Catnic Brochure

Catnic

October 2007

International Product Catalogue

ISO 9001

Quality Building Products

Catnic is a leading supplier and manufacturer of building products for the

construction industry. Acknowledged for our excellence of service and conformance

to the highest quality standards, our products have been installed successfully in

municipal buildings and domestic properties in over 30 countries worldwide.

Building on our strength in the steel lintels market, Catnic also supply a

comprehensive range of branded building components and plasterers’ profiles which

are manufactured to the same industry-leading high standards as our renowned

steel lintels. Selecting the Catnic brand assures that the products you have chosen

are of superior quality and are fully supported by our extensive distributor network.

If you need details of your local distributor,

or if you require any further information please contact.

International Sales Dept.

Catnic – Corus (UK) Ltd

Pontypandy Estate

Caerphilly

United Kingdom

CF83 3GL

Tel +44 (0) 29 2033 7900

Fax +44 (0) 29 2088 0855

Website: www.catnic.com

2 Catnic International

Contents

L I N T E L S

Steel Lintels 4

P L A S T E R A C C E S S O R I E S

Installation guide 12

Beads

Galvanised 14

Stainless Steel 23

PVC nosed 27

PVC 29

Expanded metal

Lath and Riblath 30

Arch formers 32

Coil Mesh for Blockwork 34

W A L L A C C E S S O R I E S

Wall Ties 36

Wall Connectors 37

Brick and Block spacer system 38

F E N C E P O S T S Y S T E M S

QwikPost 41

Catnic International 3

Design Features

Features & Benefits

Catnic Steel Lintels provide a combination of strength and light weight resulting

in efficient loadbearing performance and increased productivity on site

> No need for lifting equipment as two men can lift even the longest length

into position.

> No delay to blockwork, it can be continued immediately.

> No propping required while waiting for concrete to cure.

> Corrosion protected.

> Safe Working Loads are all given in the tables provided and have been

substantiated by independent testing.

> Efficient plaster key.

> Brackets for column fixing provide considerable time savings.

SpecificationsCorrosion Protection System

In addition to the use of high quality galvanised steel, the lintels are further

protected against corrosion by the addition of a thermosetting polyester powder

coating. This coating is applied by an electrostatic process that ensures close

control over quality and thickness of coating.

This duplex system of an organic coating over galvanised steel provides excellent

long-term resistance to the corrosive elements present in all building situations.

NOTE:

Lintels type CN92 and CN102 are designed for internal use only and are supplied

without powder coating.

Lintels should be installed with a 20cm bearing at each end and should be fully

bedded on blockwork mortar. Our Technical Department should be consulted if

bearings less than 20cm are required.


Quality Assurance

Catnic steel lintels are made to the highest quality standards.

> The steel used in their manufacture is in accordance with

BSEN 10327:2004-DX51D+Z275

> Lintels conform to the specifications laid down in BS 5977: Part 2: 1983.

> Catnic was the first lintel manufacturer to be awarded a kitemark symbol

and the range is identified with the symbol in this brochure.

BSI licences the use of the kitemark only after:

> It has independently tested the products and is satisfied that it conforms with

the BS specification.

> It has visited and assessed the manufacturer to ISO 9001 and is satisfied that

the quality control systems used ensure that the product continues to conform

to specifications.

Technical Advisory Service

A comprehensive scheduling service is offered without charge or obligation. Simply

send us a set of drawings (plans, sections and elevations) for any size project and

we will provide you with a comprehensive schedule of requirements.

In addition to the range shown in this catalogue many other sizes and types are

available upon request.

Installation

> Damaged lintels should not be used.

> 20cm end bearing should be allowed at each side.

> Lintels should not be cut down from manufactured lengths without prior

approval.

> If you have any doubt concerning any installation, please contact Catnic

for advice.

> For cavity lintels, the inner and outer leaves must be raised together.

Plaster Key

> Generally lintels are supplied with perforations as a plaster key but

occasionally it may be necessary to supply expanded mesh fixed to

the lintels as an alternative.

This brochure is copyright, the copyright being

owned by Catnic – Corus UK Limited and the

unauthorised reproduction of the whole or part of

it is prohibited.

© Catnic – Corus UK Limited 2007

ISO 9001


Catnic lintel installation

TOTAL Installation Time – 2 minutes

Concrete cast in-situ lintel installation

TOTAL Installation Time – 48 minutes. The concrete lintel must be left to cure before

continuing with blockwork installation.

1 Vertical framework erected and secured and a horizontal level taken.

2 Commencement of lintel framework.

3 Continuation of framework.

4 Completion of framework.

5 Completion of lintel after steel reinforcement and pouring of concrete.

6 Wait for concrete to set

1 2 3

In the time taken to install just one concrete lintel,

TWENTY FOUR Catnic lintels could have been

installed.

Comparison of installation times

of a Catnic lintel and a conventional

concrete cast in-situ lintel.

WAIT!



Channel Lintels for Solid Walls

Lintel Profiles – dimensions in mm.

CN100

50

103 CN103

75

103 CN150

50

153 CN152

75

153


CN200 CN250CN202

50

203

75

203

50

253

LINTEL TYPE/CODE CN100 CN103 CN150 CN152

Gauge Code A B C C A B C C

Sheet Thickness (mm) 2.0 2.5 3.1 3.1 2.0 2.5 3.1 3.1

Weight per metre (kg) 3.0 3.7 4.7 5.9 3.7 4.7 5.9 7.1

Safe working load uniformly distributed (tonnes)

Lengths available (m) 0.90 – 1.20 0.55 0.80 1.12 1.63 0.48 0.76 1.22 1.63

in increments of 0.1m 1.30 – 1.50 0.42 0.58 0.66 1.25 0.37 0.58 0.79 1.25

1.60 – 1.80 0.31 0.38 0.44 1.00 0.27 0.41 0.52 1.00

1.90 – 2.10 – 0.24 0.31 0.86 – 0.27 0.37 0.86

2.20 – 2.40 – 0.18 0.23 0.64 – 0.19 0.28 0.64

2.50 – 2.70 – – 0.16 0.47 – – 0.19 0.47

2.80 – 3.00 – – 0.13 0.38 – – 0.14 0.38

LINTEL TYPE/CODE CN200 CN202 CN250

Gauge Code A B C C A B C

Sheet Thickness (mm) 2.0 2.5 3.1 3.1 2.0 2.5 3.1

Weight per metre (kg) 4.4 5.6 7.1 8.5 5.4 6.7 8.6

Safe working load uniformly distributed (tonnes)

Lengths available (m) 0.90 – 1.20 0.62 0.77 1.05 1.63 0.62 0.77 1.05

in increments of 0.1m 1.30 – 1.50 0.48 0.59 0.80 1.25 0.48 0.59 0.80

1.60 – 1.80 0.35 0.41 0.53 1.00 0.35 0.41 0.53

1.90 – 2.10 – 0.29 0.38 0.86 – 0.29 0.38

2.20 – 2.40 – 0.21 0.28 0.64 – 0.21 0.28

2.50 – 2.70 – – 0.19 0.47 – – 0.19

2.80 – 3.00 – – 0.14 0.37 – – 0.14

Note Width dimensions are ‘inside of channel’ dimensions.



