43
Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the Caterpillar TOPS Data Book, 07/12/2013. Offeror shall price these complete trucks in their entirety, on Form-D, reflecting the entire complement of the base vehicle specification's standard features listed herein, as well as all normal dealer make-ready and factory-to-dealer destination charges. Except as ordered by an H-GAC member (e.g. axle upgrade, longer wheelbase, et cetera), the base units described herein and priced on Form-D shall not require any additional compulsory components, fees, or services to render them complete, functional, and legal cab-chassis. H-GAC Product Code: B1 CT660S-STA, TRA, 116” BBC (CF7AA), Truck Configuration Model Profile 2015 CT660S SBA 6x4 (CF7AA) APPLICATION: Utility/Service (Other) MISSION: Requested GVWR: 52300. Calc. GVWR: 52350 Calc. Start / Grade Ability: 29.30% / 2.48% @ 55 MPH Calc. Geared Speed: 79.0 MPH FUEL ECONOMY: 7.65 MPG @ 55 MPH DIMENSION: Wheelbase: 177.00, CA: 115.00, Axle to Frame: 53.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 365 HP @ 1700 RPM, 1250 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 365 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FRO-12210C} 10-Speed Manual, With Overdrive, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 4.33 CAB: Conventional TIRE, FRONT: (2) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply TIRE, REAR: (8) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KT Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description CF7AA00 Base Chassis, Model CT660S SBA 6x4 with 177.00 Wheelbase, 115.00 CA, and 53.00 Axle to Frame. 1652 CROSSMEMBER, REAR Relocated to End of Frame 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 1LBC BUMPER, FRONT Multi-piece Stainless Steel Includes : FOG LIGHT OPENING (2) and with Rectangular Hole for Step 1WVR WHEELBASE RANGE 138" (350cm) Through and Including 181" (460cm) 2ASG AXLE, FRONT NON-DRIVING {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity 3ACH SUSPENSION, FRONT, SPRING Multileaf, Shackle Type; 14,000-lb Capacity; With Shock Absorbers Includes : SPRING PINS Threaded 4091 BRAKE SYSTEM, AIR Dual System for Straight Truck Applications Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : DUST SHIELDS, FRONT BRAKE : DUST SHIELDS, REAR BRAKE : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : INVERSION VALVE Bendix SR-1 and Double Check Valve : PARKING BRAKE CONTROL Yellow Knob, Located on Instrument Panel : PARKING BRAKE VALVE For Truck : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for 4x2, 2 for 6x4 : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic

Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

  • Upload
    others

  • View
    5

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Caterpillar Standard Features Bid Invitation #HT06-14

The following descriptions are the standard features, as pulled from the Caterpillar TOPS Data Book, 07/12/2013. Offeror shall price these complete trucks in their entirety, on Form-D, reflecting the entire complement of the base vehicle specification's standard features listed herein, as well as all normal dealer make-ready and factory-to-dealer destination charges. Except as ordered by an H-GAC member (e.g. axle upgrade, longer wheelbase, et cetera), the base units described herein and priced on Form-D shall not require any additional compulsory components, fees, or services to render them complete, functional, and legal cab-chassis.

H-GAC Product Code: B1 CT660S-STA, TRA, 116” BBC (CF7AA), Truck Configuration

Model Profile 2015 CT660S SBA 6x4 (CF7AA) APPLICATION: Utility/Service (Other) MISSION: Requested GVWR: 52300. Calc. GVWR: 52350 Calc. Start / Grade Ability: 29.30% / 2.48% @ 55 MPH Calc. Geared Speed: 79.0 MPH FUEL ECONOMY: 7.65 MPG @ 55 MPH DIMENSION: Wheelbase: 177.00, CA: 115.00, Axle to Frame: 53.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 365 HP @ 1700 RPM, 1250 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 365 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FRO-12210C} 10-Speed Manual, With Overdrive, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 4.33 CAB: Conventional TIRE, FRONT: (2) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply TIRE, REAR: (8) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KT Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description CF7AA00 Base Chassis, Model CT660S SBA 6x4 with 177.00 Wheelbase, 115.00 CA, and 53.00 Axle to Frame. 1652 CROSSMEMBER, REAR Relocated to End of Frame 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 1LBC BUMPER, FRONT Multi-piece Stainless Steel Includes : FOG LIGHT OPENING (2) and with Rectangular Hole for Step 1WVR WHEELBASE RANGE 138" (350cm) Through and Including 181" (460cm) 2ASG AXLE, FRONT NON-DRIVING {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity 3ACH SUSPENSION, FRONT, SPRING Multileaf, Shackle Type; 14,000-lb Capacity; With Shock Absorbers Includes : SPRING PINS Threaded 4091 BRAKE SYSTEM, AIR Dual System for Straight Truck Applications Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : DUST SHIELDS, FRONT BRAKE : DUST SHIELDS, REAR BRAKE : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : INVERSION VALVE Bendix SR-1 and Double Check Valve : PARKING BRAKE CONTROL Yellow Knob, Located on Instrument Panel : PARKING BRAKE VALVE For Truck : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for 4x2, 2 for 6x4 : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic

Page 2: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

: SWITCH, AUXILIARY Interrupter for Cab Clearance/Marker Lights (Blinks Lights with Headlight Switch in "ON" Position); Instrument Panel Mounted Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4193 BRAKES, FRONT, AIR CAM 16.5" x 6", Includes 24 SqIn Long Stroke Brake Chambers 4619 TRAILER CONNECTIONS Four-Wheel, With Hand Control Valve and Tractor Protection Valve, for Straight Truck Includes : INVERSION VALVE Bendix SR-1 and Double Check Valve 4732 DRAIN VALVE {Berg} Manual; With Pull Chain, for Air Tank Includes : DRAIN VALVE Mounted in Wet Tank 4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel) 4EBS AIR DRYER {Bendix AD-9} With Heater Includes : AIR DRYER LOCATION Inside Left Rail, Back of Cab 4ETE BRAKE CHAMBERS, FRONT AXLE {Haldex} 24 SqIn 4EVL BRAKE CHAMBERS, REAR AXLE {Haldex GC3030LHDHO} 30/30 Spring Brake Code Description 4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.In. Long Stroke Brake Chamber and Spring Actuated Parking Brake 4SPM AIR COMPRESSOR {Bendix BA-921 Head Unload} 15.9 CFM Capacity, Single Cylinder 4WCC BRAKE PACKAGE, FRONT {Dana Spicer ES-165-6} Air, Cam Type, Extended Service; Size 16.5" x 6", Includes Automatic Slack Adjusters 4WCD BRAKE PACKAGE, REAR {Dana Spicer ES-165-7} Air, Cam Type, Extended Service; Size 16.5" x 7", Includes Automatic Slack Adjusters 5710 STEERING COLUMN Tilting and Telescoping 5PSA STEERING GEAR {Sheppard M-100} Power 5WBH STEERING WHEEL {Caterpillar} 2-Spoke, 18" Diam., Dark Neutral, Leather Wrapped 7BJU EXHAUST SYSTEM Switchback Horizontal Aftertreatment Device, Frame Mounted Right Side Under Cab; Includes Single Vertical Tail Pipe & Guard, Right Side, Cab Mounted 8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment Includes : BATTERY BOX Aluminum : CIGAR LIGHTER Includes Ash Cup, Center Console Mounted : FUSES, ELECTRICAL SAE Blade-Type : HAZARD SWITCH Integral with Turn Signal Switch : HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever : HEADLIGHTS (2) Composite with Halogen Projector Beam : HORN, AIR Single, Chrome : HORN, ELECTRIC Single : PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light : READING LIGHT, CAB (2) with Individual Switches; One Above Each Door : STARTER SWITCH Electric, Key Operated : STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector : TURN SIGNAL FLASHER : TURN SIGNAL SWITCH Manual Cancelling with Lane Change Feature : TURN SIGNALS, FRONT Includes Integral Reflectors and Side Marker Lights; Fender Mounted : WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature, Steering Column Mounted : WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted : WIRING, CHASSIS Color Coded and Continuously Numbered 8554 TRAILER CONNECTION SOCKET 7-Way; Mounted at Rear of Frame 8653 HORN, AIR Single, Located Under Cab 8718 POWER SOURCE Cigar Type Receptacle without Plug and Cord 8GGN ALTERNATOR {Bosch LH160} Brush Type, 12 Volt 160 Amp. Capacity, Pad Mount 8MMJ BATTERY SYSTEM {Caterpillar} (3) 12 Volt 2130CCA Total 8RMD RADIO AM/FM/WB/Clock/3MM Auxiliary Input, with Multiple Speakers 8RMG ANTENNA BASE (2) Single Function, (1) for CB and (1) for Entertainment Radio, Without Splitter, Separate Lead-Ins, With CB Antenna Mounted on Left Mirror and AM/FM Antenna Mounted on Right Mirror 8WCK POWER SOURCE, TERMINAL TYPE 2-Post 8WEZ TURN SIGNAL SWITCH Self-Canceling 8WKH BATTERY BOX Aluminum with Aluminum Cover, 18" Wide, 2, 3 or 4 Battery Capacity, Mounted Right Side Back of Cab 8WNH RUNNING LIGHT (2) Daytime Code Description 8WXG STARTING MOTOR {Mitsubishi Electric Automotive America 105P} 12-Volt, with Soft-Start 9ASE FRONT END Tilting Composite Includes

Page 3: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

: GRILLE SURROUND Brushed Stainless Steel 9HAN INSULATION, UNDER HOOD for Sound Abatement 9HBN INSULATION, SPLASH PANELS for Sound Abatement 10060 PAINT SCHEMATIC, PT-1 Single Color, Design 100 10761 PAINT TYPE Base Coat/Clear Coat, 1-2 Tone 10769 PAINT CLASS Premium Color 11MGZ CLUTCH {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity Includes : CLUTCH RELEASE BEARING Greasable 12KXL ENGINE, DIESEL {CT 13} EPA 10, SCR, 365 HP @ 1700 RPM, 1250 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 365 Peak HP (Max) 12THT FAN DRIVE {Horton Drivemaster} Direct Drive Type, Two Speed With Residual Torque Device for Disengaged Fan Speed 12UBH RADIATOR Aluminum; Welded, Front to Back Down Flow System, 1564 SqIn, 1572 SqIn Dual CAC, 1293 SqIn 3 Core LTR 12VBT AIR CLEANER Single Element, Heavy Duty 12VED FEDERAL EMISSIONS for 2010; CT 13 Engines 12WCX HOSE CLAMPS, RADIATOR HOSES {Gates} Shrink Band Type 12WEG COLD STARTING EQUIPMENT Automatic; With Engine ECM Control 12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, Engine Mounted 12WZJ EMISSION COMPLIANCE Low NOx Idle Engine, Complies with California Clean Air Regulations; Includes "Certified Clean Idle" Decal located on Driver Door 12XAN OBD COMPLIANCE for 2013 OBD (On Board Diagnostics) 13GGV TRANSMISSION, MANUAL {Fuller FRO-12210C} 10-Speed Manual, With Overdrive, With Air Shift Includes : CLUTCH BRAKE Torque Limiting : FILL PLUG, MAGNETIC 13WLB TRANSMISSION OIL {EmGard 50W} Synthetic; 22 thru 33.99 Pints 14GVU AXLE, REAR, TANDEM {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Lube Oil Pump . Gear Ratio: 4.33 Includes : POWER DIVIDER LOCK Air Operated, Cab Control with Indicator Light in Cluster : REAR AXLE DRAIN PLUG (2) Magnetic, For Tandem Rear Axle 14ULX SUSPENSION, REAR, TANDEM {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000- lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers Includes : CROSSMEMBER, SUSPENSION Stamped Steel Double Dogbone Code Description Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 14WAL SUSPENSION/REAR-AXLE IDENTITY for Meritor Tandem Rear Axles With Bar-Pin Beam Attachment Type Suspensions 14WBV SHOCK ABSORBERS, REAR (4) for Hendrickson HMX Suspension Only, Mounted from Frame to Beam 14WLD AXLE, REAR, LUBE {EmGard 75W-90} Synthetic Oil; 50 thru 64.99 Pints 15DYP DEF TANK 9.5 U.S. Gal. 36.0L Capacity, Frame Mounted Outside Left Rail, Under Cab 15LKU FUEL/WATER SEPARATOR {Racor} Fuel Pre-Filter and Filter Base, Includes Water-In-Fuel Sensor 15SJZ FUEL TANK Top Draw; Non-Polished Aluminum, 26" Diam., 80 U.S. Gal., 302 L Capacity Mounted Left Side, Under Cab 16031 CAB Conventional Includes : COAT HOOK, CAB Located on Rear Wall, Behind Passenger Seat : CONSOLE, CENTER Plastic, Driver Convenience with a Cup and Change Holder, Ash Tray and Lower Storage Area : DOME LIGHT, CAB (2) Driver and Passenger Dome Lights with Individual Switches, in Headliner : DOOR CHECK STRAP (2) One Each Door : GLASS, ALL WINDOWS Tinted : GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side : GRAB HANDLE, EXTERIOR (2) Mounted Behind Driver and Passenger Doors : INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color : SKIN Riveted : STEP (4) Two Steps Per Door 16400 SEAT, PASSENGER Omit Item 16HBA GAUGE CLUSTER English With English Electronic Speedometer 16JPC SEAT, DRIVER {National 2000 Model 295} Air Suspension, Intermediate Back, All Vinyl, 2 Arm Rests, Isolator, 7" Adjuster, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, 3 Position Rear Cushion, 2-15 Degree Back Angle Adjust, Vinyl Suspension Cover 16SKS MIRRORS (2) {Lang Mekra} Aero; Rectangular, 7.09" x 15.75" & Integral Convex Both Sides, 102" Inside

Page 4: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Spacing, Breakaway Type, Heated Heads Thermostat Controlled, Amber Lens Clearance Light LED, Black Painted Finish Heads, Brackets & Arms 16VRT HEATER, ENHANCED CIRCULATION {Bergstrom} Control, for Extreme Cold Weather Climates 16VTH CAB INTERIOR TRIM Premium Level; for Caterpillar, Day Cab Includes : "A" PILLAR COVER Molded Plastic : CAB INTERIOR TRIM PANELS Vinyl : CONSOLE, OVERHEAD Molded Plastic with Three Storage Pockets; One with Strap for CB Radio Mounting; Two with Netting, Courtesy Lights with Switches : COURTESY LIGHT (2) Driver and Passenger Door Mounted : DOOR TRIM PANELS Vinyl Upper with Power Locks and Windows, Upper and Lower Grab Handles, Both Sides : FLOOR COVERING Rubber, Black : HEADLINER Soft Padded Vinyl : HEATER BOX Metal, Painted Black : INSTRUMENT PANEL TRIM Vinyl : MIRROR, CONVEX, LOOK DOWN Black Finish; 6" x 10-1/4"; Located on Passenger Side : STORAGE POCKET, DOOR (2) Driver and Passenger Door Code Description : SUN VISOR (2) Vinyl with Molded Toll Ticket Retainer 16VZA WINDOW, REAR 52.25" Wide 16WAK WINDOW, POWER (2) in Left and Right Doors 16WJG CAB DOOR LOCKS Power 16WKB AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster 16WKR WINDSHIELD Single Piece 16WLD CAB REAR SUSPENSION {Link Z9079D1} Dual Frame Mounted Cab Rear Air Suspension; Includes Special Crossmember Assembly 16XWD SUNSHADE, EXTERIOR Aerodynamic, Painted Roof Color; Includes Integral Clearance/Marker Lights 27DMA WHEELS, FRONT DISC; 22.5" Painted Steel, 2 Hand Hole, 10 Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs Includes : PAINT IDENTITY, FRONT WHEELS White 28DMA WHEELS, REAR DUAL DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs Includes : PAINT IDENTITY, REAR WHEELS White 7372135415 (2) TIRE, FRONT 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply 7372135415 (8) TIRE, REAR 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply Graphics are provided as visual aids only and are not intended to represent the actual scale, shape, or color of the truck or its components. All weights are represented in lbs. Truck Body/Trailer Chassis/Empty Weights Bumper to Axle (BA) 54.0 Wheelbase (WB)177.00 Axle to Frame (AF) 53.00 Axle to Back Cab (ABC) 62 Cab to Axle (CA) 115 Usable CA 115 CA Reduction Adjustment 0 Fuel-Diesel(Gals) 50 DEF(Gals) 0 Body Length (BL) 258 Tractor Front Axle: 9,575 Tractor Rear Axle: 6,804 Payloads Before the Cab Cab Chassis Body After the Body # Weight CG # Weight CG # Weight CG # Weight CG # Weight CG 1 23,500 82 Loads Weight Distribution Payload Weight: 23,500 Driver: 250 Fuel-Diesel(Lbs): 355 DEF(Lbs): 0 Total Front Axle: 13,444 Total Rear Axle: 32,040 Total Weight: 45,484 Weights and clearances in this proposal are estimates only. Neither Caterpillar nor its suppliers are liable for any consequences resulting from any differences between the estimated weights and clearances and the actual manufactured weights and clearances. Weight Distribution

Page 5: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

All weights are represented in lbs. Truck Front Rear Total Chassis Weight Chassis Weight: 9,575 6,804 16,379 Fuel: 178 177 355 DEF: 0 0 0 Empty Body: -480 5,480 5,000 (Curb Weight): 9,273 12,461 21,734 Loads Payloads: 3,983 19,517 23,500 Driver: 188 62 250 Axle Totals (Gross Weight): 13,444 32,040 45,484 Weight Ratings Truck Front Rear Axle(axle capacity) 13,200 40,000 Tire(tire capacity) 12,350 46,720 Suspension(suspension capacity) 14,000 40,000 Spring: 0 Fed Bridge Law (axle spread): 20,000 34,000 (54") Wheel Combination Load Limit 1 - 3 45,484 48,500 Federal Total Vehicle Weight Limit: 80,000 Maximum Gross Vehicle Weight Rating (GVWR) 52,350 - Gross Vehicle Weight(GVW) 45,484 = 6,866 Reserves Weight Summary * Front Tractor - Axle Weight exceeds Axle capacity ENGINE, DIESEL (0012KXL) ATTACHMENTS: 0016HBA (GAUGE CLUSTER) 0015LKU (FUEL/WATER SEPARATOR) 0012WEG (COLD STARTING EQUIPMENT) 0012THT (FAN DRIVE) Parameter Value UOM Max Accelerator Vehicle Speed:7902 79 MPH Vehicle Speed Limiter Override:7911 0, DISABLE FEATURE OR FUNCTION N/A VSLO Speed Increment:7912 10 MPH VSLO Maximum Activation Time:7914 30 MIN VSLO Time Interval to Reset:7915 8.0 HOURS VSLO Time Duration Source:7934 1, INTERVAL BASED ON REAL TIME CLOCK N/A Progressive Shift Enable:7744 0, DISABLE FEATURE OR FUNCTION N/A Low Gear Ratio Break Point:7742 5.825000 N/A High Gear Ratio Break Point:7743 1.643500000 N/A Low Gear Engine Speed Limit:7738 1550.0 RPM High Gear Engine Speed Limit:7739 1600.0 RPM Low Gear Engine Speed Range:7740 200.0 RPM High Gear Engine Speed Range:7741 200.0 RPM Min Gear Ratio for ProShift:7755 0.50 N/A Gear Down Protection Enable:7714 0, DISABLE FEATURE OR FUNCTION N/A Top Gr Minus 2 Light Ld VS Lim:7715 31 MPH Top Gr Minus 1 Light Ld VS Lim:7716 41 MPH Top Gr Minus 2 Heavy Ld VS Lim:7735 33 MPH Top Gr Minus 1 Heavy Ld VS Lim:7736 46 MPH Driver Reward Enable:7918 0, DISABLE FEATURE OR FUNCTION N/A Driver Reward Mode:7930 2, BOTH ACCELERATOR AND CRUISE VEHICLE SPEED LIMIT INCREASE N/A Driver Reward Performance Crit:7925 0, FUEL ECONOMY BASED REWARD SYSEM N/A Fuel Economy - Expected Level:7921 6.00 MPG Fuel Economy - Good Level:7920 6.25 MPG Fuel Economy - Excellent Level:7919 6.40 MPG % Idle Time - Expected Level:7924 25 % % Idle Time - Good Level:7923 18 % % Idle Time - Excellent Level:7922 10 % Driver Reward Ambient Temp H:7938 150.0 C Driver Reward Ambient Temp L:7939 -40.0 C VS Lim Increase - Expected Lvl:7926 0 MPH VS Lim Increase - Good Lvl:7927 2 MPH VS Lim Increase - Excel Lvl:7928 4 MPH VS Lim Decrease - Penalty Lvl:7929 -2 MPH Idle Engine Speed:8202 600.0 RPM

