FIXTURES

REFMODEL

NO.LAMPS REQD

OVERALLTRIM SIZE

CUT-OUTSIZE

HOLES REQD

DIM.

A L82-1020 (2) F17T810-1/4 x 26-1/4

(260mm x 667mm)8-1/2 x 24-1/2

(216mm x 622mm)12

6 (152mm)

B L82-1030 (2) F25T810-1/4 x 38-1/4

(260mm x 972mm)8-1/2 x 36-1/2

(216mm x 927mm)14

7-1/2 (191mm)

C L82-1040 (2) F32T810-1/4 x 50-1/4

(260mm x 1276mm)8-1/2 x 48-1/2

(216mm x 1232mm)14

10-1/2 (267mm)

9-3/16(233mm)

1/4(6mm) DIA. HOLES

CUT-OUT

3-1/4(83mm)

3-1/4(83mm)

A A A A

MOUNTING CUT-OUT DIAGRAM

210-1/4 (260mm)

8(203mm)

4-1/2 (114 mm)

SECTION

C USLISTED

File No. E250943

C USLISTED

File No. E253411

A B

C

RECESSED INCANDESCENT CANOPY HOOD LIGHT FIXTURE UL LISTED E253411 AND CERTIFIED FOR CANADA FOR USE IN COMMERCIAL COOKING HOODS

MEETS ALL REQUIREMENTS FOR NFPA 96 AND N.E.C. 410 NSF LISTED TEMPERED, PRISMATIC GLASS DIFFUSER

SATIN FINISHED STAINLESS STEEL FACEPLATE TO MATCH HOOD INTERIORS

SPECIFICATIONS SOCkET: Side mounted porcelain medium base WATTAGE: Accepts standard 150 Watt A23 bulb maximum (not furnished) VOLTAGE: Rated up to 120 volts DIFFUSER: Crystal 73 tempered prismatic glass with prisms on inside of fixture FACEPLATE: one piece, stainless steel with smooth satin finish LOCkUP: (4) captive stainless steel screws RETAINER: Twin spring and cable for faceplate and frame REFLECTOR: Die formed aluminum with satin finish WIRING: Connections to socket are made in the interior removable thermal insulated wiring chamber BODY: Steel recessed housing with baked white enamel finish MOUNTING: (4) #10-24 x 3/4 (19mm) long threaded studs

MOdEL NO. L87-1004

13-3

/8

(340

mm

)6

(152

mm

)

11-3/4(298mm)

13-3/8(340mm)

1/4(6mm)

DIA. HOLES


quick-Tite Fittings & Hole Plugs

USED AS THRoUGH-PENETRATIoN FITTINGS IN CooKING HooD SySTEMS

PROVIDES STRUCTURAL SUPPORT FOR THE SYSTEM PIPING, IMPROVING SYSTEM INTEGRITY ANDREDUCING THE NEED FOR ADDITIONAL PIPE HANGERS

AvAIlABlE IN EIGHT STANDARD SIZES To ACCoMMoDATE PIPE SIZES FRoM 1/4 To 1-1/2 PIPE

All QUICK-TITE FITTINGS ARE PRESSURE TESTED To 5000 PSI

TESTED AND LISTED BY UNDERWRITERS LABORATORIES UNDER HOOD AND DUCT ACCESSORIES (CoMPATIBlE WITH Ul lISTED FIRE SUPPRESSIoN SySTEMS)

IN CONFORMANCE WITH THE REQUIREMENTS OF NFPA STANDARD NO. 96

MANUFACTURED OF SOLID MACHINED STEEL FOR SUPERIOR STRENGTH AND HIGH TEMPERATURE RESISTANCE

SUPPLIED WITH A CHROME PLATED FINISH TO MAXIMIZE CORROSION RESISTANCE AND ATTRACTIVE APPEARANCE

FITTINGS ARE PROVIDED WITH INTERNAL PIPE THREADS TO PERMIT EASY COUPLING OF THE PIPES AT THE POINT OF PENETRATION

C USLISTED3RS9

File No. MH19744

C USLISTED3RS9

File No. MH19744

MODEL NO. QuIck-TITE FITTING WT. PER FITTINGCASE QTY

F11-0014 1/4 (6mm) Pipe 2.5 oz (71g) 24

F11-0038 3/8 (10mm) Pipe w/ 1-1/8 (29mm) Hole 3.3 oz (94g) 24

F11-0038A 3/8 (10mm) Pipe w/ 7/8 (22mm) Hole 5.8 oz (164g) 24

F11-0012 1/2 (13mm) Pipe 5.3 oz (150g) 24

F11-0034 3/4 (19mm) Pipe 8.3 oz (235g) 12

F11-0100 1 (25mm) Pipe 13.5 oz (383g) 8

F11-0114 1-1/4 (32mm) Pipe 15.5 oz (439g) 8

F11-0112 1-1/2 (38mm) Pipe 19.0 oz (539g) 8

QUICK-TITE HolE PlUGS ARE DESIGNED To PRovIDE A PoSITIvE SEAl oR PATCH FOR EXISTING PENETRATIONS THAT ARE NO LONGER REQUIRED

IDEAL TO REPAIR UNWANTED HOLES AS A RESULT OF CHANGES TO A FIRE PROTECTION SYSTEM, MOVING THE LOCATION OF A FIRE SUPPRESSION NOZZLE, DRILLING A HOLE AT THE WRONG

loCATIoN oR USING A HooD/DUCT WITH PREvIoUSly DRIllED HolES

QUICK-TITE HolE PlUGS ARE EASy To INSTAll AND PRovIDE AN ATTRACTIvE, FINISHED APPEARANCE TO MATCH FITTINGS

AvAIlABlE FoR FIvE STANDARD HolE SIZES - 3/4, 7/8, 1-1/8, 1-3/8, AND 1-5/8

MODEL NO. HOLE SIZE WT. PER HOLE PLUGCASE QTY

F12-0034 3/4 (19mm) to 7/8 (22mm) 3.2 oz (91g) 24

F12-0078 7/8 (22mm) to 1 (25mm) 4.8 oz (136g) 24

F12-0118 1-1/8 (29mm) to 1-5/16 (33mm) 7.2 oz (204g) 12

F12-0138 1-3/8 (35mm) to 1-9/16 (40mm) 12.8 oz (363g) 12

F12-0158 1-5/8 (41mm) to 1-7/8 (48mm) 21.6 oz (612g) 6

QUICk-TITE FITTINGS

QUICk-TITE HOLE PLUGS

MODEL NO. CORNER PULLEY WT. PER PULLEY CASE QTY

F11-0012A 7/8-18 x 1/2 NPT 5.1 oz (145g) 24

F11-0012B 15/16-20 x 1/2 NPT 4.9 oz (139g) 24

D15800-526-3694

PLUG bODY(replaces adapter body

when ordering Hole Plug)

ADAPTER bODY

GASKET

METAL WALLNUT LOCK

WASHER

ADAPTERbODY

GASKETHOOD

orDUCT

LOCKWASHER

NUTA

b

D

C

MODEL NO. SIZE OF PIPEA = CUT OUT

HOLE SIZEB C D

F11-0014 1/4 (6mm) 3/4 (19mm) to 7/8 (22mm) 0.88 1.13 hex 0.25

F11-0038 3/8 (10mm) 1-1/8 (29mm) to 1-5/16 (33mm) 1.00 1.50 hex 0.31

F11-0038A 3/8 (10mm) 7/8 (22mm) to 1 (25mm) 1.00 1.50 hex 0.31

F11-0012 1/2 (13mm) 1-1/8 (29mm) to 1-5/16 (33mm) 1.14 1.50 hex 0.31

F11-0034 3/4 (19mm) 1-3/8 (35mm) to 1-9/16 (40mm) 1.25 1.88 hex 0.31

F11-0100 1 (25mm) 1-5/8 (41mm) to 1-7/8 (48mm) 1.50 2.25 hex 0.38

F11-0114 1-1/4 (32mm) 2 (51mm) to 2-1/4 (57mm) 1.50 2.50 hex 0.38

F11-0112 1-1/2 (38mm) 2-1/4 (57mm) to 2-1/2 (64mm) 1.50 2.75 hex 0.38

QUICk-TITE ASSEMBLY BREAkDOWN

HOLE PLUG DIMENSIONAL DRAWING

REPAIR kIT INCLUDES 1 TUBE - SIl300 HIGH TEMPERATURE SIlICoNE ADHESIvE,

10.3 oZ (305ml) CARTRIDGE WITH REMovABlE TIP

1 Roll - HIGH TEMPERATURE SIlICA CloTH GASKET, .090 (2.3mm) THICK X 1.5 (38mm) WIDTH X 50 (15m) lENGTH

GASkET REPAIR kIT

SIL300 SILICONE FIRESTOP SEALANT IS:

CLASSIFIED

C US 3L73

fILL, VOID OR CAVITY MATERIAL CLASSIfIED BY UNDERWRITERS LABORATORIES INC. fOR USE IN THROUGH-PENETRATION fIRESTOP SYSTEMS.

SEE UL fIRE RESISTANCE DIRECTORY UNDERWRITERS LABORATORIES CLASSIfIED WALL PROTECTION MATERIAL. SEE PRODUCT CATEGORY IN UL fIRE RESISTANCE DIRECTORY

CLASSIfIED fILL, VOID, OR CAVITY MATERIALS fOR USE IN THROUGH-PENETRATION fIRESTOP SYSTEMS. SEE UL DIRECTORY Of PRODUCTS CERTIfIED fOR CANADA AND UL fIRE RESISTANCE DIRECTORY

FMAPPROVED

MOdEL NO. 750002 EXTEND THE SERVICE LIFE OR REPAIR OF UL FIRE RATED ACCESS DOORS

GASKET MATERIAL MAXIMUM SERVICE TEMPERATURE IS RATED TO 2,300F, 1260C

SILICONE ADHESIVE IS UL CLASSIFIED AND FACTORY MUTUAL APPROVED

UL APPROVED GASKET AND ADHESIVE MUST BE USED TOGETHER TO RETAIN THE UL LISTING ON YOUR FLAME GARD ACCESS PANEL

KIT INClUDES ENoUGH MATERIAl To REPAIR 7-16 ACCESS DooRS, DEPENDING oN DooR SIZES

quick-Tite Assembly Breakdown & Gasket repair kit


Curved Access Doors UL Fire Rated

CURVED ACCESS DOORS

MODEL NO.PANEL OUTSIDE DIMENSIONS

Inches (mm)HOLE SIZE

Inches (mm)

A B C D

750505-c 6.56 (167mm) 6.75 (171mm) 5.06 (129mm) 5.25 (133mm)

750511-c 6.50 (165mm) 12.75 (324mm) 5.00 (127mm) 11.25 (286mm)

750517-c 6.50 (165mm) 18.75 (476mm) 5.00 (127mm) 17.25 (438mm)

750808-c 9.50 (241mm) 9.75 (248mm) 8.00 (203mm) 8.25 (210mm)

750811-c 9.50 (241mm) 12.75 (324mm) 8.00 (203mm) 11.25 (286mm)

750817-c 9.50 (241mm) 18.75 (476mm) 8.00 (203mm) 17.25 (438mm)

750823-c 9.50 (241mm) 24.75 (629mm) 8.00 (203mm) 23.25 (591mm)

751117-c 12.50 (318mm) 18.75 (476mm) 11.00 (279mm) 17.25 (438mm)

751123-c 12.50 (318mm) 24.75 (629mm) 11.00 (279mm) 23.25 (591mm)

751717-c 18.50 (470mm) 18.75 (476mm) 17.00 (432mm) 17.25 (438mm)

751723-c 18.50 (470mm) 24.75 (629mm) 17.00 (432mm) 23.25 (591mm)

EASY TO CLEAN AND EASY TO INSTALL

GASKET RATED To 2300F (1260C) FOR FIRE TIGHT SEAL GASKET IS HIGH-TEMP BoNDED To FRoNT PANEl

AVAILABLE WITH EXTENDED STUDS TO ACCOMMODATE FIRE WRAP FOR CURVED DUCT APPLICATIONS

HEAvy-DUTy 16 GAUGE STEEl CoNSTRUCTIoN STAINLESS STEEL MODEL AVAILABLE NO MINIMUM ORDER REQUIREMENTS

PoSITIvE BolT PATTERN ENSURES FIRE-SAFE CloSURE BACK FRAME REINFoRCES DUCT CUT-oUT

STANDARD AND CUSTOM SIZES AVAILABLE

HOOD AND DUCT ACCESSORY

65X3

File No. MH16475NFPA #96

UL FIRE RATED CURVED ACCESS DOORS

D17

Component Hardware Group, inc.1890 Swarthmore Avenue, PO Box 2020, Lakewood, NJ 08701 Tel. 800-526-3694 732-363-4700 Fax 732-364-8110

www.flamegardusa.com

ORDER FORM-FOR CURVED ACCESS DOOR PANELS

MODEL NO:

DUCT DIAMETER:

QTY:

Additional Notes:

Note: All access panels are custom manufactured per order and are not returnable for credit.


65X3


e-Clipweld nuts

reverse view of Access Frame

Stud in Center of radius

D

D

C

C Access Frame(Mounted on inside of Duct)

Gasket (Permanently attached to Access Panel)

Access Panel

wing nuts

wing Screws

*The cut out dimension C should be 70% or less than the Duct Diameter for proper fit.

A

b

Date: P.O. # Account No:

Company Name: Contact Name:

Address: City & State: Zip:

Phone No: E-mail:

MATERIAL bACK PLATE: Cold rolled Steel, Thickness 0.057(1.5mm) FRONT PLATE: Galvanized Steel, Thickness 0.060(1.5mm)

ORDER BY MODEL NO.

PANEL OUTSIDE DIMENSIONSInches (mm)

HOLE SIZE Inches (mm)

A B C D

750505-c 6.56 (167mm) 6.75 (171mm) 5.06 (129mm) 5.25 (133mm)

750511-c 6.50 (165mm) 12.75 (324mm) 5.00 (127mm) 11.25 (286mm)

750517-c 6.50 (165mm) 18.75 (476mm) 5.00 (127mm) 17.25 (438mm)

750808-c 9.50 (241mm) 9.75 (248mm) 8.00 (203mm) 8.25 (210mm)

750811-c 9.50 (241mm) 12.75 (324mm) 8.00 (203mm) 11.25 (286mm)

750817-c 9.50 (241mm) 18.75 (476mm) 8.00 (203mm) 17.25 (438mm)

750823-c 9.50 (241mm) 24.75 (629mm) 8.00 (203mm) 23.25 (591mm)

751117-c 12.50 (318mm) 18.75 (476mm) 11.00 (279mm) 17.25 (438mm)

751123-c 12.50 (318mm) 24.75 (629mm) 11.00 (279mm) 23.25 (591mm)

751717-c 18.50 (470mm) 18.75 (476mm) 17.00 (432mm) 17.25 (438mm)

751723-c 18.50 (470mm) 24.75 (629mm) 17.00 (432mm) 23.25 (591mm)

Optional 4(102 mm) studs for zero clearance duct

wrap-order with Suffix (-4)

D18




Phone No: E-mail:

Additional Notes

DIMENSIONS SIZE INCHES orMM

DuCT DiAMeTer A

*CuT OuT DiMenSiOn CC = 70% x A or leSS

iF leSS THAn 70% Give Size

CuT OuT DiMenSiOn D

QUANTITY REQUIRED

MOUNTING HARDWARE MATERIAL

Check One

zinC PlATeD STeelSTAinleSS STeel 304STAinleSS STeel 316l

PANEL THICKNESS Check One

.050 (1.3mm) S/S Models only

.060 (1.5mm)

.125 (3.2mm)

PANEL MATERIAL Check One

GAlvAnizeD STeel

STAinleSS STeel 304

STAinleSS STeel 316l


65X3


e-Clipweld nuts

reverse view of Access Frame

Stud in Center of radius

D

D

C

C Access Frame(Mounted on inside of Duct)

Gasket (Permanently attached to Access Panel)

Access Panel

wing nuts

wing Screws

*The cut out dimension C should be 70% or less than the Duct Diameter for proper fit.

Order Form-For custom curved Access door Panels



A

b

Optional 4(102 mm) studs for zero clearance duct

wrap-order with Suffix (-4)

D19800-526-3694

FLAT ACCESS DOORS

MODEL NO. PANEL OUTSIDE DIMENSIONPANEL

HEIGHTSTUD

HEIGHTHOLE SIZE

Inches (mm)MTG

STUDS

A B C D E F

750710 7 (178mm) 10 (254mm) FLAT 1 (25mm) 5.5 (140mm) 8.5 (216mm) 6

750715 7 (178mm) 15 (381mm) FLAT 1 (25mm) 5.5 (140mm) 13.5 (343mm) 6

750723 7 (178mm) 23 (584mm) FLAT 1 (25mm) 5.5 (140mm) 21.5 (546mm) 10

750606 8 (203mm) 8 (203mm) FLAT 1 (25mm) 6 (152mm) 6 (152mm) 4

750707 10 (254mm) 10 (254mm) .5 (13mm) 1 (25mm) 7 (178mm) 7 (178mm) 4

750712 10 (254mm) 15 (381mm) .5 (13mm) 1 (25mm) 7 (178mm) 12 (305mm) 6

750720 10 (254mm) 23 (584mm) .5 (13mm) 1 (25mm) 7 (178mm) 20 (508mm) 10

751212 15 (381mm) 15 (381mm) .5 (13mm) 1 (25mm) 12 (305mm) 12 (305mm) 8

751220 15 (381mm) 23 (584mm) .5 (13mm) 1 (25mm) 12 (305mm) 20 (508mm) 14

751620 19 (483mm) 23 (584mm) .5 (13mm) 1 (25mm) 16 (406mm) 20 (508mm) 16

752020 23 (584mm) 23 (584mm) .5 (13mm) 1 (25mm) 20 (508mm) 20 (508mm) 16

EASY TO CLEAN AND EASY TO INSTALL

GASKET RATED To 2300F (1260C) FOR FIRE TIGHT SEAL GASKET IS HIGH-TEMP BoNDED To FRoNT PANEl

AVAILABLE WITH EXTENDED STUDS TO ACCOMMODATE FIRE WRAP FOR FLAT DUCT APPLICATIONS

HEAvy-DUTy 16 GAUGE STEEl CoNSTRUCTIoN STAINLESS STEEL MODEL AVAILABLE NO MINIMUM ORDER REQUIREMENTS

PoSITIvE BolT PATTERN ENSURES FIRE-SAFE CloSURE BACK FRAME REINFoRCES DUCT CUT-oUT

STANDARD AND CUSTOM SIZES AVAILABLE

UL FIRE RATED FLAT ACCESS DOORS

eF

C

AB

BA

D

Door

GasketNOTE: Gasket is High Temp bond-ed to front panel

Optional 4(102 mm) studs for zero clearance duct wrap-order with Suffix (-4)

e-Clip holds back frame to duct for each stude-Clip

wing nuts

**Access Panels over 7 x 7 (178mm x 178mm) have a 1/2 13mm) turndown to add rigidity to the panel. Smaller sizes do not have a turndown.

BackFrame

Flat Access doors uL Fire rated


65X3


D20






Phone No: E-mail:

Additional Notes

DIMENSIONS SIZE INCHES or MMDiMenSiOn EDiMenSiOn F

QUANTITY REQUIRED

PANEL THICKNESS Check One

.050 (1.3mm) S/S Models only

.060 (1.5mm)

.125 (3.2mm)

PANEL MATERIAL Check One

GAlvAnizeD STeel

STAinleSS STeel 304

STAinleSS STeel 316l

MOUNTING HARDWARE MATERIAL

Check One

zinC PlATeD STeelSTAinleSS STeel 304STAinleSS STeel 316l


65X3


FE

Door

GasketNOTE: Gasket is High Temp bonded to front panel

BackFrame

Optional 4(102mm) studs for zero clearance duct wrap order with suffix (-4)

e-Clip holds back frame to duct for each stude-Clip

wing nuts

**Access Panels over 7 x 7 (178mm x 178mm)have a 1/2 (13mm) turndown to add rigidity to the panel. Smaller sizes do not have a turndown.

Order Form-For custom Flat Access door Panels

D21800-526-3694

HI-TEMP ACCESS DOOR IS SOLID, LEAK RESISTANT AND CONSISTS OF TWO LAYERS OF STAMPED,HOT DIPPED GALVANIZED STEEL AND ONE 16 GAUGE BLACK IRON BACKING PLATE

HI-TEMPERATURE CERAMIC FIBER GASKET - RATED 2300F (1260C) MAX-MEETS NFPA 96 STANDARDSIS PERMANENTLY BONDED TO THE OUTSIDE PANEL OF THE ACCESS DOOR TO ELIMINATE LEAKAGE

ZINC PLATED CONICAL SPRINGS ARE INSTALLED, BETWEEN THE INNER AND OUTER PLATES, TO FACILITATE OPENING

ZINC COATED WING NUTS ARE EASILY TURNED BY HAND No MEASURING (SElF-ADHESIvE TEMPlATE PRovIDED)

ACCESS DOORS

MODEL NO. DIMENSIONS CASE QTY

ACC-10X610 x 6

(254mm x 152mm)10

Acc-12x812 x 8

(305mm x 203mm)10

Acc-18x1418 x 14

(457mm x 356mm)4

HI-TEMP ACCESS DOORS

90 VML SERIESSINGLE DEFLECTION MULTI-VALVE DAMPERS

MODEL NO.DUCT SIZE

(AcTuAL HOLE sIZE)CASE QTY

90VML-20x4 20 x 4 (508mm x 102mm) 10

90VML-20x6 20 x 6 (508mm x 152mm) 10

90VML-24x4 24 x 4 (610mm x 102mm) 10

90VML-24x6 24 x 6 (610mm x 152mm) 10

90VML-24x8 24 x 8 (610mm x 203mm) 10

90VML-24x10 24 x 10 (610mm x 254mm) 5

90VML-24x12 24 x 12 (610mm x 305mm) 5

90VML-30X6 30 x 6 (762mm x 152mm) 10

90VML-36X6 36 x 6 (914mm x 152mm) 16

SINGLE DEFLECTION

MULTI-VALVE DAMPERS

ALL MODELS LISTED ARE STOCKED AND READY FOR IMMEDIATE SHIPMENT OTHER SIZES AVAILABLE UPON APPLICATION HORIZONTAL DAMPERS AVAILABLE ON SPECIAL APPLICATION (oN SPECIAl APPlICATIoN oRDERS AlloW TWo WEEKS FoR DElIvERy FRoM RECEIPT oF oRDER) FoR ovERAll DIMENSIoNS ADD 1-3/4 (44mm) TO LISTED WIDTH AND LENGTH

EXTRUDED ANODIZED ALUMINUM TO MATCH STAINLESS STEEL AERODYNAMIC FIN DESIGN

Hi-Temp Access doors & Multi-Valve dampers

ACCESS DOORS WITH 6 MOUNTING STUDSFor Applications using Fire Wrap Insulation

MODEL NO. DIMENSIONS CASE QTY

ACC-10X6-610 x 6

(254mm x 152mm) 6

Acc-12x8-612 x 8

(305mm x 203mm) 6


STAINLESS STEEL CAP STRIPFOr 1/16(1.6mm) MATErIAL

BRIGHT FINISH

MOdEL NO. J63-14517 FT (2.1m) lENGTH

MOdEL NO. J63-1451-88 FT (2.4m) lENGTH


MOdEL NO. J63-1451-1010 FT (3m) lENGTH

STAINLESS STEEL DIVIDER BARW/GALVANIZED BACk PLATE

FOr 1/16(1.6mm) MATErIALBRIGHT FINISH

MOdEL NO. J64-14507 FT (2.1m) lENGTH




EXTENDED LENGTHSTAINLESS STEEL

DIVIDER BARWITH S/S BACk PLATE

FOr 1/16(1.6mm) MATErIALSATIN FINISH

MOdEL NO. J64-1651-786.5 FT (2m) lENGTH


EXTENDED LENGTHSTAINLESS STEEL

CAP STRIPFOr 1/16(1.6mm) MATErIAL

SATIN FINISH

MOdEL NO. J63-1651-786.5 FT (2m) lENGTH


MOULDINGS AND DIVIDERS

7/8(22mm)

5/16(8mm)

REF. A

1-3/8(35mm)

1/2(13mm)

REF. B

7/32(6mm)

A

B

1-1/2(38mm)

7/8(22mm)

REF. C

2-5/32(55mm)7/8

(22mm)

REF. D

7/16(11mm)

C

D

Mouldings, dividers & canopy Hood Grease cups

NEW EXTRA WIDE PROFILE FOR EASIER INSTALLATION ALL STAINLESS STEEL CONSTRUCTION ACCEPTS 1/16 (1.6MM) WAll FlASHING MATERIAl

#4 SATIN FINISH GRAIN OF FINISH MATCHES WALL LINING AvAIlABlE IN 78 AND 120 lENGTHS To MINIMIZE SCRAP INDIVIDUALLY PLASTIC SLEEVED FOR PROTECTION OF FINISH CAP STRIP HAS HEMMED EDGE FOR SAFETY

NICkEL PLATED BRASSCANOPY HOOD DRAINMOdEL NO. F10-1187

DESIGNED FOR DRAINING GREASE FROM TROUGH TO GREASE CUP

SUPPLIED WITH LOCKNUT AND WASHER

FITS 1/2(13mm) I.D. HoSE oR 3/8(9.5mm) O.D. TUBING

9/16(14mm)

1/16(1.6mm)

1/2(13mm O.D.)

15/16(24mm) 1/2 NPS

1 (25mm)

3/8(10mm) I.D.

STAINLESS STEEL kEYHOLE WELD STUDS

MOUNTING KEYHOLE GREASE CUPSMOdEL NO. q37-0250 .430

(11mm)

.282 (7mm).030 (.8mm)

.025 (.6mm) DIA..125 (3mm)

.250 (.6mm)DIA..

See Fabrication Catalog for keyhole welding collets.

REMOVABLE STAINLESS STEEL CANOPY HOOD GREASE CUPS

kEYHOLE MOUNT CUPMOdEL NO. F15-4000

Size: 4 x 6-5/8 x 4 DEEP(102mm x 168mm x 102mm)

4(102mm)

4(102mm)

SIDE MOUNT CUPMOdEL NO. F15-0019

Size: 4-1/4 x 6-3/4 x 2-1/2 DEEP(108mm x 171mm x 64mm)

6-3/4(171mm)

2-1/2(64mm)

4-1/4(108mm)

NSFCOMPONENT

CONFORMS TO NFPA REQUIREMENTS

6-3/4(171mm)

2-1/2(64mm)

4(102mm)

4(102mm)

kEYHOLE MOUNT CUPMOdEL NO. F15-2500-c

Size: 4 x 6-3/4 x 2-1/2 DEEP(102mm x 171mm x 64mm)

REF. B REF. C

REF. A

AB C

10 MOUNTINGANGLE

4(102mm)

6-5/8(168mm)

D23800-526-3694

10.3 oz (305ml) NSF LISTED FDA APPROVED

AVAILABLE IN CLEAR, BRIGHT ALUMINUM, WHITE,BlACK AND RED (HI-TEMP)

FITS ALL STANDARD CAULKING GUNS U.L. RECOGNIZED

MEETS FDA EXTRACTION REQUIREMENTNO. 21 CFR177.2600

FURNISHED WITH REMOVABLE TIP

MODEL NO. COLOR MAX. SERVICE CASE QTY

M90-1010 CLEAR 392F (200C) 10

M90-1012 ALUMINUM 392F (200C) 10

M90-1014 WHITE 392F (200C) 10

M90-1016 BLACK 392F (200C) 10

M90-1018 HI TEMP RED 500F (260C) 10

MASTER CASE QTy: 50

AlSo AvAIlABlE IN 3 oz (85g) TUBES CLEAR: M90-0310 ALUMINUM: M90-0312 WHITE: M90-0314

PACKAGED 20 PER PACK

5 GAlloN (19 liter): MOdEL NO. M90-5012

SILICONE SEALANT

INSULATION HANGERS PROVIDED WITH PEEL AND PLACE ADHESIVE BACKING

ANNEALED COPPER COATED STEEL NAIL

ELIMINATES USING CAPACITOR DISCHARGE NAILS

SUPPLIED WITH GALVANIZED STEEL RETAINING PLATE

Insulation Hangers are made of 2 x 2 (51mm x 51mm) Galvanized Plates with a 1/32(.794mm) white urethane foam

backing which has been coated with a high performance, acrylic based adhesive protected by a release coated liner.

NoTE: oTHER lENGTHS AvAIlABlE UPoN REQUEST

MODEL NO. HANGER LENGTH CASE QTY

q86-1000 1 (25mm) 1000

q86-1250 1-1/4 (32mm) 1000

q86-1500 1-1/2 (38mm) 1000

q86-1625 1-5/8 (41mm) 1000

q86-2000 2 (51mm) 1000

MODEL NO. PIN SIZE CASE QTY

q86-0010 12 GA. x 1(25mm) 1000

q86-0015 12 GA. x 1-1/2(38mm) 1000

q86-0020 12 GA. x 2(51mm) 1000

RETAINING PLATE

q86-0001 1 x 1-1/4 (32mm) 1000

INSULATION WELD PINS ANNEALED COPPER COATED STEEL NAIL CD TYPE

GALVANIZED STEEL RETAINING PLATE AVAILABLE

FOIL AND DUCT TAPE IDEAL FOR SEALING SEAMS AND JOINTS ON HVAC DUCTS

REF. MODEL NO. TYPE SIZE CASE QTY

A q84-3200 HEAVY DUTY DUCT TAPE2 x 60 yDS

(51mm x 55m)24

B q84-4250HI-STRENGTH

ALUMINUM FOIL TAPE2-1/2 x 50 yDS (64mm x 46m)

16

A.

B.

File No. E224060

NSFCOMPONENT

sealant, caulking Gun, Tape, Insulation Hangers & Weld Pins

3oz Tube

CAULkING GUNFor Use With

10.3 oz (305ml) Cartridge

MODEL NO. Q99-1000


MODEL NO. DESCRIPTION NET CONTENTBOX/CASE

QTY

q85-2004 (shown) Pump Spray 4 fl. oz. (118ml) Each

q85-200424 Pump Spray 4 fl. oz. (118ml) 24/Box

q85-2016 (shown) Pump Spray 16 fl. oz. (474ml) Each

q85-201606 Pump Spray 16 fl. oz. (474ml) 6/Box

q85-201612 Pump Spray 16 fl. oz. (474ml) 12/Case

MODEL NO. DESCRIPTION NET CONTENT BOX QTY

q85-2128 (shown) Refill 1 gal. (3.8ml) Each

q85-212804 Refill 1 gal. (3.8ml) 4/Box

Brite Gard

CLEANS, SHINES & PROTECTS

DOES NOT LEAVE OILY RESIDUE

ENvIRoNMENTAlly FRIENDly USES MANUAlPUMP SPRAYER, NOT AEROSOLS

VIRTUALLY ELIMINATES FINGERPRINTS & SMUDGES

SPECIFICALLY FORMULATED FOR USE ON INDooR/oUTDooR STAINlESS STEEl APPlIANCES

SAFE USES FooD GRADE INGREDIENTS

MODEL NO.Q85-2128

Biodegradable100% Recyclable

MODEL NO.Q85-2016MODEL NO.

Q85-2004

Brite Gard cleaning Products

HEAVY-WEIGHT quArTErFOLd (60 Count)

MOdEL NO. q85-7000

LIGHT-WEIGHT quArTErFOLd (90 Count)

MOdEL NO. q85-7500

SUPER STRENGTH INTERFOLD (126 Count)

MOdEL NO. q85-8000

LIGHT-WEIGHT INTErFOLd (135 Count)

MOdEL NO. q85-8500

Sheet Size:12-1/2 x 13

(138mm x330mm)Sheet Size:

12-1/2 x 13 (138mm x 330mm)

Sheet Size:9-1/2 x 16-1/2

(241mm x419mm)Sheet Size:

9-1/2 x 16-1/2 (241mm x419mm)

Sheet Per Case: 720 Sheet Per Case: 1080 Sheet Per Case: 1008 Sheet Per Case: 1080

Case Quantity: 12 Case Quantity: 12 Case Quantity: 8 Case Quantity: 8

Case Weight: 15lbs (7kg) Case Weight: 15lbs (7kg) Case Weight: 18lbs (8kg) Case Weight: 20lbs (9kg)

wipers Contain

25%recycled Fibers

go greenCHG

MADE WITH 25% RECyClED CEllUloSE FIBERS

PERFECT FoR HEAvy DUTy WET/DRy WIPING APPlICATIoNS

IDEAL FOR MOST METAL WORKING AND MESSY FLUID APPLICATIONS

INTERFOLDS ARE PERFECT FOR JOBS THAT REQUIRE LARGE WIPERSS

TWO TIMES STRONGER THAN THE COMPETITION

COST EFFECTIVE ALTERNATIVE TO CLOTH TOWELS & RAGS

LOW LINT

MODEL NO.Q85-7000Q85-7500

MODEL NO. Q85-8000Q85-8500

Brite GardALL PURPOSE WIPERS

STAINLESS STEELCLEANER/PROTECTANT

D25800-526-3694

Index

101016 D1101020 D1101216 D1101218 D1101220 D1101224 D1101616 D1101620 D1101625 D1102010 D1102016 D1102020 D1102025 D1102516 D1102520 D1151016 D1151020 D1151216 D1151218 D1151220 D1151224 D1151616 D1151620 D1151625 D1152010 D1152016 D1152020 D1152025 D1152516 D1152520 D1201016 D2201020 D2201216 D2201220 D2201616 D2201620 D2201625 D2202016 D2202020 D2202025 D2202516 D22025 20 D2300001 D2,D3301016 D2301020 D2301216 D2301220 D2301616 D2301620 D2301625 D2301818 D2302016 D2302020 D2302025 D2302516 D2302520 D2451016 D3451020 D3451216 D3451220 D3451616 D3451620 D3451625 D3452016 D3

452020 D3452025 D3452516 D3452520 D3551016 D3551020 D3551216 D3551220 D3551616 D3551620 D3551625 D3552016 D3552020 D3552025 D3552516 D3552520 D3750002 D15750505-C D16, D17750511-C D16, D17750517-C D16, D17750606 D19750707 D19750710 D19750712 D19750715 D19750720 D19750723 D19750808-C D16, D17750811-C D16, D17750817-C D16, D17750823-C D16, D17751117-C D16, D17751123-C D16, D17751212 D19751220 D19751620 D19751717-C D16, D17751723-C D16, D17752020 D1990VML-20X4 D2190VML-20X6 D2190VML-24X10 D2190VML-24X12 D2190VML-24X4 D2190VML-24X6 D2190VML-24X8 D2190VML-30X6 D2190VML-36X6 D21ACC-10X6 D21ACC-12X8 D21ACC-18X14 D21ACC-10X6-6 D21ACC-12X8-6 D21F10-1187 D22F11-0014 D14, D15F11-0038 D14, D15F11-0038A D14, D15F11-0012 D14, D15F11-0012A D14F11-0012B D14F11-0034 D14, D15F11-0100 D14, D15F11-0114 D14, D15F11-0112 D14, D15

F12-0034 D14F12-0078 D14F12-0118 D14F12-0138 D14F12-0158 D14F15-0019 D22F15-2500-C D22F15-4000 D22F40-0002 D4,D9F40-1020 D10F40-1620 D10F40-1625 D10F40-2020 D10F40-2025 D10F41-0001 D10F41-1020 D10F41-1620 D10F41-1625 D10F41-2020 D10F41-2025 D10FA30-1016-HD D4FA30-1020-HD D4FA30-1216-HD D4FA30-1220-HD D4FA30-1616-HD D4FA30-1620-HD D4FA30-1625-HD D4FA30-2016-HD D4FA30-2020-HD D4FA30-2025-HD D4FA30-2520-HD D4FG20-500500 D3FG20-500400 D3FG20-400400 D3FG20-400500 D3FG20-500300 D3FG20-300500 D3FG20-495495 D3FG35-1016-HD D4FG35-1020-HD D4FG35-1216-HD D4FG35-1220-HD D4FG35-1616-HD D4FG35-1620-HD D4FG35-1625-HD D4FG35-2016-HD D4FG35-2020-HD D4FG35-2025-HD D4FG35-2516-HD D4FG35-2520-HD D4FS50-1016-BA D4FS50-1020-BA D4FS50-1216-BA D4FS50-1220-BA D4FS50-1616-BA D4FS50-1620-BA D4FS50-1625-BA D4FS50-2016-BA D4FS50-2020-BA D4FS50-2025-BA D4FS50-2516-BA D4FS50-2520-BA D4J63-1451 D22J63-1451-8 D22

J63-1451-9 D22J63-1451-10 D22J63-1651-78 D22J63-1651-120 D22J64-1450 D22J64-1450-8 D22J64-1450-9 D22J64-1450-10 D22J64-1651-78 D22J64-1651-120 D22L10-X020 D12L50-X009 D12L50-X011 D12L50-Y001 D12L55-1004 D11L55-1004-CSA D11L55-1004-HT D11L55-1024 D11L55-1024-CSA D11L55-1024-HT D11L55-2004 D11L55-2004-CSA D11L55-2004-HT D11L55-2024 D11L55-2024-CSA D11L55-2024-HT D11L55-X003 D12L55-X003-HT D12L55-X006 D12L55-X022 D12L55-Y001 D12L55-Y001-CSA D12L55-Y001-HT D12L82-1020 D13L82-1030 D13L82-1040 D13L87-1004 D13M90-0310 D23M90-0312 D23M90-0314 D23M90-1010 D23M90-1012 D23M90-1014 D23M90-1016 D23M90-1018 D23M90-5012 D23MCD 116 D1MCD 116-1.5 D1MCD 120 D1MCD 120-1.5 D1MCD 123 D1MCD 126 D1MCD 128 D1MCD 133 D1MCD 136 D1MCD 139 D1Q37-0250 D22Q84-3200 D23Q84-4250 D23Q85-2004 D24Q85-200424 D24Q85-2016 D24Q85-201606 D24Q85-201612 D24

MODEL NO. PAGE NO. MODEL NO. PAGE NO. MODEL NO. PAGE NO. MODEL NO. PAGE NO.


Index

Q85-2128 D24Q85-212804 D24Q85-7000 D24Q85-7500 D24Q85-8000 D24Q85-8500 D24Q86-0001 D23Q86-0010 D23Q86-0015 D23Q86-0020 D23Q86-1000 D23Q86-1250 D23Q86-1500 D23Q86-1625 D23Q86-2000 D23Q99-1000 D23TYPE I D1, D5, D6TYPE II D2, D6, D7TYPE III D2, D3, D8TYPE IV D3, D9TYPE V D4, D9, D10

MODEL NO. PAGE NO. MODEL NO. PAGE NO. MODEL NO. PAGE NO. MODEL NO. PAGE NO.

1890 Swarthmore Avenue PO Box 2020 Lakewood NJ 08701 Tel. 800-526-3694 732-363-4700 Fax 732-364-8110

www.flamegard.com

If youre not using Flame Gard,

GRILL AT YOUR OWN RISK.

Pages from CAT-X024_COOKING HOOD_2011COOKING HOOD_2011ACOOKING HOOD_2011Pages from CAT-X024_COOKING HOOD_2011lastCAT-X024_COOKING HOOD_2011-2

Documents

Cat-x024 Cooking-hood 5 2012