CCNA 1 Final Exam 2012

7/30/2019 CCNA 1 Final Exam 2012

1/20

CCNA 1 Final Exam 2012

1. When must a router serial interface be configured with the clock rate command?

when the interface is functioning as a DTE device

when the interface timers have been cleared

when the connected DTE device is shut down

when the interface is functioning as a DCE device

2. Refer to the exhibit. A network technician is trying to determine the correct IP address configuration for HostA. What is a valid configuration for Host A?

IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2






3. Refer to the exhibit. What function does router RT_A need to provide to allow Internet access for hosts in thisnetwork?

address translation

DHCP services

ftpd

web server


2/20

4. Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a frame was

captured with the source MAC address 0050.7320.D632 and the destination MAC address 0030.8517.44C4. The

packet inside the captured frame has an IP source address 192.168.7.5, and the destination IP address is

192.168.219.24. At which point in the network was this packet captured?

leaving host A

leaving ATLleaving Dallas

leaving NYC

5. Which range of port numbers are reserved for services that are commonly used by applications that run on

servers?

0 to 255

0 to 1023

1024 to 49151

49152 to 65535

6. Which prompt represents the appropriate mode used for the copy running-config startup-config command ?

Switch-6J>Switch-6J#

Switch-6J(config)#

Switch-6J(config-if)#

Switch-6J(config-line)#


3/20

7. Refer to the exhibit. A technician is working on a network problem that requires verification of the router LAN

interface. What address should be pinged from this host to confirm that the router interface is operational?

127.0.0.1

192.168.64.196

192.168.254.1192.168.254.9

192.168.254.254


4/20

8. Refer to the exhibit. Host A is unable to reach host B on the remote network. A technician attempted to ping the

local gateway and the ping was successful. To verify the host configuration, the technician issued the ipconfig

command. What is the likely cause of the problem?

The local NIC is incorrectly configured.

The subnet mask on host A is incorrectly configured.

The IP address on host A is incorrectly configured.

The default gateway on host A is incorrectly configured.

9. An organization has been assigned network ID 10.10.128.0 and subnet mask 255.255.224.0. Which IP addressrange can be used for this organization?

10.10.128.0 to 10.10.160.25510.10.128.0 to 10.10.159.25510.10.128.0 to 10.10.192.255

10.10.128.0 to 10.10.0.159

10.10.128.0 to 10.10.159.0


5/20

10. Refer to the exhibit. An employee wants to access the organization intranet from home. Which intermediarydevice should be used to connect the organization intranet to the Internet to enable this access?

hub

switch

routerwireless access point

11. Which OSI layer manages data segments?

application layer

presentation layer

session layer

transport layer

12. Which two types of media can provide bandwidth up to 1 Gb/s? (Choose two.)

10 BASE-T

100 BASE-T100 BASE-FX

1000 BASE-TX1000 BASE-SX

13. To enhance security in a network, the network administrator uses these commands:Router(config)# line console 0Router(config-line)#password j1mdi2

Router(config-line)# loginWhat two conclusions are evident from these commands? (Choose two.)

Users who attempt to connect to the console port of the router must enter a password.

The entries permit access through the console by the use of j1mdi2 as the password.

The entries eliminate the need for authentication.

Access through the console will be denied because the console configuration is incomplete.

The entries prevent passwords from being displayed as plain text.


6/20


7/20

16. Refer to the exhibit. Communication for hosts X and Y is restricted to the local network. What is the reason forthis?

Host X is assigned a network address.Host Y is assigned a multicast address.

Host X and host Y belong to different networks.

The gateway addresses are broadcast addresses.

17. A user enters http://www.cisco.com/web1.htm in the address line of a browser. Which statement is trueabout this transaction?

The http portion indicates the protocol that is being used.

The web1.htm portion is the specific service name.

The retrieved web page will be displayed in URL code.

