CCS _ View topic - impossible to use RB0 as interrupt

CCS :: View topic - impossible to use RB0 as interrupt http://ccsinfo.com/forum/viewtopic.php?t=27889&highlight=inte...

1 от 6 01.3.2007 г. 10:20

FAQ Forum Help Official CCS Support Search Register

Profile Log in to check your private messages Log in

impossible to use RB0 as interrupt

CCS Forum Index -> General CCS C Discussion

View previous topic :: View next topic

Author Message

doudlap

Joined: 10 Aug 2006Posts: 7

impossible to use RB0 as interruptPosted: Thu Aug 10, 2006 1:19 pm

With the code below, I have a problem, I never pass into my interrupt fonction.

Do you know my problem ?

--------------------------------------------------------

Code:

#device adc=8

#FUSES NOWDT //No Watch Dog Timer #FUSES #use delay(clock=16000000) #use rs232(baud=9600,parity=N,xmit=PIN_B5,rcv=PIN_B2,bits=9)

//Global declares static int x;

#int_ext void INTRB0(void);

main()

{ ext_int_edge(H_TO_L); enable_interrupts(INT_EXT); clear_interrupt(INT_EXT); // Add this line enable_interrupts(GLOBAL);

while(true) { printf("%d",x); delay_ms(1000); } }

#INT_EXT void INTRB0() { x = 999; printf("%d",x); delay_ms(500); }

rnielsen

Joined: 23 Sep 2003

Posted: Thu Aug 10, 2006 1:25 pm

http://ccsinfo.com/forum/viewtopic.php?t=27889&highlight=inte


2 от 6 01.3.2007 г. 10:20

Posts: 430Location: Utah

Try moving the body of the ISR _above_ main() and don't declare it as a function.

Ronald

________________

You know you're old when you can remember 'Five and Dime' stores.

doudlap



Ok, I have change but my value x no change. Have you got an another idea ?

Code:

#FUSES NOWDT //No Watch Dog Timer #FUSES #use delay(clock=16000000) #use rs232(baud=9600,parity=N,xmit=PIN_B5,rcv=PIN_B2,bits=9)

//Global declares static int x;

#int_EXT EXT_isr() {

x = 999; printf("%d",x); delay_ms(2500); }

main()

{ ext_int_edge(L_TO_H); enable_interrupts(INT_EXT); clear_interrupt(INT_EXT); // Add this line enable_interrupts(GLOBAL);

while(true) { printf("%d",x); delay_ms(1000); } }

thank for all

doudlap

PCM programmer

Joined: 06 Sep 2003Posts: 6775


See this thread: http://www.ccsinfo.com/forum/viewtopic.php?t=27868

doudlap



okay I have review my code but no success. question : The pin rb0 of the pic 16f88 will be interrupted by this interruption ?

My new code tested is :

Code:


http://www.ccsinfo.com/forum/viewtopic.php?t=27868


3 от 6 01.3.2007 г. 10:20

#include <16F88.h> #device adc=8 #FUSES NOWDT //No Watch Dog Timer #FUSES #use delay(clock=16000000)

#int_EXT EXT_isr() {

output_high(PIN_B7); }

#use delay(clock=16000000)

main()

{

output_low(pin_b7); enable_interrupts(INT_EXT); enable_interrupts(GLOBAL);

while(true) {

} }

rnielsen

Joined: 23 Sep 2003Posts: 430Location: Utah


Add NOLVP to your Fuses. There might be other Fuses that should be inserted as well.

Don't use delay() or printf() in an ISR.

Are you sure you should be using 9bits in your RS232?

You don't need the clear_interrupt() command.

You're trying to stuff a value of 999 into a variable that can only accomodate a max of 255.

Have something like:

x++;

in your ISR to see if it is changing when an interrupt happens.

You don't need 'static' when you declare a Global variable.

Is this the entire program or have you edited things out just to post it? It won't work as you've

posted it because you don't have your oscillator Fuse in there among some other setup commands.

Does the program even send anything to the RS232 or does it just sit there acting dead? If it'sdead then you definately don't have all of the Fuses and setup commands that are needed.

Post a _complete_ program including all Fuses and setup commands.

Ronald

jspencer

Joined: 22 Dec 2003Posts: 59Location: Boise, ID USA


First thing I would try is to use the project wizard as it will help you setup your project with the options that you need. This is what I got from the project wizard with just a couple of lines that I

added.