Box Lintels for Solid Walls

WALL WIDTH LINTEL TYPE GAUGE CODE STEEL THICKNESS WEIGHT SAFE WORKING LENGTHS AVAILABLE (mm) (kg per metre) Load (tonnes) (metres)

100mm CN5X A 2.0 7.6 2.0 1.05 to 2.70 except 1.35 in 150mm increments

100mm CN6X B 2.5 12.4 3.0 2.85, 3.00, 3.30, 3.60

100mm CN6X C 3.1 15.7 3.0 3.90, 4.20


140/150mm CN56X A 2.0 9.0 2.0 1.05 to 2.70 except 1.35 in 150mm increments

140/150mm CN66X B 2.5 14.1 3.0 2.85, 3.00, 3.30, 3.60

140/150mm CN66X C 3.1 18.0 3.0 3.90, 4.20



190/200mm CN19/14 A 2.0 2.0 2.0 10.0 2.0 1.05 to 2.10 in 150mm increments

190/200mm CN19/19 B 2.5 2.5 2.0 13.8 3.0 2.25 to 3.00 in 150mm increments

190/200mm CN19/19 C 3.1 3.1 2.0 16.8 3.0 3.30, 3.60, 3.90, 4.20

All lintels illustrated are supplied fully perforated (except top surface) as standard.



Lintels for Cavity Walls


200mm CN71 A 2.0 2.0 1.6 9.3 2.0 1.05 to 2.70 (except 1.95, 2.25) in 150mm increments

200mm CN81 B 2.5 2.5 2.0 15.1 3.0 3.00, 3.30, 3.60

200mm CN81 C 3.1 3.1 2.0 18.5 3.0 3.90, 4.20


For 50-65mm Cavity 100-115mm Inner Leaf

STANDARD LENGTHS (MM) 750-1500 1650-1800 1950-2100 2250-2400 2550-2700 2850-3000 3300-3900

SWL 1:1/3:1 (kN) 15 18 20 22 26 26 26

Weight 5.80 7.34 7.96 8.59 9.84 12.29 16.02

Nominal height ‘h’ (mm) 140 140 160 180 220 220 220

CG50/100

STANDARD LENGTHS (MM) 750-1200 1350-1800 1950-2400 2550-2700 2850-3000

SWL 1:1/3:1 (kN) 12 17 20 26 26

Weight 6.3 7.78 9.03 12.87 16.55

Nominal height ‘h’ (mm) 140 140 180 220 220

CG50/125*

For 50-65mm Cavity 125-140*mm Inner Leaf

CG

CG/H-50/125

CGE-50/125

CU-50/125

nominal height (see tables below)

9548125

‘h’

CG

CG/H-50/100

CU-50/100

CGE-50/100

nominal height (see tables below)

9548100

‘h’CG50/125

CG70/125

CG90/125

CG50/125

CG70/125

CG90/125


Lintels for Internal Partitions


75mm CN92 1.2 1.2 0.7 1.05 & 1.20

100mm CN102 1.2 1.8 0.7 1.05 & 1.20

Catnic corrugated lintels CN92 and CN102 are designed for internal partition walls only and are manufactured from galvanised steel to

BSEN 10327:2004-DX51D+Z275.

These lintels are supplied in plain galvanised steel without powder coating.

NOTE: When using these lintels normal building practice should be observed, in that one course of blockwork (Nominal height 200mm)

should be laid on the lintel and the mortar allowed to harden for at least 24 hours before additional loads are applied.

Lintel Profiles - dimensions in mm.

100

98

25

CN102

75

68

25

CN92

Lintel Brackets

External Application

Brackets are supplied with fixing holes to suit metal expansion

anchor sizes specified in table below.Perforated

Unperforated

CODE REFERENCE SUITABLE FOR LINTELS MAXIMUM LOAD TONNES/BRACKET

SB 02/15P * CN56X, CN66X

0.45 – 0.72 –

SB 02/15P/A1 * – 0.72 – 0.72

SB 02/19P * CN71, CN81, CN19/14, CN19/19

0.50 – 0.88 –

SB 02/19P/A1 * – 0.88 – 0.90

SB 02/24P * CN7, CN8

0.50 – 0.88 –

SB 02/24P/A1 * – 0.88 – 1.04

SB 02/28P * CN11, CN12

0.50 – 0.88 –

SB 02/28P/A1 * – 0.88 – 1.15

Metal expansion anchors quantity - diameter (mm) 2 No. M8 2 No. M10 4 No. M8 4 No. M10

* Unperforated brackets can be supplied on request, simply delete “P” from code reference.

CODE REFERENCE SUITABLE FOR LINTELS MAXIMUM LOAD TONNES/BRACKET

SB 01 * CN5X, CN6X, CN100 0.50 – 0.80 –

SB 01/A1 * CN103, CN102 – 0.88 – 0.90

SB 03 * CN150, CN152

0.50 – 0.80 –

SB 03/A1 * – 0.88 – 0.90

SB 08 * CN200, CN202 0.50 – 0.77 –

Metal expansion anchors quantity - diameter (mm) 2 No. M8 2 No. M10 4 No. M8 4 No. M10

Internal Application

Brackets are supplied with fixing holes to suit metal expansion

anchor sizes specified in table below.


Plaster AccessoriesOur comprehensive range of Plaster Accessories are precision engineered and simple to use. Fixing by nail or plaster dab is straightforward and fast, generating arises, edges, corners and joints that are easy to form and resistant to chipping, cracking and impact damage.



The most appropriate Catnic bead should be chosen to suit the

application, required plaster depth and the desired finish of the work.

The application and installation of Catnic beads should be in

accordance with BS 5492:1990 Code of Practice for internal

plastering and BS 5262:1991 Code of Practice for external

renderings.

