CFD-S07CP_988982301

SERVICE MANUAL

Sony CorporationAudio&Video Business GroupPublished by Sony Techno Create Corporation

CFD-S07CP

SPECIFICATIONS

CD RADIO CASSETTE-CORDER9-889-823-012010D04-1© 2010.04

Canadian ModelAEP Model

E ModelAustralian Model

Ver. 1.0 2010.04

CD player sectionSystem Compact disc digital audio systemLaser diode properties Emission duration: Continuous Laser output: Less than 44.6 μW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.)Number of channels 2Frequency response 20 Hz - 20,000 Hz +1/–2 dBWow and fl utter Below measurable limit

Radio sectionFrequency range FM: 87.5 MHz - 108 MHz CND, E92, MX model: AM: 530 - 1,710 kHz AEP, AUS, CET, IT, TH, TW model: AM: 531 - 1,602 kHz E41, AR, SP model: AM: 531 kHz - 1,602 kHz (9 kHz step) 530 kHz - 1,610 kHz (10 kHz step)

CD Section

Model Name Using Similar Mechanism CFD-S05Optical Pick-up Name DA11MMVGP

TC Section

Model Name Using Similar Mechanism CFD-S05Tape Transport Mechanism Type MF-S05V/S05VE

IF (AEP, AUS, CET, IT, TH model) FM: 128 kHz AM: 45 kHzAntennas FM: Telescopic antenna AM: Built-in ferrite bar antenna

Cassette-corder sectionRecording system 4-track 2 channel stereoFast winding time Approx. 150 s (sec.) with Sony cassette C-60Frequency response TYPE I (normal): 80 Hz - 10,000 Hz

GeneralSpeaker Full range: 8 cm (3 1/4 inches) dia., 4 Ω, cone type (2)Outputs Headphones jack (stereo minijack): For 16 Ω - 32 Ω impedance headphonesInput AUDIO IN jack (stereo minijack)

– Continued on next page –

CFD-S07CP

2

NOTES ON CHIP COMPONENT REPLACEMENT• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

FLEXIBLE CIRCUIT BOARD REPAIRING• Keep the temperature of soldering iron around 270 °C during

repairing.• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering

or unsoldering.

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

CAUTIONUse of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radia-tion exposure.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT

The laser diode in the optical pick-up block may suffer electro-static break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts.The fl exible board is easily damaged and should be handled with care.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused on the disc refl ective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

NOTES ON DUALDISCSA DualDisc is a two sided disc product which mates DVD record-ed material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed.

Power output 1.7 W + 1.7 W (at 4 Ω, 10% harmonic distortion)Power requirements For CD radio cassette-corder: 120 V AC, 60 Hz (CND, E92, MX, TW model) 230 V AC, 50 Hz (AEP, E41, AUS, CET, IT model) 220 V AC, 50 Hz (TH model) 220 V AC, 50 Hz (AR model) 230 V AC - 240 V AC, 50 Hz (SP model) 9 V DC, 6 R14 (size C) batteries For remote control: 3 V DC, 2 R03 (size AAA) batteriesPower consumption AC 13 WBattery life

For CD radio cassette-corder:FM recordingSony R14P: approx. 4.5 hSony alkaline LR14: approx. 19 hTape playbackSony R14P: approx. 2.5 hSony alkaline LR14: approx. 13 hCD playbackSony R14P: approx. 1 hSony alkaline LR14: approx. 8 h

Dimensions Approx. 365 mm × 134 mm × 230 mm (w/h/d) (14 3/8 inches × 5 3/8 inches × 9 1/8 inches) (incl. projecting parts)Mass Approx. 2.7 kg (5 lb. 15 oz) (incl. batteries)Supplied accessories AC power cord (1) Remote control (1)

Design and specifi cations are subject to changewithout notice.

• Abbreviation AR : Argentina model AUS : Australian model CET : East European & Russian model CND : Canadian model E41 : 230V AC area in E model E92 : 120V AC area in E model EA : Saudi Arabia model IT : Italian model MX : Mexican model SP : Singapore model TH : Thai model TW : Taiwan model

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

CFD-S07CP

3

1. SERVICING NOTES ............................................. 4

2. DISASSEMBLY2-1. Cabinet (Upper) Section ................................................. 62-2. Cabinet (Front) Section ................................................... 62-3. MAIN Board ................................................................... 72-4. POWER Board ................................................................ 72-5. CD Block Assy ................................................................ 82-6. MOTOR Board ............................................................... 82-7. CD Lid ............................................................................ 92-8. MD Block Assy ............................................................... 92-9. Cassette Lid ..................................................................... 102-10. KEY Board ...................................................................... 10

3. MECHANICAL ADJUSTMENTS ...................... 11

4. ELECTRICAL ADJUSTMENTS Tape Section .................................................................... 11 Tuner Section .................................................................. 12 CD Section ...................................................................... 13

5. DIAGRAMS5-1. Block Diagram –CD Section– ........................................ 155-2. Block Diagram –Main Section– ..................................... 165-3. Printed Wiring Board –Main Section– ............................ 185-4. Printed Wiring Boards –Key, Power Section– ................ 195-5. Schematic Diagram –Main Section (1/3)– ...................... 205-6. Schematic Diagram –Main Section (2/3)– ...................... 215-7. Schematic Diagram –Main Section (3/3)– ...................... 225-8. Schematic Diagram –Key Section– ................................ 235-9. Schematic Diagram –Power Section– ............................. 24

6. EXPLODED VIEWS6-1. Overall Section ............................................................... 306-2. Cabinet (Front) Section ................................................... 316-3. Cabinet (Upper) Section (1) ............................................ 326-4. Cabinet (Upper) Section (2) ............................................ 336-5. Cabinet (Rear) Section .................................................... 34

7. ELECTRICAL PARTS LIST .............................. 35

TABLE OF CONTENTSUNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to

about 350 °C.Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!• Strong viscosity Unleaded solder is more viscous (sticky, less prone to fl ow)

than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.

• Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

CFD-S07CP

4

SECTION 1SERVICING NOTES

CHUCK PLATE JIG ON REPAIRING

On repairing CD section, playing a disc without the lid (CD), use Chuck Plate Jig.• Code number of Chuck Plate Jig: X-4918-255-1

LASER DIODE AND FOCUS SEARCH OPERATIONCHECK1. Turn ON the [OPERATE] or [POWER] button and press [CD]

button to CD position.2. Open the CD lid.3. Turn on S801 with screwdriver, etc. as following fi gure.4. Press the [N X] (CD) button.5. Confi rm the laser diode emission while observing the object-

ing lens. When there is no emission, Auto Power Control cir-cuit or Optical Pick-up is broken.

Objective lens moves up and down three times for focus search.

S801

PRECAUTION WHEN INSTALLING A NEW OP UNIT/PRECAUTION BEFORE UNSOLDERING THE STATIC ELECTRICITY PREVENTION SOLDER BRIDGE

When installing a new OP unit, be sure to connect the fl exible printed circuit board fi rst of all before removing the static electric-ity prevention solder bridge by unsoldering. Remove the static electricity prevention solder bridge by unsolder-ing after the fl exible printed circuit board has already been con-nected. (Do not remove nor unsolder the solder bridge as long as the OP unit is kept standalone.)

CFD-S07CP

5

SECTION 2DISASSEMBLY

• This set can be disassembled in the order shown below.

2-1. CABINET (UPPER) SECTION (Page 6)

SET

2-2. CABINET (FRONT) SECTION (Page 6)

2-3. MAIN BOARD (Page 7)

2-4. POWER BOARD (Page 7)

2-10. KEY BOARD (Page 10)

2-5. CD BLOCK ASSY (Page 8)

2-6. MOTOR BOARD (Page 8)

2-8. MD BLOCK ASSY (Page 9)

2-7. CD LID (Page 9)

2-9. CASSETTE LID (Page 10)

CFD-S07CP

6

1 wire (flat type) (5 core) (CN801)

6 cabinet (front) section

cabinet (rear) section

3 CN301(4P)

to MAIN board

Install the wires in the ditch surely.

Attention at the time of the assembling.

2 CN310 (3P)

4 six screws (+BV tapping (B2.6))

5 four screws (+BV tapping (B2.6))

0 wire (flat type) (6 core) (CN808)

qa wire (flat type) (16 core) (CN810)

6 CN317 (5P)

7 CN316 (4P)

9 CN807 (4P)

8 S801 (2P)

2 screw (+BV tapping (B2.6))

3 six screws (+BV tapping (B2.6))

4 two screws (+BV tapping (B2.6))


1 battery case lid

qs cabinet (upper) section

Note: Follow the disassembly procedure in the numerical order given.

2-1. CABINET (UPPER) SECTION

2-2. CABINET (FRONT) SECTION

CFD-S07CP

7

1 CN901 (3P)2 CN1 (2P)

3 three screws (+P tapping (B2.6))

5 MAIN board


4 three screws (+P tapping (B2.6))

1 CN901 (3P)

6 CN903 (2P)

7 POWER board


cabinet (rear) section4 two screws (+BV tapping (B2.6))

5


2-3. MAIN BOARD

2-4. POWER BOARD

CFD-S07CP

8

1 Remove the four solders.

2 MOTOR board

cabinet (upper) section

2-5. CD BLOCK ASSY

2-6. MOTOR BOARD

1 four screws (+PWH tapping (B2.6))

3 two vibration proof rubbers (green)

5 CD cover

6 CD block assy4 two vibration proof rubbers (red)

2


CFD-S07CP

9


2 damper

7 CD lid 34

5

6



3 three screws (+BV tapping (B2.6))

4 MD block assy

2 SWITCH board


2-7. CD LID

2-8. MD BLOCK ASSY

CFD-S07CP

10

2-9. CASSETTE LID

2-10. KEY BOARD


2 damper

6 cassette lid

3

4

5



4



cabinet (front) section

6 four screws

7 three screws

8 KEY board

5 JACK board

CFD-S07CP

11

SECTION 3MECHANICAL ADJUSTMENTS

SECTION 4ELECTRICAL ADJUSTMENTS

• Standard Output LevelOutput terminal HP OUTload impedance 32 Ω

output signal level 0.25 V (–10 dB)

• Test TapeTape Signal Used for

WS-48A 3 kHz, 0 dB tape speed adjustmentP-4-A063 6.3 kHz, –10 dB azimuth adjustment

Tape Speed AdjustmentProcedure:Mode: playback

i jack (J301)

set

32

test tapeWS-48A(3 kHz, 0 dB)

digital frequencycounter

Adjust so that the value on the digital frequency counter is3,000 Hz.

Specifi cation Value:Digital frequency counter

2,910 to 3,090 Hz

Adjust so that the frequency at the beginning and that at the end oftape winding are between 2,910 to 3,090 Hz.

Adjustment Location:

Precaution1. Clean the following parts with a denatured-alcohol-moistened

swab: record/playback head pinch roller erase head rubber belts capstan idlers2. Demagnetize the record/playback head with a head demag-

netizer. (Do not bring the head magnetizer close to the erase head.)