Page 6: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Idle Speed Adjustment Enable:8215 1, ENABLE FEATURE OR FUNCTION N/A Idle Spd Adjust - Max Eng Spd:8212 0.0 RPM Idle Spd Adjust - Bump Step:8216 5.0 RPM Idle Spd Adjust Ramp Rate:8211 25 RPM/SEC Maximum Standstill Eng Speed:7753 2100.0 RPM Idle Shutdown Mode:7400 0, DISABLE FEATURE OR FUNCTION N/A ISD Time w/Park Brk Released:7401 15.0 MIN ISD Time w/Park Brake Set:7404 5.0 MIN ISD Latched Driver Override En:7407 0, DISABLE FEATURE OR FUNCTION N/A ISD Ambient Temp Override En:7408 0, DISABLE FEATURE OR FUNCTION N/A ISD Int Amb Temp Enable:7405 0, DISABLE FEATURE OR FUNCTION N/A ISD Max Ambient Temp Override:7402 20.0 C ISD Int Amb Temp Override:7406 15.0 C ISD Min Ambient Temp Override:7403 5.0 C ISD Max Engine Coolant Temp:7412 150.0 C ISD Min Engine Coolant Temp:7413 16.0 C ISD Idle Shutdown Max Eng Trq:7409 80 % Cruise Control Enable:7600 1, ENABLE FEATURE OR FUNCTION N/A Electronic Parameters CC Max Vehicle Speed:7604 79 MPH CC Min Vehicle Speed:7603 25.0000 MPH AESC Control:7500 0, DISABLE FEATURE OR FUNCTION N/A AESC In-cab Mode:7502 2, VARIABLE ENGINE SPEED CONTROL SELECTED N/A AESC Min Engine Speed:7522 600.0 RPM AESC Max Engine Speed:7508 1500.0 RPM AESC Preset Engine Speed 1:7505 800.0 RPM AESC Preset Engine Speed 2:7506 900.0 RPM AESC Preset Engine Speed 3:7514 1000.0 RPM AESC Preset Engine Speed 4:7515 1100.0 RPM AESC Preset Engine Speed 5:7516 1200.0 RPM AESC Preset Engine Speed 6:7517 1300.0 RPM AESC Activate at Preset Speed:7528 0, NO PRESET PRESELECTION N/A AESC Ramp Up Rate:7507 100.00 RPM/SEC AESC Ramp Down Rate:7524 100.00 RPM/SEC AESC Bump Up/Down Step:7525 25.0 RPM AESC In-cab Operator Interface:7503 0, NO (OFF) OR DISABLE N/A AESC Disable w/ Clutch Pedal:7510 1, ENABLE FEATURE OR FUNCTION N/A AESC Disable w/ Brake Pedal:7511 1, ENABLE FEATURE OR FUNCTION N/A AESC Accel Pedal Mode:7513 1, AESC OVERRIDDEN BY ACCELERATOR PEDAL N/A AESC Max Engine Load:7519 100.0000 % AESC Control to Engine Load:7530 0, KICK OUT OF AESC ABOVE PROGRAMMED LIMIT N/A AESC Max Engine Load Time:7527 8 SEC AESC Vehicle Speed Limit:7521 5.0000 MPH AESC Max Mobile Veh Spd:7501 5 MPH AESC Eng Spd Limit w/VSS Fault:7518 1500 RPM AESC Force Fan On:9007 0, DISABLE FEATURE OR FUNCTION N/A AESC Park Brake Override:7534 1, ENABLE FEATURE OR FUNCTION N/A AESC Transfer Case Signal Mode:8910 0, DRIVELINE N/A AESC Splitshaft Veh SPD Dsply:9307 0, SPEED SENSOR LOCATED IN WHEEL RIM N/A AESC Remote Accel Pedal Enable:7504 0, DISABLE FEATURE OR FUNCTION N/A AESC Remote Accel Pedal Switch:8914 0, DISABLE FEATURE OR FUNCTION N/A AESC Accel Max Eng Spd Ovrd:7520 1900.0 RPM Rem Accelerator Switch Input:9929 1, SAE J1939 MULTIPLEXED N/A Preset Remote AESC Input Type:9932 0, DISCRETE (HARDWIRED) INPUT N/A Variable Remote AESC Input:9933 0, DISCRETE (HARDWIRED) INPUT N/A Rem Accelerator Position Input:9935 1, SAE J1939 MULTIPLEXED N/A Engine Protection Mode:7700 1, TWO WAY WARNING (OIL PRES, WATER TEMP) N/A Powertrain Protection Enable:7722 0, DISABLE FEATURE OR FUNCTION N/A Torque Limiting in Gear:7717 0, DISABLE FEATURE OR FUNCTION N/A Highest Gear of Low Range:7718 2 N/A Highest Gear Rat of Low Range:7745 6.00 N/A Highest Gear of Int. Range:7748 4 N/A Highest Gear Rat of Int. Range:7746 4.00 N/A Highest Gear of High Range:7749 6 N/A Highest Gear Rat of High Range:7747 2.00 N/A Max Torque in Low Gear Range:7713 1250.0000 LB-FT Max Torque in Int. Gear Range:7750 1250.0000 LB-FT Max Torque in High Gear Range:7751 1250.0000 LB-FT VSS Anti-Tamper Max Eng Speed:7901 1410.0 RPM

Page 7: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Auxilllary Shutdown Input Type:9931 0, DISCRETE (HARDWIRED) INPUT N/A Veh Speed Sensor Antitampering:7905 0, DISABLE FEATURE OR FUNCTION N/A Veh Overspd Threshold Level 1:7723 84.462626 MPH Veh Overspd Threshold Level 2:7724 86.462626 MPH Service Interval Enable 0, DISABLE FEATURE OR FUNCTION N/A Fuel Used Service Interval:9501 0 GALLONS Engine Hour Service Interval:9502 0 HOURS Veh Distance Service Interval:9503 0 MILES Service Soon Percent to Notify:9507 90 % Customer Unit Number:6605 0 N/A Hard Braking Incident Counter:8904 1, ENABLE FEATURE OR FUNCTION N/A Hard Braking Decel Threshold:8905 7.40 MPH/SEC Vehicle Over-speed Indicator:7754 0, FEATURE OR FUNCTION IS DISABLED N/A Customer Password:8700 00000000 N/A These Electronic Parameters have not been finalized

Page 8: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

H-GAC Product Code: B2 CT660S-STA, TRA, 116” BBC (CF7AA), Tractor Configuration

Model Profile 2015 CT660S SBA 6x4 (CF7AA) APPLICATION: On-Off Highway Tractor - General MISSION: Requested GCWR: 80000. Calc. GVWR: 52350 Calc. Start / Grade Ability: 14.30% / 1.33% @ 55 MPH Calc. Geared Speed: 79.0 MPH FUEL ECONOMY: 6.34 MPG @ 55 MPH DIMENSION: Wheelbase: 177.00, CA: 115.00, Axle to Frame: 57.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 365 HP @ 1700 RPM, 1250 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 365 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FRO-14210C} 10-Speed Manual, With Overdrive, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 4.33 CAB: Conventional TIRE, FRONT: (2) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply TIRE, REAR: (8) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KT Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description CF7AA00 Base Chassis, Model CT660S SBA 6x4 with 177.00 Wheelbase, 115.00 CA, and 57.00 Axle to Frame. 1616 FRAME RAILS WITH TAPERED REAR 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 1LBC BUMPER, FRONT Multi-piece Stainless Steel Includes : FOG LIGHT OPENING (2) and with Rectangular Hole for Step 1WVR WHEELBASE RANGE 138" (350cm) Through and Including 181" (460cm) 2ASG AXLE, FRONT NON-DRIVING {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity 3ACH SUSPENSION, FRONT, SPRING Multileaf, Shackle Type; 14,000-lb Capacity; With Shock Absorbers Includes : SPRING PINS Threaded 4092 BRAKE SYSTEM, AIR Dual System for Tractor Applications Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : GLAD HANDS (2) One for Service and One for Emergency; Trailer Hoses from Cab : HAND CONTROL VALVE, AIR Mounted on Steering Column : HOSE TENDER Back of Cab Mounted : PARKING BRAKE CONTROL Yellow and Red Knobs, Located on Instrument Panel : PARKING BRAKE VALVE Combination Valve for Tractor and Trailer : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for Forward Rear Axle : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic : SWITCH, AUXILIARY Interrupter for Cab and Trailer Clearance/Marker Lights (Blinks Lights with Headlight Switch in "ON" Position); Instrument Panel Mounted : TRACTOR PROTECTION VALVE : TRAILER HOSES AND CABLES 15' Coiled Lighting Cable with 7-Way Connector and with 15' Coiled Nylon Brake Hose Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4193 BRAKES, FRONT, AIR CAM 16.5" x 6", Includes 24 SqIn Long Stroke Brake Chambers 4732 DRAIN VALVE {Berg} Manual; With Pull Chain, for Air Tank Includes : DRAIN VALVE Mounted in Wet Tank 4774 SPECIAL RATING, GAWR Provides Rear Tractor Brake Rating Equal to Axle Rating up to 23,000-lbs for Single Axles, 46,000-lbs for Tandem Axles, or 69,000-lb for Tridem Notes

Page 9: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

: The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4AAB BRAKE CHAMBERS, ADDITIONAL (2) {Haldex} Spring Brake Type; 30/30 SqIn Includes : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 Additional for Rear Rear Axle 4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel) Code Description 4EBS AIR DRYER {Bendix AD-9} With Heater Includes : AIR DRYER LOCATION Inside Left Rail, Back of Cab 4ETE BRAKE CHAMBERS, FRONT AXLE {Haldex} 24 SqIn 4EVL BRAKE CHAMBERS, REAR AXLE {Haldex GC3030LHDHO} 30/30 Spring Brake 4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.In. Long Stroke Brake Chamber and Spring Actuated Parking Brake 4SPM AIR COMPRESSOR {Bendix BA-921 Head Unload} 15.9 CFM Capacity, Single Cylinder 4WCC BRAKE PACKAGE, FRONT {Dana Spicer ES-165-6} Air, Cam Type, Extended Service; Size 16.5" x 6", Includes Automatic Slack Adjusters 4WCD BRAKE PACKAGE, REAR {Dana Spicer ES-165-7} Air, Cam Type, Extended Service; Size 16.5" x 7", Includes Automatic Slack Adjusters 5710 STEERING COLUMN Tilting and Telescoping 5PSA STEERING GEAR {Sheppard M-100} Power 5WBH STEERING WHEEL {Caterpillar} 2-Spoke, 18" Diam., Dark Neutral, Leather Wrapped 7BJU EXHAUST SYSTEM Switchback Horizontal Aftertreatment Device, Frame Mounted Right Side Under Cab; Includes Single Vertical Tail Pipe & Guard, Right Side, Cab Mounted 8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment Includes : BATTERY BOX Aluminum : CIGAR LIGHTER Includes Ash Cup, Center Console Mounted : FUSES, ELECTRICAL SAE Blade-Type : HAZARD SWITCH Integral with Turn Signal Switch : HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever : HEADLIGHTS (2) Composite with Halogen Projector Beam : HORN, AIR Single, Chrome : HORN, ELECTRIC Single : PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light : READING LIGHT, CAB (2) with Individual Switches; One Above Each Door : STARTER SWITCH Electric, Key Operated : STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector : TURN SIGNAL FLASHER : TURN SIGNAL SWITCH Manual Cancelling with Lane Change Feature : TURN SIGNALS, FRONT Includes Integral Reflectors and Side Marker Lights; Fender Mounted : WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature, Steering Column Mounted : WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted : WIRING, CHASSIS Color Coded and Continuously Numbered 8653 HORN, AIR Single, Located Under Cab 8718 POWER SOURCE Cigar Type Receptacle without Plug and Cord 8GGN ALTERNATOR {Bosch LH160} Brush Type, 12 Volt 160 Amp. Capacity, Pad Mount 8MMJ BATTERY SYSTEM {Caterpillar} (3) 12 Volt 2130CCA Total 8RMD RADIO AM/FM/WB/Clock/3MM Auxiliary Input, with Multiple Speakers 8RMG ANTENNA BASE (2) Single Function, (1) for CB and (1) for Entertainment Radio, Without Splitter, Separate Lead-Ins, With CB Antenna Mounted on Left Mirror and AM/FM Antenna Mounted on Right Mirror 8WCK POWER SOURCE, TERMINAL TYPE 2-Post Code Description 8WEZ TURN SIGNAL SWITCH Self-Canceling 8WKH BATTERY BOX Aluminum with Aluminum Cover, 18" Wide, 2, 3 or 4 Battery Capacity, Mounted Right Side Back of Cab 8WNH RUNNING LIGHT (2) Daytime 8WXG STARTING MOTOR {Mitsubishi Electric Automotive America 105P} 12-Volt, with Soft-Start 9ASE FRONT END Tilting Composite Includes : GRILLE SURROUND Brushed Stainless Steel 9HAN INSULATION, UNDER HOOD for Sound Abatement 9HBN INSULATION, SPLASH PANELS for Sound Abatement 10060 PAINT SCHEMATIC, PT-1 Single Color, Design 100 10761 PAINT TYPE Base Coat/Clear Coat, 1-2 Tone 10769 PAINT CLASS Premium Color 10EYC FIFTH WHEEL, STATIONARY {Fontaine SL7FMA-D69-3} Cast Top Plate; 8.69" Above Top of Frame; Left Hand Roadside Release 10WLX MUD FLAPS, REAR Black Rubber, Anti-Sail "CAT" Silver Logo; Less Holders

Page 10: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

10WPR MUD FLAP HOLDER Spring Loaded, Painted Black; With Red and White Reflective Tape; Less Flaps 11MGZ CLUTCH {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity Includes : CLUTCH RELEASE BEARING Greasable 12KXL ENGINE, DIESEL {CT 13} EPA 10, SCR, 365 HP @ 1700 RPM, 1250 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 365 Peak HP (Max) 12THT FAN DRIVE {Horton Drivemaster} Direct Drive Type, Two Speed With Residual Torque Device for Disengaged Fan Speed 12UBH RADIATOR Aluminum; Welded, Front to Back Down Flow System, 1564 SqIn, 1572 SqIn Dual CAC, 1293 SqIn 3 Core LTR 12VBT AIR CLEANER Single Element, Heavy Duty 12VED FEDERAL EMISSIONS for 2010; CT 13 Engines 12WCX HOSE CLAMPS, RADIATOR HOSES {Gates} Shrink Band Type 12WEG COLD STARTING EQUIPMENT Automatic; With Engine ECM Control 12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, Engine Mounted 12WZJ EMISSION COMPLIANCE Low NOx Idle Engine, Complies with California Clean Air Regulations; Includes "Certified Clean Idle" Decal located on Driver Door 12XAN OBD COMPLIANCE for 2013 OBD (On Board Diagnostics) 13GHL TRANSMISSION, MANUAL {Fuller FRO-14210C} 10-Speed Manual, With Overdrive, With Air Shift Includes : CLUTCH BRAKE Torque Limiting : FILL PLUG, MAGNETIC Code Description 13WAP TRANSMISSION LUBE PUMP for International, Fuller, Meritor or Spicer Transmissions; USE ONLY WHEN PUMP IS NOT INCLUDED STANDARD IN TRANSMISSION 13WGJ OIL COOLER,MANUAL TRANSMISSION Water to Oil Type Included in Radiator End Tank (REQUIRES TRANSMISSION LUBE PUMP) 13WLB TRANSMISSION OIL {EmGard 50W} Synthetic; 22 thru 33.99 Pints 14GVU AXLE, REAR, TANDEM {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Lube Oil Pump . Gear Ratio: 4.33 Includes : POWER DIVIDER LOCK Air Operated, Cab Control with Indicator Light in Cluster : REAR AXLE DRAIN PLUG (2) Magnetic, For Tandem Rear Axle 14ULX SUSPENSION, REAR, TANDEM {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000- lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers Includes : CROSSMEMBER, SUSPENSION Stamped Steel Double Dogbone Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 14WAL SUSPENSION/REAR-AXLE IDENTITY for Meritor Tandem Rear Axles With Bar-Pin Beam Attachment Type Suspensions 14WBV SHOCK ABSORBERS, REAR (4) for Hendrickson HMX Suspension Only, Mounted from Frame to Beam 14WLD AXLE, REAR, LUBE {EmGard 75W-90} Synthetic Oil; 50 thru 64.99 Pints 15DYP DEF TANK 9.5 U.S. Gal. 36.0L Capacity, Frame Mounted Outside Left Rail, Under Cab 15LKU FUEL/WATER SEPARATOR {Racor} Fuel Pre-Filter and Filter Base, Includes Water-In-Fuel Sensor 15SJZ FUEL TANK Top Draw; Non-Polished Aluminum, 26" Diam., 80 U.S. Gal., 302 L Capacity Mounted Left Side, Under Cab 16031 CAB Conventional Includes : COAT HOOK, CAB Located on Rear Wall, Behind Passenger Seat : CONSOLE, CENTER Plastic, Driver Convenience with a Cup and Change Holder, Ash Tray and Lower Storage Area : DOME LIGHT, CAB (2) Driver and Passenger Dome Lights with Individual Switches, in Headliner : DOOR CHECK STRAP (2) One Each Door : GLASS, ALL WINDOWS Tinted : GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side : GRAB HANDLE, EXTERIOR (2) Mounted Behind Driver and Passenger Doors : INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color : SKIN Riveted : STEP (4) Two Steps Per Door 16400 SEAT, PASSENGER Omit Item 16HBA GAUGE CLUSTER English With English Electronic Speedometer 16JPC SEAT, DRIVER {National 2000 Model 295} Air Suspension, Intermediate Back, All Vinyl, 2 Arm Rests, Isolator, 7" Adjuster, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, 3 Position Rear Cushion, 2-15 Degree Back Angle Adjust, Vinyl Suspension Cover 16SKS MIRRORS (2) {Lang Mekra} Aero; Rectangular, 7.09" x 15.75" & Integral Convex Both Sides, 102" Inside Spacing, Breakaway Type, Heated Heads Thermostat Controlled, Amber Lens Clearance Light LED, Black

