Upload
alanagp
View
258
Download
0
Embed Size (px)
Citation preview
SERVICE MANUAL
COMPACT DISC CHANGER SYSTEM
SPECIFICATIONS
CDX-565MXRF
Model Name Using Similar Mechanism CDX-757MX
CD Drive Mechanism Type MG-251B-137
Optical Pick-up Name KSS-720A
US ModelCanadian Model
E ModelVer 1.1 2002.06
9-873-927-02 Sony Corporation2002F0500-1 e Vehicle Company
C 2002.06 Published by Sony Engineering Corporation
CD changer (CDX-565MXRF)System Compact disc digital audio
system
Transmitting frequency 88.3 MHz/88.5 MHz/88.7 MHz/88.9 MHz/89.1 MHz/89.3 MHz/89.5 MHz/89.7 MHz/89.9 MHz/(switchable)
Input/output terminals Wired remote control (8 pin)RF signal (FM) outputPower input (3 pin)
Current drain 900 mA (at playback)900 mA (at disc loading/ejecting)
Operating temperature –10°C to +55°C (14°F to 131°F)Dimensions Approx. 262 × 90 × 185 mm (10
3/ 8 × 3 5/ 8 × 7 3/ 8 in.)(w/h/d)
Mass Approx. 2.1 kg (4 lb. 10 oz.)
Relay boxInput/output Antenna input terminal
Antenna output cordCD Changer input cord
Dimensions 40 × 40 × 27 mm(1 5/ 8 × 1 5/ 8 × 1 1/ 8 in.)(w/h/d)
Mass 140 g (5 oz.)
Wired remote (RM-X83RF)/Wireless remote (RM-X84RF)Dimensions Wired remote:
Approx. 127.5 × 41.5 × 24 mm(5 1/ 8 × 1 11/ 16 × 31/ 32 in.)(w/h/d)Wireless remote:Approx. 52 × 8.5 × 90 mm(2 1/ 16 × 3/ 8 × 3 9/ 16 in.)(w/h/d)
Mass Wired remote:Approx. 280 g (10 oz.)Wireless remote:Approx. 30 g (1 oz.)
Battery Wireless remote:Lithium battery (CR2025)
Supplied accessoriesDisc magazine (1)Parts for installation andconnections (1 set)
Design and specifications are subject to changewithout notice.
Laser Diode PropertiesMaterial GaAlAsWavelength 780 nmEmission Duration ContinuousLaser output power Less than 44.6 µW*
* This output is the value measured at a distance of200 mm from the objective lens surface on theOptical Pick-up Block.
2
CDX-565MXRF
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTEDES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉDE FONCTIONNEMENT. NE REMPLACER CES COM-POSANTS QUE PAR DES PIÈCES SONY DONT LESNUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous ra-diation exposure.
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-static breakdown because of the potential difference generated bythe charged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focusedon the disc reflective surface by the objective lens in the opticalpick-up block. Therefore, when checking the laser diode emis-sion, observe from more than 30 cm away from the objective lens.
US/Canadian model:If the optical pick-up block is defective, please replace the wholeoptical pick-up block.Never turn the semi-fixed resistor located at the side of opticalpick-up block.
OPTICALPICK-UPBLOCK
SEMI-FIXEDRESISTOR
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTSWHOSE PART NUMBERS APPEAR AS SHOWN IN THISMANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
DISC MAGAZINE GETTING OUT PROCEDUREON THE POWER SUPPLY IS OFF
Remove the CASE (LOWER. T) beforehand
1) Press the lever (ML.S) assy in the direction of arrow A.2) Removal the magazine assy.Note: Take out the magazine only when the tray is completely within the
magazine. If the disk or tray is sticking out, turn on the power andeject the magazine.
Lever (ML.S)
Magazine assy
A
power supply cord (J-2502-058-2)
compact disc changer
RF output cord (J-2502-058-1)
wired remote commander
JIG ON REPAIRINGWhen repairing this set, connect the jig (cord) for RF output ex-tract (Part No. J-2502-058-1) and power supply (Part No. J-2502-058-2) as the figure shown below.
3
CDX-565MXRF
TEST DISCThis set can playback a CD-R, CD-RW for audio use. When testthis set, use the following test disc.Test disc for CD-R: TCD-R082LMT (Part No.: J-2502-063-1)Test disc for CD-RW: TCD-W082L (Part No.: J-2502-063-2)
Audio CD
MP3 files
Notes on CD-R discs• You can play CD-Rs/CD-RWs (recordable CDs/rewritable CDs)
H).• Some CD-Rs (depending on the equipment used for its recording
• You cannot play a CD-R that is not finalized*.• A CD-R/CD-RW to which a session can be added can be played.
* A process necessary for a recorded CD-R disc to be played on the audio
H
on this unit (fig.
or the condition of the disc) may not play on this unit.
CD player.
1
2
6
3
5
7
1
2
6
7
4
8
3
5
8
4
9
About MP3 files
Tree 1 Tree 2 Tree 3 Tree 4 Tree 5(root)
Folder (album)
MP3 file (track)
MP3 (MPEG 1 Audio Layer-3) is a standard technology and format forcompressing a sound sequence. The file is compressed to about 1/10 of itsoriginal size. Sounds outside the range of human hearing are compressedwhile the sounds we can hear are not compressed.
Notes on discsYou can play MP3 files recorded on CD-ROMs, CD-Rs (recordable CDs),and CD-RWs (rewritable CDs). The disc must be in the ISO 9660*1 level 1 orlevel 2 format, or Joliet or Romeo in the expansion format. You can use adisc recorded in Multi Session*2.
*1 ISO 9660 FormatThe most common international standard for the logical format of filesand folders on a CD-ROM.There are several specification levels. In Level 1, file names must be inthe 8.3 format (no more than eight characters in the name, no more thanthree characters in the extension “.MP3”) and in capital letters. Foldernames can be no longer than eight characters. There can be no morethan eight nested folder levels.In level 2, file names can be up to 31 characters long (including thedelimiter, the dot “.”, and the extension “. MP3”). Each folder can haveup to 8 trees.For Joliet or Romeo in the expansion format, make sure of the contentsof the writing software, etc.
*2 Multi SessionThis is a recording method that enables adding of data using the Track-At-Once method. Conventional CDs begin at a CD control area calledthe Lead-in and end at an area called Lead-out. A Multi Session CD is aCD having multiple sessions, with each segment from Lead-in to Lead-out regarded as a single session.CD-Extra: A format that contains audio tracks (audio CD data) in
Session 1, and a data track in Session 2.Mixed CD: A format that contains a data track and audio tracks (audio
CD data) in a session.Notes• If MP3 files and Audio data are mixed in a disc, the first identified
file or data will be played back.• With formats other than ISO 9660 level 1, folder names or file
names may not be displayed correctly.• When naming, be sure to add the file extension “.MP3” to the file
name.• If you put the extension “.MP3” to a file other than MP3, the unit
cannot recognize the file properly and will generate random noisethat could damage your speakers.
The playback order of the MP3 filesThe playback order of the folders and files is shown in the illustrationabove.Notes• A folder that does not include an MP3 file is skipped.• If you playback an MP3 file before the information on all the CDs
in the disc magazine has been read, and then set the ignition toOFF or select another source, the beginning of the current trackmay play back when you resume playback.
• The unit reads the disc information (the number of folders andfiles, or the location of the data) before playback of an MP3 file. Itmay take more time to start playback of a disc with a complex filestructure.
• When a disc magazine is inserted into the CD changer or the resetbutton of the connected car audio is pressed, the unit willautomatically be activated and read the information on the CDs.When the information on all the CDs in the disc magazine hasbeen read, the unit will automatically stop operation. The unitfirstly reads all of the disc information in the disc magazine.Depending on the recording method, it may take some time tostop the operation even if you set the ignition key to OFF duringdisc reading. This is not a malfunction.
• The following discs take a longer time to start playback.– a disc recorded with complicated tree structure.– a disc recorded in Multi Session.– a disc to which data can be added.We recommend that you make only one or two trees for each disc.
• Depending on the condition of the disc, it may not play back. Fordetails, please refer to “Notes on discs.”
• Maximum folder number in a disc: 255* (including root folder andempty folders)
• Maximum file number in a disc: 511** Maximum number of files and folders: 512
When a file/folder name contains many characters, this numbermay become less than 512.
Cautions when playing a disc that is recorded in Multi Session• When the first track of the first session is audio CD data: Non-music data
information (track number, time, etc.) is displayed with no sound.• When the first track of the first session is not audio CD data:
– Audio CD data is played back normally; other data is played back withno sound. (MP3 file(s) cannot be played back.)
– If no MP3 file is in the disc, “NO Music” is displayed and nothing isplayed back. (Audio CD data is not recognized.)
Note on character codesCharacter codes vary depending on the master unit.For details, refer to the operating instructions for the master unit.
Note on display of playing timeIn the following cases, elapsed playing time may not be displayedaccurately.– when an MP3 file of VBR (variable bit rate) is played.– during fast-forward/reverse.Tip• To specify a desired playback order, before the folder or file
name, input the order by number (e.g., “01,” “02”), then recordcontents onto a disc. (The order differs depending on the writingsoftware.)
• A disc/album/track name or track number that is over 99 may notbe displayed accurately when this unit is connected to a masterunit that does not support MP3. A master unit that supports MP3is recommended.
About ID3 tag version 2Although not a malfunction, the following occurs whenan MP3 file containing ID3 tag ver.2 is played:– When skipping a portion of ID3 tag ver.2 (at the
beginning of the track), sound is not output.Skip time changes depending ID3 tag ver.2 capacity.Example: At 64 kbytes, it is about 2 seconds(with RealJukebox).
– The displayed elapsed playing time when skipping aportion of ID3 tag ver.2 is inaccurate.For MP3 files of a bit rate other than 128 kbps, time isnot displayed accurately during playback.
– When an MP3 file is created with MP3 conversionsoftware (ex. RealJukebox*), ID3 tag ver.2 willautomatically be written.* “RealJukebox is a registered trademark of
RealNetworks, Inc.”As of December, 2001
4
CDX-565MXRF
Q1 What is MP3?MP3 (MPEG Audio Layer3) is a standardfor compressing audio parts of MovingPictures Experts Group (MPEG).The special feature of MP3 is that the musicdata is compressed to about 1/10 of itsoriginal size while retaining the samesound quality as a CD or an MD.Compared with an audio disc (maximum74 minutes running time), MP3 lets youcompress about 10 audio discs or 160 four-minute songs into a CD-R/RW of 650MB.Note
Recorded music is limited to private use only. Useof music beyond this limit requires the permissionof the copyright holders. Copyright law prohibitscopying, distributing, or delivering all or part ofthe contents.
Q2 What kind of MP3 files can beplayed back?MP3 files in CD-ROMs, CD-Rs, and CD-RWs can be played.Pay attention to the following points whencreating MP3 data CDs using yourcomputer, CD-R/RW drive, writingsoftware, or MP3 file.• The file must be in the ISO 9660 level 1 or
level 2 format, or Joliet or Romeo in theISO 9660 expansion format.A folder name or a file name with theformat other than ISO 9660 level 1 maynot be displayed correctly. Whencreating MP3 data CDs, the format of ISO9660 level 1 is recommended.
• When naming, be sure to add the fileextension “.MP3” to the MP3 file name.The unit cannot recognize an MP3 filewithout the extension “.MP3,” or a filethat is not MP3 format, even with theextension “.MP3.”
Q3 Is there maximum number offolders or files to play?Pay attention to the maximum numbersmentioned below.• Maximum folder number in a disc: 255*
(including root folder and empty folders)• Maximum file number in a disc: 511*
* Maximum number of files and folders:512When a file/folder name containsmany characters, this number maybecome less than 512.
• The maximum number of trees whichcan be played is 8.
The unit allows you to change the folders,to play just the files in your favorite folderrepeatedly, or to play files randomly, createfolders according to artist name or album,and put related MP3 files into folders to usethe unit as a CD changer.
Q4 Can the unit play a data CD withfolder levels?The unit can play a data CD with folderlevels.
Q5 Is there any restriction about thebit rate regarding playback ofMP3 files?There is no specific restriction, but a bit rateof more than 128kbps is recommendedfrom the perspective of sound quality. Theunit also supports VBR (Variable Bit Rate).Note
Elapsed playing time may not be displayedaccurately during cue/reverse.
Q6 Does the unit support a disk of80 minutes running time (700MB data capacity)?The unit supports a disk of 80 minutesrunning time (700 MB data capacity).
Q7 Can the unit play a CD-R/RWcontaining both music CD data(CD-DA) and MP3 file data?The first identified file or data will beplayed back.
Q8 Can the unit play a disc to whichdata can be added (non-finalizeddisc)?The unit can play a non-finalized disc.
Q9 Can the unit play a Multi Sessiondisc?The unit can play a Multi Session disc. Fordetails, refer to the operating instructions.
Q10 Does the unit support Emphasis?The unit does not support Emphasis.
Q11 What is the sampling ratesupporting the unit?The unit is supported from 16kHz to48kHZ.
Q12 Does the unit support the playlist of m3u?The unit does not support the play list ofm3u.
Q13 Does the unit support ID3-Tag?The unit supports ID3 tag ver.1.Pay attention to the following points aboutID3 tag ver.2.
Q14 Is a file name/a folder name ofMP3 different from the namewhen creating a data CD (thename displayed on yourcomputer)?On this unit, a file name/a folder name isdisplayed as below.• A file name/a folder name can be
displayed up to 8 characters.A 9th or later character cannot bedisplayed or scrolled.
• A folder name or a file name in a formatother than ISO 9660 level 1 may not bedisplayed correctly. The file name shouldonly use one byte uppercase, one bytenumeric characters, or an underscore(“__”). It should also be no more than 8characters long, and with no more thanthree characters in the extension.
• Japanese phonetic symbols/ Chinesecharacters cannot be displayed.Only one byte uppercase (A-Z), one bytenumeric character (0-9), and one bytesymbol (“_”, “.”, “<”, “>”, “/”, “+”, “*”)can be displayed. One byte lowercase (a-z) is changed to an uppercase character,and any other characters are displayed as“*”.
Q15 MP3 files recorded onto a CD-R/RW cannot be played.This may happen in following cases.• The recording method onto CD-R/RW is
the packet write method.• The extension file is not an “.MP3.”• The file data is not MP3 format.• Some recording condition (omission of
data, etc.) or some disc condition (dirt,crack, curving, etc.) may cause inabilityto playback an MP3 file.
Q16 It takes some time to startplayback of MP3 file.The unit reads the disc information (thenumber of folders and files, or the locationof the data) before playback of MP3 file. Itmay take more time to start playback of adisc with many trees.Please refer to the instruction manual fordetails.
Q17 Playback skipping and noplayback occur.Recording condition onto CD-R/RW(omission of data, etc.) or disc condition(dirt, crack, curving, etc.) may causeplayback skipping or no playback.
Q18 Can WAVE files be played backon this unit?WAVE files cannot be played back on thisunit.
Q19 Can other compressed formats,such as ATRAC3, be played backon the unit?Only MP3 can be played back on the unit.
MPEG1 48kHz 44.1kHz 32kHz
MPEG2 24kHz 22.05kHz 16kHz
About ID3 tag version 2Although not a malfunction, the following occurswhen an MP3 file containing ID3 tag ver.2 isplayed:– When skipping a portion of ID3 tag ver.2 (at the
beginning of the track), sound is not output. Skiptime changes depending ID3 tag ver.2 capacity.Example: At 64 kbytes, it is about 2 seconds(with RealJukebox).
– The displayed elapsed playing time when skippinga portion of ID3 tag ver.2 is inaccurate.For MP3 files of a bit rate other than 128 kbps, timeis not displayed accurately during playback.
– When an MP3 file is created with MP3 conversionsoftware (ex. RealJukebox*), ID3 tag ver.2 willautomatically be written.* “RealJukebox is a registered trademark of
RealNetworks, Inc.”As of December, 2001
011TRACK.MP3
020TRACK.MP3
091TRACK.MP3
100TRACK.MP3
ROOT
01_ALBUM
02_ALBUM
10_ALBUM
: Folder
: MP3 file
001TRACK.MP3002TRACK.MP3
...
010TRACK.MP3
......
FAQ- about MP3 Audio File
5
CDX-565MXRF
TABLE OF CONTENTS
SERVICING NOTES .......................................................... 2
1. GENERALLocation and function of Controls .................................. 6Installation ....................................................................... 9Connections ..................................................................... 10
2. DISASSEMBLY2-1. Disassembly Flow ........................................................... 112-2. Case (Upper. T), Front Panel Assy ................................. 122-3. Mechanism Deck (MG-251B-137) ................................. 122-4. FM Board ........................................................................ 132-5. MAIN Board, Slide Variable Resistor
(Elevator Height Sensor) (RV202) ................................. 132-6. ELJ Motor Assy (Elevator) (M104) ................................ 142-7. Escutcheon (T) ................................................................ 142-8. Chassis (U.S) Sub Assy .................................................. 152-9. Chassis Assy .................................................................... 152-10. RF Board ......................................................................... 162-11. Sled Motor Assy (251) (M101),
Optical Pick-up (KSS-720A) .......................................... 162-12. LSW Board, Spindle Motor (S) Sub Assy (M102) ........ 172-13. ELJ Motor Assy (Chucking) (M103) ............................. 17
3. ASSEMBLY3-1. Assembly Flow ................................................................ 183-2. Optical Pick-up Complete Assy ...................................... 183-3. Gear (Lomini)/(Load 1) Assy ......................................... 193-4. Operation Check ............................................................. 19
4. MECHANICAL ADJUSTMENT .......................... 20
5. ELECTRICAL CHECK .......................................... 21
6. DIAGRAMS6-1. Block Diagram – SERVO Section – .............................. 226-2. Block Diagram – MAIN Section (1/2) – ....................... 236-3. Block Diagram – MAIN Section (2/2) – ....................... 246-4. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 256-5. Printed Wiring Boards – RF/LSW Boards – ................. 266-6. Schematic Diagram – RF/LSW Boards – ...................... 276-7. Printed Wiring Boards
– MAIN Board (Component Side) – .............................. 286-8. Printed Wiring Boards
– MAIN (Conductor Side)/EJECT Boards – .................. 296-9. Schematic Diagram – MAIN Board (1/3) – .................. 306-10. Schematic Diagram
– MAIN (2/3)/EJECT Boards – ...................................... 316-11. Schematic Diagram – MAIN Board (3/3) – .................. 326-12. Printed Wiring Boards – FM Board – ............................ 346-13. Schematic Diagram – FM Board – ................................. 356-14. IC Pin Function Description ........................................... 40
7. EXPLODED VIEWS7-1. General Section-1 ............................................................ 437-2. General Section-2 ............................................................ 447-3. Mechanism Deck Section-1 (MG-251B-137) ................ 457-4. Mechanism Deck Section-2 (MG-251B-137) ................ 467-5. Mechanism Deck Section-3 (MG-251B-137) ................ 477-6. Mechanism Deck Section-4 (MG-251B-137) ................ 48
8. ELECTRICAL PARTS LIST ............................... 49
6
CDX-565MXRFSECTION 1GENERAL
This section is extracted frominstruction manual.
