2
《热科学学报》2017 年文章目录 序号 标题 第一作者 关键词 出版年 / 卷号 / 期号 / 页码 学科方向 1 Modeling and Numerical Investigation of the Inlet Circumferential Fluctuations of Swept and Bowed Blades Tang, M. Z. Throughflow model; Circumferential fluctuation (CF) stresses 2017, 26(1): 1-10 气动 2 Effect of Double Air Injection on Performance Characteristics of Centrifugal Compressor Hirano, T. Centrifugal Compressor; Performance; Nozzle Injection 2017, 26(1): 11-17 气动 3 Numerical Study of Unsteady Flows with Cavitation in a High-Speed Micro Centrifugal Pump Li, Y. Q. Micro-centrifugal pump; Unsteady flow; Cavitation 2017, 26(1): 18-24 气动 4 Numerical Investigation of the Bowed Stator Effects in a Transonic Fan at Low Reynolds Number Huang, E. L. Transonic Fan; Low Reynolds Number; Bowed Stator 2017, 26(1): 25-29 气动 5 Influence of Tip End-plate on Noise of Small Axial Fan Mao, H. Y. Tip end-plate; Small axial flow fan; Noise 2017, 26(1): 30-37 气动 6 Coexisting State of Surge and Rotating Stall in a Two-Stage Axial Flow Compressor using a Double-Phase- Locked Averaging Technique Sakata, Y. Axial flow compressor; Rotating stall; Surge 2017, 26(1): 38-46 气动 7 Statistical Characteristics of Suction Pressure Signals for a Centrifugal Pump under Cavitating Conditions Li, X. J. Centrifugal pump; Cavitation; Suction Pressure 2017, 26(1): 47-53 气动 8 Stereoscopic PIV Measurements of the Flow Field in a Turbine Cascade Tian, Y. T. Stereoscopic PIV; turbine cascade; tip leakage vortex 2017, 26(1): 89-95 气动 9 Effects of Bending-torsional Duct- induced Swirl Distortion on Aerodynamic Performance of a Centrifugal Compressor Hou, H. J. bending-torsional duct; centrifugal compressor; swirl distortion 2017, 26(2): 97-106 气动 10 Measurement and Numerical Simulation of a Small Centrifugal Compressor Characteristics at Small or Negative Flow Rate Tsukamoto, K. centrifugal compressor; turbocharger; measurement; CFD 2017, 26(2): 107-112 气动 11 Experimental Study of Improved HAWT Performance in Simulated Natural Wind by an Active Controlled Multi-Fan Wind Tunnel Toshimitsu, K. Wind Turbine; Wind Energy; Natural-Wind; 2017, 26(2): 113-118 气动 12 Numerical Investigation of the Effects of ITD Length on Low Pressure Nozzle Liu, G. Intermediate Turbine Duct; Length; Nozzle; Pressure Loss 2017, 26(3): 199-207 气动 13 Study of Unsteady Flow Simulation of Backward Impeller with Non-uniform Casing Swe, W. W. M. Centrifugal fan; Impeller; Blade outlet angles 2017, 26(3): 208-213 气动 14 Liquid Phase Evaporation on the Normal Shock Wave in Moist Air Transonic Flows in Nozzles Dykas, S. moist air; condensation; transonic flow 2017, 26(3): 214-222 气动 15 Observation of Inception of Sheet Cavitation from Free Nuclei Tsuru, W. Cavitation inception; Sheet cavity; Nuclei distribution 2017, 26(3): 223-228 气动 16 Research on Online Safety Precaution Technology of a High-medium Pressure Gas Regulator Hao, X. J. high-medium pressure gas regulator; improved wavelet packet; harmonic 2017, 26(3): 229-234 气动 17 Numerical study of hydrogen peroxide thermal decomposition in a shock tube Bhatti, M. R. Reaction kinetics; Rate constant; Numerical simulation 2017, 26(3): 235-244 气动 序号 标题 第一作者 关键词 出版年 / 卷号 / 期号 / 页码 学科方向 18 An Experimental Description of the Flow in a Centrifugal Compressor from Alternate Stall to Surge Moenne- Loccoz, V. centrifugal compressor; alternate stall; mild surge 2017, 26(4): 289-296 气动 19 Flow Development Through HP & LP Turbines, Part