Upload
mackenonnhe
View
3
Download
0
Embed Size (px)
Citation preview
92027E.fm/2 Updated: 08/07/03
ManageLighting management
CDPPresence detector
FunctionThe CDP controls switching on and off of lighting according to the presence of a person and ambient brightness.
It allows detection:� of presence (zone A), the system detects the slightest motions� of movements (zone B), the system detects movements.
The CDP controls switching on of lighting if presence is detected and if ambient brightness is less than the set threshold. It controls switching off of lighting if the outside light becomes greater than the threshold, even in the event of movement.
Data� Power supply: 230 V ±10 %, 50 Hz.� Detection angle:� horizontal 360 °� vertical 180 °.� Recommended floor/ceiling clearance: 2.5 to 3 m.� Maximum range for recommended clearance:� 4 m diameter presence detection zone (small motions)� 24 m diameter movement detection zone (movements).� Setting the brightness threshold for lighting control: 20 to 1300 lux.� Setting the time delay between the last movement detected and switch-off of lighting: 4 seconds to 15 minutes.� Lighting power:� incandescent lights: 2000 W� LV halogen lights (230V) and ELV (12V): 1000 W� fluorescent lights with conventional ballast: 1000 W (cos ϕ = 0.5)� fluorescent lights with parallel corrected ballast: 500 W (cos ϕ = 0.5)� other lights or higher powers: relays compulsory.� Degree of protection: IP 20.� Operating temperature: -15°C to +55°C.� Storage temperature: -25°C to +70°C.� Consumption: <1 W.� Weight: 144 g.� Dimensions:� diameter: 120 mm� height: 70 mm� fixing centre distance: 81 mm.
Catalogue number
E57
525
0592
33N
HD
3601m1 m 2 m2 m12 m 12 m0
AB B
Type Catalogue number
CDP 16992
E57
512 LN
N L L
CDP
92027E.fm/3Updated: 08/07/03
ManageLighting management
CDPtPresence detector
FunctionThe CDPt reserved for installations with 1-10 V control ballast, regulates lighting intensity according to the presence of a person and ambient lighting. It maintains ambient brightness at a level set by lighting intensity variation.The TDP remote control allows manual monitoring of lighting independently of detector settings.
It allows detection:� of presence (zone A), the system detects the slightest motions� of movements (zone B), the system detects movements.
Data� Power supply: 230 V ±10 %, 50 Hz.� Detection angle:� horizontal 360 °� vertical 180 °.� Recommended floor/ceiling clearance: 2.5 to 3 m.� Maximum range for recommended clearance:� 4 m diameter motion detection zone (small presence)� 24 m diameter movement detection zone (movements).� Setting the brightness threshold for lighting control: 100 to 1300 lux.� Setting the time delay between the last movement detected and switch-off of lighting: 4 seconds to 15 minutes.� Lighting power (number of 1-10 V ballasts):� 16 x (1 x 36 W)� 12 x (1 x 58 W)� 12 x (2 X 36 W)� 8 x (2 x 58 W).� Degree of protection: IP 20.� Operating temperature: -15°C to +55°C.� Storage temperature: -25°C to +70°C.� Consumption: <1 W.� Weight: 144 g.� Dimensions:� diameter: 120 mm� height: 70 mm� fixing centre distance: 81 mm.
� Remote control (TDP):� range: 4 m� power supply: 2 x LR03-1.5 V batteries (not supplied).
Catalogue number
E57
525
0592
35N
HD
3601m1 m 2 m2 m12 m 12 m0
AB B
Type Catalogue number
CDPt (with remote control) 16994TDP (additional remote control) 16995
E57
511
LN
LN L
CDPt
1-10 V
92027E.fm/4 Updated: 08/07/03
ManageLighting management
CE30Movement detector
FunctionThe CE30 controls switching on and off of lighting by detection of movements of people and according to ambient brightness.
The CE30 controls switching on of lighting if a movement is detected and if the ambient brightness is less than the pre-set threshold.
After the last movement detected, it controls switching off of lighting on completion of a time delay that can be set beforehand.
Data� Power supply: 230 V ±10 %, 50…60 Hz.� Detection angle: 20°.� Range: 30 m.� Setting of the brightness threshold for lighting control: 5 to 300 lux.� Setting of the time delay between the last movement detected and switching off of lighting: 40 seconds to 8 minutes.� Output contact:� 10 A cos ϕ = 1� 5 A cos ϕ = 0.5� incandescent lights: 2200 W� other lights or higher powers: relays compulsory.� Degree of protection: IP43.� Connection: 1.5 mm² spring tunnel type terminals.� Consumption: < 1 W.� Operating temperature: - 25…+ 55°C.� Approvals: VDE-SEMKO-KEMA-KEUR.
Catalogue number
DB
1000
8902
4541
d
no detection zone
5beams
1beam
Type Catalogue number
CE30 57655
DB
1000
86
92027E.fm/5Updated: 08/07/03
ManageLighting management
0CDMMovement detector
FunctionThe CDM controls switching on and off of lighting by detection of movements of people and according to ambient brightness.