+ side upCôté + vers le haut
c
Installing the batteryReplace the battery with a new CR2025 lithium battery. Use of any another battery may present a risk of fire orexplosion.
Installation de la pileRemplacez la pile par une nouvelle pile au lithium CR2025. L’utilisation de tout autre type de pile peut poser unrisque d’incendie ou d’explosion.
Lithium battery lifeWhen the battery becomes weak, you will not be able to operate the unit with the wireless remote.Battery life is approx. six months depending on the conditions of use.
WARNINGBattery may explode if mistreated.Do not recharge, disassemble or dispose of in fire.
Notes on the lithium battery• Keep the lithium battery out of the reach of children.
Should the battery be swallowed, immediately consult a doctor.• Wipe the battery with a dry cloth to assure a good contact.• Be sure to observe the correct polarity when installing the battery.• Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur.
Autonomie de la pile au lithiumLorsque les piles s’épuisent, il ne vous sera plus possible de commander l’appareil à l’aide de la télécommandesans fil.L’autonomie de la pile est d’environ six mois suivant les conditions d’utilisation.
ATTENTIONUtilisée de façon incorrecte, la pile peut exploser.Ne pas la recharger, la démonter ni la jeter au feu.
Remarques sur la pile au lithium• Gardez les piles au lithium hors de la portée des enfants.
En cas d’ingestion, consultez immédiatement un médecin.• Essuyez la pile à l’aide d’un chiffon sec de façon à assurer un bon contact.• Respectez la polarité de la pile lorsque vous l’installez.• Ne saisissez pas la pile à l’aide d’une pince métallique, sinon vous risquez de provoquer un court-circuit.
DISCREP SHUF
ALBM ALBM
ENTER DSPL SCRL
LIST
DISC +
10TRACK
D-BASSOFF
DISCREP SHUF
ALBM ALBM
ENTER DSPL SCRL
LIST
DISC +
DISCREP SHUF
ALBM ALBM
ENTER DSPL SCRL
LIST
DISC +
Location and function of controls
Wired remote (RM-X83RF)Télécommande à fil (RM-X83RF)
Wireless remote (RM-X84RF)Télécommande sans fil (RM-X84RF)
1Molette AMS (détecteur automatique demusique)/ENTER
2 Récepteur de télécommande sans fil IR3 Touche LIST4 Touche u (lecture/pause)
Si vous appuyez sur cette touche en cours delecture CD, le CD passe en mode de pause. Si vousappuyez de nouveau sur cette touche, la lectureCD reprend.
5 Touche OFF6 Indicateur DISC/ALBM (numéro de
disque ou d’album)7 Indicateur TRACK (numéro de plage)8 Indication MIN (minute)9 Indication SEC (seconde)0 Indicateur de fichier MP3
Disponible uniquement lorsqu’un disquecomportant des fichiers MP3 est sélectionné.
qa Indicateur d’étiquette ID3Disponible uniquement lors de la lecture d’unfichier MP3.
qs Indication D-BASSqd Indication REP (répétition de la lecture)qf Indication SHUF (lecture aléatoire)qg Touches –/+qh Touche DSPL/SCRL (changement
d’indicateur/défilement du nom)
1AMS (Automatic Music Sensor)/ENTERdial
2 Infrared receptor for the wirelessremote
3LIST button4u (play/pause) button
If pressed during CD playback, the CD will pause.If pressed again, CD playback will continue.
5OFF button6DISC/ALBM (disc number/album number)
indication7TRACK (track number) indication8MIN (minute) indication9SEC (second) indication0MP3 file indication
Available only when a disc with MP3 files isselected.
qa ID3 tag indicationAvailable only when an MP3 file is played.
qsD-BASS indicationqdREP (repeat play) indicationqfSHUF (shuffle play) indicationqg –/+ buttonsqhDSPL/SCRL (indication change/name
scroll) button
AMS functionKeep rotating the AMS/ENTER dial until a desired track isselected.Next track: Rotate the AMS/ENTER dial towards > .Previous track: Rotate the AMS/ENTER dial towards ..While the first/last track on the disc is playing, if the AMS/ENTER dial is rotated, playback skips to the last/first track ofthe disc.
Using on the wireless remotePress AMS/MANU m ./> M to skip/select a track.
Manual search function (Only for the wirelessremote)Keep pressing AMS/MANU m ./> M until adesired point of the track is selected.The elapsed playing time of the track will be shown in thedisplay window during manual search.“ ” or “ ” indicates that the disc has reachedthe beginning/end of the track. It is not possible to reverse/fast-forward at this point.
Disc select function
1 Press (LIST).The disc name during playback will flash.“MP3 DISC” will be displayed if a disc with an MP3 file isselected.
2 Rotate the AMS/ENTER dial to select a desired disc.
3 Press the AMS/ENTER dial to start playback.
NotesThe following indications may be displayed in the following cases.• “NO DISC”: No disc is inserted in the CD changer.• “NO NAME”: No disc name is available.• “NOT READ”: The disc information cannot be read.
Using on the wireless remote
1 Press (LIST).
2 Press / to select a desired disc.
3 Press (ENTER) to start.Also, you can press / to select a disc.The next/previous disc will be selected by each press.
Notes• The display window will be back to normal without an
operation for 5 seconds during the disc select function.• The disc select function is unavailable during “Changing the
transmitting frequency” or “Changing the output level”procedure.
TipPress (LIST) to cancel the disc select function before step 3.
Nomenclature
Fonction AMSTournez la molette AMS/ENTER jusqu’à ce que vous ayezsélectionné la plage souhaitée.Plage suivante : Tournez la molette AMS/ENTER vers > .Plage précédente : Tournez la molette AMS/ENTER vers ..Pendant que la première ou la dernière plage du disque est encours de lecture, si vous tournez la molette AMS/ENTER, lalecture passe à la première ou à la dernière plage du disque.
Utilisation de la télécommande sans filAppuyez sur AMS/MANU m ./> M pour sauter ousélectionner une plage.
Fonction de recherche manuelle (Télécommandesans fil uniquement)Maintenez enfoncée AMS/MANU m ./> M jusqu’àce que vous ayez sélectionné le point souhaité de la plage.Le temps de lecture écoulé de la plage est indiqué dans lafenêtre d’affichage en cours de recherche manuelle.“ ” ou “ ” indique que le disque a atteint ledébut ou la fin de la plage. À ce point, il n’est pas possible dereculer ou d’avancer rapidement.
Fonction de sélection de disque
1 Appuyez sur (LIST).Le nom du disque clignote en cours de lecture.“MP3 DISC” s’affiche si un disque contenant un fichierMP3 est sélectionné.
2 Faites tourner la molette AMS/ENTER poursélectionner le disque souhaité.
3 Appuyez sur la molette AMS/ENTER pour lancer lalecture.
RemarquesLes indications ci-dessous peuvent s’afficher dans les cas suivants.• “NO DISC” : Aucun disque n’a été inséré dans le changeur CD.• “NO NAME” : Aucun nom de disque n’est disponible.• “NOT READ” : Impossible de lire les informations du disque.
Utilisation de la télécommande sans fil
1 Appuyez sur (LIST).
2 Appuyez sur / pour sélectionner le disquesouhaité.
3 Appuyez sur (ENTER) pour commencer.Vous pouvez également appuyer sur /pour sélectionner un disque.Chaque pression permet de sélectionner le disque suivantou précédent.
Remarques• Pendant que la fonction de sélection de disque est activée, la
fenêtre d’affichage revient à l’affichage normal si aucuneopération n’est effectuée pendant cinq secondes.
• La fonction de sélection de disque n’est pas disponible pendantles procédures de changement de fréquence de transmission oude changement de niveau de sortie.
ConseilPour désactiver la fonction de sélection de disque avant l’étape 3,appuyez sur (LIST).
qjALBM –/+ (album select) buttonsSkips to the next/previous album. Note that if thelast album is playing and the ALBM + button ispressed, playback loops back to the first album. Orif the first album is playing, and the ALBM –button is pressed, playback loops to the last album.Available only when an MP3 file is played.
qkAMS/MANU (Automatic Music Sensor/manual search) buttons
qlREP (repeat play) buttonw;ENTER buttonwaDISC +/– buttonswsSHUF (shuffle play) buttonwdD-BASS buttonwf10 TRACK +/– buttons
By pressing the 10 TRACK + or – buttons, the unitskips forwards or backwards 10 tracks (eitherwithin the current album, or into the next/previous album (still counting 10 tracks),depending on the number of tracks in the currentalbum). Note that if any of last 10 tracks of the discis playing and the 10 TRACK + button is pressed,playback loops back to the beginning of the discand continues counting to make a 10-track skip. Orif any of first 10 tracks of the disc is playing, andthe 10 TRACK – button is pressed, playback loopsback to the end of the disc and continues countingto make a 10-track skip.
(Wired remote) (Wireless remote)
(Wired remote) (Wireless remote)
qjTouches ALBM –/+ (sélection d’album)Permettent de passer à l’album précédent ousuivant. Notez que si le dernier album est en coursde lecture et que la touche ALBM + est enfoncée, lalecture revient au premier album. De même, si lepremier album est en cours de lecture et que latouche ALBM – est enfoncée, la lecture revient audernier album.Disponibles uniquement lors de la lecture d’unfichier MP3.
qkTouches AMS/MANU (détecteurautomatique de musique/recherchemanuelle)
qlTouche REP (lecture répétée)w;Touche ENTERwaTouches DISC +/–wsTouche SHUF (lecture aléatoire)wdTouche D-BASSwfTouches 10 TRACK +/–
Lorsque vous appuyez sur la touche 10 TRACK +ou –, l’appareil saute dix plages vers l’avant ouvers l’arrière (soit dans l’album en cours, soit dansl’album suivant ou précédent, dix plages à la fois,selon le nombre de plages de l’album en cours).Notez que si l’une des dix dernières plages dudisque est en cours de lecture et que la touche 10TRACK + est enfoncée, la lecture revient au débutdu disque et continue à sauter des plages jusqu’àun total de dix plages. Notez que si l’une des dixpremières plages du disque est en cours de lectureet que la touche 10 TRACK – est enfoncée, lalecture passe à la fin du disque et continue à sauterdes plages jusqu’à un total de dix plages.
(Télécommande sans fil)(Télécommande à fil)
3
1
2 3 4 5
0 qa qs qd
6 7 9
qf
qg
qh
qj
qk
4
ql
5
w;
wa
ws
wd
wf
DISCREP SHUF
ALBM ALBM
ENTER DSPL SCRL
LIST
DISC +
DISCREP SHUF
ALBM ALBM
ENTER DSPL SCRL
LIST
DISC +
(Télécommande sans fil)(Télécommande à fil)
8
7
CDX-565MXRF
Resetting the unitBefore operating the unit for the first time or after replacing the car battery, you must reset the unit.Press the reset button with a pointed object, such as a ball-point pen, etc.
Réinitialisation de l’appareilAvant la première mise en service de cet appareil ou après avoir remplacé la batterie de la voiture, vous devezréinitialiser l’appareil.Appuyez sur la touche de réinitialisation à l’aide d’un objet pointu comme un stylo à bille, etc.
Listening to a CD1 Turn on the FM tuner of your car audio.
2 Tune in the selected transmitting frequency*with the FM tuner of your car audio.* The frequency of the unit is set to 88.3 MHz at the
factory.
You can change the frequency. (See “Changing thetransmitting frequency” below. )
3 Press u.CD playback starts.
4 Adjust the volume with the volume controlon your car audio.All the tracks play from the beginning.
Stopping CD playPress (OFF).
Notes• When CD playback stops, you may hear some noise
from the speakers. To prevent this from happening,turn the volume of your car audio down beforestopping CD playback.
• If you turn off the ignition switch of your car withoutstopping CD playback, it will automatically resume CDplayback from where it was stopped when you turn onthe ignition switch again.
• The unit cannot be turned on with the wirelessremote. Press u on the wired remote to turn on theunit.
Listening to the radio or a tapeBe sure to stop CD playback before you start listeningto the radio or a tape.
NoteBe sure to stop CD playback, otherwise there may besome interference with radio reception.
Playing tracks in random order— Shuffle Play (Only for the wireless remote)You can select:• SHUF-ALBM* ( ) — to play the tracks on the
current album in random order.• SHUF-DISC ( ) — to play the tracks on the
current disc in random order.• SHUF-CHGR ( ) — to play all the discs in
random order.
* Available only for MP3 files.
During playback, press (SHUF) repeatedlyuntil the desired setting appears in thedisplay.
“SHUF” indicator is displayed.
Shuffle Play starts.
To return to normal play mode, select “SHUF-OFF.”
Playing tracks repeatedly— Repeat Play (Only for the wireless remote)You can select:• REP-TRACK ( ) — to repeat a track.• REP-ALBM* ( ) — to repeat an album.• REP-DISC ( ) — to repeat a disc.
* Available only for MP3 files.
During playback, press (REP) repeatedlyuntil the desired setting appears in thedisplay.
“REP” indicator is displayed.
Repeat Play starts.
To return to normal play mode, select “REP-OFF.”
Display items(Only for the wireless remote)Press (DSPL) to select the following items.DISC/ALBUM*1 number
Displayable items• Track number/Elapsed playing time• Disc name*2/Artist name*3
• Album (folder) name*1
• Track (file) name*1 *2
• ID3 tag*1
*1 Only for MP3 files.Only track name/artist name/album name in ID3 tag isdisplayed.If there is no ID3 tag, “NO ID3” will be displayed for amoment followed by Track number/Elapsed playingtime.
*2 If there is no disc name or track name, “NO NAME”will be displayed for a moment followed by Tracknumber/Elapsed playing time.
*3 Only for CD TEXT discs with the artist name.
Notes• Disc name, artist name, and track title can be displayed
with up to 8 characters.• Some characters cannot be displayed.• This unit cannot display the artist name for each track
of a CD TEXT disc.
Notes on MP3• ID3 tag applies only to version 1.• Some characters cannot be displayed. Characters and
signs which cannot be displayed appear as“ *.”The maximum number of characters for album (folder)names/track (file) names that can be displayed is 64each. ID3 tag is up to 30 characters.
• In the following cases, elapsed playing time may notbe displayed accurately.— when an MP3 file of VBR (variable bit rate) is
played.— during fast-forward/reverse.
A display item that exceeds 8 characters will bescrolled automatically. Press (DSPL) for 2 seconds forfurther scrolling.
Boosting the bass sound— D-bass (Only for the wireless remote)You can enjoy a clear and powerful bass sound. TheD-bass function boosts the low frequency signal andhigh frequency signal with a sharper curve thanconventional bass boost.You can hear the bass line more clearly even while thevocal volume remains the same. You can emphasizeand adjust the bass sound easily with the (D-BASS)button.
0dB
D-BASS 2
D-BASS 1 D.BASS-2
Adjusting the bass curve
Press (D-BASS) repeatedly to select the desiredbass curve.As the D-BASS number increases so does theeffect.
To cancel the D-bass function, select “D-BASS OFF.”
Notes• Setting the output level from 4 to 5 while using the
D-bass function, the amount of bass boost decreases toavoid distortion; however, it’s not a malfunction.Adjust the volume with your car audio.
• Selecting D-BASS 2, a distortion may occur dependingon your CD.Should this occur, select D-BASS or turn down theoutput level.
Changing the transmittingfrequencyBecause this unit processes CD playback soundthrough an FM tuner, there may be interference noiseduring CD playback. In such a case, change thefrequency of the modulated RF signal transmittedfrom the unit. The initial setting is 88.3 MHz.
1 Press the AMS/ENTER dial for two secondsuntil frequency appears.
2 Rotate the AMS/ENTER dial repeatedly toselect the frequency.Each time you rotate the AMS/ENTER dial, thefrequencies change as follows:
Right: 88.3 MHz t 88.5 MHz t 88.7 MHz t
88.9 MHz t 89.1 MHz t 89.3 MHz t
89.5 MHz t 89.7 MHz t 89.9 MHz t
88.3 MHzLeft: 88.3 MHz t 89.9 MHz t 89.7 MHz t
89.5 MHz t 89.3 MHz t 89.1 MHz t
88.9 MHz t 88.7 MHz t 88.5 MHz t
88.3 MHz
3 Press the AMS/ENTER dial for two seconds.
Using on the wireless remote
1 Press (ENTER) for two seconds untilfrequency appears.
2 Press or repeatedly to select thefrequency.
3 Press (ENTER) for two seconds.
Notes• When you change the transmitting frequency on the
unit, be sure to tune your FM tuner to the newlyselected one.
• Press u on the wired remote before changing thefrequency if the power to the unit is turned off.
Changing the output levelYou can select the output level from the unit.Normally the unit is used at the initial output level;change the level if necessary.
1 Press the AMS/ENTER dial for two secondsuntil frequency appears.
2 Press the AMS/ENTER dial momentarily.
Initial setting
3 Rotate the AMS/ENTER dial repeatedly toselect the output level.To increase the output level
Right :
To decrease the output level
Left :
4 Press the AMS/ENTER dial for two seconds.
Using on the wireless remote
1 Press (ENTER) for two seconds.
2 Press (ENTER) again momentarily.
3 Press or to select the output level.
4 Press (ENTER) for two seconds.
NoteWhen you select level 4 or 5, the CD playback sound maybe distorted or you may hear some noise. In such a case,select a lower output level on the unit and turn downthe overall volume on your car audio.
Reset button Touche de réinitialisation
Renforcement des graves— D-bass (Télécommande sans fil uniquement)Vous pouvez exploiter des graves claires etpuissantes. La fonction D-bass renforce les signaux debasse fréquence et les signaux de haute fréquence avecune courbe plus tendue qu’une fonctiond’accentuation classique.Vous entendez plus distinctement les graves, même sile volume de la partie vocale reste au même niveau.Vous pouvez renforcer et ajuster les graves à l’aide dela touche (D-BASS).
0dB
D-BASS 2
D-BASS 1 D.BASS-2
Réglage de la courbe des graves
Appuyez plusieurs fois de suite sur (D-BASS) poursélectionner la courbe des graves voulue.L’effet s’intensifie à mesure que la valeur D-BASSaugmente.