II: Effects of the Hub Endwall Secondary Sealing Air Flow on the Turbine's Mainstream Flow Hu, J. L. Turbines; Sealing air; Flow pattern 2017, 26(4): 308-315 气动 20 Effects of Airfoil-probe Tubes on the Flow Field of a Compressor Cascade Ma, H. W. airfoil-probe; compressor cascade; installment position 2017, 26(4): 321-330 气动 21 Numerical Investigation of the Effects of Rising Angle on Intermediate Turbine Duct and Nearby Turbines Liu, H. R. Intermediate Turbine Duct; Rising Angle; Flow Field Analysis 2017, 26(5): 421-430 气动 22 Reconstruction Method for Running Shape of Rotor Blade Considering Nonlinear Stiffness and Loads Wang, Y. L. Blade reconstruction; Fluid-structure interaction; Aeroelasticity 2017, 26(5): 431-439 气动 23 Computational Study of Performance Characteristics for Truncated Conical Aerospike Nozzles Nair, P. P. aerospike nozzle; plug nozzle; advanced rocket nozzles 2017, 26(6): 483-489 气动 24 Investigation of Non-Axisymmetric Endwall Contouring in a Compressor Cascade Liu, X. W. Non-axisymmetric endwall contouring; Compressor cascade; Corner 2017, 26(6): 490-503 气动 25 Effect of Inlet Guide Vanes on the Performance of Small Axial Flow Fan Liu, Y. small axial flow fan; inlet guide vanes; static characteristics 2017, 26(6): 504-513 气动 26 Investigation on Multi-objective Performance Optimization Algorithm Application of Fan Based on Response Surface Method and Entropy Method Zhang, L. small fan; response surface method; entropy method 2017, 26(6): 533-539 气动 27 Influence of Internal Channel Geometry of Gas Turbine Blade on Flow Structure and Heat Transfer Szwaba, R. cooling; internal blade channels; aerodynamics with heat transfer 2017, 26(6): 514-522 气动、传 28 Solution of Inverse Heat Conduction Problem using the Tikhonov Regularization Method Duda, P. inverse problems; heat conduction; identification 2017, 26(1): 60-65 传热 29 Interaction of Two Cavitation Bubbles in a Tube and its Effects on Heat Transfer Liu, B. Cavitation; Interaction effects; Bubble dynamics; Heat transfer 2017, 26(1): 66-72 传热 30 Influence of Filling Ratio and Working Fluid Thermal Properties on Starting up and Heat Transferring Performance of Closed Loop Plate Oscillating Heat Pipe with Parallel Channels Shi, W. X. closed loop with parallel channels; plate pulsating heat pipe 2017, 26(1): 73-81 传热 31 An Analysis of the Numerical Model Influence on the Ground Temperature Profile Determination Jaszczur, M. heat transfer; ground heat transport; ground temperature profile 2017, 26(1): 82-88 传热 32 Theoretical and Computational Analyses of LNG Evaporator Chidambaram, P. K. LNG Evaporator; Analytical Calculation; Numerical Simulation 2017, 26(2): 132-137 传热 33 Thermal Analysis of Void Cavity for Heat Pipe Receiver under Microgravity Gui, X. H. Heat Pipe Receiver; Phase Change; Void Cavity Distribution 2017, 26(2): 138-143 传热 34 Correlation Analysis of Transient Heat Transfer Characteristics for Air Pre cooling Aggregate Guo, C. H. Air precooling; Aggregate; Transient heat transfer 2017, 26(2): 144-152 传热 35 Laminar Forced Convection from a Rotating Horizontal Cylinder in Cross Flow Chandran, P. Heated rotating cylinder; Non-dimensional rotational velocity; Flow 2017, 26(2): 153-159 传热 序号 标题 第一作者 关键词 出版年 / 卷号 / 期号 / 页码 学科方向 36 Experimental studies on the thermal performance of a parabolic dish solar receiver with the heat transfer fluids SiC plus water nano fluid and water