Page 11: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Painted Finish Heads, Brackets & Arms Code Description 16VRT HEATER, ENHANCED CIRCULATION {Bergstrom} Control, for Extreme Cold Weather Climates 16VTH CAB INTERIOR TRIM Premium Level; for Caterpillar, Day Cab Includes : "A" PILLAR COVER Molded Plastic : CAB INTERIOR TRIM PANELS Vinyl : CONSOLE, OVERHEAD Molded Plastic with Three Storage Pockets; One with Strap for CB Radio Mounting; Two with Netting, Courtesy Lights with Switches : COURTESY LIGHT (2) Driver and Passenger Door Mounted : DOOR TRIM PANELS Vinyl Upper with Power Locks and Windows, Upper and Lower Grab Handles, Both Sides : FLOOR COVERING Rubber, Black : HEADLINER Soft Padded Vinyl : HEATER BOX Metal, Painted Black : INSTRUMENT PANEL TRIM Vinyl : MIRROR, CONVEX, LOOK DOWN Black Finish; 6" x 10-1/4"; Located on Passenger Side : STORAGE POCKET, DOOR (2) Driver and Passenger Door : SUN VISOR (2) Vinyl with Molded Toll Ticket Retainer 16VZA WINDOW, REAR 52.25" Wide 16WAK WINDOW, POWER (2) in Left and Right Doors 16WJG CAB DOOR LOCKS Power 16WKB AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster 16WKR WINDSHIELD Single Piece 16WLD CAB REAR SUSPENSION {Link Z9079D1} Dual Frame Mounted Cab Rear Air Suspension; Includes Special Crossmember Assembly 16XWD SUNSHADE, EXTERIOR Aerodynamic, Painted Roof Color; Includes Integral Clearance/Marker Lights 27DMD WHEELS, FRONT DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Aluminum Hubs 28DMD WHEELS, REAR DUAL DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Aluminum Hubs. 7372135415 (2) TIRE, FRONT 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply 7372135415 (8) TIRE, REAR 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply 810000 FIFTH WHEEL LOCATION On Rear Axle Centerline Graphics are provided as visual aids only and are not intended to represent the actual scale, shape, or color of the truck or its components. All weights are represented in lbs. Truck Body/Trailer Chassis/Empty Weights Bumper to Axle (BA) 54.0 Wheelbase (WB)177.00 Axle to Frame (AF) 57.00 Axle to Back Cab (ABC) 62 Cab to Axle (CA) 115 Usable CA 115 CA Reduction Adjustment 0 Fuel-Diesel(Gals) 50 DEF(Gals) 0 Trailer Length (TL) 540 5th Wheel Position (FW) 0 5th Wheel to Axle (FWA) 444 Trailer Wheelbase 444 Nose of Trailer to KP (KP) 36 Axle to Back of Trailer (AB) 60 Tractor Front Axle: 9,684 Tractor Rear Axle: 7,082 Trailer King Pin: 1,500 Trailer Rear Axle: 3,500 Payloads Before the Cab Cab Chassis Body After the Body # Weight CG # Weight CG # Weight CG # Weight CG # Weight CG 1 26,000 79 2 29,000 458 Loads Weight Distribution Payload Weight: 55,000 Driver: 250 Fuel-Diesel(Lbs): 355 DEF(Lbs): 0 Total Front Axle: 10,050 Total Rear Axle: 33,740

Page 12: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Total Rear Trailer: 33,581 Total Weight: 77,371 Weights and clearances in this proposal are estimates only. Neither Caterpillar nor its suppliers are liable for any consequences resulting from any differences between the estimated weights and clearances and the actual manufactured weights and clearances. Weight Distribution All weights are represented in lbs. 0"off centerline Tractor Trailer Front Rear Rear Total Chassis Weight Chassis Weight: 9,684 7,082 0 16,766 Fuel: 178 177 0 355 DEF: 0 0 0 0 Empty Trailer: 0 1,500 3,500 5,000 (Curb Weight): 9,862 8,759 3,500 22,121 Loads Payloads: 0 24,919 30,081 55,000 Driver: 188 62 0 250 Axle Totals (Gross Weight): 10,050 33,740 33,581 77,371 Weight Ratings Tractor Trailer Front Rear Rear Axle(axle capacity) 13,200 40,000 Tire(tire capacity) 12,350 46,720 Suspension(suspension capacity) 14,000 40,000 Spring: 0 Fed Bridge Law (axle spread): 20,000 34,000 (54") 34,000 (48") Wheel Combination Load Limit 1 - 3 43,790 48,500 2 - 5 67,321 69,500 1 - 5 77,371 81,000 Federal Total Vehicle Weight Limit: 80,000 Maximum Gross Vehicle Weight Rating (GVWR) 52,350 - Gross Vehicle Weight(GVW) 43,790 = 8,560 Reserves Weight Summary * Distributed weights are within capacity limits ENGINE, DIESEL (0012KXL) ATTACHMENTS: 0016HBA (GAUGE CLUSTER) 0015LKU (FUEL/WATER SEPARATOR) 0012WEG (COLD STARTING EQUIPMENT) 0012THT (FAN DRIVE) Parameter Value UOM Max Accelerator Vehicle Speed:7902 79 MPH Vehicle Speed Limiter Override:7911 0, DISABLE FEATURE OR FUNCTION N/A VSLO Speed Increment:7912 10 MPH VSLO Maximum Activation Time:7914 30 MIN VSLO Time Interval to Reset:7915 8.0 HOURS VSLO Time Duration Source:7934 1, INTERVAL BASED ON REAL TIME CLOCK N/A Progressive Shift Enable:7744 0, DISABLE FEATURE OR FUNCTION N/A Low Gear Ratio Break Point:7742 5.825000 N/A High Gear Ratio Break Point:7743 1.643500000 N/A Low Gear Engine Speed Limit:7738 1550.0 RPM High Gear Engine Speed Limit:7739 1600.0 RPM Low Gear Engine Speed Range:7740 200.0 RPM High Gear Engine Speed Range:7741 200.0 RPM Min Gear Ratio for ProShift:7755 0.50 N/A Gear Down Protection Enable:7714 0, DISABLE FEATURE OR FUNCTION N/A Top Gr Minus 2 Light Ld VS Lim:7715 31 MPH Top Gr Minus 1 Light Ld VS Lim:7716 41 MPH Top Gr Minus 2 Heavy Ld VS Lim:7735 33 MPH Top Gr Minus 1 Heavy Ld VS Lim:7736 46 MPH Driver Reward Enable:7918 0, DISABLE FEATURE OR FUNCTION N/A Driver Reward Mode:7930 2, BOTH ACCELERATOR AND CRUISE VEHICLE SPEED LIMIT INCREASE N/A Driver Reward Performance Crit:7925 0, FUEL ECONOMY BASED REWARD SYSEM N/A Fuel Economy - Expected Level:7921 6.00 MPG Fuel Economy - Good Level:7920 6.25 MPG

Page 13: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Fuel Economy - Excellent Level:7919 6.40 MPG % Idle Time - Expected Level:7924 25 % % Idle Time - Good Level:7923 18 % % Idle Time - Excellent Level:7922 10 % Driver Reward Ambient Temp H:7938 150.0 C Driver Reward Ambient Temp L:7939 -40.0 C VS Lim Increase - Expected Lvl:7926 0 MPH VS Lim Increase - Good Lvl:7927 2 MPH VS Lim Increase - Excel Lvl:7928 4 MPH VS Lim Decrease - Penalty Lvl:7929 -2 MPH Idle Engine Speed:8202 600.0 RPM Idle Speed Adjustment Enable:8215 1, ENABLE FEATURE OR FUNCTION N/A Idle Spd Adjust - Max Eng Spd:8212 0.0 RPM Idle Spd Adjust - Bump Step:8216 5.0 RPM Idle Spd Adjust Ramp Rate:8211 25 RPM/SEC Maximum Standstill Eng Speed:7753 2100.0 RPM Idle Shutdown Mode:7400 0, DISABLE FEATURE OR FUNCTION N/A ISD Time w/Park Brk Released:7401 15.0 MIN ISD Time w/Park Brake Set:7404 5.0 MIN ISD Latched Driver Override En:7407 0, DISABLE FEATURE OR FUNCTION N/A ISD Ambient Temp Override En:7408 0, DISABLE FEATURE OR FUNCTION N/A ISD Int Amb Temp Enable:7405 0, DISABLE FEATURE OR FUNCTION N/A ISD Max Ambient Temp Override:7402 20.0 C ISD Int Amb Temp Override:7406 15.0 C ISD Min Ambient Temp Override:7403 5.0 C ISD Max Engine Coolant Temp:7412 150.0 C ISD Min Engine Coolant Temp:7413 16.0 C ISD Idle Shutdown Max Eng Trq:7409 80 % Cruise Control Enable:7600 1, ENABLE FEATURE OR FUNCTION N/A Electronic Parameters CC Max Vehicle Speed:7604 79 MPH CC Min Vehicle Speed:7603 25.0000 MPH AESC Control:7500 0, DISABLE FEATURE OR FUNCTION N/A AESC In-cab Mode:7502 2, VARIABLE ENGINE SPEED CONTROL SELECTED N/A AESC Min Engine Speed:7522 600.0 RPM AESC Max Engine Speed:7508 1500.0 RPM AESC Preset Engine Speed 1:7505 800.0 RPM AESC Preset Engine Speed 2:7506 900.0 RPM AESC Preset Engine Speed 3:7514 1000.0 RPM AESC Preset Engine Speed 4:7515 1100.0 RPM AESC Preset Engine Speed 5:7516 1200.0 RPM AESC Preset Engine Speed 6:7517 1300.0 RPM AESC Activate at Preset Speed:7528 0, NO PRESET PRESELECTION N/A AESC Ramp Up Rate:7507 100.00 RPM/SEC AESC Ramp Down Rate:7524 100.00 RPM/SEC AESC Bump Up/Down Step:7525 25.0 RPM AESC In-cab Operator Interface:7503 0, NO (OFF) OR DISABLE N/A AESC Disable w/ Clutch Pedal:7510 1, ENABLE FEATURE OR FUNCTION N/A AESC Disable w/ Brake Pedal:7511 1, ENABLE FEATURE OR FUNCTION N/A AESC Accel Pedal Mode:7513 1, AESC OVERRIDDEN BY ACCELERATOR PEDAL N/A AESC Max Engine Load:7519 100.0000 % AESC Control to Engine Load:7530 0, KICK OUT OF AESC ABOVE PROGRAMMED LIMIT N/A AESC Max Engine Load Time:7527 8 SEC AESC Vehicle Speed Limit:7521 5.0000 MPH AESC Max Mobile Veh Spd:7501 5 MPH AESC Eng Spd Limit w/VSS Fault:7518 1500 RPM AESC Force Fan On:9007 0, DISABLE FEATURE OR FUNCTION N/A AESC Park Brake Override:7534 1, ENABLE FEATURE OR FUNCTION N/A AESC Transfer Case Signal Mode:8910 0, DRIVELINE N/A AESC Splitshaft Veh SPD Dsply:9307 0, SPEED SENSOR LOCATED IN WHEEL RIM N/A AESC Remote Accel Pedal Enable:7504 0, DISABLE FEATURE OR FUNCTION N/A AESC Remote Accel Pedal Switch:8914 0, DISABLE FEATURE OR FUNCTION N/A AESC Accel Max Eng Spd Ovrd:7520 1900.0 RPM Rem Accelerator Switch Input:9929 1, SAE J1939 MULTIPLEXED N/A Preset Remote AESC Input Type:9932 0, DISCRETE (HARDWIRED) INPUT N/A Variable Remote AESC Input:9933 0, DISCRETE (HARDWIRED) INPUT N/A Rem Accelerator Position Input:9935 1, SAE J1939 MULTIPLEXED N/A Engine Protection Mode:7700 1, TWO WAY WARNING (OIL PRES, WATER TEMP) N/A Powertrain Protection Enable:7722 0, DISABLE FEATURE OR FUNCTION N/A

Page 14: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Torque Limiting in Gear:7717 0, DISABLE FEATURE OR FUNCTION N/A Highest Gear of Low Range:7718 2 N/A Highest Gear Rat of Low Range:7745 6.00 N/A Highest Gear of Int. Range:7748 4 N/A Highest Gear Rat of Int. Range:7746 4.00 N/A Highest Gear of High Range:7749 6 N/A Highest Gear Rat of High Range:7747 2.00 N/A Max Torque in Low Gear Range:7713 1250.0000 LB-FT Max Torque in Int. Gear Range:7750 1250.0000 LB-FT Max Torque in High Gear Range:7751 1250.0000 LB-FT VSS Anti-Tamper Max Eng Speed:7901 1410.0 RPM Auxilllary Shutdown Input Type:9931 0, DISCRETE (HARDWIRED) INPUT N/A Veh Speed Sensor Antitampering:7905 0, DISABLE FEATURE OR FUNCTION N/A Veh Overspd Threshold Level 1:7723 84.462626 MPH Veh Overspd Threshold Level 2:7724 86.462626 MPH Service Interval Enable 0, DISABLE FEATURE OR FUNCTION N/A Fuel Used Service Interval:9501 0 GALLONS Engine Hour Service Interval:9502 0 HOURS Veh Distance Service Interval:9503 0 MILES Service Soon Percent to Notify:9507 90 % Customer Unit Number:6605 0 N/A Hard Braking Incident Counter:8904 1, ENABLE FEATURE OR FUNCTION N/A Hard Braking Decel Threshold:8905 7.40 MPH/SEC Vehicle Over-speed Indicator:7754 0, FEATURE OR FUNCTION IS DISABLED N/A Customer Password:8700 00000000 N/A These Electronic Parameters have not been finalized

Page 15: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

H-GAC Product Code: B3 CT660-LTA, TRA, 122” BBC (CF7AB), Truck Configuration

Model Profile 2015 CT660L SBA 6x4 (CF7AB) APPLICATION: Utility/Service (Other) MISSION: Requested GVWR: 52300. Calc. GVWR: 52350 Calc. Start / Grade Ability: 34.60% / 3.26% @ 55 MPH Calc. Geared Speed: 74.0 MPH FUEL ECONOMY: 7.49 MPG @ 55 MPH DIMENSION: Wheelbase: 181.00, CA: 113.00, Axle to Frame: 53.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FR-14210B} 10-Speed Manual, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 3.42 CAB: Conventional TIRE, FRONT: (2) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply TIRE, REAR: (8) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KU Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description CF7AB00 Base Chassis, Model CT660L SBA 6x4 with 181.00 Wheelbase, 113.00 CA, and 53.00 Axle to Frame. 1652 CROSSMEMBER, REAR Relocated to End of Frame 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 1LBC BUMPER, FRONT Multi-piece Stainless Steel Includes : FOG LIGHT OPENING (2) and with Rectangular Hole for Step 1WVX WHEELBASE RANGE 181" (460cm) Through and Including 234" (595cm) 2ASG AXLE, FRONT NON-DRIVING {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity 3ACH SUSPENSION, FRONT, SPRING Multileaf, Shackle Type; 14,000-lb Capacity; With Shock Absorbers Includes : SPRING PINS Threaded 4091 BRAKE SYSTEM, AIR Dual System for Straight Truck Applications Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : DUST SHIELDS, FRONT BRAKE : DUST SHIELDS, REAR BRAKE : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : INVERSION VALVE Bendix SR-1 and Double Check Valve : PARKING BRAKE CONTROL Yellow Knob, Located on Instrument Panel : PARKING BRAKE VALVE For Truck : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for 4x2, 2 for 6x4 : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic : SWITCH, AUXILIARY Interrupter for Cab Clearance/Marker Lights (Blinks Lights with Headlight Switch in "ON" Position); Instrument Panel Mounted Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4193 BRAKES, FRONT, AIR CAM 16.5" x 6", Includes 24 SqIn Long Stroke Brake Chambers 4619 TRAILER CONNECTIONS Four-Wheel, With Hand Control Valve and Tractor Protection Valve, for Straight Truck Includes : INVERSION VALVE Bendix SR-1 and Double Check Valve 4732 DRAIN VALVE {Berg} Manual; With Pull Chain, for Air Tank Includes : DRAIN VALVE Mounted in Wet Tank 4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel) 4EBS AIR DRYER {Bendix AD-9} With Heater

Page 16: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Includes : AIR DRYER LOCATION Inside Left Rail, Back of Cab 4ETE BRAKE CHAMBERS, FRONT AXLE {Haldex} 24 SqIn 4EVL BRAKE CHAMBERS, REAR AXLE {Haldex GC3030LHDHO} 30/30 Spring Brake Code Description 4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.In. Long Stroke Brake Chamber and Spring Actuated Parking Brake 4SPM AIR COMPRESSOR {Bendix BA-921 Head Unload} 15.9 CFM Capacity, Single Cylinder 4WCC BRAKE PACKAGE, FRONT {Dana Spicer ES-165-6} Air, Cam Type, Extended Service; Size 16.5" x 6", Includes Automatic Slack Adjusters 4WCD BRAKE PACKAGE, REAR {Dana Spicer ES-165-7} Air, Cam Type, Extended Service; Size 16.5" x 7", Includes Automatic Slack Adjusters 5710 STEERING COLUMN Tilting and Telescoping 5PSA STEERING GEAR {Sheppard M-100} Power 5WBH STEERING WHEEL {Caterpillar} 2-Spoke, 18" Diam., Dark Neutral, Leather Wrapped 7BJU EXHAUST SYSTEM Switchback Horizontal Aftertreatment Device, Frame Mounted Right Side Under Cab; Includes Single Vertical Tail Pipe & Guard, Right Side, Cab Mounted 8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment Includes : BATTERY BOX Aluminum : CIGAR LIGHTER Includes Ash Cup, Center Console Mounted : FUSES, ELECTRICAL SAE Blade-Type : HAZARD SWITCH Integral with Turn Signal Switch : HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever : HEADLIGHTS (2) Composite with Halogen Projector Beam : HORN, AIR Single, Chrome : HORN, ELECTRIC Single : PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light : READING LIGHT, CAB (2) with Individual Switches; One Above Each Door : STARTER SWITCH Electric, Key Operated : STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector : TURN SIGNAL FLASHER : TURN SIGNAL SWITCH Manual Cancelling with Lane Change Feature : TURN SIGNALS, FRONT Includes Integral Reflectors and Side Marker Lights; Fender Mounted : WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature, Steering Column Mounted : WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted : WIRING, CHASSIS Color Coded and Continuously Numbered 8554 TRAILER CONNECTION SOCKET 7-Way; Mounted at Rear of Frame 8653 HORN, AIR Single, Located Under Cab 8718 POWER SOURCE Cigar Type Receptacle without Plug and Cord 8GGN ALTERNATOR {Bosch LH160} Brush Type, 12 Volt 160 Amp. Capacity, Pad Mount 8MMJ BATTERY SYSTEM {Caterpillar} (3) 12 Volt 2130CCA Total 8RMD RADIO AM/FM/WB/Clock/3MM Auxiliary Input, with Multiple Speakers 8RMG ANTENNA BASE (2) Single Function, (1) for CB and (1) for Entertainment Radio, Without Splitter, Separate Lead-Ins, With CB Antenna Mounted on Left Mirror and AM/FM Antenna Mounted on Right Mirror 8WCK POWER SOURCE, TERMINAL TYPE 2-Post 8WEZ TURN SIGNAL SWITCH Self-Canceling 8WKH BATTERY BOX Aluminum with Aluminum Cover, 18" Wide, 2, 3 or 4 Battery Capacity, Mounted Right Side Back of Cab 8WNH RUNNING LIGHT (2) Daytime Code Description 8WXG STARTING MOTOR {Mitsubishi Electric Automotive America 105P} 12-Volt, with Soft-Start 9ASE FRONT END Tilting Composite Includes : GRILLE SURROUND Brushed Stainless Steel 9HAN INSULATION, UNDER HOOD for Sound Abatement 9HBN INSULATION, SPLASH PANELS for Sound Abatement 10060 PAINT SCHEMATIC, PT-1 Single Color, Design 100 10761 PAINT TYPE Base Coat/Clear Coat, 1-2 Tone 10769 PAINT CLASS Premium Color 11MGZ CLUTCH {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity Includes : CLUTCH RELEASE BEARING Greasable 12KXP ENGINE, DIESEL {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) 12THT FAN DRIVE {Horton Drivemaster} Direct Drive Type, Two Speed With Residual Torque Device for Disengaged Fan Speed 12UBH RADIATOR Aluminum; Welded, Front to Back Down Flow System, 1564 SqIn, 1572 SqIn Dual CAC, 1293