Pour annuler la fonction D-bass, sélectionnez“D-BASS OFF”.
Remarques• Si vous augmentez le niveau d’écoute de 4 à 5 alors
que vous utilisez la fonction D-bass, le niveau desbasses diminue pour éviter une déformation du son ; ilne s’agit en aucun cas d’un dysfonctionnement.Réglez le volume avec votre autoradio.
• Si vous sélectionnez D-BASS 2, une déformation du sonpeut se produire selon votre CD.Si c’était le cas, sélectionnez D-BASS ou baissez leniveau d’écoute.
Changement de la fréquence detransmissionComme cet appareil traite le son de lecture CD via unsyntoniseur FM, il se peut qu’il y ait des interférencesdurant la lecture du CD. En pareil cas, changez lafréquence du signal RF modulé transmis parl’appareil. Le réglage initial est de 88,3 MHz.
1 Appuyez sur la molette AMS/ENTER pendantdeux secondes jusqu’à ce que la fréquences’affiche.
2 Faites tourner la molette AMS/ENTER àplusieurs reprises pour sélectionner lafréquence.À chaque rotation de la commande AMS/ENTER,la fréquence change comme suit :
Droite : 88.3 MHz t 88.5 MHz t 88.7 MHz t
88.9 MHz t 89.1 MHz t 89.3 MHz t
89.5 MHz t 89.7 MHz t 89.9 MHz t
88.3 MHzGauche : 88.3 MHz t 89.9 MHz t 89.7 MHz t
89.5 MHz t 89.3 MHz t 89.1 MHz t
88.9 MHz t 88.7 MHz t 88.5 MHz t
88.3 MHz
3 Appuyez sur la molette AMS/ENTER pendantdeux secondes.
Utilisation de la télécommande sans fil
1 Appuyez sur (ENTER) pendant deuxsecondes jusqu’à ce que la fréquenceapparaisse.
2 Appuyez plusieurs fois de suite sur ou pour sélectionner la fréquence.
3 Appuyez sur (ENTER) pendant deuxsecondes.
Remarques• Si vous changez la fréquence de transmission de
l’appareil, n’oubliez pas de syntoniser votresyntoniseur FM sur la nouvelle fréquence sélectionnée.
• Appuyez sur la touche u de la télécommande filaireavant de changer la fréquence si l’appareil n’est passous tension.
Changement du niveau de sortieVous pouvez sélectionner le niveau de sortie del’appareil. En principe, l’appareil est utilisé au niveaude sortie initial ; changez le niveau si nécessaire.
1 Appuyez sur la molette AMS/ENTER pendantdeux secondes jusqu’à ce que la fréquences’affiche.
2 Appuyez brièvement sur la molette AMS/ENTER.
Réglage initial
3 Faites tourner la molette AMS/ENTER àplusieurs reprises pour sélectionner le niveaude sortie.
Pour diminuer le niveau de sortie
Droite :
Pour augmenter le niveau de sortie
Gauche :
4 Appuyez sur la molette AMS/ENTER pendantdeux.
Utilisation de la télécommande sans fil
1 Appuyez sur (ENTER) pendant deuxsecondes.
2 Appuyez de nouveau brièvement sur(ENTER).
3 Appuyez sur ou pour sélectionner leniveau de sortie.
4 Appuyez sur (ENTER) pendant deuxsecondes.
RemarqueSi vous sélectionnez le niveau 4 ou 5, le son de lectureCD peut comporter des distorsions ou des parasites. Enpareil cas, sélectionnez un niveau de sortie inférieure etbaissez le volume de votre autoradio.
Lecture d’un CD1 Allumez le syntoniseur FM de votre
autoradio.
2 Accordez la fréquence de transmission*sélectionnée au moyen du syntoniseur FMde votre autoradio.* La fréquence de l’appareil est réglée par défaut sur
88,3 MHz.
Vous pouvez modifier la fréquence. (Voir“Changement de la fréquence de transmission”, ci-dessous.)
3 Appuyez sur u.La lecture du CD démarre.
4 Ajustez le volume avec la commande devolume de votre autoradio.Toutes les plages sont reproduites à partir dudébut.
Pour arrêter la lecture d’un CDAppuyez sur (OFF).
Remarques• Lorsque vous arrêtez la lecture d’un CD, il se peut que
vous entendiez des parasites dans les haut-parleurs.Pour éviter ce phénomène, baissez le volume de votreautoradio avant d’arrêter la lecture du CD.
• Si vous coupez le contact de votre voiture sans avoirarrêté la lecture du CD, il reprendra automatiquementla lecture du CD à l’endroit où vous l’avez arrêtélorsque vous rétablirez le contact.
• Si vous ne parvenez pas à mettre l’appareil soustension avec la télécommande sans fil, appuyez sur usur la télécommande raccordée pour mettre l’appareilsous tension.
Ecouter la radio ou une cassetteArrêtez la lecture du CD avant d’écouter la radio ouune cassette.
RemarqueSi vous n’arrêtez pas la lecture du CD, des interférencesrisquent de se produire avec la réception radio.
Lecture de plages dans un ordrequelconque— Lecture aléatoire (Télécommande sans filuniquement)Vous pouvez sélectionner :• SHUF-ALBM* ( ) — pour lire les plages de
l’album en cours dans un ordre aléatoire.• SHUF-DISC ( ) — pour reproduire les plages
du disque en cours dans un ordre aléatoire.• SHUF-CHGR ( ) — pour écouter tous les
disques dans un ordre aléatoire.* Disponible uniquement pour les fichiers MP3.
En cours de lecture, appuyez plusieurs foissur (SHUF) jusqu’à ce que le réglagesouhaité apparaisse dans la fenêtred’affichage.
L’indication “SHUF” est affichée.
La lecture aléatoire démarre.
Pour revenir au mode de lecture normale, sélectionnez“SHUF-OFF”.
Lecture de plages répétée— Lecture répétée (Télécommande sans filuniquement)Vous pouvez sélectionner :• REP-TRACK ( ) — pour répéter une plage.• REP-ALBM* ( ) — pour répéter un album.• REP-DISC ( ) — pour répéter un disque.
* Disponible uniquement pour les fichiers MP3.
En cours de lecture, appuyez plusieurs foissur (REP) jusqu’à ce que le réglage souhaitéapparaisse dans la fenêtre d’affichage.
L’indication “REP” est affichée.
La lecture répétée démarre.
Pour revenir au mode de lecture normale, sélectionnez“REP-OFF”.
Rubriques d’affichage(Télécommande sans fil uniquement)Appuyez sur (DSPL) pour sélectionner l’une desrubriques suivantes.Numéro DISC/ALBUM*1
Rubriques affichables• Numéro de plage/Temps de lecture écoulé• Titre du disque*2/Nom de l’artiste*3
• Nom de l’album (dossier)*1
• Nom de la plage (fichier)*1 *2
• Tag ID3*1
*1 Uniquement pour les fichiers MP3.Dans une étiquette ID3, seuls le nom de la plage, del’artiste et de l’album sont affichés.S’il n’y a pas d’étiquette ID3, l’indication “NO ID3”s’affiche brièvement, suivie du numéro de la plage/dutemps de lecture écoulé.
*2 S’il n’y a pas de nom de disque ou de nom de plage,l’indication “NO NAME” s’affiche brièvement, suiviedu numéro de la plage/du temps de lecture écoulé.
*3 Uniquement pour les disques CD TEXT incluant le nomde l’artiste.
Remarques• Le nom du disque, le nom de l’artiste et le titre de la
plage peuvent être affichés avec 8 caractèresmaximum.
• Certains caractères ne peuvent pas être affichés.• Cet appareil ne peut pas afficher le nom de l’artiste
pour chaque plage d’un disque CD TEXT.
Remarques sur le procédé MP3• Le tag ID3 s’applique uniquement à la version 1.• Certains caractères ne peuvent pas être affichés. Les
caractères et signes qui ne peuvent être affichés sontreprésentés par le symbole “*”.Les noms d’albums (dossiers) et de plages (fichiers)peuvent être affichés dans la limite de 64 caractèreschacun. Les noms des étiquettes ID3 peuvent êtreaffichés dans une limite de 30 caractères.
• Dans les cas suivants, la durée de lecture écoulée peutne pas être exacte.— lors de la lecture d’un fichier MP3 débit binaire
variable.— en cours d’avance/de retour rapide.
Une rubrique d’affichage de plus de huit caractèresdéfile automatiquement dans l’affichage. Appuyez sur(DSPL) pendant deux secondes pour continuer à fairedéfiler le texte.
Operation Fonctionnement
8
CDX-565MXRF
Changement du niveau de sortieVous pouvez sélectionner le niveau de sortie del’appareil. En principe, l’appareil est utilisé auniveau de sortie initial ; changez le niveau sinécessaire.1 Appuyez sur la molette AMS/ENTER
pendant deux secondes jusqu’à ce que lafréquence s’affiche.
2 Appuyez brièvement sur la moletteAMS/ENTER.
3 Faites tourner la molette AMS/ENTER àplusieurs reprises pour sélectionner leniveau de sortie.Pour diminuer le niveau de sortie
Pour augmenter le niveau de sortie
4 Appuyez sur la molette AMS/ENTERpendant deux.
Utilisation de la télécommande sans fil1 Appuyez sur (ENTER) pendant deux
secondes.2 Appuyez de nouveau brièvement sur(ENTER).
3 Appuyez sur ou pour sélectionnerle niveau de sortie.
4 Appuyez sur (ENTER) pendant deuxsecondes.
RemarqueSi vous sélectionnez le niveau 4 ou 5, le son de lectureCD peut comporter des distorsions ou des parasites. Enpareil cas, sélectionnez un niveau de sortie inférieureet baissez le volume de votre autoradio.
Changing the transmittingfrequencyBecause this unit processes CD playback soundthrough an FM tuner, there may be interferencenoise during CD playback. In such a case, changethe frequency of the modulated RF signaltransmitted from the unit. The initial setting is88.3 MHz.1 Press the AMS/ENTER dial for two
seconds until frequency appears.2 Rotate the AMS/ENTER dial repeatedly to
select the frequency.Each time you rotate the AMS/ENTER dial,the frequencies change as follows:
Right :88.3 MHz t 88.5 MHz t 88.7 MHzt 88.9 MHz t 89.1 MHz t
89.3 MHz t 89.5 MHz t 89.7 MHzt 89.9 MHz t 88.3 MHz
Left : 88.3 MHz t 89.9 MHz t 89.7 MHzt 89.5 MHz t 89.3 MHz t
89.1 MHz t 88.9 MHz t 88.7 MHzt 88.5 MHz t 88.3 MHz
3 Press the AMS/ENTER dial for twoseconds.
Using on the wireless remote
1 Press (ENTER) for two seconds untilfrequency appears.
2 Press or repeatedly to select thefrequency.
3 Press (ENTER) for two seconds.Notes• When you change the transmitting frequency on the
unit, be sure to tune your FM tuner to the newlyselected one.
• Press u on the wired remote before changing thefrequency if the power of the unit is turned off.
Réglage initial
NoteThe supplied wireless remote (RM-X84RF) can beoperated almost like the wired remote (RM-X83RF).
RemarqueLa télécommande sans fil fournie (RM-X84RF) semanipule pratiquement comme la télécommandefilaire (RM-X83RF).
Changing the output levelYou can select the output level from the unit.Normally the unit is used at the initial outputlevel; change the level if necessary.1 Press the AMS/ENTER dial for two
seconds until frequency appears.2 Press the AMS/ENTER dial momentarily.
3 Rotate the AMS/ENTER dial repeatedly toselect the output level.
To increase the output level
To decrease the output level
4 Press the AMS/ENTER dial for twoseconds.
Using on the wireless remote1 Press (ENTER) for two seconds.2 Press (ENTER) again momentarily.3 Press or to select the output level.4 Press (ENTER) for two seconds.NoteWhen you select level 4 or 5, the CD playback soundmay be distorted or you may hear some noise. In sucha case, select a lower output level on the unit and turndown the overall volume on your car audio.
Left :
Right :
AMS/ENTER dialMolette AMS/ENTER
Initial setting
Wired remote (RM-X83RF)/Télécommande à fil (RM-X83RF)
Changement de la fréquence detransmissionComme cet appareil traite le son de lecture CD viaun syntoniseur FM, il se peut qu’il y ait desinterférences durant la lecture du CD. En pareilcas, changez la fréquence du signal RF modulétransmis par l’appareil. Le réglage initial est de88,3 MHz.1 Appuyez sur la molette AMS/ENTER
pendant deux secondes jusqu’à ce que lafréquence s’affiche.
2 Faites tourner la molette AMS/ENTER àplusieurs reprises pour sélectionner lafréquence.À chaque rotation de la commande AMS/ENTER, la fréquence change comme suit :
Droite : 88.3 MHz t 88.5 MHz t 88.7 MHzt 88.9 MHz t 89.1 MHz t89.3 MHz t 89.5 MHz t 89.7 MHzt 89.9 MHz t 88.3 MHz
Gauche : 88.3 MHz t 89.9 MHz t 89.7 MHzt 89.5 MHz t 89.3 MHz t
89.1 MHz t 88.9 MHz t 88.7 MHzt 88.5 MHz t 88.3 MHz
3 Appuyez sur la molette AMS/ENTERpendant deux secondes.
Utilisation de la télécommande sans fil
1 Appuyez sur (ENTER) pendant deuxsecondes jusqu’à ce que la fréquenceapparaisse.
2 Appuyez plusieurs fois de suite sur ou pour sélectionner la fréquence.
3 Appuyez sur (ENTER) pendant deuxsecondes.
Remarques• Si vous changez la fréquence de transmission de
l’appareil, n’oubliez pas de syntoniser votresyntoniseur FM sur la nouvelle fréquencesélectionnée.
• Appuyez sur la touche u de la télécommandefilaire avant de changer la fréquence si l’appareiln’est pas sous tension.
Gauche :
Droite :
9
CDX-565MXRF
HORIZONTAL
VERTICAL
HORIZONTAL
InstallationInstallation du changeur de CD•Quand vous installez le changeur de CD, veillez à ne pas endommager les câbles ou les instruments qui
se trouvent de l’autre côté.•Les supports 1 offrent deux positions de montage, haut et bas. Utilisez les trous de vissage appropriés
en fonction de vos préférences.
Installation
Horizontal installation Installation horizontale
1
1Vertical installation Installation verticale
Align with the marked position.
Alignez sur le repère.
Align with the marked position.
Alignez sur le repère.
Suspended installation Installation suspendue
1
When the unit is to be installed under the rear tray or in the trunk, observe the following.•Choose the mounting location carefully so that the unit can be installed horizontally.•Make sure the unit does not hinder the action of the torsion bar spring, hinge, etc. of the deck lid.
Si vous comptez installer le changeur de CD sous la plage arrière ou dans le coffre, prenez les précautionssuivantes.• Choisissez soigneusement l’emplacement pour que le changeur soit à l’horizontale.• Assurez-vous que l’appareil n’entrave pas l’action du ressort à barre de torsion, des charnières, etc., du
couvercle de la malle.
Inclined installation Installation inclinée
After installing the unit, align the dials with one of the marks so the arrow comes as close to avertical position as possible.
NoteBe sure to align the left and right dials with the same mark.
RemarqueVeillez à aligner les disques gauche et droite sur le même repère.
Align with the marked position.
Alignez sur le repère.
21
1
2
Installing the wired remoteUse the supplied double-sided adhesive tape 4, and mount the wired remote in a suitable location whereit will not interfere with your driving.
Installation de la télécommande à filUtilisez la bande à double face adhésive fournie 4 pour installer la télécommande à fil dans un endroitqui ne risque pas de gêner la conduite.
4The back of the wired remoteDos de la télécommande à fil
33
3
1
1
2
3
2
1
1
2
32
3
ø 3.5 mm(5/32 in.)ø 3,5 mm(5/32 po.)
2
2
2
Après avoir installé l’appareil, alignez les disques sur l’un des repères afin que la flèche soit aussiproche que possible de la position verticale.
HORIZONTAL
VE
RTIC
AL
HORIZONTAL
VE
RTIC
AL
HO
RIZ
ON
TAL
VERTICAL
How to install the CD changer•When you install the CD changer, be careful not to damage wiring or equipment on the other side of the
mounting surface.•The brackets 1 provide two positions for mounting, high and low. Use the appropriate screw holes
according to your preference.
ø 3.5 mm(5/32 in.)ø 3,5 mm(5/32 po.)
ø 3.5 mm (5/32 in.)ø 3,5 mm (5/32 po.)
10
CDX-565MXRF
ConnectionsCaution•This unit is designed for negative ground 12 V
DC operation only.•Before making connections, turn the car ignition
off to avoid short circuits.•Connect the yellow and red power input leads
only after all other leads have been connected.
Précautions•Cet appareil est uniquement conçu pour
fonctionner sur 12 V CC avec une massenégative.
•Avant d’effectuer les raccordements, coupez lecontact du véhicule pour éviter tout court-circuit.
•Branchez les fils d‘entrée d‘alimentation jaune etrouge seulement après avoir terminé tous lesautres branchements.
• Be sure to connect the red power input lead to thepositive 12 V power terminal which is poweredwhen the ignition switch is in the accessoryposition.
• Run all earth wires to a common earth point.• When finished making all the connections,
press the reset button of the CD chnager. (See“Reset button” below.)
• The use of optical instruments with this productwill increase eye hazard.
•Veillez à raccorder le fil rouge d‘entréed‘alimentation à la borne positive de 12 V qui estalimentée quand la clé de contact est sur laposition accessoire.
•Rassemblez tous les fils de terre en un pointde masse commun.
•Lorsque vous avez terminé toutes lesconnexions, appuyez sur la touche deréinitialisation du changeur de CD. (Voir“Touche de réinitialisation” ci-après.)
•L’utilisation d’instruments optiques avec cetappareil accroît les risques de blessures aux yeux.
Installing the wireless remoteUse the supplied hook and loop fastener 5, and mount the wireless remote in a suitable location where itwill not interfere with your driving.
Installation de la télécommande sans filUtilisez les bandes adhésives 5 pour installer la télécommande sans fil dans un endroit qui ne risque pasde gêner la conduite.
Connexions
Reset buttonAfter the installation and connections are completed, after the batteries have been changed, be sure topress the reset button with a ball-point pen, etc.
Touche de réinitialisationAprès avoir terminé l’installation et les connexions ou remplacé les piles, n’oubliez pas d’appuyer sur latouche de réinitialisation à l’aide d’un stylo à bille, etc.