Rajendran, D. R. Direct Normal Irradiation; cavity receiver; heat transfer fluids 2017, 26(3): 263-272 传热 37 The Effect of Heating Direction on Flow Boiling Heat Transfer of R134a in Micro-channels Xu, M. C. top heating; bottom heating; flow boiling 2017, 26(2): 166-174 传热 38 Effects of Supercritical Environment on Hydrocarbon-fuel Injection Shin, B. Decane; Jet; Subcritical; Supercritical 2017, 26(2): 183-191 传热 39 Simple Power-type Heat Transfer Correlations for Turbulent Pipe Flow in Tubes Taler, D. Convective heat transfer coefficient; Turbulent tube flow 2017, 26(4): 339-348 传热 40 A Review on Lithium-ion Power Battery Thermal Management Technologies and Thermal Safety An, Z. J. Lithium-ion battery; Heat generation; Thermal management 2017, 26(5): 391-412 传热 41 Film Cooling Performance of a Row of Dual-fanned Holes at Various Injection Angles Li, G. C. gas turbine; film cooling; dual-fanned hole 2017, 26(5): 453-458 传热 42 Numerical Analysis of Microholes Film/Effusion Cooling Effectiveness Ochrymiuk, T. turbulet heat flux; two-equation model 2017, 26(5): 459-464 传热 43 Thermal Analysis of Underground Power Cable System Rerak, M. thermal analysis; power cable; soil 2017, 26(5): 465-471 传热 44 Role of a Single Shield in Thermocouple Measurements in Hot Air Flow Ma, H. W. single-shield; bare- bead thermocouples; temperature measurement 2017, 26(6): 523-532 传热 45 Inverse Problem and Variation Method to Optimize Cascade Heat Exchange Network in Central Heating System Zhang, Y. District heating; Heat exchanger 2017, 26(6): 545-551 传热 46 Inverse Heat Conduction Estimation of Inner Wall Temperature Fluctuations under Turbulent Penetration Guo, Z. C. IHCP; SDM; Temperature fluctuations 2017, 26(2): 160-165 燃烧 47 Tomographic Data Fusion with CFD Simulations Associated with a Planar Sensor Liu, J. Process tomography; data fusion; EV burner 2017, 26(2): 175-182 燃烧 48 Modelling of the Process of Coal Dust Combustion in a Cyclone Furnace Zarzycki, R. oxy-fuel combustion; numerical simulations; coal dust 2017, 26(2): 192-198 燃烧 49 Hydrodynamics in a circulating fluidized bed with annular furnace and six parallel cyclones Shuai, D. P. Circulating fluidized bed; annular furnace; parallel cyclones 2017, 26(3): 273-281 燃烧 50 A new method of thermal protection by opposing jet for a hypersonic aeroheating strut Qin, J. thermal protection; scramjet strut; opposing jet 2017, 26(3): 282-288 燃烧 51 Numerical Study of Effect of Compressor Swirling Flow on Combustor Design in a MTE Mu, Y. Combustor; CFD; Compressor exit flow angle 2017, 26(4): 349-354 燃烧 52 Thermal Analysis and Kinetics of Coal during Oxy-Fuel Combustion Kosowska- Golachowska, M. oxy-fuel combustion; pyrolysis; bituminous coal 2017, 26(4): 355-361 燃烧 53 Physicochemical Properties and Gasification Reactivity of the Ultrafine Semi-char derived from a Bench-scale Fluidized Bed Gasifier Zhang, Y. K. fluidized bed; semi- char; physicochemical properties 2017, 26(4): 362-370 燃烧 54 Experimental Study on Structural Optimization of a Supercritical Circulating Fluidized Bed Boiler with an Annular Furnace and Six Cyclones Wang, X. F. circulating fluidized bed; annular furnace; parallel cyclones 2017, 26(5): 472-482 燃烧 55 Weighted Sum of Gray Gases Model Optimization for Numerical Investigations of Processes inside Pulverized Coal-Fired Furnaces Crnomarkovic, N. Furnace; Numerical simulation; Significant figure 2017, 26(6): 552-559 燃烧