Page 17: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

SqIn 3 Core LTR 12VBT AIR CLEANER Single Element, Heavy Duty 12VED FEDERAL EMISSIONS for 2010; CT 13 Engines 12WCX HOSE CLAMPS, RADIATOR HOSES {Gates} Shrink Band Type 12WEG COLD STARTING EQUIPMENT Automatic; With Engine ECM Control 12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, Engine Mounted 12WZJ EMISSION COMPLIANCE Low NOx Idle Engine, Complies with California Clean Air Regulations; Includes "Certified Clean Idle" Decal located on Driver Door 12XAN OBD COMPLIANCE for 2013 OBD (On Board Diagnostics) 13GHJ TRANSMISSION, MANUAL {Fuller FR-14210B} 10-Speed Manual, With Air Shift Includes : CLUTCH BRAKE Torque Limiting : FILL PLUG, MAGNETIC 13WAP TRANSMISSION LUBE PUMP for International, Fuller, Meritor or Spicer Transmissions; USE ONLY WHEN PUMP IS NOT INCLUDED STANDARD IN TRANSMISSION 13WGJ OIL COOLER,MANUAL TRANSMISSION Water to Oil Type Included in Radiator End Tank (REQUIRES TRANSMISSION LUBE PUMP) 13WLB TRANSMISSION OIL {EmGard 50W} Synthetic; 22 thru 33.99 Pints 14GVU AXLE, REAR, TANDEM {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Lube Oil Pump . Gear Ratio: 3.42 Includes : POWER DIVIDER LOCK Air Operated, Cab Control with Indicator Light in Cluster : REAR AXLE DRAIN PLUG (2) Magnetic, For Tandem Rear Axle Code Description 14ULX SUSPENSION, REAR, TANDEM {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000- lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers Includes : CROSSMEMBER, SUSPENSION Stamped Steel Double Dogbone Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 14WAL SUSPENSION/REAR-AXLE IDENTITY for Meritor Tandem Rear Axles With Bar-Pin Beam Attachment Type Suspensions 14WBV SHOCK ABSORBERS, REAR (4) for Hendrickson HMX Suspension Only, Mounted from Frame to Beam 14WLD AXLE, REAR, LUBE {EmGard 75W-90} Synthetic Oil; 50 thru 64.99 Pints 15DYP DEF TANK 9.5 U.S. Gal. 36.0L Capacity, Frame Mounted Outside Left Rail, Under Cab 15LKU FUEL/WATER SEPARATOR {Racor} Fuel Pre-Filter and Filter Base, Includes Water-In-Fuel Sensor 15SGL FUEL TANK Non-Polished Aluminum, 24" Diam., 80 U.S. Gal., 302 L Capacity Mounted Left Side Under Cab 16031 CAB Conventional Includes : COAT HOOK, CAB Located on Rear Wall, Behind Passenger Seat : CONSOLE, CENTER Plastic, Driver Convenience with a Cup and Change Holder, Ash Tray and Lower Storage Area : DOME LIGHT, CAB (2) Driver and Passenger Dome Lights with Individual Switches, in Headliner : DOOR CHECK STRAP (2) One Each Door : GLASS, ALL WINDOWS Tinted : GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side : GRAB HANDLE, EXTERIOR (2) Mounted Behind Driver and Passenger Doors : INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color : SKIN Riveted : STEP (4) Two Steps Per Door 16400 SEAT, PASSENGER Omit Item 16HBA GAUGE CLUSTER English With English Electronic Speedometer 16JPC SEAT, DRIVER {National 2000 Model 295} Air Suspension, Intermediate Back, All Vinyl, 2 Arm Rests, Isolator, 7" Adjuster, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, 3 Position Rear Cushion, 2-15 Degree Back Angle Adjust, Vinyl Suspension Cover 16SKS MIRRORS (2) {Lang Mekra} Aero; Rectangular, 7.09" x 15.75" & Integral Convex Both Sides, 102" Inside Spacing, Breakaway Type, Heated Heads Thermostat Controlled, Amber Lens Clearance Light LED, Black Painted Finish Heads, Brackets & Arms 16VRT HEATER, ENHANCED CIRCULATION {Bergstrom} Control, for Extreme Cold Weather Climates 16VTH CAB INTERIOR TRIM Premium Level; for Caterpillar, Day Cab Includes : "A" PILLAR COVER Molded Plastic : CAB INTERIOR TRIM PANELS Vinyl : CONSOLE, OVERHEAD Molded Plastic with Three Storage Pockets; One with Strap for CB Radio Mounting; Two with Netting, Courtesy Lights with Switches : COURTESY LIGHT (2) Driver and Passenger Door Mounted : DOOR TRIM PANELS Vinyl Upper with Power Locks and Windows, Upper and Lower Grab Handles, Both Sides

Page 18: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

: FLOOR COVERING Rubber, Black : HEADLINER Soft Padded Vinyl Code Description : HEATER BOX Metal, Painted Black : INSTRUMENT PANEL TRIM Vinyl : MIRROR, CONVEX, LOOK DOWN Black Finish; 6" x 10-1/4"; Located on Passenger Side : STORAGE POCKET, DOOR (2) Driver and Passenger Door : SUN VISOR (2) Vinyl with Molded Toll Ticket Retainer 16VZA WINDOW, REAR 52.25" Wide 16WAK WINDOW, POWER (2) in Left and Right Doors 16WJG CAB DOOR LOCKS Power 16WKB AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster 16WKR WINDSHIELD Single Piece 16WLD CAB REAR SUSPENSION {Link Z9079D1} Dual Frame Mounted Cab Rear Air Suspension; Includes Special Crossmember Assembly 16XWD SUNSHADE, EXTERIOR Aerodynamic, Painted Roof Color; Includes Integral Clearance/Marker Lights 27DMA WHEELS, FRONT DISC; 22.5" Painted Steel, 2 Hand Hole, 10 Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs Includes : PAINT IDENTITY, FRONT WHEELS White 28DMA WHEELS, REAR DUAL DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs Includes : PAINT IDENTITY, REAR WHEELS White 7372135415 (2) TIRE, FRONT 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply 7372135415 (8) TIRE, REAR 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply Graphics are provided as visual aids only and are not intended to represent the actual scale, shape, or color of the truck or its components. All weights are represented in lbs. Truck Body/Trailer Chassis/Empty Weights Bumper to Axle (BA) 54.0 Wheelbase (WB)181.00 Axle to Frame (AF) 53.00 Axle to Back Cab (ABC) 68 Cab to Axle (CA) 113 Usable CA 113 CA Reduction Adjustment 0 Fuel-Diesel(Gals) 50 DEF(Gals) 0 Body Length (BL) 256 Tractor Front Axle: 9,531 Tractor Rear Axle: 7,191 Payloads Before the Cab Cab Chassis Body After the Body # Weight CG # Weight CG # Weight CG # Weight CG # Weight CG 1 23,500 80 Loads Weight Distribution Payload Weight: 23,500 Driver: 250 Fuel-Diesel(Lbs): 355 DEF(Lbs): 0 Total Front Axle: 13,282 Total Rear Axle: 32,545 Total Weight: 45,827 Weights and clearances in this proposal are estimates only. Neither Caterpillar nor its suppliers are liable for any consequences resulting from any differences between the estimated weights and clearances and the actual manufactured weights and clearances. Weight Distribution All weights are represented in lbs. Truck Front Rear Total Chassis Weight Chassis Weight: 9,531 7,191 16,722 Fuel: 165 190 355 DEF: 0 0 0 Empty Body: -497 5,497 5,000 (Curb Weight): 9,199 12,878 22,077 Loads Payloads: 3,895 19,605 23,500 Driver: 188 62 250

Page 19: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Axle Totals (Gross Weight): 13,282 32,545 45,827 Weight Ratings Truck Front Rear Axle(axle capacity) 13,200 40,000 Tire(tire capacity) 12,350 46,720 Suspension(suspension capacity) 14,000 40,000 Spring: 0 Fed Bridge Law (axle spread): 20,000 34,000 (54") Wheel Combination Load Limit 1 - 3 45,827 48,500 Federal Total Vehicle Weight Limit: 80,000 Maximum Gross Vehicle Weight Rating (GVWR) 52,350 - Gross Vehicle Weight(GVW) 45,827 = 6,523 Reserves Weight Summary * Front Tractor - Axle Weight exceeds Axle capacity ENGINE, DIESEL (0012KXP) ATTACHMENTS: 0016HBA (GAUGE CLUSTER) 0015LKU (FUEL/WATER SEPARATOR) 0012WEG (COLD STARTING EQUIPMENT) 0012THT (FAN DRIVE) Parameter Value UOM Max Accelerator Vehicle Speed:7902 74 MPH Vehicle Speed Limiter Override:7911 0, DISABLE FEATURE OR FUNCTION N/A VSLO Speed Increment:7912 10 MPH VSLO Maximum Activation Time:7914 30 MIN VSLO Time Interval to Reset:7915 8.0 HOURS VSLO Time Duration Source:7934 1, INTERVAL BASED ON REAL TIME CLOCK N/A Progressive Shift Enable:7744 0, DISABLE FEATURE OR FUNCTION N/A Low Gear Ratio Break Point:7742 7.029500 N/A High Gear Ratio Break Point:7743 2.133000000 N/A Low Gear Engine Speed Limit:7738 1550.0 RPM High Gear Engine Speed Limit:7739 1600.0 RPM Low Gear Engine Speed Range:7740 200.0 RPM High Gear Engine Speed Range:7741 200.0 RPM Min Gear Ratio for ProShift:7755 0.50 N/A Gear Down Protection Enable:7714 0, DISABLE FEATURE OR FUNCTION N/A Top Gr Minus 2 Light Ld VS Lim:7715 29 MPH Top Gr Minus 1 Light Ld VS Lim:7716 39 MPH Top Gr Minus 2 Heavy Ld VS Lim:7735 32 MPH Top Gr Minus 1 Heavy Ld VS Lim:7736 42 MPH Driver Reward Enable:7918 0, DISABLE FEATURE OR FUNCTION N/A Driver Reward Mode:7930 2, BOTH ACCELERATOR AND CRUISE VEHICLE SPEED LIMIT INCREASE N/A Driver Reward Performance Crit:7925 0, FUEL ECONOMY BASED REWARD SYSEM N/A Fuel Economy - Expected Level:7921 6.00 MPG Fuel Economy - Good Level:7920 6.25 MPG Fuel Economy - Excellent Level:7919 6.40 MPG % Idle Time - Expected Level:7924 25 % % Idle Time - Good Level:7923 18 % % Idle Time - Excellent Level:7922 10 % Driver Reward Ambient Temp H:7938 150.0 C Driver Reward Ambient Temp L:7939 -40.0 C VS Lim Increase - Expected Lvl:7926 0 MPH VS Lim Increase - Good Lvl:7927 2 MPH VS Lim Increase - Excel Lvl:7928 4 MPH VS Lim Decrease - Penalty Lvl:7929 -2 MPH Idle Engine Speed:8202 600.0 RPM Idle Speed Adjustment Enable:8215 1, ENABLE FEATURE OR FUNCTION N/A Idle Spd Adjust - Max Eng Spd:8212 0.0 RPM Idle Spd Adjust - Bump Step:8216 5.0 RPM Idle Spd Adjust Ramp Rate:8211 25 RPM/SEC Maximum Standstill Eng Speed:7753 2100.0 RPM Idle Shutdown Mode:7400 0, DISABLE FEATURE OR FUNCTION N/A ISD Time w/Park Brk Released:7401 15.0 MIN ISD Time w/Park Brake Set:7404 5.0 MIN ISD Latched Driver Override En:7407 0, DISABLE FEATURE OR FUNCTION N/A ISD Ambient Temp Override En:7408 0, DISABLE FEATURE OR FUNCTION N/A ISD Int Amb Temp Enable:7405 0, DISABLE FEATURE OR FUNCTION N/A ISD Max Ambient Temp Override:7402 20.0 C

Page 20: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

ISD Int Amb Temp Override:7406 15.0 C ISD Min Ambient Temp Override:7403 5.0 C ISD Max Engine Coolant Temp:7412 150.0 C ISD Min Engine Coolant Temp:7413 16.0 C ISD Idle Shutdown Max Eng Trq:7409 80 % Cruise Control Enable:7600 1, ENABLE FEATURE OR FUNCTION N/A Electronic Parameters Summary CC Max Vehicle Speed:7604 74 MPH CC Min Vehicle Speed:7603 25.0000 MPH AESC Control:7500 0, DISABLE FEATURE OR FUNCTION N/A AESC In-cab Mode:7502 2, VARIABLE ENGINE SPEED CONTROL SELECTED N/A AESC Min Engine Speed:7522 600.0 RPM AESC Max Engine Speed:7508 1500.0 RPM AESC Preset Engine Speed 1:7505 800.0 RPM AESC Preset Engine Speed 2:7506 900.0 RPM AESC Preset Engine Speed 3:7514 1000.0 RPM AESC Preset Engine Speed 4:7515 1100.0 RPM AESC Preset Engine Speed 5:7516 1200.0 RPM AESC Preset Engine Speed 6:7517 1300.0 RPM AESC Activate at Preset Speed:7528 0, NO PRESET PRESELECTION N/A AESC Ramp Up Rate:7507 100.00 RPM/SEC AESC Ramp Down Rate:7524 100.00 RPM/SEC AESC Bump Up/Down Step:7525 25.0 RPM AESC In-cab Operator Interface:7503 0, NO (OFF) OR DISABLE N/A AESC Disable w/ Clutch Pedal:7510 1, ENABLE FEATURE OR FUNCTION N/A AESC Disable w/ Brake Pedal:7511 1, ENABLE FEATURE OR FUNCTION N/A AESC Accel Pedal Mode:7513 1, AESC OVERRIDDEN BY ACCELERATOR PEDAL N/A AESC Max Engine Load:7519 100.0000 % AESC Control to Engine Load:7530 0, KICK OUT OF AESC ABOVE PROGRAMMED LIMIT N/A AESC Max Engine Load Time:7527 8 SEC AESC Vehicle Speed Limit:7521 5.0000 MPH AESC Max Mobile Veh Spd:7501 5 MPH AESC Eng Spd Limit w/VSS Fault:7518 1500 RPM AESC Force Fan On:9007 0, DISABLE FEATURE OR FUNCTION N/A AESC Park Brake Override:7534 1, ENABLE FEATURE OR FUNCTION N/A AESC Transfer Case Signal Mode:8910 0, DRIVELINE N/A AESC Splitshaft Veh SPD Dsply:9307 0, SPEED SENSOR LOCATED IN WHEEL RIM N/A AESC Remote Accel Pedal Enable:7504 0, DISABLE FEATURE OR FUNCTION N/A AESC Remote Accel Pedal Switch:8914 0, DISABLE FEATURE OR FUNCTION N/A AESC Accel Max Eng Spd Ovrd:7520 1900.0 RPM Rem Accelerator Switch Input:9929 1, SAE J1939 MULTIPLEXED N/A Preset Remote AESC Input Type:9932 0, DISCRETE (HARDWIRED) INPUT N/A Variable Remote AESC Input:9933 0, DISCRETE (HARDWIRED) INPUT N/A Rem Accelerator Position Input:9935 1, SAE J1939 MULTIPLEXED N/A Engine Protection Mode:7700 1, TWO WAY WARNING (OIL PRES, WATER TEMP) N/A Powertrain Protection Enable:7722 0, DISABLE FEATURE OR FUNCTION N/A Torque Limiting in Gear:7717 0, DISABLE FEATURE OR FUNCTION N/A Highest Gear of Low Range:7718 2 N/A Highest Gear Rat of Low Range:7745 6.00 N/A Highest Gear of Int. Range:7748 4 N/A Highest Gear Rat of Int. Range:7746 4.00 N/A Highest Gear of High Range:7749 6 N/A Highest Gear Rat of High Range:7747 2.00 N/A Max Torque in Low Gear Range:7713 1450.0000 LB-FT Max Torque in Int. Gear Range:7750 1450.0000 LB-FT Max Torque in High Gear Range:7751 1450.0000 LB-FT VSS Anti-Tamper Max Eng Speed:7901 1504.9 RPM Auxilllary Shutdown Input Type:9931 0, DISCRETE (HARDWIRED) INPUT N/A Veh Speed Sensor Antitampering:7905 0, DISABLE FEATURE OR FUNCTION N/A Veh Overspd Threshold Level 1:7723 79.480131 MPH Veh Overspd Threshold Level 2:7724 81.480131 MPH Service Interval Enable 0, DISABLE FEATURE OR FUNCTION N/A Fuel Used Service Interval:9501 0 GALLONS Engine Hour Service Interval:9502 0 HOURS Veh Distance Service Interval:9503 0 MILES Service Soon Percent to Notify:9507 90 % Customer Unit Number:6605 0 N/A Hard Braking Incident Counter:8904 1, ENABLE FEATURE OR FUNCTION N/A Hard Braking Decel Threshold:8905 7.40 MPH/SEC

Page 21: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Vehicle Over-speed Indicator:7754 0, FEATURE OR FUNCTION IS DISABLED N/A Customer Password:8700 00000000 N/A These Electronic Parameters have not been finalized