3. Do not use a magnetized screwdriver for the adjustments.4. The adjustments should be performed with the rated power

supply voltage (9 V) unless otherwise noted.

Torque Measurement

Mode Torque meter Meter reading

FWD CQ-102C2.95 – 6.86 mN • m

(30 to 70 g • cm)(0.42 – 0.97 oz • inch)

FWD Back tension CQ-102C

0.15 – 0.53 mN • m(1.5 to 5.5 g • cm)

(0.021 – 0.076 oz • inch)

FF CQ-201Bmore than 5.88 mN • m(more than 60 g • cm)

(more than 0.83 oz • inch)

REW CQ-201Bmore than 5.88 mN • m(more than 60 g • cm)

(more than 0.83 oz • inch)

Tape Tension Measurement

Mode Tension meter Meter reading

FWD CQ-403A more than 100 g(more than 3.53 oz)

TAPE SECTION 0 dB = 0.775V

Tape speed adjustmentcontrol inside motor

CFD-S07CP

12

• AM Section Setting: RADIO BAND•AUTO PRESET button: AM

Put the lead-wireantenna close tothe set.

AM RF signalgenerator

30% amplitudemodulation by400 Hz signal

• FM Section Setting: RADIO BAND•AUTO PRESET button: FM

CN1

FM RF signalgenerator

75 kHz frequencydeviation by 1 kHz signaloutput level : as low as possible

0.01 F

set

• Connecting Level Meter (FM, AM)

i jack (J301)

set

32

level meter(range: 0.5–5 V ac)

AM FREQUENCY COVERAGE CHECK (CND, E92, MX)Frequency Display 530 kHz 1,710 kHzAdjustment Part <confi rmation>

AM FREQUENCY COVERAGE CHECK(EXCEPT CND, E92, MX)

Frequency Display 531 kHz 1,602 kHzAdjustment Part <confi rmation>

FM FREQUENCY COVERAGE CHECKFrequency Display 87.5 MHz 108 MHzAdjustment Part <confi rmation>

• Abbreviation CND : Canadian model E92 : 120V AC area in E model MX : Mexican model

TUNER SECTION 0 dB = 1 μVRecord/Playback Head Azimuth AdjustmentProcedure:Mode: playback

i jack (J301)

set

32

test tapeP-4-A063(6.3 kHz, –10 dB)

Audio level meter

Play back the test tape (P-4-A063) and adjust a screw for Azimuth adjustment in the head right side so that the output becomes maxi-mum. The headphone output level is a range of –7 dB from –15 dB. After the adjustment, apply suitable Locking compound to the part adjusted.

Adjustment Location:

Record/playbackAzimuth adjustment screw

CFD-S07CP

13

CD section adjustments are done automatically in this set.In case of operation check, confi rm that focus bias.

FOCUS BIAS CHECK1. Connect the oscilloscope between IC801 pin ul and pin ik (or

TP804 (RF) and TP711 (VREF)).2. Insert the disc (PATD-012 (Tr 15)). (Part No. : 4-225-203-01)3. Press the N X (CD) button.4. Confi rm that the oscilloscope waveform is as shown in the fi g-

ure below. (eye pattern) A good eye pattern means that the diamond shape (◊) in the

center of the waveform can be clearly distinguished.

• RF signal reference waveform (eye pattern)

RF level :1.5 ± 0.2 Vp-p

VOLT/DIV : 50 mV (10 : 1 probe in use)TIME/DIV : 500 nS

When observing the eye pattern, set the oscilloscope for AC rangeand raise vertical sensitivity.

Test Point:– MAIN BOARD (Conductor Side) –

CD SECTION

EXCEPTCET, IT MODEL

IC801

IC303

IC701

CN808CN802

C126

C227C127

C220

C120

C228C128

C703

C880

C863

C803

L805

CN310

CN810

JW125

JW126

JW129

JW141

JW142

JW149

JW130

JW131

JW107

JW133

JW181

JW157

JW185

W187 JW186

JW188

JW127

JW128

JW137

L807

JW13

6

JW13

9JW14

0

JW14

3

JW18

0

JW12

4

JW12

2

JW12

1

R703

R707

R713

15 21 22 28

1

32 17

16

1 3

14 8 7 1

R705

R706C701

R702

1 5

2 6

1516

C882

C881

C866 C867

C859C854C864

R864R865

R862

R861

R860

R859

R858

R850

R851 R852R853

C851

R863

9C835

R412

JC803

R701

R708

R714

R704

R715

C883 C8

79

C865

C861

C858

C853

C852

C862

FB80

2

C855

R855

C856

R856

C878

C704

R720

R867

R808

R832

C129C231

C131

C130 C230

R326R325

R127

R229

R130R224

R230

R232

R125

C702

R719R124

C322

C323

C229

R228

R128

R132

R123

R225

R223

R129

R126

76

100

50

1

51

75

TP804 (RF)

TP985

TP805

TP711(VREF)

JACKBOARDCN311

C

TP804 (RF)

TP711 (VREF)

CFD-S07CP

14

MEMO

CFD-S07CP

CFD-S07CP

1515

A

B

C

F

E

D

A

B

C

D

LD

PD

VR

F

SL+SL–

SP+SP–

E

VC

LD

PD APC

FNI1 (A)

FNI2 (C)

LDO

MDI

TPI (F)

TNI (E)

PVREF

86

87

71

90

82

FPI2 (D)84

FPI1 (B)85

89

83

201817

24

7

(TIN)

(FIN)

9(SLIN)

3SPIN

VREF

MUTE

T+T-

2627

F+F-

T+T-

F+F-

SL+SL-

SP+SP–

(DA11MMVGP)

M

M

XOXI

LO

RO

TRO

27 28

22

24

CD RF AMP/SERVO CONTROL,AUDIO DAC, DSP

IC801 (1/2)

6

X80116.93MHz

5 CD-LIMIT/LID IN

40 MOTOR-MUTE

BATT

-CHK

-H

38P-

CONT

+6.2V REG.Q954

+3.3V REG.IC802

+B DELAYSWITCHQ952,953

CLOCKSHIFT

SWITCHQ801,802

+BCONTROL

Q951

+BSWITCHQ804,805

TU+3.3V

S801

3.3V

9V (SW)6.2V

+3.3V

J901 AC IN

Signal path : CD

VRO88

1-bit DACANDLPF

DIGITAL EQUALIZER,EFM DECODE, DSP

CLOCKGENERATOR

23

VC

VC

CD-R

CD- L

DIGITALSERVO

CONTROL

RF AMP&

ADC

+3.3V REG.Q955

7

6V C

HK

100

FOO

99

FMO

DMO

1 2

13+1.5V REG.

IC803+1.5V 54

+1.5V REG.IC804+1.5V 54

43

POW

ER K

EY

D951 D952D808

D806

CET,IT MODEL

EXCEPT CET,IT MODEL

BATT

VDD

AC-HI

TRACKINGCOIL

DRIVE

FOCUSCOIL

DRIVE

SLEDMOTORDRIVE

SPINDLEMOTORDRIVE

SLED/SPINDLE MOTOR DRIVE,TRACKING/ FOCUS COIL DRIVE

IC701

M702SLED

MOTOR

M701SPINDLEMOTOR

S701(LIMIT)

PUSHOPEN/CLOSE

TRACKINGCOIL

FOCUSCOIL

LD POWERCONTROLLER

Q701

OPTICAL PICK-UPBLOCK

DRY BATTERYSIZE " C "

(IEC DESIGNATION R14)6PCS, 9V

T901POWER

TRANSFORMERD901 – 904

RECT

F901

F902

MXI 11

10

5655

MXO

D-SHIFT1D-SHIFT2

X8024.19MHz

18RESET

57SEG2

+3.3V+3.3V

D401OPR/BATT

S401OPERATE

POWER

1211

21

A MAINSECTION

SECTION 5DIAGRAMS

5-1. BLOCK DIAGRAM – CD Section –

(Page 16)

CFD-S07CP

CFD-S07CP

1616

SIGNAL PATH: FM

: AM

: PB

: REC

: CD

5

21

24

L-CH

R-CH

HRP301RECORD/PLAYBACK

HEAD

HE301ERASE HEAD

DET

MUTE

ALC 1

18

15

L.LO

R.LO

TAPE

R-CH

CET,IT MODEL

R-CH

R-CH

I2C BUS LOGIC

27

CLK

SDA

SCL

28

DATA

POWER AMPIC302

R-CH

STBY VCC

L-OUTL-IN

R-CH

R-CH

SP101SPEAKER

(L-CH)SP201

SPEAKER(R-CH)

J301

REF

L.LINE

L.RO

REC

T301

J302AUDIO IN

REC BIAS OSCQ301

ISS1

41

FUNC

-TC

17

LCD DRIVER,SYSTEM CONTROL

IC801 (2/2)

REMOT CONTROLRECEIVER

IC401

33 34

EEP-

DAT

EEPROMIC805AUDIO LEVEL

DETECT AMPIC807

KEY2

-I

4

KEY1

-I

3

REC/PBPRE AMP

IC301

6

1 12

2

16R.RAD R-CH

22

20

6

14 R.LINE

R.IN

L.IN

9

8R.RO

A-MU

TE

39

MUTEQ102

M

TAPE PLAYDETECT

Q808

4TA

PE R

EC

46

-1 -2

S301(REC/PB)

REC

PB

KEY2

KEY1SW1

(LEAF SW)

M901CAPSTAN/REEL

MOTOR

S410-416S402-409

181715

TU-D

ATTU

-CLK

TU R

ESET

SDIO

LOUTROUT

SCLKRST

FMI

AMI

2423

EEP-

CLK

AUDI

O IN

CHE

CK

6.2V

Q302

9V(SW)

VDD

9V (SW)

CD-RCD-L

ISS2

42

Q303

KEY NETWORK

VOL IN L

IN L TU

IN L AUIN L CD

ICOUT L

L OUT

INPUT SELECT,ELECTRONIC VOLUME,

TREBLE/BASS CONTROLIC303

13

12

15

25

E-VOLTREBLE/BUSS

CONTROL

L.RAD

43-159 – 12

LIQUID CRYSTAL DISPLAYPANELLCD401

8

12

BROADCASTFM/AM RADIO

RECEIVERIC1

ANT1FM TELESCOPIC

ANTENNA

L1AM

FERRITE-BARANTENNA

SDIO

SCLK RS

T

SDIOSCLK

RST

i

9

353231

45

TC-O

PERA

TION

COM0-3 SEG1-29

3

19

X132.768kHz

GPO3/DCLK

RCLK

R-ch is omitted due to same as L-ch.

CDSECTION A

5

6

CSCS

DATA

DATA

WR

WR

RMC

RD OUTLCD DRIVER

IC806

1 4 3 2

60 61 59

4

44

3

30

1

–AUDIO

DETECTQ803,806

5-2. BLOCK DIAGRAM – MAIN Section –

(Page 15)

CFD-S07CP

CFD-S07CP

1717

For Schematic Diagrams.Note:• All capacitors are in μF unless otherwise noted. (p: pF) 50

WV or less are not indicated except for electrolytics and tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise specifi ed.