Reset buttonTouche de réinitialisation
Connection diagram Schéma de connexión
to where it is going to be mountedvers la surface de montage
Remplacement du fusibleSi le fusible saute, vérifiez la connexiond’alimentation et remplacez-le. Si le fusible saute ànouveau quand vous venez de le remplacer, ils’agit peut être d’un mauvais fonctionnementinterne.
Warning
Use a fuse with the specified amperage rating.Use of a higher amperage fuse may cause seriousdamage.
AvertissementUtilisez un fusible de l’ampérage spécifié.L’utilisation d’un fusible d’ampérage supérieurpeut causer de sérieux dommages.
Fuse replacementIf the fuse blows, check the power connection andreplace the fuse. If the fuse blows again afterreplacement, there may be an internal malfunction.
YellowJaune
RedRouge
BlackNoir
Wired RemoteTélécommande à fil
CD changerChangeur de CD
6
Car audioAutoradio
Speaker systemSystème dehaut-parleurs
Antenna connector*Connecteur d‘antenne*
to the +12 V power terminal which is powered when theignition key switch is in the accessory positionBe sure to connect the black earth lead first.
à la borne d’alimentation de +12 V qui est alimentée quandla clé de contact est sur la position accessoireRaccordez d’abord le fil de masse noir.
to a metal point on the carFirst connect the black earth lead, then connect the yellowand red power input leads.
vers un point métallique de la voitureBranchez d’abord le fil de masse noir et, ensuite, les filsd’entrée d’alimentation jaune et rouge.
to the +12 V power terminal which is powered at all timesBe sure to connect the black earth lead first.
à la borne d’alimentation +12 V qui est alimentée enpermanenceRaccordez d’abord le fil de masse noir.
Protection resistorRésistance deprotection
FuseFusible
Relay boxBoîtier de relais
7
from the car antenna*depuis l’antenne de la voiture*
Insert the connector until it locks.Insérez le connecteur jusqu’à cequ’il s’enclenche.
5
* An adaptor (optional) may be necessary for yourcar and car audio system. In such a case, consultyour dealer.
* Un adaptateur (en option) peut s’avérernécessaire suivant votre voiture et votreautoradio. En pareil cas, consultez votrerevendeur.
1 m
5 m
5 m
5.5 m5,5 m
0.5 m0,5 m
AVERTISSEMENT• Branchez le connecteur sur la prise du côté
gauche du changeur de CD. Assurez-vousque l’ergot du connecteur s’adapte dansl’orifice à côté de la prise.
• Après l’avoir branché, tirez légèrement surle connecteur pour vous assurer qu’il estbien enclenché.
WARNING•Plug the connector into the jack on the
left side of the CD changer. Make surethat the catch of the connector issecured in the hole next to the jack.
•After inserting the connector, pull theconnector lightly to make sure that itis locked.
CatchErgot
ConnectorConnecterur
5 m
RM-X83RF
CDX-565MXRF
11
• This set can be disassembled in the order shown below.
SECTION 2DISASSEMBLY
2-1. DISASSEMBLY FLOW
2-2. CASE (UPPER.T), FRONT PANEL ASSY(Page 12)
2-3. MECHANISM DECK(MG-251B-137)(Page 12)
2-4. FM BOARD(Page 13)
2-7. ESCUTCHEON (T)(Page 14)
2-8. CHASSIS (U.S) SUB ASSY(Page 15)
2-5. MAIN BOARD, SLIDE VARIABLE RESISTOR(ELEVATOR HEIGHT SENSOR) (RV202)(Page 13)
2-6. ELJ MOTOR ASSY(ELEVATOR) (M104)(Page 14)
2-9. CHASSIS ASSY(Page 15)
2-10. RF BOARD(Page 16)
2-13. ELJ MOTOR ASSY (CHUCKING) (M103)(Page 17)
2-11. SLED MOTOR ASSY (251) (M101),OPTICAL PICK-UP (KSS-720A)(Page 16)
2-12. LSW BOARD,SPINDLE MOTOR (S) SUB ASSY (M102)(Page 17)
SET
Note 1: The process described in can be performed in any order.
Note 2: Without completing the process described in , the next process can not be performed.
CDX-565MXRF
12
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE (UPPER. T), FRONT PANEL ASSY
3 screw (PTT2.6 × 6)
4 lever (FLT. 838)
3 screw (PTT2.6 × 6)
3 screw (PTT2.6 × 6)
1 screw (PTT2.6 × 6)
1 screw (PTT2.6 × 6)
2 front panel assy
4 lever (FLT. 838)
5 case (upper. T)
2-3. MECHANISM DECK (MG-251B-137)
1 two dampers (T)
1 two dampers (T)3 FM flexible board(CN701)
filament tape
2 tension coil spring (FL)
4 mechanism deck (MG-251B-137)
2 tension coil spring (FL)
CDX-565MXRF
13
2-4. FM BOARD
2-5. MAIN BOARD, SLIDE VARIABLE RESISTOR (ELEVATOR HEIGHT SENSOR) (RV202)
1 screw (BVTT2.6 × 6)
3 cover (FM connector.T)
2 screw (ground)
4 cover (FM)
5 FM board
1 main flexible board(CNJ101) 5 two screws (FP)
5 screw (FP) 6 main board
2 Remove two solders of the elevator motor leads (M104).
2 Remove three solders of the slide variable resistor(RV202). 2 Remove four solders of
the SW board leads.
3 screw (PTT2 × 4)
4 heat sink (T)
8 slide variable resistor(elevator height sensor)(RV202)
7 screw (PTT2 × 4)
CDX-565MXRF
14
2-6. ELJ MOTOR ASSY (ELEVATOR) (M104)
2-7. ESCUTCHEON (T)
1 screw (PTT2 × 4)
2 bracket (EVM.S)
3 ELJ motor assy (elevator) (M104)
2 Remove the claw in the direction of arrow A.
4 Remove the ditch in the direction of arrow B.
A
B
5 Remove the escutcheon (T)in the direction of arrow C.
4 ditch
3 clawC
3 two claws
1 screw (T)
CDX-565MXRF
15
2-8. CHASSIS (U.S) SUB ASSY
2-9. CHASSIS ASSY
1 three screws (PTT2 × 4)
1 screw(PTT2 × 4)
1 two screws (PTT2 × 4)
4 spring (SUT)
2 Remove the edge in the direction of arrow A.
5 chassis (U.S) sub assy
3
A
6 chassis assy
1 Turn the gear (EVD.S) fully in the direction of arrow A.
5 spring (stopper.lower)
4
A
3
2
3
CDX-565MXRF
16
2-10. RF BOARD
2-11. SLED MOTOR ASSY (251) (M101), OPTICAL PICK-UP (KSS-720A)
3 two screws(PS2 × 4)
3 two screws(PS2 × 4)
2 Remove four solders of the LSW board leads and spindle motor leads (M102).
2 Remove two solders of the sled motor leads (M101). 1 OP flexible board (CN102).
4 RF board
1 two precision screws (P2 × 3)
4 Turn shaft (feed) assy in the direction of the arrow, then remove it.
2 sled motor assy (251)(M101)
OP flexible board
adhesive sheet
3 optical pick-up(KSS-720A)
optical pick-up
Note: After connecting OP flexible board, fix it with adhesive sheet to optical pick-up.
CDX-565MXRF
17
2-12. LSW BOARD, SPINDLE MOTOR (S) SUB ASSY (M102)
2-13. ELJ MOTOR ASSY (CHUCKING) (M103)
8 two precision screws(P1.7 × 2.2)
7
3 spring (chucking)
6 retainer (disc)
4 precision screw(P2 × 2.2)
5 bracket (CP)
9 Remove the spindle motor (S) sub assy (M102) in the direction of the arrow.
2 LSW board
1 precision screw(P2 × 2.5)
2 two screws (PTT2 × 4)
3 retainer (CHM)
4 ELJ motor assy(chucking) (M103)
1 Remove two solders of the chucking motor leads (M103).
CDX-565MXRF
18
• This set can be assembled in the order shown below.
SECTION 3ASSEMBLY
3-1. ASSEMBLY FLOW
3-2. OPTICAL PICK-UP COMPLETE ASSY(Page 18)
3-3. GEAR (LOMINI) / (LOAD 1) ASSY(Page 19)
3-4. OPERATION CHECK(Page 19)
3-2. OPTICAL PICK-UP COMPLETE ASSY
chuck plate
1 Move the lever (LOCK 3A) in the direction of arrow A, and return it a little in the direction of arrow B from the position where the chuck plate is moveddown to the lower limit.
A
B
3 stop ring 2.0 (E type)
4 tension spring (DH)
2 optical pick-up complete assyNote: Insert the shaft (A) first.
shaft (A)
CDX-565MXRF
19
3-3. GEAR (LOMINI)/(LOAD 1) ASSY
3-4. OPERATION CHECK
1 Confirm that the slider moves in the direction of arrow C to move downthe chuck plate if the gear (LOAD 1) is rotated in the direction of arrow Aor the chuck plate moves up and the slider moves in the direction of arrowD if the gear is rotated in the direction of arrow B.
gear (LOAD 2)
gear (LOMINI)
markingFig. A
chuck plate
2 Attach the gear (LOMINI) at the position shown in Fig. A.
shaft (rotary prevention C)
1 Move the lever (LOCK 3A)fully in the direction of arrow B to move the chuck plate up.
B
4 stop ring 1.5 (E type)
3 Attach the gear (LOAD 1) assywith its facing inside.
slit
chuck plate
slider
gear (LOAD 1) assy
A B
C
D
20
CDX-565MXRFSECTION 4
MECHANICAL ADJUSTMENT
ELEVATOR HEIGHT (ADDRESS) ADJUSTMENT
Note: This adjustments is necessary when the system controller (IC201),variable resistor (RV201), slider (R), slider (L), or chassis (ELV)was replaced for any repair.
Connection:
Adjustment Method:
Note: Perform following the adjustment by the wired remote commander(RM-X83RF).
1. Load a disc magazine, and place the set vertically as shownbelow.
2. Connect the regulated power supply, and turn the power on.3. Select DISC 5.4. At this time, if the elevator shaft does not position between
comb teeth A and B at addresses 5 and 6 as shown below,adjust the following.
5. Select DISC 5 and DISC 6 alternately, so that the elevator shaftsmoves from address 6 to address 5, or from 5 to 6. At thistime, adjust RV201 on the main board so that the elevator shaftpositions smoothly between comb teeth A and B.
6. Further, place the set horizontally and make same adjustmentas mentioned above.
7. After adjustment at addresses 5 to 6 is finished, check all op-erations from addresses 1 to 10 with the set placed verticallyand horizontally respectively to confirm that the elevator shaftpositions in a range between comb teeth A to B.
power supply(DC 14.4 V)
compact disc changer
wired remote commander(RM-X83RF)
GND+
DISPLAY connector (CN302)
POWER connector (CN303)
RV201
comb tooth at address 6
elevator shaft
comb tooth at address 6
comb tooth at address 5
OK NG
elevator shaft
comb tooth at address 5
A
B
A
B
CDX-565MXRF
2121
SECTION 5ELECTRICAL CHECK
Note:1. This adjustment is performed with the set placed horizontally.2. Power supply voltage: DC14.4 V (more than 3 A).3. Be sure to use the disc “YEDS-18” parts code: 3-702-101-01, but only
when indicated.
Connection:
FOCUS BIAS CHECK
Connection:– RF Board (Component Side) –
Procedure:1. Connect the oscilloscope to TP (RFAC) and TP (VC) on the
RF board.2. Put the set into play mode by loading the disc (YEDS-18).3. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.Note:Clear RF signal waveform means that the shape “ ◊ ” can be clearly distin-guished at the center of the waveform.
When observing the eye pattern, set the oscilloscope to AC rangeand raise the vertical sensitivity so that it may be easily seen.
power supply(DC 14.4 V)
compact disc changer
wired remote commander(RM-X83RF)
GND+
DISPLAY connector (CN302)
POWER connector (CN303)
oscilloscope(AC range)
+– TP (VC)
TP (RFAC)
IC101
RF signal waveform
VOLT/DIV: 200 mVTIME/DIV: 500 ns(10 : 1 probe in use)
level: 1.4 ± 0.3 Vp-p
TRACKING OFFSET CHECK
Connection:– RF Board (Component Side) –
Procedure:1. Connect the oscilloscope to TP (TE) and TP (VC) on the RF
board.2. Put the set into play mode by loading the disc (YEDS-18).3. Rotate the [ AMS ] dial on the wired remote commander,
and check the traverse waveform*.4. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0 V dc, and check this level.* Traverse waveform: This is the tracking error wave form appears
when crossing the track.
. >
oscilloscope(DC range)
+– TP (VC)
TP (TE)
IC101
A
B
0 V
A=B
traverse waveform(100 track jump waveform)
VOLT/DIV: 500 mVTIME/DIV: 2 msCenter: 0 V
Traverse waveform
CDX-565MXRF
2222
6-1. BLOCK DIAGRAM – SERVO Section –
SECTION 6DIAGRAMS
RFACSUMMING
AMP
RFDCSUMMING
AMP
ACSUM
4 3EQ IN
7
8
9
A
B
C
D RW/ROM
28
30
16
18
RFDCO
DC OFST
FE
TEEF
1011
FOCUSERROR
AMP
TRACKINGERROR
AMP
SW
PD
12
2LD
1 APC AMP
RW/ROM
15RFACRFAC
VCARF EQAMP
116,
115
,11
8, 1
17
RF
FE
TE
109
– 10
6, 7
– 5
,3
– 1,
111
9 –
12, 1
5 –
19,
21, 8
2, 3
,24
, 25
523422
RASCASWEOE
113119114120
XRASXCASXWEXOE
VIBRATIONMEMORY
CONTROLLER&
COMPRESSIONEXPANDER
A0 –
A10
A0 – A10
DQ1
– DQ
4 D0 – D3
RFAC
ASYIASYO
71
7374
66 69 68 67
FILO
CLTV
PCO
FILI
ASYMMETRYCORRECTOR
DIGITALPLL
EFMDEMODULATOR
INTE
RNAL
BUS
D/AINTERFACE
ERRORCORRECTOR
32k RAM
1515
159088
86
BCKPCMD
LRCKSELECTOR
DIGITALOUT 1585
DOUT
XTAO
XTAI
CLOCKGENERATOR
1578
1581
WDCK
GFS
152315251524
1526
151415151517
DATACLOKXLAT
SENS
SQSOSQCKSCOR
SUBCODEPROCESSOR
CPUINTERFACE
XRDEXWREXQOK
1591581512
XRDEXWREXQOK
SERVO AUTOSEQUENSOR
SCLK
FOK
XRST
27
35
21
SERVOINTERFACE
45
SSTP
TEFERF
SETEFERF
DC
61606258
OP AMPANALOG SW
A/D CONVERTER
SERV
O DS
P
PWM
GEN
ERAT
OR
5051
4849
4647
43
FFDRFRDR
TFDRTRDR
SFDRSRDR
MDP
MIRRDECTFOK
DIGITALCLV
67
89
1011
1213
54
VO4 +VO4 –
VO3 +VO3 –
VO2 +VO2 –
VO1 +VO1 –
VL0 +VL0 –
VIN4 +VIN4 –
VIN3 +VIN3 –
VIN2 +VIN2 –
FWDREV
3132
2524
2221
12
MOTORDRIVE
MOTORDRIVE
MOTORDRIVE
COILDRIVE
MOTORDRIVECOIL
DRIVE
TRACKING/FOCUS COIL DRIVE,SLED/SPINDLE/CHUCKING
MOTOR DRIVEIC201
A
B
C
D
E
F
I-V A
MP
PD LD
DETECTOR
(TRACKING)
(FOCUS)
2-AXIS DEVICE
OPTICALPICK-UP BLOCK
(KSS-720A)
LASER DIODE
MMM101(SLED)
MMM102(SPINDLE)
MMM103(CHUHCKING)
1588
SW3(LIMIT)
SW1(CHUCKING END DETECT)
SW2(SAVE END DETECT)
ON : When the optical pick-up is inner position
ON : When completion of the disc save operation
ON : When completion of the disc chucking operation
ON : When the optical pick-up is inner position
ON : When completion of the disc save operation
ON : When completion of the disc chucking operation
R/RW SEL
GRSCOR
GFS
CDDATCDCLKCDLAT
SENS
SCOR
XRDEXWREXQOK
SCLK
LIM SW
LOAD SW
SAVE SW
XRST
FOK
SQSOSQCK
90
40
5
1089
7
38
161715
6
98
11
4
8485
LOADFLOADR
9596
99
CD-ROM/RWSELECT SWITCH
Q202
RF AMP OFFSETCONTROL SWITCH
Q102
SIGNAL PATH: CD PLAY
FILTER
DIGITAL SIGNAL PROCESSOR,DIGITAL SERVO PROCESSOR,
D-RAM CONTROLLERIC101
D-RAMIC102
AUTOMATICPOWER
CONTROLQ101
RF AMP,FOCUS/TRACKING ERROR AMP
IC101
6
SYSTEM CONTROLLERIC201 (1/3)
VIN1-B18
VC27 DVC 14VC
CEVC
5963
X10116.9344MHz
A
B
D
BCKSDI
LRCK
XTAL-IN
SDO
100
D201 ETCXRDE
(Page 23)
(Page 23)
(Page 23)
(Page 23)
BCKIPCMDI
LRCKI15159187
15881589D/A
CONVERTERLOW-PASS
FILTER
AOUT115881599
AOUT2102
AIN115881598
AIN2103
LOW-PASSFILTER
LOUT197
LOUT2104
C(Page 23)
L
R
93 94
CDX-565MXRF
2323
9 SDO
12 SDIO
13 BCKIA
14 LRCKIA
62 X163 X0
60 XRDE
B
A
D
E
SDO
SDI
BCK
LRCK
TCXRDE
XTAL-IN
CD-ROM DECODERMP3 DECODER
IC601
IC605
39
REQ
19
STAN
BY
1
RESE
T
5
I2C
SDA
6
I2C
SCL
73
DECI
NT
3
DECS
TBY
2
DECX
RST
80
SDA
81
SCL
IC604
16CE43WR17OE
30 CS15 WE32 OE
20 −
13,
3, 2
, 31,
1,
12, 4
, 11,
7, 1
0
3, 4
, 7, 1
0, 1
1, 1
5,38
− 3
6, 3
4 −
31, 4
1,42
, 45,
44
46, 4
7, 4
9 −
51,
53 −
55
21 −
23,
25 −
29IO
1 −
IO8
A0 −
A16
AD0 −
AD16
IO0 −
IO7
S-RAMIC602
SYSTEM CONTROLLERIC201 (2/3)
SIGNAL PATH: CD PLAY
(Page 22)
(Page 22)
(Page 22)
(Page 22)
OUTPUTCN703
22 LIN
1 RIN
16
PRE-EMPHASIS& LIMITER
PRE-EMPHASIS& LIMITER
MPX
XIN
XOUTOSC
MUTING OSC
BUFFER, AMPQ701, 702
RF AMP
PHASEDETECTOR
PROGRAMCOUNTER
SHIFTREGISTER
5
MPXADJ
18
MUT
FM STEREOTRANSMITTER
IC701
9 11
7
RF IN
PD
RF OUTL. P. F.