《热科学学报》2017年文章目录jts.iet.cn/static/journals/69/ckeditor_file...Rotating Horizontal Cylinder in Cross Flow Chandran, P. Heated rotating cylinder; Non-dimensional

  • Upload
    others

  • View
    2

  • Download
    0

Embed Size (px)

Citation preview

Page 1: 《热科学学报》2017年文章目录jts.iet.cn/static/journals/69/ckeditor_file...Rotating Horizontal Cylinder in Cross Flow Chandran, P. Heated rotating cylinder; Non-dimensional

《热科学学报》2017 年文章目录

序号 标题 第一作者 关键词出版年 / 卷号 /

期号 / 页码学科方向

1Modeling and Numerical Investigation of the Inlet Circumferential Fluctuations

of Swept and Bowed BladesTang, M. Z.

Throughflow model; Circumferential

fluctuation (CF) stresses2017, 26(1): 1-10 气动

2Effect of Double Air Injection on Performance Characteristics of

Centrifugal CompressorHirano, T.

Centrifugal Compressor; Performance; Nozzle

Injection2017, 26(1): 11-17 气动

3Numerical Study of Unsteady Flows with Cavitation in a High-Speed

Micro Centrifugal PumpLi, Y. Q.

Micro-centrifugal pump; Unsteady flow;

Cavitation2017, 26(1): 18-24 气动

4Numerical Investigation of the Bowed Stator Effects in a Transonic Fan at

Low Reynolds Number

Huang, E. L.

Transonic Fan; Low Reynolds Number;

Bowed Stator2017, 26(1): 25-29 气动

5Influence of Tip End-plate on Noise of

Small Axial FanMao, H. Y.

Tip end-plate; Small axial flow fan; Noise

2017, 26(1): 30-37 气动

6

Coexisting State of Surge and Rotating Stall in a Two-Stage Axial Flow Compressor using a Double-Phase-

Locked Averaging Technique

Sakata, Y. Axial flow compressor; Rotating stall; Surge

2017, 26(1): 38-46 气动

7Statistical Characteristics of Suction Pressure Signals for a Centrifugal Pump under Cavitating Conditions

Li, X. J.Centrifugal pump; Cavitation; Suction

Pressure2017, 26(1): 47-53 气动

8Stereoscopic PIV Measurements of the

Flow Field in a Turbine CascadeTian, Y. T.

Stereoscopic PIV; turbine cascade; tip leakage

vortex2017, 26(1): 89-95 气动

9

Effects of Bending-torsional Duct-induced Swirl Distortion on

Aerodynamic Performance of a Centrifugal Compressor

Hou, H. J.bending-torsional duct; centrifugal compressor;

swirl distortion2017, 26(2): 97-106 气动

10

Measurement and Numerical Simulation of a Small Centrifugal Compressor Characteristics at Small or Negative

Flow Rate

Tsukamoto, K.

centrifugal compressor; turbocharger;

measurement; CFD2017, 26(2): 107-112 气动

11

Experimental Study of Improved HAWT Performance in Simulated

Natural Wind by an Active Controlled Multi-Fan Wind Tunnel

Toshimitsu, K.

Wind Turbine; Wind Energy; Natural-Wind;

2017, 26(2): 113-118 气动

12Numerical Investigation of the Effects of ITD Length on Low Pressure Nozzle

Liu, G.Intermediate Turbine

Duct; Length; Nozzle; Pressure Loss

2017, 26(3): 199-207 气动

13Study of Unsteady Flow Simulation of Backward Impeller with Non-uniform

Casing

Swe, W. W. M.

Centrifugal fan; Impeller; Blade outlet angles

2017, 26(3): 208-213 气动

14Liquid Phase Evaporation on the Normal Shock Wave in Moist Air

Transonic Flows in NozzlesDykas, S.

moist air; condensation; transonic flow

2017, 26(3): 214-222 气动

15Observation of Inception of Sheet

Cavitation from Free NucleiTsuru, W.

Cavitation inception; Sheet cavity; Nuclei

distribution2017, 26(3): 223-228 气动

16Research on Online Safety Precaution

Technology of a High-medium Pressure Gas Regulator

Hao, X. J. high-medium pressure gas regulator; improved wavelet packet; harmonic

2017, 26(3): 229-234 气动

17Numerical study of hydrogen peroxide thermal decomposition in a shock tube

Bhatti, M. R.

Reaction kinetics; Rate constant; Numerical

simulation2017, 26(3): 235-244 气动

序号 标题 第一作者 关键词出版年 / 卷号 /

期号 / 页码学科方向

18An Experimental Description of the

Flow in a Centrifugal Compressor from Alternate Stall to Surge

Moenne-Loccoz, V.

centrifugal compressor; alternate stall; mild surge

2017, 26(4): 289-296 气动

19

Flow Development Through HP & LP Turbines, Part II: Effects of the Hub Endwall Secondary Sealing Air Flow on the Turbine's Mainstream Flow

Hu, J. L.Turbines; Sealing air;

Flow pattern2017, 26(4): 308-315 气动

20Effects of Airfoil-probe Tubes on the Flow Field of a Compressor Cascade

Ma, H. W.airfoil-probe; compressor

cascade; installment position

2017, 26(4): 321-330 气动

21Numerical Investigation of the Effects

of Rising Angle on Intermediate Turbine Duct and Nearby Turbines

Liu, H. R.Intermediate Turbine Duct; Rising Angle; Flow Field Analysis

2017, 26(5): 421-430 气动

22Reconstruction Method for Running Shape of Rotor Blade Considering

Nonlinear Stiffness and LoadsWang, Y. L.