• f : Internal component.• C : Panel designation.

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)

• A : B+ Line.• H : Adjustment for repair.• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions. no mark : FM ( ) : AM < > : PB ‹‹ ›› : REC [ ] : CD PLAY• Voltages are taken with VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production

tolerances.• Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production

tolerances.• Circled numbers refer to waveforms.• Signal path. F : FM f : AM E : PB a : REC J : CD• Abbreviation AR : Argentina model AUS : Australian model CET : East European & Russian model CND : Canadian model E41 : 230V AC area in E model E92 : 120V AC area in E model EA : Saudi Arabia model IT : Italian model MX : Mexican model SP : Singapore model TH : Thai model TW : Taiwan model

For Printed Wiring Boards.Note:• X : Parts extracted from the component side.• Y : Parts extracted from the conductor side.• W : Indicates side identifi ed with part number.• f : Internal component.• : Pattern from the side which enables seeing. (The other layers’ patterns are not indicated.)

• Indication of transistor.

C

BThese are omitted.

EQ

B C E

Q

B

These are omitted.

C E

Q

• Circuit Boards Location

• Waveforms

– MAIN Board –

Caution:Pattern face side:(Conductor Side)Parts face side: (Component Side)

Parts on the pattern face side seen from the pattern face are indicated.Parts on the parts face side seen from the parts face are indicated.

Note: The components identi-fi ed by mark 0 or dotted line with mark 0 are criti-cal for safety. Replace only with part number specifi ed.

Note: Les composants identifi és par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le nu-méro spécifi é.


1.0 Vp-p

1 IC1 ql (RCLK)

500 mV/DIV, 10 s/DIV

1.4 Vp-p

1.5±0.2 Vp-p

Approx. 100 mVp-p

4 IC801 ul (RFO)

500 mV/DIV, 0.5 s/DIV

1.6 V

Approx. 200 mVp-p

1.6V

5 IC801 og (FEI)

100 mV/DIV, 5 ms/DIV

– CD PLAY –

– CD PLAY – – TAPE REC –

– TAPE REC –

– TUNER MODE –

– CD PLAY – – CD PLAY –6 IC801 oh (TEI)

200 mV/DIV, 5 ms/DIV

3 IC801 wk (XO)

0.5 V/DIV, 20 ns/DIV

4.0 Vp-p

7 Q301 C (REC)

1 V/DIV, 10 s/DIV

36 Vp-p

8 HRP301 (YEL)

10 V/DIV, 10 s/DIV

18.2 sec

18.2 sec

32.768 kHz

16.93 MHz

3 Vp-p

4.19 MHz

2 IC801 0 (MXO)

1 V/DIV, 0.1 s/DIV

MAIN board

JACK board

SWITCH board

KEY board

POWER boardMOTOR board

RMC board

CFD-S07CP

CFD-S07CP

1818

• : Uses unleaded solder.• See page 17 for Circuit Boards Location.5-3. PRINTED WIRING BOARD – MAIN Section –

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12

MAIN BOARD

1-881-456-

11

(11)

1-881-462-

11

(11)

OPR/BATTD401

ANT1FM TELESCOPIC

ANTENNA

L1AM FERRITE BAR ANTENNA

CET, IT MODEL

CET, IT MODEL

CET, IT MODEL

CET, IT MODEL

EXCEPTCET, IT MODEL

HPR301RECORD/PLAY BACK

HEAD

HE301ERASEHADE

(L-CH)

(R-CH)

i

J301

SP201SPEAKER

(R-CH)

SP101SPEAKER

(L-CH)

OPTICALPICK-UPBLOCK

(DA11MMVGP)

PUSHOPEN/CLOSE

S801

Z

M901(CAPSTAN/RELL MOTOR)

SW1(LEAF SW)

MM

RMC BOARD

IC302

IC803

IC804

IC801

IC805

IC806

IC1

IC301

IC303

IC80

7

IC701

IC80

2

IC401

CN301C244

CN901

CN808CN802

CN807

CN1

L1

L5

X1

C240C144

C953

C950

C324

C18

C221C321

C224C225

C125 C124C303

C301

C102

C302

C202

C330

C304

C408

C226C126

C227C127

C220

C120

C228C128

C703

C880

C877

C891

C896 C893

C863

C803

C834

C403

C804

C819

C814

C821

X801

X802

C959L808

L809

L811

L806

L810

L803

L804

L802

CN313

L805

T301

CN316

CN310

CN810CN801

CN317

C121

Q954 Q955

C957

JW214

B

B

B

EC

CE

C

E

JW168

JW114

JW103

JW104

JW148

JW111

JW113

JW119

JW125

JW126

JW129

JW141

JW142

JW149

JW130

JW131

JW107

JW133

JW181

JW157

JW185

JW187

JW192

JW204

JW179

JW176

JW175

JW105JW174

JW178

JW194

JW195

JW196

JW186

JW188

JW189

JW190

JW191

JW199

JW213

JW127

JW128

JW137

JW160

JW165

JW150

JW166

JW167

JW169

JW170

JW173

JW152

JW154

JW156

JW155

JW171

JW177

C326C311

C239

C238

C139

C138

C898

C890

C888

C141

C145

C329

JW146JW14

7

JW13

2

JW16

1

JW15

1

JW13

5

JW13

4

JW13

8

JW21

5 JW15

9 JW15

8

JW11

5 L2JW

118

JW10

8

JW10

9

JW14

5

JW11

6L807

JW11

2

JW16

2

JW16

3

JW13

6

JW13

9JW14

0

JW14

3

JW18

0

JW11

0

JW19

3JW19

7

JW19

8

JW21

1

JW18

2

JW20

8

JW20

9

JW21

0

JW15

3JW

200

JW20

1

JW20

2

JW20

3

JW20

5

JW20

6

JW20

7

JW18

3

JW12

3

JW12

4

JW12

2

JW12

1

D3 D2

JW21

2

JW10

6

JW10

1

JW16

4

L801

Q952

C243

R241

R888 C958

D951R950R951

R952R953

R239

R236R139

R138R137R136

R145

R140

C142

C892

R703

R707

R713

15 21 22 28

112

13

1

32 17

16

24

1 31

15

4

14

1346

121097

8 7 1

1

112

13 243

4 5

R705

R706C701

R702

C895

D806

D807C886

C8761

1

1

14

3

5

2 6

13

31

5 4

4

1 2 3

5

1 152 16

5

2 4C882

C881

C866 C867

C859C854C864

R864R865

R862

R861

R860

R859

R858

R850

R851 R852R853

C851

R863

C810

C845

R883

R875

R874

R802 R801R803

R836

R804

R877

R878

R879

R891

D801 R810

R813

C823

C829C835

R826R412

R854

C824

R992

R989

R967

R869R870R872R873

JC803R827

R828

R410

C825 R821

R816

R822

C827 R823

R824

R825

FB801

FB80

4

FB80

3

R880

C885

C818C815

C816

R876

C894

R701

R708

R714

R704

R715

C897

C887

R857

R881

Q804

Q701

D808

Q805

R884

R885

R886

C802

C801

C884

C883 C8

79

C865

C861

C858

C853

C852

C862

FB80

2

C855

R855

C856

R856

C878

C704

R720

R868

R867

R808

R812

C813

C841

C850

C812

R815 R8

14

R832

R830

R831

R402R8

33

R889

R407

C961

C962

R409

R829

C831

C832

C833

Q803

Q806

C830

R834

R837 R8

20R8

38

R425

R902

R901

R900

R899

R898

R897

R896

R895

R894

R893

R892

R994

R993

R988R9

87R9

86R9

85R9

84R9

83R9

82R9

81R9

80R9

79R9

78R9

77

R976

R975

R974

R973

R972

R971

R970

R969

D802R8

44

R819

R818

C828

C822

R811

R809

JC80

2

C817

C849

C820

R890

R807

R806

R805

R866

C889

R141

C328

C954

C956

R242

R142

C143

C327

C951

R964 R9

55R9

54 R956

R887

C899

Q808

Q951

R957

R958

C955

D953

D952 D9

54

C7

C16

C237

C325

C236

C122

C223

C129C231

C131

C130 C230

R321R324

R326R325

R226

R127

R229

R420R204 R104 R301

R203

R210 R102

FB207

JC301 C310

C307R307

C308

R308

C203

C104

R414C409

C309

R130R224

R230

R232

R125

C702

R719R124

R302

R351R424

L4 C24

C17

R1

R4

R8

R11

R7

C8

C4

C25

C5C3

C2C1

C10 R6

R134

R320

R234

C235

C320

C322

C323

C234

C137

C406

C229

R423R4

21R228

R128

R132

R123

R225

C405

C404

C305

C105

R304

R202

R315

R305

C306

R306

R314

R310

R311

Q302

Q303

Q301

R207

R110 R1

07R1

03C1

03C1

01

C205

C201

C204

FB20

6

FB20

5

FB20

4

FB20

3

FB20

2

FB20

1

R223

R129

R126 R4

22C4

07JC80

4

JC80

1

C136

C135

C134

R3

R21

C14

C11

C13

C15

R10

C9

C21 C2

2

C312

R309

D1

L6

R959

R960 R9

62

R961

R963

Q953

C242

C245

R238

R245

R350

C140

R237

Q202

Q102

R240

C241C952

LCD401LIQUID CRYSTAL DISPLAY PANEL

11

1

12

22 23

33

34

44

76

100

50

26

25

1

51

75

1

1 2 3

3

41

58

TP804 (RF)

TP985

TP805

TP711(VREF)

BLK

REDYELWHT

RED

RED

WHT

WHT

CN810

RED 1

2

34RED

CN901

CN808

CN801

WHT

WHT

CN312

C963

C964

R426

D401

SWITCHBOARDCN318

DJACK

BOARDCN311

C

MOTORBOARDCN701

E

KEYBOARDW401

A

POWERBOARDCN902

B(Page 19)

(Page 19)

(Page 19)

(Page 19) (Page 19)

CFD-S07CP

CFD-S07CP

1919

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

KEY BOARD

POWER BOARD

MOTOR BOARD

SWITCH BOARD

JACK BOARDVOLUME

+

>/PRESET +

./PRESET –

VOLUME–

/TUNE–

/TUNE+

RADIO BAND/AUTO PRESET

DISPLA /ENTER MEMORMEGA BASS

AUDIO IN CD TAPE MODE OPERATE (CET, IT)

(EXCEPT CET, IT)OPERATE

1-881-459-

11

(11)

x u

AUDIO INJ302

1-881-457-

11

(11)

NOT REPLACEABLEBUILT IN TRANSFORMER

1-881-458-

11

(11)

- AC IN

DR BATTERSIZE “C”

(IEC DESIGNATION R14)6pcs, 9V

+

–BLK

WHT

1-881-461-

11

(11)

S701(LIMIT)

M701(SPINDLE MOTOR)

M702(SLED MOTOR)

MM

MM

S301(REC/PB)

REC

PB

1-881-460-

11

(11)