RV701TRANSMITTERMODULATIONSENSITIVITY
15
CE
17
DATA
CLK
10 128
11 139
89 88
PLLC
E
87
PLLD
ATA
PLLC
LK
BUS BUFFERIC302 (1/2)
C(Page 22)
L
R
ISOLATORIC401
L. P. F.
L. P. F.
MUTINGQ410, 420
26
MUT
E
X7017.6MHz
14
13
MUTING CONTROLSWITCH
Q402
6-2. BLOCK DIAGRAM – MAIN Section (1/2) –
CDX-565MXRF
2424
3ACC
2B. UP
POWERCN303
91ACCIN
52MCK
ACCESSORYCHECKQ308
50EHS
53VREF
ELVON
RV201
ELEVATOR HEIGHT(ADDRESS)
RV202ELEVATOR HEIGHT
SENSOR
30
+8VREGULATOR
IC304DRIVER +8V
+5VREGULATOR
IC304LCD +5V
BUCHK 92
D306
D301
59
CDON 29EJECT75
SW302(RESET)
+5VREGULATOR
IC305SERVO +5V
SW301
72 MGLK-SW
36 ELVF37 ELVR
SW201MAGAZINE
DETECT
ON : When magazine is set
34
65 EXTAL
63 XTAL
78 KEYACK
39 KEYON
49 KEYIN
97
MOTORDRIVE
IN1IN2
OUT1OUT2
ELEVATORMOTOR DRIVE
IC301
MM104
(ELEVATOR)
X20112.288MHz
KEY ACTIVESWITCH
Q205B. UP+3.3V
34 LCDDATA
33 LCDCLK
35 LCDCE
41 SIRCS
8
5
4
3
7
2
DISPLAYCN302
LCD +5VPOWER ON
SIRCS
LCDCE
LCDCLK
LCDDATA
KEYA/D
SYSTEM CONTROLLERIC201 (3/3)
RES
HIGH VOLTAGEDETECT
Q302
BATTERYCHECK
Q301, 305
RESET SIGNALGENERATOR
IC303
D202
47 ENCODER16
48 ENCODER21
ENCODER2
ENCODER1
6
2
4
5
1
3
BUS BUFFERIC302 (2/2)
D302
B. UP+3.3V
+3.3VREGULATORQ303, 304
28LCDON
+2.5VREGULATOR
IC603
CD-ROM/MP3DECODER
+2.5V
+3.3VREGULATOR
IC306SERVO +3.3V
D203
6-3. BLOCK DIAGRAM – MAIN Section (2/2) –
CDX-565MXRF
2525
6-4. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• f : internal component.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)
Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• % : indicates tolerance.• f : internal component.• C : panel designation.
• A : B+ Line.• H : adjustment for repair.• Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.• Voltages and waveforms are dc with respect to ground in
CD play mode.no mark : CD PLAY
∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-tion tolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.
• Circled numbers refer to waveforms.• Signal path.
J : CD PLAY
Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.
Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce por tant le numérospécifié.
• Circuit Boards Location
EJECT board
FM board
LSW board
RF board
MAIN boardCaution:Pattern face side: Parts on the pattern face side seen from(Conductor Side) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Component Side) the parts face are indicated.
CDX-565MXRF
2626
6-5. PRINTED WIRING BOARDS – RF/LSW Boards – • See page 25 for Circuit Boards Location.
• SemiconductorLocation
Ref. No. Location
IC101 H-6IC201 J-5
Q101 F-7Q102 H-7
C201
C121
C105
SW1CHUKING
END DETECT
SW2SAVE ENDDETECT
CN102
IC201
C102
Q101
TP101
TP102
TP108
TP107
TP104TP103TP105TP106
IC101
C217
C203
C204
C205
C206
C207
C208C202
C106
C209
C109 C104
C122
C107
C111
C101
R201R202
R203R204
R206R205
R207R208
R210R209
R211R212
R214
R213
R218
R219
R220
R222R223
R104
R215
R216
R108
R109
R110
R117
R112
R113
R107
R105
R101
R103
R102
C103
R120
R121
R122
R106
C108
Q102
CNJ101
SW3(LIMIT)
BLU
YEL
YEL
RED
BLK
WHT
1-679-422-
12
(12)
M101(SLED) M
LSW BOARD
M103(CHUKING) M
OPTICALPICK-UPBLOCK
(KSS-720A)
OP FLEXIBLEBOARD
MAIN FLEXIBLEBOARD
MAIN BOARDCN101
TP(TE)
TP(VC)
A
M102(SPINDLE)M
BLK
RED
YEL
BLU
1-679-421-
12
(12)
TP(RFAC)
R111
R116
1-679-421-
12
(12)
B
C
D
E
F
G
H
I
J
K
1 2 3 4 5 6 7 8 9 10 11 12 13
A
(Page 28)
CDX-565MXRF
2727
MAINBOARDCN101(1/3)
Q101MSB709
-RT1
Q102MUN2212T1
6-6. SCHEMATIC DIAGRAM – RF/LSW Boards – • See page 33 for Waveforms. • See page 36 for IC Block Diagrams.
The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque 0 sontcritiques pour la sécurité. Ne les remplacer quepar une pièce portant le numéro spécifié.
(Page 30)
CDX-565MXRF
2828
IC101
IC601
IC604
IC201
IC602
IC102
IC306
IC401
IC302
IC301
IC303
IC603
IC605
1
26
ARF
BOARDCNJ101
MAINFLEXIBLEBOARD
61
60
90
91
120
1 30
31
1732
33
48
49 64
16
1
1 3
5 4
125
26
50
7551
100
76
1-168-744-
11
(11)
1
13
26
14
43
12
MAIN BOARD (COMPONENT SIDE)
B FM BOARDCN701
FM FLEXIBLE BOARD
3
1
4
5
SW201MAGAZINE
DETECT
1 2 3 4 5 6 7 8 9 10 11 12
A
B
C
D
E
F
G
H
I
J
K
13
54
6-7. PRINTED WIRING BOARDS – MAIN Board (Component Side) – • See page 25 for Circuit Boards Location.
• SemiconductorLocation
Ref. No. Location
D201 F-10D202 G-9D203 G-9D301 F-4D302 E-2D306 F-4D310 H-2
IC101 C-9IC102 E-7IC201 G-10IC301 H-3IC302 F-5IC303 G-3IC306 E-6IC401 B-7IC601 E-9IC602 G-7IC603 G-8IC604 E-10IC605 B-8
Q202 E-11Q205 G-9Q301 G-4Q302 G-4Q303 H-3Q304 G-2Q305 G-4Q402 D-6Q410 B-6Q420 C-6
(Page 26)
(Page 34)
CDX-565MXRF
2929
IC305
IC304
RV202ELEVATOR
HEIGHTSENSOR
(CHASSIS)
(CHASSIS)
M104(ELEVATOR)
M
RED
BLK
TP325
TP324
(CHASSIS)
TP331 TP332 TP330
TP802 TP803 TP801
RED
WHT
RED
MAIN BOARD (CONDUCTOR SIDE)
EJECT BOARD
(CHASSIS)
(RESET)
1-168-744- 11
(11)
1-68
4-74
6-
11
(11)
1 2 3 4 5 6 7 8 9 10 11 12
A
B
C
D
E
F
G
H
I
J
K
D303
6-8. PRINTED WIRING BOARDS – MAIN (Conductor Side)/EJECT Boards – • See page 25 for Circuit Boards Location.
• SemiconductorLocation
Ref. No. Location
D303 F-10
IC304 H-12IC305 F-12
CDX-565MXRF
3030
6-9. SCHEMATIC DIAGRAM – MAIN Board (1/3) – • See page 33 for Waveforms. • See page 36 for IC Block Diagram.
TP101
TP102
TP103
TP104
TP105
TP106
TP107
TP108
TP109
TP110
TP111
TP112
TP113
TP114
TP115
TP116
TP117
TP118
TP119
TP120
TP121
TP122
TP123
TP125
R125
R123
C122
C123
C121
C103
C102
C101
TP126
R122R101
R108
R109 C115
R102
R104
R103
C105
C107R105
C110
C109R106
R107
C1
06
C111 C108
C161
C162
C113
IC102
R117
C117
C104
R124 R120
R1
19
R121
C114
R116
C112
CN101
BP121
BP122
IC101
X101
R118
33k
100k
220p
0.1
220p
0.1
0.1
0.1
33k33k
470k
1M 1
10k
3.3k
3.3k
0.047
220p820k
1
0.01470k
10k
0.0
033
0.1 0.1
0.1
0.1
0.1
GM71VS17403CLT-6
220
10016V
0.0015
100 100
10
0
100
0.1
1k
0.1
26P
CXD3027R
16.9344MHz
330
A1
A2
A3
A4
A5
A6
A7
B1
B2
B3
B4
FRDR
MDP
SFDR
FFDR
TFDR
TRDR
SRDR
FRDR
FFDR
TRDR
TFDR
SRDR
SFDR
MDP
A4
A5
A6
A7
A8
A9
XOE
XCAS
D2
D3
D0
D1
XWE
XRAS
A10
A0
A1
A2
A3
XWE
XRAS
A10
A0
A1
A2
A3
XCAS
XOE
A9
A8
A7
A6
A5
A4
D0
D1 D2
D3
XW
RE
XR
DE
XQ
OK
SQ
SO
SQ
CK
SC
OR
XR
ST
DA
TA
XLA
T
CLO
K
SE
NS
SC
LK
REV
FWD
LIM
SW
SAVE
LOAD
FOK
ZZ1
ZZ2
ZZ3
ZZ4
ZZ1
ZZ2
ZZ3
ZZ4
YY
1
YY2
YY
3
YY
4
XX1
XX2
XX3
XX4
XX5
XX6
GR
SC
OR
GFS
LIM.SW
FRDR
FFDR
TFDR
TRDR
SFDR
SRDR
MDP
GND
GND
+8V
GND
FE
TE
RF
+8V
VC
+5V
SW
RFAC
+3.3V
GND
(1/3)
FLEXIBLE
BOARD
MAIN
CH.REV
CH.FWD
LOAD2
LOAD1
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR,
D-RAM CONTROLLER
D-RAM
(Page 31)
(Page 27)
(Page 32)
CDX-565MXRF
3131
6-10. SCHEMATIC DIAGRAM – MAIN (2/3)/EJECT Boards – • See page 33 for Waveforms. • See page 36 for IC Block Diagrams.
IC301
TP602 TP301
TP302
TP303
TP304
TP305
TP306
TP307
TP308
TP309
TP310
TP311
TP312
TP313
TP314
TP315
TP316
Q304
Q303
IC303
C301
CN301
R311C309 C310
D3
02
D3
10
R310
C318
IC306
C3
22
C3
21
C3
20
C3
23
R3
12
R306
C312
C317C319
R305
C316
R304D306
D301
R301
C307
R302
Q301
Q305
C304
C315
RB604
RB602
RB603
C605
R602
IC305
R608
C607
R6
07
C302
TP321
TP320
TP323
TP322
C603
C604
R601
C601
C608
R610C609
C611
IC603
C612
C606
C610
C616
R612
R613
IC604
C602
C614
IC605
R615C615
RB601
IC602C401
R405
R114
C120R111
R110C118
R406
C402
R401
R403
R402
R404
C410R414
C404
R408R410
R409 R407
C403
C409 R413
C411 R415
C412 R416
Q420
Q402C124
R113
R115
C116
C314C313
C613
C324
C119
R112
C303
D303
IC302
BP301
BP302
R303
Q302
IC304
TP801
TP802
TP803
TP331
TP332
TP330
TP325
TP324
M104
SW302SW301
Q410
IC401
IC601
TP601
LB1930M-TLM
MSD601-RT1
2SB1184-TLR
XC61CN2702NR
0.1
21P
100k0.1 0.1F5.5V
1S
R1
54
-40
0T
E-2
5M
A8051-H
-TX
33k
0.1
RH5RL33AA-T1
10
0p
10
0p
10
0p
10
0p
47
k
47k
0.1
0.1226.3V
100k
10016V
100kMM3Z7V5ST1
MM3Z16VST1
1k
0.01
1M
MSD601-RT1
DTA115EKA-T146
470k
100016V
100kX4
100k X4
100k X4
0.1
100k
NJM
23
96
AF0
5
270
0.33
27
0
0.1
0.1
0.1
1k
0.1
0.1
1M0.001
0.1
RN5RZ25BA-TL
0.1
0.1
4716V
100p
100
1k
TC7SH08FU-TE85R
0.1
0.1
TC7SH08FU-TE85R
1000.1
100kX4
W24L010AT-12-EL15
470p
10k
12k
1000p12k
12k330p
10k
470p
5.6k
5.6k
5.6k
5.6k
1016V 1K
10016V
33k10k
10k 10k
0.1
1016V
1K
100p 100k
100p 100k
DTC314TK-T-146
MUN2111T11000p
12k
12k
10016V
0.110016V
0.1
0.1
330p
12k
0.1
MTZJ-T-726.8B
TC74HCT7007AF(EL)
91k
MUN2211T1
NJM2396AF08
DTC314TK-T-146
TLV2362IPWR
CXD9684R-004
A1
A2
A3
A4
A5
A6
A7
C1
C2
C3
C4
C5
CE
IO2
IO3
IO4
IO5
IO6
IO7
EJECT
EV
ON
CD
ON
A11
A12
A5
A4
A3
A2
A1
A0
SDA
DECXRST
DEC
STB
Y
REV
FWD
RST
BUCHK
CE
CLK
DATA
L-DATA
L-CE
L-CLK
KEYIN
ENC2
LCDON
ACCIN
ENC1
A11
A9
A8
A13
A15
A16
A14
A12
A7
A6
A5
A4
WR2
SIRCS
L-CE
LCE
LCLK CLK
CE
PDATA
PCLK
PCEL-DATA
LDATA
L-CLK
DATA
YY1
YY2
YY4
XX1
XX2
XX3
XX4
XX5
XX6
OE
A10
CE
IO7
IO6
IO5
IO4
IO3
IO2
IO1
IO0
A0
A1
A2
A3
A15
A16
WR2
A14
A13
IO0
IO1
A6
A7
A8
A9
A10
DECINT
OE
OE
TC
-XR
DE
SCL
YY3
MU
TE
A11
A9
A8
A13
WE
CS2
A15
VDD
NC
A16
A14
A12
A7
A5
A6
A4
A10
CS1
IO8
IO7
IO6
IO5
IO4
GND
DQ3
DQ2
DQ1
A0
A1
A2
A3
IO2
IO3
IO4
IO5
IO6
IO7
VS
SP
PD
O
VC
OI
VD
DP
X1
X0
VS
SX
MIMD
AD0
AD1
AD2
AD3
AD4
AD5
LRCKIA
BCKIA
SDI0
AD
11
AD
12
OE
CK
S
TE
ST
P
VR
AR
RO
LO
VR
AL
ST
AN
BY
VSS
IO1
IO0
AD15
AD16
AD14
AD13
VSS
AD6
AD7
AD8
AD9
AD10
VDDT(3.3V)
VD
D(2
.5V
)
VD
AL(2
.5V
)
VD
AR
(2.5
V)
VDDT(3.3V)
VS
S(2
.5G
ND
)
VS
SL
(2.5
GN
D)
VS
SR
(2.5
GN
D)
VD
D(2
.5V
)
VD
DX
(2.5
V)
GND
NC
CE
L
G
R
GND
GND
GND
BUP
BUP
BUP
PLLCE
PLLCLK
PLLDATA
ACCIN
LCDDATA
KEYIN
LCDCE
LCDCLK
SIRCS
LCDON
ENCODER1
ENCODER2
XR
DE
SDO
ELV+
ELV-
EJECT
GND
RESET
VCC
GND
V
G
V
G
RESET
(CHASSIS)
(2/3)
(CHASSIS)
FLEXIBLE
BOARD
FM
BUS BUFFER
GATE SWITCHGATE SWITCH
+2.5V REGULATOR
O
REG
I
ELEVATOR
MOTOR DRIVE
Q301,305
CHECK
BATTERY HIGH VOLTAGE
DETECT VOUT VIN
NCGND
RESET SIGNAL
GENERATOR
+3.3V REGULATOR
Q303,304
REG
I O
GC
I
O
G
+3.3V REGULATOR
+8V REGULATORREG
I O
GC
(ELEVATOR)
(RESET)
(CHASSIS)
+5V REGULATOR
S-RAM
SWITCH
MUTING
CONTROL
MUTING
MUTING
ISOLATOR
GND
VCC
CD-ROM DECODER,
MP3 DECODER
I2C_SDA
I2C_SCL
CE
OE
REQ
WR
C4130.01
(Page 35)
(Page 32)
(Page 30)
Ver 1.1
CDX-565MXRF
3232
6-11. SCHEMATIC DIAGRAM – MAIN Board (3/3) – • See page 33 for Waveform.