The www.cisco.com is the name of the web page file that is called

18. The tracert 10.1.3.2 command was issued on computer A. Computer A can ping other addresses on the localsubnet. Computer A sent the first ICMP packet toward computer B with a TTL value of 1. A protocol analyzer that

was running on computer B showed that the packet never reached its destination. Why did the packet not reach

the destination?


8/20

There is a TCP/IP problem on computer A.

There is a routing loop between R1 and R2.

R1 does not have a route for the destination network.

The TTL for the packet was decreased to zero by R1.

19. A routing issue has occurred in your internetwork. Which of the following type of devices should be examined

to isolate this error?

access point

host

hub

router

switch

20. Which physical component is used to access and perform the initial configuration on a new unconfigured

router?

Correct answer is option 2.

21. What can the user do from the command prompt, Router(config-line)# ?

Configure one of the network interfaces.

Configure one of the physical or virtual lines.


9/20

Verify the running configuration on the device.

Configure the parameters for one of the routing protocols.

22. Which option shows the PDU that contains the Layer 3 source and destination addressing for a packet? Correct answer is option (image) 3.

23. Refer to the exhibit. The ping 127.0.0.1 command is issued on the local host. What do the ping results

indicate?

The local host can send packets on the local network.

The TCP/IP stack on the local host operates properly.

The local host has full connectivity to the default gateway.

The local host has full connectivity to the remote network.

24. Which topology divides the collision domain and provides full media bandwidth to the hosts in the network?


10/20

Correct answer is option (image) 3.

25. Refer to the exhibit. Which option correctly identifies the network address, range of host addresses, and thebroadcast address for the network that contains host A?



11/20

26. A technician is setting up a workgroup for six users and wants to allow users to share files without setting up

a server. Which application layer protocol will provide for peer-to-peer file sharing in a workgroup?

DNS

SMB

HTTP

DHCP

27. Which router component will have contents erased when the command erase startup-config is issued?

flash

RAM

ROM

NVRAM

28. Refer to the exhibit. Host1 is in the process of setting up a TCP session with Host2. Host1 has sent a SYN

message to begin session establishment. What happens next?

Host1 sends a segment with the ACK flag = 0, SYN flag = 0 to Host2.





12/20



29. How many host addresses may be assigned when using the 128.107.0.0 network address with a subnet mask

of 255.255.248.0?

30

256

20462048

4094

4096

30. Refer to the exhibit. Host A is able to access resources on the local LAN but is unable to access any resourceson the Internet. What is the likely cause of this problem?

The host subnet mask in incorrect.

The network uses private addresses.

The host address is a network address.

The default gateway is on a different subnet from the host.

31. What is described by the network access layer of the TCP/IP model?

rules for packet acknowledgment, error recovery, and sequencing

rules for the handoff from the internet layer to the network access protocols

rules for how source and destination hosts exchange data between programs

rules for determining which processes can be used to route messages through an internetwork

32. Which two factors contribute to the increased throughput when all nodes of a LAN are connected to a switch

instead of a hub? (Choose two.)

full-duplex operation

collision-free environment

logical bus media access

broadcast-free environment

point-to-multipoint topology


13/20

33. Which application layer protocol allows administrators to log into a server from remote locations and control

a server as though logged in locally?

DNS

FTP

DHCP

SMTP

Telnet

34. A network technician has made a UTP cable that is terminated as T568A on one end and T568B on the

opposite end. What type of cable has been constructed?

patch

console

crossover

straight-through

35. Which application belongs to the category of the client/server model?

using Telnet to access a router

exchanging information via instant messaging

printing a document to a locally connected printer

scanning a document with a directly connected scanner

36. Refer to the exhibit. Which two layers of the OSI model describe the same functions as the transport and

internet layers of the TCP/IP model? (Choose two.)

application layer

presentation layer

session layer

transport layernetwork layer

data link layer

physical layer

37. What command can be used to troubleshoot domain name resolution issues?

get

arp -a

tracert


14/20

nslookup

38. Refer to the exhibit. For connecting two routers with an Ethernet crossover cable, which interface should be

used?