MAINBOARDCN801

A

MAINBOARDCN310

C

MAINBOARDCN901

B

MAINBOARDCN808

E

MAINBOARDCN317

D

JW70

1

S701

J302

CN311

C132C232

C233

C133

FB21

5

FB31

5

FB11

5

S405

S401

S401

S410S411S415S414S413S412S409S407

S408

S406S416S402S403S404

JW40

1

JW40

2

JW40

3

JW40

4

JW40

5

R416

R417

R401

R404

R419

R411

R403

R408

R406

R405

R418

R415

R413

F902

F901

T901

C905D901

D903

D904

D902

CN90

3

CN90

2

JW90

2

C901

C903C906

C904

C902

FH902 FH901

FH90

3FH

904

CN701

1

6

S301

-1-2

1 5CN318

J901

• : Uses unleaded solder.• See page 17 for Circuit Boards Location.5-4. PRINTED WIRING BOARDS – KEY, POWER Section –

(Page 18)

(Page 18)

(Page 18)

(Page 18)

(Page 18)

CFD-S07CP

CFD-S07CP

2020

IC B/D

IC B/D

IC B/DIC B/D

TP712TP713TP714TP715

R720(DA11MMVGP)

L2

C16

C8

ANT1

BP1

D2 D3

R1

C2 C1

C4

C3

R21R11

R702

R704

R714

R708R707

C701

BP781

R833

R831

R829R830

R826R827

R823R822R821

R867

R865

R863R862

R864

R861R860R859R858

C866

C856

C859 FB802

R866

BP702

C867

C880

R804R802

C854

C851

L806L807

C877

BP701

C879

C702

R719

C876

TP899

TP805TP895TP894

TP81

1TP

810

TP81

7

C852

TP815TP813 R854

R834

R819

R818

R806

R805 C8

10R8

08

R873

R872R870

R811

C818

C816

R814

R815

C888

R703

CN802

CN1

CN810

CN808CN701

BP782

C817R8

91

JC80

2

TP900R868

C865

C864

C896C895C892

C894C893

D808

R884

L802L803

R875

R874

R880

C885

R857 C890

C891

C822

R813R812

R855

R852

C889

C887

X1

D1

L6

C886 R881R883

R869

R3

TP706TP705

C703

TP704TP703

TP702TP701

TP806

TP807

C7

C18

D806

D807

TP802

TP801

TP818

TP819

C829

TP814

C803

C863

C804

C825C827C828

X801

C823

C884

C883

C835C834

CN801

R902

R901

R900

R899

R898

R897

R986

R895

R894

R973

R974

R975

R976

R977

R978

R979

R980

R892R994R993R988R987R986

R981R982R983R984R985

R893

R971R970R969

R967

L808R992

LCD401

TP81

2

IC801

C812

TP808 R832

FB80

1

JC80

2C8

41C8

45

R713

R715

R890

R10

C15

R8

C13

R7

C11

C17

C22 C21

L5

R6

C9

R4

R836

R809 D8

01

C962

JC803

R816

R825R824

R889

L810FB804

L804

TP80

3

R877 R876

C853

C24

R879

R878

FB803

C824

L809

C862

C830

C832

Q701

R410

R409

D802

R407

C833R402

R412

TP804

X802

IC701

S701

S801

M702

M701

C5R8

20R8

38R8

37

R850

R851

R853

R803R801

C802

C849

TP816

R810

C878

C881

TP897TP898

R706

R705

TP711

C704

L4

L1

C25

IC1

Q805

Q804

TP821

TP820

TP709

TP707

TP710

TP708

C801

C861 C858

R856C855

R844L805

R425

Q803

Q806

R807

C813

C815

C814C821

C819

C820

R828

C961

R972

R989

R885

R886

L801

C897

C898

C403

IC806

C831

C850

IC803

IC805

IC804

IC802

D401

R701

C882

C10

C14

• See page 17 for waveforms. • See page 25, 26 for IC Block Diagrams. • See page 28 for IC Pin Function Description of IC801.5-5. SCHEMATIC DIAGRAM – MAIN Section (1/3) –

(Page 23)(Page 21)

(Page 22)

CFD-S07CP

CFD-S07CP

2121

IC B/D

FB201

FB205

FB204

FB202

FB203

FB206FB207

HE301

R304

C310

C312

C104C101

C103

C309

C205

C203

C201C204

C305C308

C306

C307

C105

T301

HRP301

S301

R311R310

JC301

C301

C302

C304

R104R102 R103

R107

R110

R301

R210

R207

R204

R203R202

R302

R309

R305 R314 R315

R306

R307

R308

C202

TP302

TP303CN316

CN317CN318

Q302 Q303Q301

IC301

C102

C303

R351

C330

• See page 17 for waveforms. • See page 26 for IC Block Diagram.5-6. SCHEMATIC DIAGRAM – MAIN Section (2/3) –

(Page 20) (Page 22)

CFD-S07CP

CFD-S07CP

2222

IC B/D

IC B/D

D952

R350J301Q102

CN901

R142

C132C232C233C133

FB315

FB215

FB115

CN301

TP902

TP102

TP202

TP901TP903

D951

C143C243C142

C245

C242

C327

C328

C954

C958 C956 C955

C951

TP101

TP201

C135

C134

C136

C137

C235

C234

C236

C237

C126

C227

C127

C228

C128

C129C229

C230C130

C131C231

C320

TP30

1

C322

C323

C325

C321

C225

C125

C124

C224

C220C120C221C121

C324

C964

C963L811

JC80

1JC

804

D953

C241

SP101

SP201

CN311CN310

Q808

R242

R959

R960 R955 R954

R964

R957

R956

R950

R951

R952

R953

R241R240

R239

R245R238

R138

R145

R137

R236

R141

R140

R139

R136

R958

D954

R961R962

R129R130

R229R230

R320

R234R134

R325

R326

R321

R324

R232

R132

R228R128

R225R125

R224R124

R226R126

R223R123

C240

C311

C139

C145

C329

C141

C144

C244C326

C950

R237

R888M901

CN312CN313 R426

IC302

Q202

Q952Q954Q955

Q951

Q953

CN807

SW1

J302

C408

R423

C405

R414

C409 R420

C122

C223

R421

C406

C226

C404 R424

C899 R887

R422

C407

IC807

IC303C140

C957R963

C959

IC401

C239C238

C138

C953 C952

B CN902

• See page 27 for IC Block Diagrams.5-7. SCHEMATIC DIAGRAM – MAIN Section (3/3) –

(Page 20)

(Page 21)

(Page 24)

CFD-S07CP

CFD-S07CP

2323

S403

R419R418R417R416R415R413

S404S405S407S408S409

S410S411S412S413S414S415S416

R401R403R404R405R406R408

W401R411

S406 S402

S401

5-8. SCHEMATIC DIAGRAM – KEY Section –

(Page 20)

CFD-S07CP

CFD-S07CP

2424

FH901FH902

F901

CN902

JW902C903

C904 C906C902

C901

F902

J901 FH903FH904

C905

D903

D904D902

D901

T901

CN903

5-9. SCHEMATIC DIAGRAM – POWER Section –

(Page 22)

CFD-S07CP

25

1

2

34

5

6

7

8

9

10

11

1213

14

28

27

26

24

23

22

21

20

19

18

17

16

15

25

LEVELSHIFT

LEVELSHIFT

THERMALSHUT-DOWN

MONITOR

LEVELSHIFT

LEVELSHIFT D.BUFF

D.BUFF

D.BUFFGND

FIN

(FIN)

VREF

VCC

VCC

(TIN)

TIN

T–

T+

F–

F+

NC

OPIN

SP–

REGB

SP+

SPINRST

REGO

MUTE

GND

(SLIN)

SLIN

SL–

SL+GND

OPOUT

D.BUFF

D.BUFF

D.BUFF

D.BUFF

D.BUFF

REGU

LATO

R

DRIVERMUTE

VCC

VCC

12345

67

8

9

1011

12

24

23

22

20

19

18171615

1413

21

LNA

AGC

DAC

DAC

CONTROL /INTERFACE

ADC

DSP

LOW-IF

ADC

LOUT

VDD

VIO

RCLK

SDIOSCLKSENRST

GNDGND

ROUT

GND

DOUT

GPIO1

DFSGPIO2/DCLK

GPIO2/INT

NCNC

FMI

RFGND

NCNC

AMILNA

AGC

AFC

LDOREG

• IC Block Diagrams

IC1 SI4730-C40 (MAIN Board (1/3))

IC701 BA5826HFP-E2 (MAIN Board (1/3))

CFD-S07CP

26

2

3

VSS

NC

1CE

4 VOUT

5 VIN

ON/OFFCONTROL

REFERENCEVOLTAGE CIRCUIT

OVERCURRENTPROTECTOR

12

3

6

9

10

11

12

8

7

4

5

22

TAPE

TAPE

TAPE

BUF AMPA1

BUF AMPA2

NABAMP1

NABAMP2

23

24

15

14

13

21

20

17

16

RADIO

BUF AMPB1

BUF AMPB2

MUTE

MUTE

ON

ON

ON

7dB

26dB

26dB

MONITORAMP

LOGIC

18

19

MUTE

7dB

MONITORAMP

LINE

TAPERADIO

LINE

ALC2

ALC1

DET

RECAMP1

RECAMP2

2.1

REFAMP

MICAMP1

VCC

R.LO

LINE

R.RAD

TAPE

R.LIN

MIC

L.LO

REC

L.RAD

MIC I/EX

L.LINAGC

L.PO

L.NF

L.RO

L.IN

REF

GND

R.IN

R.RO

R.NF

R.PO

MIC.NF

IC803 S-T111B15MC-OGATFG (MAIN Board (1/3))IC804 S-T111B15MC-OGATFG (MAIN Board (1/3))

IC301 TA2068NG (MAIN Board (2/3))

CFD-S07CP

27

REF

IN

30

A GN

D

29

IN R

A

31

IN R

CD

2

IN L

CD

1

IN LC

3

ICOU

T L

12

ICOU

T R

11

IN R

C

4

IN L

AU

5

IN R

AU

6

IN LE

7

IN R

E

8

IN L

TU

9

IN R

TU

10

IN LA

32

CLK

27

VCC

26

DATA

28

SB1

24

SA

23

L OUT

25

R OU

T

21

BASS

R2

20

SB2

22

BASS

R1

19

BASS

L2

17BA

SS L1

18

SURROUND

INPUT GAIN

I2C BUS LOGIC VCCVCC/2

INPUT SELECTOR

TREBLE/BASS

VOLUME VOLUME

TRE

L

15

TRE

R

16

VOLIN

L

13

VOLIN

R

14

IC302 UTC8227S (MAIN Board (3/3))

IC303 BD3491FS-SE2 (MAIN Board (3/3))

6

L-IN

L-NF

PREG

ND

L-BS

L-OU

T

STBY

R-IN

R-NF

RIPP

LE

R-BS

R-OU

T

VCC

5 4 3 2 1

7 8 9 10 11 12

CFD-S07CP

28

• IC Pin Function Description

MAIN BOARD (1/3) IC801 TC94A77FG-717(CD-RF AMP/SERVO CONTROL, AUDIO DAC, DSP, LCD DRIVER, SYSTEM CONTROL)