D201
R215C207
X201
TP210
TP209
TP208
TP207
R232
R211
R201 D203
R217
R218
R216
R234
RV201
RV202
C203
C202
R204
C205
C204
R207
R235
SW201 R209 R208
R233
D202
R219
Q205
R231 C201
R220
R221
R222
TP211
TP203
R212
R213
C206
BP201
IC201
Q2021k
M1MA152WK-T1
0.01
12.288MHz
100k
100k
100k M1MA152WK-T1
100
100
1K
1k
47k
10k
0.1
0.1
0
0.1
0.1
1k
100k
470k 100k
1k
1SS355TE-17
10k
MUN2111T1
100k 0.1
10k
10k
100k
1k
100k
22006.3V
HD6432238RWN16TEIV
MUN2211T1
B1
B2
B3
C1
C2
C3
C4
C5
B4
CLO
K
XLA
T
DA
TA
XR
ST
TC
-XR
DE
DEC
STB
Y
DEC
XR
ST
SC
LK
SE
NS
FWD
REV
LIM
SW
SCL
SDA
SQCK
SQSO
SCOR
KEYIN
BUCHK
DECINT
XW
RE
LOAD
SAVE
XQ
OK
XR
DE
MUTE
GFS
FO
K
LCDON
LCLK
LDATA
LCE
KEYON
ENC1
ENC2
EJECT
RST
CDON
EVON
ACCIN
PCLK
PCE
PDATA
KEYACK
KEY
A
KE
YB
KEYA
KEYB
KEYON
KEYACK
GRSCOR
SIRCS
FWD
REV
EV
ON
DE
CX
RS
T
DE
CS
TB
Y
SC
LK
SE
NS
XR
ST
SCL
SDA
CDON
EVON
TES
T
MD
2
MD
1
MD
0
VC
C
AV
CC
AVSS
MC
K
R/RW_SEL
FO
K
GFS
CD
CL
K
CD
LA
T
CD
DA
T
LOADR
VS
S
XT
AL
EX
TA
L
FW
E
NC
NM
I
ST
BY
VS
S
EJEC
T
MG
LK
-SW
CV
CC
DO
UT
_S
EL
LCDCLK
SCOR
GRSCOR
EHS
NC
I
Vre
f
OS
C2
OS
C1
FL
_B
OO
T
FL
_W
NC
NC
DE
CIN
T
EECLK
NC
SQSO
SQCK
BUCHK
KEYINN
C
NC
NC
ENCODER1
ENCODER2
MAG
-SW
XQ
OK
XR
DE
XW
RE
DA
C-D
AT
A
DA
C-C
LK
DA
C-L
AT
ES
PS
EL
TE
XT
SE
L
CFS
EL
MUTE
NC
LCDON
PCTX
PCRX
LCDDATA
LCDCE
ELVF
ELVR
SIRCS
NCI
NCI
NCI
NCI
KEYACK
EEDATA
NC
PLLDATA
PLLCE
PLLCLK
NC
NC
LOADF
(3/3)
SYSTEM CONTROLLER
KEYON
RE
S
ACCIN
LIM_SW
SAVE_SW
LOAD_SW
SINGLE
RV202
ELEVATOR
HEIGHT
SENSOR
MAGAZINE
DETECT
SW201
(ON:WHEN MAZAGINE IS SET)
SWITCH
ACTIVE
KEY
CD-ROM/RW
SELECT SWITCH
0.5%
0.5%
0.5%
(Page 30)
(Page 31)
Ver 1.1
CDX-565MXRF
3333
3.5 Vp-p
22.7 µs
• Waveforms– RF Board –
1 IC101 qh (FE)
2 IC101 qk (TE)
3 IC101 qg (RFAC)
– MAIN Board –
1 IC101 rd (MDP)
2 IC101 ih (LRCK), ij (LRCKI)
3 IC101 o; (BCK), oz (BCKI)
4 IC101 of (XTAO)
5 IC601 qd (BCKIA)
6 IC601 qf (LRCKIA)
7 IC601 ys (X1)
8 IC201 yg (EXTAL)
Approx.100 mVp-p
Approx.250 mVp-p
1.4 ± 0.3 Vp-p
2 Vp-p
3.8 µs
3.5 Vp-p
472 ns
3 Vp-p
59.1 ns
3.5 Vp-p
472 ns
3.5 Vp-p
22.7 µs
3 Vp-p
59.1 ns
2.2 Vp-p
81.4 ns
1 IC701 qa (RF OUT)
655 mVp-p
14.3 ns
– FM Board –
2 IC701 qd (XOUT)
3.5 Vp-p
131.6 ns
CDX-565MXRF
3434
6-12. PRINTED WIRING BOARDS – FM Board – • See page 25 for Circuit Boards Location.
IC701
9
IC304
FM BOARD (COMPONENT SIDE)
1-684-817-
11
(11)
1 11
1222
BMAIN
BOARDCN301
FMFLEXIBLEBOARD
23 1
F1BATT
ACC
GND
RED
BLKYEL
RELAY BOX
FROMCAR ANTENNA
TOMASTER UNIT
OUTPUT
CN703
WIREDREMOTE COMMANDER
RM-X83RFFM BOARD(CONDUCTOR SIDE)
POWER
DISPLAY
CN302
(CHASSIS)
1-684-817-
11
(11)
1 2 3 4 5 6 7 8 9 10 11
B
C
D
E
F
G
A
(Page 28)
• SemiconductorLocation
Ref. No. Location
D301 D-8D313 C-10D314 E-11D701 E-8D702 G-5
IC304 D-8IC701 F-4
Q308 E-3Q701 G-5Q702 G-5
Ver 1.1
CDX-565MXRF
3535
6-13. SCHEMATIC DIAGRAM – FM Board – • See page 33 for Waveforms. • See page 36 for IC Block Diagram.
R722
C322C332 C323 C303 C305
R311 C320 R310 R313
R314
C333
Q308
TP707 R702
R703
R704
C701
C702
R701
C7
03
C7
04
R7
24
R7
05
R7
06
R7
07
C7
06
C7
05
C7
26 X701
TP
70
5
TP
70
4
TP
70
3
D301
TP717
R711
C715R716 R717
R726
RV701
R713 R714
C717
R715 C719
C714
R712
R718
C720
C718 C721
Q701
Q702
C716
C708 C7
09
C713
L702R719C722
C723 C724 R721
C725
R728 D701 L703
C712
C707
R727
TP709
TP710
TP711
R312
R317
R321
R320
R319
R316
TP712
TP713
TP714
TP715
TP716
TP718
TP719
D3
14
C3
28
C3
31
C3
29
D3
13
C3
27
C3
26
C3
25
TP702
TP701
CN701
C711
R723
TP721
TP720
TP706
IC701
IC304
D702
CN303
L701
CN302
F1
CN703
C7
10
TP708
470
10016V0.022 0.22 0.22 220
16V
22k 1050V 47k 4.7k
4.7k
100p
2SC2412K-T-146-Q
10k
2.2k
2.2k
1016V
1016V
10k
0.0
02
2
15
0p
22
k
1k
1k
1k
33
p
22
p
0.0
02
2
7.6MHz
1N5404TU
100
0.04710k 1k
0
10k
3.3k 3.3k
220p
10k 47p
1016V
5.6k
27
10p
0.0022 10p
2SC2412K-T-146-Q
2SC2412K-T-146-Q
100 16V
0.0022
15
0p
1
3300.001
47p 47p 82
0.1
0 1SS355TE
1
1
0
47k
470
0
470
470
100
MM
3Z6V
8S
T1
10
0p
10
0p
10
0p
MM
3Z6V
8S
T1
10
0p
10
0p
10
0p
21P
1016V
0
BH1415F-E2
NJM2396F05
HVU202A3TRF
3P
8P
2.2K
3A
10
16
V
DA
TA
CLK
CE
CE
CLK
DATA
SIRCS
LCDCLK
LCDCE
KEYA/D
LCDDATA
L
G
R
GND
GND
GND
BUP
BUP
BUP
PLLCE
PLLCLK
PLLDATA
LCDDATA
LCDCE
LCDCLK
SIRCS
LCDON
ENCODER2
ENCODER1
ENCODER2
ENCODER1
GND
B.UP
ACC
POWER ON
GND
FM STEREO
TRANSMITTER
RIN
R_
EM
R_
LP
F
FIL
TER
CO
MP
_O
UT
GN
D
PD
VC
C
RF_
IN
RF
_G
ND
RF_
OU
T
LIN
L_
EM
L_
LP
F
AD
J
MU
T
DA
TA
CL
K
CE
XIN
XO
UT
PL
LV
CC
TRANSMITTER
RV701
SENSITIVITY
MODULATION
+5V REGULATOR REG
I O
GC
ACCESSORY
CHECK
ACCIN
KEYIN
FLEXIBLE
BOARD
FM
Q701,702
BUFFER AMP
POWER
DISPLAY
ACC
BATT
GND
REMOTE COMMANDER
RM-X83RF
OUTPUT
RELAY
BOX
FROM
CAR
ANTENNA
TO
MASTER
UNIT
2.2µH
R7
29
0
WIRED
(Page 31)
Ver 1.1
CDX-565MXRF
3636
RW/ROM
RW/ROM
EQ ON/OFF
VOFST
VOFSTDVC
VC
VC
VC
RW/ROM
VC
DVC
3029
28+–+
–
DVCVCC
DVC
27
262524
RW/ROM
EQ
23
22
21
20
19
RFACVCA
VCC
+–
DVC
+–
+–
RW/ROM
VC
RW/ROM
DVC
+–
3
A
B
C
D
BC
A
A
A
BCD
B C D D
+–
1
2 APC AMP
5
6789
4RFAC
SUMMINGAMP
RW/ROM
APC-OFF(Hi-Z)
RW/ROM(H/L)
VOFST
VC
RW/ROM
+–
10
11
GM
GM
18
17
16
B
D
A
C
13
14
15
12
EQ IN
LD
PD
GND
ABCD
AC SUM
E
F
DVCC
DVC
RFAC
SW
DC OFSTRFDCI
RFDCO
VC
RFCVFCBST
RFG
VCC
CEI
CE
TE BAL
TE
FEI
FE
• IC Block Diagrams– RF Board –
IC101 CXA2581N-T4 INPUTFWDREV
VCC2
VLO–
VLO+
VO4+
VO4–
VO3+
VO3–
VO2+
VO2–
VO1+
VO1–
VCC1
VIN1
VIN1–A
VIN1+A
VIN1–B
S-GND
MUTE2
MUTE1
VIN4
VIN4–
VIN4+
VREF-IN
VIN1 (VREF)-SW
VREF-OUT (CH1)
REG-OUT
REG-IN
VIN3+
VIN3–
VIN3
VIN2+
VIN2–
VIN2
VIN1+B
OUTPUTCONTROL
+–
+–
+–
+–
+–
+–
LEVELSHIFT
CH2-4MUTE
THERMAL SHUT DOWN
CH1MUTE
VIN1/VREFSWITCH
5VREG
3
4
5
6
7
8
9
21
LEVELSHIFT
LEVELSHIFT
10
11
14
LEVELSHIFT
AMP-A
AMP-B
+–
15
16
17
18
23
19
34
35
36
+–+
–
+–+
–
25
24
22
21
20
33
32
31
30
29
28
+–
27
26
12
13
IC201 LA6576L-TE-L
37
CDX-565MXRF
– MAIN Board –
IC101 CXD3027R
ERRORCORRECTOR
32KRAM
EFMDEMODULATOR
SUB CODEPROCESSOR
SERVOAUTO
SEQUENCER
D/AINTERFACE
VIBRATIONMEMORY
CONTROLLER+
COMPRESSIONEXPANDER
DAC
SELECTOR
DIGITALOUT
ASYMMETRYCORRECTOR
DIGITALPLL
DIGITALCLV
CPUINTERFACE
OP AMPANALOG SWITCH
SERVO BLOCK
SIGNALPROCESSOR
BLOCK
MEMORY CONTROLLER,BUS BOOST BLOCK
A/DCONVERTER
SERVOINTERFACE
SERVO DSPFOCUS SERVO
SLED SERVO
TRACKING SERVO
CLOCKGENERATOR
LPF
LPF
MIRRDFCTFOK
PWM GENERATOR
FOCUS PWMGENERATOR
SLED PWMGENERATOR
TRACKING PWMGENERATOR
908988878685848382818079787776757473727170696867666564636261
123456789101112131415161718192021222324252627282930
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
XOE
A0 – A11
SYSMAMUTE
HPLHPMHPR
PCMDILRCKIBCKI
AOUT1AIN1
LOUT1
LOUT2AIN2
AOUT2
A9A8A7
DVSS
RFAC
XTAO
XTAI
XTSL
VCTL
VPCO
WFC
KGF
SXU
GFM
DS
C2PO
WDC
K
BIASASYIASYO
FILOFILIPCO
PWMILOCKMDP
SDTISCSYSCORSBSOEXCKSDTOXLATCLOKSENSXSOER4M
IGEN
VDD0
COUT
MIR
RDF
CT FOK
PWM
ILO
CKHP
RHP
MHP
LVD
D1C1
76M
DPM
DSSS
TPSF
DRSR
DRTF
DRTR
DRFF
DRFR
DR
FRDRFFDRTRDRTFDRSRDRSFDR
SCLKATSK
SSTPCOUT
FOKDFCTMIRR
VSS1
TEST
TES1
AVDD
0IG
ENAV
SS0
RFDC
E F
120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91
XOE
XCAS
D2 D3 D0 D1 XWE
XRAS
A11
A10
DVDD
A0 A1 A2 A3 AVDD
2LO
UT2
AIN2
AOUT
2AV
SS2
AVSS
1AO
UT1
AIN1
LOUT
1AV
DD1
XVSS
XTAO
XTAI
XVDD
BCKI
XOE
XCAS D2 D3 D0 D1 XWE
XRAS
A11
A10
DVDD A0 A1 A2 A3
AVDD
2LO
UT2
AIN2
AOUT
2AV
SS2
AVSS
1AO
UT1
AIN1
LOUT
1AV
DD1
XVSS
XTAO
XTAI
XVDD
BCKI
VDD0
COUT
MIR
RDF
CTFO
KPW
MI
LOCK
HPR
HPM
HPL
VDD1
MDP
MDS
SSTP
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
VSS1
A VD
D
A GN
D
D VD
D
AVDD
0IG
ENAV
SS0
RFDC E F
RFDCEFBA
VC
CLTVXPCK
A6A5A4
XWREXRDEXEMPXWIHXQOK
AMUTESDTI
XQCKSCSYSCORVSS0SBSOEXCKXRSTSYSMSDTOXLATCLOKSENSSCLKXSOEATSKR4M
A9A8A7
DVSSA6A5A4
XWREXRDEXEMPXWIHXQOK
AMUTESDTI
SCSYSCORVSS0
D GNDSBSOEXCK
SYSMSDTOXLATCLOKSENSSCLKXSOEATSKR4M
BCKPCMDIPCMDLRCKILRCKDOUTVDD2WFCKC2POGFSXPCKXUGFWDCKVSS2XTSLAVDD3ASYOASYIBIASRFACAVSS3CLTVPCOFILIFILOVCTLVPCOVCAB
BCKPCMDIPCMDLRCKILRCKDOUTVDD2WFCKC2POGFS
XPCKXUGFWDCKVSS2XTSL
AVDD3ASYOASYIBIASRFAC
AVSS3CLTVPCOFILIFILOVCTLVPCO
VCAB
XCAS
D0 – D4
XWE
BCKPCMDLRCK
DOUT
XWRE
XRAS
XRDE
XQOKXWIHXEMP
38
CDX-565MXRF
IC601 CXD9684R-004
2
1 RESET
MIMD
3 AD0
4 AD1
5 MIDIO
6 MICK
7 AD2
8 VDDT
9 SDO
10 AD3
11 AD4
12 SDI0
13 BCKIA
14 LRCKIA
15 AD5
16 CE
17
OE
18
VDD
19
STAN
DBY
20
VSS
21VS
SL22
VRAL
23
LO
24
VDAL
25
VDAR
26
RO
27
VRAR
28
VSSR
29
TEST
P
30
CKS
31
AD12
32
AD11
64
VSSX
63
XO
62
XI
61
VDDX
60
CKO
59
VDDP
58
VCOI
57
PDO
56
VSSP
55
IO7
54
IO6
53
IO5
52
VDD
51
IO4
50
IO3
49
IO2
48VSS
47IO1
46IO0
45AD15
44AD16
43WR
42AD14
41AD13
40VSS
39REQ
38AD6
37AD7
36AD8
35VDDT
34AD9
33AD10
TIMINGGENERATORVCOPROG.