Beads may be trimmed to length using tinman’s shears across the

wings and a fine toothed saw across bead noses.

Use one of the following methods to fix Catnic angle beads and

plaster stop beads:

a) Using galvanised or stainless steel nails (compatible with bead

material) complying with BS 1202: Part 1, fixed at a maximum of

600mm apart. When nailing to a solid background the line of the

bead will follow the line of the background.

b) Pressing the bead onto dabs of the same material as the

undercoat. Dabs should be applied at a maximum of 600mm

apart. This method will even out minor irregularities in the line of

the background, although the line of the bead will tend to generally

follow the line of the background.

c) When beads are used with metal lath backgrounds,

galvanised or stainless steel tying wire may be used to

secure the beads in position. Soft galvanised wire to BS

443 and soft stainless steel wire complying with BS 1554

should be used to match the bead and lath materials. All

wires should be twisted tightly and the ends bent away

from the finished face of the coating.

Block

Plaster

Nails 600mm apart (max)

Bead

Block

Plaster

Bead

Concrete dabs 600mm apart (max)(DABS NOT SHOWN TO SCALE IN

RELATION TO BEAD).

How to Install a Catnic Plasterer’s Bead

In normal circumstances, matured plasterwork may be

regarded as dry and therefore non-corrosive. Risks of corrosion

in galvanised accessories only normally become apparent

during the initial plaster drying out period, which should be

kept to a minimum, and subsequently during periods of heavy

condensation.

The use of sand or water contaminated with soluble salts in

plastering mixes should be avoided as should soluble chlorides

as they are likely to increase the risk of metal corrosion. The

presence of sea salts in sand used in plastering which is in

contact with galvanised accessories will often cause rust

staining and should therefore be avoided.

In external applications and, in conditions where heavy

condensation, persistent damp or regular exposure to moisture

are likely, stainless steel, PVC-U or PVC-U nosed products

should be specified.

In general, care should be taken to ensure that metal

accessories are kept dry and distortion is prevented during

storage and handling. Care should also be taken to prevent

mechanical damage to the galvanised coating.

Stainless steel products are for use specifically with cement

based renders. Contact our Technical Services Department

if considering the use of stainless steel beads with Gypsum

plaster.

Corrosion Protection – Plaster Accessories


Angle Beads

CHISEL NOSE ANGLE BEAD ROUND NOSE ANGLE BEAD AB 38

Ref: 4000 4001 AB38

Lengths: 3.0m 3.0m 3.0m

Packing: Shrink film Euro packaged, 25 lenghts/pack Shrink film Euro packaged, 25 lenghts/pack 50 lengths/pack

Application

Angle beads provide true and straight corners which are resistant to chipping and cracking

giving strength and protection against everyday knocks.

Fixing

Fix either by nailing or using plaster dabs as shown in the illustration above.

Quality

Manufactured from galvanised steel to BSEN 10327: 2004 – DX51D+Z275 or Stainless Steel

to BSEN 10088-2-1.4301. All beads shown are manufactured in accordance with BS 6452:

Part 1: 1984.

Angle Bead

34mm

12mm

7.5mm

34mm

12mm

7.5mm

38mm

13mm

5mm

Catnic Galvanised Beads

SUPASAVE ANGLE BEAD STANDARD ANGLE BEAD WIDE WING ANGLE BEAD

Ref: SS STD WW 3.0

Lengths: 2.4m, 2.7m, 3.0m 2.4m, 2.7m, 3.0m 3.0m

Packing: 50 lengths/pack 50 lengths/pack 50 lengths/pack

Angle Beads

SQUARE HOLE ANGLE BEADS SQUARE HOLE ANGLE BEADS SQUARE HOLE ANGLE BEADS Small Nose Small Nose Round Nose

Ref: 4004 4005 4006

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m

Packing: Shrink film Euro packaged Shrink film Euro packaged Shrink film Euro packaged 25 lengths/pack 25 lengths/pack 25 lengths/pack

Square Hole Angle Bead with PVC Nose Square Hole Angle Bead


7mm

30mm

3mm

90º

10mm

40mm

Ø5mm

4mm10mm

30mm

9.5mm

53mm

12 - 19mm

5mm

12 - 19mm

65mm

5mm

45mm

5mm

13mm


Application

Plaster stop beads provide clean, neat edges at openings or abutments onto other wall

surfaces or ceiling finishes. Available to suit plaster thicknesses of 10/13/16/19mm.

Fixing


Quality

Manufactured from galvanised steel to BSEN 10327: DX51D+Z275. All beads shown are

manufactured in accordance with BS 6452: Part 1: 1984.


Plasterstop Bead

PLASTERSTOP BEAD

Ref: PS10 PS13 PS16 PS19

Lengths: 3.0m, 2.7m, 2.4m 3.0m, 2.7m, 2.4m 3.0m, 2.7m, 2.4m 3.0m, 2.7m, 2.4m

Packing: 50 lengths/pack 50 lengths/pack 50 lengths/pack 50 lengths/pack

Plasterstop


10mm 13mm

58mm3mm

Ø4.7mm

55mm3mm

Ø4.7mm

16mm

60mm3mm

Ø4.7mm

19mm

57mm3mm

Ø4.7mm


galvanised - blue

aluminium - lighter grey

stainless steel - blue green

PVC - white

plaster dark

plaster light

8mm

53mm

galvanised - blue



PVC - white

plaster dark

plaster light

53mm

18mm

galvanised - blue



PVC - white

plaster dark

plaster light

53mm

12mm

galvanised - blue



PVC - white

plaster dark

plaster light

110º

13mm

53mm

galvanised - blue



PVC - white

plaster dark

plaster light

110º

53mm

galvanised - blue



PVC - white

plaster dark

plaster light

110º

53mm

PLASTERSTOP PUNCHED WING

Ref: 6212 6213 6214

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m


PLASTERSTOP PUNCHED WING

Ref: 6215 6217 6219

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m


Plasterstop


9mm 18mm

Application

Architrave beads give a shadow line decorative effect for aesthetic purposes and create a

clean division between varying wall finishes eg. at wall and ceiling abutments or door and

window reveals.

Fixing

Fix either by nailing or using plaster dabs.

Quality

Manufactured from galvanised steel to BSEN 10327:2004 – DX51D+Z275.

All beads shown are manufactured in accordance with BS 6452: Part 1: 1984.