Blade reconstruction; Fluid-structure

interaction; Aeroelasticity2017, 26(5): 431-439 气动

23Computational Study of Performance Characteristics for Truncated Conical

Aerospike NozzlesNair, P. P.

aerospike nozzle; plug nozzle; advanced rocket

nozzles2017, 26(6): 483-489 气动

24Investigation of Non-Axisymmetric Endwall Contouring in a Compressor

CascadeLiu, X. W.

Non-axisymmetric endwall contouring; Compressor cascade;

Corner

2017, 26(6): 490-503 气动

25Effect of Inlet Guide Vanes on the

Performance of Small Axial Flow FanLiu, Y.

small axial flow fan; inlet guide vanes; static

characteristics2017, 26(6): 504-513 气动

26

Investigation on Multi-objective Performance Optimization Algorithm Application of Fan Based on Response Surface Method and Entropy Method

Zhang, L.small fan; response

surface method; entropy method

2017, 26(6): 533-539 气动

27Influence of Internal Channel Geometry

of Gas Turbine Blade on Flow Structure and Heat Transfer

Szwaba, R.cooling; internal blade channels; aerodynamics

with heat transfer2017, 26(6): 514-522

气动、传热

28Solution of Inverse Heat Conduction

Problem using the Tikhonov Regularization Method

Duda, P. inverse problems; heat conduction; identification

2017, 26(1): 60-65 传热

29Interaction of Two Cavitation Bubbles in a Tube and its Effects on Heat

TransferLiu, B.

Cavitation; Interaction effects; Bubble dynamics;

Heat transfer2017, 26(1): 66-72 传热

30

Influence of Filling Ratio and Working Fluid Thermal Properties on Starting up and Heat Transferring Performance of Closed Loop Plate Oscillating Heat

Pipe with Parallel Channels

Shi, W. X.closed loop with parallel channels; plate pulsating

heat pipe2017, 26(1): 73-81 传热

31An Analysis of the Numerical Model Influence on the Ground Temperature

Profile DeterminationJaszczur, M.

heat transfer; ground heat transport; ground temperature profile

2017, 26(1): 82-88 传热

32Theoretical and Computational Analyses of LNG Evaporator

Chidambaram, P. K.

LNG Evaporator; Analytical Calculation; Numerical Simulation

2017, 26(2): 132-137 传热

33Thermal Analysis of Void Cavity for Heat Pipe Receiver under Microgravity

Gui, X. H.Heat Pipe Receiver; Phase Change; Void Cavity Distribution

2017, 26(2): 138-143 传热

34Correlation Analysis of Transient Heat Transfer Characteristics for Air Pre

cooling AggregateGuo, C. H.

Air precooling; Aggregate; Transient

heat transfer2017, 26(2): 144-152 传热

35Laminar Forced Convection from a

Rotating Horizontal Cylinder in Cross Flow

Chandran, P.

Heated rotating cylinder; Non-dimensional

rotational velocity; Flow2017, 26(2): 153-159 传热

序号 标题 第一作者 关键词出版年 / 卷号 /

期号 / 页码学科方向

36

Experimental studies on the thermal performance of a parabolic dish solar receiver with the heat transfer fluids SiC plus water nano fluid and water

Rajendran, D. R.

Direct Normal Irradiation; cavity

receiver; heat transfer fluids

2017, 26(3): 263-272 传热

37The Effect of Heating Direction on

Flow Boiling Heat Transfer of R134a in Micro-channels

Xu, M. C.top heating; bottom heating; flow boiling

2017, 26(2): 166-174 传热

38Effects of Supercritical Environment on

Hydrocarbon-fuel InjectionShin, B.