Pin No. Pin Name I/O Description1 FMO O Feed (Sled) servo equalizer signal output2 DMO O Disc (spindle) servo equalizer signal output3 KEY1-I I Key signal input4 KEY2-I I Key signal input5 CD_LIMIT/LID IN I CD Door open/close and CD Limit switch signal input6 BATT-CHK-H I Battery voltage power check input7 6V CHK I 6.2V power check input8 SIMUKE I Model destination input9 VREG — 1.5V reference voltage terminal

10 MXO O Sub system oscillation output (4.19MHz)11 MXI I Sub system oscillation input (4.19MHz)12 VDD3 — Power supply (VDD+3.3V (I/O))13 VSS — Ground 14 VSSP3 — Ground (VCO)15 VCOI I VCO input16 VDDP3 — Power supply (VDD+3.3V (VCO)) 17 FUNC_TC O Tape function select signal output18 RESET I Initial reset signal input19 VDD1 — Power supply (VDD+1.5V)20 VSS — Ground 21 DVSS3 — Ground (DAC)22 LO O CD audio L-CH signal output23 DVR I DAC reference voltage terminal24 RO O CD audio R-CH signal output25 DVDD3 — Power supply (VDD+3.3V (DAC))26 XVSS1 — Ground (OSC) 27 XI I Main system oscillation input (16.93MHz)28 XO O Main system oscillation output (16.93MHz)29 XVDD1 — Power supply (VDD+1.5V (OSC))30 RMC I Sircs signal input31 TU-DAT I/O Tuner serial I2C data input/output32 TU-CLK O Tuner serial I2C clock output33 EEP-CLK O EEPROM/EVR control serial I2C clock output34 EEP-DAT I/O EEPROM/EVR control serial I2C data input/output35 TU RESET O Tuner reset signal output36 VSS — Ground 37 VDD1 — Power supply (VDD+1.5V)38 P-CONT O Power control signal output39 A-MUTE O Audio mute signal output40 MOTOR-MUTE O Motor drive mute signal output41 ISS1 O Tuner beat change signal output42 ISS2 O Tuner beat change signal output43 POWER KEY I Power key signal input44 AUDIO IN CHECK I Audio signal in check signal input45 TC-OPERATION I Tape play detect signal input (L: Play)46 TAPE REC I Tape REC signal input (H: REC)

47 to 49 NC — Not used (Open)50 VDD3 — Power supply (+3.3V)

51 to 54 NC — Not used (Open)55 D-SHIFT2 O Clock shift signal output56 D-SHIFT1 O Clock shift signal output57 ACDC CHK I AC power check signal input58 NC — Not used (Open)59 WR O LCD driver data write signal output60 CS O LCD driver chip select signal output61 DATA O LCD driver data output

CFD-S07CP

29

Pin No. Pin Name I/O Description62 NC — Not used (Open)63 VDDM1 — Power supply (Memory VDD+1.5V)64 HOLD I Hold input65 VSS — Ground66 VDD1 — Power supply (VDD+1.5V)67 PDO O EFM and PLCK phase deference signal output68 TMAX O TMAX detection result output69 LPFN I PLL circuit LPF amplifi er inversion input70 LPFO O PLL circuit LPF amplifi er output71 PVREF — PLL circuit 1.65V reference voltage terminal72 VCOF — VCO fi lter terminal73 RVDD3 — Power supply (CD+3.3V)74 SLCO O EFM slice level output terminal75 RFI I RF signal input76 RFRPI I RF ripple signal input77 RFGO O RF equalizer amplifi er output78 AGCI I RF signal AGC amplifi er input79 RFO O RF signal generation amplifi er output80 EQSET O Test monitor output81 RVSS3 — Power supply (+3.3V (RF/VCO/PLL))82 FNI2 (C) I CD pick-up main beam C signal input83 FNI1 (A) I CD pick-up main beam A signal input84 FPI2 (D) I CD pick-up main beam D signal input85 FPI1 (B) I CD pick-up main beam B signal input86 TPI (F) I CD pick-up main beam F signal input87 TNI (E) I CD pick-up main beam E signal input88 VRO — Reference voltage (1.65V) terminal89 MDI I Monitor photo diode amplifi er input90 LDO O Laser diode drive control signal output91 AVSS3 — Ground92 RFZI I RF ripple zero-cross signal input93 RFRP O RF ripple signal output94 SBAD O RFDC output95 FEI O Focus error signal output96 TEI O Tracking error signal output97 TEZI I Tracking error zero -cross signal input98 AVDD3 — Power supply (+3.3V) 99 FOO O Focus servo equalizer signal output

100 TRO O Tracking servo equalizer signal output

30

CFD-S07CPSECTION 6

EXPLODED VIEWS

1 4-167-386-11 LID, BATTERY CASE 2 3-252-827-01 SCREW (B2.6), (+) BV TAPPING

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

Note:• -XX and -X mean standardized parts, so

they may have some difference from the original one.

• Items marked “*” are not stocked since they are seldom required for routine ser-vice. Some delay should be anticipated when ordering these items.

• The mechanical parts with no reference number in the exploded views are not sup-plied.

• Color Indication of Appearance Parts Ex-ample:

KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet’s Color

6-1. OVERALL SECTION

The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety.Replace only with part number specifi ed.

Les composants identifi és par une marque 0 sont critiques pour la sécurité.Ne les remplacer que par une pièce por-tant le numéro spécifi é.

1

2

2

2

2

22

cabinet (front) section


cabinet (upper) section 1

• Accessories are given in the last of the electrical parts list.


31

CFD-S07CP

6-2. CABINET (FRONT) SECTION

51 X-2547-266-1 CABINET (FRONT) ASSY 52 1-831-985-32 CABLE, FLEXIBLE FLAT (5 CORE) 53 3-831-441-11 CUSHION (B) 54 3-252-827-01 SCREW (B2.6), (+) BV TAPPING 55 A-1765-444-A JACK BOARD, COMPLETE

56 4-167-385-21 BUTTON (EXCEPT CET,IT)

56 4-167-385-31 BUTTON (CET,IT) 57 A-1765-443-A KEY BOARD, COMPLETE 58 3-254-070-01 SCREW SP101 1-826-280-61 SPEAKER (7.7cm) (L-CH) SP201 1-826-280-61 SPEAKER (7.7cm) (R-CH)


51

52

53

54

54

54

54

54

54

55

56

5758

5853

53

53

SP101

SP201

Note: If the wire (fl at type) was replaced, fold it some as the wire (fl at type) before replacement.

32

CFD-S07CP

6-3. CABINET (UPPER) SECTION (1)

101 3-047-468-21 DAMPER 102 3-252-827-01 SCREW (B2.6), (+) BV TAPPING 103 A-1760-733-A MD BLOCK ASSY (EXCEPT CET,IT) 103 A-1761-365-A MD BLOCK ASSY (CET,IT) 104 4-167-410-01 LEVER (REC)

105 3-254-022-01 SCREW 106 A-1765-456-A SWITCH BOARD, COMPLETE 107 3-254-070-01 SCREW 108 3-831-441-11 CUSHION (B) 109 4-167-394-11 BUTTON (REC)

110 4-167-393-11 BUTTON (PLAY)

111 4-167-396-11 BUTTON (REW) 112 4-167-395-11 BUTTON (FF) 113 4-167-397-11 BUTTON (STOP) 114 4-167-398-11 BUTTON (PAUSE) 115 4-183-213-01 CUSHION (CASSETTE BUTTON)

116 4-167-392-11 LID, CASSETTE 117 4-167-415-01 SPRING, CASSETTE 118 4-167-389-11 HANDLE HE301 1-500-813-11 HEAD, ERASE (ERASE) HRP301 3-266-053-01 HEAD, RP (REC/PB)


101

102

102

103

106

107

108

109110

111112

113

115

116

117

118

114

104105

105

102

not supplied

not supplied

not supplied

cabinet (upper) section 2

HE301HRP301

not supplied

not supplied

33

CFD-S07CP

6-4. CABINET (UPPER) SECTION (2)

151 4-167-399-01 COVER, CD 152 3-931-379-21 RUBBER, VIBRATION PROOF (RED) 153 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING 154 1-838-039-31 CABLE, FLEXIBLE FLAT (16 CORE) 155 4-175-101-01 CUSHION (FFC)

156 1-831-758-32 CABLE, FLEXIBLE FLAT (6 CORE) 157 3-931-379-31 RUBBER, VIBRATION PROOF (GREEN)0 158 A-1780-028-A OPTICAL PICK-UP (DA11MMVGP) 159 3-252-827-01 SCREW (B2.6), (+) BV TAPPING

160 3-047-468-11 DAMPER 161 4-167-382-11 CABINET (UPPER) 162 4-167-416-01 SPRING, CD 163 4-167-390-11 LID, CD 164 1-452-899-11 MAGNET

165 4-167-391-01 PLATE, CHUCKING 166 3-258-284-01 SHEET (CHUCK) 167 3-253-143-01 SCREW (B2.6), (+) P TAPPING S801 1-692-960-11 SWITCH, PUSH (1 KEY) (PUSH OPEN/CLOSE Z)


151

152

153

154155

156

157

157

158

159

160

161162 163

164

165

166

167

153

153152

not supplied

not supplied

not suppliednot supplied

S801

not supplied

not supplied(MOTOR board)

Note: If the wire (fl at type) was replaced, fold it some as the wire (fl at type) before replacement.