The CDM controls switching on of lighting if a movement is detected and if the ambient brightness is less than the pre-set threshold.
After the last movement detected, it controls switching off of lighting on completion of a time delay that can be set beforehand.
Data� Power supply: 230 V -10 % +6 %, 50…60 Hz.� Detection angle: 0°…180°, configuration of detection angle by cover cut-out.� Range: 0…12 m according to slope adjustment.� Setting of the brightness threshold for lighting control: 3 to 80 lux.� Setting of the time delay between the last movement detected and switching off of lighting: 4 seconds to 15 minutes.� Lighting power:� incandescent lights: 1000 W� LV halogen lights: 500 W� other lights or higher powers: relays compulsory.� Degree of protection: IP54.� Connection: screw terminals up to 2.5 mm².� Consumption: <1.1 W.� Operating temperature: - 25…+ 50 °C.� Approvals: VDE-SEMKO-KEMA-KEUR.
Catalogue number
E63
395
E63
396
0557
40
Type Catalogue number
CDM 16990
DB
1000
12
92027E.fm/6 Updated: 08/07/03
ManageLighting management
CDM 180Movement detector
FunctionThe CDM 180 is installed on the façade. It has a detection range of 180°.It controls:� automatic switch-on of lighting, if a moving person is detected and if ambient brightness drops below a pre-set threshold� automatic switch-off of lighting, after the last movement detected and according to the time delay setting.
Data� Power supply: 230V -10%, 50/60 Hz.� Detection angle: 0° to 180°, configuration of detection angle by cover cut-out.� Max. range: 12 m according to slope adjustment and installation height (2.5 m).� Setting the brightness threshold for lighting control: 2 to 1000 lux.� Setting the time delay between the last movement detected and the lighting switch-off: 5 seconds to 12 minutes.� Lighting power:� incandescent lights: 1000 W� LV halogen lights: 1000 W� fluorescent lights with parallel corrected ballast: 10 x 40 W (cos ϕ = 0.5)� other lights or higher powers: relays compulsory.� Degree of protection: IP44.� Insulation class: class II.� Consumption: < 0.5 W.� Connection: 2 x 1.5 mm2 flexible or rigid cables.� Operating temperature: -20°C … +40°C.
Catalogue number
DB
1000
02D
B10
0003
PB
1001
34
Type Catalogue number
CDM 180 16974
DB
1000
90
92027E.fm/7Updated: 08/07/03
ManageLighting management
0CDM 270 Movement detector
FunctionThe CDM 270 is installed in the corner. It has a detection range of 270°.It controls:� automatic switch-on of lighting, if a moving person is detected and if ambient brightness drops below a pre-set threshold� automatic switch-off of lighting, after the last movement detected and according to the time delay setting.
Data� Power supply: 230V ±10%, 50 Hz.� Detection angle: 0° to 270°, configuration of detection angle by cover cut-out.� Max. range: 12 m according to installation height (2.5 m).� Setting the brightness threshold for lighting control: 2 to 2000 lux.� Setting the time delay between the last movement detected and the lighting switch-off: 10 seconds to 15 minutes.� Lighting power:� incandescent lights: 2000 W� LV halogen lights: 2000 W� fluorescent lights with parallel corrected ballast: 500 W (cos ϕ = 0.5)� other lights or higher powers: relays compulsory.� Degree of protection: IP54.� Insulation class: class II.� Consumption: < 0.8 W.� Connection: 2 x 1.5 mm2 flexible or rigid cables.� Operating temperature: -20°C … +50°C.
Catalogue number
DB
1000
00D
B10
0001
PD
1001
35P
B10
0197
Type Catalogue number
CDM 270 16975
DB
1009
1
92027E.fm/8 Updated: 08/07/03
ManageLighting management
0CDM 360 Movement detector
FunctionThe CDM 360 is installed on the ceiling. It has a detection range of 360°.It controls:� automatic switch-on of lighting, if a moving person is detected and if ambient brightness drops below a pre-set threshold� automatic switch-off of lighting, after the last movement detected and according to the time delay setting.
Data� Power supply: 230V ±10%, 50 Hz.� Detection angle: 0° to 360°, configuration of detection angle by cover cut-out.� Max. range: 12 m according to installation height (2.5 m).� Setting the brightness threshold for lighting control: 2 to 2000 lux.� Setting the time delay between the last movement detected and the lighting switch-off: 10 seconds to 15 minutes.� Lighting power:� incandescent lights: 1000 W� LV halogen lights: 1000 W� fluorescent lights with parallel corrected ballast: 500 W (cos ϕ = 0.5)� other lights or higher powers: relays compulsory.� Degree of protection: IP54.� Insulation class: class II.� Consumption: < 0.8 W.� Connection: 2 x 1.5 mm2 flexible or rigid cables.� Operating temperature: -20°C … +50°C.
Catalogue number
DB
1000
07D
B10
0008
PB
1001
33
Type Catalogue number
CDM 360 16976
DB
1000
92
additional information
choice table: page 92321/2practical advice: page 92311/2dimensions: page 90149/2