Decane; Jet; Subcritical; Supercritical

2017, 26(2): 183-191 传热

39Simple Power-type Heat Transfer

Correlations for Turbulent Pipe Flow in Tubes

Taler, D.Convective heat transfer coefficient; Turbulent

tube flow2017, 26(4): 339-348 传热

40A Review on Lithium-ion Power Battery Thermal Management

Technologies and Thermal SafetyAn, Z. J.

Lithium-ion battery; Heat generation; Thermal

management2017, 26(5): 391-412 传热

41Film Cooling Performance of a Row of Dual-fanned Holes at Various Injection

AnglesLi, G. C.

gas turbine; film cooling; dual-fanned hole

2017, 26(5): 453-458 传热

42Numerical Analysis of Microholes Film/Effusion Cooling Effectiveness

Ochrymiuk, T.

turbulet heat flux; two-equation model

2017, 26(5): 459-464 传热

43Thermal Analysis of Underground

Power Cable SystemRerak, M.

thermal analysis; power cable; soil

2017, 26(5): 465-471 传热

44Role of a Single Shield in

Thermocouple Measurements in Hot Air Flow

Ma, H. W.single-shield; bare-bead thermocouples;

temperature measurement2017, 26(6): 523-532 传热

45Inverse Problem and Variation Method to Optimize Cascade Heat Exchange Network in Central Heating System

Zhang, Y.District heating; Heat

exchanger2017, 26(6): 545-551 传热

46Inverse Heat Conduction Estimation of Inner Wall Temperature Fluctuations

under Turbulent PenetrationGuo, Z. C.

IHCP; SDM; Temperature fluctuations

2017, 26(2): 160-165 燃烧

47Tomographic Data Fusion with CFD Simulations Associated with a Planar

SensorLiu, J.

Process tomography; data fusion; EV burner

2017, 26(2): 175-182 燃烧

48Modelling of the Process of Coal Dust Combustion in a Cyclone Furnace

Zarzycki, R.oxy-fuel combustion; numerical simulations;

coal dust2017, 26(2): 192-198 燃烧

49Hydrodynamics in a circulating

fluidized bed with annular furnace and six parallel cyclones

Shuai, D. P.Circulating fluidized bed; annular furnace; parallel

cyclones2017, 26(3): 273-281 燃烧

50A new method of thermal protection by opposing jet for a hypersonic

aeroheating strutQin, J.

thermal protection; scramjet strut; opposing

jet2017, 26(3): 282-288 燃烧

51Numerical Study of Effect of Compressor Swirling Flow on Combustor Design in a MTE

Mu, Y.Combustor; CFD;

Compressor exit flow angle

2017, 26(4): 349-354 燃烧

52Thermal Analysis and Kinetics of Coal

during Oxy-Fuel CombustionKosowska-

Golachowska, M.oxy-fuel combustion;

pyrolysis; bituminous coal2017, 26(4): 355-361 燃烧

53

Physicochemical Properties and Gasification Reactivity of the Ultrafine Semi-char derived from a Bench-scale

Fluidized Bed Gasifier

Zhang, Y. K.

fluidized bed; semi-char; physicochemical

properties2017, 26(4): 362-370 燃烧

54

Experimental Study on Structural Optimization of a Supercritical

Circulating Fluidized Bed Boiler with an Annular Furnace and Six Cyclones

Wang, X. F. circulating fluidized bed; annular furnace; parallel

cyclones2017, 26(5): 472-482 燃烧

55

Weighted Sum of Gray Gases Model Optimization for Numerical Investigations of Processes inside Pulverized Coal-Fired Furnaces

Crnomarkovic, N.

Furnace; Numerical simulation; Significant

figure2017, 26(6): 552-559 燃烧

Page 2: 《热科学学报》2017年文章目录jts.iet.cn/static/journals/69/ckeditor_file...Rotating Horizontal Cylinder in Cross Flow Chandran, P. Heated rotating cylinder; Non-dimensional

序号 标题 第一作者 关键词出版年 / 卷号 /

期号 / 页码学科方向

56Dynamic Characteristics of

Hydrocarbon Fuel within the Channel at Supercritical and Pyrolysis Condition

Yu, B.dynamic characteristics; n-Decane; supercritical

2017, 26(6): 560-569 燃烧

57Study on Al2O3 Extraction From

Activated Coal Gangue under Different Calcination Atmospheres

Dong, L.coal gangue; aluminum oxide; calcination and

activation2017, 26(6): 570-576 燃烧

58

Computational Study on the Influence of Number of Threads on the

Performance of Single Screw Pump at High Angular Velocities

Philip, J.Screw pump; Turbulent flow; Angular velocity; EXTRUDER; FLOW

2017, 26(1): 54-59 流体机械

59

Effects of the aspect ratio on the optimal tilting angle for maximum convection heat transfer across air-filled rectangular enclosures differentially heated at sides