34

CFD-S07CP

6-5. CABINET (REAR) SECTION

201 4-167-383-21 CABINET (REAR) 202 4-167-417-01 FOOT (FRONT), RUBBER 203 3-252-540-01 SPRING (+. –), BATTERY 204 4-173-526-01 TERMINAL (A (+, –)), BATTERY 205 4-167-412-01 TERMINAL (–), BATTERY

206 4-173-527-01 TERMINAL (B (+, –)), BATTERY 207 3-252-827-01 SCREW (B2.6), (+) BV TAPPING 208 A-1765-450-A POWER BOARD, COMPLETE (EXCEPT CND,E92,MX) 208 A-1770-258-A POWER BOARD, COMPLETE (CND,E92,MX) 209 3-831-441-11 CUSHION (B)

210 A-1765-446-A MAIN BOARD, COMPLETE (CET,IT) 210 A-1770-222-A MAIN BOARD, COMPLETE (SP) 210 A-1770-234-A MAIN BOARD, COMPLETE (AUS,EA,TH,TW) 210 A-1770-246-A MAIN BOARD, COMPLETE (E41,AR)

210 A-1770-253-A MAIN BOARD, COMPLETE (CND,E92,MX) 211 4-167-388-01 HOLDER (LCD1027) 212 3-254-070-01 SCREW 213 3-254-151-01 SCREW (B2.6), (+) P TAPPING 214 4-167-413-01 TERMINAL, ANTENNA

215 3-252-833-01 SCREW (M3), (+) P 216 4-167-411-01 TERMINAL (+), BATTERY ANT1 1-754-711-11 ANTENNA, TELESCOPIC (FM) D401 6-503-151-01 LED L-3A7HD-16LSF42.5-01 (OPR/BATT)0 F901 1-533-468-12 FUSE, GLASS (DIA. 5) (T2AL/250V)

0 F902 1-533-468-12 FUSE, GLASS (DIA. 5) (T2AL/250V) LCD401 1-811-084-11 DISPLAY PANEL, LIQUID CRYSTAL0 T901 1-445-818-11 TRANSFORMER, POWER (CND,E92,MX,TW)0 T901 1-445-820-11 TRANSFORMER, POWER (E41,AUS,AR,CET,EA,IT,SP,TH)


201

202

203203

205206

207

207

208

207

207

209209

210 211

212

213213

214 215

216

204

207

ANT1

D401not supplied(RMC board)

LCD401

not supplied

not supplied

not supplied

not supplied

not supplied

F902

F901T901

35

CFD-S07CPSECTION 7

ELECTRICAL PARTS LIST

A-1765-444-A JACK BOARD, COMPLETE *********************

< CAPACITOR >

C132 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C133 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C232 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C233 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

< FERRITE BEAD >

FB115 1-400-981-21 INDUCTOR (EMI FERRITE) FB215 1-400-981-21 INDUCTOR (EMI FERRITE) FB315 1-400-981-21 INDUCTOR (EMI FERRITE)

< JACK >

J302 1-566-822-51 JACK (AUDIO IN)*************************************************************

A-1765-443-A KEY BOARD, COMPLETE ********************

< RESISTOR >

R401 1-216-819-11 METAL CHIP 680 5% 1/10W R403 1-216-821-11 METAL CHIP 1K 5% 1/10W R404 1-216-821-11 METAL CHIP 1K 5% 1/10W R405 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R406 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R408 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R411 1-216-835-11 METAL CHIP 15K 5% 1/10W R413 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R415 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R416 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R417 1-216-821-11 METAL CHIP 1K 5% 1/10W R418 1-216-821-11 METAL CHIP 1K 5% 1/10W R419 1-216-819-11 METAL CHIP 680 5% 1/10W

< SWITCH >

S401 1-786-050-21 SWITCH, KEYBOARD (POWER) (EXCEPT CET,IT) S401 1-786-050-21 SWITCH, KEYBOARD (OPERATE) (CET,IT) S402 1-786-050-21 SWITCH, KEYBOARD (x) S403 1-786-050-21 SWITCH, KEYBOARD (./PRESET –) S404 1-786-050-21 SWITCH, KEYBOARD (>/PRESET +)

S405 1-786-050-21 SWITCH, KEYBOARD ( /TUNE –) S406 1-786-050-21 SWITCH, KEYBOARD ( /TUNE +) S407 1-786-050-21 SWITCH, KEYBOARD (VOLUME –) S408 1-786-050-21 SWITCH, KEYBOARD (VOLUME +)

S409 1-786-050-21 SWITCH, KEYBOARD (MEGA BASS) S410 1-786-050-21 SWITCH, KEYBOARD (MODE) S411 1-786-050-21 SWITCH, KEYBOARD (zDISPLAY/ENTER, MEMORY) S412 1-786-050-21 SWITCH, KEYBOARD (AUDIO IN) S413 1-786-050-21 SWITCH, KEYBOARD (RADIO BAND/AUTO PRESET)

S414 1-786-050-21 SWITCH, KEYBOARD (CD) S415 1-786-050-21 SWITCH, KEYBOARD (TAPE) S416 1-786-050-21 SWITCH, KEYBOARD (u)*************************************************************

A-1765-446-A MAIN BOARD, COMPLETE (CET,IT) A-1770-222-A MAIN BOARD, COMPLETE (SP) A-1770-234-A MAIN BOARD, COMPLETE (AUS,EA,TH,TW) A-1770-246-A MAIN BOARD, COMPLETE (E41,AR) A-1770-253-A MAIN BOARD, COMPLETE (CND,E92,MX) (including RMC BOARD, COMPLETE) *********************

3-254-070-01 SCREW 4-167-388-01 HOLDER (LCD1027)

< CAPACITOR >

C1 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C2 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C3 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C4 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C5 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C7 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C8 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C9 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C10 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C11 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C13 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C14 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C15 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C16 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C17 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V

C18 1-126-947-11 ELECT 47uF 20% 35V C21 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C22 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C24 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C25 1-162-919-11 CERAMIC CHIP 22PF 5% 50V

C101 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C102 1-104-658-91 ELECT 100uF 20% 10V C103 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C104 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V


Note:• Due to standardization, replacements in

the parts list may be different from the parts specifi ed in the diagrams or the com-ponents used on the set.

• RESISTORS All resistors are in ohms. METAL: Metal-fi lm resistor. METAL OXIDE: Metal oxide-fi lm resistor. F: nonfl ammable• CAPACITORS uF: μF• COILS uH: μH• SEMICONDUCTORS In each case, u: μ, for example: uA. . : μA. . , uPA. . , μPA. . , uPB. . : μPB. . , uPC. . , μPC. . , uPD. . : μPD. .


SECTION 7ELECTRICAL PARTS LIST JACK KEY MAIN

When indicating parts by reference num-ber, please include the board name.

The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety.Replace only with part number specifi ed.

Les composants identifi és par une marque 0 sont critiques pour la sécurité.Ne les remplacer que par une pièce por-tant le numéro spécifi é.


CFD-S07CP

36

C105 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C120 1-126-960-11 ELECT 1uF 20% 50V C121 1-126-960-11 ELECT 1uF 20% 50V C122 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C124 1-126-960-11 ELECT 1uF 20% 50V

C125 1-126-960-11 ELECT 1uF 20% 50V C126 1-126-960-11 ELECT 1uF 20% 50V C127 1-126-960-11 ELECT 1uF 20% 50V C128 1-126-960-11 ELECT 1uF 20% 50V C129 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C130 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C131 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C134 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C135 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C136 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C137 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C138 1-126-960-11 ELECT 1uF 20% 50V C139 1-126-957-11 ELECT 0.22uF 20% 50V C140 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C141 1-126-947-11 ELECT 47uF 20% 35V

C142 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C143 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C144 1-126-925-91 ELECT 470uF 20% 10V C145 1-104-658-91 ELECT 100uF 20% 10V C201 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V

C202 1-104-658-91 ELECT 100uF 20% 10V C203 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C204 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C205 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C220 1-126-960-11 ELECT 1uF 20% 50V

C221 1-126-960-11 ELECT 1uF 20% 50V C223 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C224 1-126-960-11 ELECT 1uF 20% 50V C225 1-126-960-11 ELECT 1uF 20% 50V C226 1-126-960-11 ELECT 1uF 20% 50V

C227 1-126-960-11 ELECT 1uF 20% 50V C228 1-126-960-11 ELECT 1uF 20% 50V C229 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C230 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C231 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C234 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C235 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C236 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C237 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C238 1-126-960-11 ELECT 1uF 20% 50V

C239 1-126-957-11 ELECT 0.22uF 20% 50V C240 1-126-947-11 ELECT 47uF 20% 35V C241 1-104-658-91 ELECT 100uF 20% 10V C242 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C243 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C244 1-126-925-91 ELECT 470uF 20% 10V C245 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C301 1-104-658-91 ELECT 100uF 20% 10V C302 1-104-658-91 ELECT 100uF 20% 10V C303 1-104-658-91 ELECT 100uF 20% 10V

C304 1-126-947-11 ELECT 47uF 20% 35V C305 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C306 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C307 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C308 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C309 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C310 1-162-960-11 CERAMIC CHIP 220PF 10% 50V C311 1-126-947-11 ELECT 47uF 20% 35V C312 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C320 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

C321 1-104-658-91 ELECT 100uF 20% 10V C322 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C323 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C324 1-126-947-11 ELECT 47uF 20% 35V C325 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C326 1-126-934-11 ELECT 220uF 20% 16V C327 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C328 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C329 1-126-935-11 ELECT 470uF 20% 16V C330 1-104-662-91 ELECT 22uF 20% 25V

C403 1-126-964-11 ELECT 10uF 20% 50V (CET,IT) C404 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V (CET,IT) C405 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V (CET,IT) C406 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V (CET,IT) C407 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V (CET,IT)

C408 1-126-964-11 ELECT 10uF 20% 50V (CET,IT) C409 1-162-927-11 CERAMIC CHIP 100PF 5% 50V (CET,IT) C701 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C702 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C703 1-126-923-91 ELECT 220uF 20% 10V

C704 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C801 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C802 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C803 1-126-947-11 ELECT 47uF 20% 35V C804 1-126-947-11 ELECT 47uF 20% 35V

C810 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C812 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C813 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C814 1-104-658-91 ELECT 100uF 20% 10V C815 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C816 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C817 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C818 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C819 1-126-947-11 ELECT 47uF 20% 35V C820 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C821 1-126-963-11 ELECT 4.7uF 20% 50V C822 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C823 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C824 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C825 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C827 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C828 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C829 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C830 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C831 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C832 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C833 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (CET,IT) C834 1-104-658-91 ELECT 100uF 20% 10V C835 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

MAIN


CFD-S07CP

3737

C841 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C845 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C849 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C850 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C851 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C852 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C853 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C854 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C855 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C856 1-164-245-11 CERAMIC CHIP 0.015uF 10% 25V


C864 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V C865 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C866 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C867 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C876 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C877 1-104-658-91 ELECT 100uF 20% 10V C878 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C879 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C880 1-104-658-91 ELECT 100uF 20% 10V C881 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V

C882 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C883 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C884 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C885 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C886 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C887 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C888 1-104-658-91 ELECT 100uF 20% 10V C889 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C890 1-104-662-91 ELECT 22uF 20% 25V C891 1-126-947-11 ELECT 47uF 20% 35V

C892 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C893 1-104-658-91 ELECT 100uF 20% 10V C894 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C895 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C896 1-126-933-11 ELECT 100uF 20% 16V

C897 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C898 1-126-933-11 ELECT 100uF 20% 16V C899 1-164-156-11 CERAMIC CHIP 0.1uF 25V C950 1-126-937-11 ELECT 4700uF 20% 16V C951 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

C952 1-104-662-91 ELECT 22uF 20% 25V C953 1-126-925-91 ELECT 470uF 20% 10V C954 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C955 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C956 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C957 1-126-923-91 ELECT 220uF 20% 10V C958 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C959 1-104-658-91 ELECT 100uF 20% 10V C961 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C962 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V

< CONNECTOR >

CN1 1-815-443-11 PIN, CONNECTOR (PWB) 2P CN301 1-815-445-11 PIN, CONNECTOR (PWB) 4P CN310 1-815-551-11 PIN, CONNECTOR (PWB) 3P CN316 1-815-445-11 PIN, CONNECTOR (PWB) 4P

CN801 1-784-766-11 CONNECTOR, FFC 5P CN807 1-815-445-11 PIN, CONNECTOR (PWB) 4P CN808 1-784-767-11 CONNECTOR, FFC 6P CN810 1-770-646-11 CONNECTOR, FFC/FPC 16P CN901 1-815-444-11 PIN, CONNECTOR (PWB) 3P