Architrave Bead

13mm13mm

37mm

10mm13mm

37mm

ARCHITRAVE

Ref: ARC10/WF/3.0 ARC13/WF/3.0 ARC20/WF/3.0 ARC10/WO/3.0 ARC13/WO/3.0

Lengths: 3.0m 3.0M 3.0M 3.0M 3.0M

Packing: 25 lengths/pack 25 lengths/pack 30 lengths/pack 25 lengths/pack 25 lengths/pack

13mm20mm

37mm

10mm20mm

37mm

13mm20mm

37mm

Architrave


Application

Movement bead allows for movement between adjoining surface finishes resulting from

differential expansion or settlement.

Renderstop beads are used to obtain a neat, bell cast lower edge to external finishes and

helps to protect masonry against run-off water.

Fixing


Quality

Manufactured from galvanised steel to BSEN 10327: 2004-DX51D+Z275.


Movement Bead


Renderstop Bead

MOVEMENT BEAD RENDERSTOP BEAD

Ref: MB10, MB13, RS3.0 MB16, MB19

Steel finish: Galvanised with PVC-U strip Galvanised

Lengths: 3.0m 3.0m

Packing: 10 lengths/pack 50 lenghts/pack

12mm(15mm, 18mm, 21mm)

25mm60°

25mm

45mm

7mm

19mm

RS3.0

Catnic Galvanised BeadsMovement and Renderstop Beads

Application

Provides a quick and accurate means of ensuring consistent, minimum plaster

depths as plaster is simply ‘ruled off’ to leave the required thickness.

Fixing

Fix using galvanised nails.

Quality

Manufactured from galvanised steel to BSEN 10327:2004-DX51D+Z275.

DEPTH GUAGE BEAD DEPTH GUAGE BEAD

Ref: 4100 4101

Lengths: 2.5m, 3.0m 2.5m, 3.0m

Packing: Shrink film Euro packaged, 25 lengths per pack Shrink film Euro packaged, 25 lengths per pack


Depth Guage Bead

21mm

6mm

Ø5mm

Ø3mm

23mm

10mm

Ø5mm

Ø3mm

Catnic Galvanised BeadsDepth Guage Beads


DRYWALL ANGLE BEAD DRY WALL THIN COAT BEAD MICROMESH ANGLE BEAD

Ref: DW DWTC MM

Lengths: 2.4m, 3.0m 2.4M, 3.0M 2.4m, 3.0m


Application

Drywall angle beads are designed for single/thin coat plasterwork, enabling a thin

coat finish of just 3mm.

Micromesh angle beads have fine mesh wings suitable for a single/thin coat of

6mm.

Fixing


Quality

Manufactured from galvanised steel to BSEN 10327:2004-DX51D+Z275. All beads

shown are manufactured in accordance with BS 6452: Part 1: 1984.

Drywall Angle Bead Micromesh Angle Bead

25mm

6mm3mm

23mm

3mm

3mm

85°

Ø4mm

80°

25mm6mm

Ø4mm

3mm

Catnic Galvanised BeadsDrywall and Thin Coat Plaster Applications

Application

Drywall stop beads provide abutments of thin coat (3 or 6mm) plastered areas to other wall

finishes. The scalloped edge provides efficient keying and excellent finish.

Plasterboard edging beads are used to reinforce plasterboard edges and can be

used either with perforated edges to take the final coat of plaster or reversed to take

a simple painted finish. Available for 10 or 13mm board thicknesses.

Fixing


Quality

Manufactured from galvanised steel to BSEN 10327: 2004-DX51D+Z275.


DRYWALL STOP BEAD PLASTERBOARD EDGING BEAD

Ref: DWSB3, DWSB6 PBEB 10, PBEB 13

Lengths: 3.0m 3.0m

Packing: 50 lengths/pack 50 lengths/pack


Drywall Stop Bead Plasterboard Edging Bead

30mm

3mm (6mm)

3mm

25mm

2mm

9.5mm(12.5mm)

12mm (10mm)12mm (15mm)

PBEB13 dimensions in brackets.

Catnic Galvanised BeadsDrywall and Thin Coat Plaster Applications

Angle Bead


65mm

STANDARD ANGLE BEAD WIDE WING ANGLE BEAD

Ref: STD 3.0/SS WW 3.0/SS

Lengths: 3.0m 3.0m


Application

Angle beads provide true and straight corners which are resistant to chipping and cracking

giving strength and protection against everyday knocks.

Fixing

Fix either by nailing or using plaster dabs as shown in the illustration.

Quality

Manufactured from stainless steel to BSEN 10088-2-1.4301.


53mm

5mm

12 - 19mm

5mm

12 - 19mm

Catnic Stainless Steel BeadsAngle Beads


Plasterstop Bead

Application

Plaster stop beads provide clean, neat edges at openings or abutments onto other wall

surfaces or ceiling finishes. Available to suit plaster thicknesses of 10/13/16/19mm.

Fixing


Quality

Manufactured from stainless steel to BSEN 10088-2-1.4301.


PLASTERSTOP BEAD

Ref: PS10/3.0/SS PS13/3.0/SS PS16/3.0/SS PS19/3.0/SS

Lengths: 3.0m 3.0m 3.0m 3.0m

Packing: 50 lengths/pack 50 lengths/pack 50 lengths/pack 50 lengths/pack

58mm

Ø4.7mm

10mm

60mm

Ø4.7mm

16mm

57mm

Ø4.7mm

19mm

55mm

Ø4.7mm

13mm

3mm 3mm3mm

3mm

Catnic Stainless Steel BeadsPlasterstop Beads


Application

Architrave beads give a shadow line decorative effect for aesthetic purposes and creates

a clean division between varying wall finishes eg. at wall and ceiling abutments or door and

window reveals.

Fixing


Quality

Manufactured from Stainless Steel to BSEN 10088 –2-1.4301.


Architrave Bead

13mm13mm

37mm

10mm13mm

37mm

ARCHITRAVE

Ref: ARC10/WF/3.0/SS ARC13/WF/3.0/SS ARC20/WF/3.0/SS ARC10/WO/3.0/SS ARC13/WO/3.0/SS

Lengths: 3.0m 3.0M 3.0M 3.0M 3.0M

Packing: 25 lengths/pack 25 lengths/pack 30 lengths/pack 25 lengths/pack 25 lengths/pack

13mm20mm

37mm

10mm20mm

37mm

13mm20mm

37mm

Catnic Stainless Steel BeadsArchitrave Beads

Application

Movement bead allows for movement between adjoining surface finishes resulting from

differential expansion or settlement. Allowable movement +/- 3mm.

