CERTIFICATEConformity of the Factory Production Control

0036-CPR-1090-1.00641.TÜV SÜD.2017.001In compliance with Regulation 305/2011/EU of the

European Parliament and of the Council of 9 March 2011 (the Construction ProductsRegulation or CPR), this certificate applies to the following construction product:

Construction product Structural components and kits for steel structuresto EXC2 according to EN 1090-2

Intended use for load-bearing structures in all types of buildings

CE – marking method ZA.3.2 and ZA.3.4 acc. to EN 1090-1:2009+A1:2011

produced by or for

Manufacturer RAZVOJ d.o.o., BraslovceMale Braslovce 13a3314 BraslovceSLOVENIA

Manufacturing plantProduction facility of the manufacturer

RAZVOJ d.o.o., BraslovceMale Braslovce 13a3314 BraslovceSLOVENIA

Confirmation This certificate attests that all provisions concerning theassessment and verification of constancy of performancedescribed in Annex ZA of the harmonised standardEN 1090-1:2009+A1:2011under system 2+ are applied, and that the factoryproduction control fulfills all the prescribed requirementsstated therein.

Date of issue 30.08.2017

NextSurveillance audit 30.08.2018

Period of validity This certificate will remain valid as long as the test methodsand/or the factory production control requirements includedin the harmonised standard used to assess the performance of thedeclared characteristics do not change, and the product and themanufacturing conditions in the plant are not modified significantly.

Remarks see reverse

Place and date of issue Munich, 30.08.2017Krepek

Dipl.-Ing. (FH) Steidl Head of certification body

EQ2779663 TÜV SÜD Industrie Service GmbH, Westendstr. 199, 80686 Munich, Germany

Notified Body, No. 0036

Certificate number: 0036-CPR-1090-1.00641.TÜV SÜD.2017.001

Remarks The Notified Body - 0036 TÜV SÜD Industrie Service GmbH has performed theinitial inspection of the/of manufacturing plant(s) and of the factory productioncontrol and performs the continuous surveillance, assessment and approval ofthe factory production control.

This certificate remains valid during the aforementioned period and as long asthe conditions lay down in the above mentioned technical specifications inreference or the manufacturing conditions in the factory itself are not modifiedsignificantly.Upon successful completion of the next continuous surveillance, a newcertificate will be issued.

General provisions

The regulations as addressed in the below listed documents in their respective relevant version shallapply:a) General Terms and Conditions of Business of TÜV SÜD Industrie Service GmbHb) Testing and Certification Regulations of TÜV SÜD Groupc) Certification Contract between TÜV SÜD Industrie Service GmbH and the customer (manufacturer) as

named in the certificated) DVS Guideline 1711 of the German Society of Welding (the guideline shall generally apply except Annex

B) e) General provisions/ conditions for validity of Factory Production Control Certificates according to EN

1090-1 and of the associated Welding Certificates (Request of Certification, Annex 1 of Doc.-No.QS/PÜZ0005/AT)

Welding CertificateTÜV SÜD-00641.2017.001

in accordance with EN 1090-1, table B.1, its hereby declared:The manufacturer has produced evidence that he fulfills the requirements of the European

standard EN 1090-2 for execution of structural steel components

Manufacturer RAZVOJ d.o.o., BraslovceMale Braslovce 13a3314 BraslovceSLOVENIA

Technical specification EN 1090-2:2008+A1:2011

Execution class(es) EXC2 according to EN 1090-2

Welding Process(es)(Reference no. acc. to DIN EN ISO 4063)

111 - Manual metal arc welding135 - Metal active gas welding141 - TIG gas tungsten arc welding

Material Group 1.1, 1.2according to CEN ISO/TR 15608 and EN 1090-2, table 2 and 3

Responsible WeldingCoordinator(Title, Surname, Name, Qualification,Date of birth)

Franc Puncuh, IWE born on: 27.08.1967

Substitute(Title, Surname, Name, Qualification,Date of birth)

Marjan Remic born on: 23.10.1966

Confirmation All provisions concerning welding as described in the above mentionedtechnical specification(s) were applied.

Validity start 30.08.2017

Period of validity 30.08.2018

Remarks see reverse

Place and date of issue Munich, 30.08.2017Krepek/KS

Dipl.-Ing. (FH) Steidl Head of certification body

EQ2779663 TÜV SÜD Industrie Service GmbH, Westendstr. 199, 80686 Munich, Germany

Notified Body, No. 0036

Certificate number: TÜV SÜD-00641.2017.001

Remarks:

Upon succsessful completion of the next continuous surveillance, a new certificate will be issued.All other relevant data are detailed in our report R-TSS-IS-17-11402.

General provisions1. The regulations as addressed in the below listed documents in their respective relevant version shall

apply:a) General Terms and Conditions of Business of TÜV SÜD Industrie Service GmbHb) Testing and Certification Regulations of TÜV SÜD Groupc) Certification Contract between TÜV SÜD Industrie Service GmbH and the customer (manufacturer) as

named in the certificated) DVS Guideline 1711 of the German Society of Welding (the guideline shall generally apply except

Annex B) e) General provisions/ conditions for validity of Factory Production Control Certificates according to EN

1090-1 and of the associated Welding Certificates (Request of Certification, Annex 1 of Doc.-No.QS/PÜZ0005/AT)

2. This certificate may be reproduced or published for advertising or other pur-poses only in its entirety.The wording of any marketing publications must not be contradictory to the contents of thiscertificate.