START DITGENERALINPUT PORT
INTERRUPTCONTROL
SRAM I/F
I-BUS
TIMER
DACDAC
BUSSWITCH
Y-POINTERREGISTER
X-POINTERREGISTER
C-POINTERREGISTER
ERAM2k WORD
XRAM4k WORD
YRAM4k WORD
CROM4k WORD
x3
ALU
A2
A3
AXAY
ROUND & LIMIT
MAC
A0
A1
MX
MY
MZ
IINSTRUCTIONDECODER
PROM4kx2+2k
=10k WORD
40 BIT
PRAM256 WORD
PROGRAMCONTROL
Y-BU
S
X-BU
S
GENERALOUTPUT
PORT
FLAG
ADDRESSCALC.2 SETS
MICROCOM.I/F
AUDIOI/F
REGISTERX0 X1 X2Y0 Y1 Y2
ROUND & LIMIT
12
3
4
5 6
789
10VCC
IN2
S-GND
IN1
NCNC
OUT2NC
P-GND
OUT1CONTROLCIRCUIT
MOTORDRIVE
CIRCUIT
BUFFER
BUFFER
IC301 LB1930M-TLM
39
CDX-565MXRF
– FM Board –
IC701 BH1415F-E2
+–
+–
PHASEDETECTOR
22 21 20 19 18 17 16 15 14 13 12
1 2 3 4 5 6 7 8 9 10 11
L. P. F.
L. P. F.
SHIFT REGISTER
PROGRAM COUNTER
14
150
119
VCC2
MUTEMPX
OSC
0
+
12
RF
PRE-EMPHASIS& LIMITER
L-CH
INPU
T
PRE-
EMPH
ASIS
TIM
E CO
NSTA
NT
LPF
TIM
E CO
NSTA
NT
PILO
T SI
GNAL
ADJ
UST
AUDI
O M
UTIN
G
DATA
CLOC
K
CHIP
ENA
BLE
X'TA
L OS
CILL
ATOR
X'TA
L OS
CILL
ATOR
PLL
VCC
R-CH
INPU
T
PRE-
EMPH
ASIS
TIM
E CO
NSTA
NT
LPF
TIM
E CO
NSTA
NT
FILT
ER
COM
POSI
TE S
IGNA
L OU
TPUT
GND
PLL
PHAS
E DE
TECT
OR O
UTPU
T
VCC
RF O
SCIL
LTOR
RF G
ND
RF O
UTPU
T
40
CDX-565MXRF
6-14. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC201 HD6432238RWN16TEIV (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 TEST I Test mode setting terminal “L”: test mode Not used
2 DECXRST O Reset signal output to the CD-ROM/MP3 decoder “L”: reset
3 DECSTBY O Standby mode control signal output to the CD-ROM/MP3 decoder “H”: standby
4 FOK I Focus OK signal input from the DSP “L”: NG, “H”: OK
5 GFS I Guard frame sync signal input from the DSP “L”: NG, “H”: OK
6 SCLK O Serial data reading clock signal output to the DSP
7 SENS I Internal status signal (sense signal) input from the DSP
8 CDCLK O Serial data transfer clock signal output to the DSP
9 CDLAT O Serial data latch pulse signal output to the DSP
10 CDDAT O Serial data output to the DSP
11 XRST O System reset signal output to the DSP “L”: reset
12 CVCC — Power supply terminal (+3.3V) (for system)
13 NC O Not used
14 VSS — Ground terminal
15 XQOK O Subcode Q OK pulse signal output to the DSP
16 XRDE O Read enable signal output to the DSP
17 XWRE O Write enable signal output to the DSP
18 DAC-DATA O Mode control data output terminal Not used
19 DAC-CLK O Mode control data transfer clock signal output terminal Not used
20 DAC-LAT O Mode control data latch pulse signal output terminal Not used
21 ESPSEL I ESP mode setting terminal “L”: ESP on (fixed at “L” in this set)
22 TEXTSEL I CD text mode setting terminal “L”: CD text on (fixed at “L” in this set)
23 CFSEL I Custom file on/off setting terminal “L”: custom file on Not used
24 DOUT SEL I Input terminal for digital out on/off setting “L”: digital out on Not used
25 MAG-SW I Magazine detect switch input terminal Not used
26 MUTE O Audio line muting on/off control signal output “H”: muting on
27 NC O Not used
28 LCDON OThe LCD in remote commander and FM transmitter section power supply on/off control signaloutput “H”: power on
29 CDON O D/A convert and servo sections power supply on/off control signal output “H”: power on
30 EVON O Mechanism deck section power supply on/off control signal output “H”: power on
31 PCTX O PC connecting output terminal for UART Not used
32 PCRX I PC connecting input terminal for UART Not used
33 LCDCLK O Serial data transfer clock signal output to the LCD driver in remote commander
34 LCDDATA O Serial data output to the LCD driver in remote commander
35 LCDCE O Chip enable signal output to the LCD driver in remote commander “H” active
36 ELVF O Motor drive signal (elevator up direction) output to the elevator motor drive
37 ELVR O Motor drive signal (elevator down direction) output to the elevator motor drive
38 SCOR I Subcode sync (S0+S1) detection signal input from the DSP
39 KEYON O Power supply on/off control signal output for the A/D converter “L”: power on
40 GRSCOR I Subcode sync (S0+S1) detection signal input from the DSP
41 SIRCS I SIRCS signal input from the remote commander
42 AVSS — Ground terminal (for A/D converter)
43 to 46 NCI I Not used
47, 48ENCODER1,ENCODER2
I Dial pulse input from the rotary encoder in remote commander
41
CDX-565MXRF
Pin No. Pin Name I/O Description
49 KEYIN I Key input (A/D input) from the remote commander
50 EHS I Elevator height position detection signal input from the elevator height sensor (A/D input)
51 NCI I Not used
52 MCK IInput of detection signal for the fine adjustment (elevator height (address) adjustment) of elevatorheight position (A/D input)
53 VREF I Reference voltage (+3.3V) input terminal (for A/D converter)
54 AVCC — Power supply terminal (+3.3V) (for A/D converter)
55, 56 MD0, MD1 I Setting terminal for the CPU operational mode “H”: single chip mode (fixed at “H” in this set)
57 OSC2 O Sub system clock output terminal Not used
58 OSC1 I Sub system clock input terminal Not used (fixed at “L”)
59 RES ISystem reset signal input from the reset switch and reset signal generator “L”: resetFor several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
60 NMI O Not used (fixed at “H”)
61 STBY O Standby mode control signal output terminal Not used (fixed at “H”)
62 VCC — Power supply terminal (+3.3V)
63 XTAL I Main system clock input terminal (12.288 MHz)
64 VSS — Ground terminal
65 EXTAL O Main system clock output terminal (12.288 MHz)
66 FWE I Flash memory data write enable signal input terminal
67 MD2 I Setting terminal for the CPU operational mode “H”: single chip mode (fixed at “H” in this set)
68 FL BOOT I Flash memory data write control signal input terminal “L” active Not used
69 FL W O Flash memory data write control signal output (connecting FWE (pin 66))
70, 71 NC O Not used
72 MGLK-SW I Magazine in/out detect switch input terminal “L”: magazine in
73 DECINT I Interrupt signal input from the CD-ROM/MP3 decoder
74 NC O Not used
75 EJECT I Eject switch input terminal “L” active
76 NC O Not used
77 NC I Not used
78 KEYACK IInput of acknowledge signal for the key entryAcknowledge signal is input to accept from the remote commander in the power off status
79 EEDATA I/O Two-way data bus with the EEPROM Not used
80 SDA I/O I2C interface data input/output with the CD-ROM/MP3 decoder
81 SCL O I2C interface data transfer clock signal output to the CD-ROM/MP3 decoder
82 EECLK O Serial data transfer clock signal output to the EEPROM Not used
83 NC O Not used
84 SQSO I Subcode Q data input from the DSP
85 SQCK O Subcode Q data reading clock signal output to the DSP
86 NC O Not used
87 PLLDATA O Serial data output to the FM stereo transmitter
88 PLLCE O Chip enable signal output to the FM stereo transmitter “H” active
89 PLLCLK O Serial data transfer clock signal output to the FM stereo transmitter
90 R/RW SEL O CD-ROM/RW selection signal output “L”: CD-RW, “H”: CD-ROM
91 ACCIN I Accessory detection signal input “L”: accessory on
92 BUCHK I Battery detection signal input “H”: low battery (Normally: “L”)
93, 94 NC O Not used
95 LOADF O Motor drive signal (load chucking direction) output to the chucking motor drive
42
CDX-565MXRF
Pin No. Pin Name I/O Description
96 LOADR O Motor drive signal (save direction) output to the chucking motor drive
97 SINGLE ISetting terminal for the single disc/multiple discs mode“L”: single disc mode, “H”: multiple discs mode (fixed at “H” in this set)
98 LOAD SW IChucking end detect switch input terminal“L”: When completion of the disc chucking operation
99 SAVE SW ISave end detect switch input terminal“L”: When completion of the disc save operation
100 LIM SW ISled limit in detect switch input terminal“L”: When the optical pick-up is inner position
43
CDX-565MXRF
7-1. GENERAL SECTION-1
SECTION 7EXPLODED VIEWS
Les composants identifiés par unemarque 0 sont critiquens pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when orderingthese items.
• The mechanical parts with no reference num-ber in the exploded views are not supplied.
• Accessories are given in the last of the elec-trical parts list.
NOTE:• -XX and -X mean standardized parts, so they
may have some difference from the originalone.
• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑Parts Color Cabinet's Color
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-3381-752-1 DOOR (M) ASSY2 3-229-226-21 PANEL, FRONT3 3-047-886-11 LEVER (FLT. 838)4 3-237-609-21 CASE (UPPER. T)5 1-823-973-12 CORD (WITH CONNECTOR) (POWER)
6 A-3301-964-A RELAY BOX ASSY7 1-792-045-21 CORD (WITH CONNECTOR)(ANT-OUT)
(for RELAY BOX ASSY)
8 1-792-044-23 CORD (WITH CONNECTOR) (CD-OUT)(for RELAY BOX ASSY)
9 A-3220-842-A WIRED COMMANDER (RM-X83RF)10 1-823-920-22 CABLE WITH CONNECTOR 8P (for RM-X83RF)F1 1-532-731-11 FUSE (BLADE TYPE) (AUTO FUSE) (3A/32V)#2 7-685-792-09 SCREW +PTT 2.6X6 (S)
3
21
#2
#2
#2
#2
general section-2
3
#2
4
5
6
9 10
78
F1
Ver 1.1
44
CDX-565MXRF
7-2. GENERAL SECTION-2
66
6662
65
63
64
#3
#3
RV202
main board
57
58
56
53
59 71
60
60#1
not supplied
not supplied
not supplied
not supplied
not supplied
54
52
51
51
not supplied
61
67
55
68
MG-251B-137
60
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 3-047-852-01 DAMPER (T)52 X-3381-753-1 CASE (LOWER T) ASSY53 A-3274-259-A FM BOARD, COMPLETE
* 54 3-046-989-03 PLATE (FM), SHIELD55 3-244-890-01 PLATE (MAIN) (MP3), SHIELD
56 1-676-735-11 FM FLEXIBLE BOARD57 3-042-999-11 COVER (FM CONNECTOR. T)58 3-913-406-11 SCREW (GROUND)59 X-3375-357-1 ARM (FLT) ASSY60 3-935-636-11 SCREW (FP)
61 1-684-746-11 EJECT BOARD62 3-042-244-11 SCREW (T)
63 3-041-218-21 ESCUTCHEON (T)64 3-022-007-02 BUTTON (EJT) (Z)
* 65 3-022-012-01 HEAT SINK (T)66 3-038-166-01 SPRING (FL), TENSION COIL67 A-3274-255-A MAIN BOARD, COMPLETE
68 1-676-339-12 MAIN FLEXIBLE BOARD71 X-3375-360-2 ARM (FRT) ASSYRV202 1-227-137-11 RES, VAR, SLIDE 10K
(ELEVATOR HEIGHT SENSOR)#1 7-685-862-09 SCREW +BVTT 2.6X6 (S)#3 7-685-781-09 SCREW +PTT 2X4 (S)
45
CDX-565MXRF
7-3. MECHANISM DECK SECTION-1(MG-251B-137)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
101 X-3378-091-1 CHASSIS (U. S) SUB ASSY102 3-024-161-01 SPRING (SUT)
103 3-011-997-01 SPRING (STOPPER. LOWER)#3 7-685-781-09 SCREW +PTT 2X4 (S)
#3
#3
#3
mechanism deck section-3
101
102
103
mechanism deck section-2
46
CDX-565MXRF
7-4. MECHANISM DECK SECTION-2(MG-251B-137)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
151 3-024-170-01 SPRING (SB), TENSION* 152 3-040-790-02 BRACKET (EVM. S)
153 X-3378-092-7 CHASSIS (D. S) SUB ASSY
* 154 3-014-685-01 SPACER (MO)M104 A-3301-123-A ELJ MOTOR ASSY (ELEVATOR)#3 7-685-781-09 SCREW +PTT 2X4 (S)
151
152
154
153
#3
M104
47
CDX-565MXRF
213
212
211
210
209
202
201
214207
206
208204
205
#8
#4
#6
#6#3
#6
#3
M103
#8
mechanism deck section-4
7-5. MECHANISM DECK SECTION-3(MG-251B-137)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 201 3-024-150-01 RETAINER (CHM)* 202 X-3378-080-1 BRACKET (CHM. D) ASSY
204 3-321-813-01 WASHER, COTTER POLYETHYLENE205 3-017-139-01 GEAR (WORM LOAD A)206 3-022-839-02 ARM (NSW)
207 3-573-936-00 STOPPER, REEL208 X-3373-552-1 GEAR (LOAD 1) ASSY209 3-010-252-11 ROLLER (CRE)210 3-010-268-01 SPRING (DH), TENSION
* 211 A-3290-194-M MAIN ASSY, CHASSIS (EVY)212 3-010-254-11 SHAFT (ROTARY PREVENTION C)213 3-010-253-01 GEAR (LOMINI)
* 214 A-3326-947-A RF BOARD, COMPLETEM103 A-3301-123-A ELJ MOTOR ASSY (CHUCKING)
#3 7-685-781-09 SCREW +PTT 2X4 (S)#4 7-624-104-04 STOP RING 2.0, TYPE-E#6 7-628-253-00 SCREW +PS 2X4#8 7-624-102-04 STOP RING 1.5, TYPE-E
48
CDX-565MXRF
258
256255
254
253
260
252
251
257
259
M101
not supplied
not supplied
not supplied
not supplied
#10
#11
#11
#5
M102
#7
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
7-6. MECHANISM DECK SECTION-4(MG-251B-137)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
251 1-676-341-11 OP FLEXIBLE BOARD252 3-025-743-01 SPRING (FEED), LEAF253 X-3378-101-2 HOLDER (SLED. S) ASSY254 3-931-832-01 GEAR (SL MIDWAY)
0255 8-820-103-11 OPTICAL PICK-UP KSS-720A/C-RP
256 A-3291-669-A SHAFT (FEED) ASSY257 3-010-263-01 DETENT (SHAFT THRUST)
* 258 1-679-422-12 LSW BOARD
259 A-3301-954-C BASE (OPT. S) (J) ASSY260 3-241-673-01 SCREW (SM), SPECIALM101 A-3315-151-A SLED MOTOR ASSY (251)M102 A-3301-998-A SPINDLE MOTOR (S) SUB ASSY#5 7-627-554-07 SCREW, PRECISION +P 2X2.2
#7 7-627-553-27 SCREW, PRECISION +P 2X2.5#10 7-627-000-00 SCREW, PRECISION +P 1.7X2.2 TYPE 3#11 7-627-553-37 PRECISION SCREW +P 2X3 TYPE 3
49
CDX-565MXRFSECTION 8
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:• Due to standardization, replacements in the
parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.
• -XX and -X mean standardized parts, so theymay have some difference from the originalone.
• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable
• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.
• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .
• CAPACITORSuF: µF
• COILSuH: µH
1-684-746-11 EJECT BOARD************
< SWITCH >
SW301 1-692-431-21 SWITCH, TACTILE (Z)SW302 1-692-431-21 SWITCH, TACTILE (RESET)
**************************************************************
A-3274-259-A FM BOARD, COMPLETE********************
< CAPACITOR >
C303 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC305 1-128-499-11 ELECT 220uF 20% 16VC320 1-124-233-11 ELECT 10uF 20% 50VC322 1-125-972-11 ELECT 100uF 20% 16VC323 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C325 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC326 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC327 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC328 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC329 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C331 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC332 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC333 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC701 1-124-233-11 ELECT 10uF 20% 16VC702 1-124-233-11 ELECT 10uF 20% 16V
C703 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC704 1-164-217-11 CERAMIC CHIP 150PF 5% 50VC705 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC706 1-162-921-11 CERAMIC CHIP 33PF 5% 50VC707 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C708 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC709 1-164-217-11 CERAMIC CHIP 150PF 5% 50VC710 1-124-233-11 ELECT 10uF 20% 16VC711 1-124-233-11 ELECT 10uF 20% 16VC712 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C713 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3VC714 1-124-233-11 ELECT 10uF 20% 16VC715 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC716 1-126-382-11 ELECT 100uF 20% 16VC717 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C718 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC719 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C720 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC721 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC722 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C723 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC724 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC725 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC726 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
< CONNECTOR >
CN302 1-794-066-11 CONNECTOR, MINIATURE DIN 8P (DISPLAY)CN303 1-793-286-11 PIN, CONNECTOR (PC BOARD) 3P (POWER)CN701 1-784-829-21 CONNECTOR, FPC 21PCN703 1-566-822-41 JACK (OUTPUT)
< DIODE >
D301 8-719-049-38 DIODE 1N5404TUD313 8-719-056-83 DIODE MM3Z6V8ST1D314 8-719-056-83 DIODE MM3Z6V8ST1D701 8-719-988-61 DIODE 1SS355TE-17D702 8-719-058-78 DIODE HVU202A3TRF
< IC >
IC304 6-702-146-01 IC NJM2396F05IC701 8-759-680-25 IC BH1415F-E2
< COIL >
L701 1-419-467-11 COIL, IFTL702 1-411-845-11 COIL, AIR-COREL703 1-410-997-42 INDUCTOR 2.2uH
< TRANSISTOR >
Q308 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QQ701 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QQ702 8-729-120-28 TRANSISTOR 2SC2412K-T-146-Q
< RESISTOR >
R310 1-216-841-11 METAL CHIP 47K 5% 1/10WR311 1-216-837-11 METAL CHIP 22K 5% 1/10WR312 1-216-841-11 METAL CHIP 47K 5% 1/10WR313 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR314 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R316 1-216-809-11 METAL CHIP 100 5% 1/10WR317 1-216-817-11 METAL CHIP 470 5% 1/10WR319 1-216-817-11 METAL CHIP 470 5% 1/10W
Les composants identifiés par unemarque 0 sont critiquens pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
When indicating parts by referencenumber, please include the board.