Page 22: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

H-GAC Product Code: B4 CT660-LTA, TRA, 122” BBC (CF7AB), Tractor Configuration

Model Profile 2015 CT660L SBA 6x4 (CF7AB) APPLICATION: On-Off Highway Tractor - General MISSION: Requested GCWR: 80000. Calc. GVWR: 52350 Calc. Start / Grade Ability: 21.70% / 1.94% @ 55 MPH Calc. Geared Speed: 64.9 MPH FUEL ECONOMY: 5.61 MPG @ 55 MPH DIMENSION: Wheelbase: 181.00, CA: 113.00, Axle to Frame: 57.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FR-14210B} 10-Speed Manual, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 3.90 CAB: Conventional TIRE, FRONT: (2) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply TIRE, REAR: (8) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KU Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description CF7AB00 Base Chassis, Model CT660L SBA 6x4 with 181.00 Wheelbase, 113.00 CA, and 57.00 Axle to Frame. 1616 FRAME RAILS WITH TAPERED REAR 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 1LBC BUMPER, FRONT Multi-piece Stainless Steel Includes : FOG LIGHT OPENING (2) and with Rectangular Hole for Step 1WVX WHEELBASE RANGE 181" (460cm) Through and Including 234" (595cm) 2ASG AXLE, FRONT NON-DRIVING {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity 3ACH SUSPENSION, FRONT, SPRING Multileaf, Shackle Type; 14,000-lb Capacity; With Shock Absorbers Includes : SPRING PINS Threaded 4092 BRAKE SYSTEM, AIR Dual System for Tractor Applications Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : GLAD HANDS (2) One for Service and One for Emergency; Trailer Hoses from Cab : HAND CONTROL VALVE, AIR Mounted on Steering Column : HOSE TENDER Back of Cab Mounted : PARKING BRAKE CONTROL Yellow and Red Knobs, Located on Instrument Panel : PARKING BRAKE VALVE Combination Valve for Tractor and Trailer : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for Forward Rear Axle : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic : SWITCH, AUXILIARY Interrupter for Cab and Trailer Clearance/Marker Lights (Blinks Lights with Headlight Switch in "ON" Position); Instrument Panel Mounted : TRACTOR PROTECTION VALVE : TRAILER HOSES AND CABLES 15' Coiled Lighting Cable with 7-Way Connector and with 15' Coiled Nylon Brake Hose Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4193 BRAKES, FRONT, AIR CAM 16.5" x 6", Includes 24 SqIn Long Stroke Brake Chambers 4732 DRAIN VALVE {Berg} Manual; With Pull Chain, for Air Tank Includes : DRAIN VALVE Mounted in Wet Tank 4774 SPECIAL RATING, GAWR Provides Rear Tractor Brake Rating Equal to Axle Rating up to 23,000-lbs for Single Axles, 46,000-lbs for Tandem Axles, or 69,000-lb for Tridem

Page 23: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4AAB BRAKE CHAMBERS, ADDITIONAL (2) {Haldex} Spring Brake Type; 30/30 SqIn Includes : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 Additional for Rear Rear Axle 4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel) Code Description 4EBS AIR DRYER {Bendix AD-9} With Heater Includes : AIR DRYER LOCATION Inside Left Rail, Back of Cab 4ETE BRAKE CHAMBERS, FRONT AXLE {Haldex} 24 SqIn 4EVL BRAKE CHAMBERS, REAR AXLE {Haldex GC3030LHDHO} 30/30 Spring Brake 4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.In. Long Stroke Brake Chamber and Spring Actuated Parking Brake 4SPM AIR COMPRESSOR {Bendix BA-921 Head Unload} 15.9 CFM Capacity, Single Cylinder 4WCC BRAKE PACKAGE, FRONT {Dana Spicer ES-165-6} Air, Cam Type, Extended Service; Size 16.5" x 6", Includes Automatic Slack Adjusters 4WCD BRAKE PACKAGE, REAR {Dana Spicer ES-165-7} Air, Cam Type, Extended Service; Size 16.5" x 7", Includes Automatic Slack Adjusters 5710 STEERING COLUMN Tilting and Telescoping 5PSA STEERING GEAR {Sheppard M-100} Power 5WBH STEERING WHEEL {Caterpillar} 2-Spoke, 18" Diam., Dark Neutral, Leather Wrapped 7BJU EXHAUST SYSTEM Switchback Horizontal Aftertreatment Device, Frame Mounted Right Side Under Cab; Includes Single Vertical Tail Pipe & Guard, Right Side, Cab Mounted 8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment Includes : BATTERY BOX Aluminum : CIGAR LIGHTER Includes Ash Cup, Center Console Mounted : FUSES, ELECTRICAL SAE Blade-Type : HAZARD SWITCH Integral with Turn Signal Switch : HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever : HEADLIGHTS (2) Composite with Halogen Projector Beam : HORN, AIR Single, Chrome : HORN, ELECTRIC Single : PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light : READING LIGHT, CAB (2) with Individual Switches; One Above Each Door : STARTER SWITCH Electric, Key Operated : STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector : TURN SIGNAL FLASHER : TURN SIGNAL SWITCH Manual Cancelling with Lane Change Feature : TURN SIGNALS, FRONT Includes Integral Reflectors and Side Marker Lights; Fender Mounted : WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature, Steering Column Mounted : WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted : WIRING, CHASSIS Color Coded and Continuously Numbered 8653 HORN, AIR Single, Located Under Cab 8718 POWER SOURCE Cigar Type Receptacle without Plug and Cord 8GGN ALTERNATOR {Bosch LH160} Brush Type, 12 Volt 160 Amp. Capacity, Pad Mount 8MMJ BATTERY SYSTEM {Caterpillar} (3) 12 Volt 2130CCA Total 8RMD RADIO AM/FM/WB/Clock/3MM Auxiliary Input, with Multiple Speakers 8RMG ANTENNA BASE (2) Single Function, (1) for CB and (1) for Entertainment Radio, Without Splitter, Separate Lead-Ins, With CB Antenna Mounted on Left Mirror and AM/FM Antenna Mounted on Right Mirror 8WCK POWER SOURCE, TERMINAL TYPE 2-Post Code Description 8WEZ TURN SIGNAL SWITCH Self-Canceling 8WKH BATTERY BOX Aluminum with Aluminum Cover, 18" Wide, 2, 3 or 4 Battery Capacity, Mounted Right Side Back of Cab 8WNH RUNNING LIGHT (2) Daytime 8WXG STARTING MOTOR {Mitsubishi Electric Automotive America 105P} 12-Volt, with Soft-Start 9ASE FRONT END Tilting Composite Includes : GRILLE SURROUND Brushed Stainless Steel 9HAN INSULATION, UNDER HOOD for Sound Abatement 9HBN INSULATION, SPLASH PANELS for Sound Abatement 10060 PAINT SCHEMATIC, PT-1 Single Color, Design 100 10761 PAINT TYPE Base Coat/Clear Coat, 1-2 Tone 10769 PAINT CLASS Premium Color 10EYC FIFTH WHEEL, STATIONARY {Fontaine SL7FMA-D69-3} Cast Top Plate; 8.69" Above Top of Frame; Left Hand Roadside Release

Page 24: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

10WPR MUD FLAP HOLDER Spring Loaded, Painted Black; With Red and White Reflective Tape; Less Flaps 10WPY MUD FLAPS, REAR Black Rubber, Anti-Sail Less Logo; Less Holders 11MGZ CLUTCH {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity Includes : CLUTCH RELEASE BEARING Greasable 12KXP ENGINE, DIESEL {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) 12THT FAN DRIVE {Horton Drivemaster} Direct Drive Type, Two Speed With Residual Torque Device for Disengaged Fan Speed 12UBH RADIATOR Aluminum; Welded, Front to Back Down Flow System, 1564 SqIn, 1572 SqIn Dual CAC, 1293 SqIn 3 Core LTR 12VBT AIR CLEANER Single Element, Heavy Duty 12VED FEDERAL EMISSIONS for 2010; CT 13 Engines 12WCX HOSE CLAMPS, RADIATOR HOSES {Gates} Shrink Band Type 12WEG COLD STARTING EQUIPMENT Automatic; With Engine ECM Control 12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, Engine Mounted 12WZJ EMISSION COMPLIANCE Low NOx Idle Engine, Complies with California Clean Air Regulations; Includes "Certified Clean Idle" Decal located on Driver Door 12XAN OBD COMPLIANCE for 2013 OBD (On Board Diagnostics) 13GHJ TRANSMISSION, MANUAL {Fuller FR-14210B} 10-Speed Manual, With Air Shift Includes : CLUTCH BRAKE Torque Limiting : FILL PLUG, MAGNETIC Code Description 13WAP TRANSMISSION LUBE PUMP for International, Fuller, Meritor or Spicer Transmissions; USE ONLY WHEN PUMP IS NOT INCLUDED STANDARD IN TRANSMISSION 13WGJ OIL COOLER,MANUAL TRANSMISSION Water to Oil Type Included in Radiator End Tank (REQUIRES TRANSMISSION LUBE PUMP) 13WLB TRANSMISSION OIL {EmGard 50W} Synthetic; 22 thru 33.99 Pints 14GVU AXLE, REAR, TANDEM {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Lube Oil Pump . Gear Ratio: 3.90 Includes : POWER DIVIDER LOCK Air Operated, Cab Control with Indicator Light in Cluster : REAR AXLE DRAIN PLUG (2) Magnetic, For Tandem Rear Axle 14ULX SUSPENSION, REAR, TANDEM {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000- lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers Includes : CROSSMEMBER, SUSPENSION Stamped Steel Double Dogbone Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 14WAL SUSPENSION/REAR-AXLE IDENTITY for Meritor Tandem Rear Axles With Bar-Pin Beam Attachment Type Suspensions 14WBV SHOCK ABSORBERS, REAR (4) for Hendrickson HMX Suspension Only, Mounted from Frame to Beam 14WLD AXLE, REAR, LUBE {EmGard 75W-90} Synthetic Oil; 50 thru 64.99 Pints 15DYP DEF TANK 9.5 U.S. Gal. 36.0L Capacity, Frame Mounted Outside Left Rail, Under Cab 15LKU FUEL/WATER SEPARATOR {Racor} Fuel Pre-Filter and Filter Base, Includes Water-In-Fuel Sensor 15SGL FUEL TANK Non-Polished Aluminum, 24" Diam., 80 U.S. Gal., 302 L Capacity Mounted Left Side Under Cab 16031 CAB Conventional Includes : COAT HOOK, CAB Located on Rear Wall, Behind Passenger Seat : CONSOLE, CENTER Plastic, Driver Convenience with a Cup and Change Holder, Ash Tray and Lower Storage Area : DOME LIGHT, CAB (2) Driver and Passenger Dome Lights with Individual Switches, in Headliner : DOOR CHECK STRAP (2) One Each Door : GLASS, ALL WINDOWS Tinted : GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side : GRAB HANDLE, EXTERIOR (2) Mounted Behind Driver and Passenger Doors : INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color : SKIN Riveted : STEP (4) Two Steps Per Door 16400 SEAT, PASSENGER Omit Item 16HBA GAUGE CLUSTER English With English Electronic Speedometer 16JPC SEAT, DRIVER {National 2000 Model 295} Air Suspension, Intermediate Back, All Vinyl, 2 Arm Rests, Isolator, 7" Adjuster, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, 3 Position Rear Cushion, 2-15 Degree Back Angle Adjust, Vinyl Suspension Cover 16SKS MIRRORS (2) {Lang Mekra} Aero; Rectangular, 7.09" x 15.75" & Integral Convex Both Sides, 102" Inside Spacing, Breakaway Type, Heated Heads Thermostat Controlled, Amber Lens Clearance Light LED, Black

Page 25: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Painted Finish Heads, Brackets & Arms Code Description 16VRT HEATER, ENHANCED CIRCULATION {Bergstrom} Control, for Extreme Cold Weather Climates 16VTH CAB INTERIOR TRIM Premium Level; for Caterpillar, Day Cab Includes : "A" PILLAR COVER Molded Plastic : CAB INTERIOR TRIM PANELS Vinyl : CONSOLE, OVERHEAD Molded Plastic with Three Storage Pockets; One with Strap for CB Radio Mounting; Two with Netting, Courtesy Lights with Switches : COURTESY LIGHT (2) Driver and Passenger Door Mounted : DOOR TRIM PANELS Vinyl Upper with Power Locks and Windows, Upper and Lower Grab Handles, Both Sides : FLOOR COVERING Rubber, Black : HEADLINER Soft Padded Vinyl : HEATER BOX Metal, Painted Black : INSTRUMENT PANEL TRIM Vinyl : MIRROR, CONVEX, LOOK DOWN Black Finish; 6" x 10-1/4"; Located on Passenger Side : STORAGE POCKET, DOOR (2) Driver and Passenger Door : SUN VISOR (2) Vinyl with Molded Toll Ticket Retainer 16VZA WINDOW, REAR 52.25" Wide 16WAK WINDOW, POWER (2) in Left and Right Doors 16WJG CAB DOOR LOCKS Power 16WKB AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster 16WKR WINDSHIELD Single Piece 16WLD CAB REAR SUSPENSION {Link Z9079D1} Dual Frame Mounted Cab Rear Air Suspension; Includes Special Crossmember Assembly 16XWD SUNSHADE, EXTERIOR Aerodynamic, Painted Roof Color; Includes Integral Clearance/Marker Lights 27DMD WHEELS, FRONT DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Aluminum Hubs 28DMD WHEELS, REAR DUAL DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Aluminum Hubs. 7372135415 (2) TIRE, FRONT 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply 7372135415 (8) TIRE, REAR 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply 810000 FIFTH WHEEL LOCATION On Rear Axle Centerline Graphics are provided as visual aids only and are not intended to represent the actual scale, shape, or color of the truck or its components. All weights are represented in lbs. Truck Body/Trailer Chassis/Empty Weights Bumper to Axle (BA) 54.0 Wheelbase (WB)181.00 Axle to Frame (AF) 57.00 Axle to Back Cab (ABC) 68 Cab to Axle (CA) 113 Usable CA 113 CA Reduction Adjustment 0 Fuel-Diesel(Gals) 50 DEF(Gals) 0 Trailer Length (TL) 540 5th Wheel Position (FW) 0 5th Wheel to Axle (FWA) 444 Trailer Wheelbase 444 Nose of Trailer to KP (KP) 36 Axle to Back of Trailer (AB) 60 Tractor Front Axle: 9,557 Tractor Rear Axle: 7,527 Trailer King Pin: 1,500 Trailer Rear Axle: 3,500 Payloads Before the Cab Cab Chassis Body After the Body # Weight CG # Weight CG # Weight CG # Weight CG # Weight CG 1 26,000 81 2 28,500 465 Loads Weight Distribution Payload Weight: 54,500 Driver: 250 Fuel-Diesel(Lbs): 355 DEF(Lbs): 0 Total Front Axle: 9,910 Total Rear Axle: 33,607

Page 26: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Total Rear Trailer: 33,672 Total Weight: 77,189 Weights and clearances in this proposal are estimates only. Neither Caterpillar nor its suppliers are liable for any consequences resulting from any differences between the estimated weights and clearances and the actual manufactured weights and clearances. Weight Distribution All weights are represented in lbs. 0"off centerline Tractor Trailer Front Rear Rear Total Chassis Weight Chassis Weight: 9,557 7,527 0 17,084 Fuel: 165 190 0 355 DEF: 0 0 0 0 Empty Trailer: 0 1,500 3,500 5,000 (Curb Weight): 9,722 9,217 3,500 22,439 Loads Payloads: 0 24,328 30,172 54,500 Driver: 188 62 0 250 Axle Totals (Gross Weight): 9,910 33,607 33,672 77,189 Weight Ratings Tractor Trailer Front Rear Rear Axle(axle capacity) 13,200 40,000 Tire(tire capacity) 12,350 46,720 Suspension(suspension capacity) 14,000 40,000 Spring: 0 Fed Bridge Law (axle spread): 20,000 34,000 (54") 34,000 (48") Wheel Combination Load Limit 1 - 3 43,517 48,500 2 - 5 67,279 69,500 1 - 5 77,189 81,500 Federal Total Vehicle Weight Limit: 80,000 Maximum Gross Vehicle Weight Rating (GVWR) 52,350 - Gross Vehicle Weight(GVW) 43,517 = 8,833 Reserves Weight Summary * Distributed weights are within capacity limits ENGINE, DIESEL (0012KXP) ATTACHMENTS: 0016HBA (GAUGE CLUSTER) 0015LKU (FUEL/WATER SEPARATOR) 0012WEG (COLD STARTING EQUIPMENT) 0012THT (FAN DRIVE) Parameter Value UOM Max Accelerator Vehicle Speed:7902 65 MPH Vehicle Speed Limiter Override:7911 0, DISABLE FEATURE OR FUNCTION N/A VSLO Speed Increment:7912 10 MPH VSLO Maximum Activation Time:7914 30 MIN VSLO Time Interval to Reset:7915 8.0 HOURS VSLO Time Duration Source:7934 1, INTERVAL BASED ON REAL TIME CLOCK N/A Progressive Shift Enable:7744 0, DISABLE FEATURE OR FUNCTION N/A Low Gear Ratio Break Point:7742 7.029500 N/A High Gear Ratio Break Point:7743 2.133000000 N/A Low Gear Engine Speed Limit:7738 1550.0 RPM High Gear Engine Speed Limit:7739 1600.0 RPM Low Gear Engine Speed Range:7740 200.0 RPM High Gear Engine Speed Range:7741 200.0 RPM Min Gear Ratio for ProShift:7755 0.50 N/A Gear Down Protection Enable:7714 0, DISABLE FEATURE OR FUNCTION N/A Top Gr Minus 2 Light Ld VS Lim:7715 25 MPH Top Gr Minus 1 Light Ld VS Lim:7716 34 MPH Top Gr Minus 2 Heavy Ld VS Lim:7735 28 MPH Top Gr Minus 1 Heavy Ld VS Lim:7736 37 MPH Driver Reward Enable:7918 0, DISABLE FEATURE OR FUNCTION N/A Driver Reward Mode:7930 2, BOTH ACCELERATOR AND CRUISE VEHICLE SPEED LIMIT INCREASE N/A Driver Reward Performance Crit:7925 0, FUEL ECONOMY BASED REWARD SYSEM N/A Fuel Economy - Expected Level:7921 6.00 MPG Fuel Economy - Good Level:7920 6.25 MPG