A

B

C

D

39. A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of

password would require this login and be considered the most secure?

console

enable

enable secret

VTY

40. Which three addresses belong to the category of public IP addresses? (Choose three.)

127.0.0.1

196.1.105.6132.11.9.99

10.0.0.1

172.16.9.10

46.1.1.97

41. A network administrator is configuring several switches for a network. The switches have similar

configurations and only minor differences. The administrator wants to save all commands that are issued on the

first switch to a text file for editing. Which transfer option should be selected in HyperTerminal?



15/20

42. Which option represents a point-to-point logical topology diagram?



16/20


17/20

43. Refer to the exhibit. What two facts can be determined from the session information that is displayed?

(Choose two.)

The protocol is a connection-oriented protocol.This exchange is part of the three-way handshake.

The SYN flag is representing the initial establishment of a session.

The destination port indicates that an FTP session has been initiated.

The source port does not support communication with the destination port that is listed.

44. Which communication tool allows real-time collaboration?

wiki

e-mail

weblog

instant messaging

45. Which prompt is associated with the privileged exec mode?

R1>

R1#

R1(config)#

R1(config-router)#

46. What is the effect of the command copy running-config tftp?

copies the configuration from a remote machine into RAM

copies the configuration from a remote machine into NVRAM

copies the configuration currently in RAM to a remote machine

copies the configuration currently in NVRAM to a remote machine


18/20

47. Refer to the exhibit. Which type of network design is shown?

client/server

wide area

dedicated server

peer-to-peer

48. Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1 using Telnet.

Which statement is true about this connection?

The data is automatically encrypted.

A Telnet server process is running on PC1.

The connection is made through a VTY session on the router.

A GET request was sent to RouterB to retrieve data during this session.

49. Refer to the exhibit. A network technician wants to connect host A to the console of a Cisco switch to initialize

the configuration. What type of cable is required for this connection?

straight-through cable

crossover cable

rollover cable

serial cable

50. A technician makes several changes to the running configuration on a router, but the desired results are notachieved. The technician issues the reload command. What action will be taken by the router?

All changes will be lost and the router will restart immediately.

Changes will be saved automatically and the router will restart.

The user will be prompted to save changes before the router restarts.

The router will detect changes to the running configuration and will reload using the configuration stored in RAM.


19/20

Refer to the exhibit. A student has wired each end of a CAT 5e cable as shown. What is the result? (Choosetwo.)The cable is unusable and

must be rewired.The cable is suitable for use as a rollover cable.The cable is suitable for use as a Fast Ethernet crossover.The cable is suitable

for use as a Gigabit Ethernet straight-through.The cable is suitable for use between two 100 Mbps Auto-MDIX capable switches.

10

What is the protocol data unit that is associated with the data link layer of the OSI reference model?dataframepacketsegment

11

Refer to the exhibit. Which list refers only to end devices?D,E,F,GA,H,B,CA,D,E,FA,D,E,G

12

Refer to the exhibit. The serial interface of the router was configured with the use of the commands that areshown. The router cannot ping

the router that is directly connected to interface serial 0/0/0. What should thenetwork technician do to solve this problem?Configure the

description at interface serial 0/0/0.Configure an IP address on interface serial 0/0/0.Remove the

no shutdown

command at interface serial 0/0/0Reboot the router.

13

How many host addresses may be assigned when using the 128.107.0.0 network address with a subnet mask 255.255.248.0?30
http://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtml


20/20

2562046204840944096

14

Refer to the exhibit. Host A and B are unable to communicate with each other. What is the reason for this?Host A is assigned a network

address.Host B is assigned a multicast address.Host A and host B belong to different networks.The gateway addresses are network

addresses.
http://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtmlhttp://assessment.netacad.net/virtuoso/delivery/pub-doc/exam.shtml

Documents

CCNA 1 Final Exam 2012