< DIODE >

D1 8-719-062-51 DIODE 1PS226-115 D2 8-719-991-33 DIODE 1SS133T-77 D3 8-719-991-33 DIODE 1SS133T-77 D401 6-503-151-01 LED L-3A7HD-16LSF42.5-01 (OPR/BATT) D801 6-501-817-01 DIODE MA2J1110GLS0

D802 6-501-817-01 DIODE MA2J1110GLS0 (CET,IT) D806 6-501-817-01 DIODE MA2J1110GLS0 D807 6-501-817-01 DIODE MA2J1110GLS0 D808 6-500-335-01 DIODE MC2838-T112-1 D951 6-501-817-01 DIODE MA2J1110GLS0

D952 6-500-334-01 DIODE MC2836-T112-1 D953 8-719-978-33 DIODE DTZ-TT11-6.8B D954 6-501-719-01 DIODE MAZ8039GHLS0

< FERRITE BEAD >

FB201 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT) FB201 1-400-979-21 INDUCTOR (EMI FERRITE) (CET,IT) FB202 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT) FB202 1-400-979-21 INDUCTOR (EMI FERRITE) (CET,IT) FB203 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT)

FB203 1-400-979-21 INDUCTOR (EMI FERRITE) (CET,IT) FB204 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT) FB204 1-400-979-21 INDUCTOR (EMI FERRITE) (CET,IT) FB205 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT) FB205 1-400-979-21 INDUCTOR (EMI FERRITE) (CET,IT)

FB206 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT) FB206 1-400-979-21 INDUCTOR (EMI FERRITE) (CET,IT) FB207 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT) FB207 1-400-979-21 INDUCTOR (EMI FERRITE) (CET,IT) FB801 1-400-979-21 INDUCTOR (EMI FERRITE)

FB802 1-400-981-21 INDUCTOR (EMI FERRITE) FB803 1-400-979-21 INDUCTOR (EMI FERRITE) FB804 1-400-981-21 INDUCTOR (EMI FERRITE)

< IC >

IC1 6-715-094-01 IC SI4730-C40 IC301 6-710-092-01 IC TA2068NG(5,HZ) IC302 6-710-261-01 IC UTC8227 S IC303 6-713-384-01 IC BD3491FS-SE2 IC701 6-710-637-01 IC BA5826HFP-E2

IC801 6-715-263-01 IC TC94A77FG-717 IC802 6-715-093-01 IC XC6216D332JR IC803 6-705-310-01 IC S-T111B15MC-OGATFG IC804 6-705-310-01 IC S-T111B15MC-OGATFG IC805 6-703-740-01 IC S-24CS02AFT-TB-G

IC806 6-715-273-01 IC HT1621 IC807 8-759-581-11 IC NJM2125F(TE2) (CET,IT)

< JACK >

J301 1-815-325-11 JACK (i)

< JUMPER RESISTOR >

JC301 1-216-864-11 SHORT CHIP 0

MAIN


CFD-S07CP

38

JC801 1-216-864-11 SHORT CHIP 0 (CET,IT) JC802 1-216-864-11 SHORT CHIP 0 JC803 1-216-864-11 SHORT CHIP 0 (EXCEPT CET,IT) JC804 1-216-864-11 SHORT CHIP 0 (CET,IT)

< COIL >

L1 1-457-904-11 COIL, BAR ANTENNA (AM) L2 1-410-517-11 INDUCTOR 47uH L4 1-412-006-31 INDUCTOR 10uH L5 1-410-750-41 INDUCTOR 0.47uH L6 1-412-975-31 INDUCTOR 0.47uH

L802 1-410-509-11 INDUCTOR 10uH L803 1-410-513-11 INDUCTOR 22uH L804 1-410-750-41 INDUCTOR 0.47uH L805 1-410-517-11 INDUCTOR 47uH L811 1-410-509-11 INDUCTOR 10uH

< LIQUID CRYSTAL DISPLAY >

LCD401 1-811-084-11 DISPLAY PANEL, LIQUID CRYSTAL

< TRANSISTOR >

Q102 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q202 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q301 8-729-901-81 TRANSISTOR 2SC2412K-T-146-R Q302 8-729-027-46 TRANSISTOR DTC114YKA-T146 Q303 8-729-027-46 TRANSISTOR DTC114YKA-T146

Q701 6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF Q803 6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF (CET,IT) Q804 6-552-482-01 FET INJ0203AC1-T112-1 Q805 8-729-027-46 TRANSISTOR DTC114YKA-T146 Q806 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF (CET,IT)

Q808 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q951 6-551-444-01 TRANSISTOR RT1N436C-TP-1 Q952 8-729-040-76 TRANSISTOR KTA1273-Y-AT Q953 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q954 8-729-018-99 TRANSISTOR 2SD2394-F

Q955 8-729-036-86 TRANSISTOR KTC3203Y-AT

< RESISTOR >

R1 1-216-797-11 METAL CHIP 10 5% 1/10W R3 1-216-821-11 METAL CHIP 1K 5% 1/10W R4 1-216-821-11 METAL CHIP 1K 5% 1/10W R6 1-216-821-11 METAL CHIP 1K 5% 1/10W R7 1-216-821-11 METAL CHIP 1K 5% 1/10W

R8 1-216-821-11 METAL CHIP 1K 5% 1/10W R10 1-216-821-11 METAL CHIP 1K 5% 1/10W R11 1-216-864-11 SHORT CHIP 0 R21 1-216-864-11 SHORT CHIP 0 R102 1-216-807-11 METAL CHIP 68 5% 1/10W

R103 1-216-843-11 METAL CHIP 68K 5% 1/10W R104 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R107 1-216-835-11 METAL CHIP 15K 5% 1/10W R110 1-216-809-11 METAL CHIP 100 5% 1/10W R123 1-216-837-11 METAL CHIP 22K 5% 1/10W

R124 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R125 1-216-833-11 METAL CHIP 10K 5% 1/10W R126 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R128 1-216-833-11 METAL CHIP 10K 5% 1/10W R129 1-216-839-11 METAL CHIP 33K 5% 1/10W

R130 1-216-828-11 METAL CHIP 3.9K 5% 1/10W

R132 1-216-836-11 METAL CHIP 18K 5% 1/10W R134 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R136 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R137 1-216-821-11 METAL CHIP 1K 5% 1/10W R138 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R139 1-216-821-11 METAL CHIP 1K 5% 1/10W R140 1-216-811-11 METAL CHIP 150 5% 1/10W R141 1-216-789-11 METAL CHIP 2.2 5% 1/10W R142 1-216-811-11 METAL CHIP 150 5% 1/10W R145 1-216-833-11 METAL CHIP 10K 5% 1/10W

R202 1-216-807-11 METAL CHIP 68 5% 1/10W R203 1-216-843-11 METAL CHIP 68K 5% 1/10W R204 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R207 1-216-835-11 METAL CHIP 15K 5% 1/10W R210 1-216-809-11 METAL CHIP 100 5% 1/10W

R223 1-216-837-11 METAL CHIP 22K 5% 1/10W R224 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R225 1-216-833-11 METAL CHIP 10K 5% 1/10W R226 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R228 1-216-833-11 METAL CHIP 10K 5% 1/10W

R229 1-216-839-11 METAL CHIP 33K 5% 1/10W R230 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R232 1-216-836-11 METAL CHIP 18K 5% 1/10W R234 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R236 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R237 1-216-821-11 METAL CHIP 1K 5% 1/10W R238 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R239 1-216-821-11 METAL CHIP 1K 5% 1/10W R240 1-216-811-11 METAL CHIP 150 5% 1/10W R241 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R242 1-216-811-11 METAL CHIP 150 5% 1/10W R245 1-216-833-11 METAL CHIP 10K 5% 1/10W R301 1-216-857-11 METAL CHIP 1M 5% 1/10W R302 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R304 1-216-821-11 METAL CHIP 1K 5% 1/10W

R305 1-216-817-11 METAL CHIP 470 5% 1/10W R306 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R307 1-216-797-11 METAL CHIP 10 5% 1/10W R308 1-216-837-11 METAL CHIP 22K 5% 1/10W R309 1-216-805-11 METAL CHIP 47 5% 1/10W

R310 1-216-857-11 METAL CHIP 1M 5% 1/10W R311 1-216-857-11 METAL CHIP 1M 5% 1/10W R314 1-216-817-11 METAL CHIP 470 5% 1/10W R315 1-216-817-11 METAL CHIP 470 5% 1/10W R320 1-216-837-11 METAL CHIP 22K 5% 1/10W

R321 1-216-809-11 METAL CHIP 100 5% 1/10W R324 1-216-809-11 METAL CHIP 100 5% 1/10W R325 1-216-817-11 METAL CHIP 470 5% 1/10W R326 1-216-817-11 METAL CHIP 470 5% 1/10W R350 1-216-821-11 METAL CHIP 1K 5% 1/10W

R351 1-216-864-11 SHORT CHIP 0 R402 1-216-845-11 METAL CHIP 100K 5% 1/10W (CET,IT) R407 1-216-833-11 METAL CHIP 10K 5% 1/10W (CET,IT) R409 1-216-841-11 METAL CHIP 47K 5% 1/10W (CET,IT) R410 1-216-833-11 METAL CHIP 10K 5% 1/10W (CET,IT)

R412 1-216-833-11 METAL CHIP 10K 5% 1/10W (EXCEPT CET,IT)

MAIN


CFD-S07CP

3939

R414 1-216-821-11 METAL CHIP 1K 5% 1/10W (CET,IT) R420 1-216-859-11 METAL CHIP 1.5M 5% 1/10W (CET,IT) R421 1-216-825-11 METAL CHIP 2.2K 5% 1/10W (CET,IT) R422 1-216-825-11 METAL CHIP 2.2K 5% 1/10W (CET,IT) R423 1-216-837-11 METAL CHIP 22K 5% 1/10W (CET,IT)

R424 1-216-837-11 METAL CHIP 22K 5% 1/10W (CET,IT) R425 1-216-837-11 METAL CHIP 22K 5% 1/10W (CET,IT) R701 1-216-837-11 METAL CHIP 22K 5% 1/10W R702 1-216-837-11 METAL CHIP 22K 5% 1/10W R703 1-216-845-11 METAL CHIP 100K 5% 1/10W

R704 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R705 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R706 1-216-864-11 SHORT CHIP 0 R707 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R708 1-216-864-11 SHORT CHIP 0

R713 1-216-837-11 METAL CHIP 22K 5% 1/10W R714 1-216-864-11 SHORT CHIP 0 R715 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R719 1-216-864-11 SHORT CHIP 0 R720 1-216-864-11 SHORT CHIP 0

R801 1-216-864-11 SHORT CHIP 0 R802 1-216-864-11 SHORT CHIP 0 R803 1-216-864-11 SHORT CHIP 0 R804 1-216-864-11 SHORT CHIP 0 R805 1-216-821-11 METAL CHIP 1K 5% 1/10W