Page 27: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Fuel Economy - Excellent Level:7919 6.40 MPG % Idle Time - Expected Level:7924 25 % % Idle Time - Good Level:7923 18 % % Idle Time - Excellent Level:7922 10 % Driver Reward Ambient Temp H:7938 150.0 C Driver Reward Ambient Temp L:7939 -40.0 C VS Lim Increase - Expected Lvl:7926 0 MPH VS Lim Increase - Good Lvl:7927 2 MPH VS Lim Increase - Excel Lvl:7928 4 MPH VS Lim Decrease - Penalty Lvl:7929 -2 MPH Idle Engine Speed:8202 600.0 RPM Idle Speed Adjustment Enable:8215 1, ENABLE FEATURE OR FUNCTION N/A Idle Spd Adjust - Max Eng Spd:8212 0.0 RPM Idle Spd Adjust - Bump Step:8216 5.0 RPM Idle Spd Adjust Ramp Rate:8211 25 RPM/SEC Maximum Standstill Eng Speed:7753 2100.0 RPM Idle Shutdown Mode:7400 0, DISABLE FEATURE OR FUNCTION N/A ISD Time w/Park Brk Released:7401 15.0 MIN ISD Time w/Park Brake Set:7404 5.0 MIN ISD Latched Driver Override En:7407 0, DISABLE FEATURE OR FUNCTION N/A ISD Ambient Temp Override En:7408 0, DISABLE FEATURE OR FUNCTION N/A ISD Int Amb Temp Enable:7405 0, DISABLE FEATURE OR FUNCTION N/A ISD Max Ambient Temp Override:7402 20.0 C ISD Int Amb Temp Override:7406 15.0 C ISD Min Ambient Temp Override:7403 5.0 C ISD Max Engine Coolant Temp:7412 150.0 C ISD Min Engine Coolant Temp:7413 16.0 C ISD Idle Shutdown Max Eng Trq:7409 80 % Cruise Control Enable:7600 1, ENABLE FEATURE OR FUNCTION N/A Electronic Parameters Summary CC Max Vehicle Speed:7604 65 MPH CC Min Vehicle Speed:7603 25.0000 MPH AESC Control:7500 0, DISABLE FEATURE OR FUNCTION N/A AESC In-cab Mode:7502 2, VARIABLE ENGINE SPEED CONTROL SELECTED N/A AESC Min Engine Speed:7522 600.0 RPM AESC Max Engine Speed:7508 1500.0 RPM AESC Preset Engine Speed 1:7505 800.0 RPM AESC Preset Engine Speed 2:7506 900.0 RPM AESC Preset Engine Speed 3:7514 1000.0 RPM AESC Preset Engine Speed 4:7515 1100.0 RPM AESC Preset Engine Speed 5:7516 1200.0 RPM AESC Preset Engine Speed 6:7517 1300.0 RPM AESC Activate at Preset Speed:7528 0, NO PRESET PRESELECTION N/A AESC Ramp Up Rate:7507 100.00 RPM/SEC AESC Ramp Down Rate:7524 100.00 RPM/SEC AESC Bump Up/Down Step:7525 25.0 RPM AESC In-cab Operator Interface:7503 0, NO (OFF) OR DISABLE N/A AESC Disable w/ Clutch Pedal:7510 1, ENABLE FEATURE OR FUNCTION N/A AESC Disable w/ Brake Pedal:7511 1, ENABLE FEATURE OR FUNCTION N/A AESC Accel Pedal Mode:7513 1, AESC OVERRIDDEN BY ACCELERATOR PEDAL N/A AESC Max Engine Load:7519 100.0000 % AESC Control to Engine Load:7530 0, KICK OUT OF AESC ABOVE PROGRAMMED LIMIT N/A AESC Max Engine Load Time:7527 8 SEC AESC Vehicle Speed Limit:7521 5.0000 MPH AESC Max Mobile Veh Spd:7501 5 MPH AESC Eng Spd Limit w/VSS Fault:7518 1500 RPM AESC Force Fan On:9007 0, DISABLE FEATURE OR FUNCTION N/A AESC Park Brake Override:7534 1, ENABLE FEATURE OR FUNCTION N/A AESC Transfer Case Signal Mode:8910 0, DRIVELINE N/A AESC Splitshaft Veh SPD Dsply:9307 0, SPEED SENSOR LOCATED IN WHEEL RIM N/A AESC Remote Accel Pedal Enable:7504 0, DISABLE FEATURE OR FUNCTION N/A AESC Remote Accel Pedal Switch:8914 0, DISABLE FEATURE OR FUNCTION N/A AESC Accel Max Eng Spd Ovrd:7520 1900.0 RPM Rem Accelerator Switch Input:9929 1, SAE J1939 MULTIPLEXED N/A Preset Remote AESC Input Type:9932 0, DISCRETE (HARDWIRED) INPUT N/A Variable Remote AESC Input:9933 0, DISCRETE (HARDWIRED) INPUT N/A Rem Accelerator Position Input:9935 1, SAE J1939 MULTIPLEXED N/A Engine Protection Mode:7700 1, TWO WAY WARNING (OIL PRES, WATER TEMP) N/A Powertrain Protection Enable:7722 0, DISABLE FEATURE OR FUNCTION N/A

Page 28: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Torque Limiting in Gear:7717 0, DISABLE FEATURE OR FUNCTION N/A Highest Gear of Low Range:7718 2 N/A Highest Gear Rat of Low Range:7745 6.00 N/A Highest Gear of Int. Range:7748 4 N/A Highest Gear Rat of Int. Range:7746 4.00 N/A Highest Gear of High Range:7749 6 N/A Highest Gear Rat of High Range:7747 2.00 N/A Max Torque in Low Gear Range:7713 1450.0000 LB-FT Max Torque in Int. Gear Range:7750 1450.0000 LB-FT Max Torque in High Gear Range:7751 1450.0000 LB-FT VSS Anti-Tamper Max Eng Speed:7901 1716.1 RPM Auxilllary Shutdown Input Type:9931 0, DISCRETE (HARDWIRED) INPUT N/A Veh Speed Sensor Antitampering:7905 0, DISABLE FEATURE OR FUNCTION N/A Veh Overspd Threshold Level 1:7723 70.374884 MPH Veh Overspd Threshold Level 2:7724 72.374884 MPH Service Interval Enable 0, DISABLE FEATURE OR FUNCTION N/A Fuel Used Service Interval:9501 0 GALLONS Engine Hour Service Interval:9502 0 HOURS Veh Distance Service Interval:9503 0 MILES Service Soon Percent to Notify:9507 90 % Customer Unit Number:6605 0 N/A Hard Braking Incident Counter:8904 1, ENABLE FEATURE OR FUNCTION N/A Hard Braking Decel Threshold:8905 7.40 MPH/SEC Vehicle Over-speed Indicator:7754 0, FEATURE OR FUNCTION IS DISABLED N/A Customer Password:8700 00000000 N/A These Electronic Parameters have been successfully finalized

Page 29: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

H-GAC Product Code: B5 CT681-SG-SFA, Conv. Cab, TRA, 114" BBC (CF6AA)

Model Profile 2015 CT681SG SFA 6x4 (CF6AA) APPLICATION: Utility/Service (Other) MISSION: Requested GVWR: 52000. Calc. GVWR: 52000 Calc. Start / Grade Ability: 27.20% / 2.34% @ 55 MPH Calc. Geared Speed: 83.2 MPH FUEL ECONOMY: 7.91 MPG @ 55 MPH DIMENSION: Wheelbase: 189.00, CA: 103.00, Axle to Frame: 53.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 365 HP @ 1700 RPM, 1250 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 365 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FRO-12210C} 10-Speed Manual, With Overdrive, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor FF-961} I-Beam Type, 12,000-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 4.11 CAB: Conventional TIRE, FRONT: (2) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply TIRE, REAR: (8) 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KV Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description CF6AA00 Base Chassis, Model CT681SG SFA 6x4 with 189.00 Wheelbase, 103.00 CA, and 53.00 Axle to Frame. 1652 CROSSMEMBER, REAR Relocated to End of Frame 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 1LMU BUMPER, FRONT Flat Face, Gull Wing, Steel, 15.5" High x 94.0 Long 1WWX WHEELBASE RANGE 161" (410cm) Through and Including 205" (520cm) 2ARA AXLE, FRONT NON-DRIVING {Meritor FF-961} I-Beam Type, 12,000-lb Capacity 3ADC SUSPENSION, FRONT, SPRING Parabolic, Taper Leaf; 12,000-lb Capacity; With Shock Absorbers 4091 BRAKE SYSTEM, AIR Dual System for Straight Truck Applications Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : DUST SHIELDS, FRONT BRAKE : DUST SHIELDS, REAR BRAKE : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : INVERSION VALVE Bendix SR-1 and Double Check Valve : PARKING BRAKE CONTROL Yellow Knob, Located on Instrument Panel : PARKING BRAKE VALVE For Truck : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for 4x2, 2 for 6x4 : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic : SWITCH, AUXILIARY Interrupter for Cab Clearance/Marker Lights (Blinks Lights with Headlight Switch in "ON" Position); Instrument Panel Mounted Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4732 DRAIN VALVE {Berg} Manual; With Pull Chain, for Air Tank Includes : DRAIN VALVE Mounted in Wet Tank 4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel) 4EBS AIR DRYER {Bendix AD-9} With Heater Includes : AIR DRYER LOCATION Inside Left Rail, Back of Cab 4ESX BRAKE CHAMBERS, FRONT AXLE {Haldex} 20 SqIn 4EVL BRAKE CHAMBERS, REAR AXLE {Haldex GC3030LHDHO} 30/30 Spring Brake 4JCJ BRAKES, FRONT, AIR CAM S-Cam; 16.5" x 5.0"; Includes 20 Sq. In. Long Stroke Brake Chambers 4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.In. Long Stroke Brake Chamber and Spring Actuated Parking Brake 4SPM AIR COMPRESSOR {Bendix BA-921 Head Unload} 15.9 CFM Capacity, Single Cylinder 5710 STEERING COLUMN Tilting and Telescoping

Page 30: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

5PSA STEERING GEAR {Sheppard M-100} Power 5WBH STEERING WHEEL {Caterpillar} 2-Spoke, 18" Diam., Dark Neutral, Leather Wrapped Code Description 7BJU EXHAUST SYSTEM Switchback Horizontal Aftertreatment Device, Frame Mounted Right Side Under Cab; Includes Single Vertical Tail Pipe & Guard, Right Side, Cab Mounted 8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment Includes : BATTERY BOX Aluminum : CIGAR LIGHTER Includes Ash Cup, Center Console Mounted : FUSES, ELECTRICAL SAE Blade-Type : HAZARD SWITCH Integral with Turn Signal Switch : HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever : HEADLIGHTS (2) Composite with Halogen Projector Beam : HORN, AIR Single, Chrome : HORN, ELECTRIC Single : PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light : READING LIGHT, CAB (2) with Individual Switches; One Above Each Door : STARTER SWITCH Electric, Key Operated : STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector : TURN SIGNAL FLASHER : TURN SIGNAL SWITCH Manual Cancelling with Lane Change Feature : TURN SIGNALS, FRONT Includes Integral Reflectors and Side Marker Lights; Fender Mounted : WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature, Steering Column Mounted : WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted : WIRING, CHASSIS Color Coded and Continuously Numbered 8653 HORN, AIR Single, Located Under Cab 8718 POWER SOURCE Cigar Type Receptacle without Plug and Cord 8GGN ALTERNATOR {Bosch LH160} Brush Type, 12 Volt 160 Amp. Capacity, Pad Mount 8MMJ BATTERY SYSTEM {Caterpillar} (3) 12 Volt 2130CCA Total 8RMD RADIO AM/FM/WB/Clock/3MM Auxiliary Input, with Multiple Speakers 8RMG ANTENNA BASE (2) Single Function, (1) for CB and (1) for Entertainment Radio, Without Splitter, Separate Lead-Ins, With CB Antenna Mounted on Left Mirror and AM/FM Antenna Mounted on Right Mirror 8VUK BATTERY BOX Aluminum With Plastic Cover, 18" Wide, 2, 3, or 4 Battery Capacity, Mounted Right Side Back of Cab 8WCK POWER SOURCE, TERMINAL TYPE 2-Post 8WNH RUNNING LIGHT (2) Daytime 8WXG STARTING MOTOR {Mitsubishi Electric Automotive America 105P} 12-Volt, with Soft-Start 9ANC FRONT END Tilting, Fiberglass; With Stationary Grille 9HAN INSULATION, UNDER HOOD for Sound Abatement 9HBN INSULATION, SPLASH PANELS for Sound Abatement 10060 PAINT SCHEMATIC, PT-1 Single Color, Design 100 10761 PAINT TYPE Base Coat/Clear Coat, 1-2 Tone 10769 PAINT CLASS Premium Color 11MGZ CLUTCH {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity Includes : CLUTCH RELEASE BEARING Greasable Code Description 12KXL ENGINE, DIESEL {CT 13} EPA 10, SCR, 365 HP @ 1700 RPM, 1250 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 365 Peak HP (Max) 12THT FAN DRIVE {Horton Drivemaster} Direct Drive Type, Two Speed With Residual Torque Device for Disengaged Fan Speed 12UBV RADIATOR Aluminum: Welded, Front to Back Down Flow System, 1177 SqIn, 825 SqIn CAC, 949 SqIn 3 Core LTR 12VBC AIR CLEANER Single Element 12VED FEDERAL EMISSIONS for 2010; CT 13 Engines 12WCX HOSE CLAMPS, RADIATOR HOSES {Gates} Shrink Band Type 12WEG COLD STARTING EQUIPMENT Automatic; With Engine ECM Control 12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, Engine Mounted 12WZB EMISSION COMPLIANCE Low NOx Idle Engine, Complies with California Clean Air Regulations; Includes "Certified Clean Idle" Decal on Hood 12XAN OBD COMPLIANCE for 2013 OBD (On Board Diagnostics) 13GGV TRANSMISSION, MANUAL {Fuller FRO-12210C} 10-Speed Manual, With Overdrive, With Air Shift Includes : CLUTCH BRAKE Torque Limiting : FILL PLUG, MAGNETIC 13WLB TRANSMISSION OIL {EmGard 50W} Synthetic; 22 thru 33.99 Pints 14GVU AXLE, REAR, TANDEM {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Lube Oil Pump . Gear Ratio: 4.11

Page 31: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Includes : POWER DIVIDER LOCK Air Operated, Cab Control with Indicator Light in Cluster : REAR AXLE DRAIN PLUG (2) Magnetic, For Tandem Rear Axle 14ULX SUSPENSION, REAR, TANDEM {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000- lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers Includes : CROSSMEMBER, SUSPENSION Stamped Steel Double Dogbone Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 14WAL SUSPENSION/REAR-AXLE IDENTITY for Meritor Tandem Rear Axles With Bar-Pin Beam Attachment Type Suspensions 14WLD AXLE, REAR, LUBE {EmGard 75W-90} Synthetic Oil; 50 thru 64.99 Pints 15DYP DEF TANK 9.5 U.S. Gal. 36.0L Capacity, Frame Mounted Outside Left Rail, Under Cab 15LKU FUEL/WATER SEPARATOR {Racor} Fuel Pre-Filter and Filter Base, Includes Water-In-Fuel Sensor 15SGL FUEL TANK Non-Polished Aluminum, 24" Diam., 80 U.S. Gal., 302 L Capacity Mounted Left Side Under Cab 16031 CAB Conventional Includes : COAT HOOK, CAB Located on Rear Wall, Behind Passenger Seat : CONSOLE, CENTER Plastic, Driver Convenience with a Cup and Change Holder, Ash Tray and Lower Storage Area Code Description : DOME LIGHT, CAB (2) Driver and Passenger Dome Lights with Individual Switches, in Headliner : DOOR CHECK STRAP (2) One Each Door : GLASS, ALL WINDOWS Tinted : GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side : GRAB HANDLE, EXTERIOR (2) Mounted Behind Driver and Passenger Doors : INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color : SKIN Riveted : STEP (4) Two Steps Per Door 16400 SEAT, PASSENGER Omit Item 16564 HEATER SHUT-OFF VALVES (1) Ball Check Valve Type, Supply Line 16HBA GAUGE CLUSTER English With English Electronic Speedometer 16JPC SEAT, DRIVER {National 2000 Model 295} Air Suspension, Intermediate Back, All Vinyl, 2 Arm Rests, Isolator, 7" Adjuster, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, 3 Position Rear Cushion, 2-15 Degree Back Angle Adjust, Vinyl Suspension Cover 16SKS MIRRORS (2) {Lang Mekra} Aero; Rectangular, 7.09" x 15.75" & Integral Convex Both Sides, 102" Inside Spacing, Breakaway Type, Heated Heads Thermostat Controlled, Amber Lens Clearance Light LED, Black Painted Finish Heads, Brackets & Arms 16VRT HEATER, ENHANCED CIRCULATION {Bergstrom} Control, for Extreme Cold Weather Climates 16VTH CAB INTERIOR TRIM Premium Level; for Caterpillar, Day Cab Includes : "A" PILLAR COVER Molded Plastic : CAB INTERIOR TRIM PANELS Vinyl : CONSOLE, OVERHEAD Molded Plastic with Three Storage Pockets; One with Strap for CB Radio Mounting; Two with Netting, Courtesy Lights with Switches : COURTESY LIGHT (2) Driver and Passenger Door Mounted : DOOR TRIM PANELS Vinyl Upper with Power Locks and Windows, Upper and Lower Grab Handles, Both Sides : FLOOR COVERING Rubber, Black : HEADLINER Soft Padded Vinyl : HEATER BOX Metal, Painted Black : INSTRUMENT PANEL TRIM Vinyl : MIRROR, CONVEX, LOOK DOWN Black Finish; 6" x 10-1/4"; Located on Passenger Side : STORAGE POCKET, DOOR (2) Driver and Passenger Door : SUN VISOR (2) Vinyl with Molded Toll Ticket Retainer 16VZA WINDOW, REAR 52.25" Wide 16WAK WINDOW, POWER (2) in Left and Right Doors 16WJG CAB DOOR LOCKS Power 16WKB AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster 16WKR WINDSHIELD Single Piece 16WLD CAB REAR SUSPENSION {Link Z9079D1} Dual Frame Mounted Cab Rear Air Suspension; Includes Special Crossmember Assembly 16XWD SUNSHADE, EXTERIOR Aerodynamic, Painted Roof Color; Includes Integral Clearance/Marker Lights 27DMA WHEELS, FRONT DISC; 22.5" Painted Steel, 2 Hand Hole, 10 Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs Includes : PAINT IDENTITY, FRONT WHEELS White Code Description