Cianfrini, C.Natural convection

in air; Tilted cavity; Differential heating

2017, 26(3): 245-254 流体机械

60

Influence of thermal and solutal Marangoni effects on free surface

deformation in an open rectangular cavity

Zhou, X. M.thermo-solutocapillary convection; rectangular

cavity2017, 26(3): 255-262 流体机械

61

Flow Development through HP & LP Turbines, Part I: Inward Rotating Cavity Flow with Superimposed

Throughflow

Gao, J. H.Turbines; Inward

rotating cavity flow2017, 26(4): 297-307 流体机械

62

Temperature Measurement of Supercooled Droplet in Icing

Phenomenon by means of Dual-luminescent Imaging

Tanaka, M.Icing; Supercooled water droplet; Temperature

measurement2017, 26(4): 316-320 流体机械

63Analysis of 2D Flow and Heat

Transfer Modeling in Fracture of Porous Media

Guo, C. S.Heat and Mass Transfer; Fracture; Porous Media

2017, 26(4): 331-338 流体机械

64Oil Strategies Benefits over Different

Driving Cycles using Numerical Simulation

Sara, H.Thermal management; Hot oil storage; Oil

sump2017, 26(4): 371-377 流体机械

65Prediction of Acoustic Absorption

Performance of a Perforated Plate with Air Jets

Hamakawa, H.

acoustic absorption; perforated plate;

theoretical prediction2017, 26(4): 378-384 流体机械

66Experimental Investigations on Fiber Motion within Rotor Spinning Unit

Jin, Y. Z. rotor spinning unit; rotor cup; transport

channel2017, 26(4): 385-389 流体机械

67

Study on Performance and Flow Field of an Undershot Cross-Flow Water Turbine Comprising Different Number

of Blades

Nishi, Y.Water Turbine; Cross-Flow Turbine; Free

Surface2017, 26(5): 413-420 流体机械

68Experimental Study of Operation Performance for Hydrocarbon Fuel Pump with Low Specific Speed

Wu, X. Y.

expansion cycle scramjet; hydrocarbon fuel; turbo-pump;

operation; performance

2017, 26(5): 440-447 流体机械

69Effect of Boundary Layer Trip on Reduction of Jet Noise in Over-

Expanded Nozzle FlowAnyoji, M.

Transonic tones; convergent-divergent nozzle; noise reduction

2017, 26(5): 448-452 流体机械

70Numerical Visualization of Air Intake

Induced by Free Surface VortexPark, Y. K.

free surface vortex; numerical visualization;

curtain wall2017, 26(6): 540-544 流体机械

71Performance Enhancement of a Pump Impeller Using Optimal Design Method

Jeon, S. Y.Regenerative Pump; Efficiency; Impeller

2017, 26(2): 119-124 流体机械

72Heat Capacity and Thermal Expansion

of Water and HeliumPutintsev, N.

M.

heat capacity; thermal expansion coefficient;

isothermal2017, 26(2): 125-131 流体机械

热 科 学 学 报

2017 年文章目录

Journal of Thermal Science

主办单位:中国科学院工程热物理研究所

出版单位:科学出版社、Springer-Verlag

主 编:朱俊强

副 主 编:陈海生

执行主编:张 娜

编辑部地址:北京市海淀区北四环西路 11 号 A103

电 话:010-82545967

邮 箱:[email protected][email protected]

投稿网址:https://mc03.manuscriptcentral.com/jths

期刊订阅:

2019 年定价 100 元 / 册,全年刊期:6 期,全年定价 600 元。

①各地邮局订阅:邮发代号 80-936。

②科学出版社期刊发行部:010-64017032 64017539。

③网上购买:搜淘宝店、微店店铺名称“中科期刊(订阅及销售过刊)”;

或扫描下方二维码:

ISSN 1003-2169 CN 11-2853/O4

IET, CAS Science Press Springer

微信公众号

购买方式 购买方式