Renderstop beads are used to obtain a neat, bell cast lower edge to external finishes and

helps to protect masonry against run-off water.

Fixing


Quality

Manufactured from Stainless Steel to BSEN 10088-2-1.4301.


Movement Bead Renderstop Bead


MOVEMENT BEAD RENDERSTOP BEAD

Ref: MB10SS, MB13SS, RS3.0 SS MB16SS, MB19SS

Lengths: 3.0m 3.0m

Packing: 10 lengths/pack 50 lenghts/pack

12mm(15mm, 18mm, 21mm)

25mm 60°

25mm

45mm

7mm

19mm

Catnic Stainless Steel BeadsMovement and Renderstop Beads

Square Hole Angle Bead with PVC Nose


Catnic Galvanised Beads with PVC Nose

Angle Beads

SQUARE HOLE ANGLE BEADS

Ref: 6000 6001 6050

Lengths: 2.5m, 3.0m 2.5m, 3.0m 2.5m, 3.0m

Packing: Shrink film Euro packaged Shrink film Euro packaged Shrink film Euro packaged 15 lengths/pack 15 lengths/pack 15 lengths/pack

7mm

30mm

7mm

10mm

41mm

8mm

14mm

41mm

8.5mm

14mm

52mm

8.5mm

SQUARE HOLE ANGLE BEADS

Ref: 6051 STD/PVC

Lengths: 2.5m, 3.0m 2.7m, 3.0m

Packing: Shrink film Euro packaged Shrink film Euro packaged 15 lengths/pack 50 lengths/pack

15mm

53mm

8mm

galvanised - blue



PVC - white

plaster dark

plaster light

53mm

20mm

galvanised - blue



PVC - white

plaster dark

plaster light

53mm

14mm

galvanised - blue



PVC - white

plaster dark

plaster light

10mm

53mm


galvanised - blue



PVC - white

plaster dark

plaster light

110º

14mm

53mm

galvanised - blue



PVC - white

plaster dark

plaster light

110º

53mm

galvanised - blue



PVC - white

plaster dark

plaster light

110º

53mm

PLASTERSTOP BEAD

Ref: 6222 6223 6224

Lengths: 2.7m, 3.0m 2.7m, 3.0m 2.7m 3.0m

Packing: Shrink packed Euro packaged Shrink packed Euro packaged Shrink packed Euro packaged 25 lengths/pack 25 lengths/pack 25 lengths/pack

PLASTERSTOP BEAD

Ref: 6225 6227 6229

Lengths: 2.7m, 3.0m 2.7m, 3.0m 2.7m 3.0m

Packing: Shrink packed Euro packaged Shrink packed Euro packaged Shrink packed Euro packaged 25 lengths/pack 25 lengths/pack 25 lengths/pack

Catnic Galvanised Beads with PVC Edge

10mm 20mm

Catnic PVC Beads

Ø3mm

25mm

plaster depth = 3mm


PVC-U Corner BeadPVC-U Bell Cast Render Bead PVC-U Drywall Corner Arch

13mm

42mm

Ø4mm

5mm

13mm

25mm

3mmØ4mm

3mm

3mm

25mm

Ø3mm

ANGLE BEAD CORNER BEAD

Ref: NR1535 NR1456

Steel finish: PVC-U PVC-U

Lengths: 2.4m, 3.0m 2.4m


PLASTERSTOP BEAD ANGLE BEAD CORNER BEAD

Ref: NR1536 NR1925 NR1660

Steel finish: PVC-U PVC-U PVC-U

Lengths: 2.4m 3.0m 3.0m


Application

PVC-U beads are particularly useful in high humility areas avoiding the possibility of corrosion. They are suitable for both internal and

external use.

Fixing

For thin-coat plaster, beads can be fixed

with staples or joint filler and for thick coat

plaster applications, with either plaster

dabs or nails.

Quality

Beads are manufactured from high density

white PVC-U external window grade.

25mm

50mm

60°

7mm

19mm

25mm

Catnic Expanded Metal Lath

Diamond Lath

Diamond Lath

Expanded metal lath is extensively used as a background to plaster in order to

reinforce against cracks and it is especially useful at joints of dissimilar materials.

Generally DL111 or DL089 lath is used for wall situations and DL161 is used for

ceiling work.

Quality Assurance

Catnic expanded metal lath is manufactured in accordance with BS1369: Part 1:

1987. The galvanised steel used in the manufacture of metal lath is in accordance

with BSEN 10327: 2004 – DX51D+Z275. Where stainless steel is used it is in

accordance with BSEN 10088-2-1.4301.

SHEET LATH CORNER LATHRef: S W Mesh Weight Material Sheet size Ref: Weight Width Material Lengths

DL089 9mm 0.9kg/m2 Galvanised Steel 250 x 70cm LC023/50/2.5 1.61kg/m2 5 x 5cm Galvanised Steel 250cm

DL111 9mm 1.11kg/m2 Galvanised Steel 250 x 70cm LC023/75/2.5 1.61kg/m2 7.5 x 7.5cm Galvanised Steel 250cm

DL161 9mm 1.61kg/m2 Galvanised Steel 250 x 70cm

DL111S 9mm 1.11kg/m2 Stainless Steel 250 x 70cm

STRIP LATH COIL LATHRef: Weight Width Material Lengths Ref: Weight Width Material Lengths

SL021/100/2.5 1.11kg/m2 10cm Galvanised Steel 250cm CL021/100/100 1.11kg/m2 10cm Galvanised Steel 100 metres




CL023/150/100 1.61kg/m2 15cm Galvanised Steel 100 metres

CL023/200/100 1.61kg/m2 20cm Galvanised Steel 100 metres

Sheet Lath Corner Lath Strip Lath

Coil Lath


Rib Lath


RIB LATHRef: Weight Material Size Rib Height

RIB148 1.48kg/m2 Galvanised Steel 250 x 70cm 10mm



RIB148S 1.48kg/m2 Stainless Steel 250 x 70cm 10mm

RIB184S 1.84kg/m2 Stainless Steel 250 x 70cm 10mm

Catnic Expanded Metal Lath

Rib Lath

Rib lath is extensively used as a plaster background for ceilings, walls and

partitions. Generally 148 is suitable for wall situations. For ceiling work 184/222

should be used.

Quality Assurance

Catnic expanded rib lath is manufactured in accordance with BS1369: Part 1: 1987.