3. The certifying body reserves the right to perform inspections at the company’s premises at any time,without having to give notice and subject to additional charge, in the event of questions arising withregard to the manufacturer’s qualification.

4. This certificate may be withdrawn, amended or modified at any time, with immediate effect andwithout compensation, if the conditions under which it has been issued have changed or if therequirements of this certificate have not been complied with.

5. The certifying body must be notified of following changes:a) new production plant or changes to key production facilities;b) changes in the position of responsible welding coordinator;c) introduction of new welding procedures, new basic materials and corre-sponding WPQRs (welding

procedure qualification records)d) new key production facilities.In the cases referred to above the certifying body will arrange for an inspection to be performed bythe inspection agency.

Distribution:1. Applicant2. File

_____________________ Frank Steidl

CERTIFICATE

TÜV SÜD-W-0667.2017.001

Manufacturer:

RAVZOJ d.o.o. Braslovče Male Braslovče 13a SI – 3314 Braslovče

Plant(s):

Male Braslovče 13a SI – 3314 Braslovče

The above mentioned company fulfils the

standard quality requirements for fusion welding

of metallic materials

according to

EN ISO 3834-3

Contract: 18687383

Valid until: August 2020 Munich, August 30, 2017

EQ2779663 TÜV SÜD Industrie Service GmbH, Westendstr. 199, 80686 Munich, Germany

Certification BodyMaterial and Welding Technology

Annex to certificate

TÜV SÜD-W-0667.2017.001

Page 1 of 2

The following range is certified according to EN ISO 3834-3

Scope of production: - Steel structural engineering - Silos - chimneys - shell boilers

Base material(s): (Group(s)according to EN ISO/TR 15608)

- 1.1, 1.2

Dimension of items: Thickness up to 50 mm, max. length 6,5 m, max. 3500 mm, max. piece weight 30 t

Welding processes: (Process numbers according to EN ISO 4063)

111 Manual metal arc welding 135 MAG welding with solid wire electrode 141 TIG welding with solid filler material (wire / rod)

Welding supervisor: Mr. Franc Punčuh (IWE) Deputy: Mr. Marjan Remic Personnel for non-destructive testing: Responsible: Mr. Franc Punčuh

All other relevant data are detailed in our report no R-TSS-IS-17-11402Rev2. Remarks: None

Annex to certificate

TÜV SÜD-W-0667.2017.001

Page 2 of 2

General Provisions Should one of the named welding and testing supervisors leave the company, or welding and test procedures or important parts of equipment required for these procedures be changed or any of the welding-related quality assurance measures be modified, this must be reported be-forehand to TÜV SÜD Industrie Service GmbH (hereinafter referred to as TÜV SÜD). If neces-sary, TÜV SÜD will initiate a renewed inspection at the company. The same applies to the per-manent discontinuance of welding work. Should there be any doubts pertaining to the qualification of the company, TÜV SÜD shall have the right to inspect the company and to carry out tests at the company at any time without prior notification. This certificate can be withdrawn, amended or modified with immediate effect and without any compensation, if the conditions under which it was issued have changed or if the stipulations and provisions outlined in this certificate or the pertinent report have not been observed. This certificate shall become invalid if the welding supervisor named therein leaves the com-pany. The authorization shall be suspended for as long as the company does not have a recognized responsible welding supervisor and no accepted deputy is on hand. Application for renewal should be submitted to TÜV SÜD at least 2 months prior to expiry of the certificate. Invalid or revoked certificates must be returned immediately to TÜV SÜD. This certificate may only be copied or published in its entirety for advertising and other pur-poses. The text of promotional material may not contradict this certificate.

_____________________ Frank Steidl

CERTIFICATE TÜV SÜD-DG-0667.2017.001

Manufacturer:

RAVZOJ d.o.o. Braslovče Male Braslovče 13a SI – 3314 Braslovče

Plant(s):

Male Braslovče 13a SI – 3314 Braslovče

Inspection according: AD 2000-Merkblatt HP 0, EN 13445-4, EN 13480-4, EN 12953-4, EN ISO 3834-3

The company

-

-

-

has facilities permitting manufacturing and inspection in compli-

ance with the current technical standards,

operates a quality system which guarantees that manufacturing

and inspection of the products stated in our report are in conform-

ity with the technical rules and standards,

employs qualified supervisory and inspection personnel.

The company has the welding suitability for manufacturing pressure

equipment according above mentioned standards.

Independently of this certificate the requirements of the respectively

selected module have to be considered within the framework of man-

ufacturing pressure equipment according to Pressure Equipment Di-

rective 2014/68/EU.

Report no.: R-TSS-IS-17-11402Rev2

Valid until: August 2020

Munich, August 30, 2017

EQ2779663 TÜV SÜD Industrie Service GmbH, Westendstr. 199, 80686 Munich, Germany

Certification BodyMaterial and Welding Technology