CERTIFICATE OF APPROVAL No CF 5158 - Warrington · PDF fileCERTIFICATE No CF 5158 ... Any change to, or deviation from, this specification ... As defined in certificate of approval

CERTIFICATE OF APPROVAL No CF 5158

This is to certify that, in accordance with

TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of

WHITE ALUMINIUM ENTERPRISES L.L.C.

Sector M-21, Mussafah Industrial Area, PO Box 30665, Mussafah, Abu Dhabi, UAE

Tel: +971 2 5500830 Fax: +971 2 5500828

Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions

appended hereto:

______________________________________________________________________________

CERTIFIED PRODUCT TECHNICAL SCHEDULE

Fire Rated Glazed Steel Doors TS12 Hinged or Pivoted Fire Resisting Pedestrian Type Doorsets with Metallic Leaves and Frames

Signed and sealed for and on behalf of CERTIFIRE

Sir Ken Knight Issued: 09 May 2013 Chairman - Management Council Valid to: 08 May 2018 Page 1 of 3

CERTIFICATE No CF 5158 WHITE ALUMINIUM ENTERPRISES L.L.C.

Page 2 of 3 Signed

Issued: 09 May 2013 Valid to: 08 May 2018

FIRE RATED GLAZED DOORSETS

1. This approval relates to the use of the above doorsets in providing a fire resistance of up

to 60 minutes integrity, as defined in BS EN 1634-1: 2008. 2. This certification is designed to demonstrate compliance of the product or system

specifically with Approved Document B (England and Wales), Section 2 of the Technical Standards (Scotland), Technical Booklet E (N. Ireland). If compliance is required to other regulatory or guidance documents there may be additional considerations or conflict to be taken into account.

3. The doors are approved on the basis of: i) Initial type testing. ii) A design appraisal against TS12. iii) Certification of quality management system to ISO 9001: 2008.

iv) Inspection and surveillance of factory production control. v) Audit testing as defined in TS12.

4. The doorsets comprise glazed mild steel door leaves hung within mild steel frames. 5. This approval is applicable to complete doorsets only. 6. This approval is applicable to single-acting, single and double-leaf, latched (and bolted

for double-leaf option) doorsets at leaf dimensions up to those given in Table 1. 7. Hardware items, including closing devices, shall be CERTIFIRE approved or otherwise

as specified in the data sheet. 8. The doorsets shall be mechanically fixed to wall constructions having a fire resistance of

at least the same period as the doorset. 9. This certificate does not include any approval relating to the mechanical requirements of

the doorsets specified in TS12.

CERTIFICATE No CF 5158 WHITE ALUMINIUM ENTERPRISES L.L.C.

Page 3 of 3 Signed

Issued: 09 May 2013 Valid to: 08 May 2018


Table 1. Maximum Permitted Door Leaf Dimensions

Doorset

Configuration

Integrity and Insulation (I2)

(mins)

Maximum Height (mm)

Maximum Width (mm)

Subject to Maximum Area of

(m2)

Single-acting, single-leaf,

latched

30 2706 1140 2.68


latched

60 2593 1093 2.57

Single-acting, double-leaf,

latched and bolted

30 2706 1140 2.68


latched and bolted

60 2593 1093 2.57

10. Doorsets shall be single-acting, single or double leaf. All doorsets shall be latched and for double-leaf doorsets the inactive leaf shall be flush bolted.

11. Labels to the CERTIFIRE design referencing WHITE ALUMINIUM ENT. L.L.C.,

CERTIFIRE and CERTIFIRE Ref. No. CF 5158 shall be affixed to each door in the prescribed position.

12. This approval relates to on-going production. The product and/or its immediate packaging

is identified with the manufacturer’s name, the product name or number, the CERTIFIRE name and mark together with the CERTIFIRE Certificate number (CF 5158) and application where appropriate.

WHITE ALUMINIUM ENTERPRISES L.L.C. Constructional Specification CF 5158

Page 1 of 6 May 2013

CONSTRUCTIONAL SPECIFICATION FOR CERTIFIRE APPROVED FIRE RATED GLAZED DOORSETS

Introduction This document specifies constructional and other details for the Fire Rated Glazed doorsets manufactured by WHITE ALUMINIUM ENTERPRISES L.L.C. and certified by CERTIFIRE under certificate No. CF 5158. Only doors complying with the details of this document may be marked or marketed as CERTIFIRE approved. Any change to, or deviation from, this specification requires the agreement of CERTIFIRE. CERTIFIRE approval is applicable to complete doorsets only. Scope of Approval As defined in certificate of approval No. CF 5158

Drawings Showing Elevation Various Cross Sections through Framing Members



Vertical Section B-B Section C-C

Frame Header and Leaf Profile Section



Leaf Profile Bottom Section

Leaf and Frame Profile (horizontal Section)

Meeting Edges of the Leaf Profile



Frame Profile and Associated Item Specifications:





Glazing Details and Specifications:

Glass

Material Glass

Manufacturer White Aluminium Fabrication

Reference PYRAWHITE E60/EW45

Dimensions 818 x 2093 x 6mm thick glass

Setting Blocks 80 x 5 x 8 (w x h x depth)

Fixing method The glass was placed within the opening over a 80 x 5 x 8 (w x h x depth) Flammi 12 (Gluske) setting blocks after the frame and leaf profiles were installed. The final beading was clipped on after 6mm ceramic tape was placed on either side of the glass perimeter adjacent to the framing profiles. The spacing between the glass and frame were 5 - 6mm @ bottom 3 - 4mm @ vertical 2 - 3mm @ top

Intumescent Glazing Tape

Material Ceramic glazing edge seal

Manufacturer Gluske

Reference Kerafix Flexlit

Dimensions 15 x 5mm (w x thk) (Uncompressed thickness)

Fixing method Compressed between the glazing beads. See drawings for details.