The galvanised steel used in the manufacture of rib lath is in accordance with BSEN

10327:2004-DX51D+Z275. Where stainless steel is used it is in accordance with

BSEN 10088-2-1.4301.

Refurbishment of Masonry

Stainless steel rib lath is ideal for refurbishing damaged or aged masonry walls,

when a key for rendering is not certain due to disintegration or softening of the wall

face.

Lath should be fixed with apexes of ribs against the wall, edge ribs of the sheets

nesting into each other should be wire-tied every 15cm and ends of sheets should

be lapped not less than 2.5cm and nesting ribs securely tied together.

Stainless steel fixings should be used at sufficient intervals to hold the lath firmly in

position.

Catnic Mesh Arch Formers – Galvanised

Mesh Arch Formers

The Catnic arch former is the easy way to create attractive and perfectly finished

arches. For walls of up to 160mm thick, the frame sections are designed to be

overlapped. For walls 160-300mm thick, standard infill soffit pieces are provided to

bridge the gap between the sections. If the thickness of the wall is between 300-

565mm, an Extra Soffit piece is available.

Each arch is supplied with installation instructions and a complete fixing kit. Soffit

pieces are also included for walls up to 300mm thick.

Quality Assurance

The galvanised steel used in the manufacture of mesh arch formers is in accordance

with BSEN 10327:2004-DX51D+Z275.

Note: Catnic arches are non-loadbearing, decorative features and will therefore not support walls. If there is any doubt about suitability, please contact us.

60mmBrick to brick

dimension

rise

60mm

Verona

Brick to brick

dimension60mm

rise

60mm

Verona with bridging sections

Extra Soffit Section

610mm

60mm

80mm

295 x 1200mm


Milano

Bridging Section

Catnic Mesh Arch Formers

Brick to brick VERONA MILANOdimension (mm) Ref no. Rise (mm) Ref no. Rise (mm)

750 VE 0750 375

800 VE 0800 400

850 VE 0850 425

900 VE 0900 450

1000 VE 1000 500

1200 VE 1200 600 MI 1200 280

1500 VE 1500 750 MI 1500 330

1800 MI 1800 375

2400 MI 2400 375

Ref Length

BS 061 610mm

Extra Soffit Section

Installation

Ref Size Wall thickness

ES 0295 295 x 1200mm 300 – 565mm

Note: These products are excluded from our BSEN ISO 9001:2000 registration as they are not manufactured on Catnic premises.

> Measure the distance between the walls (brick to brick) and select the appropriate arch size. If renovating,

remove existing plaster down to the masonry. Mark the centre of the aperture.

> Position the first section of the arch to the wall and fix with the masonry nails provided.

> Fix the other sections in the same way, aligning them at the centre with the plastic joining pieces provided.

All arches and soffit pieces should be joined with the self tapping screws provided.

> The arch is completed by plastering directly onto the steel mesh, using a suitable material.

1 2 3 4


Catnic Coil Mesh for Blockwork

Coil Mesh

Anti-crack reinforcement for non-structural use.

Quality Assurance

Manufactured from either galvanised steel to BSEN 10327:2004-DX51D+Z275,

or stainless steel to BSEN 10088-2-1.4301.

Ref: Wall width Coil width Coil length mm mm metres

CM 50 100 50 50 or 20

CM 64 114 64 50 or 20

CM 100 150 100 100 or 20

CM 114 164 114 100 or 20

CM 150 200 150 100 or 20

CM 178 228 178 100 or 20

CM 200 250 200 100 or 20

CM 229 279 229 100 or 20

CM 305 355 305 100 or 20

Coil mesh

Coil mesh


Galvanised & Stainless Steel

Expanded metal type bed joint reinforcement is supplied as an anti-crack

reinforcement in the design and construction of brick and block masonry.

Guidance for its use is given in BS 5628 : Part 3 : 2001 cl.5.4.5

It is generally provided at areas of high stress concentration to dissipate these

stresses to areas of low stress. A typical example would be at a point where the

section of wall changes, such as at a door or window opening. The cracking

of masonry due to changes in temperature, changes in moisture content and

settlement of foundations can all be controlled by the use of block reinforcement.

Catnic Coil Mesh for Non Structural Usage

Wall ConnectorsCatnic’s Wall Connectors are a simple yet effective system for tying new masonry walls to existing walls.


Wall TiesAll Catnic wall ties are manufactured from high quality stainless steel wire and strip materials to ensure that structural design properties are maintained throughout the life of the structure.

Catnic Wall Accessories

Brick and Block Spacer SystemThe revolutionary new way to lay perfect brickwork and blockwork.

Wall Ties – Stainless Steel

Wall Ties

Catnic Wall Ties are manufactured from stainless steel in accordance with

BSEN 10088-2-1.4301 (strip), BSEN 10088-3:2005 min. 18/8 composition (wire).

BB-2 BT 2-4

For fixing masonry to masonry in cavity walls of domestic houses and small commercial buildings of up to five storeys but not exceeding 15m in height. Tie density 2.4 ties/m2. Based on a design windspeed up to56m/s.

Ref Length Width Cavity width Packing

BB-3 220mm 19mm 75mm Cartons of 250

For fixing masonry to masonry in cavity walls of domestic houses and small commercial buildings of up to three storeys but not exceeding 15m in height. Tie density 2.4 ties/m2. Based on a design windspeed up to 56m/s.


BB-2 191mm 19mm 50mm Cartons of 250

For fixing masonry to timber framing in single and two storey dwellings up to a maximum height of 8m. Also suitable for block to concrete applications. Tie density and windspeed refer to BBA certificate.


BT 2-4 120mm 19mm 50mm Cartons of 250

BB-2 DD140 Part 2 Catnic BB-2 1987 type 2 requirement

Tensile Load (N) At serviceability 500 1321

Tensile Load (N) At failure 1800 3183

Comprehensive Load (N) At serviceability 400 552

Comprehensive Load (N) At failure 1300 1300

BB-3


BB-3 DD140 Part 2 Catnic BB-3 1987 type 2 requirement

Tensile Load (N) At serviceability 500 1529

Tensile Load (N) At failure 1800 4051

Comprehensive Load (N) At serviceability 400 1540

Comprehensive Load (N) At failure 1300 2374

Stainless Steel Strip TiesCavity Design Tie Size (mm) Specify DD140: Part 2 Wind Speed

50mm 3 storeys up to 15m 0.6 x 19 x 191 BB-2 Type 2 Up to 56m/s

50mm 5 storeys up to 15m 0.8 x 19 x 220 BB-3 Type 2 Up to 56m/s

50mm 4 storeys up to 12m 0.6 x 19 x 120 BT2-4 Up to 50m/s


Wall ConnectorsGalvanised & Stainless Steel

Wall Connectors

Catnic wall connectors are suitable for wall thicknesses from 60mm up to 250mm

and one pack contains all of the required fixings for a single wall of 2.4m high. This

product is available with a choice of two different materials.