Code:



4 от 6 01.3.2007 г. 10:20

#include <16F88.h> #device adc=8

#FUSES NOWDT //No Watch Dog Timer #FUSES HS //High speed Osc (> 4mhz) #FUSES PUT //Power Up Timer #FUSES MCLR //Master Clear pin enabled #FUSES NOBROWNOUT //No brownout reset #FUSES NOLVP //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O #FUSES NOCPD //No EE protection #FUSES NOWRT //Program memory not write protected #FUSES NODEBUG //No Debug mode for ICD #FUSES NOPROTECT //Code not protected from reading #FUSES NOFCMEN //Fail-safe clock monitor disabled #FUSES NOIESO //Internal External Switch Over mode disabled

#use delay(clock=16000000)

int8 b_flag;

#int_EXT EXT_isr() { b_flag = TRUE; }

void main() {

setup_adc_ports(NO_ANALOGS|VSS_VDD); setup_adc(ADC_OFF); setup_spi(FALSE); setup_timer_0(RTCC_INTERNAL|RTCC_DIV_1); setup_timer_1(T1_DISABLED); setup_timer_2(T2_DISABLED,0,1); setup_comparator(NC_NC_NC_NC); setup_vref(FALSE); enable_interrupts(INT_EXT); enable_interrupts(GLOBAL); setup_oscillator(False);

ext_int_edge(H_TO_L); // or L_TO_H output_low(PIN_B7); b_flag = FALSE; while (1) { if (b_flag) { output_high(PIN_B7); delay_ms(2000); // reset to catch next interrupt output_low(PIN_B7); b_flag = FALSE; } }

}

Looking at your code you are definitely missing a fuse setting for your crystal/oscillator.

I'm not sure that your pic is even running.

doudlap



I haven't use CCS before, so I'am sorry for this problem.

It's the full program. and I search to use the pin B0 as an interrupt because when I will find the solution, i will use all pin of port A and B.

but, actually I'm testing the solution with the software proteus. And can use interrupt whit RB4 to RB7. So i think is a problem in my source code.

in the last code, I have delete the delay and the Rs232.

but the interruption is never call.



5 от 6 01.3.2007 г. 10:20

doudlap



jspencer, before testing lots of possibilites, I used the wizard but no result.

I will test your source code in a real pic and not b the software PROTEUS Because I copy/paste

your code but th interrupt no work I don't know why.

oh I have made a new test. I take a 16f876 and the code work perfectly. So why with a 16f88

the result no work ?

probebly the software proteus no work well why the pic 16f88 ??

doudlap


Posted: Fri Aug 11, 2006 12:23 am

nobody have an idea ?

ckielstra

Joined: 18 Mar 2004Posts: 1334Location: The Netherlands


doudlap wrote:

nobody have an idea ?

You said you were going to try on real hardware instead of in the Proteus simulator. How did this

test go?

Which version number of the CCS compiler are you using? (see the top of the *.lst file to find

this number, it looks like 3.xxx).

doudlap



my version is 3.249 t's possible that come of my version ?

Christophe

Joined: 10 May 2005Posts: 248Location: Varsenare, Belgium


1. don't use delay_ms ( ) function inside ISR (). It makes your software hang, you can find an explanation of that using the forum search function

2. Measure with a scope on pin RB0 of your PIC. Is it wired OK ? Measure if you have a transition. Should be on PIN 6 of your IC.

http://ww1.microchip.com/downloads/en/DeviceDoc/30487c.pdf

3. Your PIC is dead?

Try to implement jspencer's code

gl

Display posts from previous: All PostsAll Posts Oldest FirstOldest First Go

CCS Forum Index -> General CCS C Discussion All times are GMT - 6 Hours

Page 1 of 1

Jump to: General CCS C DiscussionGeneral CCS C Discussion Go

You can post new topics in this forumYou can reply to topics in this forum


http://ww1.microchip.com/downloads/en/DeviceDoc/30487c.pdf


6 от 6 01.3.2007 г. 10:20

You cannot edit your posts in this forumYou cannot delete your posts in this forum

You cannot vote in polls in this forum

Powered by phpBB © 2001, 2005 phpBB Group


Documents

CCS _ View topic - impossible to use RB0 as interrupt