EJECT FMVer 1.1
50
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
CDX-565MXRF
R320 1-216-817-11 METAL CHIP 470 5% 1/10WR321 1-216-864-11 SHORT CHIP 0
R701 1-216-833-11 METAL CHIP 10K 5% 1/10WR702 1-216-833-11 METAL CHIP 10K 5% 1/10WR703 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR704 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR705 1-216-821-11 METAL CHIP 1K 5% 1/10W
R706 1-216-821-11 METAL CHIP 1K 5% 1/10WR707 1-216-821-11 METAL CHIP 1K 5% 1/10WR711 1-216-809-11 METAL CHIP 100 5% 1/10WR712 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR713 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R714 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR715 1-216-833-11 METAL CHIP 10K 5% 1/10WR716 1-216-833-11 METAL CHIP 10K 5% 1/10WR717 1-216-821-11 METAL CHIP 1K 5% 1/10WR718 1-216-802-11 RES-CHIP 27 5% 1/10W
R719 1-216-815-11 METAL CHIP 330 5% 1/10WR721 1-216-808-11 METAL CHIP 82 5% 1/10WR722 1-216-817-11 METAL CHIP 470 5% 1/10WR723 1-216-864-11 SHORT CHIP 0R724 1-216-837-11 METAL CHIP 22K 5% 1/10W
R726 1-216-864-11 SHORT CHIP 0R727 1-216-864-11 SHORT CHIP 0R728 1-216-864-11 SHORT CHIP 0R729 1-242-792-11 SHORT CHIP 0
< VARIABLE RESISTOR >
RV701 1-238-090-11 RES, ADJ, CERMET 10K
< VIBRATOR >
X701 1-795-149-11 VIBRATOR, CRYSTAL (7.6MHz)**************************************************************
* 1-679-422-12 LSW BOARD***********
< SWITCH >
SW3 1-529-565-41 SWITCH, PUSH (1 KEY) (LIMIT)**************************************************************
A-3274-255-A MAIN BOARD, COMPLETE**********************
1-676-339-12 MAIN FLEXIBLE BOARD3-244-890-01 PLATE (MAIN) (MP3), SHIELD
< CAPACITOR/RESISTOR >
C101 1-164-156-11 CERAMIC CHIP 0.1uF 25VC102 1-164-156-11 CERAMIC CHIP 0.1uF 25VC103 1-164-156-11 CERAMIC CHIP 0.1uF 25VC104 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50VC105 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C106 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC107 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC108 1-164-156-11 CERAMIC CHIP 0.1uF 25VC109 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC110 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C111 1-164-156-11 CERAMIC CHIP 0.1uF 25VC112 1-164-156-11 CERAMIC CHIP 0.1uF 25VC113 1-164-156-11 CERAMIC CHIP 0.1uF 25VC114 1-164-156-11 CERAMIC CHIP 0.1uF 25VC115 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C116 1-126-382-11 ELECT 100uF 20% 16VC117 1-126-382-11 ELECT 100uF 20% 16VC118 1-162-959-11 CERAMIC CHIP 330PF 5% 50VC119 1-162-959-11 CERAMIC CHIP 330PF 5% 50VC120 1-115-416-11 CERAMIC CHIP 1000PF 5% 25V
C121 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC122 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC123 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC124 1-115-416-11 CERAMIC CHIP 1000PF 5% 25VC161 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C162 1-164-156-11 CERAMIC CHIP 0.1uF 25VC201 1-164-156-11 CERAMIC CHIP 0.1uF 25VC202 1-164-156-11 CERAMIC CHIP 0.1uF 25VC203 1-164-156-11 CERAMIC CHIP 0.1uF 25VC204 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C205 1-164-156-11 CERAMIC CHIP 0.1uF 25VC206 1-104-656-11 ELECT 2200uF 20% 6.3VC207 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC301 1-164-156-11 CERAMIC CHIP 0.1uF 25VC302 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C303 1-164-156-11 CERAMIC CHIP 0.1uF 25VC304 1-216-853-11 METAL CHIP 470K 5% 25VC307 1-162-970-11 CERAMIC CHIP 0.01uF 10% 1/10WC309 1-164-156-11 CERAMIC CHIP 0.1uF 25VC310 1-125-710-11 DOUBLE LAYER 0.1F 5.5V
C312 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC313 1-126-382-11 ELECT 100uF 20% 16VC314 1-164-156-11 CERAMIC CHIP 0.1uF 25VC315 1-115-466-00 ELECT 1000uF 20% 16VC316 1-126-382-11 ELECT 100uF 20% 16V
C317 1-164-156-11 CERAMIC CHIP 0.1uF 25VC318 1-164-156-11 CERAMIC CHIP 0.1uF 25VC319 1-127-491-00 ELECT (SOLID) 22uF 20% 10VC320 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC321 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C322 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC323 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC324 1-164-156-11 CERAMIC CHIP 0.1uF 25VC401 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC402 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C403 1-164-156-11 CERAMIC CHIP 0.1uF 25VC404 1-126-382-11 ELECT 100uF 20% 16VC409 1-124-233-11 ELECT 10uF 20% 16VC410 1-124-233-11 ELECT 10uF 20% 16VC411 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C412 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC413 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50VC601 1-164-156-11 CERAMIC CHIP 0.1uF 25VC602 1-164-156-11 CERAMIC CHIP 0.1uF 25VC603 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C604 1-164-156-11 CERAMIC CHIP 0.1uF 25VC605 1-164-156-11 CERAMIC CHIP 0.1uF 25VC606 1-164-156-11 CERAMIC CHIP 0.1uF 25V
FM LSW MAIN
51
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
CDX-565MXRF
C607 1-128-934-11 CERAMIC CHIP 0.33uF 20% 10VC608 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C609 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25VC610 1-124-589-11 ELECT 47uF 20% 16VC611 1-164-156-11 CERAMIC CHIP 0.1uF 25VC612 1-164-156-11 CERAMIC CHIP 0.1uF 25VC613 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C614 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC615 1-164-156-11 CERAMIC CHIP 0.1uF 25VC616 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
< CONNECTOR >
CN301 1-784-829-21 CONNECTOR, FPC 21P
< DIODE >
D201 8-719-050-38 DIODE M1MA152WK-T1D202 8-719-988-61 DIODE 1SS355TE-17D203 8-719-050-38 DIODE M1MA152WK-T1D301 6-500-030-01 DIODE MM3Z16VST1D302 8-719-053-18 DIODE 1SR154-400TE-25
D303 8-719-109-97 DIODE RD6.8ESB2D306 8-719-056-83 DIODE MM3Z7V5ST1D310 8-719-422-43 DIODE MA8051-H-TX
< IC >
IC101 8-752-398-18 IC CXD3027RIC102 8-759-538-44 IC MSM51V17400D-10TK-FSIC201 6-801-500-01 IC HD6432238RWN16TEIVIC301 8-759-527-33 IC LB1930M-TLMIC302 8-759-238-47 IC TC74HCT7007AF (EL)
IC303 6-702-148-01 IC XC61CN2702NRIC304 6-702-147-01 IC NJM2396F08IC305 6-702-146-01 IC NJM2396F05IC306 8-759-444-93 IC RH5RL33AA-T1IC401 8-759-662-11 IC TLV2362IPWR
IC601 6-700-297-01 IC CXD9684R-004IC602 6-700-296-01 IC W24L010AT-12-EL15IC603 8-759-645-31 IC RN5RZ25BA-TLIC604 8-759-196-96 IC TC7SH08FU-TE85RIC605 8-759-196-96 IC TC7SH08FU-TE85R
< TRANSISTOR >
Q202 8-729-421-22 TRANSISTOR MUN2211T1Q205 8-729-424-08 TRANSISTOR MUN2111T1Q301 8-729-010-25 TRANSISTOR MSD601-RT1Q302 8-729-421-22 TRANSISTOR MUN2211T1Q303 8-729-922-47 TRANSISTOR 2SB1184-TLR
Q304 8-729-010-25 TRANSISTOR MSD601-RT1Q305 8-729-028-62 TRANSISTOR DTA115EKA-T146Q402 8-729-424-08 TRANSISTOR MUN2111T1Q410 8-729-920-21 TRANSISTOR DTC314TK-T-146Q420 8-729-920-21 TRANSISTOR DTC314TK-T-146
< RESISTOR >
R101 1-216-839-11 METAL CHIP 33K 5% 1/10WR102 1-216-833-11 METAL CHIP 10K 5% 1/10WR103 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR104 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R105 1-218-917-11 RES-CHIP 820K 5% 1/10W
R106 1-216-853-11 METAL CHIP 470K 5% 1/10WR107 1-216-833-11 METAL CHIP 10K 5% 1/10WR108 1-216-853-11 METAL CHIP 470K 5% 1/10WR109 1-216-857-11 METAL CHIP 1M 5% 1/10WR110 1-216-834-11 METAL CHIP 12K 5% 1/10W
R111 1-216-834-11 METAL CHIP 12K 5% 1/10WR112 1-216-834-11 METAL CHIP 12K 5% 1/10WR113 1-216-834-11 METAL CHIP 12K 5% 1/10WR114 1-216-834-11 METAL CHIP 12K 5% 1/10WR115 1-216-834-11 METAL CHIP 12K 5% 1/10W
R116 1-216-821-11 METAL CHIP 1K 5% 1/10WR117 1-216-813-11 METAL CHIP 220 5% 1/10WR118 1-216-815-11 METAL CHIP 330 5% 1/10WR119 1-216-809-11 METAL CHIP 100 5% 1/10WR120 1-216-809-11 METAL CHIP 100 5% 1/10W
R121 1-216-809-11 METAL CHIP 100 5% 1/10WR122 1-216-839-11 METAL CHIP 33K 5% 1/10WR123 1-216-845-11 METAL CHIP 100K 5% 1/10WR124 1-216-809-11 METAL CHIP 100 5% 1/10WR125 1-216-839-11 METAL CHIP 33K 5% 1/10W
R201 1-216-845-11 METAL CHIP 100K 5% 1/10WR204 1-216-864-11 SHORT CHIP 0R207 1-216-821-11 METAL CHIP 1K 5% 1/10WR208 1-216-845-11 METAL CHIP 100K 5% 1/10WR209 1-216-853-11 METAL CHIP 470K 5% 1/10W
R211 1-216-845-11 METAL CHIP 100K 5% 1/10WR212 1-216-821-11 METAL CHIP 1K 5% 1/10WR213 1-216-845-11 METAL CHIP 100K 5% 1/10WR215 1-216-821-11 METAL CHIP 1K 5% 1/10WR216 1-216-821-11 METAL CHIP 1K 5% 1/10W
R217 1-216-809-11 METAL CHIP 100 5% 1/10WR218 1-216-809-11 METAL CHIP 100 5% 1/10WR219 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR220 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR221 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R222 1-216-845-11 METAL CHIP 100K 5% 1/10WR231 1-216-845-11 METAL CHIP 100K 5% 1/10WR232 1-216-845-11 METAL CHIP 100K 5% 1/10WR233 1-216-821-11 METAL CHIP 1K 5% 1/10WR234 1-216-821-11 METAL CHIP 1K 5% 1/10W
R235 1-216-845-11 METAL CHIP 100K 5% 1/10WR301 1-216-821-11 METAL CHIP 1K 5% 1/10WR302 1-216-857-11 METAL CHIP 1M 5% 1/10WR303 1-218-739-11 RES-CHIP 91K 5% 1/10WR304 1-216-845-11 METAL CHIP 100K 5% 1/10W
R305 1-216-845-11 METAL CHIP 100K 5% 1/10WR306 1-216-841-11 METAL CHIP 47K 5% 1/10WR310 1-216-839-11 METAL CHIP 33K 5% 1/10WR311 1-216-845-11 METAL CHIP 100K 5% 1/10WR312 1-216-841-11 METAL CHIP 47K 5% 1/10W
R401 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR402 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR403 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR404 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR405 1-216-833-11 METAL CHIP 10K 5% 1/10W
R406 1-216-833-11 METAL CHIP 10K 5% 1/10W
MAINVer 1.1
52
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
CDX-565MXRF
R407 1-216-833-11 METAL CHIP 10K 5% 1/10WR408 1-216-839-11 METAL CHIP 33K 5% 1/10WR409 1-216-833-11 METAL CHIP 10K 5% 1/10WR410 1-216-833-11 METAL CHIP 10K 5% 1/10W
R413 1-216-821-11 METAL CHIP 1K 5% 1/10WR414 1-216-821-11 METAL CHIP 1K 5% 1/10WR415 1-216-845-11 METAL CHIP 100K 5% 1/10WR416 1-216-845-11 METAL CHIP 100K 5% 1/10WR601 1-216-821-11 METAL CHIP 1K 5% 1/10W
R602 1-216-845-11 METAL CHIP 100K 5% 1/10WR607 1-216-814-11 METAL CHIP 270 5% 1/10WR608 1-216-814-11 METAL CHIP 270 5% 1/10WR610 1-216-857-11 METAL CHIP 1M 5% 1/10WR612 1-216-809-11 METAL CHIP 100 5% 1/10W
R613 1-216-821-11 METAL CHIP 1K 5% 1/10WR615 1-216-809-11 METAL CHIP 100 5% 1/10W
< COMPOSITION CIRCUIT BLOCK >
RB601 1-233-810-21 RES, NETWORK 100K (3216)RB602 1-233-810-21 RES, NETWORK 100K (3216)RB603 1-233-810-21 RES, NETWORK 100K (3216)RB604 1-233-810-21 RES, NETWORK 100K (3216)
< VARIABLE RESISTOR >
RV201 1-223-834-11 RES, ADJ, CARBON 47K
< SWITCH >
SW201 1-529-565-41 SWITCH, PUSH (1 KEY) (MAGAZINE DETECT)
< VIBRATOR >
X101 1-795-577-21 VIBRATOR, CERAMIC (16.9344MHz)X201 1-767-133-21 VIBRATOR, CERAMIC (12.288MHz)
**************************************************************
* A-3326-947-A RF BOARD, COMPLETE********************
< CAPACITOR >
C101 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC102 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC103 1-164-156-11 CERAMIC CHIP 0.1uF 25VC104 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC105 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C106 1-164-156-11 CERAMIC CHIP 0.1uF 25VC107 1-164-156-11 CERAMIC CHIP 0.1uF 25VC108 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC109 1-164-156-11 CERAMIC CHIP 0.1uF 25VC111 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C121 1-126-206-11 ELECT CHIP 100uF 20% 6.3VC122 1-164-156-11 CERAMIC CHIP 0.1uF 25VC201 1-117-681-11 ELECT CHIP 100uF 20% 16VC202 1-164-156-11 CERAMIC CHIP 0.1uF 25VC203 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C204 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC205 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC206 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC207 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC208 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C209 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC217 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< CONNECTOR >
CN102 1-778-303-21 CONNECTOR, FPC (ZIF) 16P
< CONNECTOR >
CNJ101 1-778-777-21 CONNECTOR, FPC 26P
< IC >
IC101 8-752-089-74 IC CXA2581N-T4IC201 8-759-832-99 IC LA6576L-TE-L
< TRANSISTOR >
Q101 8-729-010-05 TRANSISTOR MSB709-RT1Q102 8-729-024-88 TRANSISTOR MUN2212T1
< RESISTOR >
R101 1-216-801-11 METAL CHIP 22 5% 1/10WR102 1-216-837-11 METAL CHIP 22K 5% 1/10WR103 1-216-837-11 METAL CHIP 22K 5% 1/10WR104 1-216-845-11 METAL CHIP 100K 5% 1/10WR105 1-216-801-11 METAL CHIP 22 5% 1/10W
R106 1-216-864-11 SHORT CHIP 0R107 1-216-845-11 METAL CHIP 100K 5% 1/10WR108 1-216-833-11 METAL CHIP 10K 5% 1/10WR109 1-216-836-11 METAL CHIP 18K 5% 1/10WR110 1-216-834-11 METAL CHIP 12K 5% 1/10W
R111 1-216-835-11 METAL CHIP 15K 5% 1/10WR112 1-216-845-11 METAL CHIP 100K 5% 1/10WR113 1-218-859-11 METAL CHIP 3.3K 0.5% 1/10WR116 1-216-833-11 METAL CHIP 10K 5% 1/10WR117 1-216-833-11 METAL CHIP 10K 5% 1/10W
R120 1-218-879-11 METAL CHIP 22K 0.5% 1/10WR121 1-218-847-11 METAL CHIP 1K 0.5% 1/10WR122 1-218-847-11 METAL CHIP 1K 0.5% 1/10WR201 1-216-826-11 METAL CHIP 2.7K 5% 1/10WR202 1-216-833-11 METAL CHIP 10K 5% 1/10W
R203 1-216-833-11 METAL CHIP 10K 5% 1/10WR204 1-216-839-11 METAL CHIP 33K 5% 1/10WR205 1-216-833-11 METAL CHIP 10K 5% 1/10WR206 1-216-839-11 METAL CHIP 33K 5% 1/10WR207 1-216-833-11 METAL CHIP 10K 5% 1/10W
R208 1-216-839-11 METAL CHIP 33K 5% 1/10WR209 1-216-833-11 METAL CHIP 10K 5% 1/10WR210 1-216-839-11 METAL CHIP 33K 5% 1/10WR211 1-216-833-11 METAL CHIP 10K 5% 1/10WR212 1-216-839-11 METAL CHIP 33K 5% 1/10W
R213 1-216-833-11 METAL CHIP 10K 5% 1/10WR214 1-216-839-11 METAL CHIP 33K 5% 1/10WR215 1-216-841-11 METAL CHIP 47K 5% 1/10WR216 1-216-842-11 METAL CHIP 56K 5% 1/10WR218 1-216-841-11 METAL CHIP 47K 5% 1/10W
R219 1-216-843-11 METAL CHIP 68K 5% 1/10WR220 1-216-834-11 METAL CHIP 12K 5% 1/10WR222 1-216-821-11 METAL CHIP 1K 5% 1/10WR223 1-216-819-11 METAL CHIP 680 5% 1/10W
MAIN RF
Ver 1.1
53
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
CDX-565MXRF
< SWITCH >
SW1 1-529-566-31 SWITCH, PUSH (1 KEY)(CHUCKING END DETECT)
SW2 1-529-566-31 SWITCH, PUSH (1 KEY) (SAVE END DETECT)**************************************************************
MISCELLANEOUS**************
5 1-823-973-12 CORD (WITH CONNECTOR) (POWER)6 A-3301-964-A RELAY BOX ASSY7 1-792-045-21 CORD (WITH CONNECTOR) (ANT-OUT)
(for RELAY BOX ASSY)8 1-792-044-23 CORD (WITH CONNECTOR) (CD-OUT)
(for RELAY BOX ASSY)9 A-3220-842-A WIRED COMMANDER (RM-X83RF)
10 1-823-920-22 CABLE WITH CONNECTOR 8P (for RM-X83RF)56 1-676-735-11 FM FLEXIBLE BOARD251 1-676-341-11 OP FLEXIBLE BOARD
0255 8-820-103-11 OPTICAL PICK-UP KSS-720A/C-RPF1 1-532-731-11 FUSE (BLADE TYPE) (AUTO FUSE) (3A/32V)
M101 A-3315-151-A SLED MOTOR ASSY (251)M102 A-3301-998-A SPINDLE MOTOR (S) SUB ASSYM103 A-3301-123-A ELJ MOTOR ASSY (CHUCKING)M104 A-3301-123-A ELJ MOTOR ASSY (ELEVATOR)RV202 1-227-137-11 RES, VAR, SLIDE 10K
(ELEVATOR HEIGHT SENSOR) ************************************************************
ACCESSORIES************
1-477-262-12 WIRELESS REMOTE COMMANDER(RM-X84RF)
3-230-047-01 BATTERY HOLDER (for RM-X84RF)3-241-726-12 MANUAL, INSTRUCTION (ENGLISH, FRENCH)3-241-727-11 MANUAL, INSTRUCTION, INSTALL
(ENGLISH, FRENCH)A-3301-944-A MAGAZINE (250) ASSY
************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS**************************************
501 3-040-583-21 BRACKET (T)* 502 X-3369-824-1 SCREW ASSY
503 not supplied504 4-916-258-01 TAPE, MAGIC (for RM-X84RF)505 1-823-973-12 CORD (WITH CONNECTOR) (POWER)
506 A-3301-964-A RELAY BOX ASSY507 1-792-045-21 CORD (WITH CONNECTOR) (ANT-OUT)
(for RELAY BOX ASSY)508 1-792-044-23 CORD (WITH CONNECTOR) (CD-OUT)
(for RELAY BOX ASSY)509 A-3220-842-A WIRED COMMANDER (RM-X83RF)510 1-823-920-22 CABLE WITH CONNECTOR 8P (for RM-X83RF)
F1 1-532-731-11 FUSE (BLADE TYPE) (AUTO FUSE) (3A/32V)
501 502
+PSW4 × 10× 4
TAPPING SCREW(DIA.5 × 20) × 4
BRACKET (T)× 2
503 504
TAPE (COMMANDER)× 1
MAGIC TAPE × 1
505
POWER CORD × 1506
RELAY BOX ASSY × 1
507ANT-OUT CORD
× 1
508CD-OUT CORD
× 1
F1
SCREW ASSY
510
509
WIRED COMMANDER (RM-X83RF) × 1
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
RFVer 1.1
CDX-565MXRF
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.
Ver. Date Description of Revision
1.0 2002.04 New
1.1 2002.06 Correction of Part No. for D701, R311 of FM boardCorrection of Part No. for R216, R413, R414 of MAIN boardCorrection of Part No. for CORD (WITH CONNECTOR) (CD-OUT)(for RELAY BOX ASSY) (ENG-02007)