STRONGHOLD WALL CONNECTORS

Ref: SWC

Material Stainless Steel to BSEN 10088-2-1.4301

Packaging 20 packs per carton

GALVANISED WALL CONNECTORS

Ref: GWC

Material Galvanised Steel to BSEN 10327: 2004-DX51D+Z275

Packaging 20 packs per carton

Stronghold Wall Connector Galvanised Wall Connector


Brikmat is the revolutionary new range of masonry support and bed joint reinforcement systems designed to make blockwork a breeze...

Build more with Brikmat

Brikmat

Brikmat is a masonry support system that eliminates

bed joint compression providing a stable platform for

additional courses of physically demanding masonry to

be built.

Guaranteed consistent mortar joint.

Easy to use, no training required.

Increases speed and improves productivity.

Improves accuracy and ensures aesthetic finish.

Brikmat Reinforcement

Brikmat bed-joint reinforcement system increases the

compressive strength and rigidity of the heavy blockwork,

providing a stable platform for additional courses of

physically demanding masonry to be built.

Reinforces and supports heavy blockwork.

Increases the flexural strength of stack-bonded masonry.

Relieves stress concentration around openings.

Allows cladding panels to be increased in size.


Why use Brikmat?

Specifiers

Specify with confidence Specify dense architectural masonry

products with confidence.

Guarantee the aesthetic finish

of your design.

Save time and money for your client.

Eliminate time spent dealing with

block panel issues on site.

Main Contractor

Saves time & money More successive courses in a single lift

equates to improved productivity and

less time on site.

Improve block laying speed up to three

times faster.

Hidden savings Scaffolding down sooner.

Bricklayers off site sooner.

Following trades can be on site sooner.

Mortar silos collected and off site sooner.

Wastage reduction Saving of up to 60% on mortar wastage.

No “bulking up” of joints required.

Minimal bleeding of mortar onto block

face.

Improve accuracy Helps consistency when teams of

bricklayers are working on projects.

Health & safety Improved stability of block panels.

Less mortar on scaffolding boards.

Less mortar dropped below.

No need for chemical cleaning

of stained blockwork.

Bricklayer / Builder

Greater speed Proven to be up to 3 times faster than

conventional building methods.

Improved productivity Build up to 10 courses* of dense

aggregate block work in a single lift

without compression of the mortar

bed-joints at lower levels.

Use a standard mortar mix. No waiting

for mortar to harden before continuing

to build.

Enhanced accuracy A quality finish virtually guaranteed.

Consistent gauge height, even after

10 courses.

Prevents extrusion of the mortar due

to pressure from successive courses

= no mortar bleeding on fair-faced

blockwork = no cleaning!

Ibstock, Fireborn Red


Brikmat fast build, perfect results.

A full copy of the CERAM test report is available on request.

Working with Brikmat Placed in the horizontal bed joints

to increase the stability of physically

demanding masonry, Brikmat resists

the stresses that are inherent in loaded

masonry panels eliminating the risk

of bed joint compression and mortar

bleeding.

Suitable for stretch bonded masonry.

Eliminates bed joint compression.

Reduces mortar bleeding.

Provides increased stability.

Continue building without waiting

for mortar to cure.

Working with Brikmat ReinforcementIn addition to the features of Brikmat,

Brikmat Reinforcement also:

Increases the flexural strength with

stack-bonded masonry.

Increases the recommended distance

between movement joints.

Strengthens areas of concentrated

loads and assist in resisting effects of

stresses caused by earth movements

reducing the likelihood of cracking in

the brickwork.

Allows cladding panels to be increased

in size.

Relieves stress concentration around

openings such as windows and doors.

Independently tested Independent testing conducted by CERAM

Research Limited clearly demonstrated

the tangible benefits of using Brikmat with

physically demanding masonry.

The CERAM report also highlighted:

Walls being built without Brikmat can

be as much as 6mm-10mm out of

plumb on the 5th course.

Walls built with Brikmat use up to 60%

less mortar.

Bed joints in walls built with Brikmat

do not alter in thickness through a

10-course construction.

Walls built with Brikmat can be built up

to 3 times faster than those without the

support of Brikmat.

Brikmat product properties

Product code Length(mm) Width(mm) Gauge Colour Pack Linear metres height (mm) quantity per box(m)

BM9 870 80 9.0 Blue 25 21.75

BM11 870 80 10.7 White 25 21.75

Brikmat Reinforcement product properties

Product code Diameter Width Length Minimum Characteristic Pack (mm) (mm) (mm) X sec area tensile strength quantity (mm2) (n/mm2)

BMR3.0/60 3.0 60 3000 7.07 800 30

BMR3.5/60 3.5 60 3000 9.62 800 30

BMR4.0/60 4.0 60 3000 12.56 800 30

BMR3.0/100 3.0 100 3000 7.07 800 30

BMR3.5/100 3.5 100 3000 9.62 800 30

BMR4.0/100 4.0 100 3000 12.56 800 30

BMR3.0/150 3.0 150 3000 7.07 800 30

BMR3.5/150 3.5 150 3000 9.62 800 30

BMR4.0/150 4.0 150 3000 12.56 800 30


Fencepost Supports


QwikPost Repair Spike QwikPost Concrete-in Support

QwikPost Bolt-down Support

QwikPost Standard Arris bracket

QwikPost U-Clips QwikPost Z-Clips QwikPost Universal Post Extender

QwikPost Drive-in Tool

Fencepost Supports

Fencepost Supports

QwikPost is a durable and affordable fence post fixing system. The range includes:

QwikPost

QWIKPOST SPIKE

Ref SPK5045 SPK7560 SPK7570 SPK1070

Size (mm) 50 x 50 x 450 75 x 75 x 600 75 x 75 x 700 100 x 100 x 700

Packaging 10 per carton 10 per carton 10 per carton 10 per carton

QWIKPOST REPAIR SPIKE QWIKPOST CONCRETE-IN SUPPORT

Ref REP75 CON75 CON100

Size (mm) 75 x 75 75 x 75 100 x 100

Packaging 10 per carton 10 per carton 10 per carton

QWIKPOST COLT-DOWN SUPPORT QWIKPOST STANDARD ARRIS BRACKET

Ref BLT50 BLT75 ARB001

Size (mm) 50 x 50 75 x 75


QWIKPOST U-CLIPS QWIKPOST Z-CLIPS

Ref UCP47 UCP52 ZED001

Size (mm) Small 47mm Large 52mm


QWIKPOST UNIVERSAL POST EXTENDER QWIKPOST DRIVE-IN TOOL

Ref UPE DOL

Size (mm)

Packaging 10 per carton 10 per carton

QwikPost Spike


Catnic

1. Angle bead or corner bead

Galvanised Angle bead shall be manufactured in accordance with BS 6452: Part1: 1984 using galvanised steel to BS EN 10327-DX51D+Z275 with 45mm (53mm: 65mm) wing size as manufactured by Catnic under code reference SS3.0 (STD3.0: WW3.0).

Stainless Angle bead shall be manufactured in accordance with BS 6452: Part1: 1984 using stainless steel to BSEN 10088-2-1.4301 with 53mm wing size as manufactured by Catnic under code reference STD3.0SS.

2. Plasterstop or casing bead

Galvanised Plasterstops shall be manufactured in accordance with BS 6452: Part1: 1984 using galvanised steel to BSEN 10327-DX51D+Z275 and to suit plaster thickness of 10mm (13mm: 16mm: 19mm) as manufactured by Catnic under code reference PS10/3.0 (PS13/3.0: PS16/3.0: PS19/3.0).

Stainless Plasterstops shall be manufactured in accordance with BS 6452: Part1: 1984 using stainless steel to BSEN 10088-2-1.4301 and to suit plaster thickness of 10mm (13mm: 16mm: 19mm) as manufactured by Catnic under code reference PS10/3.0/SS (PS13/3.0/SS: PS16/3.0/SS: PS19/3.0/SS).

3. Architrave beads

Galvanised Architrave beads shall be manufactured in accordance with BS 6452: Part1: 1984 using galvanised steel to BS EN 10327-DX51D +Z275 and to suit plaster thickness of 10mm (13mm) without (with) return flange as manufactured by Catnic under code reference ARC10/WF/3.0 (ARC13/WF/3.0: ARC20/WF/3.0) or ARC10WO/3.0 (ARC13/WO/3.0).

Stainless Architrave beads shall be manufactured in accordance with BS 6452: Part1: 1984 using stainless steel to BSEN 10088-2-1.4301 and to suit plaster thickness of 10mm (13mm) without (with) return flange as manufactured by Catnic under code reference ARC10/WF/3.0/SS (ARC10/WF/3.0/SS, ARC13/W0/3.0/SS, ARC13/WF/3.0/SS, ARC20/WF/3.0/SS.

4. Movement bead

Galvanised Movement beads shall be manufactured in accordance with BS 6452: Part1: 1984 using galvanised steel to BSEN 10327-DX51D+Z275 and to suit plaster thickness of 12mm (15mm: 18mm: 21mm) as manufactured by Catnic under code reference MB10/3.0 (MB13/3.0: MB16/3.0: MB19/3.0).

Stainless Movement beads shall be manufactured in accordance with BS 6452: Part1: 1984 using stainless steel to BSEN 10088-2-1.4301 and to suit plaster thickness of 12mm (15mm: 18mm: 21mm) as manufactured by Catnic under code reference MB10/3.0/SS (MB13/3.0/SS: MB16/3.0/SS: MB19/3.0/SS).

5. Renderstop

Galvanised Renderstops shall be manufactured in accordance with BS 6452: Part1: 1984 using galvanised steel to BSEN 10327-DX51D+Z275 as manufactured by Catnic under code reference RS3.0.

Stainless Renderstops shall be manufactured in accordance with BS 6452: Part1: 1984 using stainless steel to BSEN 10088-2-1.4301 as manufactured by Catnic under code reference RS/3.0/SS.

6. Expanded metal lath

Galvanised Expanded metal lath shall be manufactured in accordance with BS 1369: Part1: 1987 using galvanised steel to BSEN 10327-DX51D+Z275 and weighing 0.90kgs per sq.metre (1.11kgs per sq.metre: 1.61kgs per sq.metre) as manufactured by Catnic under code reference DL080 (DL111: DL161).

Stainless Expanded metal lath shall be manufactured in accordance with BS 1369: Part1: 1987 using stainless steel to BSEN 10088-2-1.4301 and weighing 1.11kgs per sq.metre as manufactured by Catnic under code reference DL111/SS.

7. Rib Lath

Galvanised Rib Lath shall be manufactured in accordance with BS 1369: Part1: 1987 using galvanised steel to BSEN 10327-DX51D+Z275 with 10mm ribs at 100mm centres and weighing 1.48kgs per sq.metre (1.84kgs per sq.metre: 2.22 per sq.metre) as manufactured by Catnic under code reference RIB148 (RIB184: RIB222).

Stainless Rib Lath shall be manufactured in accordance with BS 1369: Part1: 1987 using stainless steel to BSEN 10088-2-1.4301 with 10mm ribs at 100mm centres and weighing 1.48kgs per sq.metre (1.84kgs per sq.metre) as manufactured by Catnic under code reference RIB148/SS (RIB184/SS).

8. Steel lintels

Steel lintels shall be manufactured in accordance with BS 5977: Part2: 1983 using galvanised steel to BSEN 10327-DX51D+Z275 and coated with a thermosetting polyester powder coating as manufactured by Catnic.

Technical Specification ClausesAll backgrounds should be free of deleterious substances such as mould, oil and grease and be adequately prepared to accommodate the finished surface, all beading and attendant fixings at the specified depths.

Catnic beads should be fixed at a nominal 600mm spacing by embedding with dabs of the same material used for the undercoat or corrosion resistant galvanised nails for galvanised bead and stainless steel nails for stainless steel bead.

www.catnic.com

CatnicInternational Sales DepartmentCorus UK LimitedPontypandy EstateCaerphillyCF83 3GLTelephone +44 (0) 29 2033 7900Facsimile +44 (0) 29 2088 0855

Catnic is a Corus Group company. Further Information can be found on the Corus website at www.corusgroup.com

Copyright Corus UK Limited 2007Design: ELEVATOR www.elevatordesign.co.uk

Documents

Catnic Brochure