R806 1-216-821-11 METAL CHIP 1K 5% 1/10W R807 1-216-821-11 METAL CHIP 1K 5% 1/10W R808 1-216-821-11 METAL CHIP 1K 5% 1/10W R809 1-216-813-11 METAL CHIP 220 5% 1/10W R810 1-216-821-11 METAL CHIP 1K 5% 1/10W

R811 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R812 1-216-864-11 SHORT CHIP 0 R813 1-216-864-11 SHORT CHIP 0 R814 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R815 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R816 1-216-853-11 METAL CHIP 470K 5% 1/10W R818 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R819 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R820 1-216-864-11 SHORT CHIP 0 R821 1-216-817-11 METAL CHIP 470 5% 1/10W

R822 1-216-817-11 METAL CHIP 470 5% 1/10W R823 1-216-817-11 METAL CHIP 470 5% 1/10W R824 1-216-817-11 METAL CHIP 470 5% 1/10W R825 1-216-821-11 METAL CHIP 1K 5% 1/10W R826 1-216-817-11 METAL CHIP 470 5% 1/10W

R827 1-216-821-11 METAL CHIP 1K 5% 1/10W R828 1-216-817-11 METAL CHIP 470 5% 1/10W R829 1-216-821-11 METAL CHIP 1K 5% 1/10W R830 1-216-821-11 METAL CHIP 1K 5% 1/10W R831 1-216-817-11 METAL CHIP 470 5% 1/10W

R832 1-216-833-11 METAL CHIP 10K 5% 1/10W (CET,IT) R833 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R834 1-216-833-11 METAL CHIP 10K 5% 1/10W R836 1-216-821-11 METAL CHIP 1K 5% 1/10W

R837 1-216-864-11 SHORT CHIP 0 R838 1-216-864-11 SHORT CHIP 0 R844 1-216-821-11 METAL CHIP 1K 5% 1/10W R850 1-216-821-11 METAL CHIP 1K 5% 1/10W R851 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R852 1-216-821-11 METAL CHIP 1K 5% 1/10W R853 1-216-851-11 METAL CHIP 330K 5% 1/10W R854 1-216-833-11 METAL CHIP 10K 5% 1/10W R855 1-216-841-11 METAL CHIP 47K 5% 1/10W R856 1-216-835-11 METAL CHIP 15K 5% 1/10W

R857 1-216-839-11 METAL CHIP 33K 5% 1/10W R858 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R859 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R860 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R861 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R862 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R863 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R864 1-216-864-11 SHORT CHIP 0 R865 1-216-864-11 SHORT CHIP 0 R866 1-216-797-11 METAL CHIP 10 5% 1/10W

R867 1-216-864-11 SHORT CHIP 0 R868 1-216-864-11 SHORT CHIP 0 R869 1-216-817-11 METAL CHIP 470 5% 1/10W R870 1-216-818-11 METAL CHIP 560 5% 1/10W R872 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R873 1-216-813-11 METAL CHIP 220 5% 1/10W R874 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R875 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R876 1-216-841-11 METAL CHIP 47K 5% 1/10W R877 1-216-825-11 METAL CHIP 2.2K 5% 1/10W


R884 1-216-857-11 METAL CHIP 1M 5% 1/10W R885 1-216-845-11 METAL CHIP 100K 5% 1/10W R886 1-216-841-11 METAL CHIP 47K 5% 1/10W R887 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R888 1-216-833-11 METAL CHIP 10K 5% 1/10W

R889 1-216-841-11 METAL CHIP 47K 5% 1/10W R890 1-216-837-11 METAL CHIP 22K 5% 1/10W (CND,E92,MX) R890 1-216-838-11 METAL CHIP 27K 5% 1/10W (E41,AR) R890 1-216-839-11 METAL CHIP 33K 5% 1/10W (SP) R890 1-216-864-11 SHORT CHIP 0 (CET,IT)

R891 1-216-835-11 METAL CHIP 15K 5% 1/10W (SP) R891 1-216-837-11 METAL CHIP 22K 5% 1/10W (E41,AR) R891 1-216-841-11 METAL CHIP 47K 5% 1/10W (CND,E92,MX) R891 1-216-864-11 SHORT CHIP 0 (AUS,EA,TH,TW) R892 1-216-833-11 METAL CHIP 10K 5% 1/10W


MAIN


CFD-S07CP

40


R950 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R951 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R952 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R953 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R954 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R955 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R956 1-216-833-11 METAL CHIP 10K 5% 1/10W R957 1-216-833-11 METAL CHIP 10K 5% 1/10W R958 1-216-821-11 METAL CHIP 1K 5% 1/10W R959 1-216-821-11 METAL CHIP 1K 5% 1/10W

R960 1-216-821-11 METAL CHIP 1K 5% 1/10W R961 1-216-821-11 METAL CHIP 1K 5% 1/10W R962 1-216-817-11 METAL CHIP 470 5% 1/10W R963 1-216-833-11 METAL CHIP 10K 5% 1/10W R964 1-216-841-11 METAL CHIP 47K 5% 1/10W





R988 1-216-833-11 METAL CHIP 10K 5% 1/10W R989 1-216-864-11 SHORT CHIP 0 R992 1-216-864-11 SHORT CHIP 0 R993 1-216-833-11 METAL CHIP 10K 5% 1/10W R994 1-216-833-11 METAL CHIP 10K 5% 1/10W

< TRANSFORMER >

T301 1-416-041-41 TRANSFORMER, BIAS OSCILLATION

< VIBRATOR >

X1 1-814-371-11 QUARTZ CRYSTAL UNITS (32.768kHz) X801 1-795-563-21 VIBRATOR, CERAMIC (16.9MHz) X802 1-814-254-21 VIBRATOR, CERAMIC (4.19MHz)*************************************************************

MOTOR BOARD *************

< SWITCH >

S701 1-572-085-21 SWITCH, LEAF (LIMIT)*************************************************************

A-1765-450-A POWER BOARD, COMPLETE (EXCEPT CND,E92,MX) A-1770-258-A POWER BOARD, COMPLETE (CND,E92,MX) ***********************

< CAPACITOR >


C906 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

< CONNECTOR >

CN903 1-822-674-11 HEADER ASSEMBLY FOR PRINTED WIRING BOARD

< DIODE >

D901 8-719-046-07 DIODE 2A02M D902 8-719-046-07 DIODE 2A02M D903 8-719-046-07 DIODE 2A02M D904 8-719-046-07 DIODE 2A02M

< FUSE HOLDER >

FH901 1-533-217-41 HOLDER, FUSE FH902 1-533-217-41 HOLDER, FUSE FH903 1-533-217-41 HOLDER, FUSE FH904 1-533-217-41 HOLDER, FUSE

< AC INLET >

0 J901 1-526-838-13 INLET, AC 2P (- AC IN) (EXCEPT CND,E92,MX)0 J901 1-540-009-13 INLET, AC (- AC IN) (CND,E92,MX)*************************************************************

RMC BOARD (supplied with MAIN BOARD, COMPLETE) **********

< CAPACITOR >

C963 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C964 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

< IC >

IC401 6-600-768-01 IC PNA4823M03S0 (IR)

< RESISTOR >

R426 1-216-821-11 METAL CHIP 1K 5% 1/10W*************************************************************

A-1765-456-A SWITCH BOARD, COMPLETE ***********************

< CONNECTOR >

CN318 1-815-446-11 PIN, CONNECTOR (PWB) 5P

< SWITCH >

S301 1-786-126-11 SWITCH, SLIDE (REC/PB)*************************************************************

MAIN MOTOR POWER RMC SWITCH

Ref. No. Part No. Description Remark

CFD-S07CP

4141

MISCELLANEOUS **************

52 1-831-985-32 CABLE, FLEXIBLE FLAT (5 CORE) 154 1-838-039-31 CABLE, FLEXIBLE FLAT (16 CORE) 156 1-831-758-32 CABLE, FLEXIBLE FLAT (6 CORE)0 158 A-1780-028-A OPTICAL PICK-UP (DA11MMVGP) 164 1-452-899-11 MAGNET

ANT1 1-754-711-11 ANTENNA, TELESCOPIC (FM)0 F901 1-533-468-12 FUSE, GLASS (DIA. 5) (T2AL/250V)0 F902 1-533-468-12 FUSE, GLASS (DIA. 5) (T2AL/250V) HE301 1-500-813-11 HEAD, ERASE (ERASE) HRP301 3-266-053-01 HEAD, RP (REC/PB)

S801 1-692-960-11 SWITCH, PUSH (1 KEY) (PUSH OPEN/CLOSE Z) SP101 1-826-280-61 SPEAKER (7.7cm) (L-CH) SP201 1-826-280-61 SPEAKER (7.7cm) (R-CH)0 T901 1-445-818-11 TRANSFORMER, POWER (CND,E92,MX,TW)0 T901 1-445-820-11 TRANSFORMER, POWER (E41,AUS,AR,CET,EA,IT,SP,TH)*************************************************************

ACCESSORIES ************

0 1-783-952-21 CORD, POWER (AR)0 1-829-433-13 CORD, POWER (TW)0 1-834-539-14 CORD, POWER (TH)0 1-835-070-12 CORD SET, POWER (EA)0 1-835-164-12 CORD SET, POWER (AUS)

0 1-836-379-12 CORD, POWER (E41,CET,EA,IT,SP)0 1-837-541-11 CORD, POWER (CND,E92,MX) 3-238-070-01 LID, BATTERY CASE (for RM-CE95A/CE95AD) 4-178-175-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (E92,MX) 4-178-175-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH) (CND)

4-178-175-31 MANUAL, INSTRUCTION (ENGLISH) (AUS,IT,TH) 4-178-175-41 MANUAL, INSTRUCTION (FRENCH,GERMAN)

(IT) 4-178-175-51 MANUAL, INSTRUCTION (SPANISH,ITALIAN) (IT) 4-178-175-61 MANUAL, INSTRUCTION

(DUTCH,PORTUGUESE) (IT) 4-178-175-71 MANUAL, INSTRUCTION (ENGLISH, SIMPLIFIED CHINESE) (SP)

4-178-175-91 MANUAL, INSTRUCTION (ENGLISH, TRADITIONAL CHINESE) (TW) 4-178-176-11 MANUAL, INSTRUCTION (FINNISH,SWEDISH) (CET) 4-178-176-21 MANUAL, INSTRUCTION (POLISH,HUNGARIAN) (CET) 4-178-176-31 MANUAL, INSTRUCTION (CZECH,SLOVAKIAN) (CET) 4-178-176-41 MANUAL, INSTRUCTION (RUSSIAN,UKRAINIAN) (CET)

4-178-176-51 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (E41,AR) 4-178-176-61 MANUAL, INSTRUCTION (ENGLISH,ARABIC) (EA) A-3172-070-A REMOTE COMMANDER (RMT-CE95AD) (CET,IT) A-3172-079-A REMOTE COMMANDER (RMT-CE95A) (EXCEPT CET,IT)

CFD-S07CP

REVISION HISTORY

Checking the version allows you to jump to the revised page.Also, clicking the version at the top of the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision1.0 2010.04 New

Documents

CFD-S07CP_988982301