Page 32: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

28DMA WHEELS, REAR DUAL DISC; 22.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs Includes : PAINT IDENTITY, REAR WHEELS White 7372135415 (2) TIRE, FRONT 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply 7372135415 (8) TIRE, REAR 11R22.5 HSR2 (CONTINENTAL) 498 rev/mile, load range G, 14 ply ENGINE, DIESEL (0012KXL) ATTACHMENTS: 0016HBA (GAUGE CLUSTER) 0015LKU (FUEL/WATER SEPARATOR) 0012WEG (COLD STARTING EQUIPMENT) 0012THT (FAN DRIVE) Parameter Value UOM Max Accelerator Vehicle Speed:7902 80 MPH Vehicle Speed Limiter Override:7911 0, DISABLE FEATURE OR FUNCTION N/A VSLO Speed Increment:7912 10 MPH VSLO Maximum Activation Time:7914 30 MIN VSLO Time Interval to Reset:7915 8.0 HOURS VSLO Time Duration Source:7934 1, INTERVAL BASED ON REAL TIME CLOCK N/A Progressive Shift Enable:7744 0, DISABLE FEATURE OR FUNCTION N/A Low Gear Ratio Break Point:7742 5.825000 N/A High Gear Ratio Break Point:7743 1.643500000 N/A Low Gear Engine Speed Limit:7738 1550.0 RPM High Gear Engine Speed Limit:7739 1600.0 RPM Low Gear Engine Speed Range:7740 200.0 RPM High Gear Engine Speed Range:7741 200.0 RPM Min Gear Ratio for ProShift:7755 0.50 N/A Gear Down Protection Enable:7714 0, DISABLE FEATURE OR FUNCTION N/A Top Gr Minus 2 Light Ld VS Lim:7715 32 MPH Top Gr Minus 1 Light Ld VS Lim:7716 44 MPH Top Gr Minus 2 Heavy Ld VS Lim:7735 35 MPH Top Gr Minus 1 Heavy Ld VS Lim:7736 49 MPH Driver Reward Enable:7918 0, DISABLE FEATURE OR FUNCTION N/A Driver Reward Mode:7930 2, BOTH ACCELERATOR AND CRUISE VEHICLE SPEED LIMIT INCREASE N/A Driver Reward Performance Crit:7925 0, FUEL ECONOMY BASED REWARD SYSEM N/A Fuel Economy - Expected Level:7921 6.00 MPG Fuel Economy - Good Level:7920 6.25 MPG Fuel Economy - Excellent Level:7919 6.40 MPG % Idle Time - Expected Level:7924 25 % % Idle Time - Good Level:7923 18 % % Idle Time - Excellent Level:7922 10 % Driver Reward Ambient Temp H:7938 150.0 C Driver Reward Ambient Temp L:7939 -40.0 C VS Lim Increase - Expected Lvl:7926 0 MPH VS Lim Increase - Good Lvl:7927 2 MPH VS Lim Increase - Excel Lvl:7928 4 MPH VS Lim Decrease - Penalty Lvl:7929 -2 MPH Idle Engine Speed:8202 600.0 RPM Idle Speed Adjustment Enable:8215 1, ENABLE FEATURE OR FUNCTION N/A Idle Spd Adjust - Max Eng Spd:8212 0.0 RPM Idle Spd Adjust - Bump Step:8216 5.0 RPM Idle Spd Adjust Ramp Rate:8211 25 RPM/SEC Maximum Standstill Eng Speed:7753 2100.0 RPM Idle Shutdown Mode:7400 0, DISABLE FEATURE OR FUNCTION N/A ISD Time w/Park Brk Released:7401 15.0 MIN ISD Time w/Park Brake Set:7404 5.0 MIN ISD Latched Driver Override En:7407 0, DISABLE FEATURE OR FUNCTION N/A ISD Ambient Temp Override En:7408 0, DISABLE FEATURE OR FUNCTION N/A ISD Int Amb Temp Enable:7405 0, DISABLE FEATURE OR FUNCTION N/A ISD Max Ambient Temp Override:7402 20.0 C ISD Int Amb Temp Override:7406 15.0 C ISD Min Ambient Temp Override:7403 5.0 C ISD Max Engine Coolant Temp:7412 150.0 C ISD Min Engine Coolant Temp:7413 16.0 C ISD Idle Shutdown Max Eng Trq:7409 80 % Cruise Control Enable:7600 1, ENABLE FEATURE OR FUNCTION N/A CC Max Vehicle Speed:7604 80 MPH CC Min Vehicle Speed:7603 25.0000 MPH AESC Control:7500 0, DISABLE FEATURE OR FUNCTION N/A AESC In-cab Mode:7502 2, VARIABLE ENGINE SPEED CONTROL SELECTED N/A

Page 33: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

AESC Min Engine Speed:7522 600.0 RPM AESC Max Engine Speed:7508 1500.0 RPM AESC Preset Engine Speed 1:7505 800.0 RPM AESC Preset Engine Speed 2:7506 900.0 RPM AESC Preset Engine Speed 3:7514 1000.0 RPM AESC Preset Engine Speed 4:7515 1100.0 RPM AESC Preset Engine Speed 5:7516 1200.0 RPM AESC Preset Engine Speed 6:7517 1300.0 RPM AESC Activate at Preset Speed:7528 0, NO PRESET PRESELECTION N/A AESC Ramp Up Rate:7507 100.00 RPM/SEC AESC Ramp Down Rate:7524 100.00 RPM/SEC AESC Bump Up/Down Step:7525 25.0 RPM AESC In-cab Operator Interface:7503 0, NO (OFF) OR DISABLE N/A AESC Disable w/ Clutch Pedal:7510 1, ENABLE FEATURE OR FUNCTION N/A AESC Disable w/ Brake Pedal:7511 1, ENABLE FEATURE OR FUNCTION N/A AESC Accel Pedal Mode:7513 1, AESC OVERRIDDEN BY ACCELERATOR PEDAL N/A AESC Max Engine Load:7519 100.0000 % AESC Control to Engine Load:7530 0, KICK OUT OF AESC ABOVE PROGRAMMED LIMIT N/A AESC Max Engine Load Time:7527 8 SEC AESC Vehicle Speed Limit:7521 5.0000 MPH AESC Max Mobile Veh Spd:7501 5 MPH AESC Eng Spd Limit w/VSS Fault:7518 1500 RPM AESC Force Fan On:9007 0, DISABLE FEATURE OR FUNCTION N/A AESC Park Brake Override:7534 1, ENABLE FEATURE OR FUNCTION N/A AESC Transfer Case Signal Mode:8910 0, DRIVELINE N/A AESC Splitshaft Veh SPD Dsply:9307 0, SPEED SENSOR LOCATED IN WHEEL RIM N/A AESC Remote Accel Pedal Enable:7504 0, DISABLE FEATURE OR FUNCTION N/A AESC Remote Accel Pedal Switch:8914 0, DISABLE FEATURE OR FUNCTION N/A AESC Accel Max Eng Spd Ovrd:7520 1900.0 RPM Rem Accelerator Switch Input:9929 1, SAE J1939 MULTIPLEXED N/A Preset Remote AESC Input Type:9932 0, DISCRETE (HARDWIRED) INPUT N/A Variable Remote AESC Input:9933 0, DISCRETE (HARDWIRED) INPUT N/A Rem Accelerator Position Input:9935 1, SAE J1939 MULTIPLEXED N/A Engine Protection Mode:7700 1, TWO WAY WARNING (OIL PRES, WATER TEMP) N/A Powertrain Protection Enable:7722 0, DISABLE FEATURE OR FUNCTION N/A Torque Limiting in Gear:7717 0, DISABLE FEATURE OR FUNCTION N/A Highest Gear of Low Range:7718 2 N/A Highest Gear Rat of Low Range:7745 6.00 N/A Highest Gear of Int. Range:7748 4 N/A Highest Gear Rat of Int. Range:7746 4.00 N/A Highest Gear of High Range:7749 6 N/A Highest Gear Rat of High Range:7747 2.00 N/A Max Torque in Low Gear Range:7713 1250.0000 LB-FT Max Torque in Int. Gear Range:7750 1250.0000 LB-FT Max Torque in High Gear Range:7751 1250.0000 LB-FT VSS Anti-Tamper Max Eng Speed:7901 1338.4 RPM Auxilllary Shutdown Input Type:9931 0, DISCRETE (HARDWIRED) INPUT N/A Veh Speed Sensor Antitampering:7905 0, DISABLE FEATURE OR FUNCTION N/A Veh Overspd Threshold Level 1:7723 85.000000 MPH Veh Overspd Threshold Level 2:7724 87.000000 MPH Service Interval Enable 0, DISABLE FEATURE OR FUNCTION N/A Fuel Used Service Interval:9501 0 GALLONS Engine Hour Service Interval:9502 0 HOURS Veh Distance Service Interval:9503 0 MILES Service Soon Percent to Notify:9507 90 % Customer Unit Number:6605 0 N/A Hard Braking Incident Counter:8904 1, ENABLE FEATURE OR FUNCTION N/A Hard Braking Decel Threshold:8905 7.40 MPH/SEC Vehicle Over-speed Indicator:7754 0, FEATURE OR FUNCTION IS DISABLED N/A Customer Password:8700 00000000 N/A These Electronic Parameters have been successfully finalized

Page 34: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

H-GAC Product Code: B6 CT680L – SFA – CF6AB, Conv. Cab, 124" BBC (CF6AB), Truck Configuration

Model Profile 2015 CT680L SFA 6x4 (CF6AB) APPLICATION: Construction Dump MISSION: Requested GVWR: 54000. Calc. GVWR: 52000 Calc. Start / Grade Ability: 0% / 0% @ 0 MPH Calc. Geared Speed: N/A FUEL ECONOMY: N/A DIMENSION: Wheelbase: 205.00, CA: 110.00, Axle to Frame: 53.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FR-14210B} 10-Speed Manual, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-12-143A} Wide Track, I-Beam Type, 12,000-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 4.11 CAB: Conventional TIRE, FRONT: (2) 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply TIRE, REAR: (8) 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KW Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description F/R Wt Tot Wt (lbs) (lbs) CF6AB00 Base Chassis, Model CT680L SFA 6x4 with 205.00 Wheelbase, 110.00 CA, and 53.00 Axle to Frame. 7630/8306 15936 1652 CROSSMEMBER, REAR Relocated to End of Frame -19/100 81 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 71/74 145 1LBH BUMPER, FRONT Black Painted Multi-piece Steel 0/0 0 1WWT WHEELBASE RANGE 169" (430cm) Through and Including 205" (520cm) 0/0 0 2ARW AXLE, FRONT NON-DRIVING {Meritor MFS-12-143A} Wide Track, I-Beam Type, 12,000-lb Capacity -58/0 -58 3ADC SUSPENSION, FRONT, SPRING Parabolic, Taper Leaf; 12,000-lb Capacity; With Shock Absorbers 0/0 0 4091 BRAKE SYSTEM, AIR Dual System for Straight Truck Applications 0/0 0 Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : DUST SHIELDS, FRONT BRAKE : DUST SHIELDS, REAR BRAKE : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : INVERSION VALVE Bendix SR-1 and Double Check Valve : PARKING BRAKE CONTROL Yellow Knob, Located on Instrument Panel : PARKING BRAKE VALVE For Truck : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for 4x2, 2 for 6x4 : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic : SWITCH, AUXILIARY Interrupter for Cab Clearance/Marker Lights (Blinks Lights with Headlight Switch in "ON" Position); Instrument Panel Mounted Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4732 DRAIN VALVE {Berg} Manual; With Pull Chain, for Air Tank 0/0 0 Includes

Page 35: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

: DRAIN VALVE Mounted in Wet Tank 4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel) 0/0 0 4EBS AIR DRYER {Bendix AD-9} With Heater 0/0 0 Includes : AIR DRYER LOCATION Inside Left Rail, Back of Cab 4ESX BRAKE CHAMBERS, FRONT AXLE {Haldex} 20 SqIn 0/0 0 4EVL BRAKE CHAMBERS, REAR AXLE {Haldex GC3030LHDHO} 30/30 Spring Brake 0/0 0 4JCJ BRAKES, FRONT, AIR CAM S-Cam; 16.5" x 5.0"; Includes 20 Sq. In. Long Stroke Brake Chambers 0/0 0 Code Description F/R Wt Tot Wt (lbs) (lbs) 4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.In. Long Stroke Brake Chamber and Spring Actuated Parking Brake 0/0 0 4SPM AIR COMPRESSOR {Bendix BA-921 Head Unload} 15.9 CFM Capacity, Single Cylinder 0/0 0 5710 STEERING COLUMN Tilting and Telescoping 0/0 0 5PSA STEERING GEAR {Sheppard M-100} Power 0/0 0 5WBH STEERING WHEEL {Caterpillar} 2-Spoke, 18" Diam., Dark Neutral, Leather Wrapped 0/0 0 7BJU EXHAUST SYSTEM Switchback Horizontal Aftertreatment Device, Frame Mounted Right Side Under Cab; Includes Single Vertical Tail Pipe & Guard, Right Side, Cab Mounted 0/0 0 8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment 0/0 0 Includes : BATTERY BOX Aluminum : CIGAR LIGHTER Includes Ash Cup, Center Console Mounted : FUSES, ELECTRICAL SAE Blade-Type : HAZARD SWITCH Integral with Turn Signal Switch : HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever : HEADLIGHTS (2) Composite with Halogen Projector Beam : HORN, AIR Single, Chrome : HORN, ELECTRIC Single : PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light : READING LIGHT, CAB (2) with Individual Switches; One Above Each Door : STARTER SWITCH Electric, Key Operated : STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector : TURN SIGNAL FLASHER : TURN SIGNAL SWITCH Manual Cancelling with Lane Change Feature : TURN SIGNALS, FRONT Includes Integral Reflectors and Side Marker Lights; Fender Mounted : WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature, Steering Column Mounted : WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted : WIRING, CHASSIS Color Coded and Continuously Numbered 8653 HORN, AIR Single, Located Under Cab 4/1 5 8718 POWER SOURCE Cigar Type Receptacle without Plug and Cord 0/0 0 8GGN ALTERNATOR {Bosch LH160} Brush Type, 12 Volt 160 Amp. Capacity, Pad Mount 0/0 0 8MMJ BATTERY SYSTEM {Caterpillar} (3) 12 Volt 2130CCA Total 0/0 0 8RBN RADIO Omit Item; With Wiring and Antenna, Includes Multiple Speakers 0/0 0 Includes : SPEAKERS IN CAB (4) Coaxial 8RMG ANTENNA BASE (2) Single Function, (1) for CB and (1) for Entertainment Radio, Without Splitter, Separate Lead-Ins, With CB Antenna Mounted on Left Mirror and AM/FM Antenna Mounted on Right Mirror 0/0 0 8VUK BATTERY BOX Aluminum With Plastic Cover, 18" Wide, 2, 3, or 4 Battery Capacity, Mounted Right Side Back of Cab 0/0 0 8WCK POWER SOURCE, TERMINAL TYPE 2-Post 0/0 0 Code Description F/R Wt Tot Wt (lbs) (lbs) 8WNH RUNNING LIGHT (2) Daytime 0/0 0

Page 36: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

8WXG STARTING MOTOR {Mitsubishi Electric Automotive America 105P} 12-Volt, with Soft-Start 0/0 0 9107 FRONT END Tilting, Fiberglass 0/0 0 9HAN INSULATION, UNDER HOOD for Sound Abatement 0/0 0 9HBN INSULATION, SPLASH PANELS for Sound Abatement 0/0 0 10060 PAINT SCHEMATIC, PT-1 Single Color, Design 100 0/0 0 10761 PAINT TYPE Base Coat/Clear Coat, 1-2 Tone 0/0 0 10769 PAINT CLASS Premium Color 0/0 0 11MGZ CLUTCH {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity 0/0 0 Includes : CLUTCH RELEASE BEARING Greasable 12KXP ENGINE, DIESEL {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) 0/0 0 12THT FAN DRIVE {Horton Drivemaster} Direct Drive Type, Two Speed With Residual Torque Device for Disengaged Fan Speed 0/0 0 12UCX RADIATOR Aluminum; 3-Row, Front to Back Cross Flow System, 1430 SqIn, 560 SqIn CAC, 1110 SqIn 3 Core LTR 0/0 0 12UNJ FEDERAL EMISSIONS EPA, OBD and GHG Certified for Calendar Year 2014; CT13 Engines 0/0 0 12VBT AIR CLEANER Single Element, Heavy Duty 0/0 0 12WCX HOSE CLAMPS, RADIATOR HOSES {Gates} Shrink Band Type 0/0 0 12WEG COLD STARTING EQUIPMENT Automatic; With Engine ECM Control 0/0 0 12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, Engine Mounted 0/0 0 12WZB EMISSION COMPLIANCE Low NOx Idle Engine, Complies with California Clean Air Regulations; Includes "Certified Clean Idle" Decal on Hood 0/0 0 13GHJ TRANSMISSION, MANUAL {Fuller FR-14210B} 10-Speed Manual, With Air Shift 0/0 0 Includes : CLUTCH BRAKE Torque Limiting : FILL PLUG, MAGNETIC 13WLB TRANSMISSION OIL {EmGard 50W} Synthetic; 22 thru 33.99 Pints 0/0 0 14GVU AXLE, REAR, TANDEM {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Lube Oil Pump . Gear Ratio: 4.11 0/0 0 Includes : POWER DIVIDER LOCK Air Operated, Cab Control with Indicator Light in Cluster : REAR AXLE DRAIN PLUG (2) Magnetic, For Tandem Rear Axle Code Description F/R Wt Tot Wt (lbs) (lbs) 14ULX SUSPENSION, REAR, TANDEM {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers 0/0 0 Includes : CROSSMEMBER, SUSPENSION Stamped Steel Double Dogbone Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 14WAL SUSPENSION/REAR-AXLE IDENTITY for Meritor Tandem Rear Axles With Bar- Pin Beam Attachment Type Suspensions 0/0 0 14WLD AXLE, REAR, LUBE {EmGard 75W-90} Synthetic Oil; 50 thru 64.99 Pints 0/0 0 15DYP DEF TANK 9.5 U.S. Gal. 36.0L Capacity, Frame Mounted Outside Left Rail, Under Cab 0/0 0 15LKU FUEL/WATER SEPARATOR {Racor} Fuel Pre-Filter and Filter Base, Includes Water-In-Fuel Sensor

Page 37: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

0/0 0 15SGL FUEL TANK Non-Polished Aluminum, 24" Diam., 80 U.S. Gal., 302 L Capacity Mounted Left Side Under Cab 0/0 0 16031 CAB Conventional 0/0 0 Includes : COAT HOOK, CAB Located on Rear Wall, Behind Passenger Seat : CONSOLE, CENTER Plastic, Driver Convenience with a Cup and Change Holder, Ash Tray and Lower Storage Area : DOME LIGHT, CAB (2) Driver and Passenger Dome Lights with Individual Switches, in Headliner : DOOR CHECK STRAP (2) One Each Door : GLASS, ALL WINDOWS Tinted : GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side : GRAB HANDLE, EXTERIOR (2) Mounted Behind Driver and Passenger Doors : INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color : SKIN Riveted : STEP (4) Two Steps Per Door 16400 SEAT, PASSENGER Omit Item 0/0 0 16HBA GAUGE CLUSTER English With English Electronic Speedometer 0/0 0 16JPC SEAT, DRIVER {National 2000 Model 295} Air Suspension, Intermediate Back, All Vinyl, 2 Arm Rests, Isolator, 7" Adjuster, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, 3 Position Rear Cushion, 2-15 Degree Back Angle Adjust, Vinyl Suspension Cover 0/0 0 16SKS MIRRORS (2) {Lang Mekra} Aero; Rectangular, 7.09" x 15.75" & Integral Convex Both Sides, 102" Inside Spacing, Breakaway Type, Heated Heads Thermostat Controlled, Amber Lens Clearance Light LED, Black Painted Finish Heads, Brackets & Arms 0/0 0 16VRT HEATER, ENHANCED CIRCULATION {Bergstrom} Control, for Extreme Cold Weather Climates 0/0 0 16VTH CAB INTERIOR TRIM Premium Level; for Caterpillar, Day Cab 0/0 0 Includes Code Description F/R Wt Tot Wt (lbs) (lbs) : "A" PILLAR COVER Molded Plastic : CAB INTERIOR TRIM PANELS Vinyl : CONSOLE, OVERHEAD Molded Plastic with Three Storage Pockets; One with Strap for CB Radio Mounting; Two with Netting, Courtesy Lights with Switches : COURTESY LIGHT (2) Driver and Passenger Door Mounted : DOOR TRIM PANELS Vinyl Upper with Power Locks and Windows, Upper and Lower Grab Handles, Both Sides : FLOOR COVERING Rubber, Black : HEADLINER Soft Padded Vinyl : HEATER BOX Metal, Painted Black : INSTRUMENT PANEL TRIM Vinyl : MIRROR, CONVEX, LOOK DOWN Black Finish; 6" x 10-1/4"; Located on Passenger Side : STORAGE POCKET, DOOR (2) Driver and Passenger Door : SUN VISOR (2) Vinyl with Molded Toll Ticket Retainer 16VZA WINDOW, REAR 52.25" Wide 0/0 0 16WAK WINDOW, POWER (2) in Left and Right Doors 0/0 0 16WJG CAB DOOR LOCKS Power 0/0 0 16WKB AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster 0/0 0 16WKR WINDSHIELD Single Piece 0/0 0 16WLD CAB REAR SUSPENSION {Link Z9079D1} Dual Frame Mounted Cab Rear Air Suspension; Includes Special Crossmember Assembly 0/0 0 16XWD SUNSHADE, EXTERIOR Aerodynamic, Painted Roof Color; Includes Integral Clearance/Marker Lights 0/0 0 27DMH WHEELS, FRONT DISC; 24.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs 34/0 34 Includes : PAINT IDENTITY, FRONT WHEELS White