WHITE ALUMINIUM ENTERPRISES L.L.C. Data Sheet CF 5158


CF 5158 DATA SHEET


DATA SHEET

1. General

These doorsets have been fire tested and certified by CERTIFIRE as being capable of providing fire resistance of up to 60 minutes integrity, for the single-acting configurations, as defined in BS EN 1634-1: 2008, when installed in accordance with the following conditions. In recognition of this, the leaf carries a prefixed label on the top or hanging edge of the door, issued under the terms of the CERTIFIRE scheme. This label uniquely identifies the door leaf, the manufacture of which complies with BS: ISO 9001:2008 for quality systems and is subject to on-going surveillance. This label shall not be removed. It is emphasised that the certification is conditional upon the following instructions being complied with in their entirety. Failure to do so will invalidate this approval and may jeopardise the fire performance of the door. Door assemblies supplied pre-fitted with components by WHITE ALUMINIUM ENTERPRISES L.L.C. may be considered to meet the requirements in respect of those items.

2. Door Leaf Dimensions

The doorsets may be used in single-acting, single or double-leaf, latched (and bolted for double-leaf options), metal framed, metal leaf configurations. The doorsets shall be of mild steel, uninsulated framed glazed construction. The maximum door leaf dimensions are given in Table 1.

Table 1. Maximum Permitted Door Leaf Dimensions

Doorset

Configuration

Integrity and Insulation (I2)

(mins)

Maximum Height (mm)

Maximum Width (mm)

Subject to Maximum Area of

(m2)


latched

30 2706 1140 2.68


latched

60 2593 1093 2.57


latched and bolted

30 2706 1140 2.68


latched and bolted

60 2593 1093 2.57



Supporting Construction The door assemblies are approved to be installed into reinforced concrete or masonry with a

fire resistance at least equal to that of the doorset to be installed.

4. Installation Frame jambs fixed at four equidistant positions. Single-leaf doorset head members to have a

minimum of 1 no. fixing on widths over 900 mm. Double-leaf doorset head members to have 2 no. fixings.

For masonry or concrete, doorset to be installed using steel anchor bolts minimum 10 mm diameter by 100 mm long

5. Seals

Any seals shall be CERTIFIRE approved for use on uninsulated steel doorsets.

6. Hinges

Hinges shall be of steel construction and shall be CE marked for use on fire resisting steel doors. Alternatively, the door may be hung on the specific hinges detailed below:

Number: 2 hinges up to 2295 mm high, 3 hinges over 2295 mm high Reference: Forster 907662

Any other CERTIFIRE approved hinges subject to the conditions contained within the relevant certificate.

7. Lock and Latches

Locks and latches shall be CE Marked for use on fire resisting steel doors, in addition to the following specifications:

Alternative locks/latches which have been CERTIFIRE approved for use in steel doorsets are deemed to be suitable for use.

No restriction on type of metallic lever handles. Locks or latches must be fitted to single-leaf doorsets and the active leaf of double-leaf doorsets.

Specific alternative lock and associated components as detailed below are also included in this scope of approval: Door Lock Manufacturer: Forster Reference: 907233 Dimensions: 45 mm wide by 190 mm high Handles Manufacturer: Forster Reference: 907351 Dimensions: 28 mm wide by 320 mm high



8. Self Closing Devices

A self-closing device is required to be fitted to satisfy fire regulations and if fitted shall be a CERTIFIRE approved and CE Marked product for the required application and door type. Note: closers with mechanical hold-open mechanisms are not permitted to be used.

9. Bolts

Flush bolts or shoot bolts of all steel construction must be fitted to the inactive door leaf of any double-leaf doorset. The inactive door leaf shall incorporate such a bolting device at both the head and base of the leading edge which shall provide at least 10 mm engagement. Specific alternative bolts as detailed below are also included in this scope of approval: Manufacturer: Merit Dimensions: 25 mm wide by 173 mm high

10. Glazed Apertures

All apertures to be factory prepared by WHITE ALUMINIUM ENTERPRISES L.L.C..

Doorsets to be glazed (where r) using an alternative CERTIFIRE approved system (glass and glazing gasket). The relevant system shall be approved for use within an uninsulated steel door construction. The maximum opening or pane dimensions specified within the CERTIFIRE approval for the glazing system shall not be exceeded regardless of the maximum leaf dimensions permitted in this approval. Should a door leaf be required with glazed aperture dimensions that exceed that approved the glass to be used, then the door leaves may incorporate transoms to reduce the aperture dimension. Additionally, any edge cover and/or expansion allowance requirements specified by the glass approval MUST be complied with. Failure to comply with such requirements may invalidate this approval.

A list of approved and acceptable glass types can be found at the following weblink: http://www.warringtonfire.net/certifire/products/glass-and-glazing.html

11. Further Information

Further information regarding the details contained in this data sheet may be obtained from

WHITE ALUMINIUM ENTERPRISES L.L.C.. (Tel: + 971 2 5500830).

Further information regarding the CERTIFIRE certification and other approved products can be obtained from CERTIFIRE (Tel: + 44 (0)1925 646777).

http://www.warringtonfire.net/certifire/products/glass-and-glazing.html

Documents

CERTIFICATE OF APPROVAL No CF 5158 - Warrington · PDF fileCERTIFICATE No CF 5158 ... Any change to, or deviation from, this specification ... As defined in certificate of approval