Page 38: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

28DML WHEELS, REAR DUAL DISC; 24.5" Painted Steel, 2-Hand Hold, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Aluminum Hubs 0/84 84 7384225423 (2) TIRE, FRONT 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply 50/0 50 7384225423 (8) TIRE, REAR 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply 0/200 200 Total Component Weight: 7712/8765 16477

Page 39: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

H-GAC Product Code: B7 CT680L – SFA – CF6AB, Conv. Cab, 124" BBC (CF6AB), Tractor Configuration

. Model Profile 2015 CT680L SFA 6x4 (CF6AB) APPLICATION: Bottom Dump MISSION: Requested GCWR: 80000. Calc. GVWR: 53200 Calc. Start / Grade Ability: 0% / 0% @ 0 MPH Calc. Geared Speed: 0 MPH FUEL ECONOMY: N/A DIMENSION: Wheelbase: 207.00, CA: 112.00, Axle to Frame: 57.00 ENGINE, DIESEL: {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller FR-14210B} 10-Speed Manual, With Air Shift CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000- lb Capacity, R Wheel Ends, With Lube Oil Pump Gear Ratio: 4.11 CAB: Conventional TIRE, FRONT: (2) 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply TIRE, REAR: (8) 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers PAINT: Cab schematic 100KW Location 1: 9221, Light Cameo White (Prem) Chassis schematic N/A Code Description F/R Wt Tot Wt (lbs) (lbs) CF6AB00 Base Chassis, Model CT680L SFA 6x4 with 207.00 Wheelbase, 112.00 CA, and 57.00 Axle to Frame. 7630/8306 15936 1616 FRAME RAILS WITH TAPERED REAR -7/41 34 1CDH FRAME RAILS Heat Treated Alloy Steel (120,000 PSI Yield); 12.250" x 3.380" x 0.375" (304.8mm x 85.6mm x 9.5mm); 543.0" (13793mm) Maximum OAL 70/97 167 1LBH BUMPER, FRONT Black Painted Multi-piece Steel 0/0 0 1WWU WHEELBASE RANGE 207" (525cm) Through and Including 260" (660cm) 0/0 0 2ASG AXLE, FRONT NON-DRIVING {Meritor MFS-13-143A} Wide Track, I-Beam Type, 13,200-lb Capacity 0/0 0 3ADD SUSPENSION, FRONT, SPRING Parabolic, Taper Leaf; 14,000-lb Capacity; With Shock Absorbers -185/-4 -189 4092 BRAKE SYSTEM, AIR Dual System for Tractor Applications 5/-7 -2 Includes : BRAKE LINES Color and Size Coded Nylon : DRAIN VALVE Twist-Type : GAUGE, AIR PRESSURE (2) Air 1 and Air 2 Gauges; Located in Instrument Cluster : GLAD HANDS (2) One for Service and One for Emergency; Trailer Hoses from Cab : HAND CONTROL VALVE, AIR Mounted on Steering Column : HOSE TENDER Back of Cab Mounted : PARKING BRAKE CONTROL Yellow and Red Knobs, Located on Instrument Panel : PARKING BRAKE VALVE Combination Valve for Tractor and Trailer : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 for Forward Rear Axle : SLACK ADJUSTERS, FRONT Automatic : SLACK ADJUSTERS, REAR Automatic : SWITCH, AUXILIARY Interrupter for Cab and Trailer Clearance/Marker Lights (Blinks Lights with Headlight Switch in "ON" Position); Instrument Panel Mounted : TRACTOR PROTECTION VALVE : TRAILER HOSES AND CABLES 15' Coiled Lighting Cable with 7-Way Connector and with 15' Coiled Nylon Brake Hose Notes : The following features should be considered when calculating Rear GAWR: Rear

Page 40: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 4193 BRAKES, FRONT, AIR CAM 16.5" x 6", Includes 24 SqIn Long Stroke Brake Chambers 114/0 114 4732 DRAIN VALVE {Berg} Manual; With Pull Chain, for Air Tank 0/0 0 Includes : DRAIN VALVE Mounted in Wet Tank 4AAB BRAKE CHAMBERS, ADDITIONAL (2) {Haldex} Spring Brake Type; 30/30 SqIn 0/44 44 Includes : QUICK RELEASE VALVE Bendix On Rear Axle for Spring Brake Release: 1 Additional for Rear Rear Axle Code Description F/R Wt Tot Wt (lbs) (lbs) 4AZA AIR BRAKE ABS {Bendix AntiLock Brake System} Full Vehicle Wheel Control System (4-Channel) 0/0 0 4EBS AIR DRYER {Bendix AD-9} With Heater 0/0 0 Includes : AIR DRYER LOCATION Inside Left Rail, Back of Cab 4ETE BRAKE CHAMBERS, FRONT AXLE {Haldex} 24 SqIn 0/0 0 4EVL BRAKE CHAMBERS, REAR AXLE {Haldex GC3030LHDHO} 30/30 Spring Brake 0/0 0 4NDB BRAKES, REAR, AIR CAM S-Cam; 16.5" x 7.0"; Includes 30/30 Sq.In. Long Stroke Brake Chamber and Spring Actuated Parking Brake 0/0 0 4SPM AIR COMPRESSOR {Bendix BA-921 Head Unload} 15.9 CFM Capacity, Single Cylinder 0/0 0 4WCC BRAKE PACKAGE, FRONT {Dana Spicer ES-165-6} Air, Cam Type, Extended Service; Size 16.5" x 6", Includes Automatic Slack Adjusters 0/0 0 4WCD BRAKE PACKAGE, REAR {Dana Spicer ES-165-7} Air, Cam Type, Extended Service; Size 16.5" x 7", Includes Automatic Slack Adjusters 0/0 0 5710 STEERING COLUMN Tilting and Telescoping 0/0 0 5PSA STEERING GEAR {Sheppard M-100} Power 0/0 0 5WBH STEERING WHEEL {Caterpillar} 2-Spoke, 18" Diam., Dark Neutral, Leather Wrapped 0/0 0 7BJU EXHAUST SYSTEM Switchback Horizontal Aftertreatment Device, Frame Mounted Right Side Under Cab; Includes Single Vertical Tail Pipe & Guard, Right Side, Cab Mounted 0/0 0 8000 ELECTRICAL SYSTEM 12-Volt, Standard Equipment 0/0 0 Includes : BATTERY BOX Aluminum : CIGAR LIGHTER Includes Ash Cup, Center Console Mounted : FUSES, ELECTRICAL SAE Blade-Type : HAZARD SWITCH Integral with Turn Signal Switch : HEADLIGHT DIMMER SWITCH Integral with Turn Signal Lever : HEADLIGHTS (2) Composite with Halogen Projector Beam : HORN, AIR Single, Chrome : HORN, ELECTRIC Single : PARKING LIGHT Integral with Front Turn Signal and Rear Tail Light : READING LIGHT, CAB (2) with Individual Switches; One Above Each Door : STARTER SWITCH Electric, Key Operated : STOP, TURN, TAIL & B/U LIGHTS Dual, Rear, Combination with Reflector : TURN SIGNAL FLASHER : TURN SIGNAL SWITCH Manual Cancelling with Lane Change Feature : TURN SIGNALS, FRONT Includes Integral Reflectors and Side Marker Lights; Fender Mounted : WINDSHIELD WIPER SWITCH 2-Speed with Wash and Intermittent Feature, Steering Column Mounted : WINDSHIELD WIPERS Single Motor, Electric, Cowl Mounted : WIRING, CHASSIS Color Coded and Continuously Numbered 8653 HORN, AIR Single, Located Under Cab 4/1 5 8718 POWER SOURCE Cigar Type Receptacle without Plug and Cord 0/0 0 Code Description F/R Wt Tot Wt (lbs) (lbs)

Page 41: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

8GGN ALTERNATOR {Bosch LH160} Brush Type, 12 Volt 160 Amp. Capacity, Pad Mount 0/0 0 8MMJ BATTERY SYSTEM {Caterpillar} (3) 12 Volt 2130CCA Total 0/0 0 8RBN RADIO Omit Item; With Wiring and Antenna, Includes Multiple Speakers 0/0 0 Includes : SPEAKERS IN CAB (4) Coaxial 8RMG ANTENNA BASE (2) Single Function, (1) for CB and (1) for Entertainment Radio, Without Splitter, Separate Lead-Ins, With CB Antenna Mounted on Left Mirror and AM/FM Antenna Mounted on Right Mirror 0/0 0 8VUK BATTERY BOX Aluminum With Plastic Cover, 18" Wide, 2, 3, or 4 Battery Capacity, Mounted Right Side Back of Cab 0/0 0 8WCK POWER SOURCE, TERMINAL TYPE 2-Post 0/0 0 8WNH RUNNING LIGHT (2) Daytime 0/0 0 8WXG STARTING MOTOR {Mitsubishi Electric Automotive America 105P} 12-Volt, with Soft-Start 0/0 0 9107 FRONT END Tilting, Fiberglass 0/0 0 9HAN INSULATION, UNDER HOOD for Sound Abatement 0/0 0 9HBN INSULATION, SPLASH PANELS for Sound Abatement 0/0 0 10060 PAINT SCHEMATIC, PT-1 Single Color, Design 100 0/0 0 10761 PAINT TYPE Base Coat/Clear Coat, 1-2 Tone 0/0 0 10769 PAINT CLASS Premium Color 0/0 0 10HHW FIFTH WHEEL, AIR SLIDE {Fontaine SL7LWB675012} 12" Slide, Cast Top Plate, 6.75" Above Top of Frame, Left Hand Release 4/434 438 10WLX MUD FLAPS, REAR Black Rubber, Anti-Sail "CAT" Silver Logo; Less Holders -4/19 15 10WPR MUD FLAP HOLDER Spring Loaded, Painted Black; With Red and White Reflective Tape; Less Flaps -14/65 51 11MGZ CLUTCH {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity 0/0 0 Includes : CLUTCH RELEASE BEARING Greasable 12KXP ENGINE, DIESEL {CT 13} EPA 10, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) 0/0 0 12THT FAN DRIVE {Horton Drivemaster} Direct Drive Type, Two Speed With Residual Torque Device for Disengaged Fan Speed 0/0 0 12UCX RADIATOR Aluminum; 3-Row, Front to Back Cross Flow System, 1430 SqIn, 560 SqIn CAC, 1110 SqIn 3 Core LTR 0/0 0 12UNJ FEDERAL EMISSIONS EPA, OBD and GHG Certified for Calendar Year 2014; CT13 Engines 0/0 0 12VBT AIR CLEANER Single Element, Heavy Duty 0/0 0 12WCX HOSE CLAMPS, RADIATOR HOSES {Gates} Shrink Band Type 0/0 0 Code Description F/R Wt Tot Wt (lbs) (lbs) 12WEG COLD STARTING EQUIPMENT Automatic; With Engine ECM Control 0/0 0 12WTA FAN DRIVE SPECIAL EFFECTS Fan Cooling Ring with Fan Shroud Effects, Engine Mounted 0/0 0 12WZB EMISSION COMPLIANCE Low NOx Idle Engine, Complies with California Clean Air Regulations; Includes "Certified Clean Idle" Decal on Hood 0/0 0 13GHJ TRANSMISSION, MANUAL {Fuller FR-14210B} 10-Speed Manual, With Air Shift 0/0 0 Includes : CLUTCH BRAKE Torque Limiting : FILL PLUG, MAGNETIC 13WLB TRANSMISSION OIL {EmGard 50W} Synthetic; 22 thru 33.99 Pints 0/0 0 14GVU AXLE, REAR, TANDEM {Meritor MT-40-14X-4DFR-P} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Lube Oil Pump . Gear Ratio: 4.11 0/0 0 Includes

Page 42: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

: POWER DIVIDER LOCK Air Operated, Cab Control with Indicator Light in Cluster : REAR AXLE DRAIN PLUG (2) Magnetic, For Tandem Rear Axle 14ULX SUSPENSION, REAR, TANDEM {Hendrickson HMX-400-54} Walking Beam Type 54" Axle Spacing; 40,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers 0/0 0 Includes : CROSSMEMBER, SUSPENSION Stamped Steel Double Dogbone Notes : The following features should be considered when calculating Rear GAWR: Rear Axles; Rear Suspension; Brake System; Brakes, Rear Air Cam; Brake Shoes, Rear; Special Rating, GAWR; Wheels; Tires. 14WAL SUSPENSION/REAR-AXLE IDENTITY for Meritor Tandem Rear Axles With Bar- Pin Beam Attachment Type Suspensions 0/0 0 14WBV SHOCK ABSORBERS, REAR (4) for Hendrickson HMX Suspension Only, Mounted from Frame to Beam 0/31 31 14WLD AXLE, REAR, LUBE {EmGard 75W-90} Synthetic Oil; 50 thru 64.99 Pints 0/0 0 15DYP DEF TANK 9.5 U.S. Gal. 36.0L Capacity, Frame Mounted Outside Left Rail, Under Cab 0/0 0 15LKU FUEL/WATER SEPARATOR {Racor} Fuel Pre-Filter and Filter Base, Includes Water-In-Fuel Sensor 0/0 0 15SGL FUEL TANK Non-Polished Aluminum, 24" Diam., 80 U.S. Gal., 302 L Capacity Mounted Left Side Under Cab 0/0 0 16031 CAB Conventional 0/0 0 Includes : COAT HOOK, CAB Located on Rear Wall, Behind Passenger Seat : CONSOLE, CENTER Plastic, Driver Convenience with a Cup and Change Holder, Ash Tray and Lower Storage Area : DOME LIGHT, CAB (2) Driver and Passenger Dome Lights with Individual Switches, in Headliner : DOOR CHECK STRAP (2) One Each Door : GLASS, ALL WINDOWS Tinted Code Description F/R Wt Tot Wt (lbs) (lbs) : GRAB HANDLE, CAB INTERIOR (1) "A" Pillar Mounted, Passenger Side : GRAB HANDLE, EXTERIOR (2) Mounted Behind Driver and Passenger Doors : INTERIOR SHEET METAL Upper Door (Above Window Ledge) Painted Exterior Color : SKIN Riveted : STEP (4) Two Steps Per Door 16400 SEAT, PASSENGER Omit Item 0/0 0 16HBA GAUGE CLUSTER English With English Electronic Speedometer 0/0 0 16JPC SEAT, DRIVER {National 2000 Model 295} Air Suspension, Intermediate Back, All Vinyl, 2 Arm Rests, Isolator, 7" Adjuster, 1 Chamber Lumbar, 2 Position Front Cushion Adjust, 3 Position Rear Cushion, 2-15 Degree Back Angle Adjust, Vinyl Suspension Cover 0/0 0 16SKS MIRRORS (2) {Lang Mekra} Aero; Rectangular, 7.09" x 15.75" & Integral Convex Both Sides, 102" Inside Spacing, Breakaway Type, Heated Heads Thermostat Controlled, Amber Lens Clearance Light LED, Black Painted Finish Heads, Brackets & Arms 0/0 0 16VRT HEATER, ENHANCED CIRCULATION {Bergstrom} Control, for Extreme Cold Weather Climates 0/0 0 16VTH CAB INTERIOR TRIM Premium Level; for Caterpillar, Day Cab 0/0 0 Includes : "A" PILLAR COVER Molded Plastic : CAB INTERIOR TRIM PANELS Vinyl : CONSOLE, OVERHEAD Molded Plastic with Three Storage Pockets; One with Strap for CB Radio Mounting; Two with Netting, Courtesy Lights with Switches : COURTESY LIGHT (2) Driver and Passenger Door Mounted : DOOR TRIM PANELS Vinyl Upper with Power Locks and Windows, Upper and Lower Grab Handles, Both Sides

Page 43: Caterpillar Standard Features Bid Invitation #HT06-14...Caterpillar Standard Features Bid Invitation #HT06-14 The following descriptions are the standard features, as pulled from the

: FLOOR COVERING Rubber, Black : HEADLINER Soft Padded Vinyl : HEATER BOX Metal, Painted Black : INSTRUMENT PANEL TRIM Vinyl : MIRROR, CONVEX, LOOK DOWN Black Finish; 6" x 10-1/4"; Located on Passenger Side : STORAGE POCKET, DOOR (2) Driver and Passenger Door : SUN VISOR (2) Vinyl with Molded Toll Ticket Retainer 16VZA WINDOW, REAR 52.25" Wide 0/0 0 16WAK WINDOW, POWER (2) in Left and Right Doors 0/0 0 16WJG CAB DOOR LOCKS Power 0/0 0 16WKB AIR CONDITIONER {International Blend-Air} With Integral Heater & Defroster 0/0 0 16WKR WINDSHIELD Single Piece 0/0 0 16WLD CAB REAR SUSPENSION {Link Z9079D1} Dual Frame Mounted Cab Rear Air Suspension; Includes Special Crossmember Assembly 0/0 0 16XWD SUNSHADE, EXTERIOR Aerodynamic, Painted Roof Color; Includes Integral Clearance/Marker Lights 0/0 0 27DMH WHEELS, FRONT DISC; 24.5" Painted Steel, 2 Hand Hole, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Steel Hubs 34/0 34 Includes Code Description F/R Wt Tot Wt (lbs) (lbs) : PAINT IDENTITY, FRONT WHEELS White 28DML WHEELS, REAR DUAL DISC; 24.5" Painted Steel, 2-Hand Hold, 10-Stud (285.75MM BC) Hub Piloted, Flanged Nut, Metric Mount, 8.25 DC Rims; With Aluminum Hubs 0/84 84 7384225423 (2) TIRE, FRONT 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply 50/0 50 7384225423 (8) TIRE, REAR 11R24.5 HDR2 (CONTINENTAL) 468 rev/mile, load range H, 16 ply 0/200 200 810000 FIFTH WHEEL LOCATION On Rear Axle Centerline 0/0 0 Total Component Weight: